Hatco TQ3 Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
TQ3 Series
Catégorie
Grille-pain
Taper
Le manuel du propriétaire
P/N 07.04.800.00 © 2019 Hatco Corporation
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 16)
Toast-Qwik
®
Conveyor Toasters
Grille-pain à convoyeur
TQ3-400, TQ3-500, TQ3-900, TQ3-2000
Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 16
AVERTISSEMENT
2
Form No. TQ3M-0519
English
INTRODUCTION
Hatco TQ3 Series Toast-Qwik
®
Conveyor Toasters are
specially-designed to automate, accelerate, and enhance the
toasting operation. The touchscreen control provides quick,
easy access to menu item presets for the desired product
and toasting color. Product then passes through a heating
chamber for rapid and thorough toasting. Conveyor speed and
temperature determine the toasting color.
Hatco toasters are built with quality to meet the demands
of foodservice operations and provide years of trouble-free
performance. The metal-sheathed tubular heating elements
are guaranteed against breakage and burnout for two years.
Hatco TQ3 Series Toast-Qwik Conveyor Toasters are products
of extensive research and field testing. The materials used
were selected for maximum durability, attractive appearance
and optimum performance. Every unit is thoroughly inspected
and tested prior to shipment.
This manual provides the installation, safety, and operating
instructions for TQ3 Series Toast-Qwik Conveyor Toasters.
Hatco recommends all installation, operating, and safety
instructions appearing in this manual be read prior to installation
or operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Descriptions ..............................................................4
Model Designation ...............................................................5
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Charts ....................................................... 5
Dimensions .......................................................................... 6
Installation .............................................................................7
General ................................................................................ 7
Operation ...............................................................................8
General ................................................................................ 8
Touchscreen Control ............................................................8
Operating the Toaster ..........................................................9
Programming Menu Items .................................................10
PowerSave Mode ..............................................................10
Updating Firmware ............................................................10
Adjusting Automatic PowerSave ....................................... 11
Changing Control Settings ................................................ 11
Maintenance ........................................................................12
General .............................................................................. 12
Daily Cleaning ...................................................................12
Cleaning the Fan Filter ...................................................... 13
Cleaning the Bottom Element Reflector ............................13
Cleaning the Touchscreen Control ....................................13
Troubleshooting Guide ......................................................14
Error Message Guide ........................................................14
Options and Accessories ..................................................15
Limited Warranty ................................................................15
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and purchase
date of the unit in the spaces below (specification label located
on the back of the unit). Please have this information available
when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. _________________________________________
Voltage ___________________________________________
Date of Purchase ___________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00 am to 5:00 pm Monday–Friday,
Central Time (CT)
(Summer Hours — June to September:
7:00 am to 5:00 pm Monday–Thursday
7:00 am to 4:00 pm Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
CONTENTS
Form No. TQ3M-0519
3
English
IMPORTANT SAFETY INFORMATION
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Put unit in standby, allow to cool, turn OFF power switch,
and unplug power cord before performing cleaning,
adjustments, maintenance, or attempting to clear a jam.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C)
and a maximum of 85°F (29°C).
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power cord.
Cord must be replaced by Hatco, an Authorized Hatco
Service Agent, or a person with similar qualifications.
• Never insert a knife, fork, or similar object into toasting
chamber.
• Do not pick up the toaster by inserting fingers into the
toaster feed opening.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some after-market or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
If toaster overheats or cooling fan inside unit stops
working, the safety high-limit switch will shut off toaster.
Contact Authorized Service Agent or Hatco for assistance.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
WARNING
FIRE HAZARD:
• Allow aminimum clearance of1″ (25 mm)along the
sides and rear of unit. Allow a minimum clearance of
12″ (305 mm) in the front, measured from chamber
opening on toaster body. If safe distances are not
maintained, discoloration or combustion could occur.
• Donotlocatetoasterundershelvingorcloserthan12″
(305 mm) from the ceiling.
• Do not place anything on top of toaster. Do not
place toaster near or underneath curtains or other
combustible materials. Items near or on top of toaster
could catch fire causing injury and/or damage to the
toaster.
• In case of fire, disconnect toaster from power source
immediately. This allows unit to cool, making it easier
and safer to put out fire.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Do not remove feed ramp, crumb tray, or toast tray for
cleaning until toaster is cool.
Locate unit at the proper counter height in an area that is
convenient for use. Location should be level and strong
enough to support weight of unit and contents.
Always operate toaster with crumb tray installed.
If Warning light comes on, unit is malfunctioning. Turn
off or disconnect unit from power supply and have unit
serviced by a qualified technician.
Toasting of coated or buttered products such as garlic
bread, cheese sandwiches, and sweet rolls is NOT
recommended. Residue will reduce toaster performance
and could ignite inside toaster. Using toaster with food
products listed above will void unit warranty.
NOTICE
Plug unit into a dedicated circuit. Do not use multiple
appliances on same circuit.
Do not locate unit in an area subject to temperatures above
85°F (29°C) or grease from grills, fryers, etc. Excessive
temperatures and grease could cause damage to unit.
Do not locate toaster in an area that restricts air flow
around front or rear of unit. Do not locate toaster in direct
discharge path of air conditioning vent or makeup air vent.
Damage to any countertop material caused by heat
generated from Hatco equipment is not covered under
the Hatco warranty. Contact manufacturer of countertop
material for application information.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
4
Form No. TQ3M-0519
English
IMPORTANT SAFETY INFORMATION
MODEL DESCRIPTIONS
All Models
All TQ3 Series Toast-Qwik
®
Conveyor Toasters are fast, reliable,
and versatile. The touchscreen control allows pre-programming
of 12 custom menu items for quick and easy selection during
operation. All TQ3 Series conveyor toasters include a toast feed
ramp, a removable crumb tray, a removable fan filter, a USB port,
and a factory attached 6′ (1829 mm) power cord and plug.
PowerSave Mode
TQ3 Series Conveyor Toasters feature an energy-saving
PowerSave mode that reduces heat levels to a specified
percentage of full power. The toaster enters PowerSave mode
automatically after a specified period of inactivity or when the
PowerSave ( ) icon on the touchscreen control is touched.
Full power to the toaster is restored immediately by touching
the icon, and toasting can resume.
During recovery from PowerSave mode, the ColorGuard
system will slow down the conveyor speed for consistent toast
color. Full conveyor speed will be achieved in approximately 10
minutes, depending on how much the heat output level of the
elements was reduced during PowerSave mode.
ColorGuard System
All TQ3 series Conveyor Toasters use a patented ColorGuard
sensing system. The ColorGuard sensing system monitors
and adjusts conveyor speed and chamber temperature
automatically during high usage periods and recovery from
PowerSave mode for consistent toast color.
Model TQ3-400
Model TQ3-400 is a two-slice toaster that allows for toasting
of bread products up to 1-3/4″ (44 mm) thick and 9-5/8″
(244 mm) wide. It has a maximum capacity of approximately 6
bread products per minute. Model-specific features include a
removable toast tray.
USB
Port
Crumb
Tray
Touchscreen
Control
Removable
Toast Tray
Toast Feed
Ramp
Model TQ3-400 Conveyor Toaster
Model TQ3-500
Model TQ3-500 is a two-slice toaster that allows for toasting
of bread products up to 1-3/4″ (44 mm) thick and 9-5/8″
(244 mm) wide. It has a maximum capacity of approximately
8 bread products per minute. Model-specific features include
a removable toast slide, an expandable toast tray, and a over-
temperature warning light.
Model TQ3-500H
Model TQ3-500H includes the same features as model
TQ3-500, but has a 3″ (76 mm) high opening allowing for the
toasting of food items up to 2-3/4″ (70 mm) thick.
Expandable
Toast Tray
USB
Port
Crumb
Tray
Touchscreen
Control
Warning
Light
Toast
Slide
Toast Feed
Ramp
Model TQ3-500 Conveyor Toaster
Model TQ3-900
Model TQ3-900 is a two-slice toaster that allows for toasting
of bread products up to 1-3/4″ (44 mm) thick and 9-5/8″
(244 mm) wide. It has a maximum capacity of approximately
15 bread products per minute. Model-specific features include
a removable toast slide, an expandable toast tray, and an over-
temperature warning light.
Model TQ3-900H
Model TQ3-900H includes the same features as model
TQ3-900, but has a 3″ (76 mm) high opening allowing for the
toasting of food items up to 2-3/4″ (70 mm) thick.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
NOTICE
This unit is intended for commercial use only — NOT for
household use.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Form No. TQ3M-0519
5
English
Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight
TQ3-400 120 50/60 1780 14.8 NEMA 5-15P * 46 lbs. (21 kg)
TQ3-500
TQ3-500H
208
50/60 2220
10.7
NEMA 6-15P † 54 lbs. (25 kg)
240 9.3
TQ3-900
TQ3-900H
208
50/60 3020
14.5
NEMA 6-20P †
50 lbs. (23 kg)
240 12.6 55 lbs. (25 kg)
TQ3-2000
TQ3-2000H
208
50/60 4020
19.3
NEMA 6-30P 60 lbs. (27 kg)
240 16.8
MODEL DESCRIPTIONS
T Q 3 - x x x x H
Toast-Qwik Conveyor Toaster
with Touchscreen Control
Model Number
H = Opening height is 3″ (76 mm)
No Character = Opening height is 2″ (51 mm)
* NEMA 5-20P plug required for Canada.
† Optional NEMA 6-30P plug available.
NOTE: Shipping weight includes packaging.
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug. Plugs are supplied according to the application.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install proper voltage and size electrical receptacle.
NOTE: Receptacles are not supplied by Hatco, but are
available as accessories.
NOTE: Specification label located on the back of the unit. See
label for serial number and verification of unit electrical
information.
1(0$3
1(0$3
1(0$3
1(0$31(0$3
Plug Configurations
Electrical Rating Chart
SPECIFICATIONS
Model TQ3-2000
Model TQ3-2000 is a three-slice toaster that allows for toasting
of bread products up to 1-3/4″ (44 mm) thick and 13-3/4″
(348 mm) wide. It has a maximum capacity of approximately
30 bread products per minute. Model-specific features include
a removable toast slide, an expandable toast tray, and an over-
temperature warning light.
Model TQ3-2000H
Model TQ3-2000H includes the same features as model
TQ3-2000, but has a 3″ (76 mm) high opening allowing for the
toasting of food items up to 2-3/4″ (70 mm) thick.
MODEL DESIGNATION
6
Form No. TQ3M-0519
English
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
Opening
Height (F)
Opening
Width (G)
TQ3-400
14-3/4″
(373 mm)
20-5/8″
(524 mm)
17-3/16″
(435 mm)
13-1/8″
(333 mm)
11-1/16″
(281 mm)
2″
(51 mm)
10-1/16″
(256 mm)
TQ3-500
14-3/4″
(373 mm)
20-5/8″
(524 mm)
17-3/16″
(435 mm)
13-1/8″
(333 mm)
11-1/16″
(281 mm)
2″
(51 mm)
10-1/16″
(256 mm)
TQ3-500H
3″
(76 mm)
TQ3-900
14-3/4″
(373 mm)
20-5/8″
(524 mm)
17-3/16″
(435 mm)
13-1/8″
(333 mm)
11-1/16″
(281 mm)
2″
(51 mm)
10-1/16″
(256 mm)
TQ3-900H
3″
(76 mm)
TQ3-2000
18-3/4″
(475 mm)
21-1/8″
(536 mm)
17-3/16″
(435 mm)
16-9/16″
(520 mm)
11-1/16″
(281 mm)
2″
(51 mm)
14-1/8″
(359 mm)
TQ3-2000H
3″
(76 mm)
SPECIFICATIONS
Dimensions
Front View
Top View
Side View
A
G
D
E
C
B
Specification
Label
F
Model TQ3-500 shown.
Form No. TQ3M-0519
7
English
INSTALLATION
General
Hatco Toast-Qwik
®
Conveyor Toasters are shipped with most
components pre-assembled. Care should be taken when
unpacking the shipping carton to avoid damage to the unit and
the components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 70°F (21°C) and a maximum of 85°F (29°C).
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
FIRE HAZARD:
• Allow aminimum clearance of1″ (25 mm)along the
sides and rear of unit. Allow a minimum clearance of
12″ (305 mm) in the front, measured from chamber
opening on toaster body. If safe distances are not
maintained, discoloration or combustion could occur.
• Donotlocatetoasterundershelvingorcloserthan12″
(305 mm) from the ceiling.
• Do not place anything on top of toaster. Do not
place toaster near or underneath curtains or other
combustible materials. Items near or on top of toaster
could catch fire causing injury and/or damage to the
toaster.
• In case of fire, disconnect toaster from power source
immediately. This allows unit to cool, making it easier
and safer to put out fire.
CAUTION
Locate unit at the proper counter height in an area that is
convenient for use. Location should be level and strong
enough to support weight of unit and contents.
NOTICE
Plug unit into a dedicated circuit. Do not use multiple
appliances on same circuit.
Do not locate unit in an area subject to temperatures above
85°F (29°C) or grease from grills, fryers, etc. Excessive
temperatures and grease could cause damage to unit.
Do not locate toaster in an area that restricts air flow
around front or rear of unit. Do not locate toaster in direct
discharge path of air conditioning vent or makeup air vent.
1. Remove the unit from the carton.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of the unit.
3. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and between 70°F (21°C) and
85°F (29°C). Avoid areas that may be subject to active
air movements or currents (i.e., near exhaust fans/
hoods, air conditioning ducts, and exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level, made of non-
combustible material, and strong enough to support the
weight of the unit and its contents.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
CAUTION
Always operate toaster with crumb tray installed.
4. For TQ3-400 models: Install the removable toast tray
underneath the discharge area.
Removable
Toast Tray
Installing the Toast Tray (Model TQ3-400 only)
8
Form No. TQ3M-0519
English
OPERATION
General
Toast-Qwik
®
Conveyor Toasters are designed for ease of
operation. To operate the toaster, perform the appropriate
procedure in this section.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Do not remove crumb tray for cleaning until toaster is
cool.
Always operate toaster with crumb tray installed.
Toasting of coated or buttered products such as garlic
bread, cheese sandwiches, and sweet rolls is NOT
recommended. Residue will reduce toaster performance
and could ignite inside toaster. Using toaster with food
products listed above will void unit warranty.
Touchscreen Control
The following are descriptions of the controls used to operate
TQ3 Series Toast-Qwik Conveyor Toasters. All controls are
located on the touchscreen control at the front of the unit.
NAME
NAME NAME
1/3
NAME
Menu Item Icons
Touch arrow to
scroll between
screens.
Indicates the
screen number
(first of three).
Lighter/
Darker
Icon
PowerSave
Icon
Service
Icon
Standby
Icon
Touchscreen Control (showing the Menu screen)
Menu Item Icons
Each menu item icon stores the toast settings for a custom
menu item. Touching one of the menu item icons will adjust the
element and conveyor belt settings to the selected menu item.
There are 12 customizable menu item icons available on the
touchscreen control. Refer to “Programming a Menu Item” in
this section to change or create custom menu items.
NOTE: When programming menu items, set up the most used
menu items on the first Menu screen (screen 1/3).
Lighter/Darker Icon
The Lighter/Darker ( ) icon allows the toasting shade to be
changed from the current menu item setting at any time during
operation.
To use the icon:
a. Place the item on the conveyor, and touch the desired
menu item icon.
b. Touch the icon on the touchscreen. The Toast Shade
screen will appear.
c. Touch either the or icon up to five times to produce
toasting shades lighter or darker than the current menu
item setting.
PowerSave Icon
Touching the PowerSave ( ) icon puts the toaster into
PowerSave mode. In PowerSave mode, the toaster remains
activated but the conveyor stops and the heat level drops to a
reduced percentage of the current heat settings.
NOTE: During recovery from PowerSave mode, the
ColorGuard system will slow down the conveyor speed
for consistent toast color. Full conveyor speed will be
achieved in approximately 10 minutes, depending on
how much the heat output level of the elements was
reduced during PowerSave mode.
Service Icon
The Service ( ) icon provides access to the password-
protected Service screen. The Service screen allows
management and service technicians to access specific toaster
settings, diagnostic/service information, and software update
functions.
Standby Icon
The Standby ( ) icon toggles the toaster between operation
and standby. In standby, the conveyor and elements are off and
the touchscreen control display is dark, but the toaster remains
energized.
• From standby, touch and hold the icon for three
seconds to activate the toaster. The toaster will be ready
for operation in approximately ten minutes.
• From operation, touch and hold the icon for three
seconds to shut down operation and put the toaster into
standby.
Form No. TQ3M-0519
9
English
OPERATION
Operating the Toaster
Startup
1. Plug the unit into a properly grounded electrical receptacle.
Make sure the electrical receptacle matches the plug on the
unit and the supply voltage matches the unit specification
label.
2. Move the toast feed ramp to the desired position.
• For automatic feeding, move the toast feed ramp to
the automatic feed position. Bread products enter the
toaster by placing them on the toast feed ramp and
releasing.
• For manual feeding, rotate the toast feed ramp up until
it rests on top of the unit. Bread products can be loaded
manually by placing directly on the conveyor belt.
Automatic
Feed Position
Manual
Feed Position
Toast Feed Ramp
3. Move the Power I/O switch located
on the back of the unit to the “I” (on)
position.
• Logo and software version
information will appear on the
touchscreen, followed by the
Standby screen.
NOTE: If the touchscreen goes dark
after turning on the power, touch anywhere on the
touchscreen to “wake up” the display.
TQ3-900H
SWTQ900HHA0113
Unit is off
Cooling fan may still operate
4. Touch and hold the icon on the
touchscreen for three seconds to
activate the toaster.
• The preheating cycle will begin
and last approximately 10
minutes. When preheating is
complete, the conveyor belt will
start moving, and the Menu screen will appear showing
the available menu items.
NAME
NAME NAME
1/3
NAME
5. Touch the desired menu item icon
on the touchscreen.
• A blue square will outline the
selected menu item.
• The elements and conveyor
belt will adjust settings to the
selected menu item.
• Use the blue arrow keys to scroll between screens of
available menu items.
Expandable
Toast Tray
USB
Port
Crumb
Tray
Touchscreen
Control
Warning
Light
Toast
Slide
Toast Feed
Ramp
Model TQ3-500 Conveyor Toaster
6. Place bread product onto the toast feed ramp.
Lock On Off
7. Change the toasting shade at any
time during toasting. To change:
a. Touch the icon. The Toast
Shade screen will appear.
b. Touch the or icon up to
five times to produce a shade
lighter or darker than the current menu item setting.
8. Change the selected menu item at any time by touching
the desired menu item icon on the touchscreen.
• Use the blue arrow keys to scroll between screens of
available menu items.
NOTE: For TQ3-500, TQ3-900, and TQ3-2000 models: If the
Warning light on the control panel comes on, the unit
may be overheating due to fan failure/blockage. Turn
off and unplug the unit. Contact an Authorized Service
Agent or Hatco for assistance.
Standby Shutdown
Use standby shutdown to put the toaster in standby during
extended periods of non-use.
TQ3-900H
SWTQ900HHA0113
Unit is off
Cooling fan may still operate
1. Touch and hold the icon on the
touchscreen for one second to shut
down operation and put the toaster
into standby.
• The heating elements and
conveyor will shut down.
• The cooling fans will run until the unit is cool.
Shutdown
1. Touch and hold the icon on the touchscreen for one
second to shut down operation and put the toaster into
standby.
2. After the cooling fans stop, move the Power I/O switch
located on the back of the unit to the “O” (off) position to
turn off the toaster. NOTICE: Do not turn off unit while
cooling fans are running. Damage to unit may occur.
10
Form No. TQ3M-0519
English
OPERATION
Updating Firmware
Use the following procedure to upload
firmware updates to the toaster from an
external USB drive.
1. Follow the “Startup” procedure
listed previously in this section.
2. Touch the icon on the Menu
Screen. A password screen will
appear.
• Enter the 3-digit password “248”.
The Service screen will appear.
Firmware
Control
Testmode
Version
Usage
PowerSave
Exit
Service
3. Touch FIRMWARE on the Service
screen. The Update Select screen
will appear.
4. Touch FIRMWARE on the Update
Select screen. The Firmware
Update screen will appear.
Firmware
Image
Exit
5. Slide the cover to the side, and
insert the USB drive into the USB
port.
• The USB port is on the front of
the unit, underneath and to the
right of the touchscreen.
6. Touch UPDATE.
Exit
Update
Firmware Update
Plug-in the USB stick then
press the Update button.
• The firmware update
will begin and last
approximately 30 seconds
(a progress bar will appear).
NOTICE: Do not remove the
USB drive or turn off the unit
during a software update.
• When the update is complete, the unit will restart and
the Logo screen will appear for a few seconds showing
the new firmware version.
7. Remove the USB drive from the USB port, and slide the
cover back to cover the port.
Programming Menu Items
Use the following procedure to change or create custom menu
item settings.
1. Touch and hold the desired menu item on the Menu Screen
for three seconds.
Top Heat
Name
75
%
Btm Heat
75
%
Toast Time
75
sec
• The Programming screen
will appear showing a list of
programmable settings.
Top Heat: Heat output
level from top elements.
Setting range is 1–100%.
1 = lowest heat/lightest toast.
100 = highest heat/darkest toast.
Btm Heat: Heat output level from bottom elements.
Setting range is 1–100%. 1 = lowest heat/lightest toast.
100 = highest heat/darkest toast.
Time: Total time product is in toasting chamber.
Increasing belt time will slow down conveyor and create
darker product. Decreasing belt time will speed up
conveyor and create lighter product.
2. Touch the or arrow next to the desired setting to
change the setting.
3. To change the menu item picture, touch the picture. A
screen will appear with the available pictures
a. Touch the desired picture. The touchscreen will return to
the Programming screen and show the new picture.
4. To change or edit the menu item name, touch the name. A
keypad screen will appear.
a. Touch the key to delete the current name.
b. Use the keypad to change or update the menu item
name.
c. Touch the key to save the name and return to the
Programming screen.
5. When all programming is done, touch the icon to return
to the Menu screen.
PowerSave Mode
All TQ3 series toasters have a built-in PowerSave mode.
This feature significantly reduces heat levels and energy
consumption when the toaster has not been used for a specified
period of time or when activated by the operator.
To start PowerSave mode manually during operation:
1. Touch the icon on the Menu screen.
Powersave Mode
press the leaf
to exit
• The conveyor belt will speed up
temporarily to clear product from
toaster.
• The PowerSave screen will show
on the touchscreen.
To exit PowerSave mode:
1. Touch the icon on the PowerSave screen. The unit will
be ready to toast immediately
NOTE: During recovery from PowerSave mode, the ColorGuard
system will slow down the conveyor speed for consistent
toast color. Full conveyor speed will be achieved in
approximately 10 minutes, depending on how much the
heat output level of the elements was reduced during
PowerSave mode.
Form No. TQ3M-0519
11
English
OPERATION
Adjusting Automatic PowerSave
Use the following procedure to enable/disable the automatic
PowerSave feature as well as make adjustments to its settings.
1. Touch the icon on the Menu Screen. A password
screen will appear.
Firmware
Control
Testmode
Version
Usage
PowerSave
Exit
Service
• Enter the 3-digit password “248”.
The Service screen will appear.
2. Touch POWERSAVE on the
Service screen. The Automatic
PowerSave screen will appear.
3. Make the desired adjustments on
the Automatic PowerSave screen.
Automatic PowerSave
On Off
Heat
47
%
Time
9
mins
EXIT
• Touch ON to enable automatic
PowerSave. Touch OFF to
disable automatic PowerSave.
• Heat: Touch the or arrow
next to the Heat percentage to
change the heat output level of the elements during
PowerSave mode.
• Time: Touch the or arrow next to the Time value
to change the number of minutes of inactivity required
before automatic PowerSave is activated.
4. When all adjustments are done, touch EXIT to return to
the Service screen, then EXIT again to return to the Menu
Screen.
Changing Control Settings
Use the following procedure to make changes to control access
privileges and toaster operation.
1. Touch the icon on the Menu Screen. A password
screen will appear.
Firmware
Control
Testmode
Version
Usage
PowerSave
Exit
Service
• Enter the 3-digit password “248”.
The Service screen will appear.
2. Touch CONTROL on the Service
screen. The Control Settings
screen will appear.
3. Make the desired adjustments on
the Control Settings screen.
Control Settings
On Off
Passcode
On Off
ColorGuard
On Off
Logo
EXIT
• Touch ON or OFF to enable or
disable each of the operational
settings shown on this screen.
• Passcode: Enable this setting
to require a password to make
changes to menu item settings.
• ColorGuard: Disable this setting to turn off the ColorGuard
System, as described in the MODEL DESCRIPTIONS
section of this manual.
• Logo: Enable this setting to put the toaster into a single
setting, “always on” mode.
4. When all changes are done, touch EXIT to return to the
Service screen, then EXIT again to return to the Menu
Screen.
12
Form No. TQ3M-0519
English
General
Hatco Toast-Qwik
®
Conveyor Toasters are designed
for maximum durability and performance with minimum
maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Put unit in standby, allow to cool, turn OFF power
switch, and unplug power cord before performing
cleaning, adjustments, maintenance, or attempting to
clear a jam.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some after-market or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Daily Cleaning
To preserve the finish of the unit, it is recommended that the
metal surfaces be wiped daily with a damp cloth.
WARNING
Submerging or saturating unit with water will damage the
unit and void unit warranty.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Perform the “Daily Shutdown” procedure in the
OPERATION section, and unplug the power cord.
CAUTION
BURN HAZARD: Do not remove feed ramp, crumb tray, or
toast tray for cleaning until toaster is cool.
2. Remove and clean the crumb tray, removable toast tray
(TQ3-400 only), and toast tray insert (if equipped).
a. Wash the crumb tray and toast trays with warm water
and a mild detergent. Rinse with water.
b. Allow the crumb tray and toast trays to air dry.
3. Wipe the exterior surfaces of the toaster with a non-
abrasive, damp cloth.
• Stubborn stains may be removed with a good stainless
steel cleaner or a non-abrasive cleaner. Hard to reach
areas should be cleaned with a small brush and mild
soap.
4. Clear all crumbs from the expandable toast tray and wipe
clean.
5. Wipe dry the entire unit using a soft, non-abrasive cloth.
6. Reinstall the crumb tray, removable toast tray (TQ3-400
only), and toast tray insert (if equipped).
a. Position the crumb tray directly below the conveyor belt
on the tray floor at the front of the toaster.
b. Slide the crumb tray into the toaster until it stops.
7UD\
)ORRU
&UXPE7UD\
Installing the Crumb Tray
MAINTENANCE
Form No. TQ3M-0519
13
English
MAINTENANCE
Cleaning the Fan Filter
A cooling fan filter is located on the bottom of the unit. This
filter should be checked/cleaned weekly and anytime “Routine
Maintenance; Clean Fan Filter” appears on the touchscreen.
Use the following procedure to clean the filter.
1. Perform the “Shutdown” procedure in the OPERATION
section, and unplug the power cord.
2. Using the filter handle, slide the filter out of the filter
housing.
3. Tilt the unit up and wipe the filter housing clean using a
damp non-abrasive cloth.
4. Rinse the filter using hot water. Allow the filter to dry
completely.
5. Slide the filter back into the filter housing.
NOTE: The filter can be installed from either side of the toaster.
Toast tray removed
for clarity in view
from bottom.
Filter
Housing
Filter
Filter
Handle
Cooling
Fan
Cleaning the Filter
Cleaning the Bottom Element Reflector
The bottom heating element reflector inside the toasting
chamber has slots that allow bread crumbs to drop through to
the crumb tray. Over an extended period of use, bread crumbs
may build up on the reflector and not drop through onto the tray.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Wipe the crumbs onto the crumb tray using a bristle brush.
• To wipe the reflector, place the bristle brush through the
conveyor belt and wipe to each side.
3. Perform the “Daily Cleaning” procedure in this section.
Cleaning the Touchscreen Control
Dirt and grease will build up on the touchscreen control over an
extended period of use. Use the following procedure to clean
the touchscreen control and maintain performance.
1. Perform the “Shutdown” procedure in the OPERATION
section, and unplug the power cord.
2. Spray a mild degreaser onto a soft, damp non-abrasive
cloth, and wipe the entire touchscreen until clean. Repeat,
if necessary.
3. Allow the touchscreen to dry completely.
4. Wipe away any hazy residue that remains on the
touchscreen using a clean, dry non-abrasive cloth.
14
Form No. TQ3M-0519
English
Symptom Probable Cause Corrective Action
Toast too light. Wrong menu item selected on touchscreen
control.
Select the correct menu item for desired toasting results.
Supply voltage to unit is low. Verify the supply voltage to the toaster matches the unit
specifications.
Toast too dark. Wrong menu item selected on touchscreen
control.
Select the correct menu item for desired toasting results.
Supply voltage to unit is high. Verify the supply voltage to the toaster matches the unit
specifications.
Unit toasts on one side only. Wrong menu item selected on touchscreen
control.
Select the correct menu item for desired toasting results.
Heating element defective. Visually check the heating element inside the toaster during
operation. The heating element should glow red. If the
element does not glow, Contact Authorized Service Agent
or Hatco for assistance.
Toaster trips the circuit breaker
or GFCI.
Circuit breaker is not sized properly for the
toaster.
Check circuit breaker for proper sizing.
Wiring fault inside toaster. Contact Authorized Service Agent or Hatco for assistance.
Toaster conveyor doesn’t
move.
Bread slices or buns jammed in conveyor
track.
Turn off unit, wait for unit to cool, and remove bread product
jamming the conveyor.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, setup, or maintenance.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: [email protected]
Error Message Guide
Error Message Troubleshooting
Corrective Action
(if Troubleshooting fails to fix)
Temperature Probe Error Verify wire connections on RTD temperature probe.
Check resistance across probe.
Replace temperature probe.
Control Board Overtemp Check fan for physical blockage that would prevent fan
from turning. Verify voltage to fan. Make sure unit is on
legs and filter area is clear.
Replace cooling fan.
Heating Error Verify all wire connections on relay and element. Check
resistance across failing heating element.
Replace heating element.
Communication Error Update software—download from Hatco website to USB
drive. Follow the “Updating Firmware” procedure in
OPERATION section of manual.
Replace electronic control.
Touch Panel Error Check touchpad for grease and dirt buildup. Perform
“Cleaning the Touchscreen Control” procedure in
MAINTENANCE section on manual.
Replace electronic control.
Form No. TQ3M-0519
15
English
OPTIONS AND ACCESSORIES
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the “Products”)
to be free from defects in materials and workmanship, under
normal use and service, for a period of one (1) year from the
date of purchase when installed and maintained in accordance
with Hatco’s written instructions or 18 months from the date
of shipment from Hatco. Buyer must establish the Product’s
purchase date by registering the Product with Hatco or by other
means satisfactory to Hatco in its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part. In
the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT OR
GOODS.
LIMITED WARRANTY
Extended Toast Feed Ramp
An extended toast feed ramp is available as a factory-installed
option for TQ3-500, TQ3-900, and TQ3-2000 models. The
extended toast feed ramp is a longer feed ramp that allows
more or longer bread products to be loaded onto the toast feed
ramp.
Toast Tray Insert
A removable, stainless steel toast
tray insert is available as a factory-
installed option for TQ3-500,
TQ3-900, and TQ3-2000 models.
The toast tray insert fits inside the
toast tray and is easily removable
for cleaning.
16
Formulaire n° TQ3M-0519
Français
Ce manuel fournit les instructions relatives à l’installation, à
la sécurité et au fonctionnement des grille-pain à convoyeur
Toast-Qwik de la série TQ3. Hatco vous recommande de
lire l’ensemble des instructions d’installation, de sécurité et
d’utilisation fournies dans ce manuel avant d’installer et d’utiliser
l’appareil.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
INTRODUCTION
Tous les modèles de grille-pain à convoyeur Toast-Qwik
®
de la série TQ3 de Hatco sont spécialement conçus pour
automatiser, accélérer et améliorer les opérations de grillage
du pain. Le panneau de commande à écran tactile offre un
accès rapide et simple aux préréglages des rubriques de
menu, afin d’obtenir le produit et la coloration souhaités. Le
produit traverse ensuite une chambre chauffée et est grillé
rapidement et minutieusement. La vitesse du convoyeur et la
température déterminent la couleur du pain grillé.
Les grille-pain de Hatco répondent à des normes de qualité
conformes aux exigences du secteur de la restauration et
offrent des performances optimales pendant des années. Les
éléments métalliques chauffants tubulaires sont garantis deux
ans contre toute rupture et panne électrique.
Les grille-pain à convoyeur Toast-Qwik de la série TQ3
proposés par Hatco sont le fruit de recherches approfondies
et de nombreux tests sur le terrain. Les matériaux utilisés ont
été sélectionnés afin de garantir une durée de vie maximale,
un design attractif et des performances optimales. Chaque
appareil est soigneusement inspecté et testé avant expédition.
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Informations Importantes pour le Propriétaire ................ 16
Introduction .........................................................................16
Consignes de Sécurité Importantes .................................17
Description du Modèle ....................................................... 18
Désignation du Modèle ......................................................19
Caractéristiques Techniques .............................................20
Configuration des fiches .................................................... 20
Tableau des valeurs nominales électriques ......................20
Dimensions ........................................................................ 21
Installation ...........................................................................22
Généralités ........................................................................22
Mode d’emploi ....................................................................23
Généralités ........................................................................23
Panneau de commande à écran tactile.............................23
Fonctionnement du grille-pain ...........................................24
Programmation des rubriques de menu ............................ 25
Mode PowerSave (économie d'énergie) ...........................25
Mise à jour du micrologiciel ............................................... 25
Réglage du mode PowerSave (économie d’énergie)
automatique .....................................................................26
Modification des paramètres de commande .....................26
Maintenance ........................................................................27
Généralités ........................................................................27
Nettoyage quotidien ...........................................................27
Nettoyage du filtre du ventilateur ......................................28
Nettoyage du réflecteur d’élément inférieur ......................28
Nettoyage du panneau de commande avec écran tactile ..28
Guide de Dépannage ..........................................................29
Guide des messages d’erreur ...........................................29
Options et accessoires ...................................................... 30
Garantie Limitée .................................................................31
Autorisés Distributeurs de Pièces ........Couverture Arrière
Notez le numéro de modèle, le numéro de série, la tension
et la date d’achat de l’appareil dans les espaces ci-dessous
(Étiquette des caractéristiques techniques située au dos de
l'appareil). Veuillez avoir cette information à portée de la main
si vous appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage _________________________________________
Date d’achat _____________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
pour faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(Horaires d’été—juin à septembre:
7h00 à 17h00 du lundi au jeudi
7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
SOMMAIRE
Formulaire n° TQ3M-0519
17
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise électriques avec
terre de tension, de format et de configuration des
broches corrects. Si la fiche et la prise électriques
ne se correspondent pas, s’adresser à un électricien
qualifié pour déterminer et installer une prise électrique
de format et de tension corrects.
• Mettez l’appareil en veille, laissez-le refroidir, mettez
l’interrupteur marche-arrêt en position OFF et
débranchez le cordon d’alimentation avant de procéder
au nettoyage, aux réglages, à l’entretien ou avant de
tenter d’enlever le pain coincé dans l’appareil.
• L’appareil n’est pas à l’épreuve des intempéries. Placez
l’unité à l’intérieur d’un local dont la température
ambiante se situe entre 21°C (70 °F) et 29°C (85°F).
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• Ne pas nettoyer l’appareil lorsqu’il est sous tension.
• Ne renversez pas de liquides dans l’appareil.
• Ne tirez pas l’unité par le cordon d’alimentation.
• Interrompez l’utilisation de l’unité si le cordon
d’alimentation est effiloché ou usé.
• N’essayez jamais de réparer ou de remplacer un cordon
d’alimentation. Celui-ci devra être remplacé par Hatco,
un agent de service agréé par Hatco ou une personne
possédant des qualifications similaires.
• N’insérez jamais un couteau, une fourchette ou un
objet similaire dans la chambre de grillage.
• Ne saisissez pas le grille-pain en introduisant vos
doigts dans l’ouverture d’alimentation.
• Cet appareil doit uniquement être réparé par un
personnel qualifié. Toute réparation par un personnel
non qualifié peut entraîner une électrocution et des
brûlures.
• Pour les réparations, utiliser exclusivement des pièces
de rechange Hatco d’origine. Utilisez des pièces
détachées Hatco authentiques sous peine d’annuler
toutes les garanties et d’exposer l’utilisateur à des
tensions électriques dangereuses pouvant entraîner
une électrocution ou des brûlures. Les pièces
de rechange Hatco d’origine sont conçues pour
fonctionner sans danger dans les environnements
dans lesquels elles sont utilisées. Certaines pièces
de rechange génériques ou de second marché ne
présentent pas les caractéristiques leur permettant de
fonctionner sans danger dans la matériel Hatco.
RISQUE D’EXPLOSION : Ne conservez pas ou n’utilisez pas
d’essence ou d’autres vapeurs ou liquides inflammables à
proximité de ces plaques ou de tout autre appareil.
AVERTISSEMENT
DANGER D’INCENDIE :
• Laissezunedistanceminimalede25mm(1″)surles
côtés et à l’arrière de l’appareil. Laissez une distance
minimalede305mm(12″)àl’avant,mesuréàpartirde
l’ouverture de la chambre dans le corps du grille-pain.
Si ces distances de sécurité ne sont pas respectées,
une décoloration ou une combustion peut se produire.
• Ne placez pas le grille-pain sous une étagère ou à
moinsde305mm(12″)duplafond.
• Ne posez rien sur le grille-pain. Ne placez pas le grille-
pain à proximité ou en dessous de rideaux ou d'autres
matériaux inflammables. Les éléments situés à proximité
du grille-pain ou sur celui-ci peuvent prendre feu et
entraîner des blessures et/ou endommager le grille-pain.
• En cas d'incendie, débranchez immédiatement le grille-
pain. L'appareil pourra alors refroidir et il sera alors
plus facile et plus sûr d'éteindre l'incendie.
Si le grille-pain surchauffe ou si les ventilateurs de
refroidissement à l’intérieur de l’appareil arrêtent de
fonctionner, l’interrupteur de sécurité haute température
arrêtera le grille-pain. Contacter un agent de service agréé
ou Hatco pour obtenir une assistance.
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et corr ecte de l’appareil.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
ATTENTION
DANGER DE BRÛLURE :
• Certaines surfaces extérieures de l’appareil deviennent
chaudes. Toucher ces zones de l’appareil avec précaution.
• Retirez la rampe d’arrivée du pain, le tiroir ramasse-
miettes ou le bac à toasts pour les laver uniquement
lorsque le grille-pain est froid.
Placez l’appareil à une hauteur de comptoir adaptée
et sur un emplacement pratique pour son utilisation.
L’emplacement choisi doit être de niveau et solide afin de
supporter le poids de l’appareil et de son contenu.
Utilisez toujours le grille-pain lorsque le tiroir ramasse-
miettes est installé dans l’appareil.
Si le témoin s’allume, l’appareil présente un
dysfonctionnement. Arrêtez l’appareil ou débranchez-le et
faites-le contrôler par un technicien qualifié.
Il est déconseillé de griller des produits enrobés ou
beurrés, comme du pain à l’ail, des tartines au fromage
ou des brioches. Les résidus réduiront la performance du
grille-pain et pourraient l’enflammer. L’utilisation du grille-
pain pour griller les aliments cités précédemment annulera
la garantie de l’appareil.
Lisez les consignes de sécurité importantes suivantes avant d’utiliser cet équipement pour éviter
toute blessure grave ou la mort et pour éviter d’endommager l’équipement ou la propriété.
18
Formulaire n° TQ3M-0519
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
Tous les Modèles
Dans la série TQ3, tous les modèles Toast-Qwik
®
Les grille-pain
à convoyeur sont rapides, fiables et polyvalents. Le panneau
de commande à écran tactile permet de préprogrammer
12 rubriques de menu personnalisées pour une sélection
simple et rapide durant le fonctionnement de l’appareil. Tous
les grille-pain à convoyeur de la série TQ3 sont équipés d’une
rampe d’arrivée du pain, d’un tiroir ramasse-miettes amovible,
d’un filtre de ventilateur amovible, d’un port USB ainsi que
d’uncordon d’alimentation de 1829 mm (6′) et d’une prise
installés en usine.
Mode PowerSave (Économie d’énergie)
Les grille-pain à convoyeur de la série TQ3 possèdent
un mode Économie d’énergie qui permet de réduire
les niveaux de chaleur à un pourcentage spécifié de
la puissance totale. Le grille-pain se met en mode
Économie d’énergie automatiquement après une période
d’inactivité spécifiée ou lorsque vous appuyez sur l’icône
( ) Économie d’énergie du panneau de
commande.L'alimentation du grille-pain est rétablie à son
maximum de façon immédiate en touchant l’icône, et vous
pouvez de nouveau faire griller votre pain.
Pendant la récupération du mode Économie d’énergie, le
système ColorGuard diminuera la vitesse du convoyeur pour
une couleur des toasts uniforme. Le convoyeur atteint sa
vitesse maximale en 10 minutes environ, selon la façon dont le
niveau de sortie de chaleur des éléments a été réduit pendant
le mode Économie d’énergie.
Système ColorGuard
Tous les grille-pain à convoyeur de la série TQ3 utilisent un
système de détection ColorGuard breveté. Le système de
capteurs ColorGuard surveille et règle automatiquement la
vitesse du convoyeur et la température de la chambre pendant
les périodes d’utilisation intensive et la récupération du mode
Économie d’énergie pour une couleur uniforme des toasts.
Modèle TQ3-400
Le modèle TQ3-400 est un grille-pain à deux tranches qui
permet de griller des pains d’une épaisseur maximale de
44 mm (1,73″) et d’une largeur maximale de 244 mm (9,61″).
Sa capacité maximale est d’environ 6 pains par minute. Les
caractéristiques spécifiques du modèle incluent un bac à toasts
amovible.
Port
USB
Bac à
miettes
Panneau de
commande à
écran tactile
Bac à toasts
amovible
Rampe d'arrivée
du pain
Grille-pain à convoyeur modèle TQ3-400
DESCRIPTION DU MODÈLE
AVIS
Branchez l ’appareil à un circuit dédié. Ne branchez pas
plusieurs appareils sur un même circuit.
Ne placez pas l’appareil dans une zone exposée à des
températures supérieures à 29°C (85°F) ou soumise à la
graisse des grils, des friteuses, etc. Des températures
excessives et la graisse risquent d’endommager l’appareil.
Ne placez pas le grille-pain dans une zone qui réduit le
flux d’air autour de l’avant et de l’arrière de l’appareil. Ne
placez pas le grille-pain dans le chemin de déchargement
direct des bouches de ventilation ou des bouches d’air de
compensation.
AVIS
Les dommages à toute partie du comptoir pouvant être
causés par la chaleur générée par l’équipement de Hatco
ne sont pas couverts par la garantie de Hatco. Contactez
le fabricant du comptoir pour obtenir des renseignements.
Utilisez uniquement des nettoyants non abrasifs et des
chiffons doux. Les chiffons et nettoyant abrasifs pourraient
rayer la finition de l’unité, altérant son apparence et la
rendant vulnérable à l’accumulation de saleté.
Cet appareil est réservé à un usage professionnel
uniquement — il ne convient PAS à un usage personnel.
Nettoyez l’unité quotidiennement pour éviter les
dysfonctionnements et assurer un fonctionnement sain.
Formulaire n° TQ3M-0519
19
Français
DESCRIPTION DU MODÈLE
DÉSIGNATION DU MODÈLE
Modèle TQ3-500
Le modèle TQ3-500 est un grille-pain à deux tranches qui
permet de griller des pains d’une épaisseur maximale de
44 mm (1,73″) et d’une largeur maximale de 244 mm (9,61″).
Sa capacité maximale est d’environ 8 pains par minute. Les
caractéristiques spécifiques du modèle incluent une glissière
à toasts amovible, un bac à toasts extensible et un témoin
signalant les surchauffes.
Modèle TQ3-500H
Le modèle TQ3-500H possède les mêmes caractéristiques que
le modèle TQ3-500, mais comprend aussi une ouverture de
76 mm (3″) de haut permettant de griller des aliments d’une
épaisseur de 70 mm (2,76″).
Bac à toasts
extensible
Port
USB
Bac à
miettes
Panneau de commande
à écran tactile
Témoin
Glissière
à toasts
Rampe d'arrivée
du pain
Grille-pain à convoyeur modèle TQ3-500
Modèle TQ3-900
Le modèle TQ3-900 est un grille-pain à deux tranches qui
permet de griller des pains d’une épaisseur maximale de
44 mm (1,73″) et d’une largeur maximale de 244 mm (9,61″).
Sa capacité maximale est d’environ 15 pains par minute. Les
caractéristiques spécifiques du modèle incluent une glissière
à toasts amovible, un bac à toasts extensible et un témoin
signalant les surchauffes.
Modèle TQ3-900H
Le modèle TQ3-900H possède les mêmes caractéristiques que
le modèle TQ3-900, mais comprend aussi une ouverture de
76 mm (3″) de haut permettant de griller des aliments d’une
épaisseur de 70 mm (2,76″).
Modèle TQ3-2000
Le modèle TQ3-2000 est un grille-pain à trois tranches qui
permet de griller des pains d’une épaisseur maximale de
44 mm (1,73″) et d’une largeur maximale de 348 mm (13,7″).
Sa capacité maximale est d’environ 30 pains par minute. Les
caractéristiques spécifiques du modèle incluent une glissière
à toasts amovible, un bac à toasts extensible et un témoin
signalant les surchauffes.
Modèle TQ3-2000H
Le modèle TQ3-2000H possède les mêmes caractéristiques
que le modèle TQ3-2000, mais comprend aussi une ouverture
de 76 mm (3″) de haut permettant de griller des aliments d’une
épaisseur de 70 mm (2,76″).
T Q 3 - x x x x H
Grille-pain à convoyeur Toast-Qwik
avec panneau de commande
à écran tactile
Numéro de modèle
H = Hauteur d'ouverture égale à 76mm (3")
Aucun caractère = la hauteur de l'ouverture
est de 51mm (2")
20
Formulaire n° TQ3M-0519
Français
Modéle Tension Hertz Intensité Amps Configuration de Fiches
Poids
d’embarquement
TQ3-400 120 50/60 1780 14.8 NEMA 5-15P * 21 kg (46 lbs.)
TQ3-500
TQ3-500H
208
50/60 2220
10.7
NEMA 6-15P † 25 kg (54 lbs.)
240 9.3
TQ3-900
TQ3-900H
208
50/60 3020
14.5
NEMA 6-20P †
23 kg (50 lbs.)
240 12.6 25 kg (55 lbs.)
TQ3-2000
TQ3-2000H
208
50/60 4020
19.3
NEMA 6-30P 27 kg (60 lbs.)
240 16.8
CARACTÉRISTIQUES TECHNIQUES
Tableau des valeurs nominales électriques
* Prise NEMA 5-20P pour le Canada.
† Prise NEMA 6-30P disponible.
NOTA: Le poids d’embarquement comprend le matériel d’emballage.
Configuration des fiches
Les appareils sont fournis par l’usine avec un cordon et une
fiche. Les fiches fournies correspondent à leur application.
WARNING
DANGER DE DÉCHARGE ÉLECTRIQUE: Brancher
l’appareil sur une prise électriques avec terre de tension, de
format et de configuration des broches corrects. Si la fiche
et la prise électriques ne se correspondent pas, s’adresser
à un électricien qualifié pour déterminer et installer une
prise électrique de format et de tension corrects.
NOTA: Les prise électriques ne sont pas fournies par Hatco,
mais sont disponibles comme accessoires.
NOTA: Étiquette des caractéristiques techniques située au
dos de l'appareil. Consultez l’étiquette pour connaître
le numéro de série et vérifier les caractéristiques
électriques de l’appareil.
1(0$3
1(0$3
1(0$3
1(0$31(0$3
Configuration des fiches
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Hatco TQ3 Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
TQ3 Series
Catégorie
Grille-pain
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents