Zanussi ZWH7120 Manuel utilisateur

Marque: Zanussi

Modèle: ZWH7120

Catégorie: Machines à laver

Taper: Manuel utilisateur

User manual 2

Notice d'utilisation 25

Washing Machine

Lave-linge

ZWH 7120

Contents

Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2

Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 4

Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4

Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ 7

Consumption values _ _ _ _ _ _ _ _ _ _ _ _ 10

Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 11

First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12

Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13

Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ 15

What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18

Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20

Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20

Electrical connection _ _ _ _ _ _ _ _ _ _ _ _ 23

Environment concerns _ _ _ _ _ _ _ _ _ _ _ 23

Subject to change without notice.

Safety instructions

Important! Read carefully & keep for future

reference.

• The safety of Your appliance complies with

the industry standards and with legal require-

ments on the safety of appliances. However,

as manufacturers, we feel it is our duty to

provide the following safety notes.

• It is most important that this instruction book

should be retained with the appliance for fu-

ture reference. Should the appliance be sold

or transferred to another owner, or should

you move house and leave the appliance, al-

ways ensure that the book is supplied with

the appliance in order that the new owner

can get to know the functioning of the appli-

ance and the relevant warnings.

• You MUST read them carefully before instal-

ling or using the appliance.

• Before first starting up, check the appliance

for any damage incurred during transport.

Never connect up a damaged appliance . If

parts are damaged, contact the Service Cen-

tre.

• If the appliance is delivered in the winter

months when there are minus temperatures.

Store it at room temperature for 24 hours be-

fore using for the first time.

General safety

• It is dangerous to alter the specifications or

attempt to modify this product in any way.

• During high temperature wash programmes

the door glass may get hot. Do not touch it!

• Make sure that small pets and children do

not climb into the drum. To avoid this, please

check into the drum before using.

• Any objects such as coins, safety pins, nails,

screws, stones or any other hard, sharp ma-

terial can cause extensive damage and must

not be placed into the machine.

• Only use the advised quantities of fabric

softener and detergent. Damage to the fabric

can ensue if you over-fill. Refer to the manu-

facturer’s recommendations of quantities.

• Wash small items such as socks, laces,

washable belts in a washing bag or pillow

case as it is possible for such items to slip

down between the tub and the inner drum.

• Do not use your washing machine to wash

articles with whalebones, material without

hems or torn material.

• Always unplug the appliance and turn off the

water supply after use, cleaning and mainte-

nance.

• Under no circumstances should you attempt

to repair the machine yourself. Repairs car-

ried out by inexperienced people may cause

injury or serious malfunctioning. Contact your

local Service Centre. Always insist on genu-

ine spare parts.

Installation

• This appliance is heavy. Care should be tak-

en when moving it.

• When unpacking the appliance, check that it

is not damaged. If in doubt, do not use it and

contact the Service Centre.

www.zanussi.com

• All packing and transit bolts must be re-

moved before use. Serious damage can oc-

cur to the product and to property if this is

not adhered to. See relevant section in the

user manual.

• After having installed the appliance, check

that it is not standing on the inlet and drain

hose and the worktop is not pressing the

electrical supply cable against the wall.

• If the machine is situated on a carpeted floor,

please adjust the feet in order to allow air to

circulate freely under the appliance.

• Always be sure, that there is no water leak-

age from hoses and their connections after

the installation.

• If the appliance is installed in a location sub-

ject to frost, please read the “dangers of

freezing” chapter.

• Any plumbing work required to install this ap-

pliance should be carried out by a qualified

plumber or competent person.

• Any electrical work required to install this ap-

pliance should be carried out by a certified

Service Centre.

Use

• This appliance is designed for domestic use.

It must not be used for purposes other than

those for which it was designed.

• Only wash fabrics which are designed to be

machine washed. Follow the instructions on

each garment label.

• Do not overload the appliance. See the

Washing Programme Table.

• Before washing, ensure that all pockets are

empty and buttons and zips are fastened.

Avoid washing frayed or torn articles and

treat stains such as paint, ink, rust, and grass

before washing. Underwired bras must NOT

be machine washed.

• Garments which have been in contact with

volatile petroleum products should not be

machine washed. If volatile cleaning fluids

are used, care should be taken to ensure that

the fluid is removed from the garment before

placing in the machine.

• Never pull the power supply cable to remove

the plug from the socket; always take hold of

the plug itself.

• Never use the appliance if the power supply

cable, the control panel, the working surface

or the base are damaged so that the inside

of the washing machine is accessible.

Child safety

• This appliance is not intended for use by per-

son (including children) with reduced physi-

cal sensory or mental capabilities or lack of

experience and knowledge unless they have

been given supervision or instruction con-

cerning use of the appliance by a person re-

sponsible for their safety.

• Children should be supervised to ensure that

they do not play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children -

danger of suffocation! Keep them out of chil-

dren’s reach

• Keep all detergents in a safe place out of

children’s reach.

• Make sure that children or pets do not climb

into the drum. To prevent children and pets

becoming trapped inside the drum this ma-

chine incorporates a special feature.

Door safety button

To activate this de-

vice, rotate the button

(without pressing it)

inside the door clock-

wise until the groove

is horizontal. If neces-

sary use a coin.

To disable this de-

vice and restore the

possibility of closing

the door, rotate the

button counter-clock-

wise until the groove

is vertical.

www.zanussi.com

Product description

Detergent dispenser drawer

Control panel

Door opening handle

Rating Plate

Drain pump

Adjustable feet

Detergent dispenser drawer

Compartment for detergent used for pre-

wash and soak phase or for stain remover used

during the stain action phase (if available). The

prewash and soak detergent is added at the be-

ginning of the wash programme. The stain re-

mover is added during the stain action phase.

Compartment for powder or liquid detergent

used for main wash. If using liquid detergent

pour it just before starting the programme.

Compartment for liquid additives (fabric soft-

ener, starch).

Follow the product manufacturer’s recommendations on quantities to use and do not exceed the

«MAX» mark in the detergent dispenser drawer. Any fabric softener or starching additives must

be poured into the compartment before starting the wash programme.

Control panel

On the following page there is a picture of the control panel. It shows the programme selector

dial as well as the buttons, pilot lights and the display. These are presented by relevant num-

bers on the following pages.

www.zanussi.com

1 2 3 4 5 6 7 8

Programme selector dial

SPIN reduction button

OPTIONS button

PREWASH button

EASY IRON button

EXTRA RINSE button

START/PAUSE button

DELAY START button

DOOR LOCKED pilot light

Display

Programme Selector Dial

It allows you to switch the appliance on/off and/

or to select a programme.

Spin Reduction

By pressing this button you can change the

spin speed of the selected programme.

Available options:

Night Cycle

By selecting this function the machine will not

drain the water of the last rinse and all spinning

phases will be suppressed, so as not to wrinkle

the laundry. This washing cycle is very quiet

and it can be selected at night or in times with

a more economical power rate. On some pro-

grammes the rinses will be performed with

more water. Before opening the door it will be

necessary to empty out the water. To empty out

the water, please read the paragraph «At the

end of the programme».

Rinse hold

By selecting this function the water of the last

rinse is not emptied out to prevent the fabrics

from creasing. Before opening the door it will

be necessary to empty out the water. To empty

out the water, please read the paragraph «At

the end of the programme».

Eco

Only for cottons and synthetic items lightly or

normally soiled at a temperature of 40°C or

higher. The washing time will be prolonged and

the washing temperature will be reduced. You

can use this option if you want to wash normally

soiled laundry and at the same time save ener-

gy.

Super Quick

Short cycle for lightly soiled items or for laundry

which needs only freshening up. We recom-

mend you to reduce the fabrics loading.

Prewash

By selecting this option the machine performs a

prewash cycle before the main wash phase.

The washing time will be prolonged. This option

is recommended for heavily soiled laundry.

Easy Iron

By selecting this option the laundry is gently

washed and spun to avoid any creasing. In this

way ironing is easier. Furthermore the machine

www.zanussi.com

will perform some additional rinses in some

programmes. On cotton programmes the maxi-

mum spin speed is reduced automatically.

Extra Rinse

This appliance is designed to save energy. If it

necessary to rinse the laundry using an extra

quantity of water (extra rinse), select this option.

Some additional rinses will be performed. This

option is recommended for people who are al-

lergic to detergents, and in areas where the

water is very soft.

Start Pause

This button allows you to start or to interrupt

the selected programme.

Delay Start

The programme can be delayed from 30 min -

60 min - 90 min, 2 hours and then by 1 hour up

to a maximum of 20 hours by means of this but-

ton.

Door locked pilot light

The pilot light 9 illuminates when the pro-

gramme starts and indicates if the door can be

opened:

• light on: the door cannot be opened. The

machine in working or has stopped with wa-

ter left in the tub.

• light off: the door can be opened. The pro-

gramme is finished or the water has been

emptied out.

• light flashing: the door is opening

Display (10)

10.1 10.2

The display shows the following information:

10.1: Child safety lock

This device permits you to leave the appliance

unattended during it's functioning.

10.2:

• Duration of the selected programme

After selecting a programme, the duration is

displayed in hours and minutes (for example

). The duration is calculated automati-

cally on the basis of the maximum recom-

mended load for each type of fabric. After the

programme has started, the time remaining is

updated every minute.

• Delayed start

The Selected delay set by pressing the rele-

vant button appears on the display for a few

seconds, then the duration of the selected

programme is displayed again. The delay

time value decreases by one unit every hour

and then, when 1 hour remains, every minute.

• Alarm codes

In the event of operating problems, some

alarm codes can be displayed, for example

(see paragraph «What to do if...»).

• Incorrect option selection

If an option which is not compatible with the

set wash programme is selected, the mes-

sage Err is displayed at the bottom of the

display for a few seconds. The integrated red

light of button 7 starts flashing.

• End of programme

When the programme has finished the flash-

ing zero (

) is displayed. The pilot light 9

and the pilot light of button 7 go out. The

door can be opened.

Child safety lock

This device permits you to leave the appliance

unattended so you do not need to worry that

children might be injured by or cause damage

to the appliance. This function remains enabled

also when the washing machine is not working.

There are two different ways to set this option:

1. Before pressing button 7: it will be impos-

sible to start the machine.

2. After pressing button 7: it will be impossi-

ble to change any other programme or op-

tion.

To enable or disable this option press simulta-

neously for about 6 seconds buttons 5 and 6

until on the display, the icon

appears or dis-

appears.

www.zanussi.com

Acoustic signals

The machine is provided with an acoustic de-

vice, which sounds in the following cases:

• at the end of the cycle

• if there is a fault.

By pressing the 4 and 5 buttons simultaneously

for about 6 seconds, the acoustic signal is de-

activated (except if there is a fault). By pressing

these 2 buttons again, the acoustic signal is re-

activated.

Washing programmes

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

COTTONS

90° - 30°

60°

- 40°

Main wash - Rinses

Spin at the maximum speed

Max. load 7 kg - Reduced load 3.5 kg

White and coloured cotton (normally soiled items).

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

ECO

SUPER QUICK

PREWASH

EASY IRON

EXTRA RINSE

SYNTHETICS

60° - 30°

Main wash - Rinses

Maximum spin speed at 900 rpm

Max. load 3.5 kg - Reduced load 2 kg

Synthetic or mixed fabrics: underwear, coloured gar-

ments, non-shrink shirts, blouses.

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

ECO

SUPER QUICK

PREWASH

EASY IRON

EXTRA RINSE

DELICATES

40° - 30°

Main wash - Rinses

Maximum spin speed 700 rpm

Max. load kg 3.5 - Reduced load kg 2

Delicate fabrics: acrylics, viscose, polyester.

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

SUPER QUICK

PREWASH

EXTRA RINSE

www.zanussi.com

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

HANDWASH

40° - Cold

Main wash - Rinses

Maximum spin speed at 900 rpm

Max. load 2 kg

Special programme for delicate fabrics with «hand wash-

ing» care symbol.

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

WOOL

40°

Main wash - Rinses

Maximum spin speed at 900 rpm

Max. load 2 kg

Washing programme for machine washable wool as well

as for hand washable woollens and delicate fabrics.

Note: A single or bulky item may cause imbalance. If the

appliance doesn’t perform the final spin phase, add more

items, redistribute the load manually and then select the

spinning programme.

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

JEANS

40°

Main wash - Rinses

Maximum spin speed at 1200 rpm

Max. load 3.5 kg

With this programme it is possible to wash items like trou-

sers, shirts or jackets in denim and also jersey realized

with hi-tech materials. (The Extra Rinse option will be acti-

vated automatically).

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

PREWASH

EASY IRON

CURTAINS

40°

Prewash - Main wash - Rinses

Maximum spin speed at 700 rpm

Max. load 2.5 kg

This programme it is possible to wash with an extra water

load. The machine will add automatically a prewash phase

before the main wash to eliminate the dust. (Do not put

any detergent in the prewash compartment).

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

EXTRA RINSE

www.zanussi.com

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

SOAK

30°

Prewash - Soak for about 40 minutes - Stop with water in the tub

Max. load 7 kg

Special programme for heavily soiled laundry. The machine performs a soak at

30°C. At the end of this time the machine will stop automatically with water left in

the tub.

Before starting a new washing phase, it is necessary to empty out the water by:

• Draining only: turn the programme selector dial to Drain programme. (Press

the button 7).

• Draining and spinning: turn the programme selector dial to programme Spin,

reduce the spin speed by pressing the button 2, and then press button 7.

Important! This programme cannot be used for very delicate fabrics as silk or

wool. Pour the detergent for the soak programme into the appropriate compart-

ment. At the end of the soak (after having emptied out the water) you can select

the washing programme (first turn the programme selector dial to

, then to the

programme and press the button 5).

MINI PROGRAMME 30

Main wash - Rinses

Maximum spin speed at 700 rpm

Max. load 3 kg

Quick washing programme for cotton and synthetic items

which are lightly soiled or only need freshening up.

SPIN REDUCTION

RINSE

Rinses

Spin at the maximum speed

Max. load 7 kg

With this programme it is possible to rinse and spin cot-

ton garments which have been washed by hand. The ma-

chine performs 3 rinses, followed by a final long spin. The

spin speed can be reduced.

SPIN REDUCTION

NIGHT CYCLE

RINSE HOLD

EASY IRON

EXTRA RINSE

DRAIN

Draining of water

Max. load 7 kg

For emptying out the water of the last rinse in pro-

grammes with the Rinse Hold option selected.

SPIN

Drain and long spin

Spin at the maximum speed

Max. load 7 kg

Separate spin for hand washed cotton garments and after

programmes with the Rinse Hold option selected. You

can choose the spin speed by pressing the relevant but-

ton to adapt it to the fabrics to be spun.

SPIN REDUCTION

www.zanussi.com

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

= OFF

For cancelling the programme which is running or to switch the machine off .

1) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these

programmes at 40°C and 60° C + the option Eco

set, are respectively the «standard 60° C cotton

programme» and the «standard 40° C cotton programme». They are the most efficient programmes in terms

of combined energy and water consumption for washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the selected pro-

gramme.

2) This option is not active at a temperature lower than 40° C.

3) If you select the Super Quick option by pressing button 3, we recommend that you reduce the maximum

load as indicated. Full loading is possible however with somewhat reduced cleaning results.

4) If using liquid detergents, a programme without PREWASH must be selected.

5) With «Easy Iron» option Max. load 1.5 kg

Consumption values

The data of this table are approximate. Different causes can change the data: the quantity and

type of laundry, the water and ambient temperature.

Programmes Load

(kg)

Energy con-

sumption

(kWh)

Water con-

sumption (litre)

Approximate

programme

duration (mi-

nutes)

Remaining

moisture

(%)

Cottons 60 °C 7 1.3 59 120 53

Cottons 40 °C 7 0.77 60 120 53

Synthetics 40 °C 3.5 0.5 54 80 35

Delicates 40 °C 3.5 0.6 63 65 35

Wool/Hand wash

30 °C

2 0.25 55 60 30

Standard cotton programmes

Standard 60 °C

cotton

7 1.15 61 210 53

Standard 60 °C

cotton

3.5 0.73 47 172 53

Standard 40 °C

cotton

3.5 0.6 48 170 53

1) At the end of spin phase.

www.zanussi.com

Off Mode (W) Left On Mode (W)

0.10 0.98

The information given in the charts above are in compliance with the EU Commission regulation 1015/2010

implementing directive 2009/125/EC.

Helpful hints and tips

Sorting out the laundry

Follow the wash code symbols on each gar-

ment label and the manufacturer’s washing in-

structions. Sort the laundry as follows: whites,

coloureds, synthetics, delicates, woollens.

Temperatures

95° or 90°

for normally soiled white cottons

and linen (e.g. tea cloths, towels,

tablecloths, sheets...)

60°/50°

for normally soiled, colour fast

garments (e.g. shirts, night dres-

ses, pyjamas....) in linen, cotton or

synthetic fibres and for lightly

soiled white cotton (e.g. under-

wear)

40°-30°- Cold

for delicate items (e.g. net cur-

tains), mixed laundry including

synthetic fibres and woollens

bearing the label «pure new wool,

machine washable, non-shrink»

Before loading the laundry

Never wash whites and coloureds together.

Whites may lose their «whiteness» in the wash.

New coloured items may run in the first wash;

they should therefore be washed separately the

first time.

Make sure that no metal objects are left

in the laundry (e.g. hair clips, safety pins,

pins).

Button up pillowcases, close zip fasteners,

hooks and poppers. Tie any belts or long tapes.

Remove persistent stains before washing.

Rub particularly soiled areas with a special de-

tergent or detergent paste.

Treat curtains with special care. Remove hooks

or tie them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

washing programme charts.

General rules:

• Cotton, linen: drum full but not too tightly

packed;

• Synthetics: drum no more than half full;

• Delicate fabrics and woollens: drum no

more than one third full.

Washing a maximum load makes the most effi-

cient use of water and energy.

For heavily soiled laundry, reduce the load size.

Removing stains

Stubborn stains may not be removed by just

water and detergent. It is therefore advisable to

treat them prior to washing.

Blood: treat fresh stains with cold water. For

dried stains, soak overnight in water with a spe-

cial detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and

dab the stain; treat several times.

Dried grease stains: moisten with turpentine,

lay the garment on a soft surface and dab the

stain with the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a

rust removing product used cold. Be careful

with rust stains which are not recent since the

cellulose structure will already have been dam-

aged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well

(whites and fast coloureds only).

Grass: soap lightly and treat with bleach

(whites and fast coloureds only).

Ball point pen and glue: moisten with ace-

tone

, lay the garment on a soft cloth and dab

the stain.

1) do not use acetone on artificial silk

www.zanussi.com

Lipstick: moisten with acetone as above, then

treat stains with methylated spirits. Treat any re-

sidual marks with bleach.

Red wine: soak in water and detergent, rinse

and treat with acetic or citric acid, then rinse.

Treat any residual marks with bleach.

Ink: depending on the type of ink, moisten the

fabric first with acetone

, then with acetic acid;

treat any residual marks on white fabrics with

bleach and then rinse thoroughly.

Tar stains: first treat with stain remover, me-

thylated spirits or benzine, then rub with deter-

gent paste.

Detergents and additives

Good washing results also depend on the

choice of detergent and use of the correct

quantities to avoid waste and protect the envi-

ronment.

Although biodegradable, detergents contain

substances which, in large quantities, can up-

set the delicate balance of nature.

The choice of detergent will depend on the

type of fabric (delicates, woollens, cottons,

etc.), the colour, washing temperature and de-

gree of soiling.

All commonly available washing machine deter-

gents may be used in this appliance:

• powder detergents for all types of fabric

• powder detergents for delicate fabrics (60°C

max) and woollens

• liquid detergents, preferably for low tempera-

ture wash programmes (60°C max) for all

types of fabric, or special for woollens only.

The detergent and any additives must be

placed in the appropriate compartments of the

dispenser drawer before starting the wash pro-

gramme.

If using liquid detergents, a programme with-

out prewash must be selected.

Your appliance incorporates a recirculation sys-

tem which allows an optimal use of the concen-

trated detergent.

Follow the product manufacturer’s recommen-

dations on quantities to use and do not ex-

ceed the «MAX» mark in the detergent

dispenser drawer.

Quantity of detergent to be used

The type and quantity of detergent will depend

on the type of fabric, load size, degree of soiling

and hardness of the water used.

Follow the product manufacturers’ instructions

on quantities to use.

Use less detergent if:

• you are washing a small load

• the laundry is lightly soiled

• large amounts of foam form during washing.

Degrees of water hardness

Water hardness is classified in so-called “de-

grees” of hardness. Information on hardness of

the water in your area can be obtained from the

relevant water supply company, or from your lo-

cal authority. If the water hardness degree is

medium or high we suggest you to add a water

softener following always the manufacturer’s in-

structions. When the degree of hardness is

soft, readjust the quantity of the detergent.

First use

• Ensure that the electrical and water

connections comply with the installation

instructions.

• Remove the polystyrene block and any

material from the drum.

• Pour 2 litres of water into the main wash

compartment

of the detergent draw-

er in order to activate the ECO valve.

Then run a cotton cycle at the highest

temperature without any laundry in the

machine, to remove any manufacturing

residue from the drum and tub. Pour 1/2

a measure of detergent into the main

wash compartment and start the ma-

chine.

www.zanussi.com

Daily use

Load the laundry

Open the door by

carefully pulling the

door handle out-

wards. Place the

laundry in the drum,

one item at a time,

shaking them out as

much as possible.

Close the door.

Make sure that no

laundry stays be-

tween the seal and

the door. There is a

risk of water leakage

or damage to the

laundry.

Measure out the detergent and the fabric

softener

Pull out the dispenser drawer until it stops.

Measure out the amount of detergent re-

quired, pour it into the main wash compart-

ment

or in the appropriate compartment if

the selected programme/option it requires

(see more details in "Detergent dispenser

drawer").

If required, pour fabric softener into the com-

partment marked

(the amount used must

not exceed the «MAX» mark in the drawer).

Close the drawer gently.

Select the required programme by means

of the programme selector dial (1)

Turn the programme selector dial to the re-

quired programme.

The green pilot light of button 7 starts to flash.

The selector dial can be turned either clockwise

or anticlockwise.

Turn the selector dial to position

to reset the

programme/to switch the machine OFF.

At the end of the programme the selector

dial must be turned to position

, to

switch the machine off.

Important! If you turn the programme selector

dial to another programme when the machine is

working, the red pilot light of button 7 will blink

3 times and the messageErr is displayed to

indicate a wrong selection. The machine will

not perform the new selected programme.

Select the spin speed, the Night Cycle or

the Rinse Hold option by pressing button

The washing machine will automatically select

the maximum spin value provided for the pro-

gramme you have chosen. (See "Washing pro-

grammes" for the maximum allowed spin

speed).

Press this button repeatedly to change the spin

speed, if you want your laundry to be spun at a

different speed. The relevant light will light up.

Select the available options by means of

buttons 3, 4, 5 and 6

Depending on the programme, different options

can be combined. These must be selected after

choosing the desired programme and before

starting the programme. When these buttons

are pressed, the corresponding pilot lights illu-

minate. When they are pressed again, the pilot

lights go out. If an incorrect option is selected,

the integrated red pilot light of the button 7

flashes 3 times and the message Err is dis-

played.

For the compatibility among the washing pro-

grammes and the options see chapter «Wash-

ing programmes».

www.zanussi.com

Select the Delay Start by pressing button

Before you start the programme, if you wish to

delay the start, press this button to select the

desired delay.

The selected delay time value will appear on

the display for a few seconds, then the duration

of the programme will appear again.

You must select this option after you have set

the programme and before you start the pro-

gramme.

You can cancel or modify the delay time at any

moment, before you press button 7.

Selecting the delay start :

1. Select the programme and the required

options.

2. Select the delay start by pressing button 8.

3. Press button 7:

- the machine starts its hourly countdown.

- the programme will start after the selec-

ted delay has expired.

Cancelling the Delay Start after having started

the programme:

1. Set the washing machine to PAUSE by

pressing button 7.

2. Press button 8 once. On the display will

appear

3. Press button 7 again to start the pro-

gramme.

Important!

• The selected delay can be changed only af-

ter selecting the washing programme again.

• The door will be locked throughout the delay

time. If you need to open the door, you must

first set the washing machine to PAUSE by

pressing button 7 and wait a few minutes be-

fore opening the door. After you have closed

the door, press the same button again.

Important! The Delay Start cannot be

selected with the draining programme.

Start the programme by pressing button 7

To start the selected programme, press this

button; the corresponding green pilot light

stops blinking.

The pilot light 9 illuminates to indicate that the

appliance starts operating and the door is

locked.

If you have chosen a delayed start, the machine

will begin the countdown.

Important! If an incorrect option is selected,

the message Err is displayed for a few seconds

and the red pilot light of this button blinks 3

times.

Altering an option or a running

programme

It is possible to change some options before

the programme carries them out.

Before you make any change, you must pause

the washing machine by pressing button 7.

Changing a running programme is possible only

by resetting it. Turn the programme selector di-

al to

and then to the new programme posi-

tion. Start the new programme by pressing but-

ton 7 again.

The washing water in the tub will be not emp-

tied out.

Interrupting a programme

Press the button 7 to interrupt a programme

which is running, the corresponding pilot light

starts blinking. Press the button again to re-

start the programme.

Cancelling a programme

Turn the selector dial to

to cancel a pro-

gramme which is running. Now you can select a

new programme.

Opening the door after the programme

has started

First set the machine to pause by pressing the

button 7.

If the pilot light 9 blinks and after a few minutes

goes off, the door can be opened.

If the pilot light 9 remains lit, this means that the

machine is already heating or that the water lev-

el is too high. In any case, do not try to force

the door open!

If you cannot open the door but you need to

open it, you have to switch the machine off by

turning the selector dial to

. After a few mi-

nutes the door can be opened.

www.zanussi.com

(Pay attention to the water level and tem-

perature!).

After closing the door, it is necessary to select

the programme and options again and to press

button 7.

At the end of the programme

The machine stops automatically. The blinking

appears on the display, the pilot light of but-

ton 7 and the pilot light 9 go off.

If a programme or an option that ends with wa-

ter left in the tub has been selected, the pilot

light 9 remains on and the door is locked to in-

dicate that the water must be emptied out be-

fore opening the door.

Before you empty out the water, the drum con-

tinues to run at regular intervals until the water

draining.

Follow the below instructions to empty out the

water:

Turn the programme selector dial to

2. Select the draining or spinning programme.

3. Reduce the spin speed if needed, by

pressing the relevant button.

4. Press button 7.

At the end of the programme, the door is re-

leased and can be opened. Turn the pro-

gramme selector dial to

to switch the ma-

chine off.

Remove the laundry from the drum and carefully

check that the drum is empty. If you do not in-

tend to carry out another wash, close the water

tap. Leave the door open to prevent the forma-

tion of mildew and unpleasant smells.

Stand by : once the programme has finished

after a few minutes the energy saving system

will be enabled. The brightness of the display is

reduced. By pressing any button the appliance

will come out of the energy saving status.

Care and cleaning

Warning! You must DISCONNECT the

appliance from the electricity supply,

before you can carry out any cleaning or

maintenance work.

Descaling

The water we use normally contains lime. It is a

good idea to periodically use a water softening

powder in the machine. Do this separately from

any laundry washing, and according to the soft-

ening powder manufacturer's instructions. This

will help to prevent the formation of lime depos-

its.

External cleaning

Clean the exterior cabinet of the appliance with

soap and water only, and then dry thoroughly.

Cleaning the dispenser drawer

The washing powder and additive dispenser

drawer should be cleaned regularly.

Remove the drawer

by pressing the catch

downwards and by

pulling it out. Flush it

out under a tap, to re-

move any traces of

accumulated powder.

To aid cleaning, the

top part of the addi-

tive compartment

should be removed.

www.zanussi.com

Cleaning the drawer recess

Having removed the

drawer, use a small

brush to clean the re-

cess, ensuring that all

washing powder resi-

due is removed from

the upper and lower

part of the recess.

Replace the drawer and run the rinse pro-

gramme without any clothes in the drum.

Cleaning the pump

The pump should be inspected regularly and

particularly if:

• The appliance does not empty and/or spin.

• The appliance makes an unusual noise dur-

ing draining due to objects such as safety

pins, coins etc. blocking the pump.

• A problem with water draining is detected

(see chapter “What to do if...” for more de-

tails).

Warning! Before opening the pump door,

switch the appliance off and remove the

mains plug from the socket.

Proceed as follows:

• Unplug the appliance.

• If it is necessary, wait until the water has

cooled down.

Open the pump door.

Place a container

close to the pump .

Unscrew carefully the

drain filter to drain out

the water.

When no more water comes out, remove the

filter. If necessary, use pliers.

Always keep a rag nearby to dry up any water

spillage when removing the filter.

Clean the filter under a tap, to remove any

traces of fluff.

Remove foreign bod-

ies and fluff from the

pump impeller.

Check carefully whether the pump impeller

rotates (it rotates jerkily). If it doesn’t rotate,

please contact the Service.

Replace the filter into

the pump by inserting

it correctly into the

special guides.

Screw firmly the filter.

Close the pump door.

www.zanussi.com

Caution! When the appliance is in use

and depending on the programme

selected there can be hot water in the pump.

Never remove the filter during a wash cycle.

Always wait until the appliance has finished the

cycle, and is empty.

When refitting the filter, ensure it is securely re-

tightened so as to stop leaks and young

children being able to remove it.

Cleaning the water inlet filters

If the appliance doesn't fill, takes long to fill

with water, the starting button blinks red or

the display (if available) shows the relevant

alarm (see chapter "What to do if..." for more

details), check if the water inlet filters are

blocked .

To clean the water inlet filters:

• Turn off the water

tap.

• Unscrew the hose

from the tap.

• Clean the filter in

the hose with a stiff

brush.

• Screw the hose back onto the tap. Make

sure the connection is tight.

• Unscrew the hose

from the machine.

Keep a rag nearby

because some wa-

ter may flow.

• Clean the filter in

the valve with a

stiff brush or with

the piece of cloth.

35°

45°

• Screw the hose back to the machine and

make sure the connection is tight.

• Turn on the water tap.

Frost precautions

If the machine is installed in a place where the

temperature could drop below 0°C, remove the

remaining water from the inlet hose and the

drain pump.

1. disconnect the mains plug from the mains

socket.

2. close the water tap

3. unscrew the water inlet hose from the tap;

4. put the two ends of the inlet hose in a con-

tainer and let the water flow out of the

hose.

5. empty the drain pump as described in the

‘Emergency emptying out’ section.

6. when the drain pump is empty, install the

water inlet hose again.

Warning!

Make sure that the temperature is more than 0

°C before you use the appliance again.

The manufacturer is not responsible for dam-

ages caused by low temperatures.

Emergency emptying out

If the water is not discharged, proceed as fol-

lows to empty out the machine:

1. Pull out the plug from the power socket.

2. Close the water tap.

3. If necessary, wait until the water has

cooled down.

4. Open the pump door.

5. Place a bowl on the floor.

6. Unscrew carefully the filter. When the bowl

is full, screw the filter again.

– The water drain out by gravity into the

bowl.

– Empty the bowl.

– Repeat the procedure until water stops

flowing out.

7. Clean the pump if necessary as previously

described.

www.zanussi.com

8. Screw firmly the filter again and close the

door pump.

Important! Every time you drain the water

through the emergency emptying hose you

must pour 2 litres of water into the main wash

compartment of the detergent drawer and then

run the drain programme. This will activate the

ECO Valve device avoiding that part of the

detergent remains unused at next washing.

What to do if…

Certain problems are due to lack of simple

maintenance or oversights, which can be

solved easily without calling out an engineer.

Before contacting your local Service Centre,

please carry out the checks listed below.

During machine operation it is possible that the

red pilot light of button 7 blinks, one of the fol-

lowing alarm codes appears on the display and

some acoustic signals sound every 20 seconds

to indicate that the machine is not working:

•

: problem with the water supply.

•

: problem with the water draining.

•

: door open.

Once the problem has been eliminated, press

the button 7 to restart the programme. If after

all checks, the problem persists, contact your

local Service Centre.

Problem Possible cause/Solution

The machine does not start:

The door has not been closed.

• Close the door firmly.

The plug is not properly inserted in the power socket.

• Insert the plug into the power socket.

There is no power at the socket.

• Please check your domestic electrical installation.

The main fuse has blown.

• Replace the fuse.

The selector dial is not correctly positioned and the button 7 has not

been pressed.

• Please turn the selector dial and press the button 7 again.

The delay start has been selected.

• If the laundry are to be washed immediately, cancel the delay start.

The Child Safety Lock has been activated.

• Deactivate the Child Safety Lock.

The machine does not fill:

The water tap is closed.

• Open the water tap.

The inlet hose is squashed or kinked.

• Check the inlet hose connection.

The filter in the inlet hose or the inlet valve filter are blocked.

• Clean the water inlet filters. (See "Cleaning the water inlet filters" for

more details).

The door is not properly closed.

• Close the door firmly.

www.zanussi.com

Problem Possible cause/Solution

The machine does not empty

and/or does not spin:

The drain hose is squashed or kinked.

• Check the drain hose connection.

The drain filter is clogged.

• Clean the drain filter.

An option or a programme that ends with the water still in the tub or a

that eliminates all the spinning phases has been selected.

• Select the draining or spinning programme.

The laundry is not evenly distributed in the drum.

• Redistribute the laundry.

There is water on the floor:

Too much detergent or unsuitable detergent (creates too much foam)

has been used.

• Reduce the detergent quantity or use another one.

Check whether there are any leaks from one of the inlet hose fittings. It is

not always easy to see this as the water runs down the hose; check to

see if it is damp.

• Check the water inlet hose connection.

The drain or inlet hose is damaged.

• Replace it with a new one.

The filter of the drain pump has not been properly screwed in after

cleaning action.

• Screw the filter fully in.

Unsatisfactory washing re-

sults:

Too little detergent or unsuitable detergent has been used.

• Increase the detergent quantity or use another one.

Stubborn stains have not been treated prior to washing.

• Use commercial products to treat the stubborn stains.

The correct temperature was not selected.

• Check if you have selected the correct temperature.

Excessive laundry load.

• Reduce the laundry load.

The door will not open:

The programme is still running.

• Wait the end of washing cycle.

The door lock has not been released.

• Wait until the pilot light 9 goes off.

There is water in the drum.

• Select drain or spin programme to empty out the water.

The machine vibrates is

noisy:

The transit bolts and packing have not been removed.

• Check the correct installation of the appliance.

The support feet have not been adjusted

• Check the correct levelling of the appliance.

The laundry is not evenly distributed in the drum.

• Redistribute the laundry.

Maybe there is very little laundry in the drum.

• Load more laundry.

www.zanussi.com

Problem Possible cause/Solution

Spinning starts late or the

machine does not spin:

The electronic unbalance detection device has cut in because the laun-

dry is not evenly distributed in the drum. The laundry is redistributed by

reverse rotation of the drum. This may happen several times before the

unbalance disappears and normal spinning can resume. If, after 10 mi-

nutes, the laundry is still not evenly distributed in the drum, the machine

will not spin. In this case, redistribute the load manually and select the

spin programme.

• Redistribute the laundry.

The load is too small.

• Add more items, redistribute the load manually and then select the

spinning programme.

The machine makes an un-

usual noise:

The machine is fitted with a type of motor which makes an unusual noise

compared with other traditional motors. This new motor ensures a softer

start and more even distribution of the laundry in the drum when spin-

ning, as well as increased stability of the machine.

No water is visible in the

drum:

Machines based on modern technology operate very economically using

very little water without affecting performance.

If you are unable to identify or solve the prob-

lem, contact our service centre. Before tele-

phoning, make a note of the model, serial num-

ber and purchase date of your machine: the

Service Centre will require this information.

Mod. ... ... ...

Prod. No. ... ... ...

Ser. No. ... ... ...

. ..

...

Prod. N

...

.. ..

r. No

... ... ...

Technical data

Dimensions Width

Height

Depth

Depth (Overall dimensions)

60 cm

85 cm

55.3 cm

64.2 cm

Electrical connection

Voltage - Overall power - Fuse

Information on the electrical connection is given on the rating plate, on

the inner edge of the appliance door.

Water supply pressure Minimum

Maximum

0,05 MPa

0,8 MPa

Maximum Load Cotton 7 kg

Spin Speed Maximum 1000 rpm

Installation

Unpacking

Caution! All transit bolts and packing

must be removed before using the

appliance.

www.zanussi.com

La page charge ...

Zanussi ZWH7120 Manuel utilisateur

Marque: Zanussi

Modèle: ZWH7120

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZWH7120 User manual

Zanussi ZWH7120 Manuel utilisateur

Zanussi ZWH7120 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents