ResMed Humidifier s8 Manuel utilisateur

www.myresmed.com Waking people up to sleep

S8 AutoSet Vantage

™

System

Reorder number: 33887/2 05 06

USER’S MANUAL

English

Français

Español

Português

1

S8 AutoSet Vantage

™

ILLUSTRATIONS / ILLUSTRATIONS /

FIGURAS / ILUSTRAÇÕES

Component of 33887/2 / Partie de 33887/2 /

Componente de 33887/2 / Componente de 33887/2

A

Keypad

Clavier

Teclado

Carry handle

Poignée de transport

Asa para el transporte

Pega de transporte

Air filter cover / Couvercle

du logement du filtre à air /

Cubierta del filtro de aire /

Tampa do filtro de ar

Module

Módulo

DC input

Entrée CC

Entrada de CC

Entrada CC

AC input

Entrée CA

Entrada de CA

Entrada CA

LCD screen

Écran LCD

Visor

Mostrador LCD

Air outlet

Sortie d'air

Salida de aire

Saída de ar

SYSTEM COMPONENTS / COMPOSANTS DU SYSTÈME / COMPONENTES DEL

SISTEMA / COMPONENTES DO SISTEMA

Air inlet

Entrée d'air

Entrada de aire

Entrada de ar

6’6”/2 m

2

34 5

OTHER ACCESSORIES / AUTRES ACCESSOIRES / OTROS ACCESORIOS /

OUTROS ACESSÓRIOS

C

1

5

SETTING UP THE S8

TM

/ INSTALLATION DE LA S8

TM

/

INSTALACIÓN DEL S8

TM

/ MONTAGEM DO S8

TM

D

2

3

4

B

INTEGRATED HUMIDIFIER / HUMIDIFICATEUR INTÉGRÉ / HUMIDIFICADOR

INTEGRADO / HUMIDIFICADOR INTEGRADO

32

9’10”/3 m

1

4

Note: Some products not available in all regions. Remarque : certains de ces produits ne sont pas disponibles dans tous les pays.

Nota: algunos productos no están disponibles en todas las regiones. Nota: alguns produtos não se encontram disponíveis em todas as

regiões.

HumidAire 3i

™

DATA CARD MODULE / MODULE DE CARTE DE DONNÉES /

MÓDULO TARJETA DE DATOS / MÓDULO DE CARTÕES DE DADOS

G

12

H

USING THE DATA CARD / UTILISATION DE LA CARTE DE DONNÉES /

USO DE LA TARJETA DE DATOS / COMO USAR O CARTÃO DE DADOS

1

3

2

Note: Some products not available in all regions. Remarque : certains de ces produits ne sont pas disponibles dans tous les pays.

Nota: algunos productos no están disponibles en todas las regiones. Nota: alguns produtos não se encontram disponíveis em todas as

regiões.

E

HUMIDAIRE 3i AND S8 / HUMIDAIRE 3i ET S8 / EL HUMIDAIRE 3i Y EL S8 /

HUMIDAIRE 3i E S8

BLANK MODULE / MODULE VIERGE / MÓDULO EN BLANCO /

MÓDULO EM BRANCO

F

1

2

Data ccommunications

port

/ Port de

communication des

données / Puerto de

comunicación de

datos / Porta de

comunicação de

dados

HumidAire 3i

USER’S MANUAL 1

M

ANUAL DEL USUARIO 101

M

ANUEL UTILISATEUR 49

M

ANUAL DO UTILIZADOR 153

S8 AUTOSET VANTAGE

™

ENGLISHFRANÇAISPORTUGUÊS ESPAÑOL

33887r2.book Page i Thursday, June 30, 2005 1:36 PM

Protected by patents: AU 691200, AU 697652, AU 709279, AU 724589, AU 730844, AU 736723, AU 750095, AU

750761, AU 764761, EP 0651971, EP 0661071, EP 0920845, EP 0934723, EP 1028769, JP 3580776, NZ 504595, US

4944310, US 5199424, US 5245995, US 5522382, US 5704345, US 6029665, US 6138675, US 6240921, US 6363933,

US 6367474, US 6398739, US 6425395, US 6502572, US 6591834, US 6635021, US 6705315, US 6745768, US

6817361. Other patents pending.

Design registrations pending

S8, HumidAire, HumidAire 3i, AutoSet, S8 AutoSet Vantage, Mirage, Mirage Activa, Mirage Vista, Protégé, Ultra Mirage,

Mirage Swift, and ResScan are trademarks of ResMed Ltd. Papillon is a trademark of MAP Medizin-Technologie GmbH.

Manufactured by:

ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia

Tel: +61 (2) 8884 1000 or 1 800 658 189 (toll free) Fax: +61 (2) 8883 3114 Email: [email protected]

Distributed by:

ResMed Corp 14040 Danielson Street Poway CA 92064-6857 USA

Tel: +1 (858) 746-2400 or 1-800-424-0737 (toll free) Fax: +1 (858) 746-2900 Email: [email protected]

ResMed (UK) Limited 65 Milton Park Abingdon Oxfordshire OX14 4RX UK

Tel: +44 (1235) 862 997 Fax: +44 (1235) 831 336 Email: [email protected]

ResMed Asia Pacific Ltd 97 Waterloo Road North Ryde NSW 2113 Australia

Tel: +61 (2) 9886 5000 or 1 800 991 900 (toll free) Fax: +61 (2) 9889 1471 Email: [email protected]

ResMed BV Nieuwe Parklaan 86, 2587 BV Den Haag Nederland

Tél: +31 (70) 358 6263 Fax: +31 (70) 358 4333 Email: [email protected]l

ResMed Finland Niittykatu 6 FIN 02200 Espoo Suomi

Puh: +358 9 8676820 Faksi: +358 9 86768222 Sähköposti: rece[email protected]

ResMed GmbH & Co. KG Fraunhoferstraße 16 82152 Martinsried Deutschland

Tel: +49 (0) 89 / 99 01 - 00 or +49 (0) 800 2 777 000 (gebührenfrei) Fax: +49 (0) 89 / 99 01 - 10 55

Email: [email protected]

ResMed Hong Kong Limited Room 1714, Miramar Tower 132-134 Nathan Road Tsim Sha Tsui Hong Kong

Tel: +852 2366 0707 Fax: +852 2366 4546 Email: [email protected]

ResMed Japan Nihonbashi Hisamatsu Bldg. 4F, 2-28-1 Nihonbashi-Hamacho, Chuo-Ku, Tokyo 103-0007, Japan

Tel: +81 (3) 3662 5056 Fax: +81 (3) 3662 5040

ResMed Malaysia Sdn Bhd Suite E-10-20, Plaza Mon’t Kiara No. 2 Jalan 1/70C Mon’t Kiara 50480 Kuala Lumpur

Malaysia Tel: +60 3 6201 7177 Fax: +60 3 6201 2177 Email: reception@resmed.com.my

ResMed NZ Ltd PO Box 51-048 Pakuranga Auckland New Zealand

Tel:+64 274 737 633 Fax:+64 9 239 0193 Email: [email protected]

ResMed SA Parc de la Bandonnière 2, rue Maurice Audibert 69800 Saint-Priest France

Tél: +33 (0) 4 37 251 251 Fax: +33 (0) 4 37 251 260 Email: reception@resmed.fr

ResMed Singapore Pte Ltd 238A Thomson Road # 12-03/04 Novena Square Tower A Singapore 307684

Tel: +65 6284 7177 Fax: +65 6284 7787 Email: [email protected]

ResMed Spain SL C/Arturo Soria, 245 28033 Madrid España

Tel: +34 (93) 5908154 Fax: +34 (93) 5908153 Email: [email protected]

ResMed Sweden AB Industrigatan 2 S-461 37 Trollhättan Sverige

Tel: +46 520 420 110 Fax: +46 520 397 15 Email: [email protected]

Labhardt AG Thannerstrasse 57 CH-4054 Basel Schweiz

Tel: +41 (061) 307 9711 Fax: +41 (061) 307 9722 Email: [email protected]

US DESIGNATED AGENT: ResMed Corp

EU AUTHORIZED REPRESENTATIVE: ResMed (UK) Ltd

www.myresmed.com

33887r2.book Page ii Thursday, June 30, 2005 1:36 PM

ENGLISH

1

USER’S MANUAL

English

S8 AutoSet Vantage

™

System

33887r2.book Page 1 Thursday, June 30, 2005 1:36 PM

2

33887r2.book Page 2 Thursday, June 30, 2005 1:36 PM

3

CONTENTS

ENGLISH

CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Y

OUR RESPONSIBILITY 5

MEDICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

A

BOUT THE S8 AUTOSET VANTAGE 5

C

ONTRAINDICATIONS 5

W

ARNINGS 6

C

AUTIONS 7

A

DVERSE EFFECTS 7

THE S8 AUTOSET VANTAGE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

S8 A

UTOSET VANTAGE 9

M

ASKS 9

H

UMIDIFIER 10

R

ESSCAN™ DATA CARD MODULE 10

A

CCESSORIES 10

HOW TO USE THE S8 AUTOSET VANTAGE . . . . . . . . . . . . . . . . . . . . . . . 11

S

ET UP THE S8 AUTOSET VANTAGE 11

A

SSEMBLE THE MASK 11

S

TART TREATMENT 12

S

TOPPING TREATMENT 13

U

SING THE MASK-FITTING FEATURE 13

HOW TO ATTACH A HUMIDIFIER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

A

TTACH A HUMIDAIRE 3I™ HUMIDIFIER 15

HOW TO USE THE KEYPAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

H

OW TO CHANGE THE SETTINGS 18

HOW TO USE THE STANDARD MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

HOW TO USE THE DETAILED MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

S

ETTINGS MENU 24

R

ESULTS MENU 25

O

PTIONS MENU 25

S

ERVICING MENU 25

M

ESSAGES ON THE S8 AUTOSET VANTAGE LCD 25

S8 MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

U

SING A BLANK MODULE 27

U

SING A RESSCAN DATA CARD MODULE 27

33887r2.book Page 3 Thursday, June 30, 2005 1:36 PM

4

CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

D

AILY CLEANING 31

W

EEKLY CLEANING 31

P

ERIODIC CLEANING 31

R

EPLACING THE AIR FILTER 32

S

ERVICING 32

FREQUENTLY ASKED QUESTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

S8 A

UTOSET VANTAGE (NO ACCESSORIES) 39

A

CCESSORIES 39

A

LL DEVICES (WHERE APPLICABLE) 40

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

33887r2.book Page 4 Thursday, June 30, 2005 1:36 PM

5

ENGLISH

INTRODUCTION

Thank you for choosing the S8 AUTOSET VANTAGE™ flow generator. The S8 AUTOSET

VANTAGE is a compact, all-in-one package with an inbuilt power supply and the option

of integrated data management and humidification.

This user manual contains the information you need for the correct use of your

S8 AUTOSET VANTAGE.

YOUR RESPONSIBILITY

The owner or user of this system shall have sole responsibility and liability for any injury

to persons or damage to property resulting from:

• operation which is not in accordance with the operating instructions supplied

• maintenance or modifications carried out unless in accordance with authorized

instructions and by authorized persons.

Please read this manual carefully before use.

This manual contains special terms and icons that appear in the margins to draw your

attention to specific and important information.

• Warning alerts you to possible injury.

• Caution explains special measures for the safe and effective use of the device.

• Note is an informative or helpful note.

MEDICAL INFORMATION

ABOUT THE S8 AUTOSET VANTAGE

The S8 AUTOSET VANTAGE self-adjusting sleep apnea system is indicated for the

treatment of obstructive sleep apnea (OSA) in adult patients. The

S8 AUTOSET

V

ANTAGE self-adjusting sleep apnea system has two treatment modes: AutoSet and

fixed-pressure CPAP.

The

S8 AUTOSET VANTAGE system is intended for home and hospital use.

!

CAUTION

In the US, Federal law restricts this device to sale by or on the order of a physician.

CONTRAINDICATIONS

The S8 AUTOSET VANTAGE is not a life support device and may stop operating during

power failure or certain fault conditions. It should not be used by patients who are

dependent on continuous therapy.

Positive airway pressure therapy may be contraindicated in some patients with the

following pre-existing conditions:

• severe bullous lung disease

33887r2.book Page 5 Thursday, June 30, 2005 1:36 PM

6

• pneumothorax

• pathologically low blood pressure

• dehydration

• cerebrospinal fluid leak, recent cranial surgery, or trauma.

WARNINGS

• The entire manual should be read before using the S8 AUTOSET VANTAGE.

• Advice contained in this manual should not supersede instructions given by the

prescribing physician.

• A patient should not connect a device to the data communication port unless

instructed to do so by their health care provider or physician. Only ResMed

products are designed to be connected to the data communication port.

Connecting other devices could result in injury, or damage to the

S8 AUTOSET

VANTAGE device.

• The S8 AUTOSET VANTAGE should only be used with masks (and connectors)

*

recommended by ResMed, or by a physician or respiratory therapist. A mask

should not be used unless the

S8 AUTOSET VANTAGE device is turned on and

operating properly. The vent hole or holes associated with the mask should never

be blocked.

Explanation: The

S8 AUTOSET VANTAGE is intended to be used with special

masks (or connectors)

*

which have vent holes to allow continuous flow of air out

of the mask.

When the device is turned on and functioning properly, new air from the device

flushes the exhaled air out through the mask vent holes. However, when the

device is not operating, insufficient fresh air will be provided through the mask, and

the exhaled air may be rebreathed. Rebreathing of exhaled air for longer than

several minutes can, in some circumstances, lead to suffocation. This applies to

most models of CPAP devices.

• In the event of power failure or machine malfunction, remove the mask.

• The S8 AUTOSET VANTAGE can be set to deliver pressures up to 20 cm H

2

O. In the

unlikely event of certain fault conditions, pressures up to 30 cm H

2

O are possible.

• If oxygen is used with this device, the oxygen flow must be turned off when the

device is not operating.

Explanation: When the CPAP device is not in operation and the oxygen flow is

left on, oxygen delivered into the air delivery tubing may accumulate within the

CPAP machine enclosure and create a risk of fire. This applies to most types of

CPAP machines.

• Oxygen supports combustion. Oxygen should not be used while you are

smoking or in the presence of an open flame.

* Ports may be incorporated into the mask or in connectors that are near the mask.

33887r2.book Page 6 Thursday, June 30, 2005 1:36 PM

7

ENGLISH

MEDICAL INFORMATION

• Always ensure airflow is being generated by the device before the oxygen

supply is turned on.

• Always turn the oxygen supply off before stopping the airflow from the device.

Note: At a fixed rate of supplemental oxygen flow, the inhaled oxygen concentration

will vary, depending on where the oxygen is introduced, the pressure settings, patient

breathing pattern, mask selection, and leak rate.

• Do not use the S8 AUTOSET VANTAGE if there are obvious external defects or

unexplained changes in performance.

• Do not open the S8 AUTOSET VANTAGE case. There are no user serviceable parts

inside. Repairs and internal servicing should only be performed by an authorized

service agent.

• Explosion hazard—do not use in the vicinity of flammable anesthetics.

CAUTIONS

• At low pressures, the flow through the exhalation ports of your mask may not

clear all exhaled gas from the tubing. Some rebreathing may occur.

• The airflow for breathing produced by this device can be as much as 11

o

F (6

o

C)

higher than the temperature of the room. Caution should be exercised if the room

temperature is warmer than 90

o

F (32

o

C).

• When AC mains power (100/240V AC) is not available, always use a ResMed

DC-12 converter. (The DC-12 converter is available as an optional accessory.)

• If supplied, the RESSCAN™ Data Card module is designed for use with specific

ResMed devices.

• Only use the RESSCAN Data Card module (if supplied) as specified in this manual.

Note: The above are general warnings and cautions. Specific warnings, cautions, and

notes appear with the relevant instructions in the manual.

ADVERSE EFFECTS

Patients should report unusual chest pain, severe headache, or increased

breathlessness to their prescribing physician. An acute upper respiratory tract infection

may require temporary discontinuation of treatment.

The following side effects may arise during the course of therapy with the S8 device:

• drying of the nose, mouth, or throat

• nosebleed

• bloating

• ear or sinus discomfort

• eye irritation

• skin rashes

• chest discomfort.

33887r2.book Page 7 Thursday, June 30, 2005 1:36 PM

8

33887r2.book Page 8 Thursday, June 30, 2005 1:36 PM

9

ENGLISH

THE S8 AUTOSET VANTAGE SYSTEM

The S8 AUTOSET VANTAGE device is part of a system that consists of five elements:

• S8 AUTOSET VANTAGE self-adjusting flow generator

• Mask

• Humidifier

• Data management products

• Accessories.

S8 AUTOSET VANTAGE

Please refer to the illustrations in section A of the illustration sheet.

FRONT VIEW (A-1)

Shows the keypad and LCD screen, and the air outlet.

REAR VIEW (A-2)

Shows where the module attaches, and the location of the air filter and power sockets.

POWER CORD (A-3)

Power cord to attach the S8 AUTOSET VANTAGE to the AC (mains) power.

CARRY BAG (A-4)

The S8 AUTOSET VANTAGE carry bag contains two pouches: one for storing the S8

device, the other for storing the integrated humidifier. When storing the humidifier,

always put it in the larger, mesh pouch.

AIR TUBING (A-5)

The 6‘6” (2 m) air tubing connects the

S8 AUTOSET VANTAGE to your mask.

MASKS

You will also need a ResMed mask system (supplied separately).

The ResMed mask systems that are recommended for use with the

S8 AUTOSET

V

ANTAGE are:

NASAL MASKS

•

MODULAR NASAL MASK

• MIRAGE VISTA™ NASAL MASK

• ULTRA MIRAGE™ NASAL MASK

• MIRAGE™ NASAL MASK

• MIRAGE ACTIVA™ NASAL MASK

• PAPILLON™.

N

ASAL PILLOWS SYSTEMS

•

MIRAGE SWIFT™ NASAL PILLOWS SYSTEM.

F

ULL FACE MASKS

•

MIRAGE™ FULL FACE MASK

• MIRAGE™ FULL FACE MASK SERIES 2

33887r2.book Page 9 Thursday, June 30, 2005 1:36 PM

10

• ULTRA MIRAGE™ FULL FACE MASK

• RESMED HOSPITAL FULL FACE MASK.

Note: Not all masks are available in all regions.

!

WARNING

In AutoSet mode, only ResMed mask systems are compatible for use with the

S8 AutoSet Vantage. Please refer to “Warnings” on page 6.

HUMIDIFIER

Please refer to the illustration in section B of the illustration sheet.

A humidifier may be required if you are experiencing dryness of the nose, throat, or

mouth. The

S8 AUTOSET VANTAGE is compatible for use with the HUMIDAIRE 3i

integrated heated humidifier (B-1).

RESSCAN

™

DATA CARD MODULE

The RESSCAN Data Card module and RESSCAN Data Card (C-1) may be used with the

S8 AUTOSET VANTAGE either to help your clinician to monitor your treatment or to

provide you with updates to your device settings. See “Using a ResScan Data Card

Module” on page 27 for information about how to use the Data Card module and

Data Card.

ACCESSORIES

Please refer to the illustrations in section C of the illustration sheet.

Other accessories for use with the

S8 AUTOSET VANTAGE:

• Front cap (not available in all regions) (C-2)

• Air tubing 9‘10” (3 m) (C-3)

• DC-12 converter (C-4)

• Blank module (C-5).

Note: ResMed regularly releases new products. Please check our website at

<www.myresmed.com>.

33887r2.book Page 10 Thursday, June 30, 2005 1:36 PM

11

ENGLISH

HOW TO USE THE S8 AUTOSET VANTAGE

Please refer to the illustrations in section D of the illustration sheet.

SET UP THE S8 AUTOSET VANTAGE

1 Place the S8 AUTOSET VANTAGE on a table near the head of your bed.

!

CAUTION

Be careful not to place the device where it can be bumped or where someone is

likely to trip over the power cord.

Note: You can also place your S8 AutoSet Vantage on the floor beside or underneath your

bed. Ensure that the area is free from dust and clear of bedding, clothes or any other

objects that could block the air inlet.

2 Connect the power cord to the socket at the rear of the flow generator (D-1). Plug

the other end of the power cord into the power outlet.

!

WARNING

Make sure the power cord and plug are in good condition and the equipment is not

damaged.

3 Connect one end of the air tubing firmly onto the air outlet (D-2).

!

WARNING

• Only ResMed air tubing should be used with your flow generator. A different

type of air tubing may alter the pressure you actually receive, reducing the

effectiveness of your treatment.

• Blocking the air inlet or tubing while in operation could lead to overheating of

the device.

• In the clinical environment any personal computer that is used with your CPAP

system must be at least 5’ (1.5 m) away from, or at least 8’ (2.5 m) above, the

patient. It must also comply with the relevant test standard. For personal

computers the international standard is IEC 60950 or equivalent.

ASSEMBLE THE MASK

1 Assemble your mask system according to the mask user instructions.

2 Connect your mask system to the free end of the air tubing (D-3).

3 Check that the mask setting on the MASK screen is the one recommended for the

mask you are using (see the table in “How to Select the Mask Type”).

The

S8 AUTOSET VANTAGE is now ready for use (D-4).

33887r2.book Page 11 Thursday, June 30, 2005 1:36 PM

12

START TREATMENT

1 Make sure the power is on.

A welcome message is displayed briefly on the LCD screen, then the standby screen

appears. In CPAP mode, the standby screen displays the word “RAMP”. In AutoSet

mode, the standby screen displays the word “SETTLING”.

The key and LCD backlights also turn on.

2 Lie down and arrange the air tubing so that it is free to move if you turn in your sleep.

!

CAUTION

• Do not leave long lengths of air tubing around the top of your bed. They could

twist around your head or neck while you are sleeping.

• Make sure the area around the flow generator is dry and clean. It should also be

clear of bedding, clothes, and other potential blockages.

3 Alter the ramp or settling time if required (see “How to Change the Ramp or Settling

Time” on page 19).

To start treatment, press the Start/Stop key, unless your clinician has set up your

device to start delivering therapy automatically. If so, your device will start when you

breathe into your mask (see “SmartStart” for details).

4 Fit your mask as described in the mask user instructions.

!

WARNING

A mask should not be used unless the S8 AUTOSET VANTAGE device is powered and

operating properly.

5 When ramping (or settling) begins, the LCD will display the word "RAMPING", (or

“SETTLING”) with the current pressure indicated as dashes. Each dash is

approximately equivalent to 2 cm H

2

O. For example, 6 dashes represents

approximately 12 cm H

2

O pressure.

SMARTSTART™

The S8 AUTOSET VANTAGE has a function called SmartStart™ that your clinician can

enable. If SmartStart is enabled, your device will start automatically when you breathe

into your mask, and will stop automatically when you take your mask off. This means

you do not have to press the Start/Stop key to begin or end treatment.

Note: Do not use SmartStart when using a mask with an anti-asphyxia valve, such as the

Mirage Full Face Mask.

33887r2.book Page 12 Thursday, June 30, 2005 1:36 PM

13

ENGLISH

HOW TO USE THE S8 AUTOSET VANTAGE

STOPPING TREATMENT

To stop treatment at any time, remove your mask and press the Start/Stop key

or

if your clinician has enabled SmartStart, simply remove your mask and treatment will

end.

USING THE MASK-FITTING FEATURE

You can use the S8 AUTOSET VANTAGE mask-fitting feature to help you fit your mask

properly. This feature delivers air pressure for a three-minute period, prior to starting

treatment, during which you can check and adjust your mask fit to minimize leaks.

Note: Make sure that the mask setting on the MASK screen is the same as the mask you

are using.

To use the mask-fitting feature:

1 Fit your mask as described in the mask user instructions.

2 Hold down the Start/Stop key for at least three seconds until air pressure delivery

starts.

The following display will appear on the LCD screen indicating that the mask-fitting

feature is operating. Your S8 device will ramp to the mask-fit pressure and will remain

at this pressure for three minutes.

The LCD also displays a mask-fit star rating. See “Definitions of Mask-Fit Star Rating”

on page 14.

Note: The mask-fit star rating display disappears after three minutes.

The mask-fitting feature can only be started from the RAMP or SETTLING screen.

In AutoSet mode, the mask-fit pressure is the highest pressure that you are likely to receive

based on the previous night’s session or 10 cm H

2

O, whichever is greater.

In CPAP mode, the mask-fit pressure is the set treatment pressure or 10 cm H

2

0,

whichever is greater.

3 Adjust your mask, mask cushion, and headgear until you have a secure and comfortable

fit.

Once you have a secure and comfortable fit, check your mask-fit star rating on the

LCD screen. Table 4 explains the mask-fit star ratings.

Note: If there is another person nearby to check your mask-fit star rating, you can adjust

your mask, mask cushion, and headgear while lying down.

MASK FIT:

*****

excelnt

mask-fit star rating

33887r2.book Page 13 Thursday, June 30, 2005 1:36 PM

14

4 After three minutes, the pressure reverts to the set pressure and treatment will begin.

• If you do not wish to wait three minutes, hold down the Start/Stop key for at

least three seconds to start treatment immediately.

• If you press the Start/Stop key for less than three seconds, the unit will return

to standby mode (the RAMP or SETTLING screen is displayed).

Table 1: Definitions of Mask-Fit Star Rating

Star rating Definition

***** Excellent

****- Very good

***-- Good

**--- Adjust mask

*---- Adjust mask

----- Adjust mask

33887r2.book Page 14 Thursday, June 30, 2005 1:36 PM

15

ENGLISH

HOW TO ATTACH A HUMIDIFIER

ATTACH A HUMIDAIRE 3

i

™

HUMIDIFIER

Please refer to the illustrations in section E of the illustration sheet, and your HumidAire 3i

manual.

The

HUMIDAIRE 3

i

attaches to the front of the S8 AUTOSET VANTAGE to provide heated

humidification. No other accessories are required for its use

.

Notes:

a. Make sure the water chamber of the HumidAire 3i is empty before you attach or

detach the humidifier.

b. Remove the connector plug on the S8 AutoSet Vantage before you attach the

HumidAire 3i. Reattach the connector plug firmly after you detach the humidifier.

STORING THE HUMIDAIRE 3

i

Store the HUMIDAIRE 3

i

in the larger, mesh-top pouch of the S8 AUTOSET VANTAGE

carry bag when not in use.

33887r2.book Page 15 Thursday, June 30, 2005 1:36 PM

La page charge ...

ResMed Humidifier s8 Manuel utilisateur

Ce manuel convient également à

ResMed Humidifier s8 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents