IKEA IHW8305WS0 Guide d'installation

Marque: IKEA

Modèle: IHW8305WS0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

36"(91.4 CM) WALL-MOUNTCANOPY

RANGE HOOD

HOTTEDECUISINIEREPOURMONTAGE MURAL

36"(91,4 CM)

Table of Contents/Table des matieres ............................................................................. 2

IMPORTANT: READ AND SAVETHESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : URE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RCSIDENTIELLE UNIQUEMENT.

IMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

Save installation instructions for local electrical inspector's use.

IMPORTANT :

InstaJlateur : Remettre les instructions d'installation au propri_taire.

Propri_taire : Conserver les instructions d'installation pour r_f@ence ult@ieure.

Conserver les instructions d'installation pour consultation par I'inspecteur local des installations _lectriques.

W10018010

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Venting Requirements .................................................................. 5

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 6

Prepare Location .......................................................................... 6

Install Range Hood ....................................................................... 7

Connect Vent System .................................................................. 8

Make Electrical Connection ......................................................... 8

Complete Installation ................................................................... 9

Install Filters ................................................................................ 10

Check Operation ........................................................................ 10

RANGE HOOD USE ...................................................................... 10

Operation .................................................................................... 10

RANGE HOOD CARE ................................................................... 11

Cleaning ...................................................................................... 11

WIRING DIAGRAM ...................................................................... 12

ASSISTANCE OR SERVICE ......................................................... 13

In the U.S.A................................................................................ 13

In Canada ................................................................................... 13

WAR RANTY .................................................................................. 14

TABLEDESMATIERES

SECURITE DE LA HOTTE DE CUlSINIERE ............................... 15

EXIGENCES D'INSTALLATION ................................................... 17

Outillage et pieces ...................................................................... 17

Exigences d'emplacement ......................................................... 17

Exigences concernant I'evacuation ........................................... 18

Specifications electriques .......................................................... 19

INSTRUCTIONS D'INSTALLATION ............................................. 20

Preparation de I'emplacement ................................................... 20

Installation de la hotte ............................................................... 21

Raccordement du circuit d'evacuation ...................................... 22

Raccordement electrique ........................................................... 22

Achever I'installation.................................................................. 23

Installation des filtres .................................................................. 24

Contr61e du fonctionnement ...................................................... 24

UTILISATION DE LA HOTTE ....................................................... 24

Fonctionnement ......................................................................... 24

ENTRETIEN DE LA Ho'n'E .......................................................... 25

Nettoyage ................................................................................... 25

SCHEMA DE C.&,BLAGE .............................................................. 26

ASSISTANCE OU SERVICE ......................................................... 27

GARANTIE .................................................................................... 28

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

[] Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

[] Before servicing or cleaning the unit, switch the power off at

the service panel disconnecting means to prevent power

from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service

panel.

[] Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

& standards, including fire-rated construction.

[] Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

[] When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

[] Ducted systems must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls ceilings, attics, crawl spaces, or

garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave the surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

other metal tray, then turn off the gas burner or electric

element. BE CAREFUL TO PREVENT BURNS. If the

flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN - you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

SAVE THESE iNSTRUCTiONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill with 1%" (3 cm), 3/8"(9.5 mm), %4" (2.75 mm) and

V8"(3 mm) drill bits

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

Parts needed

• V2"conduit

• Two 1/2"(12.7 mm) UL listed or CSA approved strain reliefs

• 3 UL listed wire connectors

• 1 wall or roof cap

• Metal vent system

• Charcoal Filter Kit Part Number 4396850 - for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

Parts supplied

Remove parts from packages. Check that all parts are included.

• Hood canopy assembly with ventilator, light bulbs and

transition with back draft dampers installed

• Deflector for non-vented (recirculating) installations

• Literature package

• Filter- installed in hood canopy

• 2-5x35mmscrews

• 4-4x8mmscrews

• 2-6x70mmscrews

• 6- 3.5 x 6.5 mm screws

• 4- 2.9 x 6.5 mm screws

• 3- M4 x 35 mm screws

• 2 - 10 x 70 drywall anchors

• Mounting template

• Lower support bracket

• Vent cover bracket

• 2- L-brackets

• 2- Mounting hooks

• 2-piece vent cover

• Aesthetic cover

• Rubber strip (1 or 2 to be cut as required)

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the filter on the rear wall of the range

hood.

Range hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The range hood is factory set for venting through the roof or wall.

For non-vented (recirculating) installations see "Non-vented

(recirculating) Installations" in "Connect Vent System" section.

Charcoal Filter Kit Part Number 4396850 is available from your

dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed

must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

*IMPORTANT: For non-vented (recirculating) installations,

minimum dimension is 6" (15.2 cm).

Installation Dimensions

10 1/2" (26.7 cm)

(30.5 cm)

Side

cabinet

12"

cm) ram.

21"

i (s3.3cm)

30 power

supply cabJe entry

location

Side

cabinet

36" I l

--_ (91.4 cm) i --

mJn.

J 30" (76.2 cm) rain.

Centerline I bottom of canopy to

cooking surface

• Vent system must terminate to the outside, except for non-

vented (recirculating) installations.

• Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall caps.

• Use metal vent only. Rigid metal vent is recommended. Do

not use plastic or metal foil vent.

• The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

For the most efficient and quiet operation:

• Use a straight run or as few elbows as possible.

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow. A nonmetallic thermal break should be

installed to minimize conduction of outside temperatures as part

of the vent system. The damper should be on the cold air side of

the thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement.

The specified CFM varies from locale to locale. Consult your

HVAC professional for specific requirements in your area.

Venting Methods

This canopy hood is factory set for venting through the roof or

wall.

An 8" (20.3 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 8" (20.3 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

Rear discharge

A 90° elbow may be installed immediately above the hood.

For non-vented (recirculating) installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting an activated carbon filter and the deflector. Fumes

and vapors are recycled through the top grille.

Roof Venting Wall Venting Non-vented

(recirculating)

..........A

A ...........

A. Roof cap A. Wall cap A. Deflector

B. 8" (20.3 cm) B. 8" (20.3 cm) B. 8" (20.3 cm)

round vent round vent round vent

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent piece 8" (20.3 cm) round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

Maximum equivalent vent length is 50 ft (15.2 m).

Example Vent System

,o ° elbow I-_-_ 6. (_.8m)-_,,_l Wall cap

The following example falls within the maximum vent length of

50 ft (15.2 m).

1 - 90° elbow

1 - wall cap

8 ft (2.4 m) straight

System length

= 5.0 ft (1.5 m)

= 0.0 ft (0.0 m)

= 8.0 ft (2.4 m)

= 13 ft (3.9 m)

IMPORTANT: Observe all governing codes and ordinances. Save

Installation Instructions for electrical inspector's use.

It is the customer's responsibility to contact a qualified electrical

installer, and to ensure that the electrical installation is adequate

and in conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is

required.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure range

hood is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

• The range hood must be connected with copper wire only.

• The range hood should be connected directly to the fused

disconnect (or circuit breaker) box through flexible armored or

nonmetallic sheathed copper cable. It is recommended that a

separate circuit serving only this hood be provided.

• Wire sizes (copper wire only) and connections must conform

with the rating of the appliance as specified on the model/

serial rating plate. The model/serial plate is located behind

the filter on the rear wall of the hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSl/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

• A W' (12.7 mm) UL listed or CSA approved strain relief must

be provided at each end of the power supply cable (at the

range hood and at the junction box).

INSTALLATIONINSTRUCTIONS

It is recommended that the vent system be installed before

hood is installed.

Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting frame must be

constructed.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check your ceiling height and the hood height maximum

before you select your hood.

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to rear

wall. Otherwise put a thick, protective covering over

countertop, cooktop or range to protect from damage or dirt.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Cover

that surface with a protective covering..

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto protective

covering.

5. Determine and mark the centerline on the wall where the

canopy hood will be installed.

6. Select a mounting height between a minimum of

30" (76.2 cm), and a suggested maximum of 36" (91.4 cm)

above the cooking surface and mark a reference line on the

wall.

Tape template in place, aligning the template centerline and

bottom of template with hood bottom line and with the

centerline marked on the wall.

¸%%¸¸¸ i/iF

A. Centerline

B. Lower support bracket

C. 5 x 35 mm screws

D. Mounting height reference

E. Fastener locations

F Wall

Place the lower support bracket on the template aligning it

with the traced rectangle. Mark centers of 3 fastener

locations through the template to the wall.

IMPORTANT: All screws must be installed into wood.

Remove the template.

9. Drill %4" (2.75 mm) pilot holes at 2 upper locations where

screws are being installed into wood.

10. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements" section.

11. Determine the required height for the 1/2"conduit and drill a

11¼"(3.2 cm) hole at this location.

12. Run the 1/2"conduit through the hole. Run wire through the

1/2"conduit according to the National Electrical Code or CSA

Standards and local codes and ordinances. There must be

enough 1/2"conduit and wires from the fused disconnect (or

circuit breaker) box to make the connection in the hood's

electrical terminal box.

13. Use caulk to seal all openings.

NOTE: Do not reconnect power until installation is complete.

14. Attach the lower support bracket to the wall using

2 - 5 x 35 mm screws at location marked on the template.

A. Lower support bracket

B. Mounting hooks

C. Adjust side to side.

A. Lower support bracket

B. Centerline on wall

C. 5 x 35 mm screws

Vent Cover Bracket Assembly and Installation

1. Assemble the 3 pieces of the vent cover bracket using 4 -

4 x 8 mm screws provided. The assembled bracket should be

sized to fit inside the upper vent cover.

A. Vent cover bracket assembly

B. Upper vent cover

C. 4 x 8 mm screws

D. Adjustable width

Install vent cover bracket to wall about 1/8"(3 mm) away from

the ceiling with 2 - 6 x 70 mm screws and 2 - 10 x 70 drywall

anchors supplied.

i ...............................g

A. Vent cover bracket

B. Centerline on wall

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Using 2 or more people, hang blower housing on the lower

support bracket using the 2 mounting hooks on the rear of

the blower housing.

A. Lower support bracket

B. Mounting holes

C. Adjust side to side

D.Adjust up and down

E. Blower housing

2. Level the blower housing with leveling screws in mounting

hooks, using a level across bottom of blower housing.

3. Remove the metal grease filter and secure the blower

housing with one screw in the bottom hole located in the rear

of the blower.

4_" Ac__, B

A. Rear of blower housing

B. Bottom 5 x 35 screw hole

_,_,_o_F_s_'@C_@ _/s@_ +_

Vented Installations Only

1. Fit vent system over transition piece.

2. Seal connection with clamps.

Non-vented (recirculating} Installation

1. Assemble the 3 parts of the deflector with 2 - 3.5 x 6.5 screws

provided. The assembled deflector should be sized to fit the

width of the vent cover bracket installed earlier.

Mc <® Eecff ccl Connec on

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Remove terminal box cover.

3. Remove the knockout.

S ....

A. Vent cover bracket width

B. Deflector

C. 3.5 x 6.5 mm screws

Connect the deflector to the vent cover bracket using

4 - 3.5 x 6.5 screws provided.

A. Knockout

B. Terminal box cover

4. Install the UL listed or CSA approved strain relief.

A. Vent cover bracket

B. 3.5 x 6.5 mm screws

3. Measure length of 8" (20.3 cm) vent needed to connect the

transition to the deflector.

NOTE: Vent should fit up inside deflector a minimum of

1" (2.5 cm).

4. Install vent between the transition and the deflector.

5. Seal all connections with clamps.

A. Y2"conduit

B. Terminal box cover

C. UL fisted or CSA approved strain relief

D. Green (or bare) wire connected to yellow-green wire

E. White wires

F. Black wires

5. Run 3 wires, black, white and green (14 AWG), in 1/2"conduit

from service panel to terminal box.

6. Use UL listed wire connectors and connect black wires

together.

7. Use UL listed wire connectors and connect white wires

together.

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

8. Connect ground wire to green and yellow ground wire in

terminal box using UL listed wire connectors.

9. Replace terminal box cover.

10. Check all light bulbs to make sure they are secure in their

sockets.

11. Reconnect power.

1. Check lights and blower operation. See "Range Hood Use"

section.

If hood does not operate:

• Check that the circuit breaker is not tripped or the

household fuse has not blown.

• Disconnect power. Check that wiring is correct.

2. For non-vented (recirculating) installations, install the

charcoal filter. See "Install Filters" section.

3. Place the 2 L-brackets onto the glass hood.

A.L-bracket

4. Slide the glass hood on the blower housing.

5. Attach M4 x 35 screws to secure the glass hood.

A. M4 x 35 screws

6. Install vent cover by placing both vent covers on the hood.

7. Secure lower vent cover to hood with 2 - 2.9 x 6.5 mm

screws, one on either side.

8. Lift upper vent cover to the ceiling.

9. Secure upper vent cover to vent cover bracket with 2 - 2.9 x

6.5 mm screws. Do not completely tighten the lower screws,

but leave a clearance of about V16"(2 mm).

A. Vent cover bracket

B. Upper vent cover

C. Lower vent cover

D. 2.9 x 6.5 mm screws

10. Apply 2 rubber strips on the inside of the aesthetic cover.

A _¸¸

A.Rubber strips

11. Fit over the glass visor. The rubber strips will work to protect

duct covers against any damage when fitting the cover.

Whenfittingthecover,checkthatthesiderailsfitinthe

properhead-screws(thoseusedtofixthelowerventcoverto

thehood)ontherightandleftsideoftheduct.

Toreplacethemetalgreasefilters:

1. Insertbackedgeoffilterintorearchannelofthefilter

opening.

2. Pushhandletowardtherearandpushfilterup.

3. Pullfiltertowardthefrontandinsertintofrontchannel.

A, Lower vent cover screws

B. Glass visor

C. Aesthetic cover

For non-vented (recirculating) installations

1. Turn off blower and lights. Check that halogen lamps are

cool.

2. Remove the metal grease filters by pushing handle toward

the rear and pull downward.

o ©@©@

A B C D E

A. Indicator light

B. Light button

C. Low speed button

D. Medium speed button

E. High speed button

1. Press the "B" button. The light should turn on.

2. Press the "C" button. The blower should turn on at low

speed.

3. Press the "D" button for medium speed or the "E" button for

high speed.

4. Press the "B" button to turn off the light. Press the "C" button

to turn off blower

5. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

6. Disconnect power supply.

7. Check that the wiring is correct.

8. Replace all parts and panels before operating.

9. Reconnect power.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

RANGE HOOD USE

Pull filter toward front.

Set the filter face down on a protective cover such as a towel.

Install charcoal filter on rear of metal filter with metal wires

provided in filter packaging.

A. Metal wires

B. Charcoal filter

C. Metal filter

The canopy hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

Range Hood Control Panel

The range hood controls are located on the underside of the

canopy.

o ©@©Q ]

A B C D E

A. Indicator light

B. Light button

C. Low speed button

D. Medium speed button

E. High speed button

Operating the light

1. Press the "B" button to turn on the light.

2. Press the "B" button again to turn off the light.

Operating the blower and adjusting blower speed

1. Press the "C" button for low speed, the "D" button for

medium speed or the "E" button for high speed.

2. Press the "C" button to turn off the blower.

RANGE HOOD CARE

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Check that lights are cool before cleaning the hood.

Exterior surfaces

Clean the range hood with a mild detergent and soft cloth. Do not

use abrasive cleanser or steel-wool pads.

Metal grease filters

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean. Drain water

through edge holes and let each filter dry thoroughly before

replacing it.

To remove metal filters:

1. Turn off blower and lights. Check that the halogen lamp is

cool.

2. Push handle toward the rear and pull downward.

3. Pull filter toward the front.

To replace the metal grease filter:

1. Insert back edge of filter into rear channel of the filter

opening.

2. Push handle toward the rear and push filter up.

3. Pull filter toward the front and insert into front channel.

Charcoal Filters - For non-vented (recirculating)

installations

The charcoal filters capture unpleasant cooking odors. They can

be cleaned and reactivated. With normal use the filter should be

cleaned every second month (when using the hood 2.5 hours per

day, on average).

Clean the filter in the dishwasher using normal detergent and

choosing the highest temperature setting. Wash the filter

separately. To reactivate the filter, the filter should be dried in

an oven for 10 minutes with a maximum temperature of

210°F (100°C).

After approximately 3 years of use, the charcoal filter should be

replaced. See "Assistance or Service" section to order

replacement charcoal filters.

To replace charcoal filter:

1. Turn off blower and lights. Check that range hood is off and

halogen lamp is cool.

2. Remove the metal grease filters by pushing handle toward

the rear and pull downward.

3. Pull filter toward front.

4. Set the filter face down on a protective cover such as a towel.

5. Remove metal wires and clean or discard charcoal filter.

6. Install cleaned or replacement charcoal filter on rear of metal

filter with metal wires provided in filter packaging.

To replace the metal grease filters:

1. Insert back edge of filter into rear track of the filter opening.

2. Push handle toward the rear and push filter up.

3. Pull filter toward the front and insert into front track.

Replacing a halogen lamp

Turn off the range hood and allow the halogen lamps to cool.

Replace bulb by using a tissue to handle bulb or while wearing

cotton gloves. Do not touch bulb with bare fingers.

If new lights do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Use a flat-blade screwdriver and gently pry the light cover

loose.

3. Remove the lamp and replace with a 12-volt, 20-watt

maximum, halogen lamp made for a G-4 base.

4. Replace the light cover.

5. Reconnect power.

WIRING DIAGRAM

SW1 SW2 SW3 SW4

Light ON 1 x x x

L N $ Light OFF 0 x x x

___ Vel 1 x 1 0 0

Vel 2 x 1 1 0

Vel 3 x 1 x 1

SWx

[]

_iI O _Ol_l • 1-3 3-5

oNE]N N

SW1 SW2 SW3 SW4

BE07AA

t YB

OHM RESISTANCE (Ohm)

BETWEEN TERMINALS

from 5.6 to 11.8 ohm

MOTOR

SPEED

CONNECTION

TO TERMINAL

blue(3)-white(7)

blue(3)-red(6)

blue(3(-green(5)

blue(3)-blank(4)

Y Y

ASSISTANCEOR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified parts replacement parts in your area, call us or your

nearest Whirlpool designated service center.

!_ _ _'_E _ _ _

f" USA

Call the Whirlpool Customer eXperience Center

toll free: 1-800-253-1301.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors and service

companies. Whirlpool designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company inyour

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Accessories List

Charcoal Filter Kit

Part Number 4396850

Call the Whirlpool Canada LP Customer Interaction Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Customer Interaction Centre

Whirlpool Canada LP

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

WHIRLPOOLCORPORATIONMAJOR APPLIANCEWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

This limited warranty applies only when the major appliance is used in the country in which it was purchased.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was

purchased.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if

another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help

can be found by checking the "Assistance or Service" section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,

call 1-800-807-6777. 12/05

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELA HOTTEDECUlSlNIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves & vous

et & d'autres.

Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

iMPORTANTES iNSTRUCTiONS DE SECURITE

AVERTISSEIVlENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r6tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r6tablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tous les codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil & gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op6rations de d6coupage et de perqage dans un mur

ou un plafond, veiller & ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les syst_mes d'6vacuation doivent toujours d6charger I'air

&I'ext6rieur.

IVilSE EN GARDE : Cet appareil est con_:u uniquement

pour la ventilation g6n6rale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller & acheminer I'air

aspir6 par un conduit jusqu'& I'ext6rieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R¢:DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MI2TALLIQUES.

AVERTISSEIVIENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati@e graisseuse pourrait

provoquer une inflammation et la g6n6ration de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets & flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR REDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRF:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINIt_RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust6, une t61e &

biscuits ou un plateau m6tallique POUR ¢:TOUFFER LES

FLAMMES, puis 6teindre le brt_leur & gaz ou 61ectrique.

VEILLER A EVITER LES BRULURES. Si les flammes ne

s'6teignent pas imm6diatement, EVACUER LA PIt_CE ET

APPELER LES POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMME - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si:

- IIs'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- IIs'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar6.

- Les pompiers ont @6 contact6s.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op6ration de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

[] AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse & semi-

conducteurs.

CONSERVEZ CES iNSTRUCTiONS

EXIGENCESD'INSTALLATION

Ou c g® ®

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiques ici.

Outillage n_cessaire

• Niveau

• Perceuse avec forets de 11¼"(3 cm), 3/8"(9,5 mm),

%4" (2,75 mm) et 1/8"(3 mm)

• Crayon

• Pince a denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet a calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides pour conduit d'evacuation

• Scie sauteuse ou scie a guichet

• Tournevis a lame plate

• Cisaille de ferblantier

• Tournevis Phillips

Pi_ces n_cessaires

• Conduit de dia. 1/2"

• Deux serre-c&ble de 1/2"(12,7 mm) - homologation UL

ou CSA

• 3 connecteurs de fils homologues UL

• 1 bouche de decharge (decharge a travers lemur ou

travers le toit)

• Conduit d'evacuation metallique

• Ensemble de filtre a charbon (piece n° 4396850) - seulement

pour une installation sans decharge a I'exterieur (recyclage).

Voir la section "Assistance ou service" pour placer une

commande.

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• Hotte avec ventilateur, lampes et raccord de transition avec

clapets anti-reflux installes

• Deflecteur pour installation sans decharge a I'exterieur

(recyclage)

• Sachet de documents

• Filtre- installe sur la hotte

• 2visde5x35mm

• 4visde4x8mm

• 2visde6x70mm

• 6 vis de 3,5 x 6,5 mm

• 4 vis de 2,9 x 6,5 mm

• 2 chevilles d'ancrage de diametre 10 x 70

• Gabarit de montage

• Bride de support inferieure

• Bride de cache-conduit

• 2 cornieres

• 2 crochets de montage

• Cache-conduit- 2 pieces

• Garniture esthetique

• Bandes de caoutchouc (1 ou 2, coupees selon le besoin)

• 4 pitons de caoutchouc

IMPORTANT • Observer les dispositions de tous les codes et

reglements en vigueur.

Confier I'installation de la hotte &un technicien qualifie. C'est

I'installateur qu'incombe la responsabilite de respecter les

distances de separation exigees, specifiees sur la plaque

signaletique de I'appareil. La plaque signaletique de I'appareil est

situee derriere le filtre, sur la paroi arriere de la hotte.

On doit toujours installer la hotte a distance des sources de

courant d'air (fenatres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards; ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

On doit disposer d'une prise de courant electrique reliee a la

terre. Voir la section "Specifications electriques".

La hotte est configuree a I'usine pour la decharge a travers le toit

ou un mur.

Pour une installation sans decharge a I'exterieur (recyclage), voir

"Installation sans decharge a I'exterieur (recyclage)" a la section

"Raccordement du circuit d'evacuation". L'ensemble Filtre

charbon (piece numero 4396850) est disponible chez votre

marchand ou chez un distributeur de pieces autorise.

On doit assurer I'etancheite au niveau de chaque ouverture

decoupee dans le plafond ou un mur traverse par I'equipement

de la hotte.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, Titre 24, HUD, partie 280);

Iorsque cette norme n'est pas applicable, I'installation doit

satisfaire aux criteres de la plus recente edition de la norme

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, ou

des codes et reglements Iocaux.

• 3visdeM4x35mm

Dimensions du produit

-._ 11%o" __ _ 13%6"

_ (28,7 crn) >v _ (33,5 c m)

1" (2,5 crn) rnin.* |._._ I

(111,6cm) I I I I

max.

I_ 36" _ (13cm)

(91,4 crn) _._.

*IMPORTANT : Pour une installation sans decharge & I'exterieur

(recyclage), la dimension minimale est de 6" (15,2 cm).

Dimensions & respecter Iors de I'installation

12"

10 W' (26,7 crn)".

Placard

lateral

i (63,_"cm)

I 30" (76,2 crn) rnin.

I entre mabase de mahotte

Axe central

et la surface de cuisson

du cable passage

d'alimentation et

du conduit

d'_vacuation

• Le systeme d'evacuationdoitdechargerl'aira l'exterieur,

exceptepour lesinstallationssans decharge a l'exterieur

(recyclage).

• Ne pas terminer le conduit d'evacuation dans un grenier ou

dans un autre espace ferm&

• Ne pas utiliser une bouche de decharge murale de

4" (10,2 cm) normalement utilisee pour un equipement de

buanderie.

Utiliser un conduit m_tallique uniquement. Un conduit en

m_tal rigide est recommand& Ne pas utiliser de conduit de

plastique ou de metal tr_s m_nce.

Le systeme d'evacuation doit comporter un clapet. Si la

bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte de

cuisiniere.

Pour un fonctionnement efficace et silencieux :

• Utiliser autant que possible des sections droites et minimiser

le nombre de coudes.

Ne pas utiliser plus de trois coudes &90°.

Veiller & ce qu'il y ait une section droite de conduit de

24" (61 cm) ou plus entre deux coudes, si on doit utiliser plus

de un raccord coud&

• Ne pas installer 2 coudes ensemble.

• Au niveau de chaque jointure du conduit de decharge,

assurer I'etancheite avec des brides.

• Autour de la bouche de decharge & I'exterieur, assurer

I'etancheite avec un produit de calfeutrage.

• La taille du conduit doit _tre uniforme.

Installations pour r_gions _ climat froid

On doit installer un clapet anti-reflux additionnel pour minimiser

le reflux d'air froid. Un element non m_tallique d'isolation

thermique doit _tre installe pour minimiser la conduction des

temperatures exterieures par I'interm_diaire du conduit

d'evacuation. Le clapet anti-reflux doit _tre place du c6te air froid

par rapport &I'element d'isolation thermique.

L'element d'isolation thermique doit _tre aussi proche que

possible de I'endroit oQ le systeme d'evacuation s'introduit dans

la partie chauffee de la maison.

Renouvellement de rair

Le code du b&timent local peut exiger I'emploi d'un systeme de

renouvellement de I'air/introduction d'air d'appoint, Iors de

I'utilisation d'un systeme d'aspiration de debit superieur & une

valeur (pieds cubes par minute) specifiee. Le debit specifie, pieds

cubes par minute, est variable d'une juridiction &une autre.

Consulter un professionnel des installations de chauffage

ventilation/climatisation au sujet des exigences specifiques

applicables dans la juridiction locale.

M_thodes d'_vacuation

Cette hotte est configuree a I'usine pour la decharge de I'air

aspire &travers le toit ou & travers un mur.

Pour I'installation, on doit utiliser un conduit de diam_tre

8" (20,3 cm) (pas fourni). La hotte comporte une ouverture de

sortie de diam_tre 8" (20,3 cm).

REMARQUE : On deconseille I'emploi d'un conduit flexible. Un

conduit flexible peut causer une retro-pression et des

turbulences de I'air, ce qui reduit considerablement la

performance.

La sortie a I'exterieur du circuit d'evacuation peut se faire &

travers le toit ou & travers un mur. Pour la sortie & travers un mur,

on doit employer un raccord coude & 90°.

D_charge par I'arri_re

Le raccord coude a 90 ° peut _tre installe imm_diatement au-

dessus de la hotte.

Installation sans d_charge & I'ext_rieur (recyclage)

S'il n'est pas possible d'evacuer lee futures et vapeurs de

cuisson & I'exterieur, on peut employer la version "installation

sans decharge & I'exterieur (recyclage)" de la hotte dotee d'un

filtre &charbon actif et du deflecteur. Les vapeurs/fum_es sont

alors recyclees &travers la grille superieure.

D_charge

travers le toit

D_charge

travers le mur

.... A

Installation sans

d_charge

I'ext_rieur

(recyclage)

A. Bouche de A. Bouche de A. D_flecteur

d_charge sur toit d_charge murale B. Conduit dia.

B. Conduit dia. B. Conduit dia. 8" (20,3 cm)

8" (20,3 cm) 8" (20,3 cm)

Calcul de la Iongueur effective du circuit d'_vacuation

Pour calculer la Iongueur effective du circuit d'evacuation

necessaire, additionner les Iongueurs equivalentes (pieds/metres)

de tous les composants utilises dans le systeme.

Composant Conduit dia. 8" (20,3 cm)

coude a 45° 2,5 pi (0,8 m)

coude &90° 5 pi (1,5 m)

La Iongueur equivalente maximum du conduit est de

50 pi (15,2 cm).

Exemple de syst_me de d_charge

Bouche de

Coude _ 90° murale

............op, d ohar o

La Iongueur maximale du circuit ne doit pas depasser

50 pi (15,2 metres), ce qui est le cas pour I'exemple suivant.

1-coudea90 ° =5pi(1,5m)

1 - bouche de decharge murale = 0 pi (0 m)

section droite de 8 pi (2,4 m) = 8 pi (2,4 m)

Longueur totale = 13 pi (3,9 m)

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur. Conserver les instructions d'installation

pour consultation par I'inspecteur des installations electriques.

C'est au client qu'incombe la responsabilite de contacter un

electricien qualifie et de veiller & ce que I'installation electrique

soit adequate et realisee en conformite avec les prescriptions de

la plus recente edition de la norme National Electrical Code,

ANSI/NFPA 70, ou de la norme CSA C22.1-94, Code canadien de

I'electricite, partie 1 et C22.2 N° 0-M91, et de tousles codes et

reglements Iocaux en vigueur.

Si les codes le permettent et si on utilise un conducteur distinct

de liaison & la terre, il est recommande qu'un electricien qualifie

verifie la qualite de la liaison & la terre.

Pour obtenir un exemplaire de la norme des codes ci-dessus,

contacter :

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• L'appareil doit _tre alimente par un circuit de 120 V,60 Hz,

CA seulement, 15 amperes, protege par fusible.

• Ne pas utiliser une tuyauterie de gaz pour le raccordement &

la terre.

• En cas de doute quanta la qualite de la liaison & la terre de la

hotte de la cuisiniere, consulter un electricien qualifi&

• Ne pas installer un fusible dans le conducteur neutre ou le

conducteur de liaison & la terre.

• La hotte doit _tre raccordee au reseau electrique uniquement

avec des conducteurs de cuivre.

• La hotte doit _tre raccordee directement au coupe-circuit

avec fusible ou au disjoncteur par I'intermediaire de c&ble &

conducteurs de cuivre, &blindage metallique flexible ou &

gaine non-metallique. IIest recommande de raccorder la

hotte sur un circuit distinct exclusif & cet appareil.

• Le calibre des conducteurs (cuivre seulement) et les

connexions doivent _tre compatibles avec la demande de

courant de I'appareil specifiee sur la plaque signaletique. La

plaque signaletique de I'appareil est situee derriere le filtre,

sur la paroi arriere de la hotte.

• Le calibre des conducteurs doit satisfaire les exigences de la

plus recente edition de la norme National Electrical Code,

ANSI/NFPA 70, ou de la norme CSA C22.1-94, Code

canadien de I'electricite, partie 1 et C22.2 N° 0-M91 et de

tous les codes et reglements en vigueur.

• Un serre-c&ble de Y_" (12,7 mm) (homologation UL ou CSA)

doit _tre installe & chaque extremite du c&ble d'alimentation

(sur la hotte et sur le boftier de distribution).

INSTRUCTIONSD'INSTALLATION

On recommande que le circuit d'evacuation soit installe avant

I'installation de la hotte.

On ne dolt couper un poteau de colombage ou une solive

que si c'est absolument necessaire. Dans ce cas, on devra

construire une structure de support appropriee.

Avant d'executer les decoupages, verifier la disponibilite d'un

espace de passage suffisant dans le plafond ou lemur pour

le conduit d'evacuation.

Avant de selectionner la hotte & installer, mesurer la hauteur

libre sous plafond et la hauteur maximum disponible sous la

hotte.

Risque du poids excessif

Utiliser deux ou plus de personnes pour d_placer et

installer la cuisini_re.

Le non=respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

A. Axe central

B. Bride de support inf_rieure

C. Vis de 5 x 35 mm

D. Ligne de r_f_rence - hauteur de montage

E. Emplacements des organes de fixation

F. Mur

1. Si possible, deconnecter la cuisiniere autonome ou

encastree, et deplacer celle-ci hors de I'espace d'installation

entre les placards, pour faciliter I'acces au mur arriere. Sinon,

placer une epaisse couverture de protection sur le plan de

travail, la cuisiniere ou la table de cuisson pour la protection

contre les dommages ou souillures.

2. Determiner la methode d'extraction & utiliser : decharge

travers lemur ou le toit, ou recyclage.

3. Selectionner une surface plane pour I'assemblage de la

hotte. Recouvrir cette surface d'un materiau de protection.

Risque du poids excessif

Utiliser deux ou plus de personnes pour d_placer et

installer la hotte de la cuisini_re.

Le non=respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

4. A I'aide de deux personnes ou plus, soulever la hotte de la

cuisiniere et la poser sur une surface de protection.

5. Determiner et marquer la position de I'axe central sur le mur

oQ la hotte sera installee.

6. Choisir une hauteur de montage - minimum 30" (76,2 cm) et

maximum suggere 36" (91,4 cm) - au-dessus de la surface de

cuisson et tracer une ligne de reference sur lemur.

7. Fixer le gabarit en place avec du ruban adhesif; aligner I'axe

central du gabarit et le bas du gabarit avec la ligne

correspondant au bas de la hotte, et avec I'axe central dej&

trace sur lemur.

8. Placer la bride de support inferieure sur le gabarit; aligner la

bride avec le rectangle trace. Marquer sur le mur &travers le

gabarit la position du centre des 3 organes de fixation.

IMPORTANT : Chaque vis dolt etre vissee dans du bois.

Enlever le gabarit.

9. Percer des avant-trous de %4" (2,75 mm) aux 2

emplacements superieurs pour la pose des vis dans du bois.

10. Determiner et marquer toutes les lignes de decoupage

necessaires sur lemur pour le passage du circuit

d'evacuation. Installer le systeme d'evacuation avant la hotte.

Voir la section "Exigences concernant I'evacuation".

11. Determiner la hauteur appropriee pour le conduit de 1/2";

percer un trou de 1W' (3,2 cm) a cet endroit.

12. Faire passer leconduit de 1/2"a travers le trou. Faire passer le

c&blage dans le conduit de 1/2"- respecter les prescriptions

des codes en vigueur (Code national de I'electricite, normes

CSA ou codes/reglements Iocaux); il faut que la Iongueur du

conduit de 1/2"et des conducteurs soit suffisante depuis le

tableau de distribution (avec fusibles ou disjoncteurs) pour

realiser facilement le raccordement dans le boffier de

connexion de la hotte.

13. Utiliser un calfeutrant pour assurer I'etancheite au niveau de

chaque ouverture.

REMARQUE : Ne pas remettre le systeme sous tension avant

d'avoir completement termine I'installation.

La page charge ...

IKEA IHW8305WS0 Guide d'installation

Marque: IKEA

Modèle: IHW8305WS0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: IKEA IHW8305WS0 Installation guide

IKEA IHW8305WS0 Guide d'installation

Ce manuel convient également à

IKEA IHW8305WS0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents