Intermec MobileLAN access WA21 Guide de démarrage rapide

Marque: Intermec

Modèle: MobileLAN access WA21

Taper: Guide de démarrage rapide

Intermec’s MobileLAN™access family of access points delivers reliable and seamless

wireless performance in almost any operational environment. The MobileLAN access

WA21 can be powered either by AC power or by power over Ethernet to make installation

easier. It is designed for standards-based connectivity and it may have up to two of the

following radios installed:

• IEEE 802.11a

• IEEE 802.11g

The WA21 with an IEEE 802.11a radio installed is Wi-Fi

certified

for interoperability with other 802.11a wireless LAN devices.

The WA21 with an IEEE 802.11g radio installed is Wi-Fi certified

for interoperability with other 802.11g and 802.11b wireless

LAN devices.

This quick start guide supports the WA21B and helps you to understand its ports and

LEDs. You can also use this quick start guide to get an overview of how to install the

WA21, how to connect the WA21 to power and to your network, and how to use the

MobileLAN access Utility to configure its IP address. Once you assign the WA21 an IP

address, you can continue configuring it using a web browser interface or a telnet

session.

For complete instructions on how to install, operate, configure, maintain, and

troubleshoot your WA21, see the MobileLAN access WA2X System Manual (P/N 073915). Please

visit the Intermec web site at www.intermec.com to download this manual and other

current manuals in PDF. Or, you can order printed documentation from your local

Intermec representative.

Out of the Box

MobileLAN

™

access WA21

Heading 1

About the WA21

Safety First

Quick Start Guide

Specifications

Note: The WA21 does not ship with an antenna (except for one 802.11a

configuration that ships with non-removable antennas). For a list of antennas

and antenna accessories, see the MobileLAN access WA2X System Manual or contact

your local Intermec representative.

MobileLAN access WA21 Quick Start Guide

*074744-002*

P/N 074744-002

Physical dimensions 9.5 cm x 23.6 cm x 35.5 cm

(3.75 in x 9.3 in x 14.0 in)

AC electrical rating

Standard ~100 to 240 V, 1.0 to 0.5A, 50 to 60 Hz

Heater (optional) ~100 to 120 V, 1.0A, 50 to 60 Hz

or ~200 to 240 V, 0.5A, 50 to 60 Hz

Power over Ethernet

electrical rating x 48V, 315 mA

Environmental rating IP54

Operating temperature

Standard -25°C to 70°C (-13°F to 158°F)

Heater (optional), AC only -30°C to 70°C (-22°F to 158°F)

Heater/insulated bag

(optional), AC only -30°C to 0°C (-22°F to 32°F)

Storage temperature -40°C to 70°C (-40°F to 158°F)

Humidity 10 to 90%, non-condensing

Patent information

Product is covered by one or more of the following patents: 4,910,794; 5,070,536; 5,295,154;

5,349,678; 5,394,436; 5,425,051; 5,428,636; 5,483,676; 5,504,746; 5,546,397; 5,574,979; 5,592,512;

5,680,633; 5,682,299; 5,696,903; 5,740,366; 5,790,536; 5,844,893; 5,862,171; 5,940,771; 5,960,344.

There may be other U.S. and foreign patents pending.

Government regulatory agencies require that this access point only use approved

antennas. Therefore, this access point uses a custom antenna connector. Do not use

antennas not approved for use with this access point.

Attention: Les organismes de réglementation gouvernementaux exigent que ce

point d’accès. Par conséquent, le point d’accès est doté d’un connecteur d’antenne

personnalisé. N’utilisez pas des antennes qui ne sont pas approuvées.

The WA21 without the internal power supply option is intended to be powered only

from an Ethernet host that complies with the IEEE 802.3af specification for power

over Ethernet (POE).

Attention: Le WA21 sans option de source d’alimentation interne est conçu pour être

alimenté à partir d’un hôte Ethernet qui est conforme à la spécification IEEE 802.3af

pour l’alimentation par Ethernet (POE, de l’anglais Power Over Ethernet).

The WA21 with the internal power supply option may be connected either to a

standard Ethernet port or to a powered Ethernet host that complies with the IEEE

802.3af specification for power over Ethernet.

Attention: Le WA21 avec option de source d’alimentation interne peut être connecté

soit à un port Ethernet standard, soit à un hôte Ethernet alimenté qui est conforme à

la spécification IEEE 802.3af pour l’alimentation par Ethernet.

When the WA21 is connected to a powered Ethernet host, both the AC power cord

and the Ethernet cables must be disconnected prior to servicing.

Attention: Lorsque le WA21 est connecté à un hôte Ethernet alimenté, le cordon

d’alimentation CA et les câbles Ethernet doivent tous être débranchés avant tout

entretien ou dépannage.

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org).

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).

AC power cord

(optional)

Document

package

MobileLAN

access Tools CD

MobileLAN

access WA21

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

2005 Intermec Technologies

Click the down arrow and

choose Set IP Address.

Enter the Ethernet MAC

address of the access point

(printed on the label on the

access point).

Enter the new IP address of

the access point.

Defining the LEDs and Ports

MobileLAN

™

access WA21 Quick Start Guide

To access the WA21 ports, unscrew the two thumbscrews that are on the front of the

cable access door and then remove the door.

Mounting the WA21 Connecting the WA21

Attach antennas to the WA21. Intermec offers a variety of antennas and antenna

accessories. For a complete list, see the MobileLAN access WA2X System Manual.

Connect the WA21 to your network. You can either use an Ethernet cable to

connect the Ethernet port to an Ethernet drop or you can use the fiber optic port

option. For help connecting the WA21 to a fiber optic network, see “Connecting to

Your Fiber Optic Network” in the MobileLAN access WA2X System Manual.

Connect the WA21 to power. You can either use an AC power cord or the power

over Ethernet option. To use power over Ethernet, you use an Ethernet cable to

connect the Ethernet port to a MobileLAN power bridge, a Cisco power bridge, or

another 802.3af-compliant power bridge. For help, see the documentation that

shipped with your power bridge.

Setting an Initial IP Address

Checking for Software Upgrades

You should check the Intermec web site for the most up-to-date software downloads and

documentation.

At www.intermec.com, click Service & Support. The Intermec Global Sales & Service

window appears.

From the Task Menu, click Downloads.

From the Select A Product field, choose Network: MobileLAN™ access WA21. A

screen appears with a table of available software for the WA21.

Click the software you want to download. Follow the prompts to download the

files to your PC. For help upgrading your access point software, follow the

instructions in the MobileLAN access WA2X System Manual.

To check for the latest documentation, from the Task Menu, click Manuals.

From the Select A Product field, choose Network: MobileLAN™ access WA21. A

screen appears with a list of available manuals for the WA21.

Click the manual you would like to view (in PDF). Or, to order printed versions of

Intermec manuals, contact your local Intermec representative.

You can place the WA21 either horizontally or vertically on a stable surface. You can also

mount the WA21 to a wall or a beam using one of these mounting bracket kits:

• Mounting bracket kit (P/N 068918)

• Rotating mounting bracket kit (P/N 068751)

Depending on your operating temperature needs and power, you can use these options:

Install the MobileLAN access Utility on your PC by inserting the enclosed CD,

clicking Install Software, and following the instructions that appear on your

screen. You can also download the software from the Intermec web site.

Note: Your PC must be on the same Ethernet segment as the access

point. Or, if your PC is communicating wirelessly with the access point,

you must have an active radio connection.

Start the utility.

Configure parameters A through C. See the screen to the right.

Reboot the access point by disconnecting it from and reconnecting it to a power

source.

Immediately click Set. The Status box lets you know when the new IP address is

successfully set.

Congratulations!

Your wireless end devices can now begin transmitting data packets through the WA21 to

your wired network. To continue configuring the access point, from the Actions menu

choose Configure Access Point. Your web browser application (for example, Internet

Explorer) starts and the Access Point Login screen appears.

power

Ethernet

connection

Antennas

-25

C to 70

(-13

F to 158

-30

C to 70

(-22

F to 158

Use a mounting

bracket kit to

mount the WA21

with heater option

so that the LEDs

face down.

-30

C to 0

(-22

F to 32

Place the WA21 with heater

option in an insulated bag

(P/N 068216) before using a

mounting bracket kit.

Wall

Power

port

(optional)

Serial

port

Power

Remains on

after the

WA21 boots.

Wireless #1

Flashes when a frame is

transmitted or received on

the radio port for the radio

installed in radio slot 1.

Wired LAN

Flashes when a

frame is transmitted

or received on the

Ethernet port.

Ready-to-Work™ Indicator

Blue LED flashes if the WA21 is

searching for the root access

point in the network. Remains on

when the access point is ready for

use, indicating that it either found

a root or became the root.

Wireless #2

Flashes when a frame is

transmitted or received on

the radio port for the radio

installed in radio slot 2 (if a

second radio is installed).

Fiber

optic port

(optional)

10BaseT/

100BaseTx

Ethernet port

Cable access

door

Intermec MobileLAN access WA21 Guide de démarrage rapide

Marque: Intermec

Modèle: MobileLAN access WA21

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: Intermec MobileLAN access WA21 Quick start guide

Documents connexes

Autres documents

Seifert 301020 Le manuel du propriétaire