Hitachi CS 40EA Manuel utilisateur

Marque: Hitachi

Modèle: CS 40EA

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

CS40EA18

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand this

manual BEFORE operating the power tool. Please keep this manual available for other users and owners

before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de

sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de

lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi à la

disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi

doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede provocar lesiones

graves o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este

manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras

personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.

Model

Modèle

Modelo

CS 40EA

Chain Saw

Tronçonneuse

Motosierra

English

MEANINGS OF SYMBOLS

NOTE: Some units do not carry them.

Symbols

WARNING

The following show symbols used for the machine. Be sure that you understand their meaning before use.

It is important that you read, fully understand and observe the following safety precautions and warnings.

Careless or improper use of the unit may cause serious or fatal injury.

Read, understand and follow all warnings and instructions in this manual and on the unit.

Always wear eye, head and ear protectors when using this unit.

Warning, kickback danger. Be careful of possible sudden and accidental upward and/or backward motion

of the guide bar.

One-handed usage not permitted. While cutting, hold saw ﬁ rmly with both hands with thumb ﬁ rmly locked

around front handle.

Contents

WHAT IS WHAT? .............................................................................. 3

WARNINGS AND SAFETY INSTRUCTIONS .................................. 4

SPECIFICATIONS ............................................................................ 6

ASSEMBLY PROCEDURES ............................................................. 7

OPERATING PROCEDURES ........................................................... 7

MAI NT ENA NCE .............................................................................. 12

Parts breakdown

English

WHAT IS WHAT?

1. Throttle trigger: Device activated by the operatorʼs ﬁ nger, for

controlling the engine speed.

2. Throttle trigger lockout (Safety trigger): Device that prevents

the accidental operation of the throttle trigger until manually

released.

3. Ignition switch: Device for allowing the engine to be started or

stopped.

4. Oil tank cap: For closing the oil tank.

5. Recoil starter: Pull handle to start the engine.

6. Front handle: Support handle located at or towards the front of

the engine housing.

7. Fuel tank cap: For closing the fuel tank.

8. Choke control knob: Device for enriching the fuel/air mixture in

the carburetor, to aid starting.

9. Priming pump; Device for supplying extra fuel, to aid starting.

10. Guide bar: The part that supports and guides the saw chain.

11. Saw chain: Chain, serving as a cutting tool.

12. Chain brake (Front hand guard): Device for stopping or locking

the chain.

13. Spiked bumper : Device for acting as a pivot when in contact with

a tree or log.

14. Chain catcher: device for restraining the saw chain.

15. Guide bar cover: Device for covering the guide bar and saw

chain when the unit is not being used.

16. Combi box spanner: The tool for removing or installing a spark

plug and tensioning the saw chain.

17. Handling instructions: Included with unit. Read before operation

and keep for future reference to learn proper, safe techniques.

English

WARNINGS AND SAFETY INSTRUCTIONS

Operator safety

○ Always wear a safety face shield or goggles.

○ Gloves should be used when sharpening chain.

○ Always wear safety protective equipment such as jacket,

trousers, gloves, helmet, boots with steel toe-caps and non-slip

soles whenever you use a chain saw. For working in trees the

safety boots must be suitable for climbing techniques. Do not

wear loose clothing, jewelry, short pants, sandals or go barefoot.

Secure hair so it is above shoulder length.

○ Do not operate this tool when you are tired, ill or under the

inﬂ uence of alcohol, drugs or medication.

○ Never let a child or inexperienced person operate the machine.

○ Wear hearing protection. Pay attention to your surroundings.

Be aware of any bystanders who may be signaling a problem.

Remove safety equipment immediately upon shutting oﬀ engine.

○ Wear head protection.

○ Never start or run the engine inside a closed room or building.

Breathing exhaust fumes can kill.

○ For respiratory protection, wear a protection mask while emitting

the chain oil mist and dust from sawdust.

○ Keep handles free of oil and fuel.

○ Keep hands away from cutting equipment.

○ Do not grab or hold the unit by the cutting equipment.

○ When the unit turned oﬀ , make sure the cutting attachment has

stopped before the unit is set down.

○ When operation is prolonged, take a break from time to time

so that you may avoid possible Hand-Arm Vibration Syndrome

(HAVS) which is caused by vibration.

○ The operator must obey the local regulations of cutting area.

WARNING

○ Antivibration systems do not guarantee that you will not sustain

Hand-Arm Vibration Syndrome or carpal tunnel syndrome.

Therefore, continual end regular users should monitor closely

the condition of their hands and ﬁ ngers. If any of the above

symptoms appear, seek medical advice immediately.

○ Long or continuous exposure to high noise levels may cause

permanent hearing impairment. Always wear approved hearing

protection when operating a unit/machine.

○ If you are using any medical electric/electronic devices such

as a pacemaker, consult your physician as well as the device

manufacturer prior to operating any power equipment.

Unit/machine safety

○ Inspect the entire unit/machine before each use. Replace

damaged parts. Check for fuel leaks and make sure all fasteners

are in place and securely tightened.

○ Replace parts that are cracked, chipped or damaged in any way

before using the unit/machine.

○ Make sure the side case is properly attached.

○ Keep others away when making carburetor adjustments.

○ Use only accessories as recommended for this unit/machine by

the manufacturer.

○ Never let the chain strike any obstacle. If the chain makes

contact, the machine should be stopped and checked carefully.

○ Make sure the automatic oiler is working. Keep the oil tank ﬁ lled

with clean oil. Never let chain run dry on the bar.

○ All chain saw service, other than the items listed in the

operatorʼs/ ownerʼs manual, should be performed by competent

chain-saw service personnel. (For example, if improper tools are

used to remove the ﬂ ywheel or if an improper tool is used to hold

the ﬂ ywheel in order to remove the clutch, structural damage

to the ﬂ ywheel could occur and could subsequently cause the

ﬂ ywheel to burst.)

WARNING

○ Never modify the unit/machine in any way. Do not use your unit/

machine for any job except that for which it is intended.

○ Never use chain saw without any safety equipment or that has

faulty safety equipment. It could result in serious personal injury.

○ Using guide bar/chain other than recommended by the

manufacturer which are not approved, could result in a high risk

of personal accidents or injury.

Fuel safety

○ Mix and pour fuel outdoors and where there are no sparks or

ﬂ ames.

○ Use a container approved for fuel.

○ Do not smoke or allow smoking near fuel or the unit/machine or

while using the unit/machine.

○ Wipe up all fuel spills before starting engine.

○ Move at least 3 m away from fueling site before starting engine.

○ Stop engine before removing fuel cap.

○ Empty the fuel tank before storing the unit/machine. It is

recommended that the fuel be emptied after each use. If fuel is

left in the tank, store so fuel will not leak.

○ Store unit/machine and fuel in area where fuel vapors cannot

reach sparks or open ﬂ ames from water heaters, electric motors

or switches, furnaces, etc.

WARNING

Fuel is easy to ignite or get explosion or inhale fumes, so that pay

special attention when handling or ﬁ lling fuel.

Cutting safety

○ Do not cut any material other than wood or wooden objects.

○ For respiratory protection, wear an aerosol protection mask

when cutting the wood after insecticide has been applied.

○ Keep others including children, animals, bystanders and helpers

outside the hazard zone. Stop the engine immediately if you are

approached.

○ Hold the unit/machine ﬁ rmly with the right hand on the rear

handle and the left hand on the front handle.

○ Keep ﬁ rm footing and balance. Do not over-reach.

○ Keep all parts of your body away from the muﬄ er and cutting

attachment when the engine is running.

○ Keep Bar/Chain below waist level.

○ Before felling a tree, the operator must be accustomed to the

sawing techniques of the chain saw.

○ Be sure to pre-plan a safe exit from a failing tree.

○ While cutting, hold saw ﬁ rmly with both hands with thumb ﬁ rmly

locked around front handle, and stand with feet well balanced

and your body balanced.

○ Stand to the side of the saw when cutting - never directly behind

it.

○ Always keep the spiked bumper face to a tree, because the

chain may suddenly be drawn into a tree, if so equipped.

○ When completing a cut, be ready to hold up the units as it breaks

into clear, so it will not follow through and cut your legs, feet or

body, or contact an obstruction.

○ Be alert against kickback (when saw kicks up and back at

operator). Never cut with the nose of the bar.

○ When relocating to a new work area, be sure to shut oﬀ the

machine and ensure that all cutting attachments are stopped.

○ Never place the machine on the ground when running.

○ Always ensure that the engine is shut oﬀ and any cutting

attachments have completely stopped before clearing debris or

removing grass from the cutting attachment.

○ Always carry a ﬁ rst-aid kit when operating any power equipment.

○ Never start or run the engine inside a closed room or building

and/or near the inﬂ ammable liquid. Breathing exhaust fumes

can kill.

Maintenance safety

○ Maintain the unit/machine according to recommended

procedures.

○ Disconnect the spark plug before performing maintenance

except for carburetor adjustments.

○ Keep others away when making carburetor adjustments.

○ Use only genuine HITACHI replacement parts as recommended

by the manufacturer.

CAUTION

Do not disassemble the recoil starter. You may get a possibility

of personal injury with recoil spring.

English

WARNING

Improper maintenance could result in serious engine damage or

in serious personal injury.

Transpor t and storage

○ Carry the unit/machine by hand with the engine stopped and the

muﬄ er away from your body.

○ Allow the engine to cool, empty the fuel tank, and secure the

unit/machine before storing or transporting in a vehicle.

○ Empty the fuel tank before storing the unit/machine. It is

recommended that the fuel be emptied after each use. If fuel is

left in the tank, store so fuel will not leak.

○ Store unit/machine out of the reach of children.

○ Clean and maintain the unit carefully and store it in a dry place.

○ Make sure engine switch is oﬀ when transporting or storing.

○ When transporting or storage, cover chain with chain cover.

If situations occur which are not covered in this manual, take care and

use common sense. Contact HITACHI dealer if you need assistance.

Pay special attention to statements preceded by the following words:

WARNING

Indicates a strong possibility of severe personal injury or loss of

life, if instructions are not followed.

CAUTION

Indicates a possibility of personal injury or equipment damage, if

instructions are not followed.

NOTE

Helpful information for correct function and use.

English

SPECIFICATIONS

○ Code CS of model name means Chain saw

Model CS40EA (45PS)

Type of equipment Chain saw, portable

Engine Size (cu. in.) 2.41 (39.6 ml)

Spark Plug NGK BPM-7A or BPMR-7A or equivalent

Fuel Tank Capacity (US pint) 0.80 (380 ml)

Chain Oil Tank Capacity (US pint) 0.51 (240 ml)

Dry Weight (lbs)

(Without guide bar and chain)

9.9 (4.5 kg)

Guide bar length (in.) 18 (450 mm)

Chain pitch (in.) 0.325 (8.26 mm)

Chain gauge (in.) 0.05 (1.27 mm)

Sound pressure level

LpA (dB (A))

by ISO 22868

103

Sound power level

Lw measured (dB (A))

by ISO 22868

Sound power level LwA (dB (A))

by 2000/14/EC

113

114

Vibration level (m/s

)

by ISO 22867

Front handle

Rear handle

2.2

3.2

Max. engine power

by ISO 7293 (kW)

1.8/10500

Max. engine speed (min

-1

) 13000

Idle engine speed (min

-1

) 3000

Speciﬁ c fuel consumption (g/kWh) 480

Type of chain

95VP

(Oregon)

Max. chain speed (m/sec) 23.1

Sprocket (number of teeth) 7

NOTE: Equivalent noise level/vibration levels are calculated as the time-weighted energy total for noise/vibration levels under various working

conditions with the following time distribution: 1/3 idle, 1/3 full, 1/3 racing speed.

* All data subject to change without notice.

Declared single-number noise emission values are the sum of measure values and the associated uncertainty of 3dB and they represent

upper boundaries of the range of values which is likely to occur in measurements.

English

5. Guide the chain drive links into the bar groove all around the bar.

6. Install the side case (2) onto the bolts (5).

Then tighten the clamp nuts (1) temporarily.

(

Fig. 1

)

7. Raise the bar end, and tighten the chain (9) by turning the tension

adjustment bolt (10) clockwise. To check proper tension, lightly

lift up the center of chain and there should be about 0.5 – 1.0 mm

clearance between bar and edge of drive link (11). (Fig. 5, 6)

Fig. 5

Fig. 6

CAUTION

PROPER TENSION IS EXTREMELY IMPORTANT

8. Raise the bar end and securely tighten the chain bar clamp nuts

with the combi box spanner. (Fig. 6)

9. A new chain will stretch so adjust the chain after a few cuts and

watch chain tension carefully for the ﬁ rst half hour of cutting.

NOTE

Check the chain tension frequently for optimum performance

and durability.

CAUTION

○ When the chain is excessively tightened, the bar and chain will

be damaged rapidly. Conversely, when the chain is excessively

loosened, it may get out of the groove in the bar.

○ Always wear gloves when touching the chain.

WARNING

During operation, hold chain saw ﬁ rmly with both hands. A single

hand operation may cause serious injury.

OPERATING PROCEDURES

Fuel (Fig. 7)

Fig. 7

ASSEMBLY PROCEDURES

WARNING

Never try to start engine without side case securely fastened.

1. Remove chain bar clamp nuts (1).

2. Remove the side case (2) as pinching the rear part of the side

case (2). (Fig. 1)

Fig. 1

* In case of installing the spiked bumper (3), install the spiked

bumper (3) to the unit with two screws. (Fig. 2)

Fig. 2

3. Install the chain bar (4) onto the bolts (5), then push it toward the

sprocket (6) as far as it will go. Make sure that the boss of chain

tension adjust bolt (7) ﬁ ts into the hole of the bar (8). (Fig. 3)

78 5

Fig. 3

NOTE

Slightly move the bar back and forth and make sure the chain

tension boss (7) ﬁ ts into the hole (8) in the bar properly. (Fig. 3)

4. Conﬁ rm the direction of saw chain (9) is correct as in the ﬁ gure,

and align the chain on the sprocket. (Fig. 4)

Fig. 4

0.5

1.0 mm

English

WARNING

○ The chain saw is equipped with a two-stroke engine. Always

run the engine on fuel, which is mixed with oil. Provide good

ventilation, when fueling or handling fuel.

○ Fuel contains highly ﬂ ammable and it is possible to get the

serious personal injury when inhaling or spilling on your body.

Always pay attention when handling fuel. Always have good

ventilation when handling fuel inside building.

Fuel

○ Always use branded 89 octane unleaded gasoline.

○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1,

please consult the oil bottle for the ratio or HITACHI dealer.

○ Only for the state of California at 50:1.

○ If genuine oil is not available, use an anti-oxidant added quality

oil expressly labeled for air-cooled 2-cycle engine use (JASO

FC GRADE OIL or ISO EGC GRADE). Do not use BIA or TCW

(2-stroke water-cooling type) mixed oil.

○ Never use multi-grade oil (10 W/30) or waste oil.

○ Always mix fuel and oil in a separate clean container.

Always start by ﬁ lling half the amount of gasoline, which is to be

used.

Then add the whole amount of oil. Mix (shake) the fuel mixture. Add

the remaining amount of gasoline.

Mix (shake) the fuel-mix thoroughly before ﬁ lling the fuel tank.

Fueling

WARNING (Fig. 8)

○ Always shut oﬀ the engine before refueling.

○ Slowly open the fuel tank (12), when ﬁ lling up with fuel, so that

possible overpressure disappears.

○ Tighten the fuel cap carefully, after fueling.

○ Always move the unit at least 3 m from the fueling area before

starting.

○ Always wash any spilled fuel from clothing immediately with

soap.

○ Be sure to check any fuel leaking after refueling.

Fig. 8

Before fueling, clean the tank cap area carefully, to ensure that no

dirt falls into the tank. Make sure that the fuel is well mixed by shaking

the container, before fueling.

Chain oil (Fig. 8)

Fill up with chain oil (13). Always use good quality chain oil. When the

engine is running, the chain oil is automatically discharged.

NOTE

When pouring fuel (12) or chain oil (13) into the tank, place the

unit with cap side up. (Fig. 8)

ADJUSTMENT OF CHAIN OIL SUPPLY

The chain oil quantity discharged through the lubrication system is

factory adjusted to the maximum. Adjust the quantity in accordance

with the operating condition.

Turn the adjusting screw (14) counterclockwise to increase the

quantity and turn it clockwise to decrease the quantity. (Fig. 9)

(standard setting turns counterclockwise 1-1 1/2 from slightly seated)

Fig. 9

Starting (Fig. 10

15)

CAUTION

Before starting, make sure chain brake is engaged and that the

bar/chain does not touch anything. (Fig. 10)

Fig. 10

1. Set ignition switch (15) to ON position. (Fig. 11)

Fig. 11

*Push priming bulb (17) several times so that fuel ﬂ ows through

bulb into carburetor. (Fig. 12)

Fig. 12

2. Pull the choke lever (16) to choked position (Fig. 12). This will

automatically lock the throttle in starting position.

English

3. Pull recoil starter briskly, taking care to keep the handle in your

grasp and not allowing it to snap back. (Fig. 13)

Fig. 13

4. When you hear ﬁ rst ignition, return the choke to run position.

(Fig. 12)

5. Pull recoil starter briskly again in the aforementioned manner.

(Fig. 13)

NOTE

If engine does not start, repeat procedures from 2 to 5.

6. As soon as engine start, pull throttle lever full once and release

immediately. (Fig. 14)

Then half-throttle is disengaged. Make sure chain brake is

disengaged. (Fig. 15)

Allow the engine about 2-3 minutes to warm up before subjecting

it to any load.

Do not run the engine at high speed without the load to shorten

the longevity of the engine.

Fig. 14

Fig. 15

Chain brake operation (Fig. 16)

Fig. 16

Chain brake (18), if so equipped, is designed to activate in an

emergency such as kick-back action. Please check to verify that it

works properly before use.

Application of brake is made by moving the front guard towards the

bar. During the chain brake operation, even if the throttle lever is

pulled, the engine speed does not increase and the chain does not

turn. To release the brake, pull up the chain brake lever.

How to conﬁ rm:

1) Turn oﬀ the engine.

2) Holding the chain saw horizontally, release your hand from the

front handle, hit the tip of the guide bar to a stump or a piece

of wood, and conﬁ rm brake operation. Operating level varies by

bar size.

In case the brake is not eﬀ ective, ask our dealer for inspection and

repairs. If the engine keeps rotating at high speed with the brake

engaged, the clutch will overheat causing trouble.

When the brake engages during operation, immediately release the

throttle lever to stop the engine.

WARNING

Do not carry the machine with the engine running.

Stopping (Fig. 17)

Fig. 17

Decrease engine speed, and push ignition switch (15) to stop

position.

WARNING

KICKBACK DANGER (Fig. 18)

Fig. 18

One of the most severe dangers when working with a chain saw is

the possibility of kickback. Kickback may occur when the upper tip

of the guide bar touches an object, or when the wood closes in and

pinches the saw chain in the cut. Tip contact in some cases may

cause a lightning fast reverse reaction, kicking the guide bar up and

back toward you. Pinching the saw chain along the top of the guide

bar may also push the guide bar rapidly back towards you. Either of

these reactions may cause you to lose control of the saw which could

result in serious personal injury. Even though your saw has safety

built into its design, you should not rely on these safety features

exclusively. Know where your bar tip is at all times. Kickback does

occur if you allow the kickback zone (19) of the bar to touch an object.

English

Do not use that area. Kickback from pinching is caused by a cut

closing and pinching the upper side of the guide bar. Study your cut

and make sure it will open as you cut through. Maintain control when

the engine is running by always keeping a ﬁ rm grip on the saw with

your right hand on the rear handle, your left hand on the front handle

and your thumbs and ﬁ ngers encircling the handles. Always hold the

saw with both hands during operation and cut at high engine speed.

WARNING

○ Do not overreach or cut above shoulder height.

○ Use extra caution when felling, and do not use the saw in a nose-

high position or above shoulder height.

CHAIN CATCHER

The chain catcher is located on the power head just below the chain

to further prevent the possibility of a broken chain striking the chain

saw user.

WARNING

Do not stand in-line with chain when cutting.

BASIC TECHNIQUES FOR MAKING FELLING, LIMBING AND

BUCKING CUTS

The intention of the following information is to provide you with the

general introduction to wood cutting techniques.

WARNING

○ This information does not cover all speciﬁ c situations, which

may depend on diﬀ erences in terrain, vegetation, kind of wood,

form and size of trees, etc. Consult your servicing dealer,

forestry agent or local forestry schools for advice on speciﬁ c

woodcutting problems in your area. This will make your work

more eﬃ cient and safer.

○ Avoid cutting in adverse weather conditions, such as dense fog,

heavy rain, bitter cold, high winds, etc.

Adverse weather is often tiring to work in and creates potentially

dangerous conditions such as slippery ground.

High winds may force the tree to fall in an unexpected direction

causing property damage or personal injury.

CAUTION

Never use a chain saw to pry or for any purpose for which it is not

intended.

WARNING

○ Avoid stumbling on obstacles such as stumps, roots, rocks,

branches and fallen trees. Watch out for holes and ditches. Be

extremely cautious when working on slopes or uneven ground.

Shut oﬀ the saw when moving from one work place to another.

Always cut at wide open throttle. A slow moving chain can easily

catch and force the saw to jerk.

○ Never use the saw with only one hand.

You cannot control the saw properly and you may lose control

and injure yourself severely.

Keep the saw body close to your body to improve control and

reduce strain.

When cutting with the bottom part of the chain the reactive force

will pull the saw away from you towards the wood you are cutting.

The saw will control the feeding speed and sawdust will be

directed towards you. (Fig. 19)

Fig. 19

○ When cutting with the upper part of the chain the reactive force

will push the saw towards you and away from the wood you are

cutting. (Fig. 20)

Fig. 20

○ There is a risk of kickback if the saw is pushed far enough so that

you begin to cut with the nose of the bar.

The safest cutting method is to cut with the bottom part of the

chain. Sawing with the upper part makes it much more diﬃ cult to

control the saw and increases the risk of kickback.

○ In case the chain locked, immediately release the throttle lever.

If the throttle lever keeps rotating at high speed with the chain

locked, the clutch will overheat causing trouble.

NOTE

Always keep the spiked bumper face to a tree, because the

chain may suddenly be drawn into a tree.

FELLING

Felling is more than cutting down a tree. You must also bring it down

as near to an intended place as possible without damaging the tree

or anything else.

Before felling a tree, carefully consider all conditions which may

eﬀ ect the intended direction, such as:

Angle of the tree. Shape of the crown. Snow load on the crown.

Wind conditions. Obstacles within tree range (e.g., other trees,

power lines, roads, buildings, etc.).

WARNING

○ Always observe the general conditions of the tree. Look for

decay and rot in the trunk which will make it more likely to snap

and start to fall before you expect it.

○ Look for dry branches, which may break and hit you when you

are working.

Always keep animals and people at least twice the tree length

away while felling. Clear away shrubs and branches from around

the tree.

Prepare a path of retreat away from the felling direction.

BASIC RULES FOR FELLING TREES

Normally the felling consists of two main cutting operations, notching

and making the felling cut. Start making the upper notch cut on the

side of the tree facing the feeling direction. Look through the kerf as

you saw the lower cut so you do not saw too deep into the trunk. The

notch should be deep enough to create a hinge of suﬃ cient width

and strength. The notch opening should be wide enough to direct

the fall of the tree as long as possible. Saw the felling cut from the

other side of the tree between one and two inches (3–5 cm) above

the edge of the notch. (Fig. 21)

Fig. 21

English

20. Felling direction

21. 45° minimum notch opening

22. Hinge

23. Felling cut

Never saw completely through the trunk. Always leave a hinge.

The hinge guides the tree. If the trunk is completely cut through, you

lose control over the felling direction.

Insert a wedge or a felling lever in the cut well before the tree

becomes unstable and starts to move. This will prevent the guide

bar from binding in the felling cut if you have misjudged the falling

direction. Make sure no people have come into the range of the

falling tree before you push it over.

FELLING CUT, TRUNK DIAMETER MORE THAN TWICE GUIDE

BAR LENGTH

Cut a large, wide notch. Then cut a recess into the center of the

notch. Always leave a hinge on both sides of the center cut. (Fig. 22)

Fig. 22

Complete the felling cut by sawing around the trunk as in the Fig. 23.

Fig. 23

WARNING

These methods are extremely dangerous because they involve

the use of the nose of guide bar and can result in kickback.

Only properly trained professionals should attempt these

techniques.

LIMBING

Limbing is removing the branches from a feller tree.

WARNING

A majority of kickback accidents occur during Iimbing.

Do not use the nose of the guide bar. Be extremely cautious and

avoid contacting the log, other limbs or objects with the nose

of the guide bar. Be extremely cautious of limbs under tension.

They can spring back towards you and cause loss of control

resulting in injury. (Fig. 24)

Fig. 24

Stand on the left side of the trunk. Maintain a secure footing and

rest the saw on the trunk. Hold the saw close to you so that you are

in full control of it. Keep well away from the chain. Move only when

the trunk is between you and the chain. Watch out for spring back of

limbs under tension.

LIMBING THICK BRANCHES

When limbing thick branches, the guide bar may get pinched easily.

Branches under tension often snap up, so cut troublesome branches

in small steps. Apply the same principles as for cross cutting. Think

ahead and be aware of the possible consequences of all your

actions.

CROSS CUTTING/BUCKING

Before starting to cut through the log, try to imagine what is going to

happen. Look out for stresses in the log and cut through it in such a

manner that the guide bar will not get pinched.

CROSS CUTTING LOGS, PRESSURE ON TOP

Take a ﬁ rm stance. Begin with an upper cut. Do not cut too deeply,

about 1/3 of the log diameter is enough. Finish with a bottom cut.

The saw cuts should meet. (Fig. 25)

Fig. 25

24. Relieving cut

25. Cross cut

26. Pressure on top

27. Pressure side

28. Tension side

29. Relative depth of saw cuts

THICK LOG, LARGER THAN GUIDE BAR LENGTH

Begin by cutting on the opposite side of the log. Pull the saw towards

you, followed by previous procedure. (Fig. 26)

Fig. 26

If the log is lying on the ground make a boring cut to avoid cutting into

the ground. Finish with a bottom cut. (Fig. 27)

Fig. 27

English

WARNING

KICKBACK DANGER

Do not attempt a boring cut if you are not properly trained. A

boring cut involves the use of the nose of the guide bar and can

result in kickback.

CROSS CUTTING LOGS, PRESSURE ON BOTTOM

Take a ﬁ rm stance. Begin with a bottom cut. The depth of the cut

should be about 1/3 of the log diameter.

Finish with an upper cut. The saw cuts should meet. (Fig. 28)

Fig. 28

30. Relieving cut

31. Cross cut

32. Pressure on bottom

33. Tension side

34. Pressure side

35. Relative depth of saw cuts

THICK LOG, LARGER THAN GUIDE BAR LENGTH

Begin by cutting on the opposite side of the log. Pull the saw towards

you, followed by previous procedure. Make a boring cut if the log is

close to the ground. Finish with a top cut. (Fig. 29)

Fig. 29

WARNING

KICKBACK DANGER

Do not attempt a boring cut if you are not properly trained. A

boring cut involves the use of the nose of the guide bar and can

result in kickback. (Fig. 30)

Fig. 30

IF THE SAW GETS STUCK

Stop the engine. Raise the log or change its position, using a thick

branch or pole as a lever. Do not try to pull the saw free. If you do,

you can deform the handle or be injured by the saw chain if the saw

is suddenly released.

MAINTENANCE

MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION

CONTROL DEVICES AND SYSTEM MAY BE PERFORMED BY ANY

NON-ROAD ENGINE REPAIR ESTABLISHMENT OR INDIVIDUAL.

Carburetor adjustment (Fig. 31)

Fig. 31

WARNING

Never start the engine without the complete clutch cover.

Otherwise the clutch can come loose and cause personal injuries.

In the carburetor, fuel is mixed with air. When the engine is test run at

the factory, the carburetor is adjusted. A further adjustment may be

required, according to climate and altitude. The carburetor has one

adjustment possibility:

T = Idle speed adjustment screw.

Idle speed adjustment (T)

Check that the air ﬁ lter is clean. When the idle speed is correct, the

cutting attachment will not rotate. If adjustment is required, close

(clockwise) the T-screw, with the engine running, until the cutting

attachment starts to rotate. Open (counter-clockwise) the screw

until the cutting attachment stops. You have reached the correct idle

speed when the engine runs smoothly in all positions well below the

rpm when the cutting attachment starts to rotate.

If the cutting attachment still rotates after idle speed adjustment,

contact HITACHI dealer.

WARNING

When the engine is idling the cutting attachment must under no

circumstances rotate.

NOTE

Some models sold in areas with strict exhaust emission

regulation do not have high and low speed carburetor

adjustments. Such adjustments may allow the engine to be

operated outside of their emission compliance limits. For these

models, the only carburetor adjustment is idle speed.

If you are not familiar with this type of adjustment, please ask for

assistance from your HITACHI dealer.

Air ﬁ lter (Fig. 32)

The air ﬁ lter (36) must be cleaned from dust and dirt in order to avoid:

○ Carburetor malfunctions.

○ Starting problems.

○ Engine power reduction.

○ Unnecessary wear on the engine parts.

○ Abnormal fuel consumption.

Clean the air ﬁ lter daily or more often if working in exceptionally

dusty areas.

Cleaning the air ﬁ lter

Remove the air ﬁ lter cover (37) and the ﬁ lter (36).

Rinse them in warm soap suds. Check that the ﬁ lter is dry before

reassembly. An air ﬁ lter that has been used for some time cannot be

cleaned completely. Therefore, it must regularly be replaced with a

new one. A damaged ﬁ lter must always be replaced.

English

Fig. 35

Side case (Fig. 36)

Always keep the side case and drive area clean of saw dust and

debris. Periodically apply oil or grease to this area to protect from

corrosion as some trees contain high levels of acid.

Fig. 36

Fuel ﬁ lter (Fig. 37)

Remove the fuel ﬁ lter from the fuel tank and thoroughly wash it in

solvent. After that, push the ﬁ lter into the tank completely.

Fig. 37

NOTE

If the ﬁ lter is hard due to dust and dirt, replace it.

Chain oil ﬁ lter (Fig. 38)

Remove the oil ﬁ lter and thoroughly wash it in solvent.

Fig. 38

Fig. 32

Spark plug (Fig. 33)

The spark plug condition is inﬂ uenced by:

○ An incorrect carburetor setting.

○ Wrong fuel mixture (too much oil in the gasoline)

○ A dirty air ﬁ lter.

○ Hard running conditions (such as cold weather).

These factors cause deposits on the spark plug electrodes, which

may result in malfunction and starting diﬃ culties. If the engine is low

on power, diﬃ cult to start or runs poorly at idling speed, always check

the spark plug ﬁ rst. If the spark plug is dirty, clean it and check the

electrode gap. Readjust if necessary. The correct gap is 0.024” (0.6

mm). The spark plug should be replaced after about 100 operation

hours or earlier if the electrodes are badly eroded.

0.6 mm

Fig. 33

NOTE

In some areas, local law requires using a resistor spark plug

to suppress ignition signals. If this machine was originally

equipped with resistor spark plug, use same type of spark plug

for replacement.

Oiler port (Fig. 34)

Clean the chain oiler port (38) whenever possible.

Fig. 34

Guide bar (Fig. 35)

Before using the machine, clean the groove and oiler port (39) in the

bar with the special gauge oﬀ ered as an optional accessory.

0.024"(0.6 mm)

English

Cleaning the cylinder ﬁ ns (Fig. 39)

When wood chips are caught between cylinder ﬁ ns (40), the engine

may overheat, resulting in lower output. To avoid this, always keep

cylinder ﬁ ns and fan case clean.

Every 100 operating hours, or once a year (more often if conditions

require), clean ﬁ ns and external surfaces of engine of dust, dirt and

oil deposits which can contribute to improper cooling.

Fig. 39

Cleaning the muﬄ er (Fig. 40)

Remove the muﬄ er and spark arrestor, if so equipped, and clean out

any excess carbon from the exhaust port or muﬄ er inlet every 100

hours of operation.

Fig. 40

For long-term storage

Drain all fuel from the fuel tank. Start and let engine run until it stops.

Repair any damage which has resulted from use. Clean the unit with

a clean rag, or the use of high pressure air hose. Put a few drops of

two-cycle engine oil into the cylinder through the spark plug hole,

and spin the engine over several times to distribute oil.

Cover the unit and store it in a dry area.

CHAIN SHARPENING

Parts of a cutter (Fig. 41, 42)

Fig. 41

Fig. 42

WARNING

○ Gloves should be used when sharpening chain.

○ Be sure to round oﬀ the front edge to reduce the chance of

kickback or tie-strap breakage.

41. Top plate

42. Working corner

43. Side plate

44. Gullet

45. Heel

46. Chassis

47. Rivet hole

48. Toe

49. Depth gauge

50. Correct angle on top plate (degree of angle depends on chain

type)

51. Slightly protruding “hook” or point (curve on non-chisel chain)

52. Top of depth gauge at correct height below top plate

53. Front of depth gauge rounded oﬀ

LOWERING DEPTH GAUGES WITH A FILE

1) If you sharpen your cutters with a ﬁ le holder, check and lower the

depth.

2) Check depth gauges every third sharpening.

3) Place depth gauge tool on cutter. If depth gauge projects, ﬁ le

it level with the top of the tool. Always ﬁ le from the inside of the

chain toward an outside cutter. (Fig. 43)

Fig. 43

4) Round oﬀ front corner to maintain original shape of depth gauge

after using depth gauge tool. Always follow the recommended

depth gauge setting found in the maintenance or operator

manual for your saw. (Fig. 44)

Fig. 44

English

GENERAL INSTRUCTIONS FOR FILING CUTTERS

File (54) cutter on one side of the chain from the inside out. File on

forward stroke only. (Fig. 45)

5454

Fig. 45

5) Keep all cutters the same length. (Fig. 46)

Fig. 46

6) File enough to remove any damage to cutting edges (side plate

(55) and top plate (56)) of cutter. (Fig. 47)

Fig. 47

SHARPENING ANGLES FOR SHARPENING SAW CHAIN

1. Part Number 95VP

2. Pitch .325”

3. Depth Gauge Setting 0.025"

4. Side Plate Filing Angle 85°

5. Top Plate Angle 30°

6. File Guide Angle 10°

Maintenance schedule

Below you will ﬁ nd some general maintenance instructions. For

further information please contact HITACHI dealer.

Daily maintenance

○ Clean the exterior of the unit.

○ Clean the chain oil ﬁ lter port.

○ Clean the groove and oil ﬁ lter port in the guide bar.

○ Clean the side case of saw dust.

○ Check that the saw chain is sharp.

○ Check that the bar nuts are suﬃ ciently tightened.

○ Make sure that the chain transport guard is undamaged and that

it can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently tightened.

Especially inspect the bolt of muﬄ er and ensure that they are

properly tightened before starting engine. Should any of the

bolts be loose, retighten them immediately. Failure to do so

could result in serious hazard.

○ Check the tip of the bar. Please exchange it for the new one

when it is worn out.

○ Check the band of chain brake. Please exchange it for the new

one when it is worn out.

Weekly maintenance

○ Check the starter, especially cord and return spring.

○ Clean the exterior of the spark plug.

○ Remove the spark plug and check the electrode gap. Adjust it to

0.024” (0.6 mm) or change the spark plug.

○ Clean the cooling ﬁ ns on the cylinder and check that the air

intake at the starter is not clogged.

○ Clean the air ﬁ lter.

Monthly maintenance

○ Rinse the fuel tank with gasoline, and clean fuel ﬁ lter.

○ Clean chain oil ﬁ lter.

○ Clean the exterior of the carburetor and the space around it.

○ Clean the fan and the space around it.

○ Clean the muﬄ er of carbon.

NOTE

When ordering the parts to your nearest dealer, please use the

item numbers showing on the parts breakdown section in this

instruction.

BAR NO.

LENGTH-

TYPE

CHAIN NO.

MODEL NO.

OREGON

107498

105191

104968

105355

13”

15”

16”

18”

95VP-56

95VP-64

95VP-66

95VP-72

Français

SIGNIFICATION DES SYMBOLES

REMARQUE : Certains appareils n’en sont pas pourvus.

Symboles

ATTENTION

Les symboles suivants sont utilisés pour l’outil. Bien se familiariser avec leur signiﬁ cation avant d’utiliser

l’outil.

Il est essentiel que vous lisiez et compreniez parfaitement les consignes de sécurité et autres

avertissements suivants et que vous les observiez strictement. L’utilisation inattentive ou inadéquate de

cette machine risque de provoquer des blessures graves ou fatales.

Lisez, comprenez et suivez toutes les instructions et tous les avertissements donnés dans ce manuel et

sur le produit.

Utilisez toujours des lunettes de protection ainsi qu’une protection pour la tête et les oreilles lorsque vous

utilisez ce produit.

Portez une attention particulière aux phénomènes de rebond. Prenez garde aux mouvements possibles

soudains et accidentels du guide-chaîne de votre tronçonneuse.

L’utilisation d’une tronçonneuse avec une seule main n’est pas autorisée. Lorsque vous coupez avec

votre machine, tenir celle-ci fermement avec les deux mains, le pouce enserrant la poignée avant.

Sommaire

DESCRIPTION................................................................................ 17

PRÉCAUTIONS ET CONSIGNES DE SÉCURITÉ ......................... 18

SPÉCIFICATIONS .......................................................................... 20

MONTAGE 21

UTILISATION .................................................................................. 22

ENT RET IEN .................................................................................... 27

Liste des pièces détachées

Français

DESCRIPTION

1. Commande des gaz : Dispositif actionné par le doigt de

l’opérateur pour la commande de vitesse du moteur.

2. Levier accélérateur bloqué : Dispositif qui empêche le

déclenchement accidentel de la commande des gaz tant qu’elle

n’est pas relâchée manuellement.

3. Commutateur de marche/arrêt : Dispositif permettant de lancer

ou d’arrêter le moteur.

4. Bouchon du réservoir d’huile : Permet de fermer le réservoir

d’huile.

5. Lanceur à retour automatique : Tirer sur la poignée pour lancer

le moteur.

6. Poignée avant : Poignée de soutien située sur ou vers l’avant du

carter moteur.

7. Bouchon du réservoir de carburant : Permet de fermer le

réservoir de carburant.

8. Bouton de commande du starter : Dispositif qui enrichit le

mélange essence/air dans le carburateur pour faciliter le

démarrage.

9. Bomba de escorvar ; Dispositivo para fornecer combustível

adicional, para ajudar no arranque.

10. Guide-chaîne : Pièce qui soutient et guide la chaîne de coupe.

11. Chaîne découpe : Chaîne qui sert d’instrument découpe.

12. Frein de chaîne (protection de main avant) : Dispositif d’arrêt ou

de verrouillage de la chaîne.

13. Griﬀ e d’abattage : Dispositif qui tient lieu de pivot quand l’outil

entre en contact avec un arbre ou un billot de bois.

14. Capteur de chaîne : Dispositif qui retient la chaîne de coupe.

15. Cache de guide-chaîne : Dispositif qui recouvre le guide-chaîne

et la chaîne de coupe quand on ne se sert pas de l’outil.

16. Clé à douille multiple : Outil qui permet de déposer et de

remonter la bougie et de tendre la chaîne de coupe.

17. Mode d’emploi : Fourni avec l’outil. Lisez-le avant d’utiliser

l’outil et conservez-le à des ﬁ ns de référence ultérieure pour

apprendre les techniques d’utilisation correcte et de sécurité.

Français

PRÉCAUTIONS ET CONSIGNES DE SÉCURITÉ

Sécurité de l’utilisateur

○ Portez toujours une visière et des lunettes de protection.

○ Vous devez toujours porter des gants de protection lorsque vous

aﬀ ûtez la chaîne.

○ Portez toujours un équipement de protection tel qu’un veston,

un pantalon, des gants, un casque, des bottes avec les orteil-

casquettes d’acier et des semelles antidérapantes quand vous

utilisez la tronçonneuse. Pour travailler dans les arbres, utilisez

des bottes les bottes spécialisées pour l’escalade. Ne portez

pas de vêtements amples, de shorts, de sandales et ne vous

promenez pas pieds nus.

Veillez à attacher vos cheveux s’ils sont longs.

○ N’utilisez cet outil que si vous êtes en pleine possession de vos

moyens physiques (qui vous n’êtes pas fatigué, malade ou sous

l’inﬂ uence d’un alcool, d’une drogue ou de médicaments).

○ Ne jamais laisser un enfant ou une personne inexpérimentée se

servir de cet outil.

○ Portez un dispositif de protection contre le bruit pour vos

oreilles. Restez vigilant à tout ce qui vous entoure.

Restez attentif dans l’éventualité où une personne située à

proximité vous signalerait un problème.

Retirez les équipements de sécurité immédiatement après avoir

coupé le moteur de l’appareil.

○ Protégez-vous la tête.

○ Ne démarrez jamais le moteur de l’appareil dans un local clos ou

à l’intérieur d’un bâtiment.

L’inhalation des fumées d’échappement peut être mortelle.

○ Pour la protection respiratoire, porter un masque quand un

nuage d’huile de la chaîne et de la poussière est émise de la

sciure.

○ Nettoyez les poignées de toute trace d’huile ou de carburant.

○ N’approchez jamais les mains du guide-chaîne et de la chaîne.

○ N’attrapez jamais, ni ne tenez la machine par l’extrémité du

guide-chaîne.

○ Après l’arrêt de la tronçonneuse, attendez l’arrêt complet de la

chaîne de coupe avant de poser la machine.

○ Lors d’une utilisation prolongée, veillez à faire une pause

périodiquement, aﬁ n d’éviter le Syndrome des vibrations mains/

bras (HAVS) provoqués par les vibrations.

○ L’utilisateur de la machine doit se conformer aux réglementations

locales de la région dans laquelle il eﬀ ectue la coupe.

ATTENTION

○ Les systèmes anti-vibrations, aussi bon soient-ils, ne vous

protègent pas complément du syndrome des vibrations mains/

bras (HAVS), ni du syndrome du canal carpien.

Par conséquent, si vous vous servez de façon régulière et

continue de votre tronçonneuse, surveillez soigneusement l’état

de vos mains et de vos doigts. Si l’un des symptômes ci-dessus

venait à apparaître, faites vous examiner immédiatement par

votre médecin.

○ Une exposition longue ou continue à des bruits de niveau élevé

peut causer les troubles d’audition permanents. Portez toujours

un équipement de protection d’oreilles lors de l’utilisation de

l’outils.

○ Si vous êtes équipé d’un appareillage médical électrique/

électronique tel qu’un stimulateur cardiaque, consultez votre

médecin et le fabricant de cet appareillage avant d’utiliser tout

appareil électrique.

Règles de sécurité concernant l’utilisation de la machine.

○ Contrôlez entièrement votre machine avant chaque utilisation.

Remplacez les pièces endommagées. Vériﬁ ez l’absence de

fuites de carburant et assurez-vous que tous les dispositifs de

ﬁ xation sont en place et solidement ﬁ xés.

○ Remplacez les éléments de la machine qui présentent des

ﬁ ssures, des ébréchures ou toute autre avarie.

○ Assurez-vous que le capot latéral est correctement installé.

○ Ne laissez personne s’approcher lorsque vous réglez le

carburateur.

○ Utilisez uniquement les accessoires recommandés par le

constructeur pour cette machine.

○ Ne laissez jamais la chaîne frapper contre un obstacle

quelconque. Si la chaîne rencontre un obstacle, il est nécessaire

d’arrêter le fonctionnement de la machine et de l’inspecter

soigneusement pour voir si elle n’est pas endommagée.

○ Assurez-vous que le système de graissage automatique

fonctionne normalement. Le réservoir d’huile doit toujours être

suﬃ samment rempli d’huile propre. Ne jamais laisser la chaîne

tourner à sec sur le guide-chaîne.

○ Tous les travaux d’entretien de la tronçonneuse, en dehors de

ceux indiqués dans le manuel d’entretien de l’utilisateur doivent

être eﬀ ectués par un personnel qualiﬁ é pour l’entretien des

tronçonneuses. (Par exemple, des outils incorrects sont utilisés

pour extraire le volant, ou si un outil incorrect est utilisé pour

maintenir le volant avant la dépose de l’embrayage, cela peut

entraîner des dommages structurels au volant et peut ensuite

provoquer sont éclatement.)

ATTENTION

○ Ne modiﬁ ez en aucun cas la machine. N’utilisez jamais la

tronçonneuse pour tout autre tâche que celles auxquelles elle

est destinée.

○ N’utilisez jamais la tronçonneuse sans aucun équipement de

sécurité ou avec un équipement de sécurité inadapté. Cela

pourrait entraîner des blessures graves.

○ Si un guide ou une chaîne diﬀ érente de celle qui a été

recommandée par le fabricant et qui n’est pas homologuée

est utilisé, cela peut entraîner un risque élevé d’accidents

personnels ou de blessures.

Sécurité au niveau du carburant

○ Faites le mélange et le plein à l’air libre, à distance de toute

étincelle ou ﬂ amme.

○ Utilisez un récipient agréé pour l’essence.

○ Ne fumez pas et ne laissez personne fumer à proximité du

carburant ou de la machine, ni lorsque vous utilisez la machine.

○ Essuyez soigneusement toutes les traces de carburant avant de

mettre le moteur en marche.

○ Pour démarrer la tronçonneuse, écartez vous d’au moins 3

mètres de l’endroit où vous avez fait le plein.

○ Arrêtez le moteur avant de dévisser le bouchon du réservoir de

carburant.

○ Vidangez le réservoir de carburant avant de remiser la machine.

Il est en fait recommandé de le faire après chaque utilisation.

Si le réservoir n’est pas vide, rangez alors la machine dans une

position telle que le carburant ne risque pas de couler.

○ Rangez la machine et le carburant dans un endroit où les

vapeurs d’essence ne risquent pas d’entrer en contact avec des

étincelles ou une ﬂ amme en provenance d’un chauﬀ e-eau, d’un

moteur électrique, d’un commutateur, d’une chaudière, etc.

ATTENTION

Le carburant peut s’enﬂ ammer facilement ou exploser

et l’inhalation de ses vapeurs est dangereuse. Faites

particulièrement attention lorsque vous manipulez le carburant

ou faites l’appoint du réservoir.

Sécurité au niveau de la coupe

○ N’essayez pas de couper des matériaux autres que du bois ou

des objets en bois.

○ Pour assurer la protection de vos voies respiratoires, porter un

masque de protection contre les aérosols lorsque vous coupez

du bois qui a été traité avec des insecticides.

○ Éloignez toutes les personnes (enfants, passants, aides, etc.) et

tous les animaux se trouvant dans la zone dangereuse. Arrêtez

immédiatement le moteur si quelqu’un s’approche de vous.

○ Tenez la machine fermement avec la main droite sur la poignée

postérieure et le gauche sur la poignée de devant.

○ Tenez vous bien en équilibre sur vos deux jambes. Ne travaillez

jamais en porte-à-faux.

○ Demeurez toujours éloigné du silencieux d’échappement et de

l’ensemble de coupe lorsque le moteur est en fonctionnement.

○ Maintenir le guide-chaîne en-dessous de la taille.

○ Avant d’abattre un arbre, l’utilisateur devra se familiariser

avec les techniques de coupe et d’abattage à l’aide d’une

tronçonneuse.

○ Avant d’abattre un arbre, assurez-vous de l’existence d’un abri à

proximité.

Français

○ Au cours d’une opération de tronçonnage maintenez la machine

fermement des deux mains avec le pouce bien bloqué autour de

la poignée avant et les pieds bien stables au sol.

○ Tenez-vous légèrement sur le côté de la tronçonneuse lorsque

vous eﬀ ectuez une coupe et non pas dans l’axe derrière la

machine.

○ Maintenez toujours la griﬀ e d’abattage à la surface de l’arbre,

parce que la chaîne peut être entraînée soudainement vers

l’intérieur de l’arbre.

○ Lorsque la coupe est terminée, tenez-vous prêt à tenir

fermement l’outil car il se libère brusquement, pour ne pas en

perdre le contrôle et risquer de vous couper les jambes, les

pieds ou le corps, ni de le toucher.

○ Faites attention aux phénomènes de rebond (lorsque la scie à

chaîne portative avance et recule par rapport à l’opérateur), et

ne coupez jamais avec l’extrémité du guide-chaîne.

○ Quand vous déplacez l’appareil d’un lieu à un autre, vériﬁ ez que

l’appareil est complètement arrêté et que tous les accessoires

de coupe sont à l’arrêt.

○ N e p la cez ja mai s l ’app are il s ur le s ol en c ou rs d e fon ctio nne men t.

○ Assurez-vous toujours que le moteur est arrêté et que tous les

accessoires de coupe sont complètement à l’arrêt avant de

nettoyer l’accessoire principal de coupe de tout débris ou amas

d’herbe.

○ Lors de l’utilisation de n’importe quel appareil électrique/

thermique, emportez toujours avec vous une trousse de

premiers soins.

○ Ne démarrez jamais le moteur de l’appareil, ni n’utilisez jamais

l’appareil dans un local clos ou à l’intérieur d’un bâtiment et/ou

à proximité d’un produit inﬂ ammable. L’inhalation des fumées

d’échappement peut être mortelle.

Sécurité au niveau de l’entretien

○ Entretenez votre machine selon les recommandations du

constructeur.

○ Débranchez la bougie avant toute intervention d’entretien, à

l’exception des opérations de réglages du carburateur.

○ Ne laissez personne s’approcher lorsque vous réglez le

carburateur.

○ Utilisez uniquement les pièces de rechange d’origine HITACHI

recommandées par le fabricant.

IMPORTANT

Ne démontez pas le démarreur de recul de l’appareil. Vous

pourriez vous blesser à cause du ressort de recul.

ATTENTION

Un entretien incorrect peut entraîner des avaries importantes du

moteur ou des blessures graves.

Transpor t et rangement

○ Portez la machine à la main avec moteur arrêté et silencieux

orienté vers l’extérieur, de l’autre côté de votre corps.

○ Laissez le moteur refroidir, videz le réservoir de carburant et

veillez à ce que la machine ne risque pas de tomber lorsque

vous la rangez ou la chargez à bord d’un véhicule.

○ Vidangez le réservoir de carburant avant de ranger la machine.

Il est en fait recommandé de le faire après chaque utilisation.

Si le réservoir n’est pas vide, rangez alors la machine dans une

position telle que le carburant ne risque pas de couler.

○ Rangez la machine hors de portée des enfants.

○ Nettoyez et entretenez la machine soigneusement et rangez-la

dans un endroit sec.

○ Assurez vous que le commutateur d’arrêt du moteur est bien

sur la position d’arrêt lors du transport ou du rangement de la

machine.

○ Lors des transports ou des rangements, recouvrez la chaîne de

son fourreau de protection.

Dans l’éventualité de situations qui ne seraient pas prises en

compte par le présent manuel, redoublez d’attention et de bon sens.

Contactez un concessionnaire HITACHI pour toute assistance.

Faites particulièrement attention aux instructions introduites par les

mots suivants.

ATTENTION

Instructions de première importance pour éviter des dommages

corporels graves ou mortels.

IMPORTANT

Instructions importantes aﬁ n d’éviter des dommages corporels ou

matériels.

REMARQUE

Informations pratiques pour la compréhension d’une intervention.

Français

SPÉCIFICATIONS

○ Le code “CS” du nom de modèle signiﬁ e “Chain Saw” (tronçonneuse)

Modèle CS40EA (45PS)

Type d’équipement Tronçonneuse portative

Taille du moteur (cu. in.) 2.41 (39.6 ml)

Bougie d’allumage NGK BPM-7A ou BPMR-7A ou équivalent

Contenance du réservoir de

carburant (Pinte des USA)

0.80 (380 ml)

Contenance du réservoir d’huile de

chaîne (Pinte des USA)

0.51 (240 ml)

Poids à sec (livre)

(Sans le guide-chaîne et la chaîne)

9.9 (4.5 kg)

Longueur du guide-chaîne (in.) 18 (450 mm)

Pas de chaîne (in.)

0.325 8.26 mm)

Calibre de chaîne (in.) 0.05 (1.27 mm)

Niveau de pression acoustique

LpA (dB (A))

par ISO 22868

103

Niveau de puissance sonore

Lw mesuré (dB (A))

par ISO 22868

Niveau de puissance sonore LwA

(dB (A))

par 2000/14/EC

113

114

Niveau de vibrations (m/s

)

par ISO 22867

Poignée avant

Poignée arrière

2.2

3.2

Puissance max. du moteur

selon ISO 7293 (kW)

1.8/10500

Régime max. du moteur (min

-1

) 13000

Régime de ralenti (min

-1

) 3000

Consommation spéciﬁ que (g/kWh) 480

Type de chaîne

95VP

(Oregon)

Vitesse max. de chaîne (m/sec) 23.1

Pignon (nombre de dents) 7

REMARQUE : Les niveaux de bruit/vibrations équivalents sont calculés comme total d’énergie pondérée en fonction du temps pour les

niveaux de bruit/vibrations dans diverses conditions de travail avec la répartition temporelle suivante : 1/3 ralenti, 1/3 plein

régime, 1/3 vitesse de course.

* Toutes les données sont sujettes à modiﬁ cation sans préavis.

Les valeurs d’émission de bruit singulier déclarées sont la somme des valeurs mesurées et des incertitudes correspondantes

de 3dB et elles représentent les limites supérieures des valeurs qui surviendront probablement lors des mesures.

La page est en cours de chargement...

Hitachi CS 40EA Manuel utilisateur

Marque: Hitachi

Modèle: CS 40EA

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

CS40EA18

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi CS 40EA User manual
español: Hitachi CS 40EA Manual de usuario

Hitachi CS 40EA Manuel utilisateur

Ce manuel convient également à

Hitachi CS 40EA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents