Camp Chef PGVXXL Mode d'emploi

Marque: Camp Chef

Modèle: PGVXXL

Taper: Mode d'emploi

Ce manuel convient également à

PGVXXLC

PELLET SMOKER

WARNING & INSTRUCTION BOOKLET

MODEL PGVXXL

www.CampChef.com | 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

WARNING

FOR OUTDOOR USE ONLY

WARNING

If the information in this manual is not

followed exactly, a ﬁre or explosion may

result causing property damage, personal

injury or loss of life.

WARNING

• To installer or person assembling this

appliance: Leave this manual with this

appliance for future reference.

• To consumer: Keep this manual with this

appliance for future reference.

This instruction manual contains important

information necessary for the proper assembly

and safe use of this product. Read and

follow all warnings and instructions before

assembling and using this appliance. Do not

discard this instruction manual.

CAUTION

Use Only Wood Pellet Fuel Speciﬁed By The

Manufacturer. Do Not Use Pellet Fuel Labeled As

Having Additives. Only use Camp Chef Premium

Pellets with the following speciﬁcations. 8,000-

8,300 BTU/LB 0.75-0.85% Ash content

CAUTION

Contact local building or ﬁre ofﬁcials about

restrictions and installation inspection

requirements in your area.

A MAJOR CAUSE OF FIRES IS FAILURE TO

MAINTAIN REQUIRED CLEARANCES (AIR

SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF

UTMOST IMPORTANCE THAT THIS PRODUCT BE

INSTALLED ONLY IN ACCORDANCE WITH THESE

INSTRUCTIONS.

DANGER

• Never operate this appliance unattended.

• Never operate this appliance within 10 ft (3

m) of any structure, combustible material or

other gas cylinder.

• Never operate this appliance within 25 ft (7.5

m) of any ﬂammable liquid.

• Heated liquids remain at scalding

temperatures long after the cooking process.

Never touch cooking appliance until liquids

have cooled to 115°F (45°C) or less.

Failure to follow these instructions could result

in ﬁre, explosion or burn hazard which could

cause property damage, personal injury or

death.

CAUTION

Always store wood pellets away from heat

producing appliances and other food containers.

Pellets should be stored in a dry environment.

WARNING

Normal use will create a buildup of ash, grease,

and creosote inside the smoker. The smoker must

be thoroughly cleaned after every 50 hours of use

or if a buildup of grease or creosote is noticed

inside the smoker. Clean the smoker by removing

all internal parts and thoroughly scrape away all

grease and creosote from all internal surfaces

including the grease drain and remove debris from

the smoker. The drip tray must always be cleaned

prior to turning the smoker to high. Excessive

buildup of grease and creosote may result in a

grease ﬁre. If a grease ﬁre does occur, turn off

the smoker using the main power switch and

close the door. Leave the door closed until the ﬁre

extinguishes itself. If an uncontrolled ﬁre does

occur, immediately call the local ﬁre department.

Never put water on a grease ﬁre.

CARBON MONOXIDE WARNING

Follow these guidelines to prevent this colorless, odorless gas from poisoning you, your family or others. Know the

symptoms of carbon monoxide poisoning: headache, dizziness, weakness, nausea, vomiting, sleepiness, and confusion.

Carbon monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in loss of consciousness

and death. See a doctor if you or others develop cold or ﬂu-like symptoms while cooking or in the vicinity of this

appliance. Carbon monoxide poisoning, which can easily be mistaken for a cold or ﬂu, is often detected too late. Alcohol

consumption and drug use increase the effects of carbon monoxide poisoning. Carbon monoxide is especially toxic to

mother and child during pregnancy, infants, the elderly, smokers and people with blood or circulatory system problems,

such as anemia, or heart disease.

0918 PGVXXL PARTS

PGVXXL PARTS

Hardware Bags:

PGXXL-13

Legs & Hopper Hardware

Qty (16) M6 x 15 Bolts

Qty (2) M4 Self Tapping Screws

PGXXL-10

Wire Rail Hardware

Qty (8) M6 x 20 bolts

Qty (8) M6 Flat Washer

Qty (8) M6 keps Nut

PGXXL-11

Heat Deflector Bracket Hardware

Qty (4) M4 X 10 Screws

PGXXL-12

Probe Cover & Thermometer Hardware

Qty (4) #8-32 Self Tapping Screws

PG24-9 (1)

PULLOUT KNOB

PG24-42 (1)

PULLOUT LOCK

PG24-41 (1)

BURNER PULLOUT

PG24-17 (1)

ASH CUP

PG24-34 (1)

FEED GASKET

PG24-44 (1)

THERMOMETER

PG24-54 (2)

PROBE COVER

PG24-4 (1)

HEAT DEFLECTOR

SMV-45 (3)

JERKY/SEAFOOD RACK

SMV-38 (4)

COOKING GRID

SMV-3 (1)

DAMPER VENT

SMV-40 (1)

SMV WIRE HANDLE

SSG24 (1)

SAUSAGE RACK

PGXXL-17 (1)

HANDLE ASM

PG36-7 (4)

SWIVEL CASTER

PGXXL-1

DRIP TRAY

PGXXL-2 (2)

WIRE RAIL

PGXXL-3 (1)

PROBE COVER

PGXXL-16 (1)

HOPPER ASM

PGXXL-5

(1)DOOR

PANEL

PGXXL-6 (1)

BOTTOM DOOR PANEL

PGXXL-7 (2)

HEAT DEFLECTOR BRACKET

PGXXL-8 (4)

LEG

PG24-11 (1)

GREASE BUCKET

M5 SHOULDER SCREW

PGXXL-15 (2)

DOOR HINGE

0918 PGXXL PARTS

PG24-28 (2)

MEAT PROBE

PG24-46 (1)

GUARD PLATE

PG24-45 (1)

CONTROLLER GASKET

M4.2 X 10 SCREW (2)

PG24-30 (1)

CONTROLLER KNOB

PGXXL-9 (1)

CONTROLLER

PG24-9 (1)

PULLOUT KNOB

PG24-42 (1)

PULLOUT LOCK

PGC24-13 (1)

HOPPER CLEANOUT

M6 X 15 BOLT(2)

M6 NUT (2)

PG24-48 (1)

POWER CORD

PGC24-18 (1)

LID MAGNET

PG24-53 (1)

AUGER GUARD

PG24-52 (1)

HOPPER RAKE

PG24-60 (1)

HOPPER LID

PGC24-14 (1)

HOPPER WINDOW

BTOP-1 (1)

BOTTLE OPENER

PGC24-12 (1)

HOPPER HANDLE

M4 X 10 SCREW (2)

PG24-49 (1)

AUGER IMPELLER

PG24-24 (1)

AUGER MOTOR WITH IMPELLER

PG24-23 (1)

AUGER BUSHING

PG24-25

(1)AUGER PIN W

/NUT

PGC24-8 (1)

AUGER

PG24-27 (1)

BLOWER IMPELLER

M4.2 X 10 SCREW (4)

PG24-26 (1)

BLOWER MOTOR WITH IMPELLER

PG24-21 (1)

HEATING ROD

PG24-20 (1)

BURNER

M4.2 X 10 SCREW (4)

1. Do NOT leave this appliance unattended while in use.

The user must remain in the immediate area of the

product and have a clear view of the product at all times

during operation.

2. Keep children and pets away from burner at all times.

3. The use of alcohol, prescription or non-prescription drugs

may impair your ability to properly assemble or safely

operate

this appliance.

4. For OUTDOOR use only. Do NOT use in a building,

garage or any other enclosed area. Do NOT use in or on

recreational vehicles or boats. NEVER use this appliance

as a heater.

5. Do not operate appliance under ANY overhead

construction. Keep a minimum clearance of 18 inches

(0.5 m) from the sides, front and back of appliance to

ANY construction. Keep the area clear of all combustible

material and flammable liquids, including wood, dry

plants and grass, brush, paper, and canvas.

6. This product is not intended for commercial use.

7. Always allow the appliance to cool before covering with

the patio cover.

8. Always cover the appliance, with patio cover (if

supplied), when not in use.

9. Always unplug smoker before installing patio cover.

10. Use only on a level, stable non-combustible surface like

bricks, concrete or dirt. Do not use this appliance on

any surface that will burn or melt like wood, asphalt,

vinyl or plastic.

11. Make sure the grease bucket is in place before starting

the smoker.

12. In the event of a fire the dial should be turned to

shutdown, close the door, and leave it closed until the

fire goes out. After allowing the smoker to cool, follow

the cleaning instructions before the next use.

13. Use only food grade hardwood pellets manufactured for

use in pellet smokers. Using softwood or heating pellets

will void your warranty.

14. Do not allow the hopper to run out of pellets. Pellets

can be added at any time. The hopper will hold

approximately 15 pounds of pellets. The pellet usage

will vary greatly depending on the ambient temperature

as well as

cooking temperature.

15. It is recommended that you not store pellets in the

hopper for extended periods as they may absorb

moisture from the air and clog the auger.

16. Keep the door closed during cooking. The smoker is

designed to cook with the door closed.

17. Do not use accessories not specified for use with

appliance.

18. Never use gasoline, gasoline-type lantern fuel,

kerosene, charcoal lighter fluid, or similar liquids to

start or freshen up a fire in this appliance. Keep all

such liquids well away from the appliance when in use.

19. Ashes should be placed in a metal container with a

tight fitting door. The closed container of ashes should

be placed on a non combustible floor or on the ground,

well away from all combustible materials, pending final

disposal. When the ashes are disposed by burial in soil

or otherwise locally dispersed they should be retained

in the closed container until all cinders have thoroughly

cooled.

20. Creosote – Formation and need for removal. When wood

pellets are burned slowly, they produce tar and other

organic vapors that combine with expelled moisture

to form creosote. The creosote vapors condense in a

relatively cool oven flue and exhaust hood of a slow

burning fire. As a result, creosote residue accumulates

on the walls of the smoker. When ignited, this creosote

makes an extremely hot fire. The smoker should be

inspected every 50 hours to determine when grease

and/or creosote build-up has occurred. When grease

or creosote has accumulated, it should be removed to

reduce risk of fire.

DANGER

Do not work on this smoker if it is plugged in. Electric

shock may occur resulting in death or serious injury.

Assembly Instructions

Assembly requires two people.

Remove all loose parts from the inside of the smoker and

hopper. Lay a blanket or piece of cardboard down to protect

the smoker.

1. With the smoker cabinet in the upright position remove

the door by lifting it from the hinges. Set the door panel

aside. This will make assembly much easier.

2. Set the smoker assembly on its back. Set the smoker

cabinet on a padded surface such as cardboard or carpet

to prevent scratching or damaging the smoker.

3. Assemble Qty (4) Legs as shown using Qty (12) M6 x 15

bolts. See FIG. 1

M6 x 15

FIG. 1

4. Install stop lock using Qty (2) M6 Shoulder bolts and QTY

(2) M6 nuts. See FIG. 2

FIG. 2

4. Install Stop Lock using Qty (2) M6 Shoulder Bolts and

Qty (2) M6 nuts.

5. Install Burner Pullout by sliding it through the

side where the Stop Lock was installed.

6. Install Stop Lock Bushing on the Burner Pullout.

Then install the Pull Knob on the Burner Pullout.

screws.

Stop Lock

M6 Shoulder Bolt

M6 Nut

5. Install burner pullout by sliding it through the side where

the stop lock was installed. See FIG. 3

SCALE 0.100

Burner Pullout

FIG.3

6. Install stop lock bushing on the burner pullout, then

install the pull knob on the burner pullout. See FIG. 4

FIG. 4

SCALE 0.100

7. Install Qty (2) heat deﬂector brackets using QTY(8) M4 x

10 screws. See FIG. 5

M4 x 10

Heat Deflector

Bracket

FIG. 5

8. Install bottle opener as shown in Fig. 6.

FIG. 6

M6 X 15MM SCREW

BOTTLE OPENER

M6 LOCK WASHER (2)

M6 FLAT WASHER (2)

HOPPER HANDLE (1)

PGC24-12

M6 RUBBER WASHER (2)

9. Install hopper handle as shown in Fig. 7.

M6 X 15MM SCREW

BOTTLE OPENER

M6 LOCK WASHER (2)

M6 FLAT WASHER (2)

HOPPER HANDLE (1)

PGC24-12

M6 RUBBER WASHER (2)

FIG. 7

8. Install the feed gasket over the hopper tube. Install the

hopper tube through the square opening on the side of

the smoker assembly. When the hopper tube is about

half way in, route the Thermometer through the upper

rectangular hole. Note: Be careful not to damage the

thermometer. See FIG. 8

Thermometer

Feed Gasket

Hopper Tube

Route thermometer

through this hole

FIG. 8

9. Attach hopper assembly using Qty (4) M6 x 15 bolts as

shown. See FIG. 9

10. Install thermometer as shown then secure using Qty (2)

#8-32 screws. See FIG. 9

11. Push extra wire from thermometer back through the hole

to the hopper. Install probe cover to the wall where the

thermometer came thru the wall using QTY (2) #8-32

screws. Make sure that the notch in the cover is up and

wire goes through notch so it is not pinched. See FIG. 9

12. Secure hopper end to the smoker body assembly using

Qty (2) self tapping screws. See FIG. 9

Probe Cover

Notch Up

Self Tapping

Screws

Thermometer

#8-32

M6 x 15

Hopper End

FIG. 9

13. Install hopper lid as shown in Fig. 10.

FIG. 10

14. Install Qty (2) probe covers as shown. See FIG. 11

13. Install Qty (2) Probe Covers as shown.

14. Install Qty (2) Wire Rails as shown.

M6 X 15 Bolt

M6 Flat Washer

Probe Cover

M6 Flat Washer

M6 Lock Washer

M6 Hex Nut

M6 X 20 Bolt

M6 Flat Washer

M6 Keps Nut

Wire Rail

FIG. 11

15. Install Qty (2) wire rails as shown. See FIG. 12

13. Install Qty (2) Probe Covers as shown.

14. Install Qty (2) Wire Rails as shown.

M6 X 15 Bolt

M6 Flat Washer

Probe Cover

M6 Flat Washer

M6 Lock Washer

M6 Hex Nut

M6 X 20 Bolt

M6 Flat Washer

M6 Keps Nut

Wire Rail

FIG. 12

16. Install the damper vent on the side of the smoker

assembly using Qty (1) M6 shoulder bolt. See FIG. 13

17. Install SMV wire handle by using Qty (2) M6 x 15 bolts.

See FIG. 13

15. Install the Damper Vent on the side of the smoker assembly

using Qty (1) M6 Shoulder Bolt.

16. Install SMV Wire Handle by using Qty (2) M6 x 15 bolts.

Damper Vent

M6 Sholder Bolt

SMV Wire Handle

M6 x 15 Bolt

FIG. 13

18. Install heat deﬂector on the heat deﬂector bracket.

See FIG. 14

19. Install drip tray. See FIG. 14

17. Install Heat Deflector on the Heat Deflector Bracket.

18. Install Drip Tray.

Drip Tray

Heat Deflector

FIG. 14

20. Install racks in the smoker assembly. See FIG. 15

21. Re-mount the door panel by sliding the door’s hinge pins

into the cabinet’s hinge seats.

See FIG. 15

22. Assemble the door handle as shown using the handle,

Qty (2) wave washers, and Qty (2) M12 lock nuts. See

FIG. 15.

Ash Cup

Grease Bucket

Door Handle

Wave Washer (1)

Door Lock

M12 Lock Nut (2)

FIG. 15

23. Tighten handle nut until the latch barely clears the door

ﬂange. If nut is overtightened handle will be difﬁcult to

rotate. In this case loosen nut 1/4 turn maximum. See

Fig. 16.

FIG. 16

.025 MAX GAP

24. Install grease bucket. See FIG. 17

25. Install ash cup. See FIG. 17

Ash Cup

Grease Bucket

Door Handle

Wave Washer (1)

Door Lock

M12 Lock Nut (2)

FIG. 17

Burner Clean-out

Before each use the burner should be cleaned out by lifting

the pullout lock and pulling the clean-out port knob on the

right side of the smoker to open the burner clean-out. This

will allow the ash from previous use to fall into the cup

under the smoker. The cup should be removed and emptied

and then reinstalled before each use.

After cleaning out the burner make sure to close the burner

clean-out by pushing the clean-out port knob in on the

right side of the smoker. Make sure to lift the pullout lock

and push the clean-out port knob all the way in and lock in

place with the pullout lock. Every 50 hours of use, remove

the smoker grates, grease tray, and heat deﬂector and clean

the inside of the smoker. If you notice a lot of ash blowing

around in the smoker it is time to vacuum it out.

DANGER

Never Operate the Pellet smoker without the ash cup in place.

Make sure the burner clean-out port is closed and locked

before starting the smoker.

Never open the burner clean-out port when the smoker is hot.

Filling the Auger Tube

Caution: Only use the feed setting when the hopper has

ran out of pellets. Feed setting is not for normal use.

The ﬁrst time you use your smoker or any time the hopper

has ran out of pellets you will need to ﬁll the auger tube.

This simply means you must ﬁll the auger tube with pellets

until pellets reach the burner. This is done by turning the

dial to the FEED position then holding the BYPASS button

for 3 seconds. The auger will remain on for no more than

7 minutes. This is ample time for the pellets to reach the

burner. It is easiest to open the burner clean-out by pulling

the knob on the right side of the smoker. Once you hear

pellets dropping into the cup you can close the clean-out

port by pushing the knob on the right side of the smoker and

then select your cooking temperature. (Never operate smoker

without the ash cup in place). Always make sure the burner

clean-out port is closed by pushing in the knob on the right side

of the smoker before selecting any of the cook settings. Never

open the burner clean-out port when the smoker is hot.

Controller Explanation

Power Switch

Used to turn the main power onto the pellet smoker. The fan

will be on whenever the power switch is on. The dial must

be rotated to any of the other positions before the smoker

will start. If the power is turned on with the dial in any other

position than Shutdown the smoker will immediately start

that function. “O” is Off. “-“ is On. See Fig 18

Fig. 18

Dial Positions

Shutdown -This setting must be used after each use. Turn

the dial to this setting and the fan will remain on. Wait for

10 minutes to allow the smoker to ﬁnish burning any pellets

in the burner before turning the main power switch off. This

setting will burn up any extra pellets in the burner and cool

down the smoker. Do not turn the main power switch off

when the smoker is hot.

Low Smoke - This setting is used for smoking foods at an

average temperature of 160F. This setting will produce large

amounts of smoke.

High Smoke - This setting is used for smoking foods at an

average temperature of 220F. This setting will produce large

amounts of smoke.

150F to 350F - There are 25F increment settings from 150F

to 350F. You can simply select any temperature you want

and the smoker will control the temperature within 15F of

the selected temperature.

High - This setting can be used to achieve temperatures up

to 350F depending on ambient temperatures.

Feed - This setting is used to feed pellets to the hopper.

It will be used the ﬁrst time you use the smoker to ﬁll the

auger tube and any time you may inadvertently run the

hopper out of pellets. See instructions on ﬁlling the auger

tube.

Display

“START” - The digital readout will display “START” each

time the dial is changed from the OFF, SHUTDOWN, or FEED

settings to any of the cook settings. The startup cycle

is approximately 8 minutes. During the cook cycle after

the start sequence the digital readout will display the

temperature inside of the smoker. If the Probe Temp button

has been pressed then it will display the temperature of the

external probe used for measuring meat temperatures.

“SDOWN” - The digital readout will display “SDOWN” when

the dial is turned to the shutdown mode. After 10 minutes

the digital readout and the fan will turn off.

“SENSR” - The digital readout will display “SENSR” if there

is an error with the temperature sensor inside of the smoker.

“PRERR” - The digital readout will display “PRERR” when

the Probe Temp button is pressed if either the external probe

is not plugged in or there is a problem with the probe.

“FEED” - The digital readout will display “FEED” if dial is

turned to the feed mode. After 7 minutes the auger will turn

off.

“BPASS” - The digital readout will display “BPASS” when

the bypass button is pressed and held in for 3 seconds. See

the setting on Bypass Mode.

“Flame” - The digital readout will display “ﬂame” if the ﬁre

is extinguished.

Breaking In the Smoker

We suggest turning the smoker to 300F for ½ hour before

cooking on the smoker for the ﬁrst time. This will burn off

any manufacturing oils and cure the paint. Make sure to

follow the instructions for ﬁlling the auger tube before

breaking in the smoker.

DANGER

Always start the smoker with the door open. The door

must be closed after the start cycle.

Cooking

Once the auger tube has been properly ﬁlled you can begin

cooking by selecting any of the cooking temperatures. The

smoker has 13 cook settings. Low Smoke, High Smoke,

150, 200, 225, 250, 275, 300, 325, 350. By selecting any of

these the smoker will go into the Startup mode. The digital

readout will display “START” for 8 minutes during the

startup cycle. After the 8 minutes the digital readout will

display the internal temperature of the smoker. The dial can

be changed at any time during the startup cycle or the cook

cycle between any of the 13 cook settings.

DANGER

Do not over-ﬁre the smoker by over feeding pellets into

the burner prior to startup. If ﬂame is inadvertently

extinguished never restart the smoker without ﬁrst

cleaning out the burner. Improper use can cause an

uncontrolled ﬁre.

Shutdown

When you are done cooking the dial must be turned to the

Shutdown setting. The digital readout will display “SDOWN”.

In this setting the fan will remain on for 10 minutes to

ﬁnish burning any pellets in the burner and cool the smoker

down. After 10 minutes the digital display and auger will

turn off. At this point the main power switch should be

switched to off. Before smoker can be used, the power

switch must be turned off and back on.

Bypass Mode

The bypass may be used if there is a power failure, or the

smoker is accidentally turned off, or anytime you need to

restart the smoker and it is still hot. The bypass mode

should only be used if the smoker has been off less than

3-4 minutes. This method is used to bypass the normal

startup mode and get the smoker cooking again quickly.

The burner must still be hot enough to ignite new pellets

or this method will not work. In order to initiate the bypass

mode you must ﬁrst select the cook setting you want. At this

point the digital readout will display “START”. Simply press

the bypass button in and hold it for 3 seconds. The digital

readout will display “BPASS”. Release the button and the

smoker will go into the cook mode and the digital readout

will display the smoker temperature. If the smoker fails to

ignite using the bypass mode then restart the smoker using

the normal startup procedures.

Meat Probes

This smoker has built in meat probes to measure the

temperature of the food as it is being cooked. To use these

probes insert the wire through the stainless ﬂaps on the

side of the ﬁrebox. Insert the probes into the food. Plug the

connectors into the receptacles on the front of the control

panel. When you press the probe temp button on the front

of the controller the digital readout will display the food

temperature. Press the button a second time to toggle the

display to the other probe. Press the button a third time to

toggle back to the cooking temperature. If the probes are

not installed correctly or there is an error with the probes

the digital readout will display “PRERR” when the probe

temp button is pressed. When running the probe wires to

the food make sure it is positioned out of direct contact with

any open ﬂame or damage may occur. The digital readout

will display a “X” in front of the number when displaying

the “X” meat probe temperature and a “Y” for the “Y” meat

probe temperature. Example: “X155F”

DANGER

Do not turn the main power switch off while the smoker

is hot.

Cleaning

Clean grates using a wire grill brush. This should be

done with each use. DO NOT use oven cleaner or abrasive

cleaners on the painted smoker surfaces. Use warm soapy

water on all painted surfaces. Clean grease pan, grease

trough, and grease drain tube occasionally. A spatula can

be used to scrape excess grease and a grill brush to brush

clean. Do not allow grease to build up on the grease tray or

in the grease trough as this can cause ﬂare-ups inside the

smoker. The grease tray can also be lined with aluminum

foil for easier cleanup. Make sure not to obstruct the ﬂow of

grease off of the tray and into the grease trough. Make sure

not to block the airﬂow to the temperature sensor on the left

side of the smoker.

WARNING

Normal use will create a buildup of ash, grease,

and creosote inside the smoker. The smoker must be

thoroughly cleaned after every 50 hours of use or if

a buildup of grease or creosote is noticed inside the

smoker. Clean the smoker by removing all internal parts

and thoroughly scrape away all grease and creosote

from all internal surfaces including the grease drain

and remove debris from the smoker. The drip tray must

always be cleaned prior to turning the smoker to high.

Excessive buildup of grease and creosote may result in a

grease ﬁre. If a grease ﬁre does occur, turn off the smoker

using the main power switch and close the door. Leave

the door closed until the ﬁre extinguishes itself. If an

uncontrolled ﬁre does occur, immediately call the local

ﬁre department. Never put water on a grease ﬁre.

Smoker Cleaning

When wood pellets are burned slowly, they produce tar and

other organic vapors that combine with expelled moisture to

form creosote. The creosote vapors condense in a relatively

cook oven chimney of a slow burning ﬁre. As a result,

creosote residue accumulates on the smoker walls. When

ignited, this creosote makes an extremely hot ﬁre. The smoker

walls should be inspected every 50 hours to determine when

grease and or creosote buildup has occurred. When grease

or creosote has accumulated, it should be removed to reduce

risk of ﬁre. Use spatula or a wire brush to clean the smoker

walls with every 50 hours of use.

Troubleshooting

Smoker does not turn on.

Smoker fails to turn on after switching the power button to

the on position.

1. Make sure the smoker is plugged into a powered outlet.

Check the circuit breaker and/or GFCI switch. Test the

outlet using another appliance.

2. Unplug the smoker and check the fuse located in the

front panel. If the fuse is blown replace only with 4.0 Amp

125V 5x20mm Fast Blow Fuse. Typical fuse marking will

be 4A125V, F4A125V, 4A250V, or F4A250V. Make sure to

conﬁrm they are a fast blow fuse. Actual fuse dimensions

are 5.2x20mm. If problem cannot be resolved please call

customer service.

Smoker does not heat up or digital readout

displays Flame

1. Turn Power Off

2. Check hopper for pellets

3. Check ﬁrebox to see if there are pellets in the ﬁrebox.

The easiest way to do this is to pull the burner clean-out

lever. Then remove the cup from the bottom of the smoker

and check for pellets. Use a vacuum to clean-out any

pellets that may be in the bottom of the smoker.

A. If there are a lot of pellets in the cup. Reinstall the

cup and close the burner clean-out, remove the smoker

grates, grease tray, and heat deﬂector and vacuum out

any pellets in the bottom of the smoker. Try restarting the

smoker. If restarting the smoker does not work and pellets

are getting to the burner cup the heating rod may need to

be replaced.

B. If there are few or no pellets in the cup then turn the dial

to the feed position and see if pellets fall out the bottom

of the burner. If there are no pellets check to see if the

auger is turning. If the auger motor is turning but the

auger is not there may be a sheared auger pin. You can

determine if the auger motor is turning by watching the

small white fan at the end of the auger motor under the

hopper. If the white fan is turning the auger motor is on. If

the white fan is turning and the auger is not you will need

LIMITED WARRANTY

Camp Chef No-Hassle Warranty

Here at Camp Chef we stand by our products and take pride in our

customer service. Because of this, your new Camp Chef product comes

with a No-Hassle Warranty. What does that mean? It means that if we

did something wrong, we will make it right. We guarantee our products

to be free from defect in all materials and workmanship (excluding

paint and ﬁnish). We will replace defective parts so you can get back to

enjoying your product as soon as possible.

Required Maintenance:

Clean your product after each use to maintain its ﬁnish and prolong

its lifespan. Wipe away all grease and ashes. Keep metal products

free of moisture, salts, acids and harsh ﬂuctuations in temperature.

Unfortunately, product paint and other ﬁnishes are not covered by this

warranty. The exterior ﬁnish of the product will wear down over time.

Coverage Details:

Warranty does not cover normal wear of parts or damage caused

by misuse, abuse, overheating and alteration. No alterations are

covered in this warranty. Camp Chef is not responsible for any loss

due to neglectful operation. Furthermore, this warranty does not cover

items purchased from a 3rd party company, unauthorized dealers, or

damages caused by natural disasters such as earthquakes, hurricanes,

tornadoes, ﬂoods, lightning, ﬁres, etc.

Upon the expiration of this warranty, all such liability will terminate. No

other warranties are expressed or implied.

Please keep all original sales receipts from the authorized dealer.

Proof of purchase is required to obtain warranty services. Any parts

or products returned without written authorization will be discarded

without notice.

To obtain warranty services submit a warranty request at

http://www.campchef.com/warranty-information, email warranty@

campchef.com, or call 1.800.650.2433. Mon-Fri 7 AM-5 PM MST

Our English speaking Product Specialists are happy to help.

Warranty applies to the contiguous U.S. states only.

WARRANTY COVERAGE PERIODS

Pellet Grills 3 years from purchase date

Stoves 1 year from purchase date

Fire Pits 1 year from purchase date

Water Heaters 1 year from purchase date

Movie Screens 1 year from purchase date

All other items & accessories 90 days from purchase date

to replace the auger pin. If problem cannot be resolved

please call customer service.

Digital Readout Displays SENSR

1. Turn the power off and unplug the smoker.

2. Check to make sure the sensor inside of the smoker is

connected properly to the electronic board under the

hopper.

3. Call customer service for a replacement sensor.

Digital Readout Displays PRERR

1. Press the Probe Temp button - Pressing the Probe Temp

button will toggle the digital readout between the actual

temperature inside of the smoker and the temperature

measured using the meat thermometer.

2. Make sure the meat thermometer is connected properly

to the front of the smoker. If the Probe Temp button is

pressed to display the Probe Temp without the meat

thermometer properly connected to the front of the

smoker it will display PRERR.

3. Call customer service for a replacement meat

thermometer.

Digital Readout Displays “-----”

1. Rotate the dial from Shutdown to feed or any other cook

setting.

White

Black

Auger Motor Blower Fan

Burner

Controller

RTD Sensor

Power Cord

White

Red

White

Orange

White

Purple

Hot Rod

MOLEX Connector

4A 125V

4 amp 125V

5 x 20 MM

Fast Blow Fuse

CAUTION

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1 this device may not

cause harmful interference, and 2 this device must accept any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

BARBECUE À GRANULES

AVERTISSEMENT & INSTRUCTION BROCHURE

MODÈLE: PGVXXL

www.CampChef.com | 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

AVERTISSEMENT

DESTINÉ À UN USAGE EN PLEIN

AIR UNIQUEMENT

AVERTISSEMENT

• À l’attention de l’installateur ou de la personne

chargée d’assembler cet appareil : conserver

la présente notice d’utilisation avec l’appareil

pour un usage ultérieur.

• À l’attention du consommateur : conserver la

présente notice pour un usage ultérieur.

La présente notice d’utilisation contient des

informations importantes nécessaires au

montage correct et à l’utilisation sécuritaire de

ce produit.

NE PAS JETER LA PRÉSENTE NOTICE D’UTILISATION.

AVERTISSEMENT

1. Ne jamais faire fonctionner cet appareil sans

surveillance.

2. N’utilisez jamais cet appareil à moins de 10 pi

(3 m) d’une bouteille de GPL conservée.

3. Ne jamais utiliser le présent appareil à moins

de 7,5 m (25 pi) de tout liquide inflammable.

4. En cas d’incendie, rester à bonne distance de

l’appareil et appeler immédiatement le service

des incendies. Ne pas essayer d’éteindre un

feu d’huile ou de friture avec de l’eau.

Le non-respect de ces consignes peut

entraîner des dommages matériels, des

blessures corporelles ou la mort pouvant

résulter d’un incendie, d’une explosion ou

d’un danger de brûlure.

AVERTISSEMENT

Entreposer en permanence les granules de bois

à l’abri des appareils produisant de la chaleur

et d’autres récipients alimentaires. Les granules

doivent être entreposés dans un endroit sec.

CAUTION

Contacter les autorités locales du bâtiment

ou de la protection incendie pour connaître les

restrictions et les exigences d’inspection en

vigueur dans votre région.

LE NON-RESPECT DES DÉGAGEMENTS (ESPACES

VIDES) REQUIS POUR LES MATÉRIAUX

COMBUSTIBLES CONSTITUE UNE DES PRINCIPALES

CAUSES D’INCENDIES. IL EST DONC PRIMORDIAL

D’INSTALLER CE PRODUIT CONFORMÉMENT À LA

PRÉSENTE NOTICE.

CAUTION

Utiliser uniquement les granules de bois indiqués

par le fabricant. Ne pas utiliser de granules de

bois dont les spéciﬁcations indiquent la présence

d’additifs. Utiliser uniquement des granules de

bois Camp Chef de première qualité répondant aux

spéciﬁcations suivantes : 8 000 à 8 300 BTU/LB

Taux de cendre de 0,75 à 0,85 %

AVERTISSEMENT

Une utilisation normale créera une accumulation

de cendres, de graisse et de créosote dans le

fumeur. Le fumeur doit être nettoyé à fond toutes

les 50 heures d’utilisation ou si une accumulation

de graisse ou de créosote est observée à l’intérieur

du fumeur. Nettoyez le fumeur en enlevant toutes

les pièces internes et enlevez soigneusement

toutes les graisses et créosotes de toutes les

surfaces internes, y compris le drain de graisse et

enlevez les débris du fumeur. Le bac d’égouttement

doit toujours être nettoyé avant de mettre le fumeur

en position haute. Une accumulation excessive de

graisse et de créosote peut provoquer un incendie

de graisse. Si un feu de graisse se produit,

éteignez le gril à l’aide de l’interrupteur principal

et fermez le porte. Laissez le porte fermé jusqu’à ce

que le feu s’éteigne. En cas d’incendie incontrôlé,

appelez immédiatement le service d’incendie local.

Ne jamais mettre de l’eau sur un feu de graisse.

AVERTISSMENT CONCERNANT LE MONOXYDE DE CARBON

Avertissement concernant le monoxyde de carbone Respecter les présentes directives pour éviter de vous faire intoxiquer

et d’intoxiquer vos proches par ce gaz incolore et inodore. Vous devez connaître les symptômes d’une intoxication

au monoxyde de carbone : il s’agit de maux de tête, de vertiges, de faiblesses, de nausées, de vomissements, de

somnolence et de confusion. Le monoxyde de carbone réduit la capacité sanguine pour transporter l’oxygène. Un faible

taux d’oxygène dans le sang peut entraîner des pertes de connaissance, voire la mort. Consultez un médecin si vous ou

autrui développez des symptômes du rhume ou s’apparentant à la grippe en cuisinant à proximité de cet appareil. Une

intoxication au monoxyde de carbone, souvent confondue par erreur avec un rhume ou la grippe, est souvent détectée

trop tard. La consommation d’alcool ou de drogues renforce les effets de l’intoxication au monoxyde de carbone.

Le monoxyde de carbone est particulièrement toxique pour les femmes enceintes et leur fœtus, les jeunes enfants, les

personnes âgées, les fumeurs et les personnes souffrant de troubles sanguins ou circulatoires, comme l’anémie ou des

maladies cardiaques.

0918 PGXXL PARTS

PIÈCES PGXXL

Sacs de quincaillerie:

PGXXL-13

Quincaillerie pour les pieds et le réservoir

Qty (16) Seize boulons M6 x 15

Qty (2) Deux vis autotaraudeuses M4

PGXXL-10

Quincaillerie pour le rail métallique

Qty (8) Huit boulons M6 x 20

Qty (8) Huit rondelles plates M6

Qty (8) Huit écrous kep M6

PGXXL-11

Quincaillerie pour le support du déflecteur de chaleur

Qty (4) Quatre vis M4 x 10

PGXXL-12

Quincaillerie pour le cache de la sonde et le thermomètre

Qty (4) Quatre vis autotaraudeuses #8-32

PG24-9 (1)

BOUTON DE LA

TRAPPE DU BRÛLEUR

PG24-42 (1)

SYSTÈME DE BLOCAGE

DE LA TRAPPE DU BRÛLEUR

PG24-41 (1)

TRAPPE DU BRÛLEUR

PG24-17 (1)

ASH CUP

PG24-34 (1)

JOINT DU SYSTÈME

D’ALIMENTATION

PG24-44 (1)

THERMOMÈTRE

PG24-54 (2)

CACHE DE LA SONDE

PG24-4 (1)

DÉFLECTEUR DE CHALEUR

SMV-45 (3)

GRILLE POUR CHARQUI ET

FRUITS DE MER

SMV-38 (4)

GRILLE DE CUISSON

SMV-3 (1)

REGISTRE D’AIR

SMV-40 (1)

POIGNÉE MÉTALLIQUE SMV

SSG24 (1)

GRILLE POUR SAUCISSES

PGXXL-17 (1)

ENSEMBLE DE LA POIGNÉE

PG36-7 (4)

ROULETTE PIVOTANTE

PGXXL-1

LÈCHEFRITE

PGXXL-2 (2)

RAIL MÉTALLIQUE

PGXXL-3 (1)

CACHE DE LA SONDE

PGXXL-16 (1)

ENSEMBLE DU RÉSERVOIR

PGXXL-5 (1)

PANNEAU DE PORTE

PGXXL-6 (1)

PANNEAU DE PORTE DU BAS

PGXXL-7 (2)

SUPPORT DU DÉFLECTEUR

DE CHALEUR

PGXXL-8 (4)

PIED

PG24-11 (1)

SEAU DE COLLECTE DES GRAISSES

M5 SHOULDER VIS

PGXXL-15 (2)

DOOR HINGE

0117 PGXXL PARTS

PG24-28 (2)

Sonde à viande

PG24-46 (1)

Plaque de Garde

PG24-45 (1)

Joint de contrôleur

Vis M4.2 x 10 (2)

PG24-30 (1)

Bouton du panneau de commande

PGXXL-9 (1)

Contrôleur

PG24-9 (1)

Bouton retrait

PG24-42 (1)

serrure retrait

PGC24-13 (1)

Hopper nettoyage

boulon M6 X 15(2)

écrou M6 (2)

PG24-48 (1)

Cordon d'alimentation

PGC24-18 (1)

LID MAGNET

PG24-53 (1)

Garde Auger

PG24-52 (1)

Hopper râteau

PG24LS-11 (1)

Couvercle noir

du réservoir à granules

Rondelle plate M6

Rondelle frein M6 (2)

Écrou M6 (2)

M6 X 15 SCREW (2)

PG24-49 (1)

Auger roue

PG24-24 (1)

Moteur de la vis sans fin de transport

PG24-23 (1)

Douille de la vis sans fin de transport

PG24-25 (1)

Axe de la vis sans fin avec écrou

PGC24-8 (1)

Vis sans fin de transport

PG24-27 (1)

Roue du système de ventilation

Vis M4.2 x 10 (4)

PG24-26 (1)

Moteur du système de ventilation

PG24-21 (1)

Bougie d'allumage

PG24-20 (1)

Brûleur

Vis M4.2 x 10 (4)

1. NE PAS laisser l’appareil sans surveillance lorsqu’il

fonctionne. L’utilisateur est tenu de rester à proximité du

produit et de garder celui-ci dans son champ de vision

direct pendant toute la durée de son fonctionnement.

2. Tenir les enfants et animaux domestiques à l’écart du

brûleur en permanence.

3. La consommation d’alcool, ou de médicaments obtenus

ou non sur ordonnance, risque de diminuer votre faculté

de monter correctement l’appareil ou de l’utiliser en toute

sécurité.

4. Destiné à un usage EN PLEIN AIR uniquement. NE PAS

utiliser à l’intérieur d’un immeuble, d’un garage ou de

tout autre endroit fermé. NE PAS utiliser dans un véhicule

récréatif ou sur un bateau. NE JAMAIS utiliser cet appareil

comme système de chauffage.

5. Ne faire fonctionner cet appareil sous AUCUNE surface

surplombante. Conserver une distance minimale de

0.5 m (18 pi) entre les quatre côtés de l’appareil et

TOUTE construction. N’entreposer aucuns matériaux

combustibles et liquides inﬂammables, plantes et

herbes sèches, buissons, papiers et toiles à proximité de

l’appareil.

6. Cet appareil n’est pas destiné à un usage commercial.

7. Toujours laisser l’appareil refroidir avant de le recouvrir

de sa housse d’extérieur.

8. Toujours recouvrir l’appareil de sa housse d’extérieur

(lorsqu’elle est fournie) lorsque l’appareil ne sert pas.

9. Toujours débrancher le barbecue avant de le recouvrir de

la housse d’extérieur.

10. Utiliser uniquement sur une surface stable et non

combustible comme les briques, le béton ou la saleté.

N’utilisez pas cet appareil sur une surface qui brûlera

ou fondra comme du bois, de l’asphalte, du vinyle ou du

plastique.

11. Assurez-vous que le seau à graisse est en place avant

de démarrer le gril.

12. En cas d’incendie, placer le bouton de commande sur

la position SHUTDOWN, fermer le couvercle et le laisser

fermé jusqu’à extinction du feu. Lorsque le barbecue

aura refroidi, suivre les consignes de nettoyage avant la

prochaine utilisation.

13. Utiliser uniquement des granules de feuillu à usage

alimentaire qui sont fabriqués pour être utilisés dans

des barbecues à granules. L’utilisation de granules

de conifères ou de bois de chauffage annulera votre

garantie.

14. Ne pas laisser le réservoir à granules se vider

complètement de granules. Les granules peuvent être

ajoutés à tout moment. Le réservoir peut contenir

environ 6,8 kg de granules. La consommation de

granules variera considérablement en fonction de la

température ambiante ainsi que de la température de

cuisson.

15. Il vous est recommandé de ne pas entreposer les

granules dans leur réservoir pour des périodes

prolongées ; ils peuvent en effet absorber l’humidité de

l’air et obstruer la vis sans ﬁn de transport.

16. Garder le couvercle fermé pendant le fonctionnement

du barbecue. Le barbecue est conçu pour cuisiner en

gardant le couvercle fermé.

17. Ne pas utiliser d’accessoires dont l’utilisation n’est pas

indiquée avec cet appareil.

18. Ne jamais employer d’essence de carburant de lanterne

de type essence, de kérosène, de produit d’allumage

pour charbon ou de liquides semblables pour démarrer

ou raviver un feu dans cet appareil. Garder tous ces

liquides à bonne distance de l’appareil pendant qu’il est

en service.

19. Les cendres doivent être déposées dans un conteneur

métallique possédant un couvercle hermétique. Le

conteneur fermé qui contient les cendres doit être placé

sur une surface non combustible ou sur le sol, très

loin des matériaux combustibles jusqu’à l’élimination

déﬁnitive des cendres. Si les cendres sont destinées à

être enterrées dans le sol ou dispersées autrement sur

place, elles devraient être conservées dans le conteneur

jusqu’à ce qu’elles soient complètement refroidies.

20. La créosote – Formation et nécessité de la retirer.

Lors de leur lente combustion, les granules de bois

produisent du goudron et d’autres vapeurs organiques

qui, combinés à l’humidité rejetée, forment la créosote.

Les vapeurs de créosote se condensent dans les tuyaux

d’évacuation d’un four relativement froid et dans la

hotte de ventilation d’un foyer à combustion lente. Il

en résulte une accumulation de résidus de créosote

dans les tuyaux d’évacuation et la hotte de ventilation.

Une fois mise à feu, cette créosote produit un feu

brûlant. Le tuyau d’évacuation des graisses doit être

inspecté au moins deux fois par an pour déterminer si

une accumulation de graisse et/ou de créosote s’est

produite. Si tel est le cas, cette accumulation doit être

enlevée pour réduire le risque d’incendie.

DANGER

Ne pas effectuer de travaux sur le barbecue lorsque celui-

ci est branché. L’électrocution qui risquerait de se produire

pourrait entraîner le décès ou des blessures graves.

Consignes De Montage Des Pieds

Avec l’aide d’une autre personne,

Retirer toutes les pièces détachées se trouvant à l’intérieur

du barbecue et du réservoir.

Déposer par terre une couverture ou un morceau de carton

par terre pour protéger le barbecue.

1. Placer le boîtier du fumoir en position verticale et enlever

la porte en la soulevant hors de ses charnières. Laisser le

panneau de la porte sur le côté pour faciliter le montage.

2. Placer l’ensemble du fumoir, face avant contre le sol, sur

une surface rembourrée (ex. carton ou tapis) pour éviter

de griffer ou d’abîmer celui-ci.

3. Monter les quatre pieds comme illustré à l’aide des douze

boulons M6 x 15. FIG. 1

M6 x 15

FIG. 1

4. Monter le système de blocage de la trappe du brûleur à

l’aide de deux boulons à épaulement M6 et deux écrous

M6. FIG. 2

FIG. 2

4. Install Stop Lock using Qty (2) M6 Shoulder Bolts and

Qty (2) M6 nuts.

5. Install Burner Pullout by sliding it through the

side where the Stop Lock was installed.

6. Install Stop Lock Bushing on the Burner Pullout.

Then install the Pull Knob on the Burner Pullout.

screws.

Système de blocage

Boulon à épaulement M6

Écrou M6

5. Monter la trappe du brûleur en l’insérant du côté où son

système de blocage a été monté. FIG. 3

FIG. 3

SCALE 0.100

Trappe du brûleur

6. Monter la bague du système de blocage sur la trappe du

brûleur. Monter ensuite le bouton de la trappe du brûleur

sur l’extrémité de sa tige. FIG. 4

FIG. 4

SCALE 0.100

7. Installer les deux supports du déﬂecteur de chaleur avec

huit vis M4 x 10. FIG. 5

FIG. 5

M4 x 10

Support du déflecteur

de chaleur

8. Installez le décapsuleur comme indiqué à la Fig. 6.

M6 X 15MM SCREW

BOTTLE OPENER

M6 LOCK WASHER (2)

M6 FLAT WASHER (2)

HOPPER HANDLE (1)

PGC24-12

M6 RUBBER WASHER (2)

FIG. 6

9. Installez la poignée de la trémie comme indiqué sur la

Fig. 7.

M6 X 15MM SCREW

BOTTLE OPENER

M6 LOCK WASHER (2)

M6 FLAT WASHER (2)

HOPPER HANDLE (1)

PGC24-12

M6 RUBBER WASHER (2)

FIG. 7

La page charge ...

Camp Chef PGVXXL Mode d'emploi

Marque: Camp Chef

Modèle: PGVXXL

Taper: Mode d'emploi

Ce manuel convient également à

PGVXXLC

Télécharger le PDF

rapport

dans d''autres langues

English: Camp Chef PGVXXL Operating instructions

Camp Chef PGVXXL Mode d'emploi

Ce manuel convient également à

Camp Chef PGVXXL Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents