Hatco TQ Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
TQ Series
Catégorie
Grille-pain
Taper
Le manuel du propriétaire
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 19)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 19
AVERTISSEMENT
Toast-Qwik
®
Conveyor Toasters
Grille-pain à convoyeur
TQ-10, TQ-400, TQ-800,
TQ-1200, and TQ-1800 Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
P/N 07.04.354.00 © 2019 Hatco Corporation
2
Form No. TQ2M-1219
English
INTRODUCTION
Hatco Toast-Qwik
®
Conveyor Toasters are specially designed
to accelerate the toasting operation. Products for toasting pass
through a heating chamber for rapid and thorough toasting.
Moisture, sugar content, and thickness of bread product effect
the ability to achieve the perfect toasted product. Conveyor
speed and temperature determine the toasting color.
Hatco toasters are built with quality to meet the demands
of foodservice operations and provide years of trouble-free
performance. The metal-sheathed tubular heating elements
are guaranteed against breakage and burnout for two years.
Hatco Toast-Qwik Conveyor Toasters are products of extensive
research and field testing. The materials used were selected
for maximum durability, attractive appearance and optimum
performance. Every unit is thoroughly inspected and tested
prior to shipment.
This manual provides the installation, safety, and operating
instructions for Toast-Qwik Conveyor Toasters. Hatco
recommends all installation, operating, and safety instructions
appearing in this manual be read prior to installation or
operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Descriptions ..............................................................4
Model Designation ...............................................................5
Specifications .......................................................................6
Plug Configurations .............................................................6
Electrical Rating Charts ....................................................... 6
Dimensions .......................................................................... 8
Installation ...........................................................................10
General .............................................................................. 10
Front or Rear Discharge Installation ................................. 11
Operation .............................................................................12
General .............................................................................. 12
Operating Model TQ-10 .....................................................12
Operating TQ-400, -800, -1200, and -1800 Series ...........13
Power Save Mode with Indicator Light ..............................14
Adjusting the Toast Feed Ramp ........................................14
Maintenance ........................................................................15
General .............................................................................. 15
Daily Cleaning ...................................................................15
Cleaning the Toast Feed Ramp .........................................15
Cleaning the Bottom Element Reflector ............................15
Troubleshooting Guide ......................................................16
Options and Accessories ..................................................17
Limited Warranty ................................................................18
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and
purchase date of the unit in the spaces below (specification
label located on the lower left hand side of the unit). Please
have this information available when calling Hatco for service
assistance.
Model No. ________________________________________
Serial No. _________________________________________
Voltage ___________________________________________
Date of Purchase ___________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00  to 5:00  Monday–Friday,
Central Time (CT)
(Summer Hours — June to September:
7:00  to 5:00  Monday–Thursday
7:00  to 4:00  Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
CONTENTS
Form No. TQ2M-1219
3
English
IMPORTANT SAFETY INFORMATION
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing maintenance, cleaning,
setup, or attempting to clear a jam.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C)
and a maximum of 85°F (29°C).
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• NEVER insert a knife, fork, or similar object into
toasting chamber.
• Do not pick up the toaster by inserting fingers into the
toaster feed opening.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
If toaster overheats or cooling fan inside unit stops
working, the safety high-limit switch will shut off toaster.
Contact Authorized Service Agent or Hatco for assistance.
WARNING
FIRE HAZARD:
• For front discharge operation: Allow a minimum
clearance of 1″ (25 mm) along the sides and rear of
unit. Allow a minimum clearance of 12″ (305 mm) in the
front. If safe distances are not maintained, discoloration
or combustion could occur.
• For rear discharge operation: Allow a minimum
clearance of 1″ (25 mm) along the sides of unit. Allow
a minimum clearance of 12″ (305 mm) in the front and
rear. If safe distances are not maintained, discoloration
or combustion could occur.
• Do not locate toaster under shelving or closer than 12″
(305 mm) from the ceiling.
• Do not place anything on top of toaster. Do not
place toaster near or underneath curtains or other
combustible materials. Items near or on top of toaster
could catch fire causing injury and/or damage to the
toaster.
• In case of fire, disconnect toaster from power source
immediately. This allows unit to cool, making it easier
and safer to put out fire.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Do not remove crumb tray for cleaning until toaster is
cool.
Locate unit at the proper counter height in an area that is
convenient for use. Location should be level and strong
enough to support weight of unit and contents.
Always operate toaster with crumb tray installed.
If Warning light comes on, unit is malfunctioning. Turn
off or disconnect unit from power supply and have unit
serviced by a qualified technician.
Toasting of coated or buttered products such as garlic
bread, cheese sandwiches, and sweet rolls is NOT
recommended. Residue will reduce toaster performance
and could ignite inside toaster. Using toaster with food
products listed above will void unit warranty.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
4
Form No. TQ2M-1219
English
IMPORTANT SAFETY INFORMATION
MODEL DESCRIPTIONS
All Models
All Toast-Qwik
®
Conveyor Toasters are fast, reliable, and
versatile, toasting 300 to 1800 slices of bread product per hour
depending on the specific model. The front or rear discharge
lets the operator place a Toast-Qwik toaster where it is most
convenient. Every Toast-Qwik toaster includes a toast collector
pan, toast feed ramp, removable crumb tray, and a factory
attached 6’ (1829 mm) cord and plug.
Power Save Mode with Indicator Light
All TQ-400, TQ-800, TQ-1200, and TQ-1800 series toasters
have a Power Save mode. During the Power Save mode the
indicator light on the POWER SAVE button will flash. While
the light is flashing the toaster is operating at 50% power. Full
power can be restored within 10 minutes by pushing any button
or adjusting any control knob.
ColorGuard System
All TQ-400, TQ-800, TQ-1200, and TQ-1800 series toasters
use a patented ColorGuard Sensing System that monitors
and automatically adjusts conveyor speed during high usage
periods to assure toast color uniformity.
TQ-10 Model
The TQ-10 model allows for toasting of bread products up to


TQ-10 Model
TQ-400 Model
The TQ-400 model allows for toasting of bread products up to

TQ-405 Model
The TQ-405 model allows for toasting of moist or dense bread

TQ-400H Model



TQ-400BA Model
The TQ-400BA model allows for quick single-sided toasting of


as 45 seconds. Toasts cut side facing up.
TQ-400 Series (TQ-400 shown)
WARNING
Do not locate unit in an area subject to temperatures above
85°F (29°C) or grease from grills, fryers, etc. Excessive
temperatures and grease could cause damage to unit.
Do not locate toaster in an area that restricts air flow
around front or rear of unit. Do not locate toaster in direct
discharge path of air conditioning vent or makeup air vent.
Damage to any countertop material caused by heat
generated from Hatco equipment is not covered under
the Hatco warranty. Contact manufacturer of countertop
material for application information.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
This unit is intended for commercial use only — NOT for
household use.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Form No. TQ2M-1219
5
English
MODEL DESCRIPTIONS
TQ-800 Model
The TQ-800 model allows for toasting of bread products up to

TQ-805 Model
The TQ-805 model allows for toasting of moist or dense bread

TQ-800H Model



TQ-800BA Model
The TQ-800BA model allows for quick single-sided toasting of


as 30 seconds. Toasts cut side facing up.
TQ-800HBA Model
The TQ-800HBA model is designed to provide the flexibility and
performance to toast one side of sliced bagels or bun products
in as little as 30 seconds. Toasts cut side facing up. Maximum
         
(244 mm) wide.
TQ-800 Series (TQ-800H shown)
TQ-1200 Model
The TQ-1200 is a high speed toaster which has an accelerated
conveyor system allowing faster toasting during periods of high
demand. Two slices of bread products can be toasted in as
little as 15 seconds. This model is capable of toasting bread

TQ-1800 Model
The TQ-1800 model allows for toasting of bread products up to

TQ-1800H Model



TQT-1800BA Model
The TQ-1800BA model allows for quick single-sided toasting


as 15 seconds. Toasts cut side facing up.
TQ-1800HBA Model
The TQ-1800HBA model is designed to provide the flexibility
and performance to toast one side of sliced bagels or bun
products in as little as 15 seconds. Toasts cut side facing up.
   

TQ-1800 Series (TQ-1800 shown)
T Q - x x x x H B A
Toast Qwik
Model Number
H = Opening height is 3″ (76 mm)
No Character = Opening height is 2″ (51 mm)
BA = Toasts one side only
(Buns/Bagels)
No Character = Toasts Both Sides
MODEL DESIGNATION
6
Form No. TQ2M-1219
English
Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight
TQ-400 120
60
1790
14.9
NEMA 5-15P*
46 lbs. (21 kg)
208
2230
10.7
NEMA 6-15P
240 9.3
TQ-400H 208
60 2230
10.7
NEMA 6-15P 46 lbs. (21 kg)
240 9.3
TQ-400BA 120
60
1780
14.8
NEMA 5-15P*
46 lbs. (21 kg)
208
1880
9.0
NEMA 6-15P
240 7.8
Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight
TQ-10 120
60 1800
15.0 NEMA 5-15P*
42 lbs. (19 kg)
208 8.8
NEMA 6-15P
240 7.6
SPECIFICATIONS
Electrical Rating Chart — Model TQ-10
Electrical Rating Chart — TQ-400 Series
* NEMA 5-20P for Canada.
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug. Plugs are supplied according to the application.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install proper voltage and size electrical receptacle.
NOTE: Receptacles are not supplied by Hatco, but are
available as accessories.
NOTE: Specification label located on the side of the unit. See
label for serial number and verification of unit electrical
information.
NEMA 5-15P
NEMA 6-20P
NEMA 6-15P
NEMA 6-30P
NEMA 5-20P
Plug Configurations
Form No. TQ2M-1219
7
English
Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight
TQ-800 208
60 3330
16.0 NEMA 6-20P†
62 lbs. (28 kg)
240 13.9 NEMA 6-15P‡
TQ-800H 208
60 3330
16.0 NEMA 6-20P†
62 lbs. (28 kg)
240 13.9 NEMA 6-15P‡
TQ-800BA 208
60 3280
15.8 NEMA 6-20P†
62 lbs. (28 kg)
240 13.7 NEMA 6-15P‡
TQ-800HBA 208
60 3280
15.8 NEMA 6-20P†
62 lbs. (28 kg)
240 13.7 NEMA 6-15P‡
SPECIFICATIONS
Electrical Rating Chart — TQ-800 Series
* NEMA 5-20P for Canada
† Available with optional 6-30P cord
‡ NEMA 6-20P cord for Canada
Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight
TQ-1800 208
60 4440
21.4
NEMA 6-30P 73 lbs. (33 kg)
240 18.5
TQ-1800H 208
60 4650
22.4
NEMA 6-30P 73 lbs. (33 kg)
240 19.4
TQ-1800BA 208
60 4580
22.0
NEMA 6-30P 73 lbs. (33 kg)
240 19.1
TQ-1800HBA 208
60 4580
22.0
NEMA 6-30P 73 lbs. (33 kg)
240 19.1
Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight
TQ-1200
208
60 4030
19.4
NEMA 6-30P 65 lbs. (30 kg)
240
16.8
Electrical Rating Chart — Model TQ-1200
Electrical Rating Chart — TQ-1800 Models
8
Form No. TQ2M-1219
English
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
TQ-10
14-1/2
(368 mm)
17-3/4
(451 mm)
13-3/4
(349 mm)
13-1/8
(333 mm)
13-3/8
(340 mm)
SPECIFICATIONS
Dimensions — Model TQ-10
Front View Side View
A
D E
C
B
Form No. TQ2M-1219
9
English
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
TQ-400
14-1/2
(368 mm)
17-3/4
(451 mm)
14-7/8
(378 mm)
12-3/8
(314 mm)
11-5/8
(295 mm)
TQ-405
14-1/2
(368 mm)
17-3/4
(451 mm)
14-7/8
(378 mm)
12-3/8
(314 mm)
11-5/8
(295 mm)
TQ-400H
14-1/2
(368 mm)
17-3/4
(451 mm)
15-7/8
(403 mm)
12-3/8
(314 mm)
11-5/8
(295 mm)
TQ-400BA
14-1/2
(368 mm)
17-3/4
(451 mm)
14-7/8
(378 mm)
12-3/8
(314 mm)
11-5/8
(295 mm)
TQ-800
14-1/2
(368 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
12-3/8
(314 mm)
13-1/2
(344 mm)
TQ-805
14-1/2
(368 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
12-3/8
(314 mm)
13-1/2
(344 mm)
TQ-800H
14-1/2
(368 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
12-3/8
(314 mm)
13-1/2
(344 mm)
TQ-800BA
14-1/2
(368 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
12-3/8
(314 mm)
13-1/2
(344 mm)
TQ-800HBA
14-1/2
(368 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
12-3/8
(314 mm)
13-1/2
(344 mm)
TQ-1200
14-1/2
(368 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
12-3/8
(314 mm)
13-1/2
(344 mm)
TQ-1800
18-1/2
(470 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
16-3/8
(416 mm)
13-1/2
(344 mm)
TQ-1800H
18-1/2
(470 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
16-3/8
(416 mm)
13-1/2
(344 mm)
TQ-1800BA
18-1/2
(470 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
16-3/8
(416 mm)
13-1/2
(344 mm)
TQ-1800HBA
18-1/2
(470 mm)
22-3/4
(578 mm)
16-5/8
(422 mm)
16-3/8
(416 mm)
13-1/2
(344 mm)
SPECIFICATIONS
Dimensions — TQ-400, -405, -400H, -800, -805, -1200, and -1800 Models
)URQW9LHZ 6LGH9LHZ
$ %
' (
&
10
Form No. TQ2M-1219
English
INSTALLATION
General
Hatco Toast-Qwik
®
Conveyor Toasters are shipped with most
components pre-assembled. Care should be taken when
unpacking the shipping carton to avoid damage to the unit and
the components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 70°F (21°C) and a maximum of 85°F (29°C).
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
FIRE HAZARD:
• Do not locate toaster under shelving or closer than 12″
(305 mm) from the ceiling.
• Do not place anything on top of toaster. Do not
place toaster near or underneath curtains or other
combustible materials. Items near or on top of toaster
could catch fire causing injury and/or damage to the
toaster.
1. Remove the unit from the carton.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of the unit.
CAUTION
Locate unit at the proper counter height in an area that is
convenient for use. Location should be level and strong
enough to support weight of unit and contents.
NOTICE
Do not locate unit in an area subject to temperatures above
85°F (29°C) or grease from grills, fryers, etc. Excessive
temperatures and grease could cause damage to unit.
3. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and between 70°F (21°C) and
85°F (29°C). Avoid areas that may be subject to active
air movements or currents (i.e., near exhaust fans/
hoods and air conditioning ducts).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
4. Level the unit by turning the leveling feet on each leg, if
necessary.
5. Install the front or rear discharge chutes. Refer to the
“Front or Rear Discharge Installation” procedure in this
section.
Crumb
Tray
Toast Collector
Pan
Discharge Chute
Components
CAUTION
Always operate toaster with crumb tray installed.
6. Install the crumb tray.
a. Position the crumb tray directly below the stop pins
under the conveyor belt at the front of the toaster.
b. Slide the crumb tray into the toaster until the front of the
crumb tray meets the stop pins.
Stop Pins
Crumb
Tray
Installing the Crumb Tray
Form No. TQ2M-1219
11
English
Front or Rear Discharge Installation
Toast-Qwik units can be set up so toasted product discharges
at either the front or the rear of the unit.
WARNING
FIRE HAZARD:
• For front discharge operation: Allow a minimum
clearance of 1″ (25 mm) along the sides and rear of
unit. Allow a minimum clearance of 12″ (305 mm) in the
front. If safe distances are not maintained, discoloration
or combustion could occur.
• For rear discharge operation: Allow a minimum
clearance of 1″ (25 mm) along the sides of unit. Allow
a minimum clearance of 12″ (305 mm) in the front and
rear. If safe distances are not maintained, discoloration
or combustion could occur.
Model TQ-10
Model TQ-10 uses a one piece discharge chute/collector pan.
The installation location determines the discharge area.
For front discharge:
• Slide the toaster chute into the toaster from the front of the
toaster with the rear lip of the chute on the rear most pins.
Rear
Pin
TQ-10 Front Discharge
For rear discharge:
• Slide the toaster chute into the toaster from the rear of the
toaster with the lip of the chute over the inside set of pins.
Pin
TQ-10 Rear Discharge
TQ-400, -800, -1200, and -1800 Series
TQ-400, -800, -1200, and -1800 series toasters use a separate
discharge chute and toast collector pan. The installation
location determines the discharge area.
For front discharge:
1. Install the discharge chute.
• Place the curved end inward until the rear lip of the
chute is on the rear chute pins.
• Lower the front slots of the chute onto the front chute
pins.
2. Position the toast collector pan, with the open end in first,
over the pan pins.
• Align the slanted notches over the pan pins and lower
into place.
Toast Collector Pan
Discharge Chute
Pan
Pins
Front Chute
Front Chute
Pin
Pin
Front Chute
Pin
Rear Chute
Pin
TQ-400, -800, -1200, and -1800 Series Front Discharge
For rear discharge:
1. Remove the discharge chute if it is installed. It is not used
for rear discharge.
2. Slide the toast collector pan, with the open end first, over
the set of pan pins at the rear of the unit.
• Align the slanted notches over the two sets of rear pan
pins and lower into place.
Toast Collector Pan
Rear
Pan Pins
TQ-400, -800, -1200, and -1800 Series Rear Discharge
INSTALLATION
12
Form No. TQ2M-1219
English
OPERATION
Control Panel – TQ-10 Series
General
Toast-Qwik
®
Conveyor Toasters are designed for ease of
operation. To operate the toaster, perform the appropriate
procedure in this section.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Do not remove crumb tray for cleaning until toaster is
cool.
Always operate toaster with crumb tray installed.
Toasting of coated or buttered products such as garlic
bread, cheese sandwiches, and sweet rolls is NOT
recommended. Residue will reduce toaster performance
and could ignite inside toaster. Using toaster with food
products listed above will void unit warranty.
ColorGuard System
All TQ-400, -800, -1200, and -1800 series toasters use a
patented ColorGuard Sensing System that monitors and
automatically adjust conveyor speed during high usage
periods to assure toast color uniformity.
NOTE: The ColorGuard Sensing System is inoperable for
approximately ten minutes after any heat adjustments
are made.
Operating Model TQ-10
1. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
2. Move the feed ramp to the desired position. Refer to
“Adjusting the Toast Feed Ramp” in this section for details.
3. Move the Top Heat ( ) and/or Bottom Heat ( ) switches
to the I (on) position.
• For two-sided toasting, place the and switches in
the I (on) position.
• For top-sided toasting, place the switch in the I (on)
position and the switch in the O (off) position.
• For bottom-sided toasting, place the switch in the O
(off) position and the switch in the I (on) position.
4. Turn the Color Control to the lowest position ( ) while the
unit heats up.
NOTE: Allow approximately 15 to 20 minutes for a warm-up period.
5. After warm-up period, set the Color Control to the medium
position and toast two slices of bread product then re-
adjust the Color Control to the desired setting.
NOTE: To toast moist products such as English muffins, rye
bread, or whole wheat, slow the conveyor by turning the
Color Control knob to a darker setting (clockwise).
Form No. TQ2M-1219
13
English
OPERATION
Control Panel – TQ-400, -800, -1200, and -1800 Series, Single-Sided Toaster
Power I/O
(on/off) Switch
Color Control
Top Heat
Control
Warning
Light
Power Save
Button
Bottom Heat
Control
Control Panel – TQ-400, -800, -1200, and -1800 Series, Two-Sided Toaster
Power I/O
(on/off) Switch
Color Control
Top Heat
Control
Warning
Light
Power Save
Button
Bottom Heat
Control
Operating TQ-400, -800, -1200, and -1800
Series
1. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
2. Move the Power I/O (on/off) switch in the I (on) position.
3. Adjust the Top Heat ( ) and/or Bottom Heat ( ) controls.
• For two-sided toasting, turn the control and control
clockwise to the highest setting.
• For one-sided toasting, turn the control clockwise
to the highest setting and turn the control counter-
clockwise to the lowest setting.
NOTE: TQ-400BA, -800BA, -800HBA, -1800BA, and -1800HBA
toasters are designed specifically for toasting one side
of a bread product, such as a bun or bagel. These
models toast with the cut side facing up.
NOTE: When toasting a single-sided product such as a bun
or bagel, place the product with the cut side facing up.
Adjust the Bottom Heat control to a light setting, toast
two slices of bread product and adjust the Top Heat
and/or Bottom Heat controls as needed.
4. Turn the Color Control to the lowest position ( ) while the
toaster heats up.
NOTE: Allow approximately 15 to 20 minutes for a warm-up
period.
5. After warm-up period, toast two slices of bread product.
Adjust the Color Control if needed.
NOTE: If toasted bread product is too dark with the Color
Control set on the lightest setting, adjust the Top Heat
and/or Bottom Heat controls as needed. (Allow 15 to
20 minutes for toaster to re-adjust to new setting before
resuming operation.)
NOTE: To toast moist products such as English Muffins, rye
bread or whole wheat, slow the conveyor by turning the
Color Control knob to a darker setting (clockwise).
IMPORTANT NOTE
If the Warning light comes on, the unit may be overheating.
Turn off and unplug the unit. Refer to the “Daily Cleaning”
procedure to clean the cooling fan vents. If the unit does
not function properly after cleaning the cooling fan vents,
contact an Authorized Service Agent or Hatco for assistance.
14
Form No. TQ2M-1219
English
OPERATION
Power Save Mode with Indicator Light
All TQ-400, -800, -1200, and -1800 series toasters have a
built-in Power Save Mode with Indicator light feature. This
feature reduces power to the heating elements by 50 percent.
During Power Save Mode the indicator light on the Power Save
( ) button will flash.
To activate Power Save Mode:
1. Press the button until the indicator light flashes.
To exit Power Save Mode:
1. Press the button or turn any knob until the indicator light
stops flashing.
NOTE: Allow a minimum of 2–3 minutes before toasting. Unit is
back up to full power within 10 minutes.
Adjusting the Toast Feed Ramp
The toast feed ramp is installed at the factory and can be used
in two positions.
Automatic Feed Position
For automatic feed, the toast feed ramp should be in an upright
position. Bread products enter the toaster by placing them on
the feed ramp and releasing.
Manual Feed Position
For manual feed, the toast feed ramp should be in a horizontal
position on top of the toaster. Bread products are manually
loaded by placing directly on the conveyor belt.
Automatic Feed
Position
Manual Feed
Position
Toast Feed Ramp
Form No. TQ2M-1219
15
English
MAINTENANCE
General
Hatco Toast-Qwik
®
Conveyor Toasters are designed
for maximum durability and performance with minimum
maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing maintenance, cleaning,
setup, or attempting to clear a jam.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Daily Cleaning
To preserve the finish of the unit, it is recommended that the metal
surfaces be wiped daily with a damp cloth.
WARNING
Submerging or saturating unit with water will damage the
unit and void unit warranty.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and empty the crumb tray and the toast collector
pan.
a. Wash the crumb tray and the toast collector pan with
warm water and a mild detergent. Rinse with water.
b. Allow the crumb tray and toast collector pan to air dry, or
dry with a soft cloth.
CAUTION
BURN HAZARD: Do not remove crumb tray for cleaning
until toaster is cool.
3. Wipe the exterior surfaces of the toaster with a non-
abrasive, damp cloth.
4. Stubborn stains may be removed with a good stainless
steel cleaner or a non-abrasive cleaner. Hard to reach
areas should be cleaned with a small brush and mild soap.
NOTE: The conveyor gear motor and conveyor system are
permanently lubricated and require no lubrication.
5. Check the cooling fan vents and clean any debris
NOTE: TQ-400, -800, -1200, and -1800 series toasters are
equipped with a cooling fan directly below the control
panel area. Check/clean the cooling fan vents monthly
or anytime the Warning light illuminates. For excessive
buildup, use a vacuum cleaner to clear the vents.
Clogged vents will cause the toaster to overheat and
shut down.
Cooling Fan
Vents
Warning
Light
Cooling Fan Vents (TQ-400 shown)
6. Reinstall the crumb tray and toast collector pan. Refer to
the INSTALLATION section for instructions.
Cleaning the Toast Feed Ramp
1. Remove the toast feed ramp by pressing in the two wire
spokes and lifting.
2. Wipe clean with a non-abrasive, damp cloth or soak the
ramp in a mild solution of 1 cup (227 mL) ammonia and
1 gallon (3.785 L) of water.
3. Reinstall the toast feed ramp by aligning the wire spokes
with the holes in the toaster.
Cleaning the Bottom Element Reflector
The bottom heating element reflector inside the toasting
chamber has slots that allow bread crumbs to drop through to
the crumb tray. Over an extended period of use, bread crumbs
may build up on the reflector and not drop through onto the tray.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Wipe the crumbs onto the crumb tray using a bristle brush.
• To wipe the reflector, place the bristle brush through the
conveyor belt and wipe to each side.
3. Perform the “Daily Cleaning” procedure in this section.
16
Form No. TQ2M-1219
English
Symptom Probable Cause Corrective Action
Toast too light. Color Control knob set on a light setting. Turn Color Control knob to a darker setting.
Supply voltage to unit is low. Verify the supply voltage to the toaster matches the unit
specifications.
Toast too dark. Color Control knob set on a dark setting. Turn Color Control knob to a lighter setting.
Supply voltage to unit is high. Verify the supply voltage to the toaster matches the unit
specifications.
Unit takes too long to toast. The first few batches can take longer because
the toaster needs time to heat up when initially
turned on.
Allow toaster to heat up to full operating temperature before
inserting bread product (approximately 15–20 minutes).
Supply voltage to unit is low. Verify the supply voltage to the toaster matches the unit
specifications.
Unit toasts on one side only. Toaster is a “buns” only model. (Model contains
BA in model name.)
Unit is designed to perform in this way.
Bottom Heat or Top Heat Control set too low. Turn the Bottom Heat or Top Heat control to a higher setting.
Heating element defective. Visually check the heating element inside the toaster during
operation. The heating element should glow red. If the
element does not glow, Contact Authorized Service Agent
or Hatco for assistance.
Toaster trips the circuit
breaker or GFCI.
Circuit breaker is not sized properly for the
toaster.
Check circuit breaker for proper sizing.
Wiring fault inside toaster. Contact Authorized Service Agent or Hatco for assistance.
Toaster conveyor doesn’t
move.
Bread slices or buns jammed in conveyor
track.
Turn off unit, wait for unit to cool, and remove bread product
jamming the conveyor.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, setup, or maintenance.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: [email protected]
Form No. TQ2M-1219
17
English
OPTIONS AND ACCESSORIES
Security Cover
The lockable security cover flips up and down to limit access
to the control panel.
1. Remove the crumb tray.
2. Remove the two front screws on the platform above the
controls.
3. Position the security cover over the control panel, aligning
the mounting holes on the security cover with the screw
holes on the platform.
4. Reinstall the two screws through the security cover and
into the platform. Tighten securely.
5. Reinstall the crumb tray.
Extended Feed Guide

feed ramp (not available for TQ-1800 models).
Automatic Power Save Mode
The optional automatic power Save mode feature switches to
power save mode after 30 minutes of inactivity (not available
for TQ-10 models).
30 Amp Cord (TQ-800 Models)
An optional 30 Amp cord (NEMA 6-30P plug) is available for
208 volt TQ-800 models only.
Receptacles
Receptacles are available as accessories for units using
NEMA 5-20P, NEMA 6-20P, or NEMA 6-30P plugs.
Security
Cover
Platform
Lockable security cover
flips up and down.
Platform
Screw
Security Cover
18
Form No. TQ2M-1219
English
LIMITED WARRANTY
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with Hatco’s written instructions
or 18 months from the date of shipment from Hatco. Buyer
must establish the Product’s purchase date by registering the
Product with Hatco or by other means satisfactory to Hatco in
its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part. In
the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT OR
GOODS.
Formulaire n° TQ2M-1219
19
Français
Ce manuel fournit les instructions d’installation, les consignes de
sécurité et le mode d’emploi pour les grille-pain à convoyeur Toast-
Qwik. Hatco vous recommande de lire l’ensemble des instructions
d’installation et d’utilisation et toutes les consignes de sécurité
dans ce manuel avant d’installer et d’utiliser l’appareil.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
INTRODUCTION
Les grille-pain à convoyeur Toast-Qwik
®
Hatco sont conçus
spécialement pour griller le pain plus rapidement. Les produits
destinés à être grillés traversent une chambre chauffée et sont
grillés rapidement et minutieusement. La teneur en humidité,
la teneur en sucre et l’épaisseur du produit de panification
influent sur la capacité à obtenir un produit parfaitement grillé.
La vitesse du convoyeur et la température déterminent la
couleur du pain grillé.
Les grille-pain de Hatco répondent à des normes de qualité
conformes aux exigences du secteur de la restauration et
offrent des performances optimales pendant des années. Les
éléments métalliques chauffants tubulaires sont garantis deux
ans contre toute rupture et panne électrique.
Les grille-pain à convoyeur Toast-Qwik Hatco font l’objet de
recherches approfondies et d’essais. Les matériaux utilisés ont
été sélectionnés pour une durabilité maximale, une apparence
attractive et des performances optimales. Chaque appareil est
soigneusement inspecté et testé avant expédition.
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Informations Importantes pour le Propriétaire ................ 19
Introduction .........................................................................19
Consignes de Sécurité Importantes .................................20
Description du Modèle ....................................................... 21
Désignation du Modèle ......................................................22
Caractéristiques Techniques .............................................23
Configuration des fiches .................................................... 23
Tableau des valeurs nominales électriques ......................23
Dimensions ........................................................................ 25
Installation ...........................................................................27
Généralités ........................................................................27
Installation du système de décharge avant ou arrière ......28
Mode d’emploi ....................................................................29
Généralités ........................................................................29
Fonctionnement du modèle TQ-10 ....................................29
Fonctionnement des séries TQ-400, -800,
-1200, et -1800 ..............................................................30
Mode économie d’énergie et voyant associé .................... 31
Réglage de la rampe d’arrivée du pain .............................31
Maintenance ........................................................................32
Généralités ........................................................................32
Nettoyage quotidien ...........................................................32
Nettoyage de la rampe d’arrivée du pain ..........................32
Nettoyage du réflecteur d’élément inférieur ......................32
Guide de Dépannage ..........................................................33
Options et accessoires ...................................................... 34
Garantie Limitée .................................................................35
Autorisés Distributeurs de Pièces ........Couverture Arrière
Notez le numéro de modèle, le numéro de série, la tension
et la date d’achat de l’appareil dans les espaces ci-dessous
(étiquette des caractéristiques du produit située sur la partie
inférieure gauche de l’appareil). Veuillez avoir cette information
à portée de la main si vous appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage _________________________________________
Date d’achat _____________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
pour faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(Horaires d’été : juin à septembre—
7h00 à 17h00 du lundi au jeudi
7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
SOMMAIRE
20
Formulaire n° TQ2M-1219
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise électriques avec
terre de tension, de format et de configuration des
broches corrects. Si la fiche et la prise électriques
ne se correspondent pas, s’adresser à un électricien
qualifié pour déterminer et installer une prise électrique
de format et de tension corrects.
• Placez l’interrupteur sur OFF (arrêt), débranchez le
cordon d’alimentation, et laissez l’appareil refroidir
avant tout entretien, nettoyage, réglage ou avant de
retirer du pain bloqué.
• L’appareil n’est pas à l’épreuve des intempéries. Placez
l’unité à l’intérieur d’un local dont la température
ambiante se situe entre 21°C (70°F) et 29°C (85°F).
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• Ne pas nettoyer l’appareil lorsqu’il est sous tension.
• Ne renversez pas de liquides dans l’appareil.
• Ne tirez pas l’unité par le cordon d’alimentation.
• Interrompez l’utilisation de l’unité si le cordon
d’alimentation est effiloché ou usé.
• N’essayez jamais de réparer ou de remplacer un cordon
d’alimentation. Celui-ci devra être remplacé par Hatco,
un agent de service agréé par Hatco ou une personne
possédant des qualifications similaires.
• N’insérez jamais un couteau, une fourchette ou un
objet similaire dans la chambre de grillage.
• Ne saisissez pas le grille-pain en introduisant vos
doigts dans l’ouverture d’alimentation.
• Cet appareil doit uniquement être réparé par un personnel
qualifié. Toute réparation par un personnel non qualifié
peut entraîner une électrocution et des brûlures.
• Pour les réparations, utiliser exclusivement des pièces
de rechange Hatco d’origine. Utilisez des pièces
détachées Hatco authentiques sous peine d’annuler
toutes les garanties et d’exposer l’utilisateur à des
tensions électriques dangereuses pouvant entraîner
une électrocution ou des brûlures. Les pièces
de rechange Hatco d’origine sont conçues pour
fonctionner sans danger dans les environnements
dans lesquels elles sont utilisées. Certaines pièces
de rechange génériques ou de second marché ne
présentent pas les caractéristiques leur permettant de
fonctionner sans danger dans la matériel Hatco.
RISQUE D’EXPLOSION : Ne conservez pas ou n’utilisez pas
d’essence ou d’autres vapeurs ou liquides inflammables à
proximité de ces plaques ou de tout autre appareil.
Si le grille-pain surchauffe ou si les ventilateurs de
refroidissement à l’intérieur de l’appareil arrêtent de
fonctionner, l’interrupteur de sécurité haute température
arrêtera le grille-pain. Contacter un agent de service agréé
ou Hatco pour obtenir une assistance.
AVERTISSEMENT
DANGER D’INCENDIE :
• Pour une décharge à l’avant : Laissez une distance
minimale de 25 mm (1″) sur les côtés et à l’arrière de
l’appareil. Laissez un jeu d’au moins 305 mm (12″)
à l’avant. Si ces distances de sécurité ne sont pas
respectées, une décoloration ou une combustion peut
se produire.
• Pour une décharge à l’arrière : Laissez une distance
minimale de 25 mm (1″) sur les côtés de l’appareil.
Laissez une distance minimale de 305 mm (12″) à l’avant
et à l’arrière. Si ces distances de sécurité ne sont pas
respectées, une décoloration ou une combustion peut
se produire.
• Ne placez pas le grille-pain sur une étagère ou à moins
de 305 mm (12″) du plafond.
• Ne posez rien sur le grille-pain. Ne placez pas le grille-
pain à proximité ou en dessous de rideaux ou d’autres
matériaux inflammables. Les éléments situés à proximité
du grille-pain ou sur celui-ci peuvent prendre feu et
entraîner des blessures et/ou endommager le grille-pain.
• En cas d’incendie, débranchez immédiatement le grille-
pain. L’appareil pourra alors refroidir et il sera alors
plus facile et plus sûr d’éteindre l’incendie.
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et correcte de l’appareil.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
ATTENTION
DANGER DE BRÛLURE :
• Certaines surfaces extérieures de l’appareil deviennent
chaudes. Toucher ces zones de l’appareil avec
précaution.
• Retirez le tiroir ramasse-miettes pour le laver
uniquement lorsque le grille-pain est froid.
Placez l’appareil à une hauteur de comptoir adaptée
et sur un emplacement pratique pour son utilisation.
L’emplacement choisi doit être de niveau et solide afin de
supporter le poids de l’appareil et de son contenu.
Utilisez toujours le grille-pain lorsque le tiroir ramasse-
miettes est installé dans l’appareil.
Si le témoin s’allume, l’appareil présente un
dysfonctionnement. Arrêtez l’appareil ou débranchez-le et
faites-le contrôler par un technicien qualifié.
Il est déconseillé de griller des produits enrobés ou
beurrés, comme du pain à l’ail, des tartines au fromage
ou des brioches. Les résidus réduiront la performance du
grille-pain et pourraient l’enflammer. L’utilisation du grille-
pain pour griller les aliments cités précédemment annulera
la garantie de l’appareil.
Lisez l’information de securite importante suivante avant d’utiliser cet équipement pour éviter
des dommages ou la mort sérieux et pour éviter d’endommager l’équipement ou la propriété.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Hatco TQ Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
TQ Series
Catégorie
Grille-pain
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents