Worx WG751.2 Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire

Ce manuel convient également à

P02
P18
P31
WG751 WG751.9
3-in-1 Cordless Lawn Mower EN
Tondeuse à Gazon Sans Fil 3 en 1 F
Cortacesped de Bateria 3 en 1 ES
2
3-in-1 Cordless Lawn Mower EN
SAFETY INSTRUCTIONS
WARNING: Some dust created by power
sanding, sawing, grinding, drilling and
other construction activities contains
chemicals known to the state of California to
cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
Lead from lead-based paints;
Crystalline silica from bricks and cement
and other masonry products and
Arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemical: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed
to filter out microscopic particles.
WARNING: This product can expose you
to chemicals including lead, phthalate or
bisphenol A which are known to the State of
California to cause cancer, birth defects or
other reproductive harm. Wash your hands
after use. For more information go to www.
P65Warnings.ca.gov.
READ ALL INSTRUCTIONS
WARNING: When using electric lawn mowers,
basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and
personal injury, including the following:
WARNING: Risk of injury could occur if the
lawn mower is operated without the catcher
assembly attached.
WARNING: The use of any other accessory or
attachment might increase the risk of injury
CAUTION: For battery-operated lawn mowers,
use only identical replacement batteries and
specifying the battery type and manufacturer.
FOR ALL LAWN MOWERS
1) Avoid Dangerous Environment - Don’t use lawn
mowers in damp or wet locations.
2) Don’t Use In Rain.
3) Keep Children Away - All visitors should be kept
a safe distance from work area.
4) Dress Properly - Do not wear loose clothing
or jewelry. They can be caught in moving
parts. Use of rubber gloves and footwear is
recommended when working outdoors.
5) Use Safety Glasses - Always use face or dust
mask if operation is dusty.
6) Use Right Appliance - Do not use lawn mower
for any job except that for which it is intended.
7) Don’t Force Lawn Mower - It will do the job
better and safer at the rate for which it was
designed.
8) Don’t Overreach - Keep proper footing and
balance at all times.
9) Stay Alert - Watch what you are doing. Use
common sense. Do not operate lawn mower
when you are tired.
10) Store Idle Lawn Mower Indoors - When not
in use, lawn mower should be stored in an
indoor dry and locked-up place - out of reach
of children.
11) Maintain Lawn Mower With Care - Keep
cutting edges sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories. Keep
handles dry, clean, and free from oil and
grease.
12) Keep guards in place and in working order.
13) Keep blades sharp.
14) Keep hands and feet away from cutting area.
15) Objects struck by the lawn mower blade can
cause severe injuries to persons. The lawn
should always be carefully examined and
cleared of all objects prior to each mowing.
16) If lawn mower strikes a foreign object, follow
these steps:
i) Stop lawn mower. Release the switch.
ii) Remove battery pack.
iii) Inspect for damage.
iv) Repair any damage before restarting and
operating the lawn mower.
17) Use identical replacement blades only.
FOR ALL BATTERY – OPERATED GARDENING
APPLIANCES
1. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to battery pack, picking up or carrying the
appliance. Carrying the appliance with your
finger on the switch or energizing appliance
that have the switch on invites accidents.
2. Disconnect the battery pack from the appliance
before making any adjustments, changing
accessories, or storing appliance. Such
preventive safety measures reduce the risk of
starting the appliance accidentally.
3. Recharge only with the charger specified by the
manufacturer .A charger that is suitable for one
type of battery pack may create a risk of fire
when used with another battery pack.
4. Use appliances only with specifically designated
battery packs. Use of any other battery packs
may create a risk of injury and fire.
5. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
6. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
7. Do not use a battery pack or appliance that is
3
3-in-1 Cordless Lawn Mower EN
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behavior
resulting in fire, explosion or risk of injury.
8. Do not expose a battery pack or appliance to
fire or excessive temperature. Exposure to fire
or temperature above 130°C( 265°F) may cause
explosion.
9. Follow all charging instructions and do not
charge the battery pack or appliance outside
of the temperature range specified in the
instructions. Charging improperly or at
temperatures outside of the specified range may
damage the battery and increase the risk of fire.
10. Have servicing performed by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the product is
maintained.
11. Do not modify or attempt to repair the appliance
or the battery pack (as applicable) except as
indicated in the instructions for use and care.
GENERAL SAFETY
WARNINGS FOR BATTERY
PACK
a) Do not dismantle, open or shred battery
pack.
b) Do not expose battery pack to heat or
fire. Avoid storage in direct sunlight.
c) Do not short-circuit a battery pack. Do not
store battery packs haphazardly in a box
or drawer where they may short-circuit
each other or be short-circuited by other
metal objects.
When battery pack is not in
use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other
small metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or
fire.
d) Do not remove battery pack from its
original packaging until required for use.
e) Do not subject battery pack to mechanical
shock.
f) In the event of battery leaking, do not
allow the liquid to come in contact
with the skin or eyes. If contact has
been made, wash the affected area with
copious amounts of water and seek
medical advice.
g) Observe the plus (+) and minus (–) marks
on the battery back and equipment and
ensure correct use.
h) Do not use any battery pack which is not
designed for use with the equipment.
i) Keep battery pack out of the reach of
children.
j) Seek medical advice immediately if a cell
or battery has been swallowed.
k) Always purchase the battery pack
recommended by the device manufacturer
for the equipment.
l) Keep battery pack clean and dry.
m) Wipe the battery pack terminals with a
clean dry cloth if they become dirty.
n) Battery pack needs to be charged before
use. Always use the correct charger and
refer to the manufacturer’s instructions
or equipment manual for proper charging
instructions.
o) Do not leave battery pack on prolonged
charge when not in use.
p) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
q) Battery pack gives its best performance
when it is operated at normal room
temperature (20 °C ± 5 °C).
r) When disposing of battery packs, keep
battery packs of different electrochemical
systems separate from each other.
s) Recharge only with the charger specified
by WORX Do not use any charger other
than that specifically provided for use
with the equipment.
A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
t) Retain the original product literature for
future reference.
u) Use only the battery pack in the
application for which it was intended.
v) Remove the battery pack from the
equipment when not in use.
w) Dispose of properly.
Safety instructions for walk-behind mowers
IMPORTANT
Safe Practices for Walk-Behind Mowers
I. GENERAL OPERATION
1. Read, understand, and follow all instructions
on the machine and in the manual(s) before
starting.
2. Do not put hands or feet near or under the
machine. Keep clear of the discharge opening
at all times.
3. Only allow responsible adults, who are familiar
with the instructions, to operate this machine.
4. Clear the area of objects such as rocks, wire,
toys, etc., which could be thrown by the blade.
Stay behind the handle when the motor is
running.
5. Be sure the area is clear of bystanders before
operating. Stop machine if anyone enters the
area.
6. Do not operate machine barefooted or while
wearing sandals. Always wear substantial
footwear.
7. Do not pull machine backward unless
absolutely necessary. Always look down and
behind before and while moving backward.
8. Never direct discharged material toward
anyone. Avoid discharging material against
a wall or obstruction. Material may ricochet
back toward the operator. Stop the blade when
4
3-in-1 Cordless Lawn Mower EN
crossing gravel surfaces.
9. Do not operate machine without the entire
grass catcher, discharge guard, rear guard, or
other safety protective devices in place and
working.
10. Never leave a running machine unattended.
11. Stop the motor and wait until the blade comes
to a complete stop before cleaning the machine,
removing grass catcher, or unclogging the
discharge guard.
12. Operate machine only in daylight or good
artificial light.
13. Do not operate machine while under the
influence of alcohol or drugs.
14. Never operate mower in wet grass. Always be
sure of your footing; walk; never run.
15. Disengage the drive system, if so equipped,
before starting the motor.
16. If the machine should start to vibrate
abnormally, stop the motor and check for the
cause immediately. Vibration is generally a
warning of trouble.
17. Always wear eye protection when operating
machine.
18. See manufacturer’s instructions for proper
operation and installation of accessories. Only
use accessories approved by the manufacturer.
II. SLOPE OPERATION
Slopes are a major factor related to slip and
fall accidents, which can result in severe injury.
Operation on all slopes requires extra caution. If you
feel uneasy on a slope, do not mow it.
1. Mow across the face of slopes; never up and
down. Exercise extreme caution when changing
direction on slopes.
2. Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could cause
a slip and fall accident. Tall grass can hide
obstacles.
3. Do not mow on wet grass or excessively steep
slopes. Poor footing could cause a slip and fall
accident.
4. Do not mow near drop-offs, ditches, or
embankments. You could lose your footing or
balance.
III. CHILDREN
Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you
last saw them.
1. Keep children out of the mowing area and
under the watchful care of a responsible adult
other than the operator.
2. Be alert and turn mower off if a child enters the
area.
3. Never allow children to operate the machine.
4. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may block
your view of a child.
IV. SERVICE
GENERAL SERVICE
1. Keep all nuts and bolts tight to be sure the
equipment is in safe working condition.
2. Never tamper with safety devices. Check their
proper operation regularly.
3. Keep machine free of grass, leaves, or other
debris build-up.
4. If you strike a foreign object, stop and inspect
the machine. Repair, if necessary, before
starting.
5. Never make any adjustments or repairs with
the motor running.
6. Always unplug electric mowers before
adjusting, cleaning, or repairing.
7. Check grass catcher components and the
discharge guard frequently and replace with
manufacturers recommended parts, when
necessary.
8. Mower blades are sharp. Wrap the blade or
wear gloves, and use extra caution when
servicing them.
9. Maintain or replace safety and instruction
labels, as necessary.
Safe operation practices for walk-behind
mowers
1. Safety Instructions
1.1 Training
a) Read the operating and service instruction
manual carefully. Be thoroughly familiar
with the controls and the proper use of the
equipment.
b) Never allow children to operate a power
mower.
c) Keep the area of operation clear of all persons,
particularly small children, and pets.
d) Do not use a mower for any job except that for
which it is intended.
1.2 Preparation
a) Thoroughly inspect the area where the
equipment is to be used and remove all stones,
sticks, wires, bones, and other foreign objects.
b) Do not operate the equipment when barefoot
or wearing sandals. Always wear substantial
footwear.
c) Disengage the self-propelled mechanism
or drive clutch on units so equipped before
starting the motor.
d) Never attempt to make a wheel height
adjustment while the motor is running.
e) Mow only in daylight or in good artificial light.
f) Never operate the equipment on wet grass.
Always be sure of your footing. Keep a firm
hold on the handle and walk, never run.
1.3 Operation
a) Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
b) Stop the blade(s) when crossing gravel drives,
walks, or roads.
5
3-in-1 Cordless Lawn Mower EN
c) After striking a foreign object, stop the motor,
unplug, thoroughly inspect the mower for
any damage, and repair the damage before
restarting and operating the mower.
d) If the equipment should start to vibrate
abnormally, stop the motor and check
immediately for the cause. Vibration is generally
a warning of trouble.
e) Stop the motor and unplug whenever you leave
the equipment, before cleaning the mower
housing, and before making any repairs or
inspections.
f) Shut the motor off and wait until the blade
comes to a complete stop before removing the
grass catcher or before unclogging the chute.
g) Mow across the face of slopes, never up and
down. Exercise extreme caution when changing
direction on slopes. Do not mow excessively
steep slopes.
h) Never operate the mower without proper
guards, plates, or other safety protective
devices in place.
i) Do not wash with a hose, avoid getting water in
motor and electrical connections.
1.4 Maintenance
a) Check the blade and the motor mounting bolts
at frequent intervals for proper tightness.
b) Keep al nuts, bolts, and screws tight to be sure
the equipment is in safe working condition.
c) Check bag frequently for deterioration and
wear, and replace worn bags. Check that
replacement bags comply with the original
manufacturers recommendations or
specifications.
d) Replace the blade if it is bent or cracked. An
unbalanced blade causes vibration that could
damage the motor drive unit or cause personal
injury.
e) Sharpen a dull blade equally at each end to
maintain the balance.
f) Clear the blade thoroughly and check its
balance by supporting it horizontally on a thin
nail through its centre hole. The mail should
also be in a horizontal position. If either end
of the blade rotates downward, remove some
metal from the heavy or lower end until the
blade is balanced. It is balanced when neither
end drops.
SAVE THESE INSTRUCTIONS
6
3-in-1 Cordless Lawn Mower EN
SYMBOLS
KEEP HANDS AND FEET
AWAY
GARDER MAINS ET PIEDS À DISTANCE
CPSC Danger label
Severing of toes or fingers-Rotary
mower blade
Thrown objects from mower deck
Keep bystanders/children away
Safety alert
Slip on slope
Read the operator’s manual
Blade continues to rotate after the
machine is switched off. Wait until all
machine components have completely
stopped before touching them
Wear protective gloves
Li-Ion
Li-Ion battery, battery must be recycled
Remove battery from the socket before
carrying out any adjustment, servicing or
maintenance
Do not expose to rain or water.
Do not burn.
To reduce the risk of injury, user must
read instruction manual
Remove the key
POSITEC Inc. has established a
partnership with the RBRC Corporation
to recycle any Positec batteries with
the RBRC-call2recycle seal. For
environmental protection, please do
not discard batteries in the trash. After
the batteries’ life cycle is ended, then
please call 1.800-822-8837 for a free
service that will properly dispose of the
battery
7
3-in-1 Cordless Lawn Mower EN
1
6
8
9
12
11
10
2
7
4
5
3
8
3-in-1 Cordless Lawn Mower EN
1. OPERATING BAIL
2. SAFETY KEY
3. SAFETY FLAP
4. POWER INDICATOR LIGHT
5. BATTERY PACK COVER
6. CUTTING HEIGHT ADJUSTMENT LEVER
7. HANDLE KNOB
8. GRASS COLLECTION BAG
9. HANDLE BAR
10. SIDE-DISCHARGE COVER
11. SIDE-DISCHARGE CHUTE
12. MULCHING INSERT
13. BATTERY PACK* (SEE FIG. G2)
14. BLADE BOLT (SEE FIG. P1)
15. BLADE (SEE FIG. P1)
16. SPACER (SEE FIG. P1)
* Not all the accessories illustrated or described are included in standard delivery.
9
3-in-1 Cordless Lawn Mower EN
TECHNICAL DATA
WG751 WG751.9
Voltage 40V Max.(2x20V Max.)**
No load speed 2700 /min
Deck diameter 20" (51 cm)
Cutting diameter 19" (48 cm)
Front wheel diameter 7" (18 cm)
Rear wheel diameter 10" (25 cm)
Cutting height 1-1/4" ~ 4 " (3 – 10 cm)
Cutting height positions 7
Grass collection capacity 1.4 bushels (50 L)
Battery capacity 5.0 Ah (WA3579) /
Battery type Lithium-Ion /
Charger Model WA3884 /
Charger rating Input: AC 120V~60Hz
Output 1: 20 V , 2.0 A***
Output 2: 20 V , 2.0 A***
/
Charging time (approx.)
5.0 Ah (1 pc)
5.0 Ah (2 pcs)
1.25 hrs
2.5 hrs
/
Machine Weight 53.6 lbs (24.3 kg) 50.7 lbs (23 kg)
**Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is
18 volts.
** *Charger output 1 and output 2 mean two ports with the same output voltage and current.
ACCESSORIES
WG751 WG751.9
Battery pack (WA3579) 2 /
Charger (WA3884) 1 /
Grass collection bag 1
Mulching insert 1
Side-discharge chute 1
Only use the appropriate accessories intended for this tool. Accessory information can be found on the product
packaging, at a WORX dealer or on our website at www.worx.com.
10
3-in-1 Cordless Lawn Mower EN
2
11
1
1
1
1
2
2
2
2
3
4
13
1
2
E2 F
C2
D E1
A1
G1 G2
B
C3
A2
C1
11
3-in-1 Cordless Lawn Mower EN
2
11
1
1
1
1
2
2
2
2
3
4
13
1
2
E2 F
C2
D E1
A1
G1 G2
B
C3
A2
C1
12
3-in-1 Cordless Lawn Mower EN
15
16
14
1
2
3
4
5
6
7
1——1-1/4
(30mm)
2——1-1/2
(38mm)
3——2
(51mm)
4——2-1/2
(64mm)
5——3
(76mm)
6——3-1/2
(89mm)
7——4
(100mm)
1
2
O-1
O-2
O-3
11
100%
0%
J
O P1
P2
K1
K2
K3
L
M1
M2
N
H2
H1
13
3-in-1 Cordless Lawn Mower EN
15
16
14
1
2
3
4
5
6
7
1——1-1/4
(30mm)
2——1-1/2
(38mm)
3——2
(51mm)
4——2-1/2
(64mm)
5——3
(76mm)
6——3-1/2
(89mm)
7——4
(100mm)
1
2
O-1
O-2
O-3
11
100%
0%
J
O P1
P2
K1
K2
K3
L
M1
M2
N
H2
H1
14
3-in-1 Cordless Lawn Mower EN
ASSEMBLY & OPERATION
NOTE: Read instruction handbook before
operation this machine.
ASSEMBLY & OPERATION
Action Figure
ASSEMBLY
Assembling the handle bar See Fig. A1
Adjustment Handle’s height See Fig. A2
Assembling the grass collection bag See Fig. B
Assembling the grass collection bag to
the lawn mower
NOTE: Depress the grass collection
bag slightly to ensure that it is
completely installed.
NOTE: Take the mulching insert out
of the lawn mower before fitting the
grass collection bag.
See Fig. C1,
C2, C3
Removing/emptying grass collection
bag
WARNING! Always check the
safety flap close the discharge
outlet before using. Never lift the
safety flap when the lawn mower is
being used without fitted grass
collection bag.
See Fig. D
Installing side-discharge chute
See Fig. E1
E2
Installing mulching insert See Fig. F
Removing /fitting the battery pack
NOTE: This machine will only run
when 2 batteries are installed. It is
recommended to use the same two
batteries and charge the two batteries
at the same time.
When you use two batteries with
different power, the machine will
only run to the lower common
denominator.
See Fig. G1,
G2
Checking the battery charge
condition
NOTE: Fig. H1 only applies for the
battery pack with battery indicator
light.
See Fig. H1
Charging the battery pack
NOTE: The batteries are shipped
uncharged. Each battery must be fully
charged before the first mow.
Always fully charge the two batteries
at same time. More details can be
found in chargers manual.
See Fig. H2
OPERATION
Power indicator light
See details in BATTERY STATUS part
IMPORTANT:
When only one light is illuminated,
your battery is overly discharged,
even though the machine may still
be capable to work. Continuing
to operate your machine with
the battery in this discharged
condition may reduce the life and
performance of your battery.
When no light is illuminated,
at least one battery is not fully
installed or battery may be
defective, please double check
the batteries are fully seated into
position.
See Fig. J
Starting and Stopping
See Fig. K1,
K2, K3
Adjusting the cutting height
WARNING! Stop, release switch
lever and wait until the motor
stops before adjusting height. The
blades continue to rotate after the
machine is switched off, a rotating
blade can cause injury. Do not touch
rotating blades.
See Fig L
Storage
See Fig. M1,
M2
BATTERY STATUS (See Fig. J)
Before starting or after use, press the button
beside the power indicator light on the machine to
check the battery capacity.
15
16
14
1
2
3
4
5
6
7
1——1-1/4
(30mm)
2——1-1/2
(38mm)
3——2
(51mm)
4——2-1/2
(64mm)
5——3
(76mm)
6——3-1/2
(89mm)
7——4
(100mm)
1
2
O-1
O-2
O-3
11
100%
0%
J
O P1
P2
K1
K2
K3
L
M1
M2
N
H2
H1
15
3-in-1 Cordless Lawn Mower EN
During operation, the battery capacity will be
indicated automatically by the battery power
indicator. The indicator constantly senses and
displays the battery condition as follows.
For the machine with 2 battery packs with different
power, the power indicator light displays the battery
condition with the lower one of the two batteries.
Battery power
indicator status
Battery condition
Five green lights
( ) are
illuminated.
The two batteries are in a
highly charged condition.
Two, three or four
green lights are
illuminated.
The two batteries have a
remaining charge. The more
lights are illuminated, the
more battery capacity.
Only one green
light ( ) is
illuminated.
The battery level of at least
one battery pack is very low.
Please check and charge the
battery pack.
No light is
illuminated.
At least one battery is not fully
installed or battery may be
defective.
Only one light is
flashing twice per
cycle.
At least one battery is over
discharged (please refer to
the battery charge condition),
please recharge the two bat-
teries at once before use again
or storage.
Only one light
is flashing three
times per cycle.
At least one battery is hot,
wait for them cool down
before start again.
Only one light is
flashing four times
per cycle.
The machine is over load.
Raise the cutting height or
push slowly.
MULCHING MOWING TIPS
When using the mulching plug, your new mower is
designed to cut the grass clippings into small pieces and
distribute them back into the lawn, using mulching fins
located inside the mower deck.
Under normal conditions, the mulched grass will
biodegrade quickly to provide nutrients to the lawn. Please
review the following recommendations for optimum
mulching performance,
1) Avoid mowing when the grass is wet from rain
or dew. Wet grass may form clumps which
interfere with the mulching action and reduce
runtime. The best time to mow grass is in the
late afternoon when the grass is dry and the
newly cut area will not be exposed to direct
sunlight.
2) For best mulching performance, set the cutting
height to remove about one third of the grass
blade length, ideally no more than 1.5” inches
at one time. If the lawn is overgrown, it may be
necessary to increase the cut height to reduce
the pushing effort and prevent overloading
the motor. For extremely heavy mulching, it is
advisable to first cut at a high cut height setting,
and then re-cut to the final cut height. Otherwise,
make narrower cuts and mow slowly.
3) For best performance, keep the mower housing
free of built-up grass. From time to time turn
off mower and wait for the blade to come to a
complete stop. Then unplug the Safety Key(6)
and turn mower on its side. Using an object such
as a stick, wipe out any accumulation of grass
in the blade area. Be careful of the sharp edges
of the blade. Clean often in wet, new grass, and
always after every use.
4) Certain types of grass or grass conditions may
require that an area be mulched a second time
to fully disperse the grass throughout the lawn.
If cutting a second time, it is advisable to cut
perpendicular (across) the first cut pattern. DO
NOT CHANGE CUT PATTERN IN ANY WAY THAT
WOULD CAUSE MOWING DOWN A HILL.
5) Change your cutting pattern from week to week.
This will help prevent matting and graining of
the lawn.
CUTTING AREA
The cutting area can be affected by many factors
including: cutting height, operation practices (ex:
starting/stopping), lawn moisture levels, grass length
and thickness.
The below table provides the potential cutting areas
based on specific cutting conditions.
Cutting Height
Recommend lot size
(maximum)
Cutting off 3.3’’(8cm) to
2.5’’(6cm)
With 2*20V / 5.0Ah
batteries
up to 6500 sq.ft. (600m
2
) *
* Used with two fully charged battery packs.
TIPS:
1) Mowing the lawn frequently and reducing the amount
of starting/stopping procedures will help conserve
battery runtime. It is recommended to always use the
same two batteries during operation with fully charged
levels.
2) For the best cutting performance, it is recommended
to only mow up to 1/3 or less of the current grass height
at a time. Mow at a slower pace when cutting long/
thick grass to allow the mower to properly discharge the
clippings.
16
3-in-1 Cordless Lawn Mower EN
MAINTENANCE
WARNING: Stop the mower and remove
the safety key before removing the grass
collection bag.
NOTE: To ensure long and reliable service, perform
the following maintenance procedures regularly. Check
for obvious defects such as a loose, dislodged or a
damaged blade, loose fittings, and worn or damaged
components. Check that the covers and guards are
all undamaged and are correctly attached to mower.
Carry out any necessary maintenance or repairs before
operating mower. If the mower should happen to fail
despite regular maintenance, please call our customer
helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER
PERFORMANCE. A DULL BLADE DOES NOT CUT
GRASS CLEANLY OR MULCH PROPERLY.
WEAR PROPER EYE PROTECTION WHILE
REMOVING, SHARPENING, AND INSTALLING
BLADE. ENSURE THAT SAFETY KEY IS REMOVED.
Sharpening the blade twice during a mowing season
is usually sufficient under normal circumstances.
Sand causes the blade to dull quickly. If your lawn
has sandy soil, more frequent sharpening may be
required.
REPLACE BENT OR DAMAGED BLADE
IMMEDIATELY.
WHEN SHARPENING THE BLADE (See Fig. N)
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to
keep it balanced, removing equal amounts of
material from both ends.
NOTE:
1. Be sure the mower is turned off and remove the
key.
2. Place the mower in stand up storage mode.
BLADE BALANCING (See Fig. O)
Check balance of blade by placing center hole in
blade O-1 over a nail or screwdriver shank O-2,
clamped horizontally in a vise O-3. If either end of
the blade rotates downward, file that end. Blade is
properly balanced when neither end drops.
BLADE MAINTENANCE (See Fig. P1, P2)
Replace your metal Blade after 50 hours mowing
or 2 years, which ever is the sooner-regardless of
condition.
Follow these procedures to remove and replace the
Blade. You will need garden gloves (not provided)
and a spanner wrench (not provided) to remove the
Blade. Hold the Blade and unscrew the Blade Bolt
counter-clockwise using a spanner wrench, and then
remove the Blade.
To re-assemble, position the Blade with the cutting
edges towards the ground. Then securely tighten the
Blade Bolt.
STORAGE (SEE FIG. M1,
M2)
Stop the mower and always remove the Safety Key.
Clean the exterior of the machine thoroughly using
a soft brush and cloth. Do not use water, solvents or
polishes. Remove all grass and debris, especially from
the ventilation slots.
Turn the machine on its side and clean the blade area. If
grass cuttings are compacted in the blade area, remove
with a wooden or plastic implement.
Store the machine in a dry place. Do not place other
objects on top of the machine.
To aid storage, release the Handle knobs, and rotate or
fold the Upper Handle.
FOR BATTERY TOOLS
The ambient temperature range for the use and storage
of tool and battery is 0
o
C-45
o
C (32
o
F- 113
o
F).
The recommended ambient temperature range for the
charging system during charging is 0
o
C-40
o
C (32
o
F-
104
o
F).
17
3-in-1 Cordless Lawn Mower EN
TROUBLE SHOOTING
Problem Solution
1. Mower doesn’t run when
switch lever is activated.
A. Check to make sure safety key has been installed and is fully seated and
that button on switch housing is being completely pushed.
B. Release switch lever to turn mower off. Remove safety key, turn mower
over and check that blade is free to turn. If not free, return to an authorized
servicer. Blade should turn freely.
C. Has battery been fully charged? Plug in charger and wait for green light
to come on.
2. Motor stops while mowing. A. Release switch lever to turn mower off. Remove safety key, turn
mower over and check that blade is free to turn. If not free, return to an
authorized servicer. Blade should turn freely.
B. Raise cutting height of wheels to highest position and start mower.
C. Has battery been fully charged? Plug in charger and wait for green light
to come on.
D. Avoid overloading the mower. Slow down the cutting pace by pushing
mower slower or raise the cut height. Or both.
3. Mower runs but cutting
performance is unsatisfactory,
or does not cut entire lawn.
A. Has battery been fully charged? Plug in charger and wait for green
light to come on.
B. Release switch lever to turn mower off. Remove safety key. Turn
mower over and check: Blade for sharpness - Keep blade sharp. Deck and
discharge chute for clogging.
C. Wheel height adjustment may be set too low for grass condition. Raise
cutting height
4. Mower is too hard to push. A. Raise cutting height to reduce deck drag on grass. Check each wheel
for free rotation.
5. Mower is abnormally noisy
and vibrates.
A. Release switch lever to turn mower off. Remove safety key. Turn mower
on side and check blade to ensure it has not been bent or damaged. If
blade is damaged, replace with a replacement blade. If the underside of the
deck is damaged return mower to an Authorized service center.
B. If there is no visible damage to the blade and the mower still vibrates:
Release switch lever to turn mower off, remove safety key and remove
blade. Rotate blade 180 degrees and retighten. If mower still vibrates,
return the mower to an authorized service center.
6. Battery charger LED’s not on. A. Check plug connection.
B. Replace charger.
7. Battery charger LED does not
flip to green.
A. Battery needs to be diagnosed. Take to authorized service center.
8. Mower not picking up
clippings with the Grass
Collection Bag.
A. Remove mulch plate when bagging.
B. Chute clogged. Release switch lever to turn mower off. Remove safety
key. Clear chute of grass clippings.
C. Too much cut grass. Raise cutting height of wheels to shorten length of
the cut.
D. Bag full. Empty bag more often.
9. When mulching there are
clippings visible.
A. Too much cut grass. Raise cutting height of wheels to shorten length of
the cut. Do not cut off more than 1/3 of total length.
B. Check blade for sharpness. Always keep blade sharp.
10. Low or diminished
run-time after many uses
A. Return to Authorized Service location - may need new battery.
11. The battery charger LED
flashes red and the battery
can’t be charged.
A. The battery overheats after continuous use. Remove battery from the
charger and allow it to cool to 42
o
C or less.
18
Tondeuse à Gazon Sans Fil 3 en 1 F
CONSIGNES DE SÉCURITÉ
AVERTISSEMENT! Certaines des poussières
produites en utilisant des outils électriques
sont considérées par l’État de Californie comme
susceptibles de provoquer le cancer, des
anomalies congénitales et d’autres problèmes
de reproduction. Voici des exemples de ces
produits chimiques:
Plomb issu de peinture à base de plomb
Silice crystalline issue de briques et du
ciment et autres produits de maçonnerie
Arsenic et chrome issus de bois traité
chimiquement
Votre risque de ces expositions varie en
fonction de la fréquence à laquelle vous
effectuez ce travail. Pour réduire votre
exposition à ces produits chimiques : travaillez
dans une zone bien ventilée; portez un
équipement de sécurité approuvé, tel que des
masques antipoussières spécialement conçus
pour éliminer les particules microscopiques par
filtrage.
AVERTISSEMENT: Ce produit peut vous
exposer à des produits chimiques, incluant
au plomb, au phtalate ou au bisphénol A, qui
sont reconnus dans l’État de Californie comme
pouvant causer un cancer, des anomalies
congénitales ou d’autres dommages à l’appareil
reproducteur. Assurez-vous de bien vous laver
les mains après usage. Pour en savoir plus,
veuillez consulter le site www.P65Warnings.ca.
gov.
LISEZ ET LISEZ ET ASSIMILEZ TOUTES LES
INSTRUCTIONS
AVERTISSEMENT! Lors de l’utilisation
d’appareils électriques de jardinage, des
précautions de base doivent être observées afin de
réduire les risques de feu, choc électrique, et blessure
grave, incluant ce qui suit :
AVERTISSEMENT! L’emploi de la tondeuse
sans sac de ramassage peut provoquer des
risques de blessure.
AVERTISSEMENT! L’emploi de tout autre
accessoire ou dispositif est susceptible
d’augmenter les risques de blessure.
AVERTISSEMENT! Pour les tondeuses à
batterie, ne remplacez la batterie que par un
modèle de remplacement identique, du même type et
du même fabricant; installez également les accessoires
fournis pour retenir les rallonges électriques, le cas
échéant.
POUR TOUTES LES TONDEUSES À GAZON
1) Évitez les environnements dangereux.-N’utilisez
pas les appareils dans des endroits très humides
ou mouillés.
2) N’utilisez pas sous la pluie.
3) Tenez les enfants éloignés.-Tous les visiteurs
devraient être tenus éloignés de l’aire de travail.
4) Habillez-vous convenablement.-Ne portez pas
des vêtements lousses ou des bijoux. Ils peuvent
se prendre dans des pièces en mouvement.
L’utilisation de gants de caoutchouc et chaussures
épaisses est recommandée lors de travaux
extérieurs. Portez une protection pour cheveux
afin de contenir les cheveux longs.
5) Utilisez des lunettes de sécurité.-Toujours
porter un masque de visage ou de poussière si
l’opération est poussiéreuse.
6) Utilisez le bon appareil.-N’utilisez pas l’appareil
pour tout autre travail que pour celui auquel il est
destiné.
7) Ne forcez pas l’appareil-Il va faire un meilleur
travail et avec moins de risques de blessure en
travaillant au taux de charge pour lequel il a été
conçut.
8) N’essayez pas d’utiliser l’appareil hors de votre
portée normale.-Gardez votre équilibre et les
pieds bien ancrés en tout temps.
9) Restez alerte.-Faites attention à ce que vous
faites. Utilisez le bon sens. N’utilisez pas
l’appareil lorsque vous êtes fatigué.
10) Entreposez à l’intérieur les appareils qui ne
sont pas utilisés.-Lorsqu’inutilisés, les appareils
devraient êtres entreposés à l’intérieur dans un
endroit sec, élevé et gardé sous clef, hors de la
portée des enfants.
11) Entretenez les appareils avec soins.-Gardez les
arêtes de coupe aiguisées et propres pour une
meilleure performance et des risques réduits de
blessure. Suivez les instructions pour lubrifier
et changer les accessoires. Gardez les poignées
sèches, propres, et libres d’huile et graisse.
12) Maintenez les gardes en place et en bon ordre de
fonctionnement.
13) Gardez les lames aiguisées.
14) Gardez les mains et les pieds hors de l’aire
de coupe. Les objets frappés par la lame de la
tondeuse à gazon peuvent causer des blessures
graves aux gens.
15) La pelouse devrait toujours être examinée avec
soin et débarrassée de tous objets avant chaque
tonte.
16) Si la tondeuse à gazon frappe un corps étranger,
suivez ces étapes :
i) Arrêtez la tondeuse à gazon. Relâchez le
commutateur.
ii) Retrait du bloc de batterie.
iii) Inspectez pour dommages possibles.
iv) Réparez tout dommage avant de redémarrer et
d’opérer la tondeuse à gazon.
17) Utilisez seulement des lames identiques de
remplacement.
CONSIGNES DE SECURITE POUR TOUS LES
APPAREILS DE JARDINAGE FONCTIONNANT
AVEC UNE BATTERIE
1. Pour éviter le démarrage non intentionnel,
s’assurer que le bouton de démarrage est en
position d’arrêt avant de brancher l’appareil au
chargeur ou de le prendre ou de le transporter.
Un accident pourrait arriver si vous vous
promenez avec l’appareil avec le doigt sur
19
Tondeuse à Gazon Sans Fil 3 en 1 F
l’interrupteur ou sur le dispositif de charge dont
l’interrupteur est en position de charge.
2. Débranchez le bloc de batterie de l’appareil
avant de faire des réglages, de remplacer des
accessoires ou de ranger l’appareil. De telles
mesures de sécurité réduisent les risques de
démarrer l’appareil accidentellement.
3. Rechargez le bloc batterie uniquement avec le
chargeur spécifié par WORX. Un chargeur adapté
à un type de batterie peut entraîner un risque
d’incendie lorsqu’il est utilisé avec une autre
batterie.
4. Utilisez les appareils uniquement avec les
batteries spécifiquement indiquées. L’utilisation
de toute autre batterie pourrait créer un risque de
lésions et d’incendie.
5. Lorsque la batterie n’est pas utilisée, tenez la
à l’écart d’autres objets métalliques, tels que
les trombones, les pièces de monnaie, les
clefs, les clous, les vis ou d’autres petits objets
métalliques, qui peuvent établir la connexion
d’une borne à l’autre. Court-circuiter les bornes
de la batterie peut provoquer des brûlures ou un
incendie.
6. Dans des conditions d’utilisation abusive, du
liquide pourrait s’éjecter de la batterie; évitez
tout contact. Si vous entrez accidentellement en
contact avec le liquide, passez la partie du corps
touchée sous le robinet. Si vos yeux entrent en
contact avec le liquide, vous devez consulter
immédiatement un médecin. Le liquide expulsé
de la batterie peut causer des irritations ou des
brûlures.
7. Ne pas utiliser une batterie ou un appareil
qui est endommagé ou modifié. Les batteries
endommagées ou modifiées peuvent présenter
des comportements imprévisibles entraînant
un incendie, une explosion ou le risque de
blessures.
8. Ne pas exposer une batterie ou un appareil au
feu ou à une température excessive. L’exposition
au feu ou à une température au-dessus de 130°C
pourrait causer une explosion.
9. Respecter toutes les consignes de charge et ne
pas charger la batterie ou l’appareil en dehors
de laplage de température indiquée dans les
consignes. Mal charger ou à des températures en
dehors de la plage indiquée peut endommager la
batterie et accroître le risque d’incendie.
10. Faites faire le service par un technicien de
réparation compétent qui ne doit utiliser que des
pièces de rechange identiques. Ceci maintiendra
la sécurité du produit.
11. Ne pas modifier ou essayer de réparer l’appareil
ou la batterie (selon le cas) sauf comme indiqué
dans les consignes d’utilisation et d’entretien.
CONSIGNES GÉNÉRALES DE SÉCURITÉ
CONCERNANT LA BATTERIE
a) Ne pas démonter, ouvrir ou déchiqueter le
bloc batterie.
b) Ne pas exposer le bloc batterie à la chaleur
ou au feu. Evitez de ranger la batterie dans
un endroit exposé à la lumière directe du
soleil.
c) Ne pas court-circuiter une batterie. Ne
stockez pas les blocs batterie en vrac
dans une boîte ou un tiroir où ils peuvent
se court-circuiter ou être court-circuités
par d’autres objets métalliques. Lorsque
le bloc batterie n’est pas utilisé, conservez-le
loin d’autres objets métalliques, tels que des
trombones, des pièces de monnaie, des clés, des
clous, des vis ou d’autres objets métalliques de
petite taille, qui pourraient établir une connexion
d’un terminal à l’autre. Le fait de créer un court-
circuit entre les bornes de la batterie peut causer
des brûlures ou des incendies.
d) Ne pas retirer la batterie de son emballage
d’origine avant utilisation dans l’appareil.
e) Ne pas soumettre la batterie à des chocs
mécaniques.
f) En cas de fuite de la batterie, ne pas laisser
le liquide entrer en contact avec la peau ou
les yeux. Si un contact a été effectué, laver
la zone touchée avec beaucoup d’eau et
consulter un médecin.
g) Respecter les marques plus (+) et moins
(-) sur le bloc batterie et sur l’appareil et
veiller à bien le positionner.
h) Ne pas utiliser de batterie qui n’a pas été
conçue pour être utilisée avec cet appareil.
i) Maintenez la batterie hors de portée des
enfants.
j) Consultez immédiatement un médecin si
une cellule ou une batterie a été avalée.
k) Achetez toujours une batterie
recommandée par le fabricant de l’appareil.
l) Conservez le bloc batterie propre et sec.
m) Essuyez les bornes de la batterie avec un
chiffon propre et sec si elles deviennent
sales.
n) La batterie doit être chargée avant son
utilisation. Utilisez toujours le chargeur
adapté et reportez-vous aux instructions
du fabricant ou au manuel de l’équipement
pour suivre les instructions concernant la
procédure de charge.
o) Ne laissez pas le bloc batterie en charge
prolongée lorsqu’il n’est pas utilisé.
p) Après de longues périodes de stockage,
il peut être nécessaire de charger et de
décharger la batterie plusieurs fois pour
obtenir des performances optimales.
q) La batterie offre de meilleures
performances lorsqu’elle est utilisée à
température ambiante normale (68 °F ± 9
°F).
r) Lors de l’élimination des batteries,
conservez les blocs batteries de différents
systèmes électrochimiques séparés les uns
des autres.
s) Rechargez le bloc batterie uniquement
avec le chargeur spécifié par WORX.
N’utilisez pas un chargeur autre que celui
spécifiquement conçu pour être utilisé avec
20
Tondeuse à Gazon Sans Fil 3 en 1 F
l’équipement. Un chargeur adapté à un type
de batterie peut entraîner un risque d’incendie
lorsqu’il est utilisé avec une autre batterie.
t) Conservez la documentation originale du
produit pour référence ultérieure.
u) Utilisez uniquement la batterie dans
l’application pour laquelle elle a été prévue.
v) Retirez la batterie de l’équipement lorsqu’il
n’est pas utilisé.
w) Éliminez la batterie de façon adéquate.
INSTRUCTIONS DE SÉCURITÉ POUR LES
TONDEUSES POUSSÉES
IMPORTANT
INSTRUCTIONS DE SÉCURITÉ POUR LES
TONDEUSES POUSSÉES
I. FONCTIONNEMENT GÉNÉRAL
1. Lisez, comprenez et suivez toutes les instructions
concernant la machine et contenues dans le(s)
manuel(s) avant de démarrer.
2. Ne placez pas les mains ou les pieds à proximité
de la machine ou en dessous. Restez à distance
de l’ouverture d’éjection à tout instant.
3. N’autorisez que des adultes responsables qui
sont familiers avec les instructions à opérer cette
machine.
4. Dégagez la zone d’objets comme des pierres, des
câbles ou des jouets, etc.…, qui pourraient être
propulsés par la lame. Restez derrière la poignée
quand le moteur tourne.
5. Assurez-vous qu’il n’y a pas de spectateurs dans
la zone avant l’opération. Arrêtez la machine si
quelqu’un pénètre dans la zone.
6. N’opérez pas la machine pieds nus ou si vous
portez des sandales. Portez toujours des
chaussures robustes.
7. Ne tirez pas la machine en arrière, à moins que ce
soit indispensable. Regardez toujours vers le bas
et en arrière avant et pendant un déplacement en
arrière.
8. Ne dirigez jamais les matériaux éjectés vers
quelqu’un. Évitez d’éjecter des matériaux contre
un mur ou un obstacle. Les matériaux peuvent
ricocher sur l’opérateur. Arrêtez la lame lorsque
vous traverser des surfaces de gravier.
9. N’opérez pas la machine sans le ramasse-herbe,
la chicane de décharge, la protection arrière
ou autres dispositifs de protection de sécurité
complets en place et en fonctionnement.
10. Ne laissez jamais une machine fonctionner sans
surveillance.
11. Arrêtez le moteur et attendez que la lame s’arrête
totalement avant de nettoyez la machine, de
retirer le ramasse-herbe ou de dégager la chicane
de décharge.
12. Opérez la machine à la lumière du jour ou sous
un bon éclairage artificiel uniquement.
13. N’opérez pas la machine lorsque vous êtes sous
l’influence d’alcool ou de médicaments.
14. N’opérez jamais la tondeuse dans de l’herbe
humide. Soyez toujours sûr(e) de votre appui ;
marchez, ne courez jamais.
15. Débrayez le système d’entraînement, s’il y a,
avant de démarrer le moteur.
16. Si la machine se met à vibrer de manière
anormale, arrêtez le moteur et vérifiez
immédiatement la cause. Les vibrations
indiquent généralement un problème.
17. Portez toujours une protection pour les yeux
quand vous opérez la machine.
18. Consultez les instructions du fabricant pour
installer et opérer les accessoires de manière
appropriée. N’utilisez que les accessoires
approuvés par le fabricant.
II. FONCTIONNEMENT DANS UNE PENTE
Les pentes constituent un facteur majeur d’accidents
par glissage et par chute, ce qui peut entraîner des
blessures graves. Opérer dans des pentes exige une
prudence extrême. Si vous ne vous sentez pas à l’aise
dans une pente, ne la tondez pas.
1. Tondez la surface des pentes transversalement,
jamais de haut en bas ou vice-versa. Soyez
extrêmement vigilent(e) lorsque vous changez de
sens dans des pentes.
2. Faites attention aux trous, ornières, bosses,
pierres ou autres objets dissimulés. Un terrain
inégal peut entraîner un accident par glissade
et par chute. L’herbe haute peut dissimuler des
obstacles.
3. Ne tondez pas de l’herbe humide ou dans des
pentes excessivement raides. De mauvaises
chaussures peuvent entraîner un accident par
glissade et par chute.
4. Ne tondez pas à proximité de fossés, de rigoles
ou de remblais. Vous pourriez perdre appui ou
perdre l’équilibre.
III. ENFANTS
Des accidents graves peuvent survenir si l’opérateur
n’est pas alerté de la présence d’enfants. Les enfants
sont souvent attirés par la machine et par l’activité de
tonte. Ne supposez jamais que des enfants resteront
au dernier endroit où vous les avez vus.
1. Gardez les enfants à distance de la zone de tonte
et sous la surveillance d’un adulte responsable
autre que l’opérateur.
2. Soyez alerté(e) et éteignez la tondeuse si un
enfant pénètre dans la zone.
3. Ne laissez jamais les enfants opérer la machine.
4. Soyez extrêmement prudent(e) lorsque vous
vous approchez de tournants sans visibilité,
d’arbustes, d’arbres ou autres objets qui
pourraient vous empêcher de voir la présence
d’un enfant.
IV. ENTRETIEN
ENTRETIEN GÉNÉRAL
1. Gardez tous les écrous et les boulons serrés
pour être certain(e) que l’état de marche de
l’équipement est sécurisé.
2. N’altérez jamais des dispositifs de sécurité.
Vérifiez régulièrement qu’ils fonctionnent
correctement.
3. Ne laissez pas d’herbe, de feuilles ou autres
débris s’accumuler dans la machine.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Worx WG751.2 Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues