Hikoki M3612DA Manuel utilisateur

Model

Modèle

Modelo M 3612DA Cordless router

Détoureuse sans ﬁ l

Fresadora inalámbrica

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should be

stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

2

English

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all of the safety precautions, warnings and operating instructions in the instruction manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this instruction manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this instruction manual.

Never use this power tool in a manner that has not been speciﬁ cally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

3

English

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal

injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ

re.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

4

English

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting tool may contact hidden wiring.

Contact with a “live” wire will also make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

2. Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by your hand or against the body

leaves it unstable and may lead to loss of control.

3. Always wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity noise

can cause hearing loss.

4. Handle the bits very carefully.

5. Check the bit carefully for cracks or damage

before operation. Replace cracked or damaged

bit immediately.

6. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

7. Hold the tool ﬁ rmly with both hands.

8. Keep hands away from rotating parts.

9. Make sure the bit is not contacting the workpiece

before the switch is turned on.

10. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate improperly installed bit.

11. Be careful of the bit rotating direction and the

feed direction.

12. Do not leave the tool running. Operate the tool

only when hand-held.

13. Always switch oﬀ and wait for the bit to come to

a complete stop before removing the tool from

workpiece.

14. Do not touch the bit immediately after operation:

it may be extremely hot and could burn your skin.

15. After changing the bits or making any

adjustments, make sure the collet chuck and any

other adjustment devices are securely tightened.

Loose adjustment device can unexpectedly shift,

causing loss of control, loose rotating components

will be violently thrown.

16. Always wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

17. Deﬁ nitions for symbols used on this tool

V ..............volts

--- ............direct current

Hz ............hertz

n0 .............no load speed

---/min ...... revolutions or reciprocation per minute

18. Because the cordless router operates by battery

power, be aware of the fact that it can begin to operate

at any time.

19. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

20. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

IMPORTANT SAFETY INSTRUCTIONS

FOR CHARGER OR ADAPTER

The term “charger or adapter” in the safety instructions

refers to your battery charger or AC/DC adapter.

WARNING

Death or serious bodily injury could result from

improper or unsafe use of charger or adapter.

To avoid these risks, follow these basic safety

instructions:

5

English

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YSL3 or

AC/DC adapter Model ET36A.

2. Before using charger or adapter, read all instructions

and cautionary markings on (1) charger or adapter, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable battery models of the multi volt series.

Other models of batteries may burst causing personal

injury and damage.

4. Use of an attachment not recommended or sold by

the charger or adapter manufacturer may result in a

risk of ﬁ re, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting charger or adapter.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

charger or adapter:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of charger or adapter as speciﬁ ed in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR CHARGER OR ADAPTER

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than but less

than

Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a charger or adapter is given in

watts rather than in amperes, the corresponding

ampere rating is to be determined by dividing the

wattage rating by the voltage rating–for example:

1,250 watts = 10 amperes

125 volts

8. Do not operate charger or adapter with damaged cord

or plug-replace them immediately.

9. Do not operate charger or adapter if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble charger or adapter; take it to

a qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

11. To reduce risk of electric shock, unplug charger

or adapter from receptacle before attempting any

maintenance or cleaning. Removing the battery will

not reduce this risk.

12. This AC/DC adapter is for use only with speciﬁ c tools,

including M3612DA. The adapter might be suitable for

use with other metabo HPT battery operated tools. It

is necessary to conﬁ rm suitability by referencing the

instruction manual of the speciﬁ c tool or by consulting

our web site https://www.metabo-hpt.com/. Failure

to conﬁ rm suitability before using the adapter with

speciﬁ c tools could result in ﬁ re hazard.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

CHARGER OR ADAPTER

You must charge the battery before you can use the power

tool. Before using the model UC18YSL3 battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

REMEMBER: USE ONLY metabo HPT BATTERY

MODELS OF THE MULTI VOLT SERIES. OTHER

MODELS OF BATTERIES MAY BURST AND CAUSE

INJURY!

Follow these instructions to avoid the risk of injury:

WARNING

Improper use of the battery or battery charger

can lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery or AC/DC adapter.

2. NEVER incinerate the battery or AC/DC adapter, even

if it is damaged or is completely worn out. The battery

can explode in a ﬁ re.

3. NEVER short-circuit the battery or AC/DC adapter.

6

English

4. NEVER insert any objects into the charger or

adapter’s air vents. Electric shock or damage to the

charger or adapter may result.

5. NEVER use outdoors. Keep the battery or AC/DC

adapter away from direct sunlight and use only where

there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 14°F

(-10°C) or above 104°F (40°C). (UC18YSL3)

NEVER use when the temperature is below 32°F

(0°C) or above 104°F (40°C). (ET36A)

7. NEVER connect two charger or adapter together.

8. NEVER insert foreign objects into the hole for the

battery or the charger or adapter.

9. NEVER use a booster transformer.

10. NEVER use DC power.

11. NEVER store the battery or charger or adapter in

places where the temperature may reach or exceed

104°F (40°C) such as inside metal box or car.

12. NEVER expose the battery or charger or adapter to

rain or wet conditions.

13. ALWAYS operate charger or adapter on standard

household electrical power (120 volts). Using the

charger or adapter on any other voltage may overheat

and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger or adapter is not in use.

[The information below applies only to ET36A]

16. Do not use the product if the tool or the AC/DC adapter

terminals (AC/DC adapter mount) are deformed.

Installing the AC/DC adapter could cause a short

circuit that could result in smoke emission or ignition.

17. Keep the tool’s terminals (AC/DC adapter mount) free

of swarf and dust.

○ Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○ During use, try to avoid swarf or dust on the tool from

falling on the AC/DC adapter.

○ When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

18. The product is intended for Use in Pollution Degree

2 or PD2 environments. Operate only in areas of

non-conductive pollution. A temporary conductivity

caused by condensation is normally expected.

19. This is a precision machine so do not drop or expose

to impact.

20. Do not use this product near a pacemaker or other

similar implanted device, which may be aﬀ ected by a

magnetic ﬁ eld produced by this product.

21. The adapter, power supply box and the inside of the

DC cord generates a boosted high voltage of 380 V so

please be careful of the following.

○

Do not disassemble the product.

○

Do not drop or expose to impact.

In the event the product is damaged from strong

impact, do not use the product.

○

Do not use the product in areas exposed to rain,

snow, iron powder or wet condition.

○

Do not touch the product with wet hands.

○

Do not spill or pour liquid onto the product.

○

Do not pull the cord with excessive force.

○

Use the product in a well-ordered work environment.

CAUTION

1. When the mesh of the vent is plugged by objects such

as wood shavings, try to keep the objects out when

you clear the mesh.

(If not properly maintained, the temperature protective

feature could shut the product oﬀ )

2. When the temperature protective feature frequently

cuts the power oﬀ , do not overload the machine with

continued work, but let the machine rest for a little

before continuing operation.

3. The machine does get hot. However, this does not

indicate an abnormality.

Keep the electricity running and operate the internal

fan to cool the machine before carrying it elsewhere.

When carrying the product, make sure to use the cord

armor. The case may be hot so please be careful.

4. During use, do not pull the cord to move the Box.

Doing so may result in damage.

5. Do not use more that a single cord reel of 30 meters.

Doing so may result in damage.

6. During use, if the machine stops running after the

Box’s LED lamp blinks, conﬁ rm the power supply

environment.

7. Do not drag the cord when using or carrying the

machine.

Doing so may tear the cord insulation or break the

cord which could result in electric shock.

8. Do not stretch the cord out any more than required.

When using tools such as gardening clippers or

circular saws, always make sure of the power cord’s

position to avoid cutting the cord during operation.

9. To use the AC/DC adapter after it shuts down due to

high temperature, disconnect the box’s power plug,

wait for the LED lamp to go out and then reconnect

the box’s power plug.

If the machine cuts oﬀ even after suﬃ ciently cooling it

oﬀ with the built-in fan, discontinue use as there may

be a problem with the machine.

10. Do not use this product near a radio. Doing so could

cause noise from the radio, making it diﬃ cult to listen

to a broadcast.

7

English

11. This is a power source for multi volt products. Do not

use with 18 V products or chargers. Doing so could

result in damage.

12. Overload behavior may diﬀ er when compared with

BSL36B18 battery use.

With the battery where the LED should blink on the

main unit, the LED on the AC/DC adapter may blink

instead.

PRECAUTIONS FOR AC/DC ADAPTER

The adapter equips with the protection function to stop the

output. In the cases of 1 to 2 described below, when using

this product, even if you are pulling the switch, the motor

may stop. This is not the trouble but the result of protection

function.

1. If the tool is overloaded, output may stop. In this case,

release the switch of tool and eliminate causes of

overloading.

2. If the adapter is overheated under overload work,

output may stop. In situations like this, discontinue

use of the adapter and detach it from the tool. Allow

the adapter to cool in a location such as a shaded

area with good air circulation.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible

and ﬂ ammable items. Corrosive gas atmospheres

must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

8

English

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (Fig. 3).

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

●

If the BSL36B18 is installed in the power tool, the

power output will exceed 100 Wh and the unit

will be classiﬁ ed as Dangerous Goods for freight

classiﬁ cation.

Wh

Power Output

2 to 3 digit number

Fig. 1

USB DEVICE CONNECTION

PRECAUTIONS

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

9

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this instruction manual is designed to assist you in the safe operation and maintenance

of the power tool.

Never operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this instruction manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless router (M3612DA)

Stopper pole

Depth

indicator

Wing bolt

Stopper block

Sub base

Collet chuck Wing bolt (A)

Lock spring

Straight guide

Lock pin

Dial

Head cover

Battery Motor

Base

With straight guide attached

Name plate

Handle

Threaded column Dust Collector

Hose

(Cleaner) LED light

Lock lever

Switch trigger

ON/OFF

Lock button

Rearview/without straight guide

Fig. 2

2. Battery 3. Battery Charger 4. AC/DC Adapter

(optional accessories…sold separately)

Battery Latch

Ventilation holes

Terminals

Battery cover

Ventilation

holes

Body

Cord

Nameplate

Charge

indicator lamp

Guide rail

Plug

Latch

Ventilation holes

Terminals

AC cord

DC cord

Box

Cord armor

Adapter

Error lamp

Power

lamp

Fig. 3

Fig. 4

<ET36A>

Fig. 5

10

English

SPECIFICATIONS

1. Cordless router

Model M3612DA

Motor DC brushless motor

Collet chuck capacity 1/2" (12.7 mm), 1/4" (6.35 mm)

Main body stroke 1-31/32" (50 mm)

No-load speed 11,000–25,000 /min

Battery* Type* Li-ion battery Model BSL36A18X /

AC/DC adapter Model ET36A (sold separately)

Voltage DC 36 V / 18V

Weight 8.4 lbs (3.8 kg)

(BSL36A18X and dust collector attached)

* Existing batteries (BSL3660/3626/3620, BSL18xx and BSL14xx series, etc.) cannot be used with this tool.

If using the AC/DC adapter, please read and understand its manual before operating the power tool.

NOTE

Available bit: Straight bits, Flush trimming bits, Chamfering bits, Round-over bits, Rabbeting bits, Dovetail bits.

2. Battery Charger

Model UC18YSL3

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C)) BSL36A18X : Approx. 32 min

Charging voltage DC 14.4–18 V

Charging current DC 8.0 A

Weight 1.3 lbs. (0.6 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

3. AC/DC Adapter

Model ET36A

Input power source Single phase: AC 120 V 60 Hz

Output voltage 36 V

Operating temperature range 14°F (-10°C)–104°F (40°C)

Weight Adapter : 1.8 lbs. (0.8 kg)

Box : 2.6 lbs. (1.2 kg)

11

English

ASSEMBLY AND OPERATION

APPLICATIONS

○

Woodworking jobs centered on grooving and

beveling.

For example, grooving beveling, cutting, copying,

engraving, shape cutting, combinations and others.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

○

How to install the battery.

Align the battery with the groove in head cover and

slip it into place.

Always insert it all the way until it locks in place with a

little click. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 6).

○

How to remove the battery.

Withdraw battery from the head cover while pressing

the latch (2 pcs) of the battery (Fig. 6).

Latch

Battery

InsertPull out

Push

Head cover

Fig. 6

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○ The power source voltage is stated on the nameplate.

○ The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn out.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charge

indicator lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Firmly Insert the battery into the battery charger as

shown in Fig. 7.

Charge

indicator lamp

Guide rail

Battery

Fig. 7

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the

charge indicator lamp will light up in green.(See

Table 2)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 2, according to the condition of the

battery charger or the battery.

12

English

Table 2

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging Blinks

(RED)

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds) Plugged into power

source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light for 1 second.

(oﬀ for 1 second) Battery capacity at less

than 50%

Blinks

(BLUE)

Lights for 1 second. Does not light for 0.5 seconds.

(oﬀ for 0.5 seconds) Battery capacity at less

than 80%

Lights

(BLUE) Lights continuously Battery capacity at more

than 80%

Charging

complete Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about 6 seconds)

Overheat

standby Blinks

(RED)

Lights for 0.3 seconds. Does not light for

0.3 seconds. (oﬀ for 0.3 seconds)

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Charging

impossible Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about 2 seconds)

Malfunction in the

battery or the charger

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 3

Rechargeable

batteries Temperatures at which the battery

can be recharged

BSL36A18X 32°F–122°F

(0°C–50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time

Charger

Battery UC18YSL3

BSL36A18X Approx. 32 min

NOTE

The recharging time may vary according to the

ambient temperature.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

Be sure to pull out the battery from the battery charger

after use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2–3 times.

13

English

NOTE

○

The time required for charging will be longer when

a USB device and battery are being simultaneously

charged.

○

There may be an occasional pause during USB

recharging.

○

When a USB device is not being charged, turn the

USB power switch OFF and remove the USB device

from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

(1) Select a charging method

Depending on the charge method selected, either the

battery is inserted into the charger or the power cord

is plugged into an outlet.

○

Charging a USB device by battery (Fig. 8-a)

○

Charging a USB device from a electrical outlet

(Fig. 8-b)

○

Charging a USB device and battery from a

electrical outlet (Fig. 8-c)

abc

Fig. 8

(2) Turn the USB power switch ON (Fig. 9)

When you turn the USB power switch ON, the USB

power indicator lamp will light up.

USB power

switch

USB power

indicator lamp

Rubber cover

USB port

USB cable

Fig. 9

(3) Connect the USB cable. (Fig. 9)

Pull back the rubber cover and ﬁ rmly plug in a

commercially available USB cable (appropriate to the

device being charged) into the USB port.

○

When the power cord is not plugged into an outlet and

the battery runs out of power, power output will stop

and the USB power indicator lamp will shut oﬀ .

○

When the USB power indicator lamp goes out, change

the battery or plug the power cord into an electrical

outlet.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated because

it has been left for a long time in a location subject

to direct sunlight or because the battery has

just been used, the charge indicator lamp of the

charger lights for 0.3 seconds, does not light for

0.3 seconds (oﬀ for 0.3 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

●

When the charge indicator lamp ﬂ ickers (at

0.2–second intervals), check for and take out

any foreign objects in the charger’s battery

installation hole. If there are no foreign objects,

it is probable that the battery or charger is

malfunctioning. Take it to your authorized

Service Center.

HOW TO RECHARGE USB DEVICE

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○

Prior to use, check the connecting USB cable for

any defect or damage.

Using a defective or damaged USB cable can

cause smoke emission or ignition.

○

When the product is not being used, cover the

USB port with the rubber cover.

Buildup of dust etc. in the USB port can cause

smoke emission or ignition.

14

English

(4) When charging is completed

○

The USB power indicator lamp will not go out when a

USB device has been completely charged.

To verify charge status, check the USB device.

○

Turn the USB power switch OFF and unplug the power

cord from the electrical outlet. (Fig. 9)

○

Remove the battery from the charger and place the

rubber cover over the USB port.

BEFORE USE

WARNING

To avoid serious accident, ensure the switch is in

the OFF position, and pull out the battery.

1. Check the work area environment

Check the work area to make sure that it is clear of

debris and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

2. Secure the material with a vice to ensure that both

hands are free to hold and operate the power tool.

(Fig. 10)

Fig. 10

3. Power switch

Ensure that the switch is in the OFF position.

INSTALLING AND REMOVING BITS

WARNING

To avoid serious accident, ensure the switch is in

the OFF position, and pull out the battery.

Use the included 23 mm wrench to tighten the

collet chuck.

Use of tools other than the included can result in

over or under-tightening which may cause injury.

1. Installing bits

(1) Loosen the lock lever (Fig. 2), raise the tool to the

maximum stroke position and return the lock lever to

the tightening position.

(2) Clean and insert shank of bit into the collet chuck until

shank bottoms, then back it out approximately 1/16"

(approx. 2 mm).

(3) With the bit inserted and pressing the lock pin holding

the shaft, use the 23 mm wrench to ﬁ rmly tighten the

collet chuck in a clockwise direction (viewed from

under the router). (Fig. 11)

Lock pin

23 mm Wrench

Loosen

Collet chuck Bit

Tighten

Fig. 11

When using the 1/4" (6.35 mm) diameter shank bit, replace

the equipped collet chuck with the one for 1/4" (6.35 mm)

diameter shank bit which is provided as the standard

accessory. (Fig. 12)

Lock pin

Tighten

Shaft

Collet chuck

Loosen

Fig. 12

NOTE

○

Ensure that the collet chuck is ﬁ rmly tightened

after inserting a bit. The collet chuck may become

deformed if the collet chuck is tightened without a bit

set in place.

○

Ensure that the lock pin is not inserted into the shaft

after tightening the collet chuck. Failure to do so will

result in damage to the collet chuck, lock pin and

shaft.

○

Use only router bits of which the maximum speed, as

indicated on the bit, does exceed the maximum speed

of the router.

2. Removing bits

(1) Loosen the lock lever, raise the tool to the maximum

stroke position and return the lock lever to the

tightening position.

(2) Pressing the lock pin, loosen the collet chuck with the

included 23 mm wrench to pull out the bit.

15

English

(4) Tighten wing bolt. Align the depth indicator with the

“0” graduation of scale. (Fig. 15 (a))

(5) Loosen wing bolt, and raise until indicator aligns

with the graduation representing the desired cutting

depth. Tighten wing bolt. (Fig. 15 (b))

(b)(a)

“0”

Fig. 15

(6) Loosen the lock lever and press the tool body down

until the stopper block to obtain the desired cutting

depth.

As shown in Fig. 16 (a), loosening the two nuts on the

threaded column and moving them down will allow you to

move down to the end position of the bit when the lock

lever was loosened. This is helpful when moving the

router to align the bit with the cutting position. As shown

in Fig. 16 (b), tighten the upper and lower nuts to secure

the cutting depth.

(b)(a)

Nuts

Threaded

Column

Fig. 16

NOTE

○

Raise the power tool to the upper limit position and

make sure that the bit is not touching the material.

○

The two nuts attached to the base are for securing

threaded column. Do not loosen the nuts. Also,

check to see if they are loose and tighten them when

necessary.

PRIOR TO OPERATION

WARNING

To avoid serious accident, ensure the switch is in

the OFF position, and pull out the battery.

1. Adjusting depth of cut

(1) Place the tool on a ﬂ at wood surface.

(2) Loosen wing bolt allowing the stopper pole to contact

with stopper block. (Fig. 13)

Depth indicator

Wing bolt

Stopper pole

Stopper block

Scale

Fig. 13

(3) Loosen the lock lever and press the tool body until the

bit just touches the ﬂ at surface. Tighten the lock lever

at this point.

Tighten the wing bolt and also secure the stopper

pole. (Fig. 14)

Lock lever

Wing bolt

Stopper pole

Fig. 14

16

English

The 2 cut-depth setting screws attached to the

stopper block can be adjusted to simultaneously set

3 diﬀ erent cutting depth. Use a wrench to tighten the

nuts so that the cut-depth setting screws do not come

loose at this time.

Screw driver

Nut

Cut depth

setting screw

Stopper block

Fig. 17

NOTE

○

When you are not using the stopper pole to set the

cutting depth, push up the stopper pole so that it is not

in the way.

○

Please limit the cutting depth of a single cut to under

13/16" (20 mm).

2. Guiding the router

WARNING

To avoid serious accident, ensure the switch is in

the OFF position, and pull out the battery.

Use the template guide when employing a template

for producing a large quantity of identically shaped

products.

As shown in Fig. 18, secure the template guide to the

base of the router with two accessory screws. At this

time, ensure that the projection side of the template

guide is facing the bottom surface of the base of the

router.

Template guide

Projection

Screw

Fig. 18

A template is a proﬁ ling mold made of plywood or

thin lumber. When making a template, pay particular

attention to the matters described below and

illustrated in Fig. 19.

When using the router along the interior plane of

the template, the dimensions of the ﬁ nished product

will be less than the dimensions of the template by

an amount equal to dimension “A”, the diﬀ erence

between the radius of the template guide and the

radius of the bit. The reverse is true when using the

router along the exterior of the template.

Bit

Template guide Template

A

Fig. 19

Secure the template to the workpiece. Feed the router

in the manner that the template guide moves along

the template as shown in Fig. 20.

Fig. 20

Use of the template guide adapter is required when

using the template guides produced by other ﬁ rms

with a portion of the standard accessories. The

template guide adaptor, like the template guide, is

attached to the base with two accessory screws.

Attach template guides made by other ﬁ rms to the

template guide adaptor.

Template guide

adaptor

Template guide

Template

guide

Template guide

Fig. 21

17

English

Use straight guide for chamfering and groove cutting

along the materials side. (Fig. 22)

Guide bar

Guide plane

Straight guide

Wing bolt (A)

Wing bolt (B)

Feed screw

Bar holder

Fig. 22

(1) Insert a guide bar into each hole in the bar holder, then

lightly tighten the 2 wing bolts (A) on top of the bar

holder.

(2) Insert a guide bar into each hole in the base, then ﬁ rmly

tighten the wing bolts (A) (standard accessories).

(3) Make minute adjustments of the dimensions between

the bit and the guide surface with the feed screw, then

ﬁ rmly tighten the 2 wing bolts (A) on top of the bar

holder and the wing bolt (B) that secures the straight

guide.

(4) As shown in Fig. 23, securely attach the bottom of the

base to processed surface of the materials. Feed the

router while keeping the guide plane on the surface of

the materials.

Fig. 23

NOTE

When using the straight guide, be sure to install it on

the right side in the feed direction. This will help to

keep it ﬂ ush with the side of the workpiece.

Connect the dust collector set cleaner to collect dust.

(1) Mounting the dust collector.

Use a screwdriver to attach the two screws to the

base. (Fig. 24)

Screw

Dust Collector

Knob nut

Fig. 24

Align the holes on the dust collector with the two

screws and attach the dust collector.

Tighten the two knob nuts.

Connect the cleaner to the dust collector. (Fig. 25)

Dust Collector

Hose (Cleaner)

Fig. 25

(2) Dismounting the dust collector.

Use a screwdriver to loosen the two screws.

OPERATION

WARNING

●

To avoid serious accident, ensure the switch is in

the OFF position, and pull out the battery.

●

Wear eye protection when operating this tool.

●

Keep your hands, face and other body parts

away from the bits and any other rotating parts,

while operating the tool.

CAUTION

●

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the

causes of overloading.

●

Pull out the battery after completing operation.

18

English

1. Switch operation

This product is equipped with an ON/OFF Lock button

to prevent any inadvertent switch trigger operation. To

activate the tool, press down on the ON/OFF Lock

button and draw the switch trigger. (Fig. 26)

Switch

trigger

ON/OFF

Lock button

Fig. 26

When the switch trigger is fully drawn, a further

press of the ON/OFF Lock button will lock the switch

trigger in place, allowing the release of the switch

trigger for continued operation. (Fig. 27 (a))

The switch trigger will not be locked if the ON/OFF

Lock button is released before the switch trigger is

fully drawn, making it possible to operate the tool with

a press of the switch trigger.

To unlock the switch trigger, draw the switch trigger

once again to release the ON/OFF Lock button and

discontinue operation. (Fig. 27 (b))

Prior to using the tool, make sure that the ON/OFF

Lock button and the switch trigger are operating

properly.

(b)(a)

Fig. 27

2. How to use the LED light (Fig. 28)

The LED light will light the area at the tip of the tool

when the switch is “ON”.

The LED light will automatically power oﬀ 10 seconds

after the switch is released.

ON/OFF

Lock button

Switch

trigger

LED light

Fig. 28

CAUTION

Do not look directly into the light from the LED

lamp. Continuous and direct exposure to the

light from the LED lamp can injure your eyes.

3. Adjusting the rotation speed

The M3612DA has an electronic control system

that allows rpm changes. As shown in Fig. 29, dial

position “1” is for minimum speed, and position “6” for

maximum speed.

Dial

Fig. 29

4. Cutting Operation

CAUTION

When processing the side of a material, make

sure that the side to be processed is on the left

of the bit in the direction that the material is fed.

Placing the side to be processed on the right of

the bit goes counter to the bit’s revolution and

may cause the motor to stop. Too much load in

such cases may result in malfunction.

19

English

NOTE

○

Do not press the lock pin while the motor is rotating.

Also, do not switch the tool on while pressing the lock

pin.

Doing so may damage the lock pin and/or shaft as

well as result in injury.

○

Please limit the cutting depth of a single cut to under

13/16" (20 mm).

○

When cutting a deep groove, repeat the cut 2 or 3

times.

Deep cutting operations can make the tool diﬃ cult

to control and may overload the motor, resulting in

malfunction.

○

Moving the tool forward fast may cause a poor quality

of cut, or damage to the bit or motor. Moving the tool

forward too slowly may burn and mar the cut.

The proper feed rate will depend on the bit size, the

kind of workpiece and depth of cut. Before beginning

the cut on the actual workpiece, it is advisable to

make a sample cut on a piece of scrap lumber. This

will show exactly how the cut will look as well as

enable you to check dimensions.

○

Abnormalities and overloads will trigger the overload

protector, and stop operation. Remove the load

immediately, and turn the power oﬀ , then on. The

rotation speed should return to normal.

(1) As shown in Fig. 30, remove the bit from the work

pieces and draw the switch trigger. Do not start

cutting operation until the bit has reached full rotating

speed.

Separate

Fig. 30

(2) The bit rotates clockwise (arrow direction indicated on

the base). To obtain maximum cutting eﬀ ectiveness,

feed the router in conformance with the feed directions

shown in Fig. 31.

Work piece

Rotation of bit

Router feed

Outer peripheral

cutting

(Counterclockwise)

Inner

peripheral

cutting

(Clockwise)

Fig. 31

5. LED light warning signals (Fig. 32)

This product features functions that are designed

to protect the tool itself as well as the battery. While

the switch is pulled, if any of the safeguard functions

activate during operation, the LED light will blink as

described in Table 5. When any of the safeguard

functions are triggered, immediately remove your

ﬁ nger from the switch and follow the instructions

described under corrective action.

Fig. 32

20

English

Table 5

Safeguard Function LED Light Display Corrective Action

Overload Protection On 0.1 second/oﬀ 0.1 second Remove the cause of the overloading.

Temperature Protection On 0.5 second/oﬀ 0.5 second Allow the tool and battery to thoroughly

cool.

6. About remaining battery indicator

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to light

the indicator lamp. (Fig. 33, Table 6)

The indicator will shut oﬀ approximately 3 seconds

after the remaining battery indicator switch is pressed.

It is best to use the remaining battery indicator as

a guide since there are slight diﬀ erences such as

ambient temperature and the condition of the battery.

Display panel

Remaining battery

indicator lamp Remaining battery

indicator switch

Fig. 33

Table 6

State of lamp Battery Remaining Power

Lights ;

The battery remaining power is over

75%.

Lights ;

The battery remaining power is

50%–75%.

Lights ;

The battery remaining power is

25%–50%.

Lights ;

The battery remaining power is less

than 25%.

Blinks ;

The battery remaining power is

nearly empty. Recharge the battery

soonest possible

Blinks ;

Output suspended due to high

temperature. Remove the battery

from the tool and allow it to fully cool

down.

Blinks ;

Output suspended due to failure or

malfunction. The problem may be

the battery so please contact your

dealer.

NOTE

○

Remaining battery levels may vary between that

shown on the battery and that of a product with its own

battery level function.

○

Do not give a strong shock to the display panel or

break it. It may lead to a trouble.

OPERATIONAL CAUTIONS

Resting the unit after continuous work

(1) The power tool is equipped with a temperature

protection circuit to protect the motor.

Continuous work may cause the temperature of the

unit to rise, activating the temperature protection

circuit and automatically stopping operation.

If this happens, allow the power tool to cool before

resuming use.

(2) After use for continuous work, rest the unit for

15 minutes or so when replacing the battery. The

temperature of the motor, switch, etc., will rise if

the work is started again immediately after battery

replacement, eventually resulting in burnout.

La page charge ...

Hikoki M3612DA Manuel utilisateur

Hikoki M3612DA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents