Yamaha RX-V1600 Le manuel du propriétaire

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

RX-V1600

Printed in Malaysia WF99920

RX-V1600

AV Receiver

Ampli-tuner audio-vidéo

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

GB

RX-V1600_GB-cv.fm Page 1 Friday, August 26, 2005 3:34 PM

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

18 Before moving this unit, press MASTER ON/OFF to release it

outward to the OFF position to turn off this unit, the main

room, Zone 2 and Zone 3 and then disconnect the AC power

plug from the AC wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC main supply. Voltages are:

Asia model ................................ AC 220/230–240 V, 50/60 Hz

General model.............AC 110/120/220/230–240 V, 50/60 Hz

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by MASTER ON/OFF. In this

state, this unit is designed to consume a very small

quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

1

PREPARATIONINTRODUCTION

BASIC

OPERATION

SOUND FIELD

PROGRAMS

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

English

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote controls.................. 4

Handling the remote control ...................................... 5

Opening and closing the front panel door.................. 5

CONTROLS AND FUNCTIONS ......................... 6

Front panel ................................................................. 6

Remote control........................................................... 8

Zone 2/Zone 3 remote control ................................. 10

Front panel display .................................................. 11

Rear panel ................................................................ 13

CONNECTIONS .................................................. 14

Before connecting speakers ..................................... 14

Connecting speakers ................................................ 15

Using bi-wire and bi-AMP connections .................. 19

Information on cables and jacks

used for connections............................................ 20

Connecting HDMI components............................... 23

Connecting video components................................. 24

Connecting audio components................................. 27

Connecting the antennas.......................................... 29

Connecting the power cable..................................... 30

Turning on and off this unit..................................... 30

Setting the speaker impedance................................. 31

AUTO SETUP....................................................... 32

Introduction.............................................................. 32

Optimizer microphone setup.................................... 32

Using AUTO SETUP .............................................. 33

PLAYBACK.......................................................... 36

Basic operations....................................................... 36

Additional operations............................................... 38

RECORDING ....................................................... 45

FM/AM TUNING ................................................. 46

Automatic tuning ..................................................... 46

Manual tuning.......................................................... 47

Automatic preset tuning........................................... 47

Manual preset tuning ............................................... 49

Selecting preset stations........................................... 50

Exchanging preset stations ...................................... 51

Receiving Radio Data System stations.................... 52

Changing the Radio Data System mode .................. 52

PTY SEEK function ................................................ 53

EON function........................................................... 54

EDITING SOUND FIELD PARAMETERS ......55

What is a sound field? ............................................. 55

Changing parameter settings ................................... 55

SOUND FIELD PROGRAM

DESCRIPTIONS...............................................57

For movie/video sources.......................................... 57

For music sources .................................................... 59

SOUND FIELD PARAMETER

DESCRIPTIONS...............................................60

SOUND FIELD PROGRAM

SPEAKER LAYOUTS......................................64

MANUAL SETUP.................................................68

Using MANUAL SETUP........................................ 70

Using BASIC MENU .............................................. 71

Using SOUND MENU ............................................ 74

Using INPUT MENU .............................................. 76

Using OPTION MENU ........................................... 78

ADVANCED OPERATIONS ..............................82

Selecting the OSD mode.......................................... 82

Adjusting speaker levels .......................................... 82

ADVANCED SETUP............................................83

Using ADVANCED SETUP ................................... 83

REMOTE CONTROL FEATURES ...................85

Control area ............................................................. 85

Controlling each component.................................... 86

Setting remote control codes ................................... 87

Using LEARN ......................................................... 89

Using RE-NAME .................................................... 91

Using MACRO ........................................................ 92

Using CLEAR.......................................................... 94

ZONE 2/ZONE 3 ...................................................97

Connecting the Zone 2 and

Zone 3 components ............................................. 97

Selecting Zone 2 or Zone 3...................................... 98

Controlling Zone 2 and Zone 3................................ 99

Using the control mode of

Zone 2 and Zone 3............................................. 100

HDMI ...................................................................101

What is HDMI? ..................................................... 101

Setting the HDMI parameters................................ 102

Basic HDMI operations ......................................... 102

TROUBLESHOOTING .....................................103

GLOSSARY.........................................................110

Audio information ................................................. 110

Video information.................................................. 112

Sound field program information .......................... 112

Parametric equalizer information .......................... 113

SPECIFICATIONS.............................................114

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

SOUND FIELD PROGRAMS

ADVANCED OPERATION

ADDITIONAL INFORMATION

FEATURES

2

Built-in 7-channel power amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz to 20 kHz, 8 Ω)

Front: 120 W + 120 W

Center: 120 W

Surround: 120 W + 120 W

Surround Back: 120 W + 120 W

Sound field features

◆ Proprietary YAMAHA technology for the creation of

sound fields

◆ THX Select2

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1,

DTS Neo:6 decoder, DTS 96/24

◆ Dolby Pro Logic/Dolby Pro Logic x decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated AM/FM tuner

◆ 40-station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

Radio Data System

(U.K. and Europe models only)

◆ Radio Data System tuning capability

HDMI (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or

high-definition video as well as multi-channel digital

audio

◆ Analog video to HDMI digital video up-conversion

(composite video ↔ S-video ↔ component video →

HDMI digital video) capability for monitor out

Other features

◆ YPAO (YAMAHA Parametric Room Acoustic

Optimizer) for automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ OSD (on-screen display) menus that allow you to

optimize this unit to suit your individual audio/video

system

◆ 6 or 8-channel additional input jacks for discrete

multi-channel input

◆ Short message function

◆ PURE DIRECT for pure fidelity sound with analog and

PCM sources

◆ S-video input/output capability

◆ Component video input/output capability

◆ Analog video I/P conversion from 576i to 576p

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening mode

◆ Remote control with preset remote control codes and

learning/macro capability

◆ Zone 2/Zone 3 custom installation facility

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc.

In case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Surround EX”, and the double-D symbol are

trademarks of Dolby Laboratories.

“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of

Digital Theater Systems, Inc.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

The THX logo is a trademark of THX Ltd. which may be

FEATURES

GETTING STARTED

3

INTRODUCTION

English

Please check that you received all of the following parts.

GETTING STARTED

Supplied accessories

B

CLEAR

LEARN

RE–NAME

MENU

REC

DISC SKIP

EFFECT

RETURN

DISPLAY

BAND

SRCH MODE

NIGHT

AUDI O

PURE DIRECT

ENTER

LEVEL

TITLE

SELECT

DTV DVR/VCR2VCR 1 DVD

V

-

AUX

CBL/SAT MD/TAPE

CD-R

PHONO TUNER CD

MULTI CH IN

1

2 B

THX

STANDARD SELECT EXTD SUR.

STEREO

MUSIC ENTERTAIN MOVIE

VOLUME

+

–

3421

90

+10

ENT.

5678

POWER POWER

POWER

STANDBY

AVTV

SLEEP

AUDIO SEL

A

CH

+

–

TV VOL

TV MUTE TV INPUT

MUTE

+

–

AMP

SOURCE

TV

MACROONOFF

A

SPEAKERSMEMORY

SET MENU

ON SCREEN

STRAIGHT

PRESET

A/B/C/D/E

FREQ/TEXT EON MODE PTY SEEK START

Remote control

Batteries (x6)

(AAA, R03)

AM loop antenna

Optimizer microphone

Speaker terminal

wrench

Power cable

Indoor FM antenna

(U.S.A., Canada, Asia,

General, China and

Korea models)

TUNER

1

CD

2

CD-R

3

DTV

4

CBL/SAT

5

MD/TAPE

6

VCR1

7

DVR/VCR2

8 9

0

POWER

STANDBY

++

–

A/B/C/D/E

MUTE

PRESET

VOLUME

ZONE 3ZONE 2

ID2ID1

ENT

0

DVD

V-AU X

PHONO

Zone 2/Zone 3

remote control

Indoor FM antenna

(Australia, U.K. and

Europe models)

75-ohm/300-ohm antenna

adapter (U.K. model only)

GETTING STARTED

4

• Change all of the batteries if you notice conditions such as the operation range of the remote control decreases, the indicator does not

flash, or its light or display window become dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these

different types of batteries may have the same shape and color.

• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

• Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.

■ Installing batteries

1 Press the part and slide the battery

compartment cover off.

2 Insert four supplied batteries

(AAA, R03) according to the polarity

markings on the inside of the battery

compartment.

3 Slide the cover back until it snaps into place.

■ Zone 2/Zone 3 remote control

1 Press the part and slide the battery

compartment cover off.

2 Insert two supplied batteries (AAA, R03)

according to the polarity markings (+ and –)

on the inside of the battery compartment.

3 Slide the cover back until it snaps into place.

Installing batteries in the remote controls

Notes

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the remote control code and program

any acquired functions that may have been cleared.

1

3

2

1

3

2

GETTING STARTED

5

INTRODUCTION

English

The remote control transmits a directional infrared ray.

Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– extremely low temperatures

– dusty places

When you want to use the controls behind the front panel door, open the door by gently pressing on the lower part of the

panel. Keep the door closed when not using these controls.

Handling the remote control

Notes

A

SPEAKERS

YPAO

B

MULTI CH

INPUT

AUDIO

SELECT

TONE

CONTROL

STRAIGHT

PRESET/

TUNING

MAN'L/AUTO FM

EDIT

AUTO/MAN'L EFFECT

TUNING

MODE

MEMORY

ZONE 2

ZONE ON/OFF

ZONE 3

ZONE CONTROL

FM/AM

A/B/C/D/E

SILENT CINEMA S VIDEO VIDEO L

VIDEO/AUX

AUDIO R OPTICAL

PHONES

PRESET/

TUNING

OPTIMIZER

MIC

VOLUME

PROGRAM

INPUTMAIN ZONE

PURE DIRECT

ON/OFF

MASTER

ON OFF

MULTI ZONE

30 30

B

CLEAR

LEARN

RE–NAME

ON SCREEN

SET MENU

MENU

REC

DISC SKIP

EFFECT

RETURN

DISPLAY

STRAIGHT

BAND

A/B/C/D/E

NIGHT

AUDIO

PURE DIRECT

ENTER

LEVEL

TITLE

SELECT

DTV DVR/VCR2VCR 1 DVD

V

-

AUX

CBL/SAT MD/TAPE

CD-R

PHONO TUNER CD

MULTI CH IN

B

THX

STANDARD SELECT EXTD SUR.

STEREO

MUSIC ENTERTAIN MOVIE

VOL

+

–

3421

90

+10

ENT.

5678

POWER POWER POWER

SYSTEM

STANDBY

AVTV

SLEEP

AUDIO SEL

A

CH

+

–

TV VOL

TV MUTE TV INPUT

MUTE

+

–

AMP

SOURCE

TV

MACROONOFF

A

SPEAKERS

PRESET

FREQ/TEXT EON MODE PTY SEEK START

Approximately 6 m

Opening and closing the front panel door

To open, press gently on the lower part of the panel.

CONTROLS AND FUNCTIONS

6

1 MASTER ON/OFF

Press inward to the ON position.

• Turns on this unit.

• Turns on the main room.

• Sets Zone 2 and Zone 3 to the standby mode.

Press again to release it outward to the OFF position.

• Turns off this unit.

• Turns off the main room, Zone 2 and Zone 3.

See page 30 for details.

2 MAIN ZONE ON/OFF

Turns on this unit only or sets it to the standby mode.

y

In the standby mode, this unit consumes a small quantity of

power.

• When you turn on this unit, there will be a 6 to 7 second delay

before this unit can reproduce sound.

• This button is operational only when MASTER ON/OFF is

pressed inward to the ON position.

3 INPUT selector

Selects the desired input source.

4 AUDIO SELECT

Toggles the priority for the type of audio input jack

between AUTO, HDMI, COAX/OPT and ANALOG when

one component is connected to two or more input jacks on

the rear panel (see page 43).

5 MULTI CH INPUT

Selects the input source connected to the MULTI CH

INPUT jacks. When selected, the MULTI CH INPUT

source takes priority over the input source selected with

the INPUT selector (or the input selector buttons on the

remote control).

6 A/B/C/D/E

Selects one of the 5 preset station groups (A to E) when

TUNER is selected as the input source (see page 50).

7 PRESET/TUNING l / h

Selects the preset station number (1 to 8) when TUNER is

selected as the input source and the colon (:) is displayed

next to the band indication in the front panel display.

Selects the tuning frequency when TUNER is selected as

the input source and the colon (:) is not displayed in the

front panel display.

See pages 46 to 51 for details.

CONTROLS AND FUNCTIONS

Front panel

A

SPEAKERS

YPAO

B

MULTI CH

INPUT

AUDIO

SELECT

TONE

CONTROL

STRAIGHT

PRESET/

TUNING

MAN'L/AUTO FM

EDIT

AUTO/MAN'L EFFECT

TUNING

MODE

MEMORY

ZONE 2

ZONE ON/OFF

ZONE 3

ZONE CONTROL

FM/AM

A/B/C/D/E

SILENT CINEMA S VIDEO VIDEO L

VIDEO/AUX

AUDIO R OPTICAL

PHONES

PRESET/

TUNING

OPTIMIZER

MIC

VOLUME

PROGRAM

INPUTMAIN ZONE

PURE DIRECT

ON/OFF

MASTER

ON OFF

MULTI ZONE

ILMKJHG

21 3 45 6 7 8 90AB C E F

D

(General model)

Notes

CONTROLS AND FUNCTIONS

7

INTRODUCTION

English

8 Front panel display

Shows information about the operational status of this

unit.

9 PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h

between selecting preset station numbers and tuning when

TUNER is selected as the input source (see pages 46 to

51).

0 FM/AM

Switches the reception band (FM or AM) when TUNER is

selected as the input source (see page 46).

The frequency of the previously received station is automatically

recalled.

A MEMORY (MAN’L/AUTO FM)

Stores a station in the memory when TUNER is selected

as the input source. Hold down for more than 3 seconds to

start automatic preset tuning (see page 47).

B TUNING MODE (AUTO/MAN’L), DISPLAY

Switches the tuning mode between automatic (the AUTO

indicator is turned on) and manual (the AUTO indicator is

turned off) when TUNER is selected as the input source.

C STRAIGHT (EFFECT)

Turns the sound field programs on or off. When

STRAIGHT is selected, 2-channel or multi-channel input

signals are output directly from the respective speakers

without effect processing.

D Remote control sensor

Receives infrared signals from the remote control.

E TONE CONTROL

Use to adjust the balance of bass and treble for the front

left and right and center channels (see page 38).

F PURE DIRECT

Turns on or off the PURE DIRECT mode (see page 41).

The indicator around the button lights up when the unit is in the

PURE DIRECT mode.

G OPTIMIZER MIC jack

Use to connect the supplied optimizer microphone to run

AUTO SETUP (see page 32).

H SPEAKERS A/B

Turn on or off the set of front speakers connected to the

SPEAKERS A and/or B terminals on the rear panel each

time the corresponding button is pressed.

I PHONES (SILENT CINEMA) jack

Outputs audio signals for private listening with

headphones.

• When you connect headphones, no signals are output at the

PRE OUT jacks or to the speakers.

• All Dolby Digital and DTS audio signals are mixed down to 2-

channel stereo (front left and right channels).

J VIDEO AUX jacks

Input audio and video signals from an external source such

as a game console. To reproduce source signals at these

jacks, select V-AUX as the input source.

K MULTI ZONE buttons

ZONE 2 ON/OFF

Turns on Zone 2 only or sets it to the standby mode.

See page 30 for details.

This button is operational only when MASTER ON/OFF is

pressed inward to the ON position.

ZONE 3 ON/OFF

Turns on Zone 3 only or sets it to the standby mode.

See page 30 for details.

This button is operational only when MASTER ON/OFF is

pressed inward to the ON position.

ZONE CONTROL

Switches the zone you want to control between the

main unit, Zone 2 and Zone 3 (see page 99).

After you press ZONE CONTROL, the indicator for

the currently selected zone flashes in the front panel

display for approximately 5 seconds. While the

indicator is flashing, perform the desired operation.

L PROGRAM selector

Use to select sound field programs or adjust the balance of

bass and treble in conjunction with TONE CONTROL.

M VOLUME

Controls the volume level of all audio channels.

This does not affect the OUT (REC) level.

Note

Notes

Note

CONTROLS AND FUNCTIONS

8

This section describes the function of each control on the

remote control used to control this unit. Set AMP/

SOURCE/TV to AMP to operate this unit. To operate

other components, see “REMOTE CONTROL

FEATURES” on page 85.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 Transmission indicator

Flashes while the remote control is sending infrared

signals.

3 Input selector buttons

Select the input source and change the control area.

Set AMP/SOURCE/TV to SOURCE and then press

TUNER to select TUNER as the input source.

4 Display window

Shows the name of the selected input source that you can

control.

5 LEVEL, BAND

Selects the speaker you want to adjust the speaker output

level for when AMP/SOURCE/TV is set to AMP

(see pages 82).

Switches the reception band between FM and AM when

AMP/SOURCE/TV is set to SOURCE and TUNER is

selected as the input source.

6 Cursor buttons k / n / l / h, ENTER

Selects and adjusts the DSP program parameters or OSD

menu items when AMP/SOURCE/TV is set to AMP.

Press l / h to select a preset station group (A to E) and

k / n to select a preset station number (1 to 8) when

AMP/SOURCE/TV is set to SOURCE and TUNER is

selected as the input source.

7 RETURN

Returns to the upper or the previous directory in the OSD

menu.

8 Sound field program / numeric buttons

Select sound field programs when AMP/SOURCE/TV is

set to AMP.

Use SELECT to play back 2-channel sources in the multi-

channel format (see page 40).

Use EXTD SUR. to switch between 5.1 and 6.1/7.1

channel playback of multi-channel software (see page 39).

Use numbers 1 to 8 to select preset stations when AMP/

SOURCE/TV is set to SOURCE and TUNER is selected

as the input source.

9 MACRO ON/OFF

Turns on or off the macro function (see page 93).

0 MACRO

Programs a series of operations to be controlled with a

single button (see page 92).

Remote control

B

CLEAR

LEARN

RE–NAME

MENU

REC

DISC SKIP

EFFECT

RETURN

DISPLAY

BAND

NIGHT

AUDIO

PURE DIRECT

ENTER

LEVEL

TITLE

SELECT

DTV DVR/VCR2VCR 1 DVD

V

-

AUX

CBL/SAT MD/TAPE

CD-R

PHONO TUNER CD

MULTI CH IN

1

2 B

THX

STANDARD SELECT EXTD SUR.

STEREO

MUSIC ENTERTAIN MOVIE

VOLUME

+

–

3421

90

+10

ENT.

5678

POWER POWER

POWER

STANDBY

AVTV

SLEEP

AUDIO SEL

A

CH

+

–

TV VOL

TV MUTE TV INPUT

MUTE

+

–

AMP

SOURCE

TV

MACROONOFF

A

SPEAKERSMEMORY

PRESET

SET MENU

ON SCREEN

FREQ/TEXT

EON STARTMODE PTY SEEK

STRAIGHT

A/B/C/D/E

FREQ/TEXT EON MODE PTY SEEK START

S

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

1

2

3

4

5

6

7

8

9

0

(U.K. and Europe models)

CONTROLS AND FUNCTIONS

9

INTRODUCTION

English

A STANDBY

Sets this unit, Zone 2 and Zone 3 to the standby mode (see

page 30).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

B POWER

Turns on this unit, Zone 2 and Zone 3 (see page 30).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

C AUDIO SEL

Toggles the priority for the type of audio input jack

between AUTO, HDMI, COAX/OPT and ANALOG when

one component is connected to two or more input jacks on

the rear panel (see page 43).

D SLEEP

Sets the sleep timer.

E MULTI CH IN

Selects MULTI CH INPUT when using an external

decoder, etc.

F SELECT k / n

Selects another input source that you can control

independently of the input source selected with the input

selector buttons.

G VOLUME +/–

Increases or decreases the volume level.

H AMP/SOURCE/TV

Selects the component you want to control with the

remote control.

AMP

Set to this position to operate this unit.

SOURCE

Set to this position to operate the component selected with

an input selector button.

TV

Set to this position to operate the television assigned to

either DTV or PHONO.

If televisions are assigned to both DTV and PHONO, the one

assigned to DTV takes priority and gets operated when AMP/

SOURCE/TV is set to TV.

y

To set the remote control codes for other components, see

page 87.

I MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level.

J PURE DIRECT

Turns on or off the PURE DIRECT mode (see page 41).

K SET MENU

Enters or exits the SET MENU mode.

L NIGHT

Turns on or off the night listening modes (see page 41).

M ON SCREEN

Selects the display mode of the on-screen display (OSD)

that appears on your monitor (see page 82).

N STRAIGHT (EFFECT)

Switches the sound field programs off or on. When

STRAIGHT is selected, 2-channel or multi-channel input

signals are output directly from their respective speakers

without effect processing.

O SPEAKERS A/B

Turns on or off the set of front speakers connected to the

SPEAKERS A and/or B terminals on the rear panel each

time the corresponding button is pressed.

P RE-NAME

Changes the name of the input source in the display

window (see page 91).

Q CLEAR

Clears remote control codes or functions acquired from

the learn, macro and rename features (see page 94).

R LEARN

Programs remote control codes or functions from other

remote controls (see page 89).

S Radio Data System tuning buttons

(U.K. and Europe models only)

These buttons are operational only when TUNER is

selected as the input source.

FREQ/TEXT

Switches the Radio Data System display between the

PS mode, PTY mode, RT mode, CT mode (if the

station offers the corresponding data services) and the

frequency display (see page 52).

PTY SEEK MODE

Sets this unit to the PTY SEEK mode (see page 53).

PTY SEEK START

Starts searching for a station after the desired program

type has been selected in the PTY SEEK mode

(see page 53).

EON

Selects a radio program type (NEWS, INFO,

AFFAIRS, SPORTS) tune in automatically

(see page 54).

Note

CONTROLS AND FUNCTIONS

10

This section describes the function of each control on the

Zone 2/Zone 3 remote control used to control Zone 2 or

Zone 3.

1 Input selector buttons

Select the desired input source of Zone 2 or Zone 3 and

change the control area.

2 PRESET +/–

Selects the preset station number (1 to 8) when TUNER is

selected as the input source or Zone 2 or Zone 3.

3 A/B/C/D/E

Selects the preset station group (A to E) when TUNER is

selected as the input source or Zone 2 or Zone 3.

4 ID1/ID2 switch

Switches the remote control ID between ID1 and ID2

(see page 88).

5 POWER

Turns on Zone 2 or Zone 3.

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

6 STANDBY

Sets Zone 2 or Zone 3 to the standby mode.

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

7 VOLUME +/–

Increases or decreases the volume level or Zone 2 or

Zone 3.

8 MUTE

Mutes the sound of Zone 2 or Zone 3.

Press again to restore the audio output to the previous

volume level.

9 ZONE 2/ZONE 3 switch

Switches between the operation mode of Zone 2 and that

of Zone 3.

Zone 2/Zone 3 remote control

TUNER

1

CD

2

CD-R

3

DTV

4

CBL/SAT

5

MD/TAPE

6

VCR1

7

DVR/VCR2

8 9

0

POWER

STANDBY

+

–

+

–

A/B/C/D/E

MUTE

PRESET

VOLUME

ZONE 3ZONE 2

ID2ID1

ENT

0

DVD

V-AUX

PHONO

1

3 8

2

7

6

5

4

9

(U.K. and Europe models)

Note

CONTROLS AND FUNCTIONS

11

INTRODUCTION

English

The XM indicator is only applicable to the U.S.A. model.

1 YPAO indicator

Lights up when the AUTO SETUP procedure is in

progress and when the AUTO SETUP speaker settings are

used without any modifications.

2 HDMI indicator

Lights up when HDMI components are assigned to HDMI

IN 1 and HDMI IN 2 jacks and they are recognized by this

unit (see page 76).

Turns off when no HDMI component is assigned to the

either HDMI IN 1 or HDMI IN 2 jack or when no HDMI

component is recognized by this unit although they are

assigned to the HDMI IN jacks (see page 76).

See page 101 for details.

3 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

program.

4 Decoder indicators

When any of the decoders of this unit operate, the

respective indicator lights up.

5 Input source indicators

Light up when the corresponding input source is selected.

6 VOLUME level indicator

Indicates the volume level.

7 MUTE indicator

Flashes while the MUTE function is on.

8 AUTO indicator

Lights up when this unit is in the automatic tuning mode.

9 STEREO indicator

Lights up when this unit is receiving a stereo signal for an

FM stereo broadcast while the AUTO indicator is lit.

0 TUNED indicator

Lights up when this unit is tuned into a station.

A MEMORY indicator

Flashes to indicate that a station can be stored.

B Headphones indicator

Lights up when headphones are connected.

C SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 38).

D SP A B indicators

Light up according to the set of front speakers selected.

Both indicators light up when both sets of front speakers

are selected or when bi-wiring.

E VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active

(see page 43).

F Sound field indicators

Light up to indicate the active DSP sound fields.

G HiFi DSP indicator

Lights up when you select a HiFi DSP sound field

program.

H PCM indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

I DSD indicator

Lights up when this unit is reproducing DSD (direct

stream digital) digital audio signals.

J Multi-information display

Shows the name of the current sound field program and

other information when adjusting or changing settings.

Front panel display

Note

96

24

MATRIX

DISCRETE

VIRTUAL

CINEMA

SILENT

HOLD

EON

CT

RT

PTY

PS

SLEEP

NIGHT

ZONE3

ZONE2

PTY

STEREO

AUTO

TUNED

MEMORY

HiFi DSP

YPAO

V-AUX

A B

SP

MUTE

VOLUME

LFE

96/24

LL C R

SL SB SR

dB

DIGITAL

PCM

DSD

EX

PL x

CS

VCR 1

DTV DVD CD-R CD

XM

TUNERPHONO

MD/TAPECBL/SATDVR/VCR 2

123 4 5 6 7 890A

QOPNMLKJHGFEDCB

I

(U.K. and Europe models)

Presence DSP sound field

Listening position

Left surround

DSP sound field

Right surround

DSP sound field

Surround/surround back DSP sound field

CONTROLS AND FUNCTIONS

12

K 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

L LFE indicator

Lights up when the input signal contains an LFE signal.

M Input channel and speaker indicators

Input channel indicators

Indicate the channel components of the current digital

input signal.

Presence and surround back speaker

indicators

Light up according to the number of presence and

surround back speakers set for PRESENCE SP

(see page 72) and SB L/R SP (see page 72) in

MANUAL SETUP when TEST TONE in MANUAL

SETUP is set to ON (see page 74).

y

You can make settings for the presence and surround back

speakers automatically by running AUTO SETUP

(see page 32) or manually by adjusting settings for

PRESENCE SP (see page 72) and SB L/R SP (see page 72)

in MANUAL SETUP.

N ZONE 2/ZONE 3 indicators

Light up when Zone 2 or Zone 3 is turned on.

O NIGHT indicator

Lights up when you select a night listening mode.

P SLEEP indicator

Lights up while the sleep timer is on.

Q Radio Data System indicators

(U.K. and Europe models only)

The name of the Radio Data System data offered by

the currently received Radio Data System station

lights up.

EON

Lights up when a Radio Data System station that

offers the EON data service is being received.

PTY HOLD

Lights up while searching for stations in the PTY

SEEK mode.

LL C R

SL SB SR

CONTROLS AND FUNCTIONS

13

INTRODUCTION

English

1 DIGITAL OUTPUT jacks

See pages 24, 25 and 27 for connection information.

2 DIGITAL INPUT jacks

See pages 24, 25 and 27 for details.

3 Video component jacks

See pages 24 and 25 for connection information.

4 Audio component jacks

See pages 24, 25 and 27 for connection information.

5 CONTROL OUT jacks

These are control expansion terminals for factory use only.

6 WRENCH HOLDER

Use to hook the supplied speaker terminal wrench when

not in use (see page 16).

7 Antenna terminals

See page 29 for connection information.

8 VOLTAGE SELECTOR

(Asia and General models only)

See page 30 for detailed information.

9 AC OUTLETS

Use to supply power to your other A/V components

(see page 30).

0 AC IN

Use this inlet to plug in the supplied power cable

(see page 30).

A HDMI IN/OUT connectors

See page 101 for connection information.

B RS-232C terminal

This is a control expansion terminal for factory use only.

Consult you dealer for details.

C ZONE 2/ZONE 3 OUTPUT jacks

See page 97 for details.

D MULTI CH INPUT jacks

See page 26 for connection information.

E PRE OUT jacks

See page 28 for connection information.

F REMOTE IN/OUT jacks

See page 97 for details.

G Speaker terminals

See page 15 for connection information.

H PRESENCE/ZONE 2(3) speaker terminals

See page 17 for connection information.

Rear panel

SPEAKERS

FRONT

SURROUND

FRONT

CENTER

PRE OUT

SUBWOOFER

SURROUND BACK/PRESENCE

SURROUND/ZONE 2(3)

SPEAKER IMPEDANCE

SURROUND BACK

SINGLE

CENTER

SINGLE

(SB)

R

L

R

L

R

L

R

L

R

L

R

L

R

L

MONITOR OUT

AUDIOVIDEO

S VIDEO

DVD

DTV

CBL/

SAT

VIDEO

IN

OUT

DVR/VCR 2

VCR 1

ZONE

2

IN

CENTERSUBWOOFER

MULTI CH INPUT

OUTPUT

AUDIO

(PLAY)

IN

(PLAY)

IN

OUT

(REC)

OUT

(REC)

CD-R

MD/TAPE

CD

PHONO

SURROUND

TUNER

IN 1

IN 2

OUT

FM ANT

75Ω

UNBAL.

AM ANT

GND

DIGITAL

OUTOUT

DIGITAL INPUT

OPTICAL

MD/TAPE

CD-R

DVD

DTV

CBL/SAT

CD

CD DVD

COAXIAL

+

–

+

–

+

–

+

––

–

+

–

A

B

RS-232C

HDMI

DVR/

VCR 2

CONTROL OUT

REMOTE

GND

WRENCH

HOLDER

IN

OUT

21

COMPONENT VIDEO

PR

MONITOR OUT

PBY

DVD

DTV

CBL/

SAT

+12V 15mA MAX.

PRESENCE/ZONE 2(3)

ZONE

3

FRONT(6CH)/SB(8CH)

AC OUTLETS

AC IN

SWITCHED

50W MAX.TOTAL

812 3 4 56 7 90

HGFEDCBA

VOLTAGE

SELECTOR

(General model)

CONNECTIONS

14

The speaker layout below shows the standard ITU-R

*

speaker setting. You can use it to enjoy CINEMA DSP,

multi-channel audio sources and THX.

*

ITU-R is the radio communication sector of the ITU

(International Telecommunication Union).

Front speakers (FR and FL)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Align the front

face of the center speaker with the front face of your video

monitor. Place the speaker centrally between the front

speakers and as close to the monitor as possible, such as

directly over or under it.

Surround speakers (SR and SL)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m above the

floor.

Surround back speakers (SBR and SBL)

The surround back speakers supplement the surround

speakers and provide for more realistic front-to-back

transitions. Place these speakers directly behind the

listening position and at the same height as the surround

speakers. They should be positioned at least 30 cm apart.

Ideally, they should be positioned at the same width as the

front speakers.

Subwoofer

The use of a subwoofer, such as the YAMAHA Active

Servo Processing Subwoofer System, is effective not only

for reinforcing bass frequencies from any or all channels,

but also for high fidelity reproduction of the LFE (low-

frequency effect) channel included in Dolby Digital and

DTS software. The position of the subwoofer is not so

critical, because low bass sounds are not highly

directional. But it is better to place the subwoofer near the

front speakers. Turn it slightly toward the center of the

room to reduce wall reflections.

Presence speakers (PR and PL)

Presence speakers supplement the sound from the front

speakers with extra ambient effects produced by CINEMA

DSP (see page 57). These effects include sounds that

filmmakers intend to locate a little farther back behind the

screen in order to create more theater-like ambience. Place

these speakers at the front of the room about 0.5 – 1 m

outside the front speakers, facing slightly inwards, and

about 1.8 m above the floor.

Surround back and presence speakers do not output sound

simultaneously. You can set to prioritize either set of speakers

using the PRIORITY parameter in MANUAL SETUP (see

page 72).

CONNECTIONS

Before connecting speakers

More than 30 cm

60˚

30˚

PL

PR

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

1.8 m

Note

15

CONNECTIONS

PREPARATION

English

■ Di-pole speaker layout

Either di-pole or direct radiating speaker types can be used

for THX surround. If you choose di-pole speakers, please

place the surround and surround back speakers according

to the speaker layout below.

Be sure to connect the left channel (L), right channel (R),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

• If you will use 6 ohm speakers, be sure to set this unit’s speaker

impedance setting to 6 ohms before using (see page 31). If you

will use 8 ohm speakers, use this unit’s initial setting for

speaker impedance.

• Before connecting the speakers, make sure that this unit is

disconnected from the power source.

• Do not let the bare speaker wires touch each other or do not let

them touch any metal part of this unit. This could damage this

unit and/or speakers.

• Use magnetically shielded speakers. If this type of speaker still

creates interference with the monitor, place the speakers away

from the monitor.

A speaker cord is actually a pair of insulated cables running side

by side. One cable is colored or shaped differently, perhaps with a

stripe, groove or ridges. Connect the striped (grooved, etc.) cable

to the “+” (red) terminals on this unit and your speaker. Connect

the plain cable to the “–” (black) terminals.

■ Connecting to the speaker terminals

FRONT terminals

Connect one or two speaker systems to these terminals.

If you use only one speaker system, connect it to either of

the FRONT A or B terminals.

The Canada model cannot output to two pairs of speaker systems

simultaneously.

CENTER terminals

Connect a center speaker to these terminals.

SURROUND ZONE 2(3) terminals

Connect surround speakers to these terminals.

SUBWOOFER jack

Connect a subwoofer with a built-in amplifier, such as the

YAMAHA Active Servo Processing Subwoofer System,

to this jack.

SURROUND BACK terminals

Connect surround back speakers to these terminals.

If you only connect one surround back speaker, connect it

to the left (L) terminals.

FL

SR

SL

FR

C

SBR

SBL

: Di-pole speaker

: Direction of the di-pole speaker phase

Connecting speakers

Note

CAUTION

16

CONNECTIONS

1 Remove approximately 10 mm of insulation

from each of the speaker cables.

2 Twist the exposed wires of the cable together

to prevent short circuits.

3 Loosen the knob using the supplied speaker

terminal wrench.

4 Insert one bare wire into the hole on the side

of each terminal.

5 Tighten the knob to secure the wire using the

supplied speaker terminal wrench.

6 Hook the speaker terminal wrench onto

WRENCH HOLDER on the rear panel of this

unit when not in use.

10 mm

Red: positive (+)

Black: negative (–)

Speaker terminal wrench

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

Speaker terminal wrench

17

CONNECTIONS

PREPARATION

English

PRESENCE/ZONE 2(3) terminals

Connect presence speakers to these terminals.

You can also use these terminals to connect the Zone 2 speakers

(see page 98).

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

■ Connecting the banana plug

(With the exception of U.K., Europe and Asia models)

First, tighten the knob and then insert the banana plug

connector into the end of the corresponding terminal.

y

You can also use banana plugs with the PRESENCE/ZONE 2(3)

speaker terminals. Open the tab, then insert one banana plug

connector into the hole of each terminal. Do not attempt to close

the tabs after connecting the banana plugs.

■ Speaker layout

Refer to the following illustration as to where to place

each speaker in your listening room.

1 Subwoofer

2 Front right speaker

3 Front left speaker

4 Center speaker

5 Surround back right speaker

6 Surround back left speaker

7 Surround right speaker

8 Surround left speaker

9 Presence right speaker

10 Presence left speaker

Note

Banana plug

(With the exception of U.K., Europe and Asia models)

1

2

3

4

5

6

9

10

8

7

18

CONNECTIONS

SPEAKERS

FRONT

SURROUND

FRONT

CENTER

PRE OUT

SUBWOOFER

SURROUND BACK/PRESENCE

SPEAKER IMPEDANCE

SURROUND BACK

SINGLE

CENTER

SINGLE

(SB)

R

L

R

L

R

L

R

L

R

L

R

L

+

–

+

–

+

–

+

––

–

+

–

A

B

PRESENCE/ZONE 2(3)

Center

speaker

Front speakers (A)

Surround back speakers

LeftRight

LeftRight LeftRight

Surround speakers

Front

speakers

(B)

LeftRight

Presence speakers

• You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously. You can set

to prioritize either set of speakers using the PRIORITY parameter in MANUAL SETUP (see page 72).

• The surround back speakers output the surround back channel included in Dolby Digital EX and DTS-ES software and operate

only when the Dolby Digital EX, DTS-ES, Dolby Pro Logic x

, THX Select2, THX Music, THX Games or THX Surround EX

decoder is turned on.

• The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields

are selected.

Subwoofer with

built-in amplifier

(General model)

La page charge ...

Yamaha RX-V1600 Le manuel du propriétaire

Yamaha RX-V1600 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents