RIDGID RV2400A Manuel utilisateur

Wet/Dry Vacs

WET/DRY VAC PARTS

& ACCESSORIES

1-800-474-3443

Call Us 1

st

• Operation

• Warranty

(See back cover)

• Technical Assistance

• Repair Parts

For any questions about:

Please have your Model Number and

Serial Number on hand when calling.

RV24000, RV26000,

RV2400M0, RV2600M0

LARGE CAPACITY - 2-STAGE

HOUSEHOLD WET/DRY VACS

QUESTIONS OR COMMENTS? CONTACT US AT

www.RIDGIDvacs.com

In the U.S. and Canada, Call 1-800-4-RIDGID

In Mexico, Call 01-800-701-9811

Part No. SP6729 Printed in Mexico

OWNER’S MANUAL

SAVE THIS MANUAL FOR FUTURE REFERENCE

Thank you for buying a RIDGID product.

• Español - página 21

• Français - page 41

WARNING:

To reduce the risk of injury, the user must read and understand the owner’s manual

before using this product.

!

SP6729-5 RIDGID ESF 111418.indb 1 12/3/18 11:18 PM

2

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of using common

sense, staying alert, and knowing how your

Wet/Dry Vacuum Cleaner (“Vac”) works.

Safety Signal Words

DANGER: Indicates a hazardous

situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates

a hazardous situation which, if not

avoided, could result in death or serious

injury.

CAUTION: Indicates a hazardous

situation which, if not avoided, could

result in minor or moderate injury.

When using your Vac, always follow

basic safety precautions including the

following:

WARNING:

- To reduce the risk of fire,

electric shock, or injury:

• Read and understand this manual and

all labels on the Vac before operating.

• Use only as described in this manual.

• Do not leave Vac running while

unattended - you may fail to notice

important signs indicating abnormal

operation such as loss of suction,

debris/liquid exiting exhaust, or

abnormal motor noises. Immediately

stop using Vac if you notice these signs.

• Do not leave Vac when plugged in.

Unplug from outlet when not in use and

before servicing.

• Sparks inside the motor can ignite

flammable vapors or dust. To reduce

the risk of fire or explosion, do not use

near combustible liquids, gases, or

dusts, such as gasoline or other fuels,

lighter fluid, cleaners, oil-based paints,

natural gas, coal dust, magnesium

dust, grain dust, aluminum dust, or gun

powder.

• Do not vacuum anything that is burning

or smoking, such as cigarettes,

matches, or hot ashes.

• To avoid the risk of self-ignition of drum

debris, empty drum after each use.

Combustible materials, such as rags or

sawdust containing stain or urethane,

can be sources of such overheating.

• Do not vacuum drywall dust, cold

fireplace ash, or other fine dusts

with standard filter. These may pass

through the filter and be exhausted

back into the air. Use a fine dust filter

instead.

• To reduce the risk of inhaling toxic

vapors, do not vacuum or use near

toxic or hazardous materials.

• To reduce the risk of electric shock,

do not expose to rain or allow liquid

to enter motor compartment.

Store indoors.

• This Wet/Dry Vac is not intended for

use by persons (including children) with

reduced physical, sensory, or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

!

Table of Contents

Section Page

Table of Contents......................2

Important Safety Instructions . . . . . . . . . . . . . 2

Safety Signal Words ..................2

Grounding Instructions ..................4

Introduction...........................5

Unpacking and Checking ................5

Drum/Caddy Assembly..................8

Wet/Dry Vac Assembly.................11

Section Page

Operation ...........................12

Vacuuming Dry Materials .............13

Vacuuming Liquids ..................13

Emptying the Drum ..................14

Moving the Wet/Dry Vac ..............14

Blowing Feature ....................15

Accessory Storage ....................16

Cord Wrap.........................16

Hose Storage ......................16

Maintenance.........................17

Warranty............................20

!

SP6729-5 RIDGID ESF 111418.indb 2 12/3/18 11:18 PM

3

• Do not use with a torn filter or without

the filter installed except when

vacuuming liquids as described in this

manual. Dry debris ingested by the

impeller may damage the motor or be

exhausted into the air.

• Turn off Vac before unplugging.

• To reduce the risk of injury from

accidental starting, unplug power cord

before changing or cleaning filter.

• Do not unplug by pulling on cord.

To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or

other parts. If your Vac is not working

as it should, has missing parts, has

been dropped, damaged, left outdoors,

or dropped into water, call customer

service.

• Do not pull or carry by cord, use cord

as handle, close a door on cord, or pull

cord around sharp edges or corners.

Do not run Vac over cord. Keep cord

away from heated surfaces.

• Do not handle plug, switch, or the Vac

with wet hands.

• Use only extension cords that are rated

for outdoor use and have a grounding

conductor. Extension cords in poor

condition or too small in wire size can

pose fire and shock hazards. To reduce

the risk of these hazards, be sure the

cord is in good condition and that liquid

does not contact the connection.

Do not use an extension cord with

conductors smaller than 1,3 mm

2

(16 AWG).

- Connect only to a properly-grounded

outlet. See grounding instructions.

• Do not put any object into ventilation

openings. Do not vacuum with any

ventilation openings blocked; keep free

of dust, lint, hair or anything that may

reduce air flow.

• Keep hair, loose clothing, fingers, and

all parts of body away from openings

and moving parts.

• To reduce the risk of falls, use extra

care when cleaning on stairs.

• To reduce the risk of back injury or

falls, do not lift a Vac that is heavy with

liquid or debris. Partially empty the Vac

by scooping debris or draining liquid to

make it comfortable to lift.

• To reduce the risk of personal injury

or damage to Vac, use only RIDGID

recommended accessories.

• When using as a blower:

- Direct air discharge only at work area.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except

blowing dirt and debris.

- Do not use as a sprayer.

• To reduce the risk of eye injury, wear

safety eyewear. The operation of

any utility Vac or blower can result in

foreign objects being blown into the

eyes, which can result in severe eye

damage.

• To reduce the risk of being struck by,

or pulled down by, a rolling Vac, block

the wheels when using on any uneven

or sloped surface.

CAUTION:

• To reduce the risk of hearing damage,

wear ear protectors when using for

extended time or in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the

relative humidity of the air is low.

Vacuuming fine debris with your Vac

can deposit static charge on the hose

or Vac. To reduce the frequency of

static shocks in your home or when

using this Vac, add moisture to the air

with a humidifier.

!

Observe the following warnings that

appear on the motor housing of your Vac:

WARNING:

To reduce the risk of electric shock

- do not expose to rain - store

indoors.

SAVE THIS MANUAL

WARNING:

• For your own safety, read and

understand owner’s manual.

• Do not run unattended.

• Do not pick up hot ashes,

coals, toxic, flammable or other

hazardous materials.

• Do not use around explosive

liquids or vapors.

!

SP6729-5 RIDGID ESF 111418.indb 3 12/3/18 11:18 PM

4

Grounding Instructions

This Vac must be grounded.

If it should malfunction or break

down, ground ing provides a path of

least resistance for electric current to

reduce the risk of electric shock. This

Vac is equipped with a cord having

an equipment-grounding conductor

and grounding plug. The plug must be

inserted into an appropriate outlet that

is properly installed and grounded in

accordance with all local codes and

ordinances.

WARNING:

Improper connection of the

equipment grounding conductor

can result in a risk of electric shock.

Check with a qualified electrician or

service person if you are in doubt

as to whether the outlet is properly

grounded. Do not modify the plug

provided with the appliance - if it

will not fit the outlet, have a proper

outlet installed by a qualified

electrician.

This vac is for use on a nominal 120-volt

circuit, and has a grounded plug that

looks like the plug shown. A temporary

adapter that looks like the adapter shown

may be used to connect this plug to a

2-pole receptacle, as shown. If a properly

grounded outlet is not available, the

temporary adapter should only be used

until a properly grounded outlet can be

installed by a qualified electrician.

Properly

Grounded

Outlet

Grounding

Prong

3-Prong

Plug

Make sure this is a

metal screw connected

to a known ground

Green

Grounding Lug

2-Prong Outlet

3-Prong Plug

Adapter

The green-colored rigid ear, lug, or the

like, extending from the adapter, must be

connected to a permanent ground such

as a properly grounded outlet box cover.

Whenever the adapter is used, it must be

held in place by a metal screw.

NOTE: In Canada, the use of a temporary

adaptor is not permitted by the Canadian

Electrical Code.

!

SP6729-5 RIDGID ESF 111418.indb 4 12/3/18 11:18 PM

5

Introduction

This Vac is rated for household use.

This Wet/Dry Vac is supplied with a

three-layer fine dust filter. It can be used

not only to pick up material like sawdust

Refer to the assembly sketch for

positioning of parts.

Remove contents of carton. Check each

item against the Carton Contents List.

Call 1-800-4-RIDGID (1-800-474-3443) from

the US and Canada, 01-800-701-9811 from

Mexico, or E-mail us at info@RIDGID.com

if any parts are damaged or missing.

Unpacking and Checking Carton Contents

and gravel but also ultra fine material

like drywall dust and cold fireplace ash.

These types of materials are so small

they would pass through traditional filters.

Carton Contents List

Key Description Qty

A Wet/Dry Vac Assembly ..................1

B Professional Locking Hose.............1

C Muffler/Diffuser ...............................1

D Owner’s Manual .............................1

A

B

D

C

Phillips

Screwdriver

Tools Required

MalletHammer

5/8”

Socket

Recommended

5/8"

SP6729-5 RIDGID ESF 111418.indb 5 12/3/18 11:18 PM

6

Carton Contents List

Key Description Qty

Carton containing the following parts:

E Tool Holder ..................................1

F Wheels .........................................2

G Metal Handle ................................ 1

H Axle ..............................................1

I* Caddy, Right ................................1

J* Caddy, Left ..................................1

* These items may come preassembled.

If they are not present in the carton

check the Wet/Dry Vac assembly to

see if they are preassembled.

Carton Contents List

Key Description Qty

Bag of Loose Parts -

Containing the following:

K Casters ............................................2

L Cap Nuts .........................................2

M Wheel Caps ....................................2

N Screws, Type AB #10 x 1-3/4” (44 mm) ... 4

K

L

M

N

Unpacking and Checking Carton Contents (cont.)

H

E

J*

I*

F

G

SP6729-5 RIDGID ESF 111418.indb 6 12/3/18 11:18 PM

7

2-1/2” (64 mm) Accessories For

Stock Number RV2400A or

RV2400M

Carton Contents List

Key Description Qty

A Floor Brush ..................................1

B Wet Nozzle ..................................1

C Crevice Tool .................................1

D Utility Nozzle ................................1

E Extension Wands ......................... 2

A

B

C

D

E

Unpacking and Checking Carton Contents (cont.)

1-7/8” (46 mm) Accessories

For Stock Number RV2600B or

RV2600M

Carton Contents List

Key Description Qty

A Multi-Nozzle Body ........................ 1

B Floor Brush Insert ........................1

C Squeegee Insert ..........................1

D Carpet Insert ................................1

E Extension Wands ......................... 2

F Claw Nozzle ................................. 1

G Crevice Tool .................................1

H Dusting Brush ..............................1

A

B

C

D

F

E

G

H

SP6729-5 RIDGID ESF 111418.indb 7 12/3/18 11:18 PM

8

If any parts are missing or damaged

contact Customer Service.

Do not assemble until you have all the

parts.

1. Remove Left and Right Caddies from

Drum.

*TIP - Use a 5/8” (16mm) Socket to hold

the Cap Nut in a stable position when

hammering.

2. Install Cap Nut on one side of Shaft

Rod. Tap gently with Rubber Mallet

or Hammer until fully seated. Slide

open end of Shaft through the

Wheel (smooth side of wheel facing

outward).

3. Place Wheel/Shaft Assembly through

Caddy Left and on through the Caddy

Right, as shown.

4. Then place the remaining Wheel onto

the Caddy Assembly (smooth side

of wheel facing outward), and install

second Cap Nut.

5. Invert Drum to install Caddy. Place

the Caddy Assembly onto the Drum,

as shown. Be sure that Wheels

spin freely, and do not contact the

Caddies.

6. Once the Caddies are aligned on

the Drum, gently tap each end of

each Caddy until firmly seated. It

is recommended to tap the center

portion of the Front Caddies, as

shown.

7. Using a Rubber Mallet or Hammer,

gently tap the Wheel Caps onto each

Wheel until the Wheel Caps are firmly

seated onto each Wheel. This is

required on both sides.

Drum/Caddy Assembly

NOTE: Smooth side of the

wheel to the outside.

CADDY

ASSEMBLY

Cap

Nut

Shaft

Rod

Caddy Left

Wheel

Cap

Nut

Caddy

Right

5/8"

Socket

Wheel Cap

Mallet

Caddy

Wheel

1/16" (16 mm)

Clearance

TAP

1/16” (1.6 mm)

Clearance

SP6729-5 RIDGID ESF 111418.indb 8 12/3/18 11:18 PM

9

8. Insert the Caster Stem into the

Socket of the Caster Foot, as shown.

(Front casters only).

9. Push on the Caster until the Ball on

the Caster Stem is inserted all the

way into the Socket. You will be able

to hear the Ball snap into the Socket

and the Caster will swivel easily when

positioning is correct.

10. Install 4 Screws (supplied) into

matching holes on both right and left

side of Caddy, securing the Caddies

to the bottom of the Drum. Tighten

Screws until just snug. Do not over

tighten the Screws, as this may

deform the Caddies.

Installing Metal Handle

Press and hold Release Buttons while

installing Metal Handle into Handle

Receptacles on the Drum

(See illustration).

NOTE: An audible snap of Release

Buttons indicates successful engagement

of Metal Handle.

Removing Metal Handle

Press and hold Release Buttons, as

shown. While firmly pushing in Release

Buttons, pull the Metal Handle upwards

to remove (see illustration).

Socket

Caster Stem

Caster Ball

Caster (2)

Screws (4)

Drum/Caddy Assembly (cont.)

SP6729-5 RIDGID ESF 111418.indb 9 12/3/18 11:18 PM

Wall

Grommet

Wall Mount

Hook

(Not Included

with All Models)

Tote Snaps

Tote

Straps (4)

Handle

Extension

Wand

Storage

Locations

(Not Included

On All Models)

Installing Tool Holder

1. Position the Tool Holder to the Metal

Handle with Extension Wand Holders

(not included on all models) facing

the unit. Install the Tool Holder

by wrapping the Four Tote Straps

around the Metal Handle and Snap

each Strap in place, as shown.

2. As an alternative storage solution,

the Tool Holder may hang on a wall.

Two wall mounting hooks (not

included with all models) must be

secured to the wall, as shown

(sold separately).

Drum/Caddy Assembly (cont.)

10

SP6729-5 RIDGID ESF 111418.indb 10 12/3/18 11:18 PM

Wet/Dry Vac Assembly

1. Position the Powerhead Assembly on

the Drum/Caddy Assembly, as shown

(assembled earlier).

2. Rotate both Latches down and press

until you hear them snap over the

Flanges on the Drum.

Drum

Latch

Drum

Latch

Drum

Flange

Latch

Drum

Powerhead

Assembly

Insert Hose

Insert the Push Button end of the

Professional Locking Hose into the Vac

Inlet. The Professional Locking Hose

should snap into place.

To remove the Professional Locking Hose

from the Vac, press the Hose Assembly

Release Button and pull the Professional

Locking Hose out of the Vac Inlet,

as shown.

Press the Curved Metal Extension Wand

into the Coupling Ring of the Professional

Locking Hose End.

Join the two Metal Extension Wands,

aligning the Button and Hole so they

snap together.

Attach the Accessories, aligning the

Button and Hole so they snap together.

Release

Button

Press

and

Pull

Coupling

Ring

Accessory

Metal

Extension

Wand

(Curved)

Metal Extension

Wand (Straight)

Wet/Dry Vac &

Hose Assembly

11

Metal Wand

Button

Accessory

Hole

SP6729-5 RIDGID ESF 111418.indb 11 12/3/18 11:18 PM

Operation

=

OFF

=

ON

12

WARNING:

To reduce the risk of fire, explosion, or damage to Vac:

• Do not leave Vac running while unattended - you may fail to notice

important signs indicating abnormal operation such as loss of suction,

debris/liquid exiting the exhaust, or abnormal motor noises. Immediately

stop using Vac if you notice these signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off suction.

• Sparks inside the motor can ignite airborne flammables. Do not operate

Vac near flammable liquids or in areas with flammable gases, vapors, or

explosive/airborne dust. Flammable liquids, gases, and vapors include:

lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol,

and aerosol sprays. Explosive dusts include: coal, magnesium, aluminum,

grain, and gun powder.

• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.

• Do not leave sawdust or rags with stain or polyurethane residue inside Vac.

Empty drum after picking up these potentially self-heating materials.

WARNING: To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter motor compartment.

Store indoors.

• Do not handle plug, switch, or Vac with wet hands.

• Unplug Vac before servicing. If your Vac is not working as it should, has

missing parts, has been dropped, damaged, left outdoors, or dropped into

water, return it to an authorized service center or call customer service.

• When using an extension cord, use only outdoor-rated cords that are in

good condition. Do not allow the connection to come into contact with

liquid.

CAUTION: To reduce the risk of hearing damage, wear ear protectors when

using the Vac/Blower for extended time or in a noisy area.

!

After you plug the Power Cord into the

Outlet, turn the Unit on by pushing the

Switch from position “O” to position “l”.

The symbols used on the Switch Actuator

are International “On & Off” symbols.

“O” is the symbol for “OFF” and

“l” is the symbol for “ON”.

ON/OFF

Switch

!

SP6729-5 RIDGID ESF 111418.indb 12 12/3/18 11:18 PM

13

Operation (cont.)

Familiarize yourself with the Accessories

included with the Vac. Each Accessory

may be used in various ways for

vacuuming and blowing debris.

Here is a list of possible Accessories and

their uses.

Multi-Nozzle Body - Holds floor inserts

for specialized cleaning applications:

Floor Brush, Squeegee, and Carpet

Inserts. To change inserts, slide red tabs

to the “open” position and pull insert from

the center. Install new insert flush with

nozzle body and slide tabs to the “lock”

position.

Floor Brush Insert - Used for large area

clean-ups on smooth surfaces.

Squeegee Insert - Used for wet pickup

on smooth surfaces to pick up liquid and

dry the surface in one stroke.

Carpet Insert - Dry and wet pickup

nozzle for most upholstery and carpet

cleaning.

Claw Nozzle - Used to pick up debris in

hard to reach locations.

Dusting Brush - Used for detailed

cleaning in small spaces.

Crevice Tool - Used to pick up debris in

hard to reach locations.

Muffler/Diffuser - Used to disperse the

exhaust air stream while reducing noise.

Insert into the blowing port.

Extension Wands - These wands can

be connected together and provides

additional length for more reach.

Hose - Provides transfer of vacuum or

blowing capability to work site. Provides

the means of attaching extension wands

and nozzles.

Utility Nozzle - General purpose nozzle

for most vacuuming applications.

Wet Nozzle - Used for wet pickup on

smooth surfaces to pick up liquid and dry

the surface in one stroke.

Floor Brush - Used for large area clean-

ups on smooth surfaces.

WARNING:

Do not operate without filter cage

and float, as they prevent liquid

from entering the impeller and

damaging the motor.

Vacuuming Liquids

IMPORTANT:

1. When picking up small amounts of

liquid (2-4 inches (5-10 cm) of liquid

in the bottom of the Drum) the Filter

may be left in place.

2. When picking up larger amounts of

liquid (more than 4 inches (10 cm)

of liquid in the bottom of the Drum)

we recommend that the Filter be

removed. If the Filter is not removed,

it will become saturated and misting

may appear in the exhaust.

Vacuuming Dry Materials

1. The Filter must always be in correct

position to reduce the risk of leaks

and possible damage to Vac.

2. Your Wet/Dry Vac comes with the

VF5000 Filter installed. When using

your Vac to pick up very fine dust,

it will be necessary for you to empty

the Drum and clean the Filter at more

frequent intervals to maintain peak

Vac performance.

NOTE: A dry Filter is necessary to pick

up dry material. If you use your Vac to

pick up dust when the Filter is wet, the

Filter will clog quickly and be very difficult

to clean.

!

SP6729-5 RIDGID ESF 111418.indb 13 12/3/18 11:18 PM

14

3. After using the Vac to pick up liquids,

the Filter must be dried to reduce the

risk of possible mildew and damage

to the Filter.

4. When the liquid in the Drum reaches

a predetermined level, the Float

mechanism will rise automatically to

cut off air-flow. When this happens,

turn off the Vac, unplug the Power

Cord, and empty the Drum. You will

know that the Float has risen because

Vac airflow ceases and the motor

noise will become higher in pitch, due

to increased motor speed.

IMPORTANT: To reduce the risk of

damage to the Vac, do not run Motor

with Float in raised position.

Operation (cont.)

1. The Vac comes equipped with a

Drain for easy emptying of liquids.

Simply unscrew the Drain Cap and lift

the opposite side slightly to empty the

Drum.

2. Another option is to remove the

Powerhead Assembly.

3. Lay Powerhead Assembly aside on

a clean area while emptying Drum.

4. Dump the Drum contents into the

proper waste disposal container.

Emptying the Drum

Moving the Wet/Dry Vac

Should it become necessary to pick the

Vac up to move it, the Carry Handles

on each side of the Dust Drum are used

to lift.

To maneuver the Vac, the Metal Handle

in the rear of the unit should be used.

Drain

Cap

Drum

Powerhead

Assembly

Metal

Handle

Carry

Handles (2

)

Dust

Drum

WARNING:

To reduce the risk of injury from

accidental starting, unplug power

cord before emptying the drum.

!

WARNING:

To reduce the risk of back injury or

falls, do not lift a Vac heavy with

liquid or debris. Scoop or drain

enough contents out to make the

Vac light enough to lift comfortably.

!

SP6729-5 RIDGID ESF 111418.indb 14 12/3/18 11:18 PM

15

Operation (cont.)

Blowing Feature

Your Vac features a Blowing Port.

It can blow sawdust and other debris.

Follow the steps below to use your Vac

as a Blower.

1. Locate Blowing Port of your Vac.

2. Insert the Locking End of the

Professional Locking Hose into the

Vac Blowing Port. The Professional

Locking Hose should snap into place.

To remove the Professional Locking

Hose from the Vac, press the Release

Button in the Hose Assembly and pull

the Hose out of the Vac Blowing Port.

3. (Optional) Attach Extension Wand to

opposite end of Professional Locking

Hose.

4. Turn Vac on and you are ready to use

your Vac as a Blower.

CAUTION: Wear a dust mask if

blowing creates dust which might

be inhaled.

CAUTION: To reduce the risk of

hearing damage, wear ear protectors

when using the Vac/Blower for

extended time or in a noisy area.

!

Professional

Locking Hose

Blowing

Port

WARNING:

Always wear safety eyewear

complying with ANSI Z87.1 (or in

Canada, CSA Z94.3) before using as

a blower.

!

WARNING:

To reduce the risk of injury to

bystanders, keep them clear of

blowing debris.

!

SP6729-5 RIDGID ESF 111418.indb 15 12/3/18 11:18 PM

16

Push/Pull Handle

Cord Wrap

Power

Cord

Accessory Storage

Your Accessories may be stored in the

Tool Holder or in the two locations on

the Caddy Right/Left.

NOTE: Insert male end of extension

wand into the holder sleeve (not included

on all models) as shown.

Hose Storage

Area

Hose Storage

The Professional Locking Hose may be

stored by wrapping it around the Unit

and plugging the open end into one

of the storage locations on the Caddy

Assembly.

Extension

Wand

Storage

Extension

Wand

Accessory Storage Compartment

(Not Included

On All Models)

CAUTION: Do not operate

vacuum while the hose is still

wrapped around the powerhead

assembly in the storage position.

!

Cord Wrap

When vacuuming is complete, unplug

the Cord and wrap it around the

Powerhead Assembly. Secure the Cord

using the Cord Clip on the Plug.

The Power Cord should wrap under the

Push/Pull Handle (above the Inlet) and

around and under the Cord Wrap of the

Motor Cover.

WARNING:

Do not put any object into

ventilation openings. Do not

vacuum with any ventilation

openings blocked; keep free of

dust, lint, hair or anything that may

reduce air flow.

!

SP6729-5 RIDGID ESF 111418.indb 16 12/3/18 11:18 PM

17

Filter Installation:

1. Carefully slide the Qwik Lock™ Filter

over the Filter cage and press down

on the outside edge of the Filter until

the Rubber Gasket on the bottom

of the Filter seats securely around the

base of the Filter Cage and against

the Powerhead Assembly.

2. Align the small Center Hole in the top

of the Filter over the Qwik Lock™

Stud on the Filter Cage. Press firmly

on top of the Filter near the Stud to

allow the Filter to snap over the Ball

on the end of the Stud. The Filter is

now attached.

Filter Cage

Qwik Lock™

Stud

Powerhead

Assembly

Rubber

Gasket at

Bottom of

Filter

PUSH

DOWN

PULL

UP

Filter

Tabs (2)

Integrated Filter Plate

with Center Hole

PULL

UP

NOTE: Failure to properly seat the

bottom Gasket could result in debris

bypassing the Filter.

Removal and Installation of the

Qwik Lock™ Filter

Filter Removal:

1. Hold the Filter Tabs of the Qwik

Lock™ Filter in each hand.

2. With one thumb on the Qwik Lock™

Stud, which protrudes through the

integrated Filter Plate, lift up on the

Filter Tabs while pushing down on the

Stud.

3. This action will cause the Filter to

release from the Filter Cage.

Slide Filter off Cage.

IMPORTANT: To avoid damage to the

Blower Wheel and Motor, always reinstall

the Filter before using the Vac for dry

material pickup.

Maintenance

The Wet/Dry Vacs are supplied with

RIDGID’s Three-Layer Qwik Lock™

Filter. Replacement Three-Layer Qwik

Lock™ Filters are available where you

purchased your Vac. Ask for the RIDGID

Three-Layer Qwik Lock™ Filter VF5000.

NOTE: The Filter is made of high

quality paper designed to stop very small

particles of dust. The Filter can be used

for wet or dry pick up. Handle the Filter

carefully when removing to clean or

installing it. Creases in the Filter pleats

may occur from installation but not affect

the performance of the Filter.

Filter

WARNING:

To reduce the risk of injury from

accidental starting, unplug power

cord before changing or cleaning

filter.

!

WARNING:

Do not operate without filter cage

and float, as they prevent liquid

from entering the impeller and

damaging the motor.

!

SP6729-5 RIDGID ESF 111418.indb 17 12/3/18 11:18 PM

18

Maintenance (cont.)

Filter Cleaning

Your Filter should be cleaned often to

maintain peak Vac performance.

Cleaning A Dry Filter

1. Some removal of dry debris can be

accomplished without removing the

Filter from the Vac. Slap your hand

on top of the Powerhead Assembly

while the Vac is turned off.

2. For best cleaning results due to

accumulated dust, clean the Filter in

an open area. Cleaning SHOULD be

done outdoors and not in the living

quarters.

3. After Filter removal from Vac, remove

the dry debris by gently tapping Filter

against the inside wall of your Dust

Drum. The debris will loosen and fall.

4. For thorough cleaning of dry Filter

with fine dust (no debris), run water

through it as described under

“Cleaning A Wet Filter”.

Cleaning A Wet Filter

After Filter is removed, run water through

the Filter from a hose or spigot. Take

care that water pressure from the hose is

not strong enough to damage Filter.

IMPORTANT: After cleaning, check the

Filter for tears or small holes. Do not use

a Filter with holes or tears in it. Even

a small hole can cause a lot of dust to

come out of your Vac. If your Filter is

damaged or worn, replace it immediately.

Allow the Filter to dry before reinstalling

and storing the Vac or picking up dry

debris.

Cleaning and Disinfecting the

Wet/Dry Vac

To keep your Wet/Dry Vac looking its

best, clean the outside with a cloth

dampened with warm water and mild

soap.

To clean the Drum:

1. Dump debris out.

2. Wash Drum thoroughly with warm

water and mild soap.

3. Wipe out with dry cloth.

Before prolonged storage or as needed

(i.e., waste water pick up) the Drum

should be disinfected.

To disinfect the drum:

1. Pour 1 gallon (4 L) of water and

1 teaspoon (5 mL) chlorine bleach

into the Drum.

2. Let solution stand for 20 minutes,

carefully swishing every few minutes,

making sure to wet all inside surfaces

of the Drum.

3. Empty Drum after 20 minutes. Rinse

with water until bleach smell is gone.

Allow Drum to dry completely before

sealing the Motor on the Drum.

SP6729-5 RIDGID ESF 111418.indb 18 12/3/18 11:18 PM

19

Cord Maintenance

When vacuuming is complete, unplug

the Power Cord and wrap it around the

Powerhead Assembly. If the Power Cord

is damaged, it must be replaced by the

manufacturer or their service agent or by

similarly qualified personnel to reduce the

risk of accident.

Storage

Before storing your Vac, the Drum

should be emptied and cleaned. The

Power Cord should be wrapped around

the Powerhead Assembly and the Hose

should be stored as described in this

manual. Accessories should be kept in

the same area as the Vac so they can

be readily available. The Vac should be

stored indoors.

Maintenance (cont.)

Casters and Wheels

Should your Cart squeak or become

hard to roll, you should place two or

three drops of general purpose oil on

each Wheel at the Axle. If your Casters

are noisy, you may put a drop of oil on

the Roller Shaft to make them quieter.

Frame and Handles

Your Metal Handle is painted to prevent

rust, however, liquids and corrosive

debris should be wiped off with a soft

cloth should they come in contact with

the Handle.

Large Capacity — 2-Stage

Household Wet/Dry Vac

Model Numbers RV24000, RV26000,

RV2400M0 & RV2600M0

Electrical Ratings:

120 V~ 11.5 A 60 Hz

RIDGID parts are available on-line at

store.ridgid.com/provacs

Always order by Part Number - Not by Key Number

WARNING:

To assure product SAFETY and

RELIABILITY, any other maintenance,

repairs and adjustments should be

performed by Authorized Service

Centers, always using RIDGID

replacement parts.

!

WARNING:

To reduce the risk of injury from electrical shock, unplug power cord before

servicing the electrical parts of the Wet/Dry Vac.

!

WARNING:

All disassembly and repairs should be performed by qualified personnel.

!

SP6729-5 RIDGID ESF 111418.indb 19 12/3/18 11:18 PM

Part No. SP6729 Form No. SP6729-5 Printed in Mexico 11/18

• What is covered

RIDGID

®

Wet/Dry Vacs are warranted to be free of defects in workmanship and material.

• How long coverage lasts

This warranty lasts for the lifetime of the RIDGID

®

Wet/Dry Vac.

• How to obtain service

To obtain the benefit of this warranty, deliver via prepaid transportation the complete product to

RIDGE TOOL COMPANY, Elyria, Ohio, or any authorized RIDGID® INDEPENDENT SERVICE

CENTER. Pipe wrenches and other hand tools should be returned to the place of purchase.

• What we will do to correct problems

Warranted Wet/Dry Vacs will be repaired or replaced, at Ridge Tool Company’s option, and

returned at no charge; or, if after three attempts to repair or replace during the warranty period the

Wet/Dry Vac is still defective, you can elect to receive a full refund of your purchase price.

• What is not covered

Failures due to misuse, abuse or normal wear and tear are not covered by this warranty.

RIDGE TOOL COMPANY SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

• How local laws relate to the warranty

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you. This warranty gives you specific rights, and

you may also have other rights which vary from state to state, province to province, or country to

country.

• No other express warranty applies

This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID

®

Wet/Dry Vacs.

No employee, agent, dealer, or other person is authorized to alter this warranty or make any other

warranty on behalf of Ridge Tool Company.

Please have your Model Number and Serial Number on hand when calling.

c 2018 Emerson

QUESTIONS OR COMMENTS? CONTACT US AT

ridgid.com/warranty

In the U.S. and Canada, Call 1-800-4-RIDGID

In Mexico, Call 01-800-701-9811

www.RIDGID.com

Symbol of Quality, Durability and Dependability

This Warranty is Valid for the U.S. and Canada Only.

For Mexican Warranty Information Please See Enclosed Insert Sheet.

Stock No. RV2400A or RV2600B, RV2600M & RV2600M, RV2400M0 & RV2600M0

Model No. RV24000 or RV26000

Serial Number

Model and serial number may be found near the blowing port.

You should record both model and serial numbers in a safe place for future use.

SP6729-5 RIDGID ESF 111418.indb 20 12/3/18 11:18 PM

La page est en cours de chargement...

RIDGID RV2400A Manuel utilisateur

Ce manuel convient également à

RIDGID RV2400A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents