Extron electronics TLI Pro 101 Manuel utilisateur

Taper
Manuel utilisateur
68-1817-01 Rev. E
04 20
TouchLink Pro Interface Control Systems
TLI Pro 101
User Guide
TouchLink
®
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within the
product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website,
www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer darauf
aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes
gefährliche Spannungen herrschen, die nicht isoliert sind und die einen
elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie
in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y
temas relacionados, consulte la Guía de cumplimiento de normativas
y seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron,
www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire
l’utente della presenza di importanti istruzioni di funzionamento e
manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron,
www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy
pokrewne, zobacz Extron bezpieczeństwa i regulacyjnego zgodności
przewodnik, część numer 68-290-01, na stronie internetowej Extron,
www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению
электрическим током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 简体中文
警告 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压,
险。
注意 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站 , www.extron.com,参见
Extron 安全规范指南,产品编号 68-290-01
Safety Instructions
安全記事 • 繁體中文
警告: 若產品上使用此符號,是為了提醒使用者產品機殼內在著
可能會導致觸電之風險的未絕緣危險電壓
注意 產品上使用此符號,是為提醒使用設備隨附的手冊中有
護( )説
有關安全性指導方針法規遵EMI/EMF 相容存取範圍和主題的詳細
資訊請瀏覽 Extron 網站www.extron.com然後參《Extron 安全性與
法規遵守手冊則編號 68-290-01
安全上の注意
日本語
警告: この が製品上に表示されている場合は、筐体内に絶縁され
いない高電圧が流れ、感電の危険があるこていま
意:この 品上に表されている場合は、の取扱説書に
されている重作と保()についてユザー
を喚起するものです
安全上の注意、法規厳守、EMI/EMF適合性、その他の関連項
スト イト www.extron.com よ り Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01)ご覧ださい。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한
자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수
안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause interference.
This interference must be corrected at the expense of the user.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and Regulatory
Compliance Guide on the Extron website.
Battery Notice
This product contains a battery. Do not open the unit to replace the battery. If the
battery needs replacing, return the entire unit to Extron (for the correct address, see the Extron
Warranty section on the last page of this guide).
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions.
ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.
Débarrassez-vous des piles utilisées selon le mode d’emploi.
Copyright
© 2014 - 2020 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks®, registered service marks(SM), and trademarks(TM) are the property of RGBSystems, Inc. or
Extron Electronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Glitch Free, Global Configurator,
Global Scripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,
PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,
System INTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP Systems, and
ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D
Ripple Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator,
DSPConfigurator, DSVP (Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk,
MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, SIS,
Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy
Conventions Used in this Guide
In this user guide, the following are used:
Notifications
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
Risk of property damage.
Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Commands are written in the fonts shown here:
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” represents the
capital letter “o”.
Computer responses and directory paths that do not have variables are written in the font
shown here:
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at www.extron.com/technology/glossary.aspx.
Contents
Introduction ....................................................1
About the TLI Pro 101 ..........................................1
Features ............................................................... 1
Application Diagram .............................................2
Requirements ....................................................... 2
Software ..........................................................2
Hardware .........................................................2
Installation Overview .....................................3
Panel Features, Connections, and Setup .... 5
TLI Pro 101 Rear Panel Features
and Connections .................................................5
TLI Pro 101 Front Panel Features .......................12
On-screen Menus ........................................13
Setup Menu .......................................................13
Status ............................................................13
Network .........................................................14
Output ...........................................................16
Audio .............................................................18
Input ..............................................................19
Advanced ......................................................21
Calibration Screen .............................................. 22
Configuration Software ...............................23
Configuration Software ....................................... 23
Downloading software from
the product page ..........................................24
Downloading software from
the alphabet menu ........................................25
Using the Software ............................................. 25
Toolbelt ..........................................................25
GUI Designer .................................................25
Global Configurator Plus and Professional ...... 25
Global Scripter ...............................................25
TLI Pro 101 Web Page .......................................26
Updating the Firmware .......................................27
Downloading Firmware Using
Extron Firmware Loader ................................27
Mounting ......................................................29
Tabletop Placement............................................29
Rack Mounting ...................................................29
Underwriters Laboratories Guidelines
for Rack Mounting ........................................29
Rack Mounting the TLI Pro 101 ...................... 29
Under-desk Mounting.........................................29
Reference Material ......................................30
Network Port Requirements and Licensed
Third-party Software Used by
the Touchpanels ................................................ 30
Reset Modes......................................................30
Use Factory Firmware ....................................30
Reset All IP Settings ....................................... 31
Reset to Factory Defaults ...............................31
Enable or Disable the DHCP Client .................32
Secure Sockets Layer (SSL) Certificates ............. 32
IEEE 802.1X Certificates .....................................33
Certificate File Requirements ..........................33
Private Key File Requirements ........................33
TLIPro101 • Contents vi
TLIPro101 • Contents vii
Introduction
This guide describes the function, installation, and operation of the TLIPro101. Unless
otherwise stated, the terms “interface” and “TouchLink Pro interface” refer to the TLIPro101.
This section provides an overview of the TLI Pro 101:
About the TLI Pro 101
Features
Application Diagram
Requirements
About the TLI Pro 101
The Extron TLIPro101 is a TouchLink Interface that works with any Extron IP Link Pro control
processor to allow a third-party touchscreen display to be used as a point of control within
an Extron Pro Series control system. The scaled output supports displays with resolutions up
to 2K.
Events such as button presses on the touchpanel trigger signals to the TLIPro101. These
signals are converted to a form that can be understood by an IP Link Pro Control Processor.
When the control processor sends return signals, the TLIPro101 outputs a video signal to
the touchpanel showing the status of feedback events. When the third-party touchpanel and
TLIPro101 have been set up correctly, they have control system capabilities similar to other
Extron TLPPro products.
Features
Compatible with third-party touchscreen displays — integrates third-party touchscreen
displays up to 2K or touchpanels with ultra-low radiation emission into Extron systems.
Fast processing and ample memory — allows for quicker configuration uploads and more
storage for GUI pages.
Compatible with all IP Link Pro control processors — providing control for a wide range
of systems.
Compliant with the requirements of Power over Ethernet (PoE) 802.3af, class 3
receives power and control over a single Ethernet cable, eliminating the need for a local power
supply (the power injector is sold separately).
Supports HDCP-compliant HDMI — for full-motion video preview and monitoring.
Advanced Extron video signal processing — with a high performance scaling engine.
One USB 2.0 port — for third-party touchscreens or HID support. Increases device
functionality.
Automatic clock synchronization — for accurate time and date display.
Adjustable sleep timer — puts interface into sleep mode.
Fully customizable using Extron control system software — GUI Designer combined
with Global Configurator Plus and Global Configurator Professional.
Supports TouchLink for iPad and TouchLink for Web
Energy-efficient external universal power supply included — provides worldwide
compatibility, low power consumption, and reduced operating costs.
TLIPro101 • Introduction 1
Application Diagram
POWER
12V
x.xA MAX
G
Tx Rx RTSCTS
COM 1
G
Tx Rx
G
Tx Rx
COM 2
COM 3
1
SG
SG
2
IR/SERIAL
RELAYS
1 2 C
3 4 C
1 2 3 4 G
DIGITAL I/O
PWR OUT = 6W
eBUS
+V +S
-S
G
LAN
123
IPCP PRO 350
LAN
ACT
LINK
RESET
INPUTS
OUTPUTS
12
3
4
56
7
8
US
LISTED
1T23
I.T.E.
®
12
34
56
7
8
TLI PRO 101
LAN/PoE
USB
HDMIHDMI
+
-
POWER
12 V
RESET
CONTROLOUTPUT
1.0A MAX
INPUT
Extron
TLI Pro 101
TouchLink
Interface
STANDBY/ON
PQLS HDMI OPEN/CLOSE FL OFF
USB
WiFi
1234
!
1
@
2
#
3
$
4
%
5
^
6
&
7
*
8
(
9
)
0
_
-
+
=
|
\
}
]
{
[
~
`
QWERTYUIOP
:
;
<
,
>
.
?
/
ASDFGHJ
ZXCVBNM
KL
control
shift
caps lock
tab
esc
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10F11 F12F13 F14F15 F16F17 F18F19
alt
option command
delete
fn home clear
enter
=/
*
8
-
5
2
7
0.
4
1
+
9
6
3
page
up
page
down
enddelete
command option control
shift
return
caps lock
TCP/IP
Network
Ethernet
Ethernet
3rd Party
Touch
Screen
Ethernet
USB
HDMIHDMI
RS-232
RS-232
HDMI
HDMIHDMI HDMI HDMI HDMI
HDMI
HDMI
HDMI
HDMI
Monitor 1
Monitor 2
Monitor
3
Extron
DXP 88 HDMI
HDMI Matrix Switcher
Extron
IPCP Pro 350
IP Link Pro Control
Processor
Blu-ra
y Player
PC
Laptop
Document Camera
Video Camera
Figure 1. TLIPro101 Application Diagram
Requirements
Software
For a complete list of the requirements for running GUI Designer, Global Configurator Plus
and Professional, Global Scripter, or Toolbelt, see the Extron Web page for the appropriate
software.
NOTE: The TLI Pro 101 is not compatible with GlobalConfigurator 3 or GUIConfigurator.
Hardware
An Extron IP Link Pro control processor must be connected to the same network domain as
the TLI Pro 101. See www.extron.com for a list of suitable controllers.
NOTE: The TLI Pro 101 is not compatible with Extron IP Link (non-Pro) control
processors.
TLIPro101 • Introduction 2
Installation
Overview
1. Before starting, download and install the latest versions of the following software:
GUI Designer — for designing layouts for Extron TouchLink Pro touchpanels and
third party touch interfaces.
Global Configurator Plus and Professional — for setting up and configuring the
control processor and touchpanel.
Toolbelt — provides device discovery, device information, firmware updates,
and configuration of network settings, system utilities, and user management for
TouchLink Pro devices.
Global Scripter — Provides an integrated development environment for Extron
control systems programming.
See Configuration Software on page 23.
2. Obtain the following network information from your network administrator:
DHCP setting (On or Off). If the DHCP setting is Off, you also need:
TLI Pro 101 IP address
Subnet mask
Gateway IP address
User name — by default these are either admin or user.
Passwords — the factory configured passwords for all accounts on this device
have been set to the device serial number. Passwords can be changed during
configuration. They are case sensitive.
NOTE: If the device is reset to default settings, the passwords are reset to the
default password, which is extron (for either admin or user).
MAC address — make a note of the TLI Pro 101 MAC address.
3. Mount the units. Stand the TLI Pro 101 on a convenient surface, mount it in a standard
rack, or use an under-table mounting kit (see Mounting on page 29). To mount the
third-party touchpanel follow the instructions provided by the manufacturer.
4. Connect cables to the TLI Pro 101 (see TLI Pro 101 Rear Panel Features and
Connections on page 5).
Connect the HDMI output from the TLI Pro 101 (figure 2,
C
on page 5) to the
third-party touchpanel.
Connect the USB port from the TLI Pro 101 (
D
) to the third-party touchpanel.
NOTE: The USB connection passes information to the TLI Pro 101 about where on
the screen the touchpanel was pressed. To use a normal monitor instead of a
touchscreen, connect a mouse to the TLI Pro 101 USB connection. Use the mouse
to click on screen icons.
TLIPro101 • Installation Overview 3
5. Connect the power cords and power on all devices (see Power on page 6 or
Network and Power over Ethernet (PoE) Connector on page 10).
ATTENTION:
Do not power on the interfaces or control processors until you have read the
Attention on page 7 (12 VDC power supply) or on page 11 (power injector).
Ne branchez pas les interfaces ou les contrôleurs avant d’avoir lu les mises
en garde
page 7 (source d’alimentation 12VCC) ou page 11 (injecteur
PoE).
6. Set up the interface for Network Communication:
Connect the PC that you will use for setup, the control processor, and the TLI Pro 101
to the same Ethernet subnetwork.
Use the Setup Menu (see page 13) or Toolbelt (see the Toolbelt Help File) to
set the DHCP status and, if necessary, the IP address, subnet mask, gateway, and
related settings for the interface.
7. Configure the Interface — the Global Configurator Professional and Global Configurator
Plus Help File and the GUI Designer Help File provide step-by-step instructions and
detailed information.
The Global Configurator Professional and Global Configurator Plus Help File
includes an introduction to the software and sections on how to start a project and
configuration.
Global Scripter provides an Extron-exclusive Python library (ControlScript) and
Global Scripter modules to get you started. See the GlobalScripter Help File for more
information.
TLIPro101 • Installation Overview 4
Panel Features,
Connections, and
Setup
This section describes:
TLI Pro 101 Rear Panel Features and Connections
TLI Pro 101 Front Panel Features
TLI Pro 101 Rear Panel Features and Connections
TLI PRO 101
LAN/PoE
USB
HDMIHDMI
+
-
POWER
12 V
RESET
CONTROLOUTPUT
1.0A MAX
INPUT
AB GFECD
Figure 2. TLIPro101 Rear Panel
A
Power (see page 6)
B
HDMI Input (see page 8)
C
HDMI Output (see page 8)
D
USB Connector (see page 9)
E
Network and Power over Ethernet (PoE) Connector (see page 10)
F
Reset mode LED (see page 12)
G
Reset button (see page 12)
figure 2
TLIPro101 • Panel Features 5
A
Power (see figure 2,
A
, on page 5)— Connect the 2-pole, 3.5 mm captive screw
connector from the provided 12VDC power supply to the power supply socket on the rear
panel. Figure 3 shows how to wire the connector. Ensure the connections have the correct
polarity.
Power Supply
Output Cord
Captive Screw
Connector
SECTION A–A
Ridges
Smooth
AA
Tie Wrap
3/16”
(5 mm) Max.
-
-
Figure 3. Wiring the Power Connector
WARNING: The two DC output cables must be kept separate from each other
while the power supply is plugged in. Remove power before wiring.
AVERTISSEMENT : Les deux câbles de sortie CC doivent être séparés les
uns des autres tant que la source d’alimentation est branchée. Coupez
l’alimentation avant d’effectuer les raccordements.
CAUTION: Risk of Explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the Instructions.
ATTENTION
: Risque d’explosion. Ne pas remplacer la pile par le mauvais type de
pile. Débarrassez-vous des piles utilisées selon le mode d’emploi.
ATTENTION:
Do not power on the interfaces or control processors until you have read the
Attention on page 7 (12 VDC power supply) or on page 11 (power injector).
Ne branchez pas les interfaces ou les contrôleurs avant d’avoir lu les mises
en garde
page 7 (source d’alimentation 12VCC) ou page 11 (injecteur
PoE).
NOTES:
The TLI Pro 101 ships with a 12 VDC, 1.5 A power supply and is also Power over
Ethernet (PoE 802.3af, class3) compliant. The power injector must be purchased
separately.
If a 12 VDC power supply and a PoE power injector are both connected to
the TLIPro101, the power injector takes precedence. If a PoE power loss
is detected, the interface switches seamlessly to the 12 VDC supply without
needing a system reboot.
Power
TLIPro101 • Panel Features 6
ATTENTION:
Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.
This product is intended for use with a UL Listed power source marked “Class 2” or
“LPS” and rated 12VDC, minimum 1.0 A. or 48 VDC (PoE), minimum 0.35 A.
Ce produit est destiné à une utilisation avec une source d’alimentation listéeUL avec
l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum ou 48Vcc
(PoE), 0,35A minimum.
Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
Les sources d’alimentation Extron sont qualifiées UL/CSA60950-1 et sont
classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation non-
listée ou non-listéeLPS annulera toute certification de conformité réglementaire.
Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré2 de pollution, fixé à un équipement de rack
à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code
part 1, section 16.
Cette installation doit toujours être en accord avec les mesures qui s’applique au
National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical Code,
partie1, section16.
The power supply shall not be permanently fixed to the building structure or similar
structure.
La source d’alimentation ne devra pas être fixée de façon permanente à une structure
de bâtiment ou à une structure similaire.
The length of the exposed wires in the stripping process is critical. The ideal length is
3/16 inches (5 mm). If they are longer, the exposed wires may touch, causing a short
circuit between them. If they are shorter, the wires can be easily pulled out even if
tightly fastened by the captive screws.
La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus longs,
les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils sont un
peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.
Do not tin the wire leads before installing into the connector. Tinned wires are not
as secure in the connector and could be pulled out.
Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles
étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être retirés.
Attention
mises en garde
TLIPro101 • Panel Features 7
B
HDMI Input (see figure 2 on page 5) — Plug the cable from the input source device
into this female HDMI type A connector. Secure the HDMI connector to the TLI Pro 101
with the provided LockIt HDMI lacing bracket (see “LockIt HDMI Lacing
Bracket Installation”, below).
The wiring of the connector follows the HDMI single link format.
The diagram to the right and the table below show the HDMI pin
configuration.
Pin Signal Pin Signal Pin Signal
1 TMDS data 2+ 7 TMDS data 0+ 13 CE control
2 TMDS data 2 shield 8 TMDS data 0 shield 14 Reserved (NC)
3 TMDS data 2- 9 TMDS data 0- 15 SCL
4 TMDS data 1+ 10 TMDS clock+ 16 SDA
5 TMDS data 1 shield 11 TMDS clock shield 17 DDC/CEC ground
6 TMDS data 1- 12 TMDS clock- 18 +5 V power
19 Hot plug detect
C
HDMI Output — Connect this female HDMI type A connector to a third-party touch
screen.
A full list of supported Screen Resolutions for video output is shown on the
following page.
LockIt HDMI Lacing Bracket Installation:
Secure the HDMI connector to the TLI Pro 101 with the provided LockIt HDMI lacing
bracket by following these instructions:
HDMI
Type A Receptacle
1
18 2
19
HDMI Input
HDMI Output
1. Plug the source HDMI cable into this
input port.
2. Loosen the HDMI connection mounting
screw from the TLI Pro 101 rear panel
enough to allow the LockIt lacing bracket
to be placed over it. The screw does not
have to be removed.
3. Place the LockIt lacing bracket on the
screw and against the HDMI connector,
then tighten the screw to secure the
bracket.
ATTENTION:
Do not overtighten the HDMI
connection mounting screw.
The shield it fastens to is very
thin and can easily be stripped.
Ne serrez pas trop la vis de
montage du connecteur HDMI.
Le blindage auquel elle est
attachée est très fin et peut
facilement être dénudé.
4.
Loosely place the included tie wrap
around the HDMI connector and the
LockIt lacing bracket as shown.
5. While holding the connector securely
against the lacing bracket, tighten the tie
wrap, then remove any excess length.
3
1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
Figure 4. Securing the HDMI
Connector
TLIPro101 • Panel Features 8
Screen Resolutions
Resolution 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz
800x600 X
1024x768 X
1280x768 X
1280x800 X
1280x1024 X
1360x768 X
1366x768 X
1440x900 X
1400x1050 X
1600x900 X
1680x1050 X
1600x1200 X
1920x1200 X
720p X X X X X X
1080p X X X X X X X X
2048x1080 X X X X X X X X
Custom 1 For new resolutions (eld support only)
D
USB Connector (see figure 2 on page 5) — Supports High-speed USB 2.0 control.
Plug a USB cable from the third-party touchpanel into this female typeB connector.
The USB connection passes information to the TLI Pro 101 about where on
the screen the touchpanel was pressed. To use a normal monitor instead of a
touchscreen, connect a mouse to the TLI Pro 101 USB connection. Use the mouse
to click screen icons.
USB Connector
TLIPro101 • Panel Features 9
E
Network and Power over Ethernet Connector (see figure 2 on page 5) —
Connect the interface to the LAN using a twisted pair cable, terminated with an RJ-45
connector. Use a straight-through Ethernet cable to connect the panel to a switch or
router. Use a crossover cable to connect the panel directly to a computer.
An Extron IPL Pro Control Processor must also be connected to the same network
domain as the interface. See the www.extron.com for a list of suggested models.
The network port has two LEDs. The green LED lights
steadily to indicate that the interface is connected correctly
to a network. The amber LED blinks to indicate that data is
being passed to or from the interface.
Although a 12 VDC, 1.5 A power supply is provided, the
TLIPro 101 is compliant with the requirements of PoE 8.203af, class 3, which means
the unit can be powered by Power over Ethernet. To use Power over Ethernet,
connect this port to a PoE power injector (not provided).
ATTENTION:
The TLI Pro 101 can use a 12 VDC desktop power supply and is also Power over
Ethernet (PoE 802.3af, class3) compliant. Do not connect either power supply
before reading the Attention on page 7 or page 11.
Le TLI Pro 101 peut utiliser une source d’alimentation externe 12 Vcc, et est
également compatible avec l’alimentation POE via Ethernet (PoE802.3af,
classe 3). Ne branchez pas de sources d’alimentation externes avant d’avoir
lu les mises en garde dans la section «PowerSupply» sur page 7 ou
page 11.
Use a straight-through Ethernet cable to connect the power injector to a switch or
router. This cable carries network information from the switch or router to the power
supply input. A second straight-through cable carries the network information and
power from the power supply to the TLIPro101. Connect the IEC power cord to a
convenient 100 VAC to 240 VAC, 50-60 Hz power source.
The figure below shows the Extron XTP PI 100. Your power injector may look
different.
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switchTo TLI Pro 101
Figure 5. Connecting the Power Injector
CAUTION: Risk of Explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
ATTENTION
: Risque d’explosion. Ne pas remplacer la pile par le mauvais type de
pile. Débarrassez-vous des piles utilisées selon le mode d’emploi.
Network and Power over Ethernet (PoE) Connector
LAN
Activity LED
Link LED
RJ-45 Port
TLIPro101 • Panel Features 10
ATTENTION:
The TLI Pro 101 is intended for connection to a Power over Ethernet circuit for intra-
building use only and is considered to be part of a Network Environment 0 per IEC
TR62101.
Le TLI Pro 101 est conçu pour une connexion à un circuit PoE pour une utilisation
intérieure seulement et est considéré comme faisant partie d’un environnement
réseau 0 par IECTR62101.
Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.
This product is intended for use with a UL Listed power source marked “Class 2” or
“LPS” and rated 12VDC, minimum 1.0 A. or 48 VDC (PoE), minimum 0.35 A.
Ce produit est destiné à une utilisation avec une source d’alimentation listéeUL avec
l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum ou 48Vcc
(PoE), 0,35A minimum.
Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
Les sources d’alimentation Extron sont qualifiées UL/CSA60950-1 et sont
classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation non-
listée ou non-listéeLPS annulera toute certification de conformité réglementaire.
Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré2 de pollution, fixé à un équipement de rack
à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
Power over Ethernet (PoE) is intended for indoor use only. It is to be connected only
to networks or circuits that are not routed to the outside plant or building.
L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur uniquement.
Elle doit être connectée seulement à des réseaux ou des circuits qui ne sont pas
routés au réseau ou au bâtiment extérieur.
The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code
part 1, section 16.
Cette installation doit toujours être en accord avec les mesures qui s’applique au
National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical Code,
partie1, section16.
The power supply shall not be permanently fixed to the building structure or similar
structure.
La source d’alimentation ne devra pas être fixée de façon permanente à une structure
de bâtiment ou à une structure similaire.
page 11
TLIPro101 • Panel Features 11
F
Reset mode LED (see figure 2 on page 5) — Provides feedback about the reset
status when the reset button is pressed (see Reset Modes on page 30).
G
Reset button (recessed) — Allows the unit to be reset in any of three different modes
(see Reset Modes).
TLI Pro 101 Front Panel Features
TLI PRO 101
TOUCHLINK INTERFACE
ACT
LINK
100
MENU
AB
ED
C
Figure 6. TLI Pro 101 Plus Front Panel
A
Power LED — Lights when the unit is powered on.
B
Menu button (recessed) — Opens the Setup Menu (see the following page) and
Calibration Screen (see page 22) for the interface:
Setup Menu
1. Press the button briefly (less than 2 seconds) to open the setup menu screens.
2. Press the button briefly for a second time to exit the setup menu.
Calibration Screen
1. Press and hold the button (at least 3 seconds) to open the calibration screen. Follow
the on-screen instructions to calibrate the touchpanel.
2. Complete the calibration process or press the button briefly (less than 2 seconds) for
a second time to exit the Calibration screen.
C
100 Mb network LED — Lights when the unit is connected to a 100 Mb network.
D
Network link LED — Lights when the unit is connected to a network.
E
Network activity LED — Flashes when there is activity on the network connection.
Reset mode LED
Reset button
Power LED
Menu button
100 Mb network LED
Network link LED
Network activity LED
figure 6
TLIPro101 • Panel Features 12
On-screen Menus
On-screen menus allow initial configuration of the TLI Pro 101.
Setup Menu
Calibration Screen
Setup Menu
To access the setup menus, press the recessed front-panel Menu button (see figure 6,
B
, on
page 12).
The menu opens at the Status screen. There are six different screens (Status, Network,
Output, Audio, Input, and Advanced) that can be selected by pressing the appropriate
button in the navigation panel at the top of the screen.
There is also a red
Exit button in the top right corner of the screen. Pressing this button
applies and saves any changes and closes the menu screens.
Status
Info
Model: TLI Pro 101
Part Number: 60-1083-01
Firmware
Version:
1.00
PoE Status: On
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLI-AB-CD-EF
Output
Resolution:
Project:
Sleep Timer:
800x600
N/A
5 Minutes
Audio
Master Volume:
Master Mute: Off
99
Input
HDMI Port: No Signal
Status
Output
Audio
Advanced
Exit
Network
Input
Advanced
Controller IP: N/A
Project Size: N/A
Figure 7. Status Screen
This is a read-only screen. The Info panel provides basic information about the TLIPro101.
Each of the other five panels shows a summary of the information on the other screens.
Pressing any of the panels opens the corresponding screen in exactly the same way as
pressing the buttons in the top navigation panel.
The bubble in the
Network panel lights green when there is a network connection or amber
if there is no connection. The bubble in the
Advanced panel lights green when a control
processor is connected or amber if none is connected.
TLIPro101 • On-screen Menus 13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41

Extron electronics TLI Pro 101 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues