Campbell Hausfeld CE5002 Mode d'emploi

Electric Air Compressor

Operating Instructions and Parts Manual

Models: CE5002 and XC602100

IN573900 10/18

A Marmon/Berkshire Hathaway Company

EN

Please read and save these instructions. Read carefully before attempting to

assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply

with instructions could result in personal injury and/or property damage! Retain

instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to

this manual or file it for safekeeping.

REGISTER YOUR PRODUCT ONLINE NOW! www.campbellhausfeld.com/reg

READ AND FOLLOW ALL INSTRUCTIONS • SAVE THESE INSTRUCTIONS • DO NOT DISCARD

Model #: __________________________

Serial #: ___________________________

Purchase Date: _____________________

For parts, product & service information

visit www.campbellhausfeld.com

Campbell Hausfeld

100 Production Drive

Harrison, Ohio 45030

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

1

BEFORE YOU BEGIN

Description

Air compressor units are intended to provide compressed air to power pneumatic tools, operate spray guns

and supply air for pneumatic valves and actuators. The pumps supplied with these units have oil lubricated

bearings. A small amount of oil carryover is present in the compressed air stream. Applications requiring air

free of oil vapor should have the appropriate filters installed. The air compressor units are to be mounted

per the instructions provided on a solid floor. Any other use of these units will void the warranty and the

manufacturer will not be responsible for problems or damages resulting from such misuse.

QUICK REFERENCE

Recommended Oil (2 Options)

Single viscosity SAE 30 ISO100 nondetergent compressor oil. Part number ST125303AV (0.5

qt) or ST126701AV (4 qt).

10W30 synthetic oil such as Mobil 1

®

or CE0032 (1 qt).

Oil Capacity

Approximately 47.4 oz.

UNPACKING

Do not lift or move unit without appropriately rated equipment. Be sure the unit is securely

attached to lifting device used. Do not lift unit by holding onto tubes or coolers. Do not use unit

to lift other attached equipment.

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for

loose, missing or damaged parts. Check to be sure all supplied accessories are enclosed with the unit. In case

of questions, damaged or missing parts, please visit www.campbellhausfeld.com for customer assistance.

Do not operate unit if damaged during shipping, handling or use. Damage may result in

bursting and cause injury or property damage.

Required Items - Not Included

• Oil

• Concrete anchors

• Isolation pads

• Isolation valve

• Power cord/electrical disconnect

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

2

GENERAL SAFETY INSTRUCTIONS

Safety Guidelines

This manual contains information that is very important to know and understand. This information is

provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe

the following symbols.

Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death

or serious injury.

Warning indicates a potentially hazardous situation which, if not avoided, COULD result in

death or serious injury.

Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or

moderate injury.

Notice indicates important information, that if not followed, may cause damage to equipment.

IMPORTANT or NOTE: Information that requires special attention.

Safety Symbols

The following Safety Symbols appear throughout this manual to alert you to important safety hazards and

precautions.

California Proposition 65

This product can expose you to chemicals including lead, which are known to the State of

California to cause cancer and birth defects or other reproductive harm. For more information

go to www.P65Warnings.ca.gov.

You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal,

concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer,

birth defects, or other reproductive harm. Wear protective gear.

Illinois Lead Poisoning Prevention Act

CONTAINS LEAD. MAY BE HARMFUL IF EATEN OR CHEWED. COMPLIES WITH FEDERAL

STANDARDS.

Risk of

Fumes

Risk of

Pressure

Risk of Shock

MANUAL

Read

Manual

First

Top Heavy Risk of

Moving Parts

Risk of

Hot Parts

Risk of

Explosion

Risk of

Fire

Wear Eye

and Mask

Protection

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

3

Important Safety Information

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the

product described. Protect yourself and others by observing all safety information. Failure to comply with instructions

could result in personal injury and/or property damage! Retain instructions for future reference.

This manual contains important safety, operational and maintenance information. If you have any

questions, please visit www.campbellhausfeld.com for customer assistance.

BREATHABLE AIR WARNING

This compressor/pump is not equipped and should not be used “as is” to supply breathing quality

air. For any application of air for human consumption, the air compressor/pump will need to be

fitted with suitable in-line safety and alarm equipment. This additional equipment is necessary to

properly filter and purify the air to meet minimal specifications for Grade D breathing as described in

Compressed Gas Association Commodity Specification G 7.1, OSHA 29 CFR 1910. 134, and/or Canadian

Standards Associations (CSA).

DISCLAIMER OF WARRANTIES

In the event the compressor is used for the purpose of breathing air application and proper in-line

safety and alarm equipment is not simultaneously used, existing warranties shall be voided, and

Campbell Hausfeld disclaims any liability whatsoever for any loss, personal injury or damage.

General Safety

Since the air compressor and other components (material pump, spray guns, filters, lubricators, hoses, etc.)

used make up a high pressure pumping system, the following safety precautions must be observed at all

times:

• Read all manuals included with this product carefully. Be thoroughly familiar with the controls and

the proper use of the equipment.

• Follow all local electrical and safety codes as well as the United States National Electrical Codes (NEC)

and Occupational Safety and Health Act (OSHA).

• Only persons well acquainted with these rules of safe operation should be allowed to use the

compressor.

• Keep visitors away and NEVER allow children in the work area.

• Wear safety glasses and use hearing protection when operating the unit.

• Do not stand on or use the unit as a handhold.

• Before each use, inspect compressed air system and electrical components for signs of damage,

deterioration, weakness or leakage. Repair or replace defective items before using.

• Check all fasteners at frequent intervals for proper tightness.

This compressor is extremely top heavy. The unit must be bolted to the floor with isolation pads

before operating to prevent equipment damage, injury or death.

Never install a shut-off valve between the compressor pump and the tank.

Motors, electrical equipment and controls can cause electrical arcs that will ignite a

flammable gas or vapor. Never operate or repair in or near a flammable gas or vapor. Never

store flammable liquids or gases in the vicinity of the compressor.

Never operate compressor without a beltguard. This unit can start automatically without

warning. Personal injury or property damage could occur from contact with moving parts.

• Do not wear loose clothing or jewelry that will get caught in the moving parts of the unit.

Compressor parts may be hot even if the unit is stopped.

• Keep fingers away from a running compressor; fast moving and hot parts will cause injury and/or

burns.

MANUAL

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

4

GENERAL SAFETY INSTRUCTIONS (CONTINUED)

• If the equipment should start to vibrate abnormally, STOP the engine/motor and check immediately

for the cause. Vibration is generally an indication of trouble.

• To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease.

An ASME code safety relief valve with a setting no higher than 200 PSI MUST be installed in the

tank for this compressor. The ASME safety valve must have sufficient flow and pressure ratings to

protect the pressurized components from bursting.

See compressor

specifications for maximum operating pressure. Do not operate

with pressure

switch or pilot valves set higher than the maximum operating pressure.

Maximum operating pressure is 175 PSI for single stage compressors. Do not operate with

pressure switch or pilot valves set higher than 175 PSI (2-stage).

• Never attempt to adjust ASME safety valve. Keep safety valve free from paint and other

accumulations.

Never use plastic (PVC) pipe for compressed air. Serious injury or death could

result.

Never attempt to repair or modify a tank! Welding, drilling or any other modification will

weaken the tank resulting in damage from rupture or explosion. Always replace worn, cracked

or damaged tanks.

Drain liquid from tank daily.

• Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank regularly and

inspect periodically for unsafe conditions such as rust formation and corrosion.

• Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining

moisture or depressurizing the compressor system.

Spraying Precautions

Do not spray flammable materials in vicinity of open flame or near ignition sources including

the compressor unit.

• Do not smoke when spraying paint, insecticides, or other flammable substances.

• Use a face mask/respirator when spraying and spray in a well ventilated area to prevent health and fire

hazards.

• Do not direct paint or other sprayed material at the compressor. Locate compressor as far away from

the spraying area as possible to minimize overspray accumulation on the compressor.

• When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the

chemical manufacturer.

The DANGER, WARNING, CAUTION, and NOTICE notifications and instructions in this manual cannot

cover all possible conditions and situations that may occur. It must be understood by the operator that

caution is a factor which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

DO NOT DISCARD

SPECIFICATIONS

CE5002 XC602100

HP 3.5 3.5

Number of Cylinders 2 2

Number of Stages 2 2

Air Delivery @ 90 PSI 11 CFM 11 CFM

Voltage 230 Volts /

16.2 Amps

230 Volts /

16.2 Amps

Max Pressure 175 PSI 175 PSI

Oil Capacity 47.4 ounces 47.4 ounces

Tank Outlet Size 3/4 NPT 3/4 NPT

Weight 270 lbs. 270 lbs.

DIMENSIONS

CE5002 XC602100

Length 21.9 inches 21.9 inches

Width 27.5 inches 27.5 inches

Height 69.6 inches 69.6 inches

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

5

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

6

GETTING TO KNOW YOUR UNIT

Pressure Switch

Tank Pressure Gauge

Check Valve

Discharge Tube

Pump

Air Filter

ASME Safety Valve

Oil Fill Port

Breather

Belt Guard

Motor

Tank Outlet

Tank Drain Valve

Figure 1 - Unit Identification

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

7

GETTING TO KNOW YOUR UNIT

Pressure Switch - Auto/Off Switch - In the auto position, the compressor shuts off automatically when tank

pressure reaches the maximum preset pressure. After air is used from the tank and drops to a preset low

level, the pressure switch automatically turns the motor back on. In the off position, the compressor will not

operate. This switch should be in the off position when connecting or disconnecting the power from the

unit.

When the pressure switch turns the motor off you will hear air leaking out of the pressure switch unloader

valve for a short time. This releases the air pressure from the discharge tube and allows the compressor to

restart easier.

ASME Safety Valve - This valve automatically releases air if the tank pressure exceeds the preset maximum.

Discharge Tube - This tube carries compressed air from the pump to the check valve. This tube becomes very

hot during use. To avoid the risk of severe burns, never touch the discharge tube.

Check Valve - One-way valve that allows air to enter the tank, but prevents air in the tank from flowing

back into the compressor pump.

Belt Guard - Covers the belt, motor pulley and flywheel.

Tank Drain Valve - This valve is located on the bottom of the tank. Use this valve to drain moisture from the

tank daily to reduce the risk of corrosion.

Tank Pressure Gauge - Indicates amount of air pressure stored in tank.

Air Filter - Keeps large particulates out of the air flowing into the compressor.

Breather - Vent for crankcase.

Oil Fill Port - Port used to refill the oil in the pump after oil changes or when oil is low.

Pump - Cast Iron 2-Stage air compressor pump that generates compressed air.

Motor - Power source that drives the pump to create compressed air.

Tank Outlet - This is where you plumb into to get compressed air from the pressure vessel. An isolation

valve should be installed here to be able to shut off the air supply from the tank.

INSTALLATION INSTRUCTIONS

Disconnect, tag and lock out power source then release all pressure from the system before

attempting to install, service, relocate or perform any maintenance.

Do not lift or move unit without appropriately rated equipment. Be sure the unit is securely

attached to lifting device used. Do not lift unit by holding onto tubes or coolers. Do not use unit

to lift other attached equipment.

Never use the wood shipping skids for mounting the compressor.

This compressor is not intended for outdoor installation.

Preparation

Before beginning installation and/or assembly of product, make sure all parts are present. Compare parts

with package contents list. If any part is missing or damaged, do not attempt to assemble or use the

product.

Do not operate unit if damaged during shipping, handling or use. Damage may result in

bursting and cause injury or property damage.

Estimated Installation and Assembly Time: 120 minutes

Tools Required for Installation and Assembly (not included): Safety Glasses; Work Gloves; 9/16 in. Socket and

Ratchet; Tape measure; Hammer Drill and Masonry Bit; Hammer; Phillips Screwdriver; Flathead Screwdriver;

Pipe Wrench; Two Adjustable Wrenches; 1/4 in. Nut Driver, Socket or Wrench; 240 Volt, 30 Amp Double Pole

Circuit Breaker; Voltage Meter; Vibration Pads; 3/8 in. x 5 in. Wedge Anchors (for concrete installation).

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

8

INSTALLATION INSTRUCTIONS (CONTINUED)

Picking the Location

Install and operate unit at least 18 inches from any

obstructions in a clean, well ventilated area. The

surrounding air temperature should not exceed

100° F. This will ensure an unobstructed flow of air

to cool compressor and allow adequate space for

maintenance.

Do not locate the compressor air

inlet near steam, paint spray,

sandblast areas or any other source of contamination.

NOTE: If compressor operates in a hot, moist

environment, supply compressor pump with clean, dry

outside air. Supply air should be piped in from external

sources.

Tank Mounting

The tank should be bolted into a flat, even, concrete

floor or on a separate concrete foundation. Vibration

isolators should be used between the tank leg and

the floor. Model MP345700AJ isolator pads are

recommended for installation.

When using isolator pads, do not draw bolts tight.

Allow the pads to absorb vibrations. When isolators

are used, a flexible hose or coupling should be

installed between the tank and service piping.

Failure to properly install the

tank can lead to cracks at the

welded joints and possible bursting.

1. Unbolt the unit from the shipping skid. Use a

ratchet with a 9/16 in. socket. Remove the unit

from the skid. This requires at least two people -

one person to walk the unit off the skid and one

to help maintain balance so the unit does not

topple. Place the unit where you plan to install it

(at least 18 in. from any wall or surface).

2. Place pre-drilled vibration pads (sold separately)

under each foot to avoid unnecessary vibration

which could damage the unit.

Using the mounting holes and the holes of the

vibration pads as a guide, drill holes into concrete

using a 3/8 in. masonry bit. Holes drilled must be

at least 5 in. into the concrete.

3. Insert mounting bolts. Use 3/8 in. x 5 in. wedge

anchors (not included) to secure the unit. Place

nut and washer on bolt. Thread nut onto bolt

until tops are flush. Strike bolt with hammer

until nut and washer are setting on top of the

compressor foot.

Tighten nut using ratchet with a 9/16 in. socket

until anchor is set (using installation torque

specifications of bolt being used). Loosen nut

to leave a 1/16 in. (1.6 mm) gap for stress relief

during unit operation.

18 inches

Figure 2

Figure 3

Concrete Anchor

1/16 inch

(1.6 mm)

Metal Plate

Rubber

Pad

Figure 4

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

9

Piping

Never use plastic (PVC) pipe for compressed air. Serious injury or death could result.

Any tube, pipe or hose connected to the unit must be able to withstand the temperature generated and

retain the pressure. All pressurized components of the air system must have a pressure rating of 200 PSI or

higher. Minimum recommended pipe size is 3/4 in. Larger diameter pipe is always better. Incorrect selection

and installation of any tube, pipe or hose could result in bursting and injury. Connect piping system to tank

using the same size fitting as the discharge port.

Minimum Pipe Size For Compressed Air Line

CFM

LENGTH OF PIPING SYSTEM

25 FEET 50 FEET 100 FEET 250 FEET

10 1/2 inch 1/2 inch 3/4 inch 3/4 inch

20 3/4 inch 3/4 inch 3/4 inch 1 inch

40 3/4 inch 1 inch 1 inch 1 inch

60 3/4 inch 1 inch 1 inch 1 inch

100 1 inch 1 inch 1 inch 1-1/4 inch

Chart 1

Installing A Shut-Off Valve

A shut-off valve should be installed on the discharge port of the

tank to control the air flow out of the tank. The valve should be

located between the tank and the piping system.

Never install a shut-off valve between the compressor pump and the tank. Personal injury and/or

equipment damage may occur. Never use reducers in discharge piping.

When creating a permanently installed system to distribute compressed air, find the total length of the

system and select pipe size from Chart 1. Bury underground lines below the frost line and avoid pockets

where condensation can gather and freeze.

Apply air pressure to the piping installation and make sure all joints are free from leaks BEFORE

underground lines are covered. Before putting the compressor into service, find and repair all leaks in the

piping, fittings and connections.

Figure 5

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

10

INSTALLATION INSTRUCTIONS (CONTINUED)

Wiring

Improperly grounded motors are shock hazards. Make sure all the equipment is properly

grounded.

All wiring and electrical connections must be performed by a qualified electrician

familiar with induction motor controls. Installations must be in accordance with local and

national codes.

Overheating, short circuiting and fire damage will result from inadequate wiring.

Disconnect, tag and lock out power source, then release all pressure from the system before

attempting to install, service, relocate or perform any maintenance.

Damage to the motor from improper electrical voltage or connection will void the warranty.

Wiring must be installed in accordance with National Electrical Code and local codes and standards that

have been set up covering electrical apparatus and wiring. These should be consulted and local ordinances

observed. Be certain that adequate wire sizes are used, and that:

• Service is of adequate ampere rating.

• The supply line has the same electrical

characteristics (voltage, cycles and phase) as

the motor. Refer to motor name plate for

electrical ratings and specifications.

• The line wire is the proper size and that no

other equipment is operated from the same

line. The chart gives minimum recommended

wire sizes for compressor installations.

• Use a slow blow fuse type T or a 240 Volt

double pole circuit breaker.

Minimum Wire Size (Use 75°C Copper Wire)

Make sure voltage is correct with the motor wiring.

NOTE: If using 208 volts single phase, make sure the motor name plate states it is rated for 208 volts single

phase. 230 volt single phase motors do not work on 208 volts unless they have the 208 volt rating.

Single Phase

HP Amps 230V

1-4 HP up to 22.0 10 AWG

5.0 8 AWG

Recommended wire sizes may be larger than the minimum set up by local ordinances. If so, the larger size

wire should be used to prevent excessive line voltage drop. The additional wire cost is very small compared

with the cost of repairing or replacing a motor electrically “starved” by the use of supply wires which are too

small.

WIRING INSTRUCTIONS

1. Inspect the source wiring before continuing with installation. Confirm voltage with volt meter line-to-

ground (see Figure 7).

Figure 6

Volt Meter -

120 Volts

Volt Meter -

230/240 Volts

Line Wire

Ground Wire

Line Wire

Ground Wire

Figure 7 Figure 8

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

11

Volt meter should read 120 Volts.

Confirm voltage with volt meter line-to-line Volt

meter should read 230 / 240 Volts (see Figure 8).

2. Remove the pressure switch cover by loosening

the screw (see Figure 9). Use a Phillips

screwdriver (not included). Pressure switch styles

may vary.

3. Familiarize yourself with the pressure switch

once cover is removed.

4. Remove ground screw. Install strain relief on

pressure switch. DO NOT tighten strain relief on

power cord until wiring is complete. Insert the

bare wires (black, white, bare/green) through

the strain relief.

Attach bare/green ground wire first to ground

screw on pressure switch body.

Look for the “Line” markings on pressure

switch. Install Line wires and tighten terminal

screws.

5. Tighten strain relief nut. Place a flathead

screwdriver (not included) into raised notch and

tap screwdriver with hammer (not included)

until tight.

Tighten strain relief screws to hold power cord

securely. Replace the pressure switch cover

(knob must be in the same position as when

removed to sit correctly in place). Tighten the

pressure switch screw with Phillips screwdriver.

Check that switch is in the OFF position. Follow

break-in procedure starting on page 13.

Figure 10

Tank Pressure

Gauge

ASME Safety

Valve

Line Terminal

Ground

Screw

Motor Cord

Strain Relief

Motor Terminal

Motor Power

Cord

Figure 9

Screw

Figure 11

Terminal Screw

White Line Wire

Black Line Wire

Power Cord

Strain Relief

Bare/Green

Ground

Wire

Figure 12

Strain Relief

Nut

Strain Relief Screw

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

12

INSTALLATION INSTRUCTIONS (CONTINUED)

Grounding

Improperly grounded electrical components are shock hazards. Make sure all the

components are properly grounded to prevent death or serious injury.

This product must be grounded. Grounding reduces the risk of electrical shock by providing an escape wire

for the electric current if short circuit occurs. This product must be installed and operated with a power cord

or cable that has a grounding wire.

Install permanent wiring from the electrical source

to the pressure switch with a ground conductor

connected to the grounding screw on the pressure

switch. A properly sized cord with a ground conductor

and plug may also be installed by the user.

Installing Air Filter

Install air filter on pump (see Figure 13). Filter styles

may vary.

Lubrication

This unit contains no oil.

Before operating compressor, fill to

the center of the sight gauge (see Figure 15).

Using any other type of oil may

shorten pump life and damage

valves.

Recommended Oil (2 Options)

Single viscosity SAE 30 ISO100 nondetergent compressor

oil. Part number ST125303AV (0.5 qt) or ST126701AV (4

qt).

10W30 synthetic oil such as Mobil 1

®

or CE0032 (1 qt).

Oil Capacity

Approximately 47.4 oz.

Remove oil fill plug on pump. Check oil level; some

models are shipped with oil in the pump. Add oil if

needed. Fill the pump with oil to the center of the

sight gauge using oil fill opening (see Figure 15).

Place oil fill plug back on pump.

Do NOT fill the pump

through the breather cap opening as this may cause oil to

leak and spray out during operation.

Do not use regular automotive oil. Additives in

regular motor oil can cause valve deposits and

reduce pump life.

For maximum pump life, drain and replace oil after

the first 50 hours of run time and then follow the

regular maintenance schedule outlined later in the

manual.

This pump has an oil sight glass as shown in Figure

14. Oil level can be monitored and maintained as

shown in Figure 15.

NOTE: Some residual oil may still be in the pump

from factory testing leaving a thin coat on the sight

gauge; however, there is not enough oil to operate

the unit.

Figure 13

Air Filter

Figure 14

Oil FIll

Plug

Sight

Glass

Oil Drain Plug

Figure 15

Full

Low

Sight Glass

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

13

OPERATING INSTRUCTIONS

Start-up / Break-in Procedure

Do not attach air tools to open end of the hose until start-up is completed and the unit checks

okay.

Never disconnect threaded joints with pressure in tank!

1. Return power to unit from main.

2. Check oil level per the Lubrication Section of this manual.

3. Open the tank drain valve (see Figure 16). Turn outlet valve to open air flow.

4. Move pressure switch to the AUTO position to run the unit (see Figure 17).

5. Run the unit for thirty (30) minutes at zero (0) PSI (under no load) to break in pump parts.

6. Move the pressure switch lever or knob to OFF and turn tank drain valve to shut off air flow. The

compressor is now ready for use.

7. Change oil after first fifty (50) hours of operation. Perform oil changes every three (3) months or two

hundred (200) hours of run time, whichever comes first.

On/Off Cycling of Compressor

Drain tank every day to prevent corrosion and possible injury due to tank damage. For optimal

performance of tank drain, tank pressure should be between 10 PSI - 40 PSI. Do not operate

drain with more than 40 PSI in tank or drain valve may be damaged. Drain tank of moisture daily using the drain valve

in the bottom of the tank.

Drain liquid from tank daily.

In the AUTO position, the compressor pumps air into the tank. When a shut-off (preset “cut-out”) pressure

is reached, the compressor automatically shuts off.

If the compressor is left in the AUTO position and air is depleted from the tank by use of a tire chuck, tool,

etc., the compressor will restart automatically at its preset “cut-in” pressure. When a tool is being used

continuously, the compressor will cycle on and off automatically.

In the OFF position, the compressor will not operate.

MOISTURE IN COMPRESSED AIR

Moisture in compressed air will form into droplets as it comes from an air compressor pump. When

humidity is high or when a compressor is in continuous use for an extended period of time, this

moisture will collect in the tank. When using a paint spray or sandblast gun, this water will be carried

from the tank through the hose, and out of the gun as droplets mixed with the spray material.

IMPORTANT: This condensation will cause water spots in a paint job, especially when spraying other

than water based paints. If sandblasting, it will cause the sand to cake and clog the gun, rendering

it ineffective. A filter in the air line, located as near to the gun as possible, will help eliminate this

moisture.

Figure 16 Figure 17

Tank Drain

Valve

TROUBLESHOOTING GUIDE

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

14

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Low discharge pressure 1. Air demand exceeds pump capacity 1. Reduce air demand or use a compressor with more

capacity.

2. Air leaks (fittings, tubing on

compressor, or plumbing outside of

system).

2. Listen for escaping air. Apply soap solution to

all fittings and connections. Bubbles will appear

at points of leakage. Tighten or replace leaking

fittings or connections. Use pipe thread sealant.

3. Restricted air intake 3. Clean or replace the air filter element.

4. Blown gaskets 4. Replace any gaskets proven faulty on inspection.

5. Leaking or damaged valves 5. Remove head and inspect for valve breakage,

misaligned valves, damaged valve seats, etc. Replace

defective parts and reassemble.

Install a new head gasket

each time the head is removed.

Excessive noise (knocking)

1. Loose motor pulley or flywheel. 1. Tighten pulley / flywheel clamp bolts and set-

screws.

2. Loose fasteners on pump or motor. 2. Tighten fasteners.

3. Lack of oil in crankcase 3. Check for proper oil level; if low, check for possible

damage to bearings. Dirty oil can cause excessive

wear.

4. Worn connecting rod 4. Replace connecting rod. Maintain oil level and

change oil more frequently.

5. Worn piston pin bores 5. Remove piston assemblies from the compressor and

inspect for excess wear. Replace excessively worn

piston pin or pistons, as required. Maintain oil level

and change oil more frequently.

6. Piston hitting the valve plate 6. Remove the compressor head and valve plate

and inspect for carbon deposits or other foreign

matter on top of piston. Replace head and valve

plate using new gasket. See Lubrication section for

recommended oil.

7. Noisy check valve in compressor

system

7. Replace check valve.

Do not disassemble check valve

with air pressure in tank.

Large quantity of oil in the

discharge air

NOTE: In an oil lubricated

compressor there will always

be a small amount of oil in the

air stream.

1. Worn piston rings 1. Replace with new rings. Maintain oil level and

change oil more frequently.

2. Compressor air intake restricted

2. Clean or replace filter. Check for other restrictions

in the intake system.

3. Excessive oil in compressor

3. Drain down to full level.

4. Wrong oil viscosity

4. Use Mobil 1

®

10W-30 or full synthetic.

Water in discharge air/tank Normal operation. The amount of water

increases with humid weather

1. Drain tank more often. At least daily.

2. Add a filter to reduce the amount of water in the

air line.

TROUBLESHOOTING GUIDE

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

15

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Motor hums and runs slowly or

not at all.

1. Low voltage. 1. Check incoming voltage. It should be approximately

230 volts. Motor will not run properly on 208 volts.

Low voltage could be due to wires (from electrical

source to compressor) being too small in diameter

and / or too long. Have a qualified electrician check

these conditions and make repairs as needed.

2. Too many devices on same circuit. 2. Limit the circuit to the use of compressor only.

3. Loose electrical connections. 3. Check all electrical connections.

4. Malfunctioning pressure switch -

contacts will not close.

4. Replace pressure switch.

5. Malfunctioning check valve. 5. Replace check valve.

Do not disassemble check valve

with air pressure in tank.

6. Defective unloader valve on pressure

switch.

6. Replace unloader valve.

7. Defective motor capacitor(s). 7. Replace capacitor(s).

8. Defective motor. 8. Replace motor.

Reset mechanism cuts out

repeatedly or circuit breaker

trips repeatedly.

1. Lack of proper

ventilation / room temperature too

high.

1. Move compressor to well-ventilated area.

2. Too many devices on same circuit. 2. Limit the circuit to the use of only the air

compressor.

3. Restricted air intake. 3. Clean or replace filter element.

4. Loose electrical connection. 4. Check all electrical connections.

5. Pressure switch shut-off pressure set

too high.

5. Replace pressure switch.

6. Malfunctioning check valve. 6. Replace check valve.

Do not disassemble check valve

with air pressure in tank.

7. Defective unloader valve on pressure

switch.

7. Replace unloader valve.

8. Defective motor capacitor(s). 8. Replace capacitor(s).

9. Malfunctioning motor. 9. Replace motor.

Tank does not hold pressure

when compressor is off and

the shut off valve is closed.

1. Air leaks (fittings, tubing on

compressor, or plumbing outside

system).

1. Check all connections with soap and water solution.

Tighten; or remove and apply sealant to threads,

then reassemble.

2. Worn check valve. 2. Replace check valve.

Do not disassemble check valve

with air pressure in tank.

3. Check tank for cracks or pin holes. 3. Replace tank. Never repair a damaged tank.

Pressure switch continuously

blows air out the unloader

valve

Malfunctioning check valve Replace the check valve if the unloader valve on the

pressure switch bleeds off constantly when unit shuts

off.

Do not disassemble check valve

with air pressure in tank.

Pressure switch does not

release air when the unit shuts

off

Malfunctioning unloader valve on

pressure switch

Replace the pressure switch if it does not release the

pressure for a short period of time when the unit shuts

off.

Do not disassemble pressure

switch with air pressure in tank

Excessive vibration

1. Loose fasteners on pump or motor 1. Tighten fasteners.

2. Belt needs replaced 2. Replace with correct size.

3. Belt alignment 3. Align flywheel and pulley.

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

16

MAINTENANCE AND INSPECTION INSTRUCTIONS

Disconnect, tag and lock out power source then release all pressure from the system before

attempting to install, service, relocate or perform any maintenance.

All repairs should be performed by an authorized service representative.

In order to maintain efficient operation of the compressor system,

check the air filter and oil level before each use. The ASME safety

valve should also be checked daily (see Figure 18). Pull ring on

safety valve and allow the ring to snap back to normal position.

This valve automatically releases air if the tank pressure exceeds

the preset maximum. If air leaks after the ring has been released,

or the valve is stuck and cannot be actuated by the ring, the ASME

safety valve must be replaced.

Do not tamper with the ASME safety valve.

Tank

Never attempt to repair or modify a tank! Welding, drilling or any other modification will

weaken the tank resulting in damage from rupture or explosion. Always replace worn, cracked

or damaged tanks.

Drain liquid from tank daily.

Drain Tank: Disconnect, tag and lock out power source; release pressure. Drain moisture from tank by

opening drain valve underneath tank once tank pressure is less than 40 PSI (See Figure 16 on page 13).

The tank should be carefully inspected at a minimum of once a year. Look for cracks forming near the

welds. If a crack is detected, remove pressure from tank immediately and replace.

Compressor Lubrication

See Installation. Add oil as required. The oil should be changed every three months or after every 200 hours

of operation; whichever comes first.

If the compressor is run under humid conditions for short periods of time, the humidity will condense in

the crankcase and cause the oil to look creamy. Oil contaminated by condensed water will not provide

adequate lubrication and must be changed immediately. Using contaminated oil will damage bearings,

pistons, cylinders and rings and is not covered under warranty. To avoid water condensation in the oil,

periodically run the compressor with tank pressure near 120 PSI for 2-stage compressors by opening the

drain cock or an air valve connected to the tank or hose. Run the pump for an hour at a time at least once a

week or more often if the condensation reoccurs.

IMPORTANT: Change oil after first 50 hours of operation.

Air Filter

Never run the compressor pump without an intake air filter or

with a clogged intake air filter. The air filter element should be

checked monthly (see Figure 19). Operating compressor with

a dirty filter can cause high oil consumption and increase oil

contamination in the discharge air. If the air filter is dirty it must

be replaced.

Figure 18 - ASME Safety Valve

Figure 19

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

17

Belts

Lock out and tag the power then release all pressure from the tank to prevent unexpected

movement of the unit.

Check belt tension every 3 months. Adjust belt tension to allow 3/8 inch to 1/2 inch deflection with normal

thumb pressure. Also, align belts using a straight edge against the face of the flywheel and touching the

rim on both sides of the face. The belts should be parallel to this straight edge (see Figure 20). Dimension A

should be the same as B and C to ensure proper alignment of the belts.

Slots in the bed-plate allow for sliding the motor back and forth to adjust belt tension.

Removing Belt Guard

When removing belt guard front to

inspect or replace belts, inspect plastic retaining

clips and replace if damaged or if clip can be removed without a tool.

Removing Retaining Clips

1. Using crescent wrench on pliers, rotate clip 90°.

2. Pull clip out and away from beltguard.

3. Reverse process to reinstall after inspecting the clip.

Storage

If compressor is to be stored for a short period of time, make sure that it is stored in a normal position and

in a cool protected area.

MAINTENANCE SCHEDULE

OPERATION DAILY WEEKLY MONTHLY 3 MONTHS

Check Oil Level

l

Drain Tank

l

Check Air Filter

l

Check Safety Valve

l

Clean Unit

l

Check Belt Tightness

l

Change Oil*

l

* Change oil after first fifty (50) hours of operation then perform oil changes every three (3) months or two hundred

(200) hours of run time, whichever comes first.

A B

C

Figure 20 - Top View

Air Compressor

Motor

Flywheel

Straight Edge

Motor

Drive

Pulley

Setscrew

Figure 21

1

2

For Repair Parts, visit www.campbellhausfeld.com

24 hours a day – 365 days a year

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as shown in parts list

REPAIR PARTS ILLUSTRATION FOR CE5002 AND XC602100

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

18

1

2

3

4

La page charge ...

Campbell Hausfeld CE5002 Mode d'emploi

Ce manuel convient également à

Campbell Hausfeld CE5002 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents