Walter ICECUT MINI Le manuel du propriétaire

ICECUTTM

Magnetic Drilling Units

ICECUT MINI 39-D 050 (120V)

This machine is CSA certified.

ICECUT MINI Low-Profile Original Instructions 03-2019

2

Thank you for your purchase of the ICECUT MINI low-profile

magnetic drilling unit from Walter.

We would really appreciate your feedback on the machine.

Other related products by Walter:

Contact Walter Surface Technologies

Canada (Toll Free): +1-888-592-5837

USA (Toll Free): +1-866-592-5837

Mexico: (81) 11 12-5875

Email: [email protected]

Or visit: www.walter.com

ICECUT MINI Low-Profile Original Instructions 03-2019

3

TABLE OF CONTENTS

SECTION

PAGE

1)

INTENDED USE

4

2)

GENERAL SAFETY RULES

4

3)

INFORMATION PLATE SYMBOLS

6

4)

SPECIFICATIONS

7

5)

OPERATIONAL SAFETY PROCEDURES

8

6)

OPERATING INSTRUCTIONS

8

7)

CONTROL PANEL OPERATION

9

8)

SPEED SELECTION

10

9)

MAGNET DETECTION

10

10)

EXTENSION CABLE SELECTION

10

11)

MOUNTING OF CUTTERS

11

12)

SOLUTIONS TO HOLE MAKING PROBLEMS

11

13)

TROUBLE SHOOTING

12

14)

MAINTENANCE

13

15)

WARRANTY STATEMENT

15

16)

ICECUT MINI - EXPLODED VIEW OF MACHINE

48

17)

ICECUT MINI - EXPLODED VIEW OF MOTOR

52

18)

ICECUT MINI - CONTROL PANEL & PARTS LIST

53

19)

ICECUT MINI - WIRING DIAGRAM

54

Included with your Magnetic Drill Unit

Ratchet handle

Safety strap

4mm hexagonal wrench (x2)

Coolant bottle

Safety glasses

1 x Pair of Spare carbon brushes – 120V

ICECUT MINI Low-Profile Original Instructions 03-2019

4

1) INTENDED USE

The intended use of this magnetic drill is to drill holes in ferrous metals. The magnet is used to hold the drill in place

whilst the drill is functioning. It is designed for use in fabrication, construction, railways, petrochemical and any other

applications when drilling ferrous metal. Any deviation from its intended use will not be covered by warranty.

2) GENERAL SAFETY RULES

WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. When using electric tools basic safety precautions should

always be followed to reduce the risk of fire, electric shock and personal injury. Failure to follow all instructions

listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or

dust. Power tools create sparks which may ignite the dust or fumes.

3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose

control.

ELECTRICAL SAFETY

1. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes

and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor

plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If

the tools should electrically malfunction or break down, grounding provides a low resistance path to carry

electricity away from the user.

2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is grounded.

3. Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away

from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the

risk of electric shock.

5. When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W". These cords are

rated for outdoor use and reduce the risk of electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tools

when tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating

power tools may result in serious personal injury.

2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

3. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch

or plugging in tools that have the switch on invites accidents.

4. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a

rotating part of the tool may result in personal injury.

5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better

control of the tool in unexpected situations.

6. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat or hearing

protection must be used for appropriate conditions.

ICECUT MINI Low-Profile Original Instructions 03-2019

5

TOOL USE AND CARE

1. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work

by hand or against your body is unstable and may lead to loss of control.

2. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at

the rate in which it is designed.

3. Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is

dangerous and must be repaired.

4. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing

the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

5. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of

untrained users.

6. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting

edges are less likely to bind and are easier to control.

7. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect

the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

8. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be

suitable for one tool, may become hazardous when used on another tool.

9. Always use safety strap. Mounting can release.

SERVICE

1. Tools service must be performed only by qualified repair personnel. Service or maintenance performed by

unqualified personnel could result in a risk of injury.

2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of

this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric

shock or injury.

ADDITIONAL IMPORTANT SAFETY NOTES

1. Remove the power supply before carrying out any adjustment, servicing or maintenance.

2. Consider work area environment;

 Do not expose tools to rain.

 Do not use tools in damp or wet locations.

 Keep work area well lit (500 Lux recommended).

 Do not use tools in the presence of flammable liquids or gases.

 Ensure there is adequate space to gain access to the plug, mains and motor on/off switches.

3. Guard against electric shock:

 Avoid body contact with earthed or ground surfaces (e.g. pipes, radiators, cookers and refrigerators). Electric

safety can be further improved by using a high-sensitivity (30 m A/0.1s) residual current device (RCD).

4. Keep other persons away. Do not let untrained persons, especially children, touch the tool or the extension cord

and keep them away from the work area.

5. Store idle tools when not in use. All tools should be stored in a dry locked-up place, out of reach of children.

6. When using the drill, always ensure a safe operating distance from any swarf and do not reach into the cutting

area, or near the cutter, when the machine is running.

7. Connect dust extraction and collecting equipment, if devices are provided, ensuring these are properly connected

and used.

8. Do not overreach! Keep proper footing and balance at all times.

9. Maintain tools with care;

 Keep cutting tools sharp and clean for better and safer performance.

 Regularly check the machine for any wear or damage.

 Ensure the machine is clean and free from debris prior to use.

 Remove from the mains prior to any maintenance.

 Follow instructions for lubricating and changing accessories.

ICECUT MINI Low-Profile Original Instructions 03-2019

6

 Inspect tool cords periodically and if damaged have it repaired by an authorized Walter service facility.

 Inspect extension cords periodically and replace if damaged.

 Keep handles dry, clean and free from oil and grease.

10. Disconnect tools from the power supply when not in use, before servicing or when changing accessories such as

cutters.

11. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.

12. Use extension leads only intended for outdoor use when the tool is used outdoors.

13. The vibration emissions during actual use can differ from the declared total value depending on the ways in which

the tool is being used.

14. Watch what you are doing, use common sense and do not operate the tool when you are tired. Do not operate the

machine when under the influence of alcohol or any illegal substances.

15. Check damaged parts

 Before further use of tool, it should be carefully checked to determine that it will operate property and

perform its intended function.

 Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other

conditions that may affect its operation.

 A guard or other part that is damaged should be properly repaired or replaced by an authorized service centre

unless otherwise indicated in this instruction manual.

 Have defective switches replaced by authorized service centre,

 Do not use the tool if the switch does no turn it on and off.

16. The use of any accessory or attachment, other than ones recommended in this instruction manual, may present a

risk of personal injury.

17. Have your machine repaired by a qualified Walter technician. This electric tool complies with the relevant safety

rules. Qualified persons using original spare parts should only carry out repairs otherwise this may result in

considerable danger to the user.

18. Never operate the machine if parts are missing or damaged.

19. Never direct jets of water or flammable liquids over the drill.

20. Operator must be physically able to handle the weight of the machine.

21. Operator should be trained in the use of the machine.

3) INFORMATION PLATE SYMBOLS

1

1 2 3 4

1. Refer to the user manual for operational and safety issues with regard to this machine.

2. Dispose of the machine and electrical components correctly.

3. Eye protection must be worn when operating the machine.

4. Ear defenders must be worn when operating the machine.

ICECUT MINI Low-Profile Original Instructions 03-2019

7

4) SPECIFICATIONS

Maximum hole cutting capacity in .2/.3C steel (Ø X DoC) = 2” x 2”

Arbor bore = 3/4” (19.05mm) Weldon

Motor Unit

Voltages

120V 50-60Hz

Normal full load

10 A

Electro Magnet

0.53 A

Size

192mm long

82mm wide

Holding Force at 20°C with 25mm minimum plate thickness

The use on any material less than 25mm thick will progressively

reduce the magnetic performance. If possible, substitute

material should be positioned under the magnet and work

piece to equate to a suitable material thickness. If this is not

possible, an alternative secure method of restraining the

machine must be used.

10000N

Overall Dimensions

Height - minimum

179mm

Width (including capstan fitting)

100mm

Length Overall (including guard)

334mm

Net Weight

11 kg (24.2lbs)

Icecut MINI – 120V (39-D 050)

Ear and eye defenders must be worn when operating this machine. Wear gloves to protect hands when operating the

machine.

The declared vibration total value has been measured in accordance with a standard test method and may be used for

comparing one tool with another.

The declared vibration total value may also be used in a preliminary assessment of exposure.

The vibration emission during actual use of the power tool can differ from the declared total value depending on the

ways in which the tool is used;

The need to identify safety measures to protect the operator that are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the operating cycle such as the time and when the tool is switched off

and when it is running idle in addition to the trigger time).

These tools are UK designed and manufactured with globally sourced components and conform with the requirements

of EEC Document HD.400.1 and BS.2769/84.

Suitable only for a single phase 50-60Hz A.C. power supply

DO NOT USE ON D.C. SUPPLY

Do not use your magnetic drill on the same structure when arc welding is in progress.

D.C. current will earth back through the magnet and cause irreparable damage.

WARNING: THIS APPLIANCE MUST BE EARTHED!

NB: ANY MODIFICATIONS TO THIS MACHINE WILL INVALIDATE THE GUARANTEE

ICECUT MINI Low-Profile Original Instructions 03-2019

8

5) OPERATIONAL SAFETY PROCEDURES

READ BEFORE USING THE MACHINE

 When using electrical tools, basic safety precautions should always be followed to reduce the risk of electric shock, fire and

personal injury.

 Ensure the magnet is off before plugging in the machine.

 Do not use in wet or damp conditions. Failure to do so may result in personal injury.

 Do not use in the presence of flammable liquids, gases or in high risk environments. Failure to do so may result in personal

injury.

 Before activating the machine, inspect all electrical supply cables (including extension leads) and replace if damaged. Do not use

if there are any signs of damage.

 Only use extension cables approved for site conditions.

 Before activating the machine, always check the correct function of all operational systems, switches, magnet etc.

 Before operating, the machine must be securely restrained to a fixed independent feature by using safety strap and stationary

rings. Affix the stationary rings into the magnet, uppermost side hole to reduce the potential free movement. Should the

magnet become detached from the work piece. Failure to do so may result in personal injury.

 Always wear approved eye protectors, ear defenders and recommended PPE when operating the machine.

 Disconnect from power source when changing cutters or working on the machine.

 Cutters and swarf are sharp, always ensure that hands are adequately protected when changing cutters or removing swarf. Use

a tool or brush where necessary to remove any swarf or the cutter from the arbor.

 Before operating the machine, always ensure cutter-retaining screws are secured tightly.

 Regularly clear the work area and machine of swarf and dirt, paying particular attention to the underside of the magnet base.

 Always remove tie, rings, watches and any loose adornments that might entangle with the rotating machinery before operating.

 Always ensure that long hair is securely enclosed by an approved restraint before operating the machine.

 Should the cutter become stuck in the work piece, stop the motor immediately to prevent personal injury. Disconnect from

power source and turn arbor to and fro. Do not attempt to free the cutter by switching the motor on and off. Wear safety

gloves to remove the cutter from the arbor.

 If the machine is accidentally dropped, always thoroughly examine the machine for signs of damage and check that it functions

correctly before resuming drilling.

 Regularly inspect the machine and check for any damaged or loose parts.

 Always ensure when using the machine in an inverted position that only the minimum amount of coolant is used and that care

is taken to ensure that coolant does not enter the motor unit.

 Cutting tools may shatter, always position the guard over the cutter before activating the machine. Failure to do so may result in

personal injury.

 On completion of the cut, a slug will be ejected.

 When not in use always store the machine in a safe and secure location.

 Always ensure that approved WALTER agents conduct repairs.

6) OPERATING INSTRUCTIONS

 Keep the inside of the cutter clear of swarf. It restricts the operating depth of the cutter.

 Ensure that the coolant bottle contains sufficient cutting oil to complete the required operating duration. Refill as required.

 Occasionally depress the pilot to ensure cutting fluid is being correctly metered.

 To start the machine, follow the control panel operation instructions. The ICECUT machine is fitted with a dual motor protection

system to fully ensure safety and extended life of the motor. The ACCUDRILLTM protection (found on both sides of the machine)

gives a clear and visible indication to the user of torque being applied to the motor, once the prescribed level is reached the

motor is protected by automatic cut out. To re-start your machine, the operator will simply press the start button again. If,

however the speed controller protection is activated, this is torque sensor regulated at a pre-determined value above

ACCUDRILLTM (should ACCUDRILLTM fail to operate) the operator is required to press the start button twice to re-activate the

machine.

 Always switch off the motor by depressing the green start/stop button or blue button depending upon operation. Do not switch

off the motor by pressing the magnet switch.

 Apply light pressure when commencing the cut of a hole until the cutter is introduced into the work surface. Pressure can then

be increased sufficiently to load the motor. Excessive pressure is undesirable, it does not increase the speed of penetration and

will cause the safety overload protection device to stop the motor (the motor can be restarted by operating the motor start

button) and may cause excessive heat which may result in inconsistent slug ejection

 Always ensure that the slug has been ejected from the previous hole before commencing to cut the next.

 If the slug sticks in the cutter, move the machine to a flat surface, switch on the magnet and gently bring the cutter down to

make contact with the surface. This will usually straighten a cocked slug and allow it to eject normally.

 Apply a small amount of light oil lubricant regularly to the slide.

 Cutter breakage is usually caused by insecure anchorage or a loosely fitting slide (Refer to routine maintenance instructions).

 Only use approved cutting fluid. Walter cutting fluid has been specially formulated to maximise the cutters performance.

ICECUT MINI Low-Profile Original Instructions 03-2019

9

7) CONTROL PANEL OPERATION

ACCUDRILL™ Technology

Designed for you to get the most out of your machine

and your cutters. ACCUDRILL has an easy to read panel

that indicates when you are drilling with too much force,

which will damage the machine and the cutters.

Allow the cutter to do the work and you will find that a

much smoother hole and faster drilling time is achieved.

Green Zone

Perfect, try to keep in

the green zone for

the best cut and

optimum machine

performance.

Red Zone

Overload: Back off

immediately as too

much force will cause

the motor to cut off if

you continue.

Yellow Zone

A little too much

pressure on the drill,

ease off to get back

to the green zone.

ICECUT MINI Low-Profile Original Instructions 03-2019

10

8) SPEED SELECTION

The ICECUT MINI is fitted with a 1-speed gearbox with a variable speed selector.

The speed selection dial is used to reduce the output speed when using larger cutters.

Speed Selector

Position

Speed Controller Setting

Position 1

Position 2

Position 3

Position 4

Position 5

Position 6

RPM

250/min

300/min

350/min

400/min

450/min

500/min

9) MAGNET DETECTION

It is advised that when working on thin material a packing piece should be used to increase the

material thickness under the magnet. Working on thin material without a packing piece will reduce

the magnet holding force.

It is advised that the drill is to be operated on ferrous material 12mm thick and above. Damage to

the magnet base, such as pitting, will affect the strength of the magnet holding force.

10) EXTENSION CABLE SELECTION

The machines are factory fitted with a 3 metre length of cable having three conductors 1.5mm²

LIVE, NEUTRAL and EARTH. If it becomes necessary to fit an extension cable from the power

source, care must be taken in using a cable of adequate capacity. Failure to do so will result in a

loss of traction by the magnet and a reduction of power from the motor.

Assuming a normal AC supply of the correct voltage, it is recommended that the following

extension lengths shall not be exceeded:

For 120V supply: 3 metres (11.5 feet) of 3 core x 14AWG

ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE CHANGING CUTTERS.

ICECUT MINI Low-Profile Original Instructions 03-2019

11

11) MOUNTING OF CUTTERS

 The machine has been made to accept cutters having 19.05mm (3/4”) dia. Weldon shanks.

The following procedure is to be used when mounting cutters:

 Lay the machine on its side with feed handles uppermost, ensuring arbor is wound down to

its lowest point to enable access to socket screws 48S217.

 Take appropriate pilot and place through the hole in cutter shank. Insert shank of cutter

into bore of arbor, ensuring alignment of two drive flats with socket screws.

 Tighten both screws using hexagon key.

12) SOLUTIONS FOR HOLE MAKING PROBLEMS

Problem

Cause

Remedy

1) Magnetic base

won’t hold

effectively

Material being cut may be too thin for efficient

holding.

Swarf or dirt under magnet.

Irregularity on magnet contact or work-piece.

Insufficient current going to magnet during drilling

cycles.

Attach an additional piece of metal under the magnet, or

mechanically clamp magnetic base to work-piece.

Clean magnet.

Use extreme care; file any imperfections flush to surface.

Confirm power supply and output from control unit, check supply

cable.

2) Cutter skips

out of centre-

punch mark at

initiation of cut

Magnetic base is not holding effectively.

Worn arbor bushing and/or ejector collar.

Too much feed pressure at start of cut.

Cutter is dull, worn, chipped or incorrectly sharpened.

Poor centre-punch mark; weak pilot spring; pilot not

centred in centre-punch mark.

Worn or bent pilot, worn pilot hole.

Loose bolts on motor bushing support bracket, main

casting or loose gib adjusting set screws.

See causes and remedies above.

New arbor bushing is needed.

Light pressure only is needed until a groove is cut. The groove

then serves as a stabilizer.

Replace or re-sharpen. Sharpening service is available.

Improve centre-punch and/or replace worn parts

Replace part or parts

Adjust where necessary

3) Excessive

drilling pressure

required

Incorrectly re-sharpened, worn or chipped cutter.

Coming down on swarf lying on surface of work-

piece.

Gib strips out of adjustment or lack of lubrication.

Swarf accumulated (packed) inside cutter.

Re-sharpen or replace.

Take care not to start a cut on swarf.

Adjust setscrews and lubricate.

Clear cutter.

4) Excessive

cutter breakage

Steel swarf or dirt under cutter.

Incorrectly re-sharpened or worn cutter.

Cutter skipping.

Slide needs adjustment.

Remove cutter, clean part thoroughly and replace.

Always have a new cutter on hand to refer to for correct tooth

geometry, together with instruction sheet.

See causes and remedies (2).

Tighten grub screws supporting the slide.

ICECUT MINI Low-Profile Original Instructions 03-2019

12

Cutter not attached tightly to arbor.

Insufficient use of cutting oil or unsuitable type of oil.

Incorrect speed

Retighten.

Inject oil of light viscosity into the coolant-inducing ring and check

that oil is being metered into cutter when pilot is depressed. If

not, check pilot groove and arbor internally for dirt or apply oil

externally. (Even a small amount of oil is very effective).

Ensure correct gear is used for the cutter.

5) Excessive

cutter wear

See cause and remedy above

Incorrectly re-sharpened cutter.

Insufficient or spasmodic cutting pressure.

Refer to instructions and a new cutter for proper tooth geometry.

Use sufficient steady pressure to slow the drill down. This will

result in optimum cutting speed and chip load.

13) TROUBLESHOOTING

Magnet and motor do not function

- Damaged or defective wiring

- Defective fuse

- Defective control unit

- Defective power supply

Magnet does function, the motor does

not

- Damaged or defective wiring

- Carbon brushes are stuck or worn out

- Defective on / off switch

- Defective control unit

- Defective armature and/or field

- Defective protective reed switch

Hole cutters break quickly, holes are

bigger than the hole cutter

- Play in the guide

- Bent spindle

- Shaft extending from the motor is bent

- Pilot bent

Motor running roughly and/or seizing up

- Bent spindle

- Shaft extending from the motor is bent

- Triangular guide not mounted straight

- Dirt between spindle and triangular guide

Motor making a rattling sound

- Gear ring (bottom of the armature) worn out

- Gear(s) worn out

- No grease in gear box

Motor humming, big sparks and motor

has no force

- Armature damaged

- Field burned

- Carbon brushes worn out

Motor does not start or fails.

- Damaged or defective wiring

- Damage to armature or field coil

- Damaged or defective brushes

Guiding takes a great deal of effort

- Guide is set too tight

- Guide is dry

- Guide/gear- rack/rotation system is dirty or damaged

Insufficient magnetic force

- Bottom of magnet not clean and dry

- Bottom of magnet not flat

- Work piece is not bare metal

- Work piece is not flat

- Work piece is too thin less than 3.5mm

- Defective control unit

- Defective magnet

ICECUT MINI Low-Profile Original Instructions 03-2019

13

14) MAINTENANCE

In order to get the best life out of your Walter machine always keep it in good working order.

A number of items must always be checked on Walter machines.

Always before starting any job make sure the machine is in good working order and that there are no

damaged or loose parts. Any loose parts must be tightened.

Before proceeding with any maintenance work be certain that the power supply is disconnected.

Description

Every operation

1 week

1 Month

Visual check of machine for damage

X

Operation of machine

X

Check brush wear

X

Check magnetic base

X

Check alignment of the machine

X

Check grease

X

Check armature

X

Visually check the machine for damage.

The machine must be checked before operation for any signs of damage that will affect the operation of the

machine. Particular notice must be taken to the mains cable, if the machine appears to be damaged it should

not be used, failure to do so may cause injury or death.

Check operation of the machine.

The machines operation must be checked to ensure that all components are working correctly.

Machine Brushes

Should be checked to make sure there is no abnormal wear present (this should be checked at least once a

week if used frequently). If the brush has worn more than 2/3 of the original length, the brushes should be

changed. Failure to do so may cause damage to the machine.

Magnetic base

Before every operation the magnetic base should be checked to make sure that there is no damage present.

An uneven magnet base will cause the magnet not to hold as efficiently and may cause injury to the

Frame under voltage

- Damaged / defective wiring

- Motor seriously dirty

Fuse blows when magnet switch is

turned on

- Damaged or defective wiring

- Wrong value fuse

- Defective magnet switch

- Defective control unit

Fuse blows when motor is started up

- Damaged or defective wiring

- Wrong value fuse

- Motor running roughly

- Defective armature and / or field

- Carbon brushes worn out

- Defective control unit

Rotation system free stroke too long

- Loose or defective gear-rack

- Defective rotation system

ICECUT MINI Low-Profile Original Instructions 03-2019

14

operator.

Adjustment of slide and bearing bracket alignment.

An essential requirement of the machine is that the slide can move in a smooth and controlled manner, free

of lateral movement and vibration.

This situation can be maintained by periodic adjustment of the slide and is accomplished in the following

manner:

1. Place the machine in an upright position and, by means of the capstan, raise the slide to its highest

position. Clean the brass gib strips and apply a small amount of light machine oil to the wear

surfaces.

2. Now lower the slide back to its lowest position. Bring the slide into the center of the dovetail slide

housing and loosen screws thus allowing free movement of the arbor support bracket.

3. Commencing with the middle screws, gently feed in all the screws until slight resistance is

encountered.

4. Operate the slide up and down a few times to test the movement and make any further necessary

adjustments. Try to ensure that all the screws are exerting a uniform pressure on the slide from top

to bottom. A perfectly adjusted slide will operate freely up and down without any sideways

movement.

5. Now raise the slide to its highest position. Slightly undo the arbor bearing bracket and, using fingers

only, tighten the screws.

6. Place the machine on a steel plate, connect to power supply and switch on the magnet. Start up the

motor. If the arbor is incorrectly aligned, the arbor support bracket will be seen to oscillate. Make

any necessary further adjustments to the bracket to ensure correct alignment of the spindle and

finally tighten the screws using a spanner. Lastly tighten the arbor bearing bracket.

Check machines grease.

The gearbox grease should be checked once a month to ensure all moving components are covered to

prevent wear. The grease should be changed at least once a year to ensure you gain the best from your

machine.

Check Armature of the machine.

This should be checked at least once a month to check that there are no visual signs of damage to the body

or to the commutator. Some signs of wear will be seen on the commutator over a period of time but this is

normal (this is the part that comes into contact with the brushes) however, if there are any signs of

abnormal damage the part should be replaced.

ICECUT MINI Low-Profile Original Instructions 03-2019

15

15) WARRANTY STATEMENT

Walter warrants its machines to be free from faulty parts, under normal usage of machines, for a period of

12 months from initial date of purchase. All other parts (excluding cutters) are under warranty for 90 days,

provided that the warranty registration card (or online registration) has been completed and returned to

Walter or its designated distributor within a period of (30) days from the purchase date. Failure to do so

will void the warranty. If the stated is adhered to, Walter will repair or replace (at its option) without

charge any faulty items returned.

This Warranty does not cover:

1. Components that are subject to natural wear and tear caused by the use is not in accordance with the

operator’s instructions

2. Defects in the tool caused by non-compliance with the operating instructions, improper use, abnormal

environment conditions, inappropriate operating conditions overload or insufficient servicing or

maintenance.

3. Defects caused by using accessories, components or spare parts other than original Walter parts.

4. Tools to which changes or additions have been made.

5. Electrical components are subject to manufacturer’s warranty.

Your online registration can be submitted at www.walter.com

The warranty claim must be logged within the warranty period. This requires the submission or sending of

the complete tool in question with the original sales receipt which must indicate the purchase date of the

product. A complaint form must also be submitted prior to the return.

This can be found online at www.walter.com.Failure to complete this form will result in the delay of your

claim. All goods returned defective must be returned pre-paid to Walter, in no event shall Walter be

liable for subsequent direct, or indirect loss or damage.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, (EXPRESSED OR IMPLIED) INCLUDING ANY

WARRANTY OF MERCHANTABLITY OR FITNESS FOR A PARTICULAR PURPOSE. WALTER RESERVES THE

RIGHT TO MAKE IMPROVEMENTS AND MODIFICATIONS TO DESIGN WITHOUT PRIOR NOTICE.

“ONLY THE BESTTM”

ICECUT MINI Low-Profile Original Instructions 03-2019

16

ICECUTTM

Perceuses à base magnétique

ICECUT MINI 39-D 050 (120V)

Cette machine est certifiée CSA.

ICECUT MINI Low-Profile Original Instructions 03-2019

17

Nous vous remercions de vous être procuré une perceuse magnétique

à profile bas, ICECUT MINI de Walter.

Nous vous saurions gré de nous faire part de tout

commentaire concernant votre unité.

Autres produits connexes de Walter:

Pour contacter Walter Technologies pour surfaces

Canada (sans frais) : +1 888 592-5837

É.-U. (sans frais) : +1 866 592-5837

Mexique : (81) 11 12-5875

Courriel : [email protected]

Ou visitez le www.walter.com

ICECUT MINI Low-Profile Original Instructions 03-2019

18

TABLE DES MATIÈRES

SECTION

PAGE

1)

APPLICATIONS

19

2)

INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ

19

3)

VIGNETTES D’INFORMATION

21

4)

SPÉCIFICATIONS

22

5)

PROCÉDURES OPÉRATIONNELLES DE SÉCURITÉ

23

6)

INSTRUCTIONS D’UTILISATION

23

7)

OPÉRATIONS DU PANNEAU DE CONTRÔLE

24

8)

SÉLECTION DE VITESSES

25

9)

DÉTECTEUR MAGNÉTIQUE

25

10)

CHOIX DE LA RALLONGE

25

11)

MONTAGE DES FRAISES

26

12)

SOLUTIONS AUX PROBLÈMES DE PERÇAGE

26

13)

DIAGNOSTIC DE PANNE

27

14)

ENTRETIEN

29

15)

GARANTIE

31

16)

ICECUT MINI - VUE EXPLOSÉE DE L’OUTIL

48

17)

ICECUT MINI - VUE EXPLOSÉE DU MOTEUR

52

18)

ICECUT MINI - PANNEAU DE CONTRÔLE ET LISTE DES PIÈCES

53

19)

ICECUT MINI - SCHÉMA DU CÂBLAGE

54

Compris avec votre perceuse magnétique

Poignée à cliquet

Courroie de sécurité

Clé Allen de 4 mm (x2)

Bouteille de liquide de refroidissement

Lunettes de sécurité

Paire de brosses de carbone additionnelle – 120 V

ICECUT MINI Low-Profile Original Instructions 03-2019

19

1) APPLICATIONS

Cette perceuse magnétique est conçue pour les métaux ferreux. L’aimant sert à maintenir la perceuse en place pendant

qu’elle est en fonctionnement. Elle est conçue pour les applications de fabrication, de construction, les applications

ferroviaires ou pétrochimiques et toute autre application qui nécessite de percer des métaux ferreux. Toute utilisation

de la perceuse qui n’est pas énoncée dans les applications prévues ne sera pas couverte par la garantie.

2) INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ

AVERTISSEMENT! LIRE ET COMPRENDRE TOUS LES INSTRUCTIONS. Lire tous les avertissements de sécurité et toutes

les instructions. Ne pas suivre les avertissements et instructions peut donner lieu à un choc électrique, un incendie

et/ou une blessure sérieuse.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES INSTRUCTIONS POUR POUVOIR S’Y REPORTER

ULTÉRIEUREMENT.

SÉCURITÉ DE LA ZONE DE TRAVAIL

1. Conserver la zone de travail propre et bien éclairée. Les zones en désordre ou sombres sont propices aux

accidents.

2. Ne pas faire fonctionner les outils électriques en atmosphère explosive, par exemple en présence de liquides

Inflammables, de gaz ou de poussières. Les outils électriques produisent des étincelles qui peuvent enflammer les

poussières ou les fumées.

3. Maintenir les enfants et les personnes présentes à l'écart pendant l'utilisation de l'outil. Les distractions

peuvent vous faire perdre le contrôle de l'outil.

SÉCURITÉ ELECTRIQUE

1. II faut que les fiches de l'outil électrique soient adaptées au soucie. Ne jamais modifier la fiche de quelque

façon que ce soit. Ne pas utiliser d'adaptateurs avec des outils à branchement de terre. Des fiches non modifiées

et des soucies adaptes réduiront le risque de choc électrique.

2. Éviter tout contact du corps avec des surfaces reliées à la terre telles que les tuyaux, les radiateurs, les

cuisinières et les réfrigérateurs. Il existe un risque accru de choc électrique si votre corps est relié a la terre.

3. Ne pas exposer les outils à la pluie ou à des conditions humides. La pénétration d'eau à l’intérieur d'un outil

augmentera le risque de choc électrique.

4. Ne pas maltraiter le cordon. Ne jamais utiliser le cordon pour porter, tirer ou débrancher l'outil. Maintenir le

cordon à l'écart de la chaleur, du lubrifiant, des arêtes ou des parties en mouvement. Des cordons endommages

ou emmêlés augmentent le risque de choc électrique.

5. Lorsqu'on utilise un outil à l'extérieur, utiliser un prolongateur adapté à l'utilisation extérieure. L'utilisation d'un

cordon adapté à l'utilisation extérieure réduit le risque de choc électrique.

6. Si l'usage d'un outil dans un emplacement humide est inévitable, utiliser une alimentation protégée par un

dispositif à courant différentiel résiduel (RCD). L'usage d'un RCD réduit le risque de choc électrique.

SÉCURITÉ DES PERSONNES

1. Rester vigilant, regarder ce que vous êtes en train de faire et faire preuve de bon sens dans votre utilisation de

l'outil. Ne pas utiliser un outil lorsque vous êtes fatigué ou sous l'emprise de drogues, d'alcool ou de

médicaments. Un moment d'inattention en cours d'utilisation d'un outil peut entrainer des blessures graves des

personnes.

2. Utiliser un équipement de sécurité. Toujours porter une protection pour les yeux. Les équipements de sécurité

tels que les masques contre les poussières, les chaussures de sécurité antidérapantes, les casques ou les

protections acoustiques utilisées pour les conditions appropriées réduiront les blessures de personnes.

3. Éviter tout démarrage intempestif. S'assurer que l'interrupteur est en position arrêt avant de brancher l'outil au

secteur et/ou au bloc de batteries, de le ramasser ou de le porter. Porter les outils en ayant le doigt sur

l’interrupteur ou brancher des outils dont l'interrupteur est en position marche est source d'accidents.

4. Retirer toute clé de réglage avant de mettre l'outil en marche. Une clé laissée fixée sur une partie tournante de

l'outil peut donner lieu à des blessures de personnes.

5. Ne pas se précipiter. Garder une position et un équilibre adaptés à tout moment. Cela permet un meilleur

contrôle de l'outil dans des situations inattendues.

ICECUT MINI Low-Profile Original Instructions 03-2019

20

6. S'habiller de manière adaptée. Ne pas porter de vêtements amples ou de bijoux. Garder les cheveux, les

vêtements et les gants à distance des parties en mouvement. Des vêtements amples, des bijoux ou les cheveux

longs peuvent être pris dans des parties en mouvement.

7. Si des dispositifs sont fournis pour le raccordement d'équipements pour l'extraction et la récupération des

poussières, s'assurer qu'ils sont connectés et correctement utilisés. Utiliser des collecteurs de poussière peut

réduire les risques dus aux poussières.

UTILISATION ET ENTRETIEN DE L’OUTIL

1. Ne pas forcer l'outil. Utiliser l'outil adapté à votre application. L'outil adapté réalisera mieux le travail et de

manière plus sûre au régime pour lequel il a été construit.

2. Ne pas utiliser l'outil si l'interrupteur ne permet pas de passer de l'état de marche à arrêt et vice versa. Tout

outil qui ne peut pas être commande par l'interrupteur est dangereux et il faut le réparer.

3. Débrancher la fiche de la source d'alimentation en courant et/ou le bloc de batteries de l'outil avant tout

réglage, changement d'accessoires ou avant de ranger l'outil. De telles mesures de sécurité préventives

réduisent le risque de démarrage accidentel de l'outil.

4. Conserver les outils à l'arrêt hors de la portée des enfants et ne pas permettre à des personnes ne connaissant

pas l'outil ou les présentes instructions de le faire fonctionner. Les outils sont dangereux entre les mains

d'utilisateurs novices.

5. Observer la maintenance de l'outil. Vérifier qu'iI n'y a pas de mauvais alignement ou de blocage des parties

mobiles, des pièces cassées ou toute autre condition pouvant affecter le fonctionnement de l'outil. En cas de

dommages, faire réparer l'outil avant de l'utiliser. De nombreux accidents sont dus à des outils mal entretenus.

6. Garder affûtés et propres les outils permettant de couper. Des outils destinés à couper correctement entretenus

avec des pièces coupantes tranchantes sont moins susceptibles de bloquer et sont plus faciles à contrôler.

7. Utiliser l'outil, les accessoires et les lames etc., conformément à ces instructions, en tenant compte des

conditions de travail et du travail à réaliser. L'utilisation de l'outil pour des opérations différentes de celles

prévues pourrait donner lieu à des situations dangereuses.

MAINTENANCE ET ENTRETIEN

1. Faire entretenir l'outil par un réparateur qualifié utilisant uniquement des pièces de rechange identiques. Cela

assurera le maintien de la sécurité de l'outil.

AUTRE NOTES IMPORTANT SUR LE SECURITE

Coupez l’alimentation avant de procéder à tout réglage ou entretien de la perceuse.

1. Conservez l’aire de travail dégagée. Une aire encombrée augmente le risque de blessures.

2. Conditions à considérer :

• Protégez les outils de la pluie;

• Utilisez les outils dans des endroits secs;

• Assurez-vous de bien éclairer votre aire de travail (nous recommandons 500 lux.);

• Tenez tout liquide ou gaz inflammable à l’écart de vos outils;

• Assurez-vous d’avoir un accès facile à la prise de courant, à l’interrupteur principal et à ceux du moteur.

3. Prévention des décharges électriques : Évitez le contact physique avec les surfaces reliées à la terre (par exemple :

un tuyau, un radiateur, une cuisinière, un réfrigérateur). La sécurité électrique peut être accrue en utilisant un

dispositif à courant résiduel à grande sensibilité (30 m A/0,1 s).

4. Gardez toute personne à l’écart de l’aire de travail! Ne laissez pas une personne non qualifiée, plus particulièrement un

enfant, toucher l’outil ou le câble de rallonge.

5. Rangez les outils dont vous ne vous servez pas dans un endroit sec, loin de la portée des enfants. Verrouillez-le.

6. Ne forcez pas la perceuse. Elle fonctionnera mieux et sera plus sécuritaire si vous l’utilisez convenablement.

7. Utilisez le bon outil :

▪ Utilisez des outils robustes pour effectuer des travaux importants;

▪ Utilisez cet outil seulement selon son utilisation prévue. Par exemple, n’utilisez pas la perceuse pour la coupe de

bois.

8. Portez des vêtements adéquats :

▪ Laissez les vêtements amples et les bijoux de côté, ils pourraient se prendre entre les pièces mobiles;

▪ Portez des chaussures à semelles antidérapantes lorsque vous travaillez à l’extérieur;

La page est en cours de chargement...

Walter ICECUT MINI Le manuel du propriétaire

Walter ICECUT MINI Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents