Yamaha DVD-S2700 Manuel utilisateur

Marque: Yamaha

Modèle: DVD-S2700

Catégorie: Lecteurs DVD

Taper: Manuel utilisateur

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

DVD-S2700

DVD AUDIO/VIDEO SA-CD PLAYER

LECTEUR DE DVD AUDIO/VIDEO SA-CD

DVD-S2700

HDMI

POWER

AUDIO DIRECT

STANDBY

OFF

Printed in China CQX1A1139Z

00cv_DVD-S2700_G.fm Page 1 Thursday, August 24, 2006 4:06 PM

Important notes for users in the

U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp

plug. To change a fuse in this type of plug proceed

as follows:

1 Remove fuse cover and fuse.

2 Fix new fuse which should be a BS1362 5 Amp,

A.S.T.

3 Refit the fuse cover.

If the fitted plug is not suitable for your jack outlets,

it should be cut off and an appropriate plug fitted in

its place.

If the mains plug contains a fuse, this should have a

value of 5 Amp. If a plug without a fuse is used, the

fuse at the distribution board should not be greater

than 5 Amp.

Note: The severed plug must be disposed to avoid a

possible shock hazard should it be inserted into a 13

Amp jack elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the

following code:

blue = neutral (N), brown = live (L).

• As these colours may not correspond with the

colour markings identifying the terminals in your

plug, proceed as follows:

– Connect the blue wire to the terminal marked N

or coloured black

– Connect the brown wire to the terminal marked

L or coloured red.

– Do not connect either wire to the earth terminal

in the plug, marked E (or e) or coloured green (or

green and yellow).

Before replacing the plug cover, make certain that

the cord grip is clamped over the sheath of the lead -

not simply over the two wires.

Recording and playback of material may require

consent. See Copyright Act 1956 and The

Performer’s Protection Acts 1958 to 1972.

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai

asetusten muutto saattaa altistaa vaaralliselle säteilylle tai

muille vaarallisille toiminnoille.

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse

for stråling.

Bemærk: Netafbryderen STANDBY/ON er sekundært

indkoblet og ofbryder ikke strømmen fra nettet. Den

indbyggede netdel er derfor tilsluttet til lysnettet så længe

netstikket sidder i stikkontakten.

Observer: Nettbryteren STANDBY/ON er sekundert

innkoplet. Den innebygdenetdelen er derfor ikke frakoplet

nettet så lenge apparatet er tilsluttet nettkontakten.

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna

bruksanvisning specificerats, kan användaren utsättas för

osynlig laserstrålning, som överskrider gränsen för

laserklass 1.

Observera! Strömbrytaren STANDBY/ON är sekundärt

kopplad och inte bryter inte strömmen från nätet. Den

inbyggda nätdelen är därför ansluten till elnätet så länge

stickproppen sitter i vägguttaget.

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä

käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän

turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina

tippu-ja roiskevedelle.

Toiminnanvalitsin STANDBY/ON on kytketty

toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.

Sisäänrakennettu verkko-osa on kytkettynä

sähköverkkoon aina silloin, kun pistoke on pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou

de méthodes autres que ceux décrits ci-dessous,

peuvent entraîner une exposition à un rayonnement

dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die

Einstellung bzw. die Ausführung von anderen als in

dieser Anleitung beschriebenen Vorgängen kann zu

Gefährdung durch gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande

av åtgärder på annat sätt än så som beskrivs häri kan

resultera i farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure

non specificati in questo manuale possono risultare in

esposizione a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos

que no se especifican enste manual pueden causar una

exposición peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of

procedures anders dan beschreven in dit document kan

leiden tot blootstelling aan gevaarlijke stralen.

ПРЕДОСТЕРЕЖЕНИЕ

Использование органов управления или

произведение настроек или выполнение

процедур, не указанных в данной инструкции,

может отразиться на выделении опасной

радиации.

CAUTION

VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN. AVOID EXPOSURE TO BEAM.

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.

UNDGÅ UDSÆTTELSE FOR STRÅLING.

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL

ÅPNES. UNNGÅ EKSPONERING FOR STRÅLEN.

VARNING

SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR

DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VARO!

AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA

NÄKYMÄTTÖMÄLLE LASER SÄ TEILYLLE. ÄLÄ

KATSO SÄTEESEEN.

VORSICHT

SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL

AUSSETSEN.

DANGER

VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN. AVOID DIRECT EXPOSURE TO BEAM.

ATTE NTIO N

RAYONNEMENT LASER VISIBLE ET INVISIBLE EN

CAS D’OUVERTURE. EXPOSITION DANGEREUSE AU

FAISCEAU.

ПРЕДУПРЕЖДЕНИЕ

ПPИ OTKPЫTИИ УCTPOЙCTBA BЫ MOЖETE

ПОДBEPГHУTБСЯ ВОЗДЕЙСТВИЮ BИДИMOГO

И HEBИДИMOГO ЛAЗEPHOГO ИЗЛУЧEHИЯ.

ИЗБЕГAИTE BOЗДЕЙСТВИЯ ЛУЧA.

CAUTION-

VISIBLE AND INVISIBLE

LASER RADIATION WHEN OPEN. DO NOT

STARE INTO BEAM OR VIEW DIRECTLY

WITH OPTICAL INSTRUMENTS.

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

iii

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place

— away from direct sunlight, heat sources, vibration,

dust, moisture, or cold. In a cabinet, allow about 2.5 cm

(1 inch) of free space all around this unit for adequate

ventilation.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, nor locate this unit in an environment

with high humidity (i.e., a room with a humidifier) to

prevent condensation inside this unit, which may cause an

electrical shock, fire, damage to this unit, and/or personal

injury.

5 Avoid installing this unit in a location where foreign

objects may fall onto this unit or where this unit may be

exposed to liquid dripping or splashing. On the top of this

unit, do not place:

– Other components, as they may cause damage and/

or discoloration on the surface of this unit.

– Burning objects (i.e., candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall,

spilling the liquid and causing an electrical shock to

the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use excessive force on switches, knobs and/or

cords.

10 When disconnecting the power cord from the wall outlet,

grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Use only the voltage specified on this unit. Using this unit

with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than as

specified.

13 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any service

is needed. The cabinet should never be opened for any

reason.

14 When not planning to use this unit for long periods of

time (i.e., vacation), disconnect the AC power plug from

the wall outlet.

15 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

16 Before moving this unit, press STANDBY/ON to set the

unit in standby mode, then disconnect the AC power plug

from the wall outlet.

17 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

18 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt

to service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam.

When this unit is plugged into a wall outlet, do not place your

eyes close to the opening of the disc tray and other openings

or look inside.

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

The unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if you turn

off this unit by STANDBY/ON on the front panel or

STANDBY ( ) on the remote control. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

This symbol mark is according to the EU

directive 2002/96/EC.

This symbol mark means that electrical

and electronic equipment, at their end-of-

life, should be disposed of separately from

your household waste.

Please act according to your local rules

and do not dispose of your old products

with your normal household waste.

1 En

English

Playable disc formats.................................... 3

DVD region codes ............................................... 3

Patent information......................................... 4

Cleaning discs ............................................... 4

Supplied accessories.................................... 4

Front panel ..................................................... 5

Front panel display........................................ 6

Rear panel ...................................................... 7

Remote control .............................................. 8

General notes on connections ................... 10

Audio connections ...................................... 10

Connecting a stereo amplifier............................ 10

Connecting an AV receiver with 5.1ch/

digital input jacks .......................................... 10

Video connections....................................... 11

Connecting the power cable....................... 12

Step 1: Inserting batteries into the

remote control.......................................... 13

Using the remote control ................................... 13

Step 2: Turning on the power..................... 13

Step 3: Setting a TV type............................. 14

Step 4: Setting a language preference ...... 15

Setting the OSD (On-Screen Display)

language......................................................... 15

Setting the audio, subtitle and disc menu

languages ........................................................... 15

Basic operation............................................ 16

Pausing playback................................................ 16

Selecting a track/chapter .................................... 16

Searching backward/forward ............................. 17

Repeat playback........................................... 17

Repeating playback ............................................ 17

Repeating a section (except DVD-Audio/

MP3/WMA/JPEG) ......................................... 17

Random playback

(except DVD/DivX/SA-CD)........................ 17

Program playback (CD) ................................. 18

Disc menu operation (DVD/VCD/SVCD)..... 18

Using the DVD menu......................................... 18

Using the Video CD playback control (PBC)

menu (VCD/SVCD)....................................... 19

On-screen display (OSD) menu

(DVD/VCD/SVCD/SA-CD) ......................... 19

Using the OSD menu (DVD/VCD/SVCD/CD) .... 19

Displaying text information (SA-CD)................ 20

Zooming pictures (DVD-Video/VCD/

SVCD/DivX/JPEG)..................................... 20

Viewing angles (DVD-Video)....................... 21

Audio and Subtitle languages (DVD-Video)

... 21

Selecting an audio language............................... 21

Selecting a subtitle language.............................. 21

DivX external subtitle files .......................... 21

Changing pages (DVD-Audio)..................... 21

Group/File selection (DVD-Audio/DivX/

MP3/WMA/Kodak picture CD).................. 22

Selecting a group (DVD-Audio) ....................... 22

Selecting a file in a folder (DivX/MP3/WMA/

Kodak picture CD) ......................................... 22

Bonus group playback (DVD-Audio).......... 22

Changing the playback area and layer

(SA-CD)..................................................... 22

Multimedia file playback

(MP3/WMA/DivX/JPEG) ............................ 23

Displaying the thumbnail screen (JPEG) ........... 23

Rotating pictures (JPEG).................................... 23

CONTENTS

INTRODUCTION 3

FUNCTIONAL OVERVIEW 5

CONNECTIONS 10

GETTING STARTED 13

DISC OPERATION 16

2 En

Contents

Menu overview............................................. 24

Setup menu operation................................. 25

General setup menu .................................... 26

Selecting DVD-Audio mode.............................. 26

Selecting SA-CD mode...................................... 26

Setting the OSD language.................................. 26

Restricting playback with parental control ........ 26

Changing the parental password........................ 26

Setting the screen saver...................................... 27

Setting the auto power function ......................... 27

Setting the sleep timer........................................ 27

Resetting the system .......................................... 27

Displaying the DivX

VOD registration code ... 27

Audio setup menu ....................................... 28

Setting the analog output ................................... 28

Setting the digital output.................................... 28

Setting the LPCM output ................................... 28

Setting the night listening mode ........................ 28

Speaker setup menu.................................... 29

Setting speaker sizes .......................................... 29

Setting speaker distances ................................... 29

Setting speaker levels......................................... 30

Setting the SA-CD configuration....................... 30

Setting the cut-off frequency (SA-CD only)...... 30

Video setup menu........................................ 31

Setting the TV display ....................................... 31

Setting the TV type ............................................ 31

Selecting the black level

(U.S.A. and Canada models only) ................. 31

Selecting the closed caption

(U.S.A. and Canada models only) ................. 32

Setting the still mode ......................................... 32

Selecting the progressive scan function............. 32

Switching the SCART video out

(U.K. and Europe models only)..................... 33

Adjusting picture settings .................................. 33

HDMI setup menu ........................................ 33

Setting the HDMI video..................................... 33

Selecting the wide screen format ....................... 34

Selecting the DVI output range ......................... 34

Setting the HDMI audio..................................... 35

DISC setup menu......................................... 35

Selecting the default audio/subtitle/

DVD menu language ..................................... 35

Selecting an angle mark display ........................ 35

Selecting the PBC (playback control) function .... 35

Setting the duration for a slide show ..................35

SETUP MENU 24 LANGUAGE CODE LIST 36

TROUBLESHOOTING 37

GLOSSARY 39

SPECIFICATIONS 42

3 En

INTRODUCTION

English

Thank you for purchasing this unit. This Owner’s Manual

explains the basic operation of this unit.

• Illustrations in this manual are based on the U.K. and

Europe models unless otherwise specified.

• Notes contain important information about safety and

operating instructions.

• y indicates a tip for your operation.

• This manual is printed prior to production. Design and

specifications are subject to change in part as a result of

improvements, etc. In case of differences between the

manual and the product, the product has priority.

• This unit is designed for use with the following discs:

DVD-Video, DVD-Audio, DVD-R, DVD-RW,

DVD+R, DVD+RW, DVD+R DL, Video CD,

Super Video CD, Super Audio CD (SA-CD), Audio CD,

CD-R and CD-RW.

• This unit can play:

– MP3, WMA (except copyright-protected WMA) and

picture (Kodak, JPEG) files recorded on CD-R(W)/

DVD-R(W)/DVD+R(W)

– JPEG/ISO 9660 format

– Maximum 14 character display

–DivX

disc on CD-R(W)/DVD-R(W)/DVD+R(W)

– Official DivX

Certified product

– Plays all versions of DivX

video (including

DivX

6) with standard playback of DivX

media

files

• CD-R(W), DVD-R(W) and DVD+R(W) cannot be played

unless finalized.

• Copyright-protected WMA files cannot be played with this

unit.

• Some discs cannot be played depending on the recording

conditions, such as the PC environment and application

software. The characteristics and condition of some discs;

materials, scratches, curvature, etc., may result in playback

failure.

• Be sure to use only CD-R(W), DVD-R(W) and DVD+R(W)

discs made by reliable manufacturers.

• Do not use any non-standard shaped discs (heart-shaped, etc.).

• Do not use discs with tape, seals, or paste on their surface.

Doing so may damage this unit.

• Do not use discs affixed with labels printed by a commercially

available label printer.

DVD region codes

This unit is designed to support the region management

system. Check the regional code number on the DVD disc

package. If the number does not match the region code of

this unit (see the table below or the back of this unit), this

unit may be unable to play the disc.

INTRODUCTION

Playable disc formats

Notes

Destination

Region code

of this unit

Playable discs

U.S.A.

Canada

U.K.

Europe

Australia

China

ALL

4 En

INTRODUCTION

–

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

“DTS” and “DTS Digital Surround” are registered

trademarks of Digital Theater Systems, Inc.

DivX, DivX Certified, and associated logos are

trademarks of DivX, Inc. and are used under license.

“DCDi” is a trademark of Faroudja, a division of Genesis

Microchip, Inc.

“HDMI”, the “HDMI” logo and “High Definition

Multimedia Interface” are trademarks or registered

trademark of HDMI Licensing LLC.

• When a disc becomes dirty, clean it with a cleaning

cloth. Wipe the disc from the center out. Do not wipe in

a circular motion.

• Do not use solvents such as benzine, thinner,

commercially available cleaners, or antistatic spray

intended for analog records.

Check your package to make sure it contains the following

items:

Patent information

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home and other limited

viewing uses only unless otherwise authorized by

Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

Cleaning discs

Supplied accessories

HDMI

POWER

LIGHT

DIMMER

MULTI 2CH

RANDOM

AUDIO DIRECT STANDBY

GROUP PAGE

PROG

REPEAT

SUBTITLE

SETUP

AUDIO ZO OM

ANGLE

PAUSE

STOP

SKIP

PLAY

A B

SLOW SEARCH

ENTERCLEAR

ON SCREENTOP MENU

MENU RETURN

ENTER

Audio pin cable

Batteries (x2)

(AAA, R03, UM-4)

Remote

control

Power cable

Video pin cable

5 En

FUNCTIONAL OVERVIEW

English

1 Disc tray

Load a disc in the disc tray.

2 AUDIO DIRECT indicator

Lights up when you select the AUDIO DIRECT mode

by pressing AUDIO DIRECT on the remote control.

3 STANDBY/ON

Turns on this unit or sets it to the standby mode.

• This switch is operational only when POWER switch (5) is

pressed inward to the ON position.

• In the standby mode, this unit consumes a small amount of

power to receive infrared signals from the remote control.

4 POWER indicator

Lights up when this unit is on.

5 POWER switch

Press inward to the ON position to turn on the power of

this unit. Press again to release it outward to the OFF

position to turn off this unit.

6 HDMI indicator

Lights up green when an HDMI component is

recognized by this unit and the HDMI mode is set to

on.

Lights up orange when no HDMI component is

recognized by this unit while the HDMI mode is set to

on.

7 Front panel display

Displays playback information or settings.

Opens or closes the disc tray.

9 b/w

Searches backward.*

Moves to the previous chapter or track.

0 f/a

Searches forward.*

Moves to the next chapter or track.

q p

Starts playback.

w e

Pauses playback.

e s

Stops playback.

* Press and hold the button for about three seconds.

FUNCTIONAL OVERVIEW

Front panel

HDMI

POWER

AUDIO DIRECT

STANDBY

OFF

8 9 0 w e

3 64 7

1 2

Notes

6 En

FUNCTIONAL OVERVIEW

1 P.SCAN indicator

Lights up when the progressive scan function is

activated.

2 Playback mode indicators

Display the icon for the selected playback mode.

3 Decoder indicators

Display the icon for the selected internal decoder.

4 MULTI indicator

Lights up when playing the multi-channel audio

source.

5 D.MIX indicator (DVD-Audio only)

Lights up when playing the disc that allows down

mixing of the multi-channel audio source.

6 Disc indicators

Display the icon for the disc type.

7 Information display

Displays various information such as a title/chapter/

track number or elapsed playing time.

You can adjust the brightness of the front panel display using

DIMMER on the remote control.

Front panel display

MP3 JPEG

SVCD WMA

DVD AUDIO

SA-CD

DivX

P.SCAN TITLE GROUP CHP/ TRK MULTI D.MIX PROG. RANDOM ALL AD

252134

7 En

FUNCTIONAL OVERVIEW

English

1 AUDIO OUT (6ch discrete) jacks

Connect to the 6ch input jacks of your AV receiver.

2 AUDIO OUT (MIXED 2CH) jacks

Connect to the audio input jacks of your AV receiver or

stereo system.

3 DIGITAL (COAXIAL) jack

Connect to the coaxial input jack of your AV receiver.

4 VIDEO OUT (VIDEO) jack

Connect to the composite video input jack of your AV

receiver.

5 REMOTE CONTROL (IN/OUT) connectors

Use in custom installations to transmit remote control

signals via cable connections.

6 REMOTE CONTROL (RS-232C) terminal

(U.S.A., Canada, Australia, U.K. and Europe

models only)

Use as an expansion terminal for commercial use.

Consult your dealer for details.

7 MAINS

Connect the supplied power cable.

8 HDMI jack

Connect to the HDMI input jack of your HDMI

component.

9 DIGITAL (OPTICAL) jack

Connect to the optical input jack of your AV receiver.

0 AV terminal

(U.K. and Europe models only)

Connect to SCART input terminal of your TV.

q VIDEO OUT (S VIDEO) jack

Connect to the S-video input jack of your AV receiver.

w VIDEO OUT (COMPONENT) jacks

Connect to the component input jacks of your AV

receiver.

■ Remote control connectors and RS-232C terminal

The REMOTE CONTROL (IN/OUT) connectors and the REMOTE CONTROL (RS-232C) terminal are used in

custom installation. Do not connect any cables to these connectors during normal use.

(For U.S.A., Canada, Australia, U.K. and Europe models, keep the RS-232C switch set to OFF.)

Caution: Do not touch the inner pins of the jacks on the rear panel of this unit. Electrostatic discharge

may cause permanent damage to this unit.

Rear panel

MIXED 2CH

AUDIO OUT DIGITAL

REMOTE CONTROL

VIDEO OUT

FRONT

COAXIAL

OPTICAL

RS-232C

HDMI

S VIDEO

R / CR PB / CB Y

VIDEO

MAINS

OUT

SUBWOOFER

CENTER

SURROUND

COMPONENT

ON OFF

263

145

98 0 w

(U.K. and Europe models)

8 En

FUNCTIONAL OVERVIEW

1 LIGHT

Lights up the remote control buttons.

2 DIMMER

Selects from three different levels of brightness for the

front panel display: medium, low and auto.

For auto setting, brightness is automatically set to low

only during playback.

3 HDMI

Switches the HDMI mode on or off.

4 GROUP

Selects the DVD-Audio group.

5 PAGE (+/–)

Selects the DVD-Audio still picture.

6 Numeric buttons (0-9)

Select numbered items in the currently displayed

menu.

7 CLEAR

Clear the mode or setting.

8 SETUP

Accesses or exits from the setup menu of this unit.

9 STOP (

)

Stops playback.

0 PAUSE (

)

Pauses playback temporarily.

Frame-by-frame playback.

q SKIP (

l22 / 33l)

Moves to the previous/next chapter or track.

w TOP MENU

Displays the top-level disc menu.

Remote control

HDMI

POWER

LIGHT

DIMMER

MULTI 2CH

RANDOM

AUDIO DIRECT STANDBY

GROUP PAGE

PROG

REPEAT

SUBTITLE

SETUP

AUDIO ZOOM

ANGLE

PAUSE

STOP

SKIP

PLAY

A B

SLOW SEARCH

ENTERCLEAR

ON SCREENTOP MENU

MENU RETURN

ENTER

;

9 En

FUNCTIONAL OVERVIEW

English

e Cursors ( / / / )

Selects an item in the currently displayed menu.

ENTER

Confirms the menu selection.

r MENU

Accesses the menu of a disc.

t SUBTITLE

Selects the subtitle language.

y AUDIO

Selects the audio language or format.

u POWER (

)

Turns on this unit.

i STANDBY ( )

Sets this unit to the standby mode.

o AUDIO DIRECT

Switches the video output on or off during playback.

This function is not available for HDMI output.

During the playback in the AUDIO DIRECT mode, the

front panel display goes out.

p MULTI

/ 2CH

Selects a sound mode: Stereo or Multi-channel.

Changes the SA-CD playback area.

a PROG

Accesses the program setup menu to program disc

tracks or exit from its menu.

s RANDOM

Plays tracks in random order.

d REPEAT

Repeats the chapter, track, title, group or disc.

f A-B

Repeats a specific segment.

g ENTER

Confirms the menu selection.

h SLOW / SEARCH (22 / 33)

Searches backward or forward.

j PLAY (

)

Starts playback.

k ON SCREEN

Accesses or exit from the on-screen display (OSD)

menu of this unit.

l RETURN

Returns to the previous setup menu.

; ZOOM

Enlarges the video image.

z ANGLE

Selects the DVD camera angle.

Two ENTER buttons (e and g) act in the same way.

CONNECTIONS

10 En

Be sure to turn off this unit and unplug the power supply

cable, before you make or change connections.

• Depending on the component you want to connect, there

are various ways to make connections. Possible

connections are described below.

• Refer to the manuals supplied with your other

components as necessary to make the best connections.

• Do not connect this unit via your VCR. The video

quality could be distorted by the copy protection system.

• Do not connect the audio out jack of this unit to the

phono in jack of your audio system.

This unit has digital coaxial, digital optical, analog 6ch

discrete, analog mixed 2ch and HDMI output jacks.

Connection depends on the availability of audio jacks on

your component.

Connecting a stereo amplifier

Connect AUDIO OUT (MIXED 2CH) jacks of this unit to

the corresponding input jacks of your audio component

(such as a stereo amplifier) using the supplied audio pin

cable. You can connect a subwoofer to the

SUBWOOFER jack.

Connecting an AV receiver with 5.1ch/

digital input jacks

■ Analog connections

If you want to reproduce multi-channel Super Audio CD

(SA-CD) and DVD-Audio, connect AUDIO OUT (6ch

discrete) jacks of this unit to the corresponding input

jacks of your AV receiver using commercially available

audio pin cables.

CONNECTIONS

General notes on connections

Audio connections

MIXED 2CH

AUDIO OUT DIGITAL

REMOTE

VIDEO OUT

FRONT

COAXIAL

OPTICAL

S VIDEO

R / CR PB / CB Y

VIDEO

OUT

SUBWOOFER

CENTER

SURROUND

COMPONENT

ON OFF

CD / DVD

HDMI

This unit (U.K. and Europe models)

Stereo

amplifier

Left

speaker

Right

speaker

Subwoofer

Audio pin cable

(supplied)

MIXED 2CH

AUDIO OUT DIGITAL

REMOTE

VIDEO OUT

FRONT

COAXIAL

OPTICAL

HDMI

S VIDEO

R / CR PB / CB Y

VIDEO

OUT

SUBWOOFER

CENTER

SURROUND

COMPONENT

ON OFF

FRONT

SURROUND

CENTER

SUBWOOFER

This unit (U.K. and Europe models)

AV receiver

Speakers

11 En

CONNECTIONS

English

■ Digital connections

If you want to use the Dolby Digital, DTS or MPEG

function on your AV receiver, connect HDMI <A> or

DIGITAL (COAXIAL) or DIGITAL (OPTICAL)

<C> jack of this unit to the corresponding input jacks of

your AV receiver using a commercially available HDMI,

digital coaxial or digital optical cable.

See “HDMI jack <A>” on page 12 about HDMI

connection.

• If you make a connection with DIGITAL (COAXIAL) or

DIGITAL (OPTICAL) <C>, set [Digital Out] to [All] (see

“Setting the digital output” on page 28).

• If the audio format of the digital output does not match the

capabilities of your receiver, the receiver produces a distorted

sound or no sound at all. Make sure to select the appropriate

audio format from the menu screen on the disc.

Pressing AUDIO on the remote control once or more may

change not only the audio languages but also the audio format.

• SA-CD audio signals are not output from DIGITAL

(COAXIAL/OPTICAL) jacks.

• If you want to enjoy Dolby Digital, DTS, and MPEG formats,

you must connect this unit to an AV receiver that supports

these formats.

This unit has HDMI, composite video, S-video,

component video and SCART output jacks. If your AV

receiver has video output jacks, connect your receiver and

then your TV so that you can use one TV for several

different video sources (LD, VCR etc.) by simply

switching the input source selector on your receiver.

Use the one that corresponds to the input jacks on the

component to be connected.

Notes

MIXED 2CH

AUDIO OUT DIGITAL

REMOT

VIDEO OUT

FRONT

COAXIAL

OPTICAL

HDMI

S VIDEO

R / CR PB / CB Y

VIDEO

OUT

SUBWOOFER

CENTER

SURROUND

COMPONENT

ON OFF

COAXIAL

OPTICAL

HDMI

<C><A>

This unit (U.K. and Europe models)

AV receiver

Speakers

Video connections

MIXED 2CH

AUDIO OUT DIGITAL

REMOTE CONTROL

VIDEO OUT

FRONT

COAXIAL

OPTICAL

RS-232C

S VIDEO

R / CR PB / CB Y

VIDEO

OUT

SUBWOOFER

CENTER

COMPONENT

ON OFF

S-VIDEO

VIDEO

HDMI

VIDEO

OUT

VIDEO

HDMI

OUT

HDMI

S VIDEO

OUT

COMPONENT

VIDEO OUT

COMPONENT

VIDEO IN

S VIDEO

PR/CR YPB/CB

COMPONENT VIDEO IN

HDMI

This unit (U.K. and Europe models)

Video

pin cable

(supplied)

receiver

12 En

CONNECTIONS

■ HDMI jack <A>

HDMI (High-Definition Multimedia Interface) provides

high quality digital audio and video on a single

connection. Connect HDMI jack of this unit to the HDMI

input jack of your AV receiver, and then to that of your TV

using a commercially available HDMI cable.

If your receiver does not have HDMI output jack, you can

achieve a better video image by connecting HDMI jack of

this unit directly to the HDMI input jack of your TV.

• To output HDMI signals, set the HDMI mode to “on” by

pressing HDMI button on the remote control.

• You can use an HDMI-DVI converter cable in order to connect

this unit to HDCP-compatible DVI-D components. In this case,

you need to use another audio connection in addition to this

connection because no audio signals are output.

■ Composite video jack

Connect VIDEO OUT (VIDEO) jack of this unit to the

video input jack of your AV receiver, and then to that of

your TV using the supplied video pin cable.

■ S-video jack <C>

S-video connections achieve a clearer picture than

composite video connections by transmitting video signals

on separate wires for luminance (Y) and chrominance (C).

Connect VIDEO OUT (S VIDEO) jack of this unit to

S-video input jack of your AV receiver, and then to that of

your TV using a commercially available S-video cable.

■ Component video jacks <D>

Component video connections achieve higher fidelity

color reproduction than S-video connections by

transmitting video signals on separate wires for luminance

(Y: green) and chrominance (P

B: blue, PR: red). Connect

VIDEO OUT (COMPONENT) jacks of this unit to the

component input jacks of your AV receiver, and then to

those of your TV using a commercially available

component cable. Observe the color of each jack when

you make connections.

If your receiver does not have component output jacks,

you can achieve a better video image by connecting the

component output jacks of this unit directly to the

component input jacks of your TV.

■ SCART terminal <E>

(U.K. and Europe models only)

If your TV has only a terminal for video input, you can

connect the TV directly to this unit.

Connect AV terminal of this unit to SCART input terminal

of your TV using a commercially available SCART cable.

• Ensure that the “TV” indication on SCART cable is connected

to the TV set and “DVD” indication on SCART cable is

connected to this unit.

After all other connections are complete, plug the supplied

power cable into MAINS of this unit and then plug the

power cable to an AC outlet.

Notes

Note

Connecting the power cable

MAINS

To an AC

outlet

13 En

GETTING STARTED

English

1 Press the part and slide the battery

compartment cover off.

2 Insert the two supplied batteries (AAA, R03,

UM-4), following the indications (+/–) on the

inside of the compartment.

3 Slide the cover back until it snaps into place.

• Insert batteries correctly according to the polarity markings

(+/–). The batteries inserted in the opposite direction may leak.

• Replace the exhausted batteries immediately with new ones to

prevent a leakage.

• Remove the batteries from the compartment if the remote

control is not used for more than a month.

• If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as these

different types of batteries may have the same shape and color.

• Dispose of the batteries correctly in accordance with your local

regulations.

Using the remote control

Use the remote control within 6 m (20 ft approx.) of this

unit and point it toward the remote control sensor.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– places of high humidity, such as near a bath

– places of high temperature, such as near a heater or stove

– places of extremely low temperature

– dusty places

1 Make sure that the power cable is connected to

an AC outlet.

2 Turn on your TV and AV receiver.

3 Select the appropriate input source of the AV

receiver connected to this unit. Refer to the

manual supplied with your AV receiver for

details.

4 Press POWER switch on the front panel.

➜ The POWER indicator lights up orange.

5 Press STANDBY/ON on the front panel or

POWER (

) on the remote control to turn on

this unit.

➜ The POWER indicator lights up green and the

front panel display lights up.

6 Set the TV to the correct Video IN channel (e.g.,

EXT1/2, AV1/2, AUDIO/VIDEO, etc. Refer to

the manual supplied with your TV for details).

➜ The default screen appears on the TV.

GETTING STARTED

Step 1: Inserting batteries into

the remote control

Notes

HDMI

within 6m

(20 ft approx.)

Notes

Step 2: Turning on the power

14 En

GETTING STARTED

This unit is compatible with both NTSC and PAL video

formats. Select the color system that matches your TV.

• Before changing the current TV Standard setting, ensure that

your TV supports the selected TV type system.

• If you play an NTSC-formatted disc with the [PAL] setting or a

PAL-formatted disc with the [NTSC] setting, the video quality

may deteriorate.

1 Press SETUP.

➜ The setup menu appears.

2 Press / repeatedly to select [VIDEO],

and then press ENTER.

➜ [VIDEO] menu appears.

3 Press / repeatedly to highlight [TV

Type].

4 Press / to select one of the options below.

PAL

Select this if the connected TV is a PAL system TV. It will

change video signals of NTSC discs and output them in

PAL format.

NTSC

Select this if the connected TV is an NTSC system TV. It

will change video signals of PAL discs and output them in

NTSC format.

Step 3: Setting a TV type

Notes

1/2

SETUP

GENERAL

AUDIO

SPEAKER

VIDEO

HDMI

DISC

DVD-Audio mode

SA-CD mode

OSD Language

Parental Rating

Parental Password

Screen Saver

Auto Power Off

Sleep Timer

Select : Enter

Move :

Return

1/1

VIDEO

TV Display

TV Type

Black Level*1

Closed Caption*1

Still Mode

Progressive Scan

Scart Video Out*2

Picture Setting

Select : Enter

Move :

16:9

PAL

Off

Field

Off

RGB

Return

*1: [Black Level] and [Closed Caption] are only for U.S.A. and

Canada models.

*2: [Scart Video Out] is only for U.K. and Europe models.

1/1

VIDEO

TV Display

TV Type

Black Level*1

Closed Caption*1

Still Mode

Progressive Scan

Scart Video Out*2

Picture Setting

Select : Enter

Move :

Return

16:9

PAL

Off

Field

Off

RGB

15 En

GETTING STARTED

English

You can select your own preferred language settings. This

unit will automatically switch to your preferred language

for you whenever you load a disc. If the language selected

is not available on the disc, the default language of the disc

will be used instead. The OSD (On-Screen Display)

language in the system menu will remain once selected.

Setting the OSD (On-Screen Display)

language

1 Press SETUP.

➜ The setup menu appears.

2 Press / repeatedly to highlight

[GENERAL], and then press ENTER.

➜ [GENERAL] menu appears.

3 Press / repeatedly to highlight [OSD

Language].

4 Press / to select a language.

Setting the audio, subtitle and disc

menu languages

1 Press SETUP.

➜ The setup menu appears.

2 Press / repeatedly to highlight [DISC],

and then press ENTER.

➜ [DISC] menu appears.

3 Press / repeatedly to highlight [AUDIO

Language] or [Subtitle Language] or [DVD

Menu Language].

4 Press / to select a language.

■ To select the language not in the list:

1 Select [Others] under [AUDIO Language] or

[Subtitle Language] or [DVD Menu Language].

2 Press ENTER.

3 Use the numeric buttons (0-9) to enter the

4-digit language code (see “LANGUAGE CODE

LIST” on page 36).

4 Press ENTER.

Step 4: Setting a language

preference

1/2

GENERAL

DVD-Audio mode

SA-CD mode

OSD Language

Parental Rating

Parental Password

Screen Saver

Auto Power Off

Sleep Timer

Select : Enter

Move :

DVD-Audio

SA-CD

English

Level 8

Mode 1

Off

Return

1/1

DISC

AUDIO Language

Subtitle Language

DVD Menu Language

Angle Mark

PBC

Time Interval

Select : Enter

Move :

Return

English

Off

English

Off

3 sec

DISC OPERATION

16 En

• Unless otherwise specified, all operations described here are

carried out using the supplied remote control.

• If the inhibition icon ( or “Prohibit”) appears on the TV

screen when you press a button, the function for that button is

not available on the current disc or at the current time.

• Depending on the DVD or Video CD disc, some operations

may operate differently or be restricted.

• Do not push on the disc tray or put any objects other than discs

on the disc tray. Doing so may cause the disc unit to

malfunction.

1 Press on the front panel to open the disc tray.

2 Place a disc in the disc tray with the printed side

up.

3 Press again to close the disc tray.

➜ After recognizing the disc, this unit starts to play

back automatically.

• If you press PLAY (

) when the disc tray is

opened, the disc tray closes and playback starts

automatically.

• Depending on the disc, the disc reading time may

exceed 30 seconds due to the complexity of the

directory/file configuration.

4 To stop playback, press STOP (

➜ “RESUME” appears in the front panel display.

5 To resume playback, press PLAY (

➜ The disc is played back from the last stopping

point.

As long as you do not eject a disc, you can resume playback even

if you turn off this unit.

6 To cancel resume mode, press STOP (

)

twice.

• It may not be possible to play certain MP3/JPEG/DivX discs

due to the configuration and characteristics of the disc or the

recording conditions.

• When you play a down mix prohibited disc, “NO DOWN

MIX” lights in the front panel display.

Pausing playback

1 During playback, press PAUSE (

➜ Playback is paused and the sound is muted.

2 Press PAUSE (

) again to select the next

picture frame.

3 To resume normal playback, press PLAY (

Selecting a track/chapter

Press SKIP (l22 / 33l) or use the numeric

buttons (0-9) to select a track/chapter number.

• You can move to the top of the currently playing

track/chapter by pressing SKIP (

l22 ) once, and

move to the previous track/chapter by pressing

SKIP (l22 ) twice.

• During repeat playback of a track/chapter, press

SKIP (l22 / 33l) to replay the same track/

chapter.

DISC OPERATION

Notes

Basic operation

MULTI 2CH

RANDOM

GROUP PAGE

PROG

REPEAT

SETUP

PAUSE

STOP

SKIP

PLAY

A B

SLOW SEARCH

ENTERCLEAR

ON SCREENTOP MENU

STOP ( )

PAUSE ( )

SKIP ( / )

SLOW/SEARCH

( / )

PLAY ( )

Numeric

buttons (0-9)

Notes

La page charge ...

Yamaha DVD-S2700 Manuel utilisateur

Marque: Yamaha

Modèle: DVD-S2700

Catégorie: Lecteurs DVD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha DVD-S2700 Manuale utente
English: Yamaha DVD-S2700 User manual
Deutsch: Yamaha DVD-S2700 Benutzerhandbuch
Nederlands: Yamaha DVD-S2700 Handleiding
dansk: Yamaha DVD-S2700 Brugermanual
svenska: Yamaha DVD-S2700 Användarmanual
Türkçe: Yamaha DVD-S2700 Kullanım kılavuzu
română: Yamaha DVD-S2700 Manual de utilizare

Yamaha DVD-S2700 Manuel utilisateur

Yamaha DVD-S2700 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents