Hitachi G 14DSL Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: G 14DSL

Catégorie: Outils électroportatifs

Taper: Safety Instructions And Instruction Manual

Ce manuel convient également à

G 18DSL

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires

avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un

endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool.

This manual should be stored in safe place.

Model Cordless Disc Grinder

Modèle Meuleuse sans fil

Modelo Amoladora angular a bateríe

G 14DSL

•

G 18DSL

G14DSL

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

00Cover_G14DSL_US 9/4/13, 15:121

CONTENTS

Page

IMPORTANT SAFETY INSTRUCTIONS ............... 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 3

GENERAL POWER TOOL SAFETY WARNINGS.. 3

SAFETY WARNINGS FOR GRINDING OPERATIONS ..

KICKBACK AND RELATED WARNINGS .............. 6

SAFETY WARNINGS SPECIFIC FOR

GRINDING OPERATIONS .............................. 6

GENERAL SAFETY INSTRUCTIONS FOR GRINDERS .......

SPECIFIC SAFETY RULES AND SYMBOLS ......... 7

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER ...................................... 8

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE BATTERY AND BATTERY CHARGER .......

CAUTION ON LITHIUM-ION BATTERY ............... 9

Page

FUNCTIONAL DESCRIPTION .................................. 11

NAME OF PARTS ................................................ 11

SPECIFICATIONS ................................................ 12

ASSEMBLY AND OPERATION ............................... 13

APPLICATIONS ................................................... 13

REMOVAL AND INSTALLATION METHOD OF

BATTERY ...................................................... 13

CHARGING METHOD ......................................... 13

PRIOR TO OPERATION ....................................... 15

GRINDER OPERATION ....................................... 16

DEPRESSED CENTER WHEEL

ASSEMBLY AND DISASSEMBLY ............... 17

MAINTENANCE AND INSPECTION ....................... 18

ACCESSORIES ......................................................... 20

STANDARD ACCESSORIES ............................... 20

PARTS LIST .............................................................. 59

English

ÍNDICE

Español

Página

INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD ...

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN ...

SEGURIDAD ............................................................. 40

ADVERTENCIAS DE SEGURIDAD GENERAL DE

LA HERRAMIENTA ELÉCTRICA .................. 40

ADVERTENCIAS DE SEGURIDAD PARA MOLER ......

REBOTE Y ADVERTENCIAS RELACIONADAS

...... 43

ADVERTENCIAS DE SEGURIDAD PARA MOLER

..... 43

INSTRUCCIONES GENERALES DE SEGURIDAD

PARA AMOLADORAS ................................. 44

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ................................................. 44

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA EL CARGADOR DE

BATERÍAS ..................................................... 46

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA LA BATERÍA Y EL

CARGADOR DE BATERÍAS ......................... 46

Página

ADVERTENCIA DE LA BATERÍA DE LITIO ......... 47

DESCRIPCIÓN FUNCIONAL .................................... 49

NOMENCLATURA ............................................... 49

ESPECIFICACIONES ............................................ 50

MONTAJE Y OPERACIÓN ...................................... 51

APLICACIONES ................................................... 51

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 51

MÉTODO DE CARGA .......................................... 51

ANTES DE LA OPERACIÓN ................................ 53

OPERACIÓN DE LA AMOLADORA

ANGULAR .................................................... 54

MONTAJE Y DESMONTAJE DE LA

RUEDA DE DISCO ABOMBADO ................. 55

MANTENIMIENTO E INSPECCIÓN ........................ 56

ACCESORIOS ........................................................... 58

ACCESORIOS ESTÁNDAR ................................. 58

LISTA DE PIEZAS .................................................... 59

Page

CONSIGNES DE SÉCURITÉ IMPORTANTES..... 21

SIGNIFICATION DES MOTS D’AVERTISSEMENT .....

SECURITE ................................................................ 21

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES...

AVERTISSEMENTS DE SÉCURITÉ POUR LES

OPÉRATIONS DE MEULAGE ...................... 23

RECUL DE L'APPAREIL ET AVERTISSEMENTS

ASSOCIÉS .................................................... 24

AVERTISSEMENTS DE SÉCURITÉ SPÉCIFIQUES

AUX OPÉRATIONS DE MEULAGE ............... 24

CONSIGNES DE SECURITE GENERALES

RELATIVES AUX MEULEUSES DROITES ....

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES ....

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE .......... 27

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DE LA BATTERIE ET

DU CHARGEUR DE BATTERIE .................... 27

Français

Page

PRÉCAUTIONS RELATIVES A LA BATTERIE AU

LITHIUM ION ................................................ 28

DESCRIPTION FONCTIONNELLE ........................... 30

NOM DES PARTIES ............................................ 30

SPECIFICATIONS ................................................ 31

ASSEMBLAGE ET FONCTIONNEMENT ................ 32

UTILISATIONS .................................................... 32

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 32

MÉTHODE DE RECHARGE ................................. 32

AVANT L’UTILISATION ...................................... 34

UTILISATION DE LA MEULEUSE ...................... 35

ASSEMBLAGE ET DESASSEMBLAGE DE LA

MEULE A DEPRESSION CENTRALE .......... 36

ENTRETIEN ET INSPECTION .................................. 37

ACCESSOIRES ......................................................... 39

ACCESSOIRES STANDARD ............................... 39

LISTE DES PIECES ................................................... 59

TABLE DES MATIERES

00Cover_G14DSL_US 9/4/13, 15:122

English

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust of fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the influence of drugs, alcohol or

medication.

01Eng_G14DSL_US 8/28/13, 16:273

English

A moment of inattention while operating

power tools may result in serious personal

injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different

from those intended could result in a

hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by

the manufacturer.

A charger that is suitable for one type of

battery pack may create a risk of fire when

used with another battery pack.

b) Use power tools only with specifically

designated battery packs.

Use of any other battery packs may create a

risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts.

This will ensure that the safety of the power

tool is maintained.

01Eng_G14DSL_US 8/28/13, 16:274

English

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known [to the State of California]

to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

●

Lead from lead-based paints,

●

Crystalline silica from bricks and cement and other

masonry products, and

●

Arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to filter out microscopic particles.

SAFETY WARNINGS FOR GRINDING

OPERATIONS

a) This power tool is intended to function as a

grinder. Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

b) Operations such as sanding, wire brushing or

polishing or cutting-off are not recommended to

be performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

c) Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

d) The rated speed of the accessory must be at least

equal to the maximum speed marked on the

power tool.

Accessories running faster than their rated speed

can break and fly apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

f) The arbour size of wheels, flanges, backing pads

or any other accessory must properly fit the

spindle of the power tool.

Accessories with arbour holes that do not match

the mounting hardware of the power tool will run

out of balance, vibrate excessively and may cause

loss of control.

g) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks. If power tool or accessory is

dropped, inspect for damage or install an

undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute.

Damaged accessories will normally break apart

during this test time.

h) Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments.

The eye protection must be capable of stopping

flying debris generated by various operations. The

dust mask or respirator must be capable of

filtrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.

Fragments of workpiece or of a broken accessory

may fly away and cause injury beyond immediate

area of operation.

j) Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or

its own cord.

Cutting accessory contacting a”live” wire may

make exposed metal parts of the power tool “live”

and shock the operator.

k) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the

spinning accessory.

l) Never lay the power tool down until the accessory

has come to a complete stop.

The spinning accessory may grab the surface and

pull the power tool out of your control.

m) Do not run the power tool while carrying it at your

side.

Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the

housing and excessive accumulation of powdered

metal may cause electrical hazards.

o) Do not operate the power tool near flammable

materials.

Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

01Eng_G14DSL_US 8/28/13, 16:275

English

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the

operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels

may also break under these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can

be avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided,

for maximum control over kickback or torque

reaction during start-up.

The operator can control torque reactions or

kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs.

Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory.

Corners, sharp edges or bouncing have a tendency

to snag the rotating accessory and cause loss of

control or kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade.

Such blades create frequent kickback and loss of

control.

SAFETY WARNINGS SPECIFIC FOR

GRINDING OPERATIONS

a) Use only wheel types that are recommended for

your power tool and the specific guard designed

for the selected wheel.

Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

b) The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator.

The guard helps to protect operator from broken

wheel fragments and accidental contact with

wheel.

c) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may

cause them to shatter.

d) Always use undamaged wheel flanges that are of

correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus

reducing the possibility of wheel breakage. Flanges

for cut-off wheels may be different from grinding

wheel flanges.

e) Do not use worn down wheels from larger power

tools.

Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and may

burst.

GENERAL SAFETY INSTRUCTIONS FOR

GRINDERS

– Check that speed marked on the wheel is equal to

or greater than the rated speed of the grinder;

– Ensure that the wheel dimensions are compatible

with the grinder;

– Abrasive wheels shall be stored and handled with

care in accordance with manufacturer’s

instructions;

– Inspect the grinding wheel before use, do not use

chipped, cracked or otherwise defective products;

– Ensure that mounted wheels and points are fitted

in accordance with the manufacturer’s instructions;

– Ensure that blotters are used when they are

provided with the bonded abrasive product and

when they are required;

– Ensure that the abrasive product is correctly

mounted and tightened before use and run the tool

at no-load for 30 s in a safe position, stop

immediately if there is considerable vibration or if

other defects are detected. If this condition occurs,

check the machine to determine the cause;

– If a guard is equipped with the tool never use the

tool without such a guard;

– Do not use separate reducing bushings or adapters

to adapt large hole abrasive wheels;

– For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length;

– Check that the work piece is properly supported;

– Do not use cutting off wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite

flammable substances;

– Ensure that ventilation openings are kept clear

when working in dusty conditions, if it should

become necessary to clear dust, first disconnect

the tool from the mains supply (use non metallic

objects) and avoid damaging internal parts;

01Eng_G14DSL_US 8/28/13, 16:276

English

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn;

– Pay attention to the wheel that continues to rotate

after the tool is switched off.

SPECIFIC SAFETY RULES AND SYMBOLS

1. ALWAYS use proper guard with grinding wheel.

A guard protects operator from broken wheel

fragments.

2. Accessories must be rated for at least the speed

recommended on the tool warning label.

Wheels and other accessories running over rated

speed can fly apart and cause injury.

3. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

4. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

5. Use only a depressed center wheel with a rated

capacity which is GREATER than 13,300 RPM.

Using any wheel a rated capacity LESS than 13,300

RPM and/or an incorrect sized wheel (see

SPECIFICATIONS at page 12) may result in wheel

breakage, flying wheel fragments, and resulting

in death or serious injury.

6. NEVER touch moving parts.

NEVER place your hands, fingers or

other body parts near the tool’s moving

parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or

safety features in place and in proper working

order. If maintenance or servicing requires the

removal of a guard or safety feature, be sure to

replace the guard or safety feature before resuming

operation of the tool.

8. Use right tool.

Don’t force small tool or attachment to do the job

of a heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

9. NEVER use a power tool for applications other

than those specified.

NEVER use a power tool for applications other than

those specified in the Instruction Manual.

10. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

12. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

13. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to youself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure

and tight.

14. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so

that air can freely flow at all times. Check for dust

build-up frequently.

15. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange

for repairs by a Hitachi authorized service center.

16. NEVER leave tool running unattended. Turn power

off.

Don’t leave tool until it comes to a complete stop.

17. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

18. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry thoroughly.

19. NEVER use a depressed center wheel which is

cracked or deformed or worn away (see the

MAINTENANCE AND INSPECTION section on page

18).

20. NEVER use the grinder in places where the sparks

generated by the grinder can cause explosion, such

as where flammable materials or gases are

present.

21. NEVER push in the push button while the spindle

is running.

22. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

01Eng_G14DSL_US 8/28/13, 16:277

English

23. ALWAYS wear a mank or respirator to protect

yourself from dust or potentially harmful particles

generated during the grinding operation.

24. ALWAYS firmly grip the body handle and side

handle while operating the grinder.

25. ALWAYS have a trial run before grinding

commence. (see Test the grinder before using on

page 15).

26. ALWAYS follow the instructions contained in this

manual when replacing the depressed center

wheel.

27. ALWAYS be careful with buried objict such as an

underground wiring.

Touching these active wiring or electric cable with

this tool, you may receive an electric shock.

Comfirm if there are any buried object such as

electric cable within the wall, floor or ceiling where

you are going to operate here after.

28. Definitions for symbols used on this tool

V ............... volts

—

---

.............. direct current

Hz ............. hertz

A ............... amperes

no ............ no load speed

---/min ...... revolutions or reciprocation per minute

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER

WARNING:

Death or serious bodily injury could result from

improper or unsafe use of battery chargers. To avoid

these risks, follow these basic safety instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and

operating instructions for battery charger Model

UC18YRSL/UC18YFSL.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger,

(2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI

rechargeable battery type BSL1430 and BSL1830.

Other type of batteries may burst causing personal

injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold

by the battery charger manufacturer may result in

a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

7. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected

to damage or stress.

8. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in

good electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as specified in

Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a battery charger is given in

watts rather than in amperes, the corresponding

ampere rating is to be determined by dividing the

wattage rating by the voltage rating–for example:

1,250 watts

125 volts

= 10 amperes

9. Do not operate battery charger with damaged cord

or plug-replace them immediately.

10. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged

in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a

qualified serviceman when service or repair is

required. Incorrect reassembly may result in a risk

of electric shock or fire.

12. To reduce risk of electric shock, unplug charger

from receptacle before attempting any

maintenance or cleaning. Removing the battery

will not reduce this risk.

01Eng_G14DSL_US 8/28/13, 16:278

English

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE BATTERY AND BATTERY

CHARGER

You must charge the battery before you can use the

power tool. Before using the model

UC18YRSL/UC18YFSL battery charger, be sure to read

all instructions and cautionary statements on it, the

battery and in this manual.

CAUTION:

USE ONLY HITACHI BATTERY TYPE BSL1430 AND

BSL1830. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery or

battery charger can lead to serious

injury. To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is

damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery

charger’s air vents. Electric shock or

damage to the battery charger may

result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where

there is low humidity and good

ventilation.

6. NEVER charge when the temperature is below

32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for

the battery or the battery charger.

9. NEVER use a booster transformer when

charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in

places where the temperature may reach

or exceed 104°F (40°C).

12.

ALWAYS

operate charger on standard household

electrical power (120 volts). Using the

charger on any other voltage may

overheat and damage the charger.

13.

ALWAYS

wait at least 15 minutes between

charges to avoid overheating the

charger.

14.

ALWAYS

disconnect the power cord from its

receptacle when the charger is not in

use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor

may stop. This is not the trouble but the result of

protection function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In

this case, release the switch of tool and eliminate

causes of overloading. After that, you can use it

again.

3. If the battery is overheated under overload work,

the battery power may stop.

In this case, stop using the battery and let the

battery cool. After that, you can use it again (only

BSL1830).

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on

the battery.

䡬

During work make sure that swarf and dust do not

fall on the battery.

䡬

Make sure that any swarf and dust falling on the

power tool during work do not collect on the

battery.

䡬

Do not store an unused battery in a location

exposed to swarf and dust.

䡬

Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it

together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or

subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

7. If the battery charging fails to complete even when

a specified recharging time has elapsed,

immediately stop further recharging.

8. Do not put or subject the battery to high

temperatures or high pressure such as into a

microwave oven, dryer, or high pressure container.

9. Keep away from fire immediately when leakage

or foul odor are detected.

10. Do not use in a location where strong static

electricity generates.

01Eng_G14DSL_US 8/28/13, 16:279

English

11. If there is battery leakage, foul odor, heat

generated, discolored or deformed, or in any way

appears abnormal during use, recharging or

storage, immediately remove it from the

equipment or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your

eyes, do not rub your eyes and wash them well

with fresh clean water such as tap water and

contact a doctor immediately.

If left untreated, the liquid may cause eye-

problems.

2. If liquid leaks onto your skin or clothes, wash well

with clean water such as tap water immediately.

There is a possibility that this can cause skin

irritation.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

3. If you find rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the first time, do not use and return

it to your supplier or vendor.

WARNING:

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of fire. Please observe the

following matters when storing the battery.

䡬

Do not place electrically conductive cuttings, nails,

steel wire, copper wire or other wire in the storage

case.

䡬

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 1).

01Eng_G14DSL_US 8/28/13, 16:2710

English

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ from those on your

own power tool.

NAME OF PARTS

1. Cordless Disc Grinder (G14DSL / G18DSL)

䡬

Battery

Gear cover

Packing gland

Switch

Housing

Side handle

Brush cap

Wheel guard

Depressed

center wheel

Push button

Nameplate

Battery

Fig.1

Battery

Latch

Ventilation holes

Terminals

Battery cover

Battery

Latch

Ventilation holes

Terminals

Battery cover

01Eng_G14DSL_US 8/28/13, 16:2711

English

2. Battery Charger

Fig. 2

NOTE: The charging time may vary according to ambient temperature and power source voltage.

2. Battery Charger

Pilot lamp

Cord

Nameplate

Guide rail

Model UC18YRSL UC18YFSL

Input power source Single phase: AC 120 V 60 Hz

Charging time Approx. 45 min.

Charger

Charging voltage DC 14.4 V 18 V

Charging current DC 3.5 A

Weight 1.3 lbs. (0.6 kg) 1.1 lbs. (0.5 kg)

SPECIFICATIONS

1. Cordless Dise Grinder

Model G14DSL G18DSL

Motor DC motor

No-Load Speed 9,300/min 9,100/min

Wheel Size:

external diam. 4-1/2" (115 mm)

hole diam. 7/8" (22 mm)

Model BSL 1430 BSL 1830

Type Lithium – ion battery

Battery

Voltage DC 14.4V DC 18V

Capacity 3.0 Ah

Weight 3.7 lbs (1.7 kg) 4.0 lbs (1.8 kg)

Pilot lamp

Cord

Nameplate

Guide rail

01Eng_G14DSL_US 8/28/13, 16:2712

English

APPLICATIONS

䡬

Removal of casting fin and finishing of various type

of steel, bronze and aluminum materials and

castings.

䡬

Grinding of welded sections or sections cut by

means of an acetylene torch.

䡬

Grinding of synthetic resins, slate, brick, marble.

WARNING:

To avoid the risk of serious injury, NEVER use this

grinder with cup wheels and/or saw blades.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

1. Battery removal

Hold the handle tightly and push the battery latch

to remove the battery (see Fig. 3).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 3).

Fig. 3

CHARGING METHOD

NOTE:

Before plugging into the receptacle, make sure the

following points.

䡬

The power source voltage is stated on the

nameplate.

䡬

The cord is not damaged.

ASSEMBLY AND OPERATION

Latch

Battery

Pull out

Insert

Push

WARNING:

Do not charge at voltage higher than indicated on

the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals)

WARNING:

Do not use the electrical cord if

damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown

in Fig. 4, 5.

Fig. 4

Fig. 5

Battery

Charger

Pilot lamp

Battery

Charger

Pilot lamp

01Eng_G14DSL_US 8/28/13, 16:2713

English

3. Charging

When the battery is connected to the battery

charger, charging will commence and the pilot

lamp will light in red. (See Table 2)

NOTE:

If the pilot lamp flikers in red, pull out the plug

from the receptacle and check if the battery is

properly mounted.

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before

being recharged.

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time (At 20°C)

NOTE:

The charging time may vary according to

temperature and power source voltage.

4. Disconnect battery charger from the receptacle.

Table 3 Recharging ranges of batteries

Rechargeable Temperatures at which the

batteries battery can be recharged

BSL1430, 32°F–104°F

BSL1830 (0°C–40°C)

Charger

UC18YRSL / UC18YFSL

Battery

BSL1430, BSL1830 Approx. 45 min.

CAUTION

●

Do not pull the plug out of the receptacle by pulling

on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out

the battery from the battery charger.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its

battery. If you continue to use the tool and exhaust

the electric current, the battery may be damaged

and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately

after use. If such a battery is recharged immediately

after use, its internal chemical substance will

deteriorate, and the battery life will be shortened.

Leave the battery and recharge it after it has cooled

for a while.

When the battery is fully charged, the pilot lamp

will blink in red slowly. (At 1-second intervals) (See

Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown

in Table 2, according to the condition of the charger

or the rechargeable battery.

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1

seconds. (off for 0.1 seconds)

Lights continuously

Lights for 1 secods. Does not light for 0.5

seconds. (off for 0.5 seconds)

Before

charging

While

charging

Charging

complete

Charging

impossible

Blinks

(red)

Lights

(red)

Blinks

(red)

Flickers

(red)

Lights

(green)

Blinks

(red)

Malfunction in the

battery or the charger

Battery overheated.

Unable to charge

(Charging will

commence when

battery cools).

Overheat

standby

The

pilot

lamp

lights or

blinks.

01Eng_G14DSL_US 8/28/13, 16:2714

English

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes rest

until the next charging.

●

If the battery is rechraged when it is warm due to

battery use or exposure to sunlight, the pilot lamp

may light in green.

The battery will not be recharged. In such a case,

let the battery cool before charging.

●

When the pilot lamp flikers rapidly in red (at 0.2–

second intervals), check for and take out any

foreign objects in the charger’s battery installation

hole. If there are no foreign objects, it is probable

that the battery or charger is malfunctioning. Take

it to your authorized Service Center.

PRIOR TO OPERATION

1. Power switch

Ensure that the switch is in the OFF position.

2. Check your work environment

Ensure the following before operation:

䡬

No flammable gas, liquid, or object at

worksite.

䡬

When grinding thin steel sheet it may cause

a high booming noise.

To avoid such noise, place a rubber mat under

the workpiece.

䡬

Clear the area of children or unauthorized

personnel.

3. Mounting the wheel guard

Be sure to mount the wheel guard at an angle that

will protect the operator’s body from injury by a

broken wheel piece.

[Installing Wheel Guard]

䡬

Slightly loosen the screw on the wheel guard.

䡬

Install the wheel guard to the packing gland,

turn it to the angle suitable for operation, and

make adjustment.

䡬

After the adjustment, ensure that the screw

is securely tightened on the wheel guard in

order to fix it completely.

WARNING:

If the wheel guard is not attached properly, a

broken wheel may result in and cause death or

serious injury.

4. Thoroughly check that the depressed center wheel

is free of cracks, splits and other abnomalities

before mounting. Make sure it is firmly clamped

and has been properly mounted. Refer to page 17

of this manual for Depressed Center Wheel

Assembly and Disassembly

5. Test the grinder before using.

Before actually beginning the grinding work, test

the grinder by first clearing the area of all other

personnel. Make sure the wheel guard is in place

and that you are wearing eye protection. Turn the

grinder “on”, and make sure the grinder runs

smoothly and shows no abnormalities.

Duration of the trial run is as follows:

When depressed center wheel

is replaced ............................... 3 minutes or

When starting daily work ...... 1 minute or

6. Use only properly rated depressed center wheels.

Use only depressed center wheels rated at 13,300

RPM or more.

Using a depressed center wheel rated less can lead

to wheel disintegration during operation and cause

serious bodily injury.

7. Check the push button.

Make sure that the push button is disengaged by

pushing push button two or three times before

turning on the grinder. (Fig. 8)

8. About Remaining Battery Indicator

When pressing the remaining battery indicator

switch, the remaining battery indicator lamp lights

and the battery remaining power can be checked.

Fig. 5

Wheel guard

Packing gland

01Eng_G14DSL_US 8/28/13, 16:2715

English

(Fig.6) When releasing your finger from the

remaining battery indicator switch, the remaining

battery indicator lamp goes off. The table 5 shows

the state of remaining battery indicator lamp and

the battery remaining power.

As the remaining battery indicator shows

somewhat differently depending on ambient

temperature and battery characteristics, read it as

a reference.

Fig. 6

NOTE:

䡬

Do not give a strong shock to the switch panel or

break it.It may lead to a trouble.

䡬

To save the battery power consumption, the

remaining battery indicator lamp lights while

pressing the remaining battery indicator switch.

GRINDER OPERATION

CAUTION:

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the causes

of overloading.

NOTE:

䡬

To prevent injuries, this product has a function that

prevents unexpected motor rotation when the

battery is inserted. The motor will not run if the

battery is inserter while the switch is still ON. After

installing the battery, turn the switch off and then

back on again.

䡬

The G14DSL and G18DSL models are equipped

with a protection function that will shut down the

tool in the event of an overload.

Should the tool shut down due to an overload, turn

the power off and then turn it back on again.

An overload that stops tool operation and lasts

more than 10 seconds may not be released by

turning the power off and on. Should this happen,

remove the battery from the tool and reinstall it

before turning on the power switch.

1. Hold the grinder firmly by its housing and side

handle (Fig. 1).

The grinder produces a counterforce which must

be controlled by firmly holding onto the grinder.

2. Turn the grinder “on”. (Fig. 7)

While holding the grinder firmly, use one finger to

slide the switch to the “on” position.

3. Use light grinding pressure.

There is no need to press hard when grinding.

Usually the grinder’s own weight is sufficient to

allow the required light contact with the surface to

be ground.

WARNING:

Do not press the grinder forcibly against the

surface to be ground. Heavy pressure can result

in wheel breakage and serious injury. It can also

damage the surface being ground or damage the

grinder’s motor.

State of lamp Battery Remaining Power

The battery remaining power

is enough.

The battery remaining power

is a half.

The battery remaining power

is nearly empty.

Re-charge the battery soonest

possible.

Table 5

Remaining battery

indicator lamp

Remaining battery

indicator switch

Fig. 7

Switch

ON OFF

01Eng_G14DSL_US 8/28/13, 16:2716

English

4. Use proper grinding angle.

Grind only with the wheel’s edge by lifting the

grinder 15° to 30°, as shown in Fig. 8.

CAUTION:

Do not use the entire surface of the depressed

center wheel. Use only the edge of the depressed

center wheel.

5. Move the grinder in the proper direction.

When using a new depressed center wheel in

direction A (Fig. 8), the wheel edge may cut into the

workpiece. In this case, grind in direction B (Fig. 8).

Once the wheel edge is worn, the workpiece can

be ground in both directions.

Fig. 8

NOTE:

The wheel provided (resinoid wheel) is rated as

Class A grain and # 36 grain size. It is most suitable

for heavy grinding of steel and other types of

materials.

6. Adjust operation to desired finish.

For a fine finish, decrease pressure by lifting

slightly. Grind slowly and at the appropriate speed.

CAUTION:

The revolving depressed center wheel will create

air turbulence.

Do no lay the grinder down in areas of dust or dirt

until it has come to a complete stop.

DEPRESSED CENTER WHEEL ASSEMBLY

AND DISASSEMBLY

WARNING:

Be sure to turned off the switch and pull out the

battery.

1. Assembly

(1) Turn the disc grinder upsidedown so that the

spindle is facing upward.

(2) Align the oval-shaped indentation of the wheel

washer with the notched part of the spindle, then

attach them.

(3) Fit the protuberance of the depressed center wheel

onto the wheel washer.

(4) Screw the wheel nut onto the spindle.

(5) While pushing the push button with one hand, lock

the spindle by turning the depressed center wheel

slowly with the other hand.

Tighten the wheel nut by using the supplied

wrench as shown in Fig. 9.

CAUTION:

Tighten the wheel nut securely and confirm that

the depressed center wheel does not wobble.

2. Disassembly

To remove the depressed center wheel, simply

reverse the above-mentioned procedure.

Depressed center

wheel

Push

button

Wrench

Wheel guard

Wheel washer

Spindle

Wheel nut

Fig. 9

Tighten

15° – 30°

01Eng_G14DSL_US 8/28/13, 16:2717

English

When installing the carbon brush, choose the

direction so that the nail of the carbon brush agrees

with the contact portion outside the brush tube.

Then push it in with a finger as illustrated in Fig.

13. Lastly, install the brush cap.

Fig. 12

CAUTION:

●

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush

tube. (You can insert whichever one of the two

nails provided.)

●

Caution must be exercised since any error in this

operation can result in the deformed nail of the

carbon brush and may cause motor trouble at an

early stage.

MAINTENANCE AND INSPECTION

WARNING: 䢇

Be sure to turned off the switch and pull out the battery.

䢇

Using cracked, deformed or damaged wheels can lead to wheel breakage and resulting

serious injury.

1. Replacing the depressed center wheel

Replace the depressed center wheel when it has

been worn out to about 2-3/8" (60mm) in external

diameter. Confirm that there is no crack or any

damage to the depressed center wheel. If there is

a crack or a transformation in the wheel, replace it

immediately.

2. Check the Screws

Loose screws are dangerous. Regularly inspect

them and make sure they are tight.

CAUTION:

Using this power tool with loosened screws is

extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 10)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn

carbon brush can result in motor trouble, replace

the carbon brush with new ones when it becomes

worn to or near the “wear limit”. In addition,

always keep carbon brushes clean and ensure that

they slide freely within the brush holders.

NOTE:

When replacing the carbon brush with a new one,

be sure to use the Hitachi Carbon Brush Code No.

999054.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 12.

Fig. 10

Wear limit

0.12" (3 mm)

0.45"

(11.5 mm)

Fig. 11

Nail of carbon brush

Protrusion of

carbon brush

Fig. 13

Contact portion outside

brush tube

01Eng_G14DSL_US 8/28/13, 16:2718

English

6. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner,

for they may damage the plastics.

7. Disposal of the exhausted battery

WARNING:

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable. At

the end of it’s useful life, under various state and

local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste officials for details in

your area for recycling options or proper disposal.

8. Storage

Storing in a place below 104°F (40°C) and out of

the reach of children.

NOTE:

Make sure that the battery is fully charged when

stored for a long period (3 months or more). The

battery with smaller capacity may not be able to

be charged when used, if stored for a long period.

NOTE:

Storing lithium-ion batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage of batteries with a low charge

may result in performance deterioration,

significantly reducing battery usage time or

rendering the batteries incapable of holding a

charge.

However, significantly reduced battery usage time

may be recovered by repeatedly charging and

using the batteries two to five times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

9. Service and repairs

All quality power tools will eventually require

servicing or replacement of parts because of wear

from normal use. To assure that only authorized

replacement parts will be used, all service and

repairs must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

10. Service parts list

CAUTION:

Repair, modification and inspection of Hitachi

Power Tools must be carried out by an Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance. In the

operation and maintenance of power tools, the

safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest

technological advancements.

Accordingly, some parts (i.e. code numbers and/

or design) may be changed without prior notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when

used with batteries other than these designated

by us, or when the battery is disassembled and

modified (such as disassembly and replacement

of cells or other internal parts).

01Eng_G14DSL_US 8/28/13, 16:2719

English

ACCESSORIES

WARNING:

Never use any accessories other than those mentioned below.

The use of any accessories other than those mentionded below or attachments not intended for use such as

cup wheel, cut-off wheel or saw blade is dangerous and may cause personal injury or property damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

䡬

Depressed center wheel ................................................................................................. 1

4-1/2" (115 mm) external dia. × 1/4" (6 mm) thickness × 7/8"" (22 mm) hole dia

(Code No. 701045 or 326203)

䡬

Wrench (Code No. 938332Z) .......................................................................................... 1

䡬

Side handle (Code No. 318312) ..................................................................................... 1

䡬

Battery charger (UC18YRSL or UC18YFSL) .................................................................. 2

䡬

Battery (BSL1430 : G14DSL) .......................................................................................... 2

(BSL1830 : G18DSL) .......................................................................................... 1

䡬

Battery cover (Code No. 329897) (only G14DSL) ......................................................... 1

䡬

Plastic Case (Code No. 328206) ..................................................................................... 1

Battery, battery charger, plastic case and battery cover are not contained.

G14DSL

(2LSCK)

G18DSL

(LSCK)

G14DSL

G18DSL

(NN)

01Eng_G14DSL_US 8/28/13, 16:2720

La page est en cours de chargement...

Hitachi G 14DSL Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: G 14DSL

Catégorie: Outils électroportatifs

Taper: Safety Instructions And Instruction Manual

Ce manuel convient également à

G 18DSL

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi G 14DSL
español: Hitachi G 14DSL

Hitachi G 14DSL Safety Instructions And Instruction Manual

Ce manuel convient également à

Hitachi G 14DSL Safety Instructions And Instruction Manual

dans d''autres langues

Documents connexes

Autres documents