GAS/OIL
RATIO
50:1
Operator's Manual
Original Operating Instructions
E43/E43CE
1-Man Earth Auger
Powerhead
P/N: 18412
ECN: 10810
REV2: 04/24/15
© 2015 Ardisam, Inc.
All Rights Reserved
Get parts online at
www.GetEarthquake.com
SN
English: ...................Pages 1-24
Español: ............Páginas 25-50
Français: .............Pages 51-80
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
2
INTRODUCTION
Congratulations on your investment in quality. Thank you for purchasing an Earthquake™ E43™ Powerhead. We have worked to
ensure that your powerhead meets the highest standards for usability and durability. With proper care, your powerhead will provide
many years of service.
Read this entire manual before installation and use. Earthquake reserves the right to change, alter or improve the product
and this document at any time without prior notice.
CONTENTS
Introduction .......................................................................................................................................................................................................................................2
Warnings and Safety Precautions ...........................................................................................................................................................................................3-6
Specications .....................................................................................................................................................................................................................................8
Assembly .............................................................................................................................................................................................................................................8
Operation ......................................................................................................................................................................................................................................9-10
Maintenance and Storage .................................................................................................................................................................................................... 11-13
Troubleshooting and Repair .......................................................................................................................................................................................................14
Parts Breakdown ......................................................................................................................................................................................................................15-19
Warranty .....................................................................................................................................................................................................................................20-22
CE Declaration of Conformity ....................................................................................................................................................................................................23
FEDERAL EMISSION INFORMATION
Ardisam warrants to the retail purchaser, that this small, o-road engine was designed, built and equipped to conform at the
time of manufacture to all applicable regulations of the U.S. Environmental Protection Agency (EPA) and those of the State of
California (CARB) when applicable.
REGISTRATION AND SERVICE
This manual may contain information for several models. Read and keep this manual for future reference. This manual contains impor-
tant information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. The owner must be certain that all the product information
is included with the unit. This information includes the MANUAL, the REPLACEMENT PARTS and the WARRANTIES. This information
must be included to make sure state laws and other laws are followed. This manual should remain with the engine even if it is resold.
OWNERSHIP RECORDS
Owner’s Name:
Owner’s Address:
City: State/Province: Zip Code/Postal Code:
Model Number: Serial Number:
Date of Purchase:
Notes:
Record the model number and serial number in the space provided for easy reference when
ordering parts or requesting technical support. Excluding emissions-related warranty items,
the warranty is valid only if the completed registration is received by Earthquake within 30
days of purchase. (SEE WARRANTY SECTION FOR MORE INFORMATION.) You can register
your warranty online by visiting www.getearthquake.com, or by mailing it to: Earthquake,
1160 Eighth Avenue, Cumberland, WI 54829. If you do not have a computer, call our customer
service department to register your product.
2
1
5
4
3
7
6
CE
USA
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 3
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
WARNINGS AND SAFETY PRECAUTIONS
OPERATOR’S RESPONSIBILITY
Accurate, safe and eective use of this product is the operator’s
responsibility.
included in this operator’s manual.
and understands all controls and safety precautions.
SAFETY MESSAGES
Your manual contains special messages to bring attention to
potential safety concerns, machine damage as well as helpful
operating and servicing information. Read all the information
carefully to avoid injury and machine damage.
NOTE: General information is given throughout the manual
that may help the operator in the operation or service of the
product.
This symbol points out important safety instruc-
tions which if not followed could endanger your
personal safety.
BEFORE OPERATING ENGINE:
WARNING
WARNING INDICATES A HAZARD WHICH, IF NOT
AVOIDED, COULD RESULT IN DEATH OR SERIOUS IN
JURY AND/OR PROPERTY DAMAGE.
CAUTION
CAUTION INDICATES YOU CAN BE HURT OR YOUR
EQUIPMENT DAMAGED IF THE SAFETY INSTRUC
TIONS THAT FOLLOW THIS SIGNAL WORD ARE NOT
OBEYED.
WARNING
CALIFORNIA PROPOSITION 65 WARNING
ENGINE EXHAUST FROM THIS PRODUCT CONTAINS
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER RE
PRODUCTIVE HARM.
IMPORTANT
INDICATES HELPFUL INFORMATION FOR PROPER AS
SEMBLY, OPERATION, OR MAINTENANCE OF YOUR
EQUIPMENT.
WARNING
READ AND COMPLY WITH ENTIRE OPERATING AND
MAINTENANCE INSTRUCTIONS FOR THIS MACHINE,
IN ADDITIONAL TO ALL SAFETY INSTRUCTIONS. FAIL
URE TO FOLLOW AND/OR COMPLY WITH THESE IN
STRUCTIONS COULD RESULT IN LOSS OF MACHINE
CONTROL, SERIOUS PERSONAL INJURY OR DEATH TO
YOU AND/OR BYSTANDERS, AND EQUIPMENT AND
PROPERTY DAMAGE. OPERATE THE ENGINE ACCORD
ING TO THE SAFETY INSTRUCTIONS OUTLINED HERE
AND INSERTED THROUGHOUT THE TEXT. ANYONE
WHO USES THIS MACHINE MUST READ THE INSTRUC
TIONS AND BE FAMILIAR WITH THE CONTROLS.
WARNING
CERTAIN COMPONENTS IN THIS MACHINE AND ITS RE
LATED ACCESSORIES CONTAIN CHEMICALS KNOWN
TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM.
WASH HANDS AFTER HANDLING.
Intended Use /
Foreseeable Misuse
This is a motorized earth auger powerhead that drills into soil. It
is pedestrian controlled. It has a petrol-fueled internal combus-
tion engine that powers the auger blades. It shall not be used
for any other purpose.
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
4
GENERAL SAFETY RULES
Read, understand, and follow all instructions on the ma-
chine and in the manual(s). Be thoroughly familiar with the
controls and the proper use of the machine before starting.
Use this equipment for its intended purpose only.
Familiarize yourself with all of the safety and operating
decals on this equipment and on any of its attachments or
accessories.
Do not put hands or feet near or under rotating parts.
Only allow responsible individuals who are familiar with the
instructions to operate the machine. Do not allow children
to operate this machine. Do not allow adults to operate the
machine without proper instruction.
Thoroughly inspect the area where the machine is to be
used and remove all foreign objects. Your equipment can
propel small objects at high speed causing personal injury
or property damage. Stay away from breakable objects such
as house windows.
Wear appropriate clothing such as a long-sleeved shirt or
jacket. Also wear long trousers or slacks. Do not wear shorts.
Never wear sandals, sneakers, or open shoes, and never
operate the machine with bare feet.
Do not wear loose clothing or jewelry. They can get caught in
moving parts. Always keep hands, feet, hair and loose clothing
away from any moving parts on engine and machine.
Always wear safety goggles or safety glasses with side shields
when operating the machine to protect your eyes from
foreign objects which can be thrown from the unit. Always
wear a protective hearing device.
Always wear work gloves and sturdy footwear. Wear
footwear that will improve footing on slippery surfaces.
Leather work shoes or short boots work well for most people.
These will protect the operator’s ankles and shins from small
sticks, splinters, and other debris.
It is advisable to wear protective headgear to prevent the
possibility of being struck by small ying particles, or being
struck by low hanging branches, twigs, or other objects
which may be unnoticed by the operator.
Do not operate the machine without proper guards or other
safety devices in place.
See Earthquake instructions for proper operation and
installation of accessories. Only use accessories approved
by Earthquake.
Operate only in daylight or good articial light.
Do not operate machine when fatigued or under the
influence of alcohol, drugs or other medication which
can cause drowsiness or aect your ability to operate this
machine safely.
Never operate machine in wet grass. Always be sure of your
footing; keep a rm hold on the handle and walk; never run.
Watch for traffic when operating near, or when
crossing roads.
If the equipment should start to vibrate abnormally, stop the
engine (motor), disconnect the spark plug wire and prevent
it from touching the spark plug. Check immediately for cause.
Vibration is generally a warning of trouble. If the noise or
vibrations of the machine increase, stop immediately and
perform an inspection.
Never leave the machine unattended when the engine is
running.
Regularly inspect the machine. Make sure parts are not bent,
damaged or loose.
Temperature of muer and nearby areas may exceed 150° F
(65° C). Allow muer and engine areas to cool before touching.
Never pick up or carry the machine while the engine is running.
Prolonged exposure to noise and vibration from gasoline engine-
powered equipment should be avoided. Take intermittent
breaks and/or wear ear protection from engine noise as well as
heavy work gloves to reduce vibration in the hands.
Keep all screws, nuts and bolts tight.
Do not transport the machine from one place to another
with the engine running.
Check local regulations for age restrictions on use of this
machine.
PRODUCTSPECIFIC SAFETY RULES
Do not drill above underground utilities, including water
lines, gas lines, electric cables, or pipes. Do not operate the
powerhead and earth auger in soil with large rocks and
foreign objects which can damage the equipment.
After striking a foreign object, stop the engine. Remove the
wire from the spark plug. Inspect the powerhead and auger
for damage. If damaged, repair before starting and operating
the powerhead and auger.
The auger should not rotate when the engine is idling. If it
does rotate when engine is idling, contact Earthquake for
instructions.
If an object becomes lodged in the auger, turn the engine o,
remove the wire from the spark plug and secure away from
the spark plug; allow to cool before attempting to remove
the foreign object.
The earth blade is very sharp. Use extreme caution when
drilling a hole or replacing the blade.
Do not carry the earth auger unit between holes with the
engine running.
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 5
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
CAUTION
HOT GASES ARE A NORMAL BYPRODUCT OF A FUNC
TIONING CATALYTIC CONVERTER. FOLLOW ALL SAFE
TY INSTRUCTIONS TO PREVENT BURNS AND FIRES.
DO NOT ALTER/MODIFY ENGINE:
NEVER ALTER OR MODIFY THE ENGINE FROM THE
FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF
ENGINE IS MODIFIED OR ALTERED.
WHEN WORKING ON OR REPLACING PARTS FOR THE
ENGINE OR MACHINE, YOU MUST ALWAYS DISCON
NECT THE SPARK PLUG WIRE FROM THE SPARK PLUG
AND KEEP IT AWAY FROM THE SPARK PLUG.
ENGINE SAFETY PRECAUTIONS
Warning Carbon Monoxide Poisoning
Engines give off carbon monoxide, an odorless, colorless,
poison gas. Carbon monoxide may be present even if you do not
smell or see any engine exhaust. Breathing carbon monoxide
can cause nausea, fainting or death, in addition to drowsiness,
dizziness and confusion. If you experience any of these
symptoms, seek fresh air and medical attention immediately.
If your machine comes with a separate engine manual, be
sure to read and follow all safety and warning precautions
outlined there, in addition to any in this manual.
Preventing Carbon Monoxide Poisoning
Always start and run engine outdoors. Do not start or run
engine in an enclosed area, even if doors or windows are open.
Never try to ventilate engine exhaust indoors. Carbon
monoxide can reach dangerous levels very quickly.
Never run engine outdoors where exhaust fumes may be
pulled into a building.
Never run engine outdoors in a poorly ventilated area where
the exhaust fumes may be trapped and not easily taken
away. (Examples include: in a large hole or areas where hills
surround your working area.)
Never run engine in an enclosed or partially enclosed area.
(Examples include: buildings that are enclosed on one or
more sides, under tents, car ports or basements.)
Always run the engine with the exhaust and muer pointed
in the direction away from the operator.
Never point the exhaust muer towards anyone. People
should always be many feet away from the operation of the
engine and its attachments.
Do not change the engine governor settings or over-speed
the engine.
WARNING
ENGINES GIVE OFF CARBON MONOXIDE, AN ODOR
LESS, COLORLESS, POISON GAS. CARBON MONOXIDE
MAY BE PRESENT EVEN IF YOU DO NOT SMELL OR SEE
ANY ENGINE EXHAUST. BREATHING CARBON MON
OXIDE CAN CAUSE NAUSEA, FAINTING OR DEATH, IN
ADDITION TO DROWSINESS, DIZZINESS AND CONFU
SION.
IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK
FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.
Gasoline Fires and Handling Fuel Safely
Use extra care in handling gasoline and other fuels. They are
ammable and vapors are explosive.
When storing extra fuel be sure that it is in an appropriate
container and away from any re hazards.
Prevent re and explosion caused by static electric discharge.
Use only nonmetal, portable fuel containers approved by the
Underwriter’s Laboratory (U.L.) or the American Society for
Testing & Materials (ASTM).
Always ll fuel tank outside in a well ventilated area. Never
fill your fuel tank with fuel indoors. (Examples include:
basement, garage, barn, shed, house, porch, etc.) Never
ll tank near appliances with pilot lights, heaters, or other
ignition sources. If the fuel has to be drained, this should
be done outdoors. The drained fuel should be stored in a
container specically designed for fuel storage or it should
be disposed of carefully.
Never remove the fuel cap or add fuel with the engine
running. Stop engine and allow to cool before lling.
Do not smoke while refueling or operating engine.
Never drain fuel from the engine in an enclosed area.
Always wipe up excess (spilled) fuel from engine before
starting. Clean up spilled fuel immediately. If fuel is spilled,
do not start the engine but move machine and fuel container
from area. Clean up spilled fuel and allow to evaporate and
dry after wiping and before starting.
Allow fuel fumes/vapors to escape from the area before
starting engine.
Test the fuel cap for proper installation before starting and
using engine.
Always run the engine with fuel cap properly installed on
the engine.
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
6
Do not store engine with fuel in the fuel tank indoors. Fuel
and fuel vapors are highly explosive.
During storage, keep machine so gas cap is up.
Never siphon fuel by mouth to drain fuel tank.
Always have an adult fill the fuel tank and never allow
children to ll the engine.
Never allow an adult or anyone under the inuence of drugs
or alcohol to ll engine.
When storing gasoline or equipment with fuel in the tank,
store away from furnaces, stoves, water heaters or other
appliances that have a pilot light or other ignition source
because they can ignite gasoline vapors.
BURNS AND FIRES
The muer, muer guard and other parts of the engine be-
come extremely hot during the operation of the engine. These
parts remain extremely hot after the engine has stopped.
Prevention of Burns and Fires
and will cause severe burns.
operation.
and other hot parts of the engine to avoid res.
CHILDREN AND BYSTANDERS
Tragic accidents can occur if the operator is not alert to the
presence of children and/or bystanders. Never assume that
others will remain where you last saw them.
Keep the area of operation clear of all persons, especially
small children and pets. Keep children under the watchful
care of a responsible adult.
Be alert and turn the machine o if children enter the area.
Before and while moving backwards, look behind and down
for small children.
Never allow children to operate the machine
AUGER SAFETY RULES
Carry powerhead and auger by handle bars only, NOT by
auger.
Keep all body extremities, loose clothing and foreign objects
clear of rotating auger.
Be sure auger is securely attached to powerhead during use.
Never carry auger between holes with the engine running.
This auger is not designed to be utilized as an anchoring
device.
SERVICE
Always stop the engine whenever you leave the machine,
before cleaning, repairing or inspecting the unit. The
engine should be turned o and cool, the spark plug wire
must be removed from the spark plug before any repairs
or adjustments are attempted. Never make adjustments
or repairs with the engine (motor) running. Disconnect
the spark plug wire, and keep the wire away from the plug
to prevent accidental starting. Remove the ignition key if
equipped with an electric start.
Always wear eye protection when you make adjustments or
repairs.
Keep all nuts and bolts tight and keep equipment in good
condition.
Never tamper with safety devices. Check their proper
operation regularly.
When servicing or repairing the machine, do not tip the
machine over or up unless specically instructed to do so in
this manual. Service and repair procedures can be done with
the machine in an upright position. Some procedures will be
easier if the machine is lifted on a raised platform or working
surface.
To reduce re hazard, keep machine free of grass, leaves,
or other debris build-up. Clean up oil or fuel spillage. Allow
machine to cool before storing.
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
Clean and replace safety and instruction decals as necessary.
To guard against engine over-heating, always have engine
debris lter mounted and clean.
Inspect the machine before storage. When not in use,
disconnect the spark plug lead and store indoors in a dry
place locked or otherwise inaccessible to children.
Use only original equipment parts from Earthquake,
including all nuts and bolts.
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 7
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
GAS/OIL
RATIO
50:1
Fire hazards
Wear hearing and
eye protection
Shock hazard
Hot surfaces
Toxic fumes
Moving parts
Read manual before operation
Slow
Fast
Fuel
Oil
Choke
On/O
Fuel Shuto
SAFETY SYMBOLS AND DECALS
C
GAS/OIL
RATIO
50:1
Operational Control Symbols
This powerhead has been designed and manufactured to provide you with the safety and reliability you would expect from an
industry leader in outdoor power equipment manufacturing.
Reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this
equipment safely and eectively. We have placed a safety decal on the powerhead to remind you of some of this important information
while you are operating the unit. These important safety decals are illustrated below, and are shown here to help familiarize you
with the location and content of the safety messages you will see as you perform normal drilling operations. Review these decals
now, and if you have any questions regarding their meaning or how to comply with these instructions, reread the complete safety
instruction text in this manual. For additional questions European customers may contact their local dealer while US customers must
call Earthquake customer service.
Should a decal become unreadable because of being worn, faded, or otherwise damaged during the use of your powerhead, use the
part number information provided to order a replacement label. European customers can order from their local authorized dealer
while US customers can order by calling Earthquake customer service. These decals are easily applied, and will act as a constant visual
reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, eective operation of
your powerhead.
The following symbols and decals may be used on your engine to alert you to potential hazards or to give you guidance in operating
your powerhead. Look over them and understand their meanings before operating your powerhead.
Safety or Hazard Symbols
Hot! Do not touch!
Part No. 18481
SERIAL NUMBER
DECAL
Part No. LBLVE43
E43 SHROUD DECAL
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
8
ASSEMBLY
TOOLS REQUIRED:
ASSEMBLY INSTRUCTIONS: SEE FIGURE 1
1. Insert the output shaft of the E43 transmission (A) in the open end
of the Flex Coil ShockTop (B).
2. Line up the bolt holes through the Flex Coil ShockTop and the output
shaft of the transmission.
3. Place the included 3/8-16 x 1.5 inch bolt (C) through the bolt hole.
4. Hand-thread the 3/8-16 nut (D) on the bolt.
5. Using two 9/16 inch wrenches, securely tighten the nut and bolt.
E43 and EA6F shown. Instructions also apply to EA8F and EA10F
augers.
A
B
D
C
Figure 1
SPECIFICATIONS
Model Operator Ear
L
PA
(dBA)
Sound Power Level
L
WA
(dBA)
E43 100 106
SOUND AND VIBRATION LEVELS
Model Hand/Arm Vibration
Max m/s
2
E43 16.1
Sound levels tested in accordance with ISO3744 & ISO 11201 - Grade 2
(Engineering ) Method. Readings taken with engine at full throttle.
EAV = Exposure Action Value, ELV = Exposure Limit Value
Displacement/Cycle 43 cc; 2-cycle
Ignition Type Electronic ignition
Cooling System Forced air cooling
Output Shaft Torque 46.5 ft. lb.
Spark Plug Type SEE PARTS BREAKDOWN
Recommended Fuel Type Minimum 87 octane gasoline with
NO ethanol content
NOTE: If using an ethanol blended
fuel, a fuel stabilizer, mixed to
manufacturer specications, is
recommended
Fuel Tank Capacity 0.3 gallon (1.14 liters)
Start Type Recoil
Output Shaft Speed at Max Torque
167 RPM
Output Shaft Speed at Max Power
217 RPM
Net Weight 24 lb (9.53 kg)
Overall Dimensions
339mm x 279mm)
WARNING
DO NOT REFUEL WHILE SMOKING, NEAR OPEN FLAME,
OR OTHER POTENTIAL HAZARDS.
FUEL IS HIGHLY FLAMMABLE AND MUST BE HANDLED
WITH CARE. NEVER FILL THE TANK WHEN THE ENGINE
IS HOT OR RUNNING. ALWAYS MOVE OUTDOORS TO
FILL THE TANK.
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 9
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
OPERATION
GAS AND OIL QUALITY
To operate the engine, we recommend using Viper® brand 2-cycle
oil (P/N 16890) to ensure that the engine operates correctly
throughout the life of the engine. Viper® brand two-cycle oil
has fuel stabilizer additive which helps to prevent gasoline from
oxidizing and gumming up the carburetor when the unit is not
in use for long periods of time. Use unleaded regular gas only.
It is best to use premium gasoline that has no ethanol content.
NOTE: Viper® oil can be purchased from our web site at www.
getearthquake.com.
MIXTURE
Run earth auger with a 50:1 ratio.
MIXING FUEL AND FILLING GAS TANK
MIXING FUEL
1. Fuel must be mixed in a container outside in a well ventilated
area.
2. Fill certied fuel container 1/4 full of recommended fuel.
3. Add recommended amount of 2 cycle oil.
4. Screw container cap on straight and tight.
5. Shake the container to mix fuel and oil.
6. Unscrew gas cap slowly to vent, add the remainder of fuel
requirements.
7. Wipe away any spilled fuel or oil and allow to evaporate before
moving or transporting.
FILLING FUEL TANK
1. Shut-o engine and allow engine to completely cool before
relling the fuel tank.
2. Move to a well-ventilated area, outdoors, away from ames
and sparks.
3. Clean debris from area around the fuel cap.
4. Loosen fuel cap slowly.
5. Carefully add fuel without spilling.
6. Do not ll fuel tank completely full; allow space for fuel to expand.
7. Immediately replace fuel cap and tighten. Wipe o spilled
fuel and allow to dry before starting engine.
GAS OIL RATIO
1 gallon 2.5 ounces 50:1
2 gallons 5 ounces 50:1
5 gallons 13 ounces 50:1
CAUTION
DO NOT ALTER/MODIFY ENGINE OR AUGER:
NEVER ALTER OR MODIFY THE ENGINE FROM THE
FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF
ENGINE IS MODIFIED OR ALTERED.
WHEN WORKING ON OR REPLACING PARTS FOR THE
ENGINE OR AUGER YOU MUST ALWAYS DISCONNECT
THE SPARK PLUG WIRE FROM THE SPARK PLUG AND
KEEP IT AWAY FROM THE SPARK PLUG.
ALWAYS WEAR HEARING PROTECTION WHILE OPER
ATING ENGINE.
DO NOT START YOUR EARTH AUGER UNTIL YOU HAVE
READ THE PREVIOUS SECTION OF THIS MANUAL. IF
YOU HAVE READ THESE, FOLLOW THE STEPS BELOW
TO START YOUR EARTH AUGER.
NEVER STORE ENGINE WITH GAS IN THE TANK INDOORS.
FUEL AND FUEL VAPORS ARE HIGHLY FLAMMABLE.
NEVER MIX FUEL AND OIL DIRECTLY IN ENGINE GAS
TANK. USE ONLY NONMETAL, PORTABLE FUEL CON
TAINERS APPROVED BY THE UNDERWRITER’S LABO
RATORY U.L. OR THE AMERICAN SOCIETY FOR TEST
ING & MATERIALS ASTM.
HANDLING AND FILLING THE ENGINE WITH FUEL
MUST ALWAYS BE DONE BY AN ADULT.
ALWAYS HANDLE FUEL IN A WELL VENTILATED AREA,
OUTDOORS, AWAY FROM FLAMES OR SPARKS.
IMPORTANT
THIS ENGINE USES A GAS/OIL MIXTURE. DO NOT RUN ON
STRAIGHT GAS ONLY. THIS WILL VOID THE WARRANTY
AND ENGINE DAMAGE WILL RESULT.
NORMAL OPERATION
1. The clutch will transfer maximum power after about two hours of
normal operation. During this break-in period, clutch slippage may
occur. The clutch should be kept free of oil or other moisture for
ecient operation.
2. Drill holes without placing excessive body weight on the unit. The
auger operates most eciently with a shaving action caused by the
weight of the unit itself.
3. Never run engine indoors. Exhaust fumes are deadly.
4. Do not use an earth auger in the ice.
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
10
WARNING
MAKE SURE THE UNIT IS IN A STABLE POSITION BEFORE
PULLING THE STARTER HANDLE.
WHEN THE UNIT STARTS TO FIRE OR RUN, RELEASE THE
THROTTLE CONTROL MOMENTARILY WITH YOUR RIGHT
HAND AND RETURN YOUR LEFT HAND TO THE HANDLEBAR
POSITION TO MAINTAIN CONTROL AND STABILITY OF THE
UNIT WITH BOTH HANDS.
STARTING AND STOPPING ENGINE
carbon monoxide poisoning.
of vapors if present.
proper air ow.
COLD ENGINE START
Starting engine for rst time or after engine has cooled o or
after running out of fuel.
1. Move choke lever to CHOKE position.
NOTE: CHOKE position is dened by moving the choke lever
as far to the CHOKE position as possible.
2. Prime unit until primer hose is lled with gas.
NOTE: When using the primer bulb, allow the bulb to return
completely to its original position between pushes.
4. Push ON/OFF switch to the ON position.
5. Hold handle bar rmly. Grasp starter handle and pull out slowly,
until it pulls slightly harder. Without letting starter handle retract,
pull rope with a rapid full arm stroke. Let it return to its original
position very slowly until unit res or runs. Repeat this step every
time the starter rope is pulled.
NOTE: If engine fails to start after 5-6 pulls, push primer 1
time and pull starter rope again.
6. Once running, move choke lever to HALF CHOKE position
until unit runs smoothly.
NOTE: HALF CHOKE is dened when the choke lever is be-
tween CHOKE and RUN.
7. Move choke lever to RUN position and move throttle to de-
sired speed.
NOTE: Run at full throttle when possible. Do not let unit idle
for extended periods of time.
8. To stop engine, push ON/OFF switch to OFF position.
WARM ENGINE START
1. Move choke lever to CHOKE position.
NOTE: CHOKE position is dened by moving the choke lever
as far to the CHOKE position as possible.
2. Continue with Step 4 of Cold Engine Starting.
CAUTION
MAKE SURE THE UNIT IS IN A STABLE POSITION BE
FORE PULLING THE STARTER HANDLE.
ALWAYS HANDLE FUEL IN A WELL VENTILATED AREA,
OUTDOORS, AWAY FROM FLAMES OR SPARKS.
ALWAYS WEAR A PROTECTIVE HEARING DEVICE.
DO NOT START ENGINE IF FUEL IS SPILLED. WIPE OFF
EXCESS FUEL AND ALLOW TO DRY. REMOVE ENGINE
FROM AREA TO AVOID SPARKS.
IF AUGER IS MOUNTED TO ENGINE, ALL SAFETY
GUARDS MUST BE SECURELY ON TO AVOID SERIOUS
INJURY.
STARTER ROPE CAN CAUSE AN UNANTICIPATED
JERK TOWARDS ENGINE. FOLLOW INSTRUCTIONS TO
AVOID INJURY.
IF ENGINE FAILS TO START AFTER TRYING STARTING
PROCEDURES, CONTACT OUR CUSTOMER SERVICE
DEPARTMENT AT 8003456007.
NEVER LEAVE ENGINE RUNNING WHILE UNATTEND
ED. TURN OFF AFTER EVERY USE.
NEVER CARRY POWERHEAD AND AUGER BETWEEN
HOLES WHILE ENGINE IS RUNNING.
HOT ENGINE START:
1. Begin with Step 4 of Cold Engine Starting.
2. If engine does not re, refer to Step 1 of Warm Engine Starting.
DO NOT attempt to start engine in the following ways:
• Byusingstartinguid.
• Spraying ammableliquidsorvaporsintoaircleaner,
carburetor or spark plug chamber.
• Removingsparkplugandpullonstarterrope.Flammable
fuel can spray out and ignite from a spark from spark plug.
TO STOP ENGINE:
Push the ON/OFF switch to the OFF position.
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 11
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
MAINTENANCE AND STORAGE
STEPS FOR WORKING ON EQUIPMENT
1. Turn o engine switch.
2. Disconnect the spark plug wire from the spark plug.
3. Securely place the disconnected spark plug wire away from
the spark plug and any metal parts. This must always be done
or arcing may occur between spark plug wire and metal parts.
4. Replace or repair the part on the powerhead.
5. Check all parts that were repaired, or removed during repair,
that they are secure and t correctly.
NOTE: All repair parts must come from the factory. Never
replace parts that are not specifically designed for the
powerhead.
6. Reconnect the spark plug wire.
POWER AUGER MAINTENANCE
1. The gear case has 4 oz. of grease installed at the factory. It
is recommended that once a year the gear case be split and
the grease level checked. Add grease only if level of grease
is below top of the gears. DO NOT OVERFILL. Replacement
grease is available online per parts breakdown.
2. Keep all screws, nuts, and bolts tight.
3. For cold weather operation, store the unit in a cool environ-
ment. Transferring the unit from a warm to a cold place can
cause the build up of harmful condensation.
4. If auger performance decreases, carefully inspect cutting edge
of blade for any signs of wear. If blades show any of these signs,
they need to be replaced.
ENGINE MAINTENANCE
Read the maintenance schedule and observe these recommen-
dations to extend the life of your engine.
Good maintenance is essential for safe, economical, and trou-
ble-free operation. It will also help reduce air pollution. To help
you properly care for your engine, the following pages include
a maintenance schedule, routine inspection procedures, and
simple maintenance procedures using basic hand tools. Other
service tasks that are more difficult, or require special tools, are
best handled by professionals and are normally performed by a
technician or other qualified mechanic.
Maintenance, replacement or repair of the emissions con-
trol devices and systems may be performed by any non-
road engine repair establishment or individuals. However,
items must be serviced by an authorized dealer to obtain
"no charge" emissions control service.
CAUTION
TO PREVENT ACCIDENTAL STARTING:
ENGINE MUST BE TURNED OFF AND COOL, AND
SPARK PLUG WIRE MUST BE REMOVED FROM SPARK
PLUG BEFORE CHECKING AND ADJUSTING ENGINE
OR EQUIPMENT.
TEMPERATURE OF MUFFLER AND NEARBY AREAS
MAY EXCEED 150º F. 65º C. AVOID THESE AREAS.
CHECK AUGER OFTEN FOR LOOSE NUTS AND BOLTS.
KEEP THESE ITEMS TIGHTENED.
NEVER STORE ENGINE WITH FUEL IN THE TANK IN
SIDE A BUILDING. POTENTIAL SPARKS MAY BE PRES
ENT FOR IGNITION OF FUEL AND FUEL VAPORS.
ANY MAINTENANCE AND REPAIR ON THE ENGINE
AND AUGER MUST ALWAYS BE DONE BY AN ADULT.
ENGINE MUST BE SHUTOFF, COOL, AND SPARK PLUG
WIRE REMOVED BEFORE ANY REPAIR OR MAINTE
NANCE CAN BE DONE.
MAINTENANCE ITEM
Every 8
hours
(daily)
Every 20
hours or
seasonally Yearly
Clean Engine and Check Bolts & Nuts X
Air Filter Check X
(See Air Filter section) Clean * X
Replace X
Check/
Adjust
X
(See Spark Plug
section)
Replace X
* Service more frequently under dusty conditions
MAINTENANCE SCHEDULE
IMPORTANT
NEVER TWIST AIR FILTERS WHEN CLEANING. ALWAYS
PRESS.
The maintenance schedule applies to normal operating condi-
tions. If you operate your engine under unusual conditions, such
as sustained high-load or high-temperature operation, or use in
unusually wet or dusty conditions, consult your servicing dealer
for recommendations applicable to your individual needs and use.
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
12
COOLING FINS
Cooling ns, air inlets and linkages must be free from any debris
before each use.
AIR FILTER
Never run engine without air cleaner properly installed. Added
wear and engine failure may occur if air cleaner is not installed
on engine.
Service air cleaner every 3 months or after 20 hours of operation.
Clean lter daily in extremely dusty conditions.
STEPS FOR CLEANING BLOCK STYLE FOAM AIR FILTER
1. Before removing the air lter cover, move the choke lever to
the choke position. SEE FIGURE 2.
2. To remove air lter cover, squeeze the latch tabs on both sides
of the cover. SEE FIGURE 3.
3. Once the latch tabs are released, remove the air lter cover
by rotating the cover away from the engine. SEE FIGURE 4.
4. Remove the foam lter element (SEE FIGURE 5) and replace
with a new oiled lter, or clean the original foam lter with
warm water and mild soap by following the previous steps for
Cleaning Air Filter. Remember to thoroughly oil the foam lter
with 30 or 40 weight motor oil and squeeze out any excess
oil.
5. Reinstall the foam lter, pressing it in place to ensure that the
foam is fully seated into its sealed position. SEE FIGURE 6.
6. Replace the air lter cover so that it fully snaps into place and
is secured by the latch tabs. Check that the cover is securely
attached by pulling slightly on the cover. If the cover doesn’t
move when pulled, it is secure.
Figure 2
Figure 3
Figure 4 Figure 5
Figure 6
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 13
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
SPARK PLUG
See parts breakdown for recommended spark plug.
1. Check spark plug at the beginning of each season.
2. Disconnect the spark plug cap, and clean any debris from
around the spark plug area.
3. Remove spark plug and replace if any of the following occur;
pitted electrodes, burned electrodes, cracked porcelain, or
deposits around electrodes.
4. After analysis, seat spark plug and tighten with spark plug
wrench.
tighten additional 1/8 – 1/4 turn .
NOTE: Loose spark plug may overheat and damage engine.
Over tightened spark plug may damage threads in the
cylinder head.
CARBURETOR
Never tamper with factory setting of the carburetor.
TRANSPORTING YOUR EARTH AUGER
1. Never transport engine inside an enclosed space or vehicle.
Fuel or fuel vapors may ignite causing serious injury or death.
2. If fuel is present in the fuel tank, transport in an open vehicle
in an upright position.
3. If an enclosed vehicle must be used, remove gas into an ap-
proved red fuel container. DO NOT siphon by mouth.
4. Run engine to use up the fuel in the carburetor and fuel tank.
Always run engine in a well ventilated area.
5. Wipe away any spilled fuel from engine and earth auger. Allow
to dry.
LONGTERM STORAGE
30 DAYS OR MORE WITHOUT USE
If your earth auger will not be used for more than one month,
prepare it for long term storage.
STEPS FOR LONGTERM STORAGE
1. Add fuel stabilizer according to manufacturer’s instructions.
2. Run engine for 10-15 minutes to ensure that the stabilizer
reaches the carburetor.
3. Remove the remainder of the fuel from the gas tank into an
approved fuel container.
4. Remove auger from powerhead and apply a thin layer of
grease to the output shaft of the transmission.
5. Store auger and powerhead (engine) in a vertical position.
6. Remove all debris from auger and powerhead (engine).
CAUTION
TO AVOID INJURY OR DEATH, NEVER SIPHON FUEL BY
MOUTH.
NEVER STORE EARTH AUGER WITH FUEL IN THE GAS
TANK INSIDE AN ENCLOSED AREA OR BUILDING.
TO PREVENT ACCIDENTAL STARTING:
ENGINE MUST BE TURNED OFF AND COOL, AND
SPARK PLUG WIRE MUST BE REMOVED FROM SPARK
PLUG BEFORE CHECKING AND ADJUSTING ENGINE
OR EQUIPMENT.
MAINTENANCE AND REPAIR ON THE ENGINE AND AU
GER MUST ALWAYS BE DONE BY AN ADULT.
ENGINE MUST BE SHUTOFF, COOL, AND SPARK PLUG
WIRE REMOVED BEFORE ANY REPAIR OR MAINTE
NANCE CAN BE DONE.
TROUBLESHOOTING AND REPAIR
At Earthquake, we build quality and durability into the design of
our products; but no amount of careful design by us, and careful
maintenance by you, can guarantee a repair-free life for your
Earthquake powerhead. Most repairs will be minor, and easily
xed by following the suggestions in the troubleshooting guide
in this manual.
The troubleshooting guide will help you pinpoint the causes of
common problems and identify remedies.
For more complicated repairs, you may want to rely on an
authorized service center or Earthquake. A parts breakdown is
located toward the end of this manual.
We will always be glad to answer any questions you have, or
help you nd suitable assistance. To order parts or inquire about
warranty, call or e-mail us using the contact information found
under "Ordering Replacement Parts".
ORDERING REPLACEMENT PARTS
Parts can be obtained directly from the factory. To order parts
visit www.getearthquake.com or call 1-800-345-6007.
For other general questions, you can e-mail us at [email protected]om.
IN CASE OF A SERVICE PROBLEM, DO NOT SEND PRODUCT
BACK TO RETAILER. CONTACT EARTHQUAKE AT 800345
6007.
Include the following information with your order:
1) Part numbers
2) Part description
3) Quantity
4) Model number and serial number
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
14
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE REMEDY/ACTION
Engine will not start 1. Power switch o 1. Flip switch to ON position
2. Spark plug wire disconnected 2. Connect spark plug wire to spark plug
3. Out of fuel 3. Refuel
4. Spark plug wet, faulty or improperly
gapped
4. Clean, replace or gap spark plug
5. Fuel line hose not positioned in bottom of
gas tank
5. Push fuel line down into fuel in gas tank
6. Stale fuel 6. Drain old fuel and replace with fresh. Use fuel stabi-
lizer for future preventative measures.
Engine runs rough, oods during
operation
1. Dirty air lter 1. Clean or replace air lter
2. Choke partially engaged 2. Turn o choke
3. Carburetor out of adjustment 3. Call factory or take to authorized repair center
Engine is hard to start 1. Stale fuel 1. Drain old fuel and replace with fresh. Use gas stabi-
lizer for future preventative measures.
2. Spark plug wire loose 2. Make sure spark wire is securely attached to spark
plug
3. Dirty carburetor 3. Clean carburetor, use gas stabilizer, new gas can, or
purchase carburetor replacement or repair kit per
parts breakdown
4. Carburetor not primed 4. Prime unit 3 more times, squeeze throttle when pull-
ing recoil handle
Engine misses or lacks power 1. Clogged gas tank 1. Remove and clean
2. Clogged air lter 2. Clean or replace
3. Carburetor out of adjustment or bad 3. Call factory or take to authorized repair center
4. Spark plug wet, faulty or improperly gapped 4. Clean, replace or gap spark plug
Engine runs, then quits 1. Gas cap not venting 1. Unscrew the gas cap and then re-tighten gas cap
2. Plugged fuel lter 2. Clean or replace
3. Carburetor out of adjustment or bad 3. Call factory or take to authorized repair center
Engine revs too high 1. Carburetor out of adjustment or air leak in
the intake
1. Call factory or take to authorized repair center
Auger turns at idle 1. Idle speed too high 1. Adjust idle speed lower
2. Broken clutch spring 2. Replace spring
Auger turns, but has no power 1. Choke on 1. Turn o choke after engine is running
2. Carburetor out of adjustment 2. Call factory or take to authorized repair center
3. Broken transmission 3. Call factory or take to authorized repair center
4. Worn clutch shoes 4. Replace clutch shoes and spring
Auger jumps 1. Blade damaged 1. Replace with new blade
Auger cuts slowly 1. Dull blade 1. Replace with new blade
2. Damaged shtail point 2. Replace shtail point
Contact customer service if above remedies fail.
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 15
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
E43 POWERHEAD & AUGER PARTS
KEY # PART NO. DESCRIPTION QT Y.
1 E43CCV ENGINE VIPER 43CC CAT CONV 1
2 14644 THROTTLE CABLE, E43 1
3 4828 HANDLEBAR THREADED 1
4 4822 ASSEMBLY TRIGGER LONG THROW 1
5 4827 BOLT 1024 X 1/2 PPHMS GR5 ZN FT 1
6 8930B BOLT 1/420 X 3/4 HH GR5 BLK ZN 4
7 3004119 TRANSMISSION ASSEMBLY 30:1 E43
S/N 40539
1
8 75300 KIT TOP CASTING 1
9 3004100 CLUTCH DRUM 1
10 8922 BALL BEARING R12 DOUBLE LIP 3
11 9814
THREAD
1
12 8924 SNAP RING 3
13 8915 2
21
19
10, 18
20
18
8, 15, 18
10, 18
12
14
16, 18
17
16, 8
8
10, 8
9
11
12
13
2
1
5
4
3
7
6
KEY # PART NO. DESCRIPTION QT Y.
14 8912 1
15 8919 GASKET 1
16 8923 BALL BEARING R10 2
17 8914 GEAR 48T HARD 1
18 75600 KIT LOWER CASTING 1
19 8913 1
20 8931F BOLT 1/420 X 2 SHCS FT 4
21 8929 BOLT 1/420 X 11/2 SHCS 2
22 9214A GEAR 10T CLUSTER PINION HT 1
23 11468 GREASE EP2 MOLY 1
13
22
12
GREASE
23
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
16
E43 ENGINE PARTS
37
37, 38
37, 41
10
44
11
21
37, 43
37, 42
22
23
49
19
14
13
47
3
1, 2
5
4
6
8
7
1
15
18
45
17
16
36
46
48
39
1, 47
20
47
24
12
9
53
26
25
1, 51
37, 52
28
34
33
35
29
27
30
31
50
40
32
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 17
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
E43 ENGINE PARTS LIST
KEY
NO. PART NO. DESCRIPTION QT Y.
1 11209 FLYWHEEL, MAGNETO 1
2 300337 NUT, FLANGE M8 1
3 300462 WASHER, ROTOR 2
4 300413 CLUTCH ROTOR ASSEMBLY W/SPRING 1
5 300449 WASHER, SPRING 2
6 300450 BOLT, SHOULDER 2
7 300467 PIN, LOCATING 2
8 3004110 MOUNT RING & SHROUD 1
9 300491 RECOIL CLUTCH 1
10 300429 PLATE, RECOIL 1
11 3004121 HANDLE, RECOIL STANDARD 1
12 300430 RECOIL ASSEMBLY WITH STANDARD
HANDLE
1
13 300472 IGNITION COIL 1
13* 300472CE IGNITION COIL CE 1
14 300482 SHROUD, ENGINE 1
15 300493 BOLT, STUD M6 X 62MM 2
16 300475 GASKET, MUFFLER 1
17 4813 MUFFLER 1
18 4812 COVER, MUFFLER 1
19 BM6A SPARK PLUG 1
20 300483 COVER, ENGINE SHROUD 1
21 300476 GASKET, INTAKE 1
22 300478 WINDPIPE, INTAKE 43CC/51CC 1
23 300479 GASKET, CARBURETOR 1
24 300486 CARBURETOR 1
25 300481 ORING, CARBURETOR 1
26 3004109 PRIMER BULB 1
27 3004158 COVER, AIR FILTER 1
28 3004150 AIR FILTER ASSEMBLY 1
29 3004156 FOAM, AIR FILTER 1
30 3004157 PLATE, REINFORCEMENT 1
31 3004150 AIR FILTER ASSEMBLY 1
32 3004150 AIR FILTER ASSEMBLY 2
33 3004150 AIR FILTER ASSEMBLY 1
34 3004150 AIR FILTER ASSEMBLY 1
35 3004150 AIR FILTER ASSEMBLY 1
KEY
NO. PART NO. DESCRIPTION QT Y.
36 56105 BRACKET, GAS TANK 1
37 10683 GAS TANK KIT INCLUDES TANK.
GROMMET, FUEL LINE, FUEL FILTER
AND GAS CAP.
1
38 11936 GAS CAP, MANUAL VENTING 1
39 300332 SHROUD, GAS TANK 1
40 1021 SWITCH, ROCKER 1
41 3004105 KIT FUEL LINE TWO HOLE GROMMET 1
42 3004105 KIT FUEL LINE TWO HOLE GROMMET 1
43 3004105 KIT FUEL LINE TWO HOLE GROMMET 1
44 300335 BOLT W/WASHER PHILLIPS HH 4
45 300492 NUT, FLANGE M6 2
46 300471 BOLT W/WASHER M5 X 12MM 4
47 300439 BOLT W/WASHER PH M5 X 18MM 7
48 300336 BOLT HH M6 X 10MM 2
49 300438 BOLT W/WASHER M5 X 25MM 2
50 300456 BOLT M5 X 50MM 2
51 300338 KEY, FLYWHEEL 1
52 3004103 FILTER, FUEL 1
53 300351 BOLT HH M6 X 8MM 2
- 3004114 KIT, CARBURETOR 1
* For E43CE Only.
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
18
6
8, 9
23
5
10
18
19
14
23
15
11
21
3
22
7
1
4
18
19
5
2
20
16
19
5
4
12
21
3
22
7
1
18
2
20
BALLOON #
PART # DESCRIPTIONQTY.
1 154
EARTH AUGER WELDMENT 10 IN RH
1
2 8980
SHOCK SPRING
1
3
EB10A
BLADE EARTH 10INCH CUT AND SHARPENED
1
4
EBOLT
BOLT 1/4-28 X 5/8 HH GR5 ZN
2
5 1423
BOLT 5/16-18 X 2 HH GR5 ZN
2
6
WF516
WASHER FLAT 5/16 INCH STANDARD ZN
2
7
60G56
NUT-LOC 5/16-18 BI-WAY ZN
2
8
ENUT
NUT-LOC 1/4-28 BI-WAY
2
9
8958HD
FISH TAIL POINT
1
10 1151
DECAL AND ART WARNING AUGER ICE AND EARTH
1
11
I10
INSERT 10 IN AUGER BOX
2
12 1433 BOLT 3/8-16 X 1-1/2 HH 1
13 2104
NUT 3/8-16 HLKBW ZN
1
14
LBB10P
ASSEMBLY BOX UPC STENCIL EA10F
1
7
5
17
19
13
21
2
1
4
20
18
EA6F
EA2F, EA3F EA4F
EA8F EA10F
AUGER PARTS EXPLOSIONS
24
REVISIONS
ECN #
REV.
DESCRIPTION
DATE
BY
8682 1
CREATED PRINT
3/8/2011
MDO
BALLOON #
PART # DESCRIPTION
ASSEMBLED/QTY.
1
553B
WELDMENT 12 INCH EXTENSION
1
2 1433 BOLT 3/8-16 X 1-1/2 HH 1
3 2104
NUT 3/8-16 HBW GR5 ZN
1
PARTS TO BE FREE OF
BURRS AND SHARP EDGES
THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS AND REMAINS THE PROPERTY OF ARDISAM INC.
AND IS CONFIDENTIAL. IT IS SUBMITTED AND MAY BE USED ONLY IN CONNECTION WITH ARDISAMS' PROPOSALS
AND/OR ITS CUSTOMERS' ORDERS. IT SHALL NOT BE DISCLOSED TO OTHERS OR COPIED
WITHOUT ARDISAMS'
SPECIFIC WRITTEN CONSENT AND SHALL BE IMMEDIATELY RETURNED UPON REQUEST.
MATERIAL
NAME
TREATMENT
DR BY APPD PRT NO
EXT12
PT WEIGHT
SURFACE AREA
DATE
REVISION
THIRD ANGLE PROJECTION
SEE BILL OF MATERIALS
NONE
697.20
57969.61
12 INCH EXTENSION
1
MOlsen
MDO 1/19/2011
03/08/2011
SHEET: 1 OF 2
ALL ANGLES ARE DECIMAL DEGREES
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
THREADS CLASS 2
0.0 ± 1.0°
0 ± 2°
ANGLES:
0.000 ± 0.250 MM
0.00 ± 0.75 MM
0.0 ± 2.5 MM
OTHERWISE NOTED:
TOLERANCE UNLESS
EXT12
25
REVISIONS
ECN #
REV.
DESCRIPTION
DATE
BY
8682 1
ISSUED DRAWING
3/8/2011
MDO
BALLOON #
PART # DESCRIPTION
ASSEMBLED/QTY.
1
553C
WELDMENT 18 INCH EXTENSION
1
2 1433 BOLT 3/8-16 X 1-1/2 HH 1
3 2104
NUT 3/8-16 HBW GR5 ZN
1
PARTS TO BE FREE OF
BURRS AND SHARP EDGES
THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS AND REMAINS THE PROPERTY OF ARDISAM INC.
AND IS CONFIDENTIAL. IT IS SUBMITTED AND MAY BE USED ONLY IN CONNECTION WITH ARDISAMS' PROPOSALS
AND/OR ITS CUSTOMERS' ORDERS. IT SHALL NOT BE DISCLOSED TO OTHERS OR COPIED
WITHOUT ARDISAMS'
SPECIFIC WRITTEN CONSENT AND SHALL BE IMMEDIATELY RETURNED UPON REQUEST.
MATERIAL
NAME
TREATMENT
DR BY APPD PRT NO
EXT18
PT WEIGHT
SURFACE AREA
DATE
REVISION
THIRD ANGLE PROJECTION
SEE BILL OF MATERIALS
NONE
1049.56
81683.44
18 INCH EXTENSION
1
MOlsen
MDO 1/20/2011
03/30/2011
SHEET: 1 OF 2
ALL ANGLES ARE DECIMAL DEGREES
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
THREADS CLASS 2
0.0 ± 1.0°
0 ± 2°
ANGLES:
0.000 ± 0.250 MM
0.00 ± 0.75 MM
0.0 ± 2.5 MM
OTHERWISE NOTED:
TOLERANCE UNLESS
EXT18
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 19
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
AUGER PARTS LIST
KEY
NO.
PART
NO. DESCRIPTION QT Y.
1 1423
(auger shock spring)
2
2 1433
(auger to powerhead)
2
3 53684 SHOCK TOP 1PC
earth augers)
1
4 60G56 NUTHEX 2WAY REVERSIBLE LOCK
NUT, 5/1618
2
5 8958HD FISHTAIL POINT
earth auger)
1
6 8970 EARTH POINT
auger)
1
7 8980 SHOCK SPRING Used on 6" and larger
earth augers)
1
8 EA2F 1
9 EA3F 1
10 EA4F 1
11 EA6F 1
12 EA8F 1
13 EA10F
POINT
1
14 EB4 (includes EBOLT &
ENUT)
1
15 EB6 (includes EBOLT &
ENUT)
1
16 EB8 (includes EBOLT &
ENUT)
1
17 EB10 (includes EBOLT
& ENUT)
1
18 EBOLT
(earth blade to auger)
2
19 ENUT NUTNYLOC, 1/428 2
20 2104 NUT HEX LOCKING, 3/816 2
KEY
NO.
PART
NO. DESCRIPTION QT Y.
21 WF516 2
22 715 SET SCREW 1/420 X 1/4 SCPC BLK
OXIDED
2
23 8955 BOLT 3/816 X 11/4 SHCS 1
24 EXT12 DEPTH EXTENSION, 12" 1
25 EXT18 DEPTH EXTENSION, 18" 1
ITEMS NOT SHOWN
EB6HD (in-
cludes EBOLT & ENUT)
1
EB8HD (in-
cludes EBOLT & ENUT)
1
EB
10HD
(includes EBOLT & ENUT)
1
Operator's Manual
E43/E43CE 1-Man Earth Auger Powerhead
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
20
WARRANTY TERMS AND CONDITIONS
PRODUCT WARRANTY: 1YEAR LIMITED WARRANTY
Ardisam, Inc. (Ardisam) warrants the product(s) under a one-year limited warranty to be free from defects in the material or
workmanship or both for a period not exceeding twelve consecutive months from the date of original purchase by the rst retail
consumer or rst commercial end user. “Consumer use“ means personal recreational use by a retail consumer. “Commercial use“
or “commercial application“ means all other uses, including use for commercial, income producing or rental purposes. Once
a product has experienced commercial use, it shall thereafter be considered as a commercial use product for the purpose of
this warranty. This warranty applies to the original owner that provides a proof of purchase. The warranty is not transferable.
The warranty period begins on the date of purchase by the rst retail consumer or commercial end user, and continues for
the twelve month consecutive period thereafter. Any unit used in a commercial application is covered for a period of 90 days
after purchase by the rst commercial end user. For the warranty to be valid, the product must be registered online, or the
warranty card must be lled out and received by Ardisam, within 30 days of purchase. Ardisam shall not be obligated to ship
any repair or replacement product to any location outside of the United States of America or Canada.*
ENGINE WARRANTY: 2-YEAR LIMITED EMISSIONS CONTROL WARRANTY
(SEE EXPLANATION OF EMISSIONS CONTROL WARRANTY STATEMENT FOR DETAILS)
Ardisam warrants the Viper® engine(s) under a two-year limited emissions control warranty to be free from defects in the
materials or workmanship or both for the service life of the product not to exceed twenty-four consecutive months from the
date of purchase for consumer applications. As a Viper® small engine owner, you are responsible to perform periodic main-
tenance as specied in the product’s operator’s manual and/or engine manual. The warranty period begins on the date of
purchase by the rst retail consumer or commercial end user, and continues for the period of time stated above.*
For replacement parts, phone 800-345-6007.
*This warranty policy applies only to products which have not been subjected to negligent use, misuse, uses other than
those indicated in the product’s operator’s manual, alteration, accident, use of unauthorized parts, failure to perform periodic
maintenance as specied in product’s operator’s manual, normal wear and tear, use of unauthorized parts or repairs performed
at unauthorized service centers. There is no other expressed warranty. Implied warranties, including those of merchantability
and tness for a particular purpose, are limited to one year from purchase, or to the extent permitted by law. All other implied
warranties are excluded. Liability for incidental or consequential damages are excluded to the extent exclusion is permitted by
law. Ardisam does not assume, and does not authorize any other person to assume for Ardisam, any liability in connection with
the sale of Ardisam products. To be at “No Charge,” warranty work must be sent directly to and performed by Ardisam or
an Ardisam Authorized Warranty Service Facility. To obtain warranty service and/or replacement instructions, contact the
Ardisam Customer Service Department at 800-345-6007. If you choose to ship your product to Ardisam for warranty repair,
you must rst have prior approval from Ardisam by calling the Ardisam Customer Service Department for a return material
authorization number (RMA#). Under these circumstances, all items must be shipped prepaid. For Viper® engine warranty
repairs, Ardisam will cover the cost of shipping only for purchasers located more than 100 miles from an Ardisam Authorized
Warranty Service Facility if it is determined that warranted repair is indeed necessary. Ardisam will at no charge, repair or
replace, at the discretion of Ardisam, any defective part which satises all conditions stated above. Ardisam retains the right
to change models, specications and price without notice. Ardisam shall not be obligated to ship any repair or replacement
product to any location outside of the United States of America or Canada.
17645-REV1
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
EarthQuake E43 Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: EarthQuake E43 User manual
- español: EarthQuake E43 Manual de usuario
Documents connexes
-
EarthQuake E43™ Earth Auger Powerhead Manuel utilisateur
-
-
-
-
EarthQuake 22777 Manuel utilisateur
-
EarthQuake 9800KC Le manuel du propriétaire
-
-
-
EarthQuake 9800K Manuel utilisateur
-
Autres documents
-
Southland SEA43.1 Manuel utilisateur
-
Powermate PEA438 Manuel utilisateur
-
Eskimo F1 ROCKET Manuel utilisateur
-
-
iON 11733 Manuel utilisateur
-
-
-
-
-