DeWalt D55394 Manuel utilisateur

D55394

Contractor’s Electric Wheeled Portable Air Compressor

Compresseur d’air électrique portatif sur roues de classe entrepreneur

Compresor de aire eléctrico portátil con ruedas para contratistas

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-De

2





A. Pump Air Intake Filter

B. Pump Oil Drain Plug

C. On/Off Switch

D. Air Tank Pressure Gauge

E. Regulated Pressure Gauge

F. Pressure Regulator

G. Air Outlet



Inline, vertical twin cylinder

Single stage

Oil lubricated

Cast iron crankcase and cylinder

Bore: 2.756" (70 mm)

Stroke: 2.26" (57.5 mm)

Weight: 46 lbs. (20.86 kg)

Oil Capacity: 24.7 oz. (730 mL)



3.5 HP

230V, 16 A, 60 Hz

Two pole, induction type, 3450 RPM

Minimum branch circuit requirement: 20 A @ 230V

Fuse Type: Time delay

FIG. 1

L

J

NOT A

STEP

200

180

160

140

120

100

80

60

40

20

E

F

G

D

B

H

M

C

K

I

H. Unloader Valve

I. Safety Valve

J. Air Tank Drain Valves

K. Pump Oil Dipstick/Oil

Fill Plug

L. Belt Tensioning Bolt

M. Pressure Switch

A

3





FIG. 2



MODEL

D55394

WEIGHT

208 lbs. (94.4 kg)

HEIGHT

22.3" (566.4 mm)

WIDTH

24.2" (614.7 mm)

LENGTH

50" (1270 mm)

AIR TANK CAPACITY (GALLONS)

10.5 (39.7 liters)

APPROX CUT-IN PRESSURE

120 psi

APPROX. CUT-OUT PRESSURE

150 psi

SCFM @ 100 PSI

*10.5

NOISE LEVEL

+78 dBA

*Tested per ISO 1217

+Tested per ISO 3744

PUMP CYLINDER

AND HEAD

AFTERCOOLER



The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

e

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

eWALT (1-800-433-9258)



WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

WARNING: This product contains chemicals known to the

State of California to cause cancer, and birth defects or other

reproductive harm. Wash hands after handling.

4



• Restrictinganyofthe

compressor ventilation

openings will cause serious

overheating and could

cause fire.

• Neverplaceobjectsagainst

or on top of compressor.

• Operatecompressorin

an open area at least 12"

(30.5 cm) away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

• Operatecompressorina

clean, dry well ventilated

area. Do not operate unit

indoors or in any confined

area.

• Unattendedoperationof

this product could result in

personalinjuryorproperty

damage. To reduce the

risk of fire, do not allow

the compressor to operate

unattended.

• Alwaysremaininattendance

with the product when it is

operating.

• Alwaysturnoffandunplug

unit when not in use.

WARNING: Some dust contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm

such as asbestos and lead in lead based paint.



DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Itisnormalforelectrical

contacts within the motor

and pressure switch to

spark.

 • Alwaysoperatethecompres-

sor in a well ventilated area

free of combustible materials,

gasoline, or solvent vapors.

 • Ifelectricalsparksfrom

compressor come into con-

tact with flammable vapors,

they may ignite, causing fire

or explosion.

 • Ifsprayingflammablemate-

rials, locate compressor

at least 20' (6.1 m) away

from spray area. An addi-

tional length of hose may be

required.

 • Storeflammablematerialsin

a secure location away from

compressor.

5



DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thecompressedairdirectly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminants can cause

seriousinjuryordeath.

• Neveruseairobtaineddirectly

from the compressor to supply

air for human consumption.

The compressor is not

equipped with suitable filters

and in-line safety equipment

for human consumption.

• Exposuretochemicals

in dust created by

power sanding, sawing,

grinding, drilling, and other

construction activities may

be harmful.

• Sprayedmaterialssuchas

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Workinanareawithgood

cross ventilation. Read and

follow the safety instructions

provided on the label or

safety data sheets for the

materials you are spraying.

Always use certified safety

equipment: NIOSH/OSHA

respiratory protection or

properly fit ting face mask

designed for use with your

specific application.

DANGER: RISK OF INJURY OR PROP ER TY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Oilcanleakorspillandcould

result in fire or breathing

hazard;seriousinjuryor

death can result. Oil leaks will

damage carpet, paint or other

surfaces in vehicles or trailers.

• Alwaysplacecompressor

on a protective mat when

transporting to protect against

damage to vehicle from leaks.

Remove compressor from

vehicle immediately upon arrival

at your destination. Always keep

compressor level and never lie

on its side.

WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed and may

be UM coded (for units with air tanks greater than 6 inch diameter)

according to ASME Section VIII, Div. 1 rules. All pressure vessels

should be inspected once every two years. To find your state pressure

vessels inspector, look under the Division of Labor and Industries in

the government section of a phone book or call 1-800-4-D

eWALT for

assistance.

The following conditions could lead to a weakening of the air tank and

result in a violent air tank explosion:

6



WHAT CAN HAPPEN HOW TO PREVENT IT

• Failuretoproperlydrain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drainairtankdailyorafter

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modificationsorattempted

repairs to the air tank.

• Neverdrillinto,weld,ormake

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorizedmodifications

to the, unloader valve,

safety valve or any other

components which control air

tank pressure.

• Theairtankisdesigned

to withstand specific

operating pressures. Never

makeadjustmentsorparts

substitutions to alter the factory

set operating pressures.

Attachments & accessories:

• Exceedingthepressure

rating of air tools, spray guns,

air operated accessories,

tires and other inflatables can

cause them to explode or

fly apart, and could result in

seriousinjury.

• Followtheequipment

manufacturers

recommendation and never

exceed the maximum

allowable pressure rating

of attachments. Never use

compressor to inflate small

lowpressureobjectssuch

as children’s toys, footballs,

basketballs, etc.

Tires:

• Over inflation of tires could

resultinseriousinjuryand

property damage.

 • Useatirepressuregaugeto

check the tires pressure before

each use and while inflating

tires; see the tire sidewall for

the correct tire pressure.

NOTE: Air tanks, compressors and

similar equipment used to inflate

tires can fill small tires similar to

theseveryrapidly.Adjustpressure

regulator on air supply to no more

than the rating of the tire pressure.

Add air in small increments and

frequently use the tire gauge to

prevent over inflation.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• This air compressor is

powered by electricity.

Like any other electrically

powered device, If it is not

used properly it may cause

electric shock.

 • Never operate the

compressor outdoors when it

is raining or in wet conditions.

 • Never operate compressor

with protective covers

removed or damaged.

7



 • Repairs attempted by

unqualified personnel can

resultinseriousinjuryor

death by electrocution.

 • Any electrical wiring or

repairs required on this

product should be performed

by a D

eWALT factory

service center or a D

eWALT

authorized service center in

accordance with national and

local electrical codes.

 • Electrical Grounding:

Failure to provide adequate

grounding to this product

couldresultinseriousinjury

or death from electrocution.

See Grounding

Instructions under

Installation.

 • Make sure the electrical circuit

to which the compressor is

connected provides proper

electrical grounding, correct

voltage and adequate fuse

protection.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thecompressedairstream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particlesandsmallobjects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Neverpointanynozzleor

sprayer toward any part of

the body or at other people or

animals.

• Alwaysturnthecompressoroff

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touchingexposedmetal

such as the compressor

head, engine head, engine

exhaust or outlet tubes, can

result in serious burns.

 • Nevertouchanyexposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation.

 • Donotreacharound

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

8



WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Movingpartssuchasthe

pulley, flywheel and belt can

causeseriousinjuryifthey

come into contact with you or

your clothing.

• Neveroperatethecompressor

with guards or covers which

are damaged or removed.

• Keepyourhair,clothingand

gloves away from moving

parts.Looseclothes,jewelry

or long hair can be caught in

moving parts.

• Airventsmaycovermoving

parts and should be avoided

as well.

• Attemptingtooperate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in

seriousinjury.

• Anyrepairsrequiredonthis

product should be performed

by a D

eWALT factory

service center or a D

eWALT

authorized service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafeoperationofyourair

compressor could lead to se ri-

ousinjuryordeathtoyouor

others.

• Reviewandunderstandall

instructions and warnings in

this manual.

• Becomefamiliarwiththe

op eration and con trols of the

air compressor.

• Keepoperatingareaclearofall

persons, pets and obstacles.

• Keepchildrenawayfromthe

air compressor at all times.

• Donotoperatetheproduct

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Neverdefeatthesafetyfea

tures of this prod uct.

• Equipareaofoperationwitha

fire extinguisher.

• Donotoperatemachinewith

missing, broken or un au tho-

rized parts.

• Neverstandonthecompressor.

9



WARNING: RISK OF

INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Seriousinjurycanresultfrom

attempting to lift too heavy

anobject.

 • Thecompressoristooheavy

to be lifted by one person.

Obtain assistance from others

before lifting.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Undersomeconditionsand

duration of use, noise from

this product may contribute

to hearing loss.

 • Alwayswearcertifiedsafety

equipment: ANSI S12.6

(S3.19) hearing protection.







DUAL CONTROL

Dual control allows the compressor to operate in the constant

run or the stop/start mode of operation. The unloader valve (H)

is used to control the compressor when operating in the constant

run mode. The pressure switch is used to control the compressor

when operating in the stop/start mode. The mode of operation is

determined by the amount of time the compressor will be required to

supply air. If the demand for air is infrequent, then the unit should be

operated in the stop/start mode to minimize unnecessary run time

and to save energy. If there is a frequent or extended demand for

air, and/or the unit is located in a remote area where access to the

compressor is difficult, the unit should be operated in the constant

run mode to minimize the number of times the motor must start in

an hour to ensure good motor life.

UNLOADER VALVE

When the maximum air tank pressure is

H

obtained, the unloader valve (H) will blow-off.

This will cause the compressor to exhaust the

air to the atmosphere and not the tank. The

valve is preset by the manu facturer and must not

be removed or modified in any way.

PRESSURE SWITCH

The pressure switch (M) automatically starts the motor when the air

tank pressure drops below the factory set cut-in pressure. It stops

the motor when the air tank pressure reaches the factory set cut-out

pressure. The pressure release valve located on the side of the pres-

sure switch, is designed to automatically release compressed air from

the compressor head and the outlet tube when the air compressor

reaches cut-out pressure or is shut off. The pressure release valve

allows the motor to restart freely. When the motor stops running, air will

be heard escaping from this valve for a few seconds. No air should be

heard leaking when the motor is running.

SAFETY VALVE

This valve (I) is designed to prevent system

I

failures by relieving pressure from the system

when the compressed air reaches a predeter-

mined level. The valve is preset by the manu-

facturer and must not be removed or modified in

any way.

10



AIR INTAKE FILTER

The filter (A) is designed to clean air entering the pump.

A

To ensure the pump continually receives a clean, cool

and dry air supply the filter must always be clean and

the filter intake must be free from obstructions.

AIR TANK DRAIN VALVE

The drain valve (J) is used to remove

J

moisture from the air tank after the air

compressor is shut off.

AIR TANK PRESSURE GAUGE

The air tank pressure gauge (D)

200

180

160

140

120

100

80

60

40

20

E

F

D

indicates air pressure in the air tank.

REGULATED PRESSURE GAUGE

The regulated pressure gauge (E)

indicates the air pressure available at

the outlet side of the regulator. This

pressure is controlled by the regulator and is always less or equal to

the air tank pressure.

REGULATOR

The regulator knob (F) controls the air pressure coming from the air

tank.

To Adjust Regulator:

1. Pull regulator knob (F) out.

2. Turn knob clockwise to increase regulated pressure and

counterclockwise to decrease regulated pressure.

3. When desired pressure is shown on the regulated pressure

gauge push knob in to lock.

MOTOR OVERLOAD PROTECTOR

The motor has a thermal overload protector. If the motor overheats

for any reason, the overload protector will shut off the motor. The

motor must be allowed to cool down before restarting. To restart:

1. Set the On/Off switch to OFF and unplug unit.

2. Allow the motor to cool.

3. Depress the red reset button on the motor.

4.

Plug the power cord into the correct branch circuit receptacle.

5. Set the On/Off switch to ON/AUTO position.





INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Apply sealant tape to hose threads.

3. Assemble hose to air outlet (G). IMPORTANT: Do not assemble

splitters directly to the air outlet (G).

NOTE: Assembling quick connect bodies to air outlet (G) and quick

connect plugs to hose ends make connecting and disconnecting

hoses simple and easy. Quick connect bodies and plugs are

available for purchase from your local dealer or authorized service

center.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Remove hose(s) from air outlet(s) (G).

11





AIR COMPRESSOR

The air compressor pump was filled WITH oil at the manufacturer.

Check air compressor pump oil level before operating unit. See

Compressor Pump Oil under Maintenance.



WARNING: Risk of electrical shock. In the event of a short

circuit, grounding reduces the risk of shock by providing an escape

wire for the electric current. This air compressor must be properly

grounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug.

1. The cord set and plug (N) with this unit

P

N

O

contains a grounding pin (O). This plug

MUST be used with a grounded outlet

(P).

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Ensure the outlet being used has the same configuration as the

grounded plug. DO NOT USE AN ADAPTER.

3. Inspect the plug and cord before each use. Do not use if there

are signs of damage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualified electrician.

DANGER: Risk of electrical shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICAL SHOCK.

•

Do not modify the plug provided. If it does not fit the available

outlet, a correct outlet should be installed by a qualified

electrician.

•Repairs to the cord set or plug MUST be made by a qualified

electrician.



Using extension cords is not recommended. The use of extension

cords will cause voltage to drop resulting in power loss to the motor

and overheating.

Instead of using an extension cord, increase the working reach of

the air hose by attaching another length of hose to its end. Attach

additional lengths of hose as needed.

If an extension cord must be used, be sure it is:

 • a3wireextensioncordthathasa3bladegroundingplug,and

a 3-slot receptacle that will accept the plug on the product

 • ingoodcondition

 • nolongerthan50feet(15.2m)

 • 12gauge(AWG)orlarger.(Wiresizeincreasesasgaugenum-

ber decreases. 10 AWG and 8 AWG may also be used. DO NOT

USE 14 OR 16 AWG.)



Refer to Voltage and Minimum Branch Circuit Requirements

under Motor Specifications.

CAUTION: Certain air compressors can be operated on a

20 amp circuit if the following conditions are met.

• VoltagesupplytocircuitmustcomplywiththeNationalElectrical

Code.

• Circuitisnotusedtosupplyanyotherelectricalneeds.

• Extensioncordscomplywithspecifications.

• Circuitisequippedwithasufficientsizecircuitbreakerortime

delay fuse for the motor set up, see Motor Specifications. NOTE:

If compressor is connected to a circuit protected by fuses, use

only time delay fuses. Time delay fuses should be marked "D" in

Canada and "T" in the US.

12



If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a circuit capable of providing a larger

amount of current, see Motor Specifications. It is not necessary to

change the cord set.



Air tools and accessories that are run off the compressor must be

compatible with petroleum based products. If you suspect that a

material is not compatible with petroleum products, an air line filter

for removal of moisture and oil vapor in compressed air is required.

NOTE: Always use an air line filter to remove moisture and oil vapor

when spraying paint.



CAUTION: Risk of personal injury. In order to avoid damaging

the air compressor, do not allow the unit to be tilted more than 10º

when operating.

Place air compressor at least 12" (30.5 cm) away from obstacles that

may prevent proper ventilation. Keep unit away from areas that have

dirt, vapor and volatile fumes in the atmosphere which may clog and

gum up the intake filter and valves, causing inefficient operation.

HUMID AREAS

In frequently humid areas, moisture may form in the pump and

produce sludge in the oil, causing running parts to wear out

prematurely. Excessive moisture is especially likely to occur if the unit

islocatedinanunheatedareathatissubjecttolargetemperature

changes. Two signs of excessive humidity are external condensation

on the pump when it cools down and a "milky" appearance in

compressor oil. You may be able to prevent moisture from forming in

the pump by increasing ventilation or operating for longer intervals.

NOISE CONSIDERATIONS

Consult local officials for information regarding acceptable noise

levels in your area. To reduce excessive noise, use vibration mounts

or silencers, relocate the unit or construct total enclosures or baffle

walls. Contact a D

e

WALT service center or call 1-800-4-D

e

WALT for

assistance.

ELECTRICAL

Refer to all safety instructions before using unit. Observe extension

cord safety instructions if necessary. Always move the On/Off switch

to the OFF position before removing the plug from the outlet.

TRANSPORTING

WARNING: Risk of injury from lifting. Unit weighs more than 160

lbs. (72.6 kg) Do not move or lift without assistance.

CAUTION: Risk of personal injury. The wheels and handle do not

provide adequate clearance, stability or support for pulling the unit

up and down stairs or steps. The unit must be lifted or pushed up

a ramp.

When transporting the com-

Q,R

S

Q,R

Q

pressor in a vehicle, trailer, etc.

ensure that the air tank is

drained and the unit is secured

and placed on a flat horizontal

surface. NOTE: Use

recommended tie down points

(Q) when transporting. Use

care when driving so to avoid tipping the unit over in the vehicle.

Damage can occur to the unit or surrounding items if unit is tipped.

Use a ramp if loading or unloading the unit from a height of more

than 12" (30.5 cm).

13



LIFTING

WARNING: Risk of injury from lifting. Unit weighs more than 160

lbs. (72.6 kg) Do not move or lift without assistance.

Always use two people when lifting and lift from the recommended

lift points (R).

MOVING

1. Grasp handle (S) of compressor and lift compressor high

enough so unit can be rolled on the front tire(s).

WARNING: Risk of unsafe operation. Ensure proper footing and

use caution when rolling compressor so that unit does not tip or

cause loss of balance.

2. When location is reached slowly lower rear of compressor to

ground. Always store compressor in a horizontal position.



The piping, fittings, receiver tank, etc. must be certified safe for at

least the maximum working pressure of the unit. Use hard welded or

threaded steel or copper pipes, cast iron fittings and hoses that are

certified safe for the units discharge pressure and temperature. Use

pipethreadsealantonallthreads,andtightenjointsthoroughlyto

prevent air leaks. DO NOT USE PVC PLASTIC.

WARNING: Riskofbursting.PlasticorPVCpipeisnotdesigned

for use with compressed air. Regardless of its indicated pressure

rating, plastic pipe can burst from air pressure. Use only metal pipe

for air distribution.

CONDENSATE DISCHARGE PIPING

If installing a condensate discharge line, the piping must be at least

one size larger than the connection, as short and direct as possible,

secured tightly and routed to a suitable drain point. Condensate

must be disposed of in accordance with local, state and federal laws

and regulations.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g., tank, filter, aftercoolers, dryers).

This condensate contains oil and/or substances which may be

regulated and must be disposed of in accordance with local, state,

and federal laws and regulations.





1.

Ensure the On/Off switch (C) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

4. Ensure the drain valve (J) is closed.

5. Ensure safety valve (I) is functioning properly, see Checking

Safety Valve under Maintenance.

6. Check pump oil level, see Compressor Pump Oil under

Maintenance.

CAUTION:

Risk of property damage. Do not operate without oil or

with inadequate oil.

D

e

WALT

is not responsible for compressor failure

caused by inadequate oil.

7. Turn regulator knob (F) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 psi.

8. Visually inspect drive belt. Replace belt if frayed, cracked, or worn.

NOTE: Outer belt cover must be removed to inspect drive belt.

9. Visually inspect air hose, replace if needed.

10. Attach hose and accessories.

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

14



WARNING: Risk of Bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressuremustneverexceedthemaximumpressurerating.

11. Ensure all covers and labels are in place, legible (for labels) and

securely mounted. Do not use compressor until all items have

been verified.





WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

BREAK-IN PROCEDURE

WARNING: Serious damage may result if the following break-in

instructions are not closely followed.

This procedure is required before the air compressor is put into

service for the first time and when the check valve or a compressor

pump/motor has been replaced.

1. Ensure the On/Off switch (C) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Open the drain valve (counterclockwise) fully to permit air to

escape and prevent air pressure build up in the air tank during

the break-in period.

4. Move the On/Off switch to the ON position. The compressor will

start.

5. Run the compressor for 20 minutes.

6. After 20 minutes, close the drain valve by turning clockwise s

o

the air tank pressure can build

.

7. Compressed air will be available until it is used or bled off.





1. Follow Pre-Start Checklist under Preparation for Use.

2. Move the On/Off switch to the ON position. The compressor will

start.

3. Allow compressor to pump up to cut-out pressure.

WARNING: Risk of unsafe operation. If any unusual noise

or vibration is noticed, stop the compressor and refer to the

troubleshooting section.

4. Attach hose and accessory.

CAUTION: Risk of unsafe operation. Compressed air from the unit

may contain wa ter condensation and oil mist. Do not spray un fil tered

air at an item that could be damaged by moisture. Some air op er ated

tools or de vic es may require filtered air. Read the in struc tions for the

air tool or device.

 5.Adjust regulator (F) to desired setting. See Regulator under

Features.



WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

WARNING: Risk of moving parts. Keep your hair, clothing, and

gloves away from moving parts. Loose clothes, jewelry or long hair

can be caught in moving parts. Air vents may cover moving parts and

should be avoided as well.

STOP START MODE

1. Ensure the On/Off switch (C) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See Voltage and Circuit Protection under Installation.

15



3. Open the drain valve (counter-clockwise).

4. Move the On/Off switch to the ON position. The compressor will

start.

5. Turn knob on unloader valve (H) clockwise until fully closed.

6. Close drain valve (clockwise).

WARNING: Risk of property damage. Over tightening the Unloader

Valveknobcancausedamagetotheunloadervalve.

7. Allow compressor to reach cut-out pressure. If compressor does

not stop, contact a D

e

WALT service center or call 1-800-4-D

e

WALT

for assistance.

IMPORTANT: Always turn unloader valve knob counter-clockwise until

it stops before moving the On/Off switch (C) to the OFF position.

CONSTANT RUN MODE

1. Ensure the On/Off switch (C) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Open the drain valve (counter-clockwise).

4. Move the On/Off switch to the ON position. The compressor will

start.

NOTE: Compressor must be running when performing the

following operation

5. Turn knob on unloader valve (H) fully counter-clockwise until fully

open.

NOTE: After the compressor reaches cut-out pressure the unit

will continue to run but will not build additional tank pressure until

the air is used and the unloader valve reset pressure is reached.

A slight air noise may be heard while the air is being unloaded

through the pump head.

6. Close drain valve (clockwise).

WARNING: Risk of property damage. Over loosening the unloader

valve knob can cause damage to the unloader valve.

7. The compressor is now in constant run mode. If compressor shuts

off, contact a D

e

WALT service center or call 1-800-4-D

e

WALT for

assistance.

NOTE: For proper operation the unloader valve cut-out pressure must

be below the pressure switch cut out pressure.



IMPORTANT: Always turn unloader valve knob clockwise until it

stops before moving the On/Off switch (C) to the OFF position when

unit is in the constant run mode.

1. Move On/Off switch (C) to the OFF position. NOTE: If finished

using compressor, follow Steps 2 - 6.

2. Turn regulator knob (F) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 psi.

3. Remove hose and accessory.

4. Drain the air tank,

see Draining Air Tank under Maintenance

.

Ensure air tank pressure gauge reads 0 psi.

WARNING: Risk of bursting. Water will condense in air tank. If not

drained, water will corrode and weaken the air tank causing a risk of

air tank rupture.

5. Allow the compressor to cool down.

6. Wipe air compressor clean and store in a safe, non-freezing area.



The following procedures must be followed when maintenance or

service is performed on the air compressor.

1. Ensure On/Off switch is in the OFF position.

2. Remove air compressor plug from outlet.

3. Drain air tank.

4. Allow air compressor to cool down before starting service.

NOTE: All compressed air systems contain maintenance parts (e.g.,

oil, filters, separators) that are periodically replaced. These used parts

16



may contain substances that are regulated and must be disposed of in

accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should be

performed by a D

eWALT factory service center or a DeWALT autho-

rized service center.



Procedure Daily Weekly Monthly 1 year or

200 Hours

Check safety valve

X

Inspect air filter

+

X

Drain air tank***

X

Check pump oil level

X

Change pump oil**

+

X

Oil leak inspection

X

Inspect drive belt

X

Check drive belt tension

X

Check pulley/flywheel

alignment

X

Check for unusual noise/

vibration

X

Check for air leaks*

X

Clean compressor exterior

X

*To checkforair leaksapply a solution ofsoapy water around joints.

While compressor is pumping to pressure and after pressure cuts out,

look for air bubbles to form.

** The pump oil must be changed after the first 20 hours or operation.

Thereafter, when using

DeWALT

synthetic compressor oil, change oil

every 200 hours of operation or once a year, whichever comes first.

*** Drain tanks daily or after four hours of use.

+ Perform more frequent in dusty or humid conditions.



WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

anexplosion.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. If the valve is stuck

or does not operate smoothly, it must be replaced with the same

type of valve.



WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

1. Ensure On/Off switch is in the OFF position.

2. Allow unit to cool.

3. Remove filter (A) top from filter base by turning filter counter-

clockwise about 5 degrees.

4. Separate filter top from base.

5. Remove element from filter base.

6. If element needs cleaning, blow out with air. Replace if needed.

17



Purchase replacement parts from your local dealer or authorized

service center. Always use identical replacement parts.

7. Place element back in filter base.

8. Reconnect filter top to filter base. While pushing in, rotate clock-

wise 5 degrees.

CAUTION: Risk of unsafe operation. Do not operate without air

inlet filter.



WARNING: Risk of unsafe operation. Risk from noise. Air tanks

contain high pressure air. Keep face and other body parts away from

outlet of drain. Use safety glasses [ANSI Z87.1 (CAN/CSA Z94.3)]

when draining as debris can be kicked up into face.

WARNING: Use ear protection [ANSI S12.6 (S3.19)] as air flow

noise is loud when draining.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g., tanks, filter, aftercoolers,

dryers). This condensate contains lubricating oil and/or substances

which may be regulated and must be disposed of in accordance with

local, state and federal laws and regulations.

1. Ensure On/Off switch is in the OFF position.

2. Place a suitable container under the drain valve to catch

discharge.

WARNING: Risk of bursting. Water will condense in the air tank.

If not drained, water will corrode and weaken the air tank causing a

risk of air tank rupture.

CAUTION: Risk of property damage. Drain water from air tank may

contain oil and rust which can cause stains.

3. Grasp black lever on drain valve (J).

4. Slowly rotate lever to gradually bleed air from air tank.

5. When air tank pressure gauge reads 10 psi, rotate valve to the

fully open position.

6. Close drain valves when finished.



CHECKING OIL

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

CAUTION: Risk of unsafe operation. Overfilling with oil will cause

premature compressor failure. Do not overfill.

NOTE: When filling the crankcase, the oil flows very slowly into the

pump. If the oil is added too quickly, it will overflow and appear to

be full.

1. Ensure On/Off switch is in the OFF position.

2. Place unit on a flat level surface.

3 Remove dipstick (K) and wipe clean.

4. Insert and remove dipstick without

MAX.

OIL

MIN.

threading dipstick into crankcase as

shown in figure.

5. Check the oil level on dipstick.

If oil level is at or below "Add",

oil needs to be added. Add D

eWALT

synthetic oil to the proper maximum level as shown in figure.

6. Replace dipstick/oil fill plug and tighten securely.

CHANGING OIL

NOTE: Pump oil contains substances that are regulated and must

be disposed of in accordance with local, state and federal laws and

regulations.

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

1. Ensure On/Off switch is in the OFF position.

18



2. Allow the unit to cool.

3. Remove air compressor plug from outlet.

4. Drain air tank.

5. Locate a suitable container under pump drain plug (J).

6. Remove the dipstick/oil fill plug (K) from crank case.

7. Remove the oil drain plug (B).

8. Allow ample time for all oil to drain out. (Tilting the compressor

towards the drain plug will assist in draining.)

9. Install the oil drain plug.

10. Fill pump with D

eWALT synthetic compressor oil. The oil level

should be at "Add" on the dipstick.

11. Replace dipstick/oil fill plug and tighten securely.



WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

1. Ensure motor ON/OFF switch (C) is in the OFF Position.

2. Allow the unit to cool.

3. Unplug unit.

4. Drain air tank.

5. Remove eight belt guard screws.

6. Remove outer belt cover.

7. Measure belt tension. Proper tension is achieved when a three

(3) pound weight or equivalent finger pressure applied midway

between the motor pulley and compressor flywheel causes a

1/4"(6.35mm)deflectionofthebelt,ifadjustmentisneededsee

Adjusting Belt Tension under Maintenance.

8. Replace belt guard.



WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior

to servicing.

1. Ensure motor ON/OFF switch (C) is in the OFF position.

2. Allow the unit to cool.

3. Unplug unit.

4. Drain air tank

5. Loosen but do not remove four pump

mounting bolts.

6. Remove eight belt cover screws.

7. Remove outer belt cover.

8. Turn belt tensioning (L) bolt

clockwise to increase belt tension or

counterclockwise to loosen belt tension.

9. Check the belt tension again. See Step 8

in Checking Belt Tension under Maintenance.

10. When tension is correct, retighten four

L

pump mounting bolts (torque to

18– 22 ft– lbs/24.4–29.8 Nm), and

replace belt cover.





The air compressor flywheel and motor pulley

must be in-line (in the same plane) within 1/16" (1.6 mm) to ensure

belt retention within flywheel belt grooves. To check alignment:

1. Ensure motor ON/OFF switch (C) is in the OFF Position.

2. Allow the unit to cool.

3. Unplug unit.

19



4. Drain air tank.

5. Remove outer belt cover.

6. Place a straightedge (T)

V

T

U

X

Y

Y Z AA

Z AA

W

against the outside of

the flywheel (U) and the

motor drive pulley (V).

7. Measure the distance

between the edge of

the belt (U) and the

straightedge at points X and Y in Figure. The difference between

mea sure ments should be no more than 1/16" (1.6 mm).

8. If the difference is greater than 1/16" (1.6 mm), loosen the

setscrewholdingthemotordrivepulleytotheshaftandadjust

the pulley’s position on the shaft until the X and Y mea sure ments

are within 1/16" (1.6 mm) of each other.

9. Tighten the motor drive pulley setscrew to 140–180 in–lbs

(15.42–20.34 Nm).

10. Visually inspect the motor drive pulley to verify that it is perpendicular

to the drive motor shaft. Points Z and AA of Figure should appear

to be equal. If they are not, loos en the setscrew of the motor drive

pulley and equal ize Z and AA, using care not to disturb the belt

align ment per formed in Step 8.

11. Retighten the motor drive pulley set screw to 140–180 in–lbs

(15.42–20.34 Nm).

12. Reinstall belt guard.



Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center. If

you need assistance in locating any accessory for your tool, please

contact D

eWALT Industrial Tool Co., 701 East Joppa Road, Baltimore,

MD 21286, call 1-800-4-D

eWALT (1-800-433-9258).

CAUTION: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compressor.



Please have the following information available for all service calls:

Model Number ____________ Serial Number ___________

Date and Place of Purchase ____________________________



To assure product SAFETY and RELIABILITY, repairs, maintenance

andadjustmentshouldbeperformedbyaD

eWALT factory service

center, a D

eWALT authorized service center or other qualified

service personnel. Always use identical replacement parts.



DeWALT heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

e

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

20



FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

e

WALT for a free

replacement.



CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air

delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

Code Certification: Products that bear one or more of the following

marks: UL, CUL, ETL, CETL, have been evaluated by OSHA

certified independent safety laboratories and meet the appli-

cable Underwriters Laboratories Standards for Safety.

California Code: Unit may comply with California Code 462 (l) (2)/

(M) (2). Specification/model label is on the side of the air tank

on units that comply with California Code.

Cut-In Pressure: While the motor is off, air tank pressure drops

when accessory is used. When the tank pressure drops to a

certain low level the motor will restart automatically. The low

pressure at which the motor automatically restarts is called

cut-in pressure.

Cut-Out Pressure: When an air compressor is turned on and

begins to run, air pressure in the air tank begins to build. It

builds to a certain high pressure before the motor automatically

shuts off, protecting your air tank from pressure higher than

its capacity. The high pressure at which the motor shuts off is

called cut-out pressure.

Branch Circuit: The circuit carrying electricity from electrical panel

to outlet.

Duty Cycle: This air compressor pump is capable of running con-

tinuously. However, to prolong the life of your air compressor,

it is recommended that a 50%-75% average duty cycle be

maintained; that is, the air compressor pump should not run

more than 30-45 minutes in any given hour.

La page charge ...

DeWalt D55394 Manuel utilisateur

DeWalt D55394 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents