Schumacher Electric CBC 7700 Manuel utilisateur

Instruction Manual

Professional Fast Chargers

and Starters

CBC 7600 and CBC 7700

• English ...................................p. 1

• Français .................................p. 15

• Español ..................................p. 33

00-99-000701/1006

IMPORTANT SAFETY INSTRUCTIONS

Read and save this instruction manual. Keep it with the charger at all times.

CAUTION: The charger must be fully assembled before operating. Refer to “Assembly

Instructions,” page 6 for instructions.

1. SAVE THESE INSTRUCTIONS—This manual contains important safety and operating

instructions for battery charger models CBC 7600 and CBC 7700.

2. Use of an attachment not recommended or sold by the battery charger manufacturer may

result in a risk of re, electric shock, or injury to persons.

3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

4. An extension cord should not be used unless absolutely necessary. Use of improper extension

cord could result in a risk re and electric shock. If extension cord must be used, make sure:

a) That pins on plug of extension cord are the same number, size, and shape as those of plug

on charger;

b) That extension cord is properly wired and in good electrical condition; and

c) That wire size is large enough for AC ampere rating of charger as specied in the

following table:

5. Do not operate charger with damaged cord or plug. Replace the cord or plug immediately.

6. WARNING: Handling the cord on this product or cords associated with accessories sold

with this product, may expose you to lead, a chemical known to the State of California to

cause cancer and birth defects or other reproductive harm. Wash hands after handling.

7. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged

in any way. Take it to a qualied serviceman.

1

8. Do not disassemble charger. Take it to a qualied serviceman when service or repair is

required. Incorrect reassembly may result in a risk of electric shock or re.

9. To reduce risk of electric shock, unplug charger from outlet before attempting any

maintenance or cleaning. Turning off controls will not reduce this risk.

WARNING: RISK OF EXPLOSIVE GASES

1. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES

GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR

THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING

YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS

EXACTLY.

2. To reduce risk of battery explosion, follow these instructions and those published by battery

manufacturer and manufacturer of any equipment you intend to use in vicinity of battery.

Review cautionary markings on these products and on engine.

PERSONAL PRECAUTIONS

1. Someone should be within range of your voice or close enough to come to your aid when you

work near a lead-acid battery.

2. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or

eyes.

3. Wear complete eye protection and clothing protection. Avoid touching eyes while working

near battery.

4. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters

eye, immediately ood eye with running cold water for at least 10 minutes and get medical

attention immediately.

5. NEVER smoke or allow a spark or ame in vicinity of battery or engine.

6. Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-

circuit battery or other electrical part that may cause explosion.

7. Remove personal metal items, such as rings, bracelets, necklaces, and watches, when

working with a lead-acid battery. A lead-acid battery can produce a short-circuit current high

enough to weld a ring or the like to metal, causing a severe burn.

8. Use charger for charging a LEAD-ACID battery only. It is not intended to supply power to

a low voltage electrical system other than in a starter-motor application. Do not use battery

charger for charging dry-cell batteries that are commonly used with home appliances. These

batteries may burst and cause injury to persons and damage to property.

9. NEVER charge a frozen battery.

2

PREPARING TO CHARGE

1. If necessary to remove battery from vehicle to charge, always remove grounded terminal

from battery rst. Make sure all accessories in the vehicle are off, so as not to cause an arc.

2. Be sure area around battery is well ventilated while battery is being charged. Gas can be

forcefully blown away by using a piece of cardboard or other nonmetallic material as a fan.

3. Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.

4. Add distilled water in each cell until battery acid reaches level specied by battery

manufacturer. This helps purge excessive gas from cells. Do not overll. For a battery

without cell caps, carefully follow manufacturer’s recharging instructions.

5. Study all battery manufacturer’s specic precautions, such as removing or not removing cell

caps while charging and recommended rates of charge.

6. Determine voltage of battery by referring to car owner’s manual and make sure that output

voltage selector switch is set at correct voltage. If charger has adjustable charge rate, charge

battery initially at lowest rate.

CHARGER LOCATION

1. Locate charger as far away from battery as DC cables permit.

2. Never place charger directly above battery being charged. Gases from battery will corrode

and damage charger.

3. Never allow battery acid to drip on charger when reading gravity or lling battery.

4. Do not operate charger in a closed-in area or restrict ventilation in any way.

5. Do not set a battery on top of charger.

DC CONNECTION PRECAUTIONS

1. Connect and disconnect DC output clips only after setting any charger switches to off

position and removing AC cord from electric outlet. Never allow clips to touch each other.

2. Attach clips to battery and chassis, as indicated on page 4 in “Follow these steps when

battery is installed in vehicle,” steps 5 and 6, and in “Follow these steps when battery is

outside vehicle,” steps 2 and 4.

3

FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE.

A SPARK NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO

REDUCE RISK OF A SPARK NEAR BATTERY:

1. Position AC and DC cords to reduce risk of damage by hood, door, or moving engine part.

2. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.

3. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger

diameter than NEGATIVE (NEG, N, -) battery post.

4. Determine which post of battery is grounded (connected) to the chassis. If negative post

is grounded to chassis (as in most vehicles), see step 5. If positive post is grounded to the

chassis, see step 6.

5. For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to

POSITIVE (POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK) clip to

vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel

lines, or sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine

block.

6. For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery charger

to NEGATIVE (NEG, N, -) ungrounded post of battery. Connect POSITIVE (RED) clip to

vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel

lines, or sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine

block.

7. When disconnecting charger, turn switches to off, disconnect AC cord, remove clip from

vehicle chassis, and then remove clip from battery terminal.

8. See “Determining Charging Time,” page 9 for length of charge information.

FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE. A

SPARK NEAR THE BATTERY MAY CAUSE BATTERY EXPLOSION. TO

REDUCE RISK OF A SPARK NEAR BATTERY:

1. Check polarity of battery posts. POSTIVE (POS, P, +) battery post usually has a larger

diameter than NEGATIVE (NEG, N, -) post.

2. Attach at least a 24-inch, 6-gauge (AWG) insulated battery cable to NEGATIVE (NEG, N, -)

battery post.

3. Connect POSTIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery.

4. Position yourself and free end of cable as far away from battery as possible. Then connect

NEGATIVE (BLACK) charger clip to free end of cable.

4

5. Do not face battery when making nal connection.

6. When disconnecting charger, always do so in reverse sequence of connecting procedure and

break rst connection while as far away from battery as practical.

7. A marine (boat) battery must be removed and charged on shore. To charge it on board

requires equipment specially designed for marine use.

GROUNDING AND AC POWER CORD CONNECTION

Charger should be grounded to reduce risk of electric shock. Charger is equipped with an electric

cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged

into an outlet that is properly installed and grounded in accordance with all local codes and

ordinances.

DANGER: Never alter AC cord or plug provided. If it will not t outlet, have proper outlet

installed by a qualied electrician. Improper connection can result in a risk of an electric shock.

This battery charger is for use on a nominal, 120-volt circuit, and has a grounding plug that

looks like the plug illustrated in (A) below. A temporary adapter, which looks like the adapter

illustrated in (B) and (C), may be used to connect this plug to a two-pole receptacle, as shown

in (B), if a properly grounded outlet is not available. The temporary adapter should be used only

until a properly grounded outlet can be installed by a qualied electrician.

DANGER: Before using adapter as illustrated, be certain that center screw of outlet plate is

grounded. The green-colored rigid ear or lug extending from adapter must be connected to a

properly grounded outlet. Make certain it is grounded. If necessary, replace original outlet cover

plate screw with a longer screw that will secure adapter ear or lug to outlet cover plate and make

ground connection to grounded outlet.

5

ASSEMBLY INSTRUCTIONS

CAUTION: You must attach the handle before operating the charger.

REQUIREMENTS

• handle

• four screws

• screwdriver

ATTACHING THE HANDLE

To attach the charger handle:

1. Locate the handle and four screws provided. The charger comes with one of two types of

handles.

2. Remove the top two screws at the rear from both sides of the charger.

3. Straddle the handle over the charger and align the mounting holes. If the charger has the Type

2 handle, make sure the handle is ush with the edge of the charger. Refer to the drawing

below.

4. Attach the handle with the four screws and tighten securely.

6

Notice offset of holes

to orient handle correctly.

OPERATING INSTRUCTIONS

CAUTION: The charger must be fully assembled before operating. Refer to “Assembly

Instructions,” page 6 for instructions.

The Professional Charger and Starter models CBC 7600 and CBC 7700 charge lead-acid

batteries. You can use the chargers to:

• charge a discharged battery

• perform an engine start to a discharged battery

The CBC 7700 produces a higher current than the CBC 7600 for the normal charge, fast charge,

and engine start. It also contains a voltmeter.

CONTROLS

AMMETER

The AMMETER shows the amount of amps owing from the charger to the battery.

• CHARGE is the green area with normal charging current.

• START is the red area with high current for engine crank-assist. For more information about

engine crank-assist, refer to “Engine Start,” page 8.

VOLTMETER (CBC 7700 only)

The VOLTMETER shows the battery voltage and percentage of the state of charge.

TIMER

The TIMER switch is on the upper right of the charger.

• OFF disconnects the output of the charger.

• HOLD is for charging times longer than 120 minutes.

RATE/VOLTAGE CONTROL

The RATE/VOLTAGE CONTROL switch is on the upper left of the charger. It controls the

voltage and current.

• SLOW CHARGE is 15 A for 12 V batteries.

• FAST CHARGE is 35 A for 24 V batteries or 65 A (70 A for CBC 7700) for 6 V batteries.

• MEDIUM CHARGE is 30 A for 12 V batteries.

• FAST CHARGE is 65 A (70 A for CBC 7700) for 12 V and parallel batteries. Do not use on

small, low capacity batteries.

• ENGINE START is 275 A (300 A for CBC 7700) for cranking or starting an engine with 12

V battery.

7

FEATURES

ENGINE START

The ENGINE START setting on the RATE/VOLTAGE CONTROL switch provides high current

to crank-assist or start a vehicle with a discharged battery. This feature helps you start the vehicle

to drive it to a location for service.

OVERLOAD PROTECTION

The charger uses output circuit and thermal breakers to prevent overheating and damage to the

charger and vehicle.

DETERMINING THE STATE OF CHARGE

The state of charge is a percentage of the battery charge at a certain temperature. To determine

the state of charge, use a hydrometer, voltmeter, or battery analyzer, depending on the type of

battery you are charging.

NOTE: For the CBC 7700, you can use the percentage scale on the voltmeter as the state of

charge.

For a rellable-top battery, use a hydrometer. A hydrometer is a syringe that takes battery acid

from battery cells to indicate the gravity of the battery acid. The gravity indicates the battery

state of charge at a temperature. The table below shows the state of charge for different gravity

readings:

**Initial gravity readings vary with the battery type and manufacturer.

Contact the battery seller or manufacturer for this information.

For a sealed-top (maintenance-free and recombination) battery, use a high-resolution voltage

battery analyzer.

For any type of battery, use a battery analyzer.

For more information about the type of battery you are charging or how to check the state of

charge, contact the battery seller or manufacturer.

8

2. Move across the row until you nd the amperage for the type of battery you are charging.

Refer to “Controls,” page 7 for the amp values.

The number of hours or minutes is the amount of time you need to charge the battery.

WARNING: High amperage rates might boil and overcharge the battery. Do not leave the

charger unattended. Refer to the battery manufacturer charging instructions.

9

NOTE: The temperature of the battery and the equipment the battery is used with has an effect

on battery efciency and system power requirements. For example, at 0

o

F (-18

o

C), a battery is

operating at 40% of its rated efciency, while the engine requires over twice the power at 80

o

F

(27

o

F).

DETERMINING CHARGING TIME

To determine charging time for the battery, you can use a chart or a formula.

To use the chart:

1. Locate the state of charge (SOC) percentage, reserve capacity (RC), and voltage in the

table below for the type of battery you are charging.

To use the formula:

(reserve capacity in minutes) + 15.5 = amp hour capacity

2

(amp hour capacity) x (percent of charge needed) = time in hrs.

charger amp rate setting

(time in hours) x (recharge factor of 1.25) = recharge time

Example: A battery has an reserve capacity of 120 minutes and is discharged 25%. It needs a

75% charge at 40 A:

120 minutes + 15.5 = 75.5 amp hours

2

(75.5 amp hours) x (0.75) = time = 1.4 hours

40-amp charge rate

Then (1.4 hours) x (recharge factor of 1.25) = 1.76 hours or 106 minutes of recharge time.

CONNECTING TO THE CHARGER

To connect to the charger:

1. Make sure the charger is unplugged.

2. Turn the TIMER switch to OFF.

3. Do one of the following based on where the battery is located:

• If the battery is installed in a vehicle, refer to “Follow these steps when battery is

installed in vehicle,” page 4.

• If the battery is outside of the vehicle (not installed), refer to “Follow these steps when

battery is outside vehicle,” page 4.

4. Plug in the charger. Refer to the safety instructions in “Grounding and AC power cord

connection,” page 5.

5. Set the RATE/VOLTAGE CONTROL switch to match the voltage of the battery you are

charging.

6. Turn the TIMER switch to the charge time you determined in the table on page 9.

CAUTION: Monitor the battery for leaking uid or excessive heat. These conditions can damage

the battery. If the battery gets too hot or spews uid, reduce the charge rate or replace the battery.

10

CHECKING THE CHARGED BATTERY

To check the battery you charged:

1. Turn the TIMER to OFF.

2. Unplug the charger.

3. Disconnect the charger clamps.

4. Start the vehicle.

5. If the vehicle does not start after a few attempts, do the steps under “Performing an engine

start” or replace the battery.

NOTE: Before replacing the battery, use a battery analyzer to test it. If the battery is discharged

and still useful, determine if the starting and charging systems are normal.

PERFORMING AN ENGINE START

The engine start powers a vehicle with a discharged battery. You can use this feature when the

battery in a vehicle does not have enough capacity to start the engine.

To do an engine start:

1. Turn the RATE/VOLTAGE CONTROL switch on the charger to a fast charge setting

(30–70 A).

2. Charge the battery for ve minutes.

3. Select ENGINE START and set the TIMER switch to HOLD.

4. Start the engine with the ignition key.

When the engine starts, the alternator in the vehicle charges the battery as long as the

engine runs so the engine starts by itself the next time.

NOTE: The engine might not start on its own the next time you start the vehicle, even if

it starts and runs from this procedure. If it does not, you might have a bad battery.

5. If the engine does not start in three to ve seconds:

a) Stop cranking.

b) Turn the RATE/VOLTAGE CONTROL switch to the fast charge setting (30–70 A).

c) Charge battery for ve minutes.

11

6. If the engine does not start after a second or third attempt, disconnect the charger and

replace the battery.

NOTE: Before replacing the battery, use a battery analyzer to test it. If the battery is

discharged and still useful, determine if the starting and charging systems are normal.

CAUTION: Do not start a vehicle if the battery is not installed properly. Damage might occur to

the electrical system.

CHARGING MULTIPLE BATTERIES

PARALLEL CHARGING

You can charge batteries of the same type and voltage rating by connecting them in parallel.

Charging two batteries in parallel takes twice as long. Charge time increases with the number

of batteries. Rate of charge decreases with the number of batteries. Each battery receives 1/2

the amount of charge on the ammeter. For example, if the ammeter shows 40 A, each battery is

receiving a 20 A charge.

SERIES CHARGING

You can charge batteries of the same type and voltage by connecting them in a series. The

RATE/VOLTAGE CONTROL switch is the sum of the voltages and current through the

batteries. This number is the amount of charge on the ammeter.

For example, charging two 12 V batteries in a series requires a 24 V setting on the RATE/

VOLTAGE CONTROL switch. If the ammeter shows 30 A, each battery is receiving a 30 A

charge.

12

MAINTENANCE INSTRUCTIONS

The charger contains high quality materials requiring minimal care. For repairs, contact a service

technician.

To maintain the parts to the charger:

• Clean the clamps after you use the charger to prevent corrosion from battery uid.

• Coil the cords when the charger is not used to prevent damage.

TROUBLESHOOTING

NOTE: Cold, sulphated, or damaged batteries can vary readings.

NO METER READING

• Make sure the AC outlet is live.

• Check connections to the battery.

• Refer to “Performing an engine start,” page 11. A breaker might have opened. The output

breaker pops when it opens and resets automatically in a few minutes. The thermal breaker

resets automatically in about 15–30 seconds.

HIGH METER READING

• Make sure the battery connections are not reversed.

• Replace the battery. The battery might have dead cells.

CUSTOMER SERVICE

For customer service (Monday through Friday), call:

• 1-888-263-4906, 7 a.m. to 5:00 p.m. (Central Time)

13

LIMITED WARRANTY

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,

MOUNT PROSPECT, ILLINOIS, 60056-2179 MAKES THIS LIMITED WARRANTY

TO THE ORIGINAL PURCHASER AT RETAIL OF THIS PRODUCT. THIS LIMITED

WARRANTY IS NOT TRANSFERABLE.

Schumacher Electric Corporation warrants this battery charger against defective material or

workmanship. If such should occur, the unit will be repaired or replaced at the option of the

manufacturer. It is the obligation of the purchaser to forward the unit together with proof of

purchase, transportation and / or mailing charges prepaid to the manufacturer or its authorized

representative. This limited warranty is void if the product is misused, subjected to careless

handling, or repaired by anyone other than the factory or other authorized factory representative.

The manufacturer makes no warranty other than this limited warranty and expressly excludes any

implied warranty including any warranty for consequential damages.

This is the only express limited warranty and the manufacturer neither assumes nor authorizes

anyone to assume or make any other obligation towards the product other than this express

limited warranty. The manufacturer makes no warranty of merchantability or tness for purpose

of this product and expressly excludes such from this limited warranty. Some states do not allow

the exclusion or limitation of incidental or consequential damages or length of implied warranty

so the above limitations or exclusions may not apply to you. “This warranty gives you specic

legal rights, and you may have other rights which vary from state to state.”

14

Send Warranty Product Repairs to:

Schumacher Electric Corporation, Warranty Service Department

1025 East Thompson, Hoopeston, IL 60942-0280

Phone: 1-888-263-4906 (Hours: 7 a.m. – 4:30 p.m. CST)

Schumacher Electric Corp.

801 Business Center Drive, Mount Prospect, IL 60056-2179

Manuel d’Instruction

Chargeurs et Démarreurs

Professionnels Rapides

CBC 7600 et CBC 7700

15

16

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

Lisez et gardez ce manuel d’instructions. Gardez-le toujours avec le chargeur.

ATTENTION : Le chargeur devra être complètement assemblé avant l’opération. Consultez les

« Instructions d’Assemblage »à la page 23 pour les instructions.

1. GARDEZ CES INSTRUCTIONS—Ce manuel contient d’importantes instructions de

sécurité et d’opération pour les chargeurs de batteries CBC 7600 et CBC 7700.

2. L’utilisation d’accessoires non-recommandés ou vendus par le fabricant des chargeurs de

batteries pourrait engendrer des risques d’incendie, de choques électriques, ou de dommages

personnels.

3. Pour réduire le risque de dommages aux prises et aux cordes, tirez toujours par la prise

lorsque vous débranchez le chargeur, et non par la corde.

4. Une corde de prolongation ne devra pas être utilisée à moins qu’absolument nécessaire.

L’utilisation d’une corde incorrecte pourrait engendrer des risques d’incendie et de choques

électriques. Si une corde de prolongation doit être utilisée, assurez-vous que:

a) Les ches de la prise de la corde de prolongation ont le même numéro, la même taille, et la

même forme que ceux de la prise du chargeur;

b) La corde de prolongation est correctement installée et en bonnes conditions électriques; et

c) La taille du l est sufsamment grande pour la classication en ampères C.A. du chargeur,

comme spécié dans la table suivante :

5. Ne pas opérer le chargeur avec des cordes ou des prises endommagées. Remplacez la corde

ou la prise immédiatement.

6. MISE EN GARDE : La manipulation du cordon de cet appareil ou du cordon des accessoires

vendus avec ce produit peut entraîner une exposition au plomb, un produit chimique reconnu

par l’État de la Californie pour causer le cancer ainsi que des anomalies congénitales ou autre

dommage génétique. Lavez soigneusement vos mains après toute manipulation.

7. Ne pas opérer le chargeur s’il a reçu un coup fort, s’il est tombé, ou s’il est endommagé d’une

autre forme quelconque. Portez-le chez un magasin de réparations.

17

8. Ne pas démonter le chargeur. Portez-le chez un magasin de réparations qualié lorsqu’il

requiert service ou réparation. Le montage incorrecte pourrait causer des risques de choques

électriques ou d’incendie.

9. Pour réduire les risques de choques électriques, débranchez le chargeur de la prise avant de

réaliser l’entretien ou le nettoyage. Arrêter les commandes ne réduira pas les risques.

AVERTISSEMENT: RISQUE DE GAZ EXPLOSIFS

1. TRAVAILLER À PROXIMITÉ D’UNE BATTERIE AU PLOMB-ACIDE EST

DANGEREUX. LES BATTERIES DÉGAGENT DES GAZ EXPLOSIFS PENDANT LEUR

OPÉRATION NORMALE. POUR CETTE RAISON, IL EST TRÈS IMPORTANT QUE

VOUS LISIEZ CE MANUEL CHAQUE FOIS AVANT D’UTILISER LE CHARGEUR ET

QUE VOUS SUIVIEZ ATTENTIVEMENT LES INSTRUCTIONS.

2. Pour réduire le risque d’une explosion de la batterie, suivez ces instructions et celles publiées

par le fabricant de la batterie et par le fabricant de tout autre équipement que vous utilisez à

proximité d’une batterie. Révisez les inscriptions d’avertissement sur ces produits et sur le

moteur.

PRÉCAUTIONS PERSONNELLES

1. Quelqu’un devra être à la portée de votre voix ou sufsamment proche pour venir à votre

secours lorsque vous travaillez près d’une batterie au plomb-acide.

2. Ayez beaucoup d’eau fraîche et du savon auprès de vous au cas d’un contact de l’acide de la

batterie avec votre peau, vos vêtements, ou vos yeux.

3. Portez de la protection pour les yeux et de la protection pour vos vêtements. Évitez toucher vos

yeux lorsque vous travaillez près d’une batterie.

4. Si l’acide de la batterie entre en contact avec votre peau ou vos vêtements, lavez-les

imméditement avec du savon et de l’eau. Si l’acide entre dans vos yeux, innondez-les

immédiatement avec de l’eau froide pendant un minimum de 10 minutes et cherchez de

l’attention médicale immédiatement.

5. Ne JAMAIS fumer ou permettre la production d’étincelles ou de ammes à proximité d’une

batterie ou d’un moteur.

6. Faites très attention pour réduire le risque de chute d’un outil en métal sur la batterie. Cela

pourrait produire des étincelles ou un court-circuit dans la batterie ou dans une autre pièce

électrique qui pourrait provoquer une explosion.

7. Enlevez les articles personnels en métal, tels que bagues, bracelets, colliers, et montres,

lorsque vous travaillez avec une batterie au plomb-acide. Une batterie au plomb-acide pourrait

produire un courant de court-circuit sufsante pour souder une bague ou d’autres objets

métalliques, ainsi provoquant de graves brûlures.

18

La page charge ...

Schumacher Electric CBC 7700 Manuel utilisateur

Ce manuel convient également à

Schumacher Electric CBC 7700 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents