Ideal 61-797 Mode d'emploi

1

#61-797

Digital Insulation Meter

Instruction Manual

2

Register your product and access more information at

www.idealindustries.com

Read First: Safety Information

Understand and follow operating instructions carefully. Use the meter,

test leads and all accessories only as specified in this manual; otherwise,

the protection provided by the meter can be impaired.

WARNING

To avoid possible electric shock, personal injury or death,

follow these guidelines:

• Do not use if meter appears damaged. Visually inspect the meter to

ensure case and jaws are not cracked.

• Inspect and replace test leads if insulation is damaged, metal is

exposed, or probes are cracked. Pay particular attention to the

insulation surrounding the connectors.

• Always ensure the meter, test leads and all accessories meet or exceed

the measurement category required in the working environment. (i.e.

CAT rating)

• Note that the measurement category and voltage rating of

combinations of the meter, the test leads, and the accessories is the

lowest of the individual components.

• Do not use meter if it operates abnormally as protection maybe

impaired.

• Do not use during electrical storms or in wet weather.

• Do not use around explosive gas, dust, vapor, amperage or in damp or

wet environments.

• Do not apply more than the rated voltage to the meter.

• Remove the test leads from the input jacks before measuring current.

• Replace battery as soon as battery indicator appears to avoid

false readings.

• Remove the test leads from the meter prior to removing battery cover.

• Do not use without the battery and battery cover properly installed.

• Do not attempt to repair this unit as it has no user-serviceable parts.

• Use the proper terminals, functions and range for your measurements.

• Never ground yourself when taking electrical measurements.

• Connect the black common lead to ground or neutral before applying

the red test lead to potential voltage. Disconnect the red test lead from

the voltage first.

• Keep fingers behind the guard rings of the probe tips.

• Voltages exceeding 30VAC or 60VDC pose a shock hazard so use

caution.

3

CAUTION

To protect yourself, think “Safety First”:

• Comply with local and national safety codes.

• Use appropriate personal protective equipment such as face shields,

insulating gloves, insulating boots, and/or insulating mats.

• Before each use:

- Perform a continuity test by touching the test leads together to

verify the functionality of the battery and test leads.

- Use the 3 Point Safety Method. (1) Verify meter operation by

measuring a known voltage. (2) Apply meter to circuit under test.

(3) Return to the known live voltage again to ensure proper

operation.

• Always work with a partner.

Instrument - Description

1. Display

2. Features

Pass indicator

High Voltage

indicator

3. Function Selector

& Power On/Off

4. Ω Input

5. V Insulation Input

6. Common Input

4

Feature Callouts

1. LCD Display - 4000 count

2. Push-Buttons for features

3. Function Selector to turn the Power On or Off and to select

a function.

4. Input Terminal for Ω function.

5. Input Terminal for V insulation functions.

6. Common (Ground reference) input Terminal for all

functions.

Symbols on the Unit

Test Leads

Risk of Danger. Important Information. See Manual.

Hazardous voltage. Risk of electrical shock.

Application around and removal from Hazardous Live conductors is permitted.

AC (Alternating Current)

DC (Direct Current)

Earth Ground

CAT II

Measurement Category II applies to test and measuring circuits connected

directly to utilization points (socket outlets and similar points) of the low-

voltage installation

CAT III

Measurement Category III applies to measuring circuits connected to the

distribution part of the building’s low-voltage installation

CAT IV

Measurement Category IV applies to test and measuring circuits connected at

the source of the building’s low-voltage installation

~

...

Guard ring

5

When connecting the test leads to the DUT (Device Under Test) connect

the common (COM) test lead before connecting the live lead; when

removing the test leads, remove the live test before removing the

common test lead.

The ﬁgures on the following pages show how to make basic

measurements.

Measuring ACV/DCV : Auto Sense Function

If the measured voltage is above 660 V ac/dc, “>660Vac/dc”

will appear on the display.

Auto sense mode: The meter displays ACV or DCV whichever is higher

(>0.3V).

If the measured voltage is above 660Vac/dc, “660Vac/dc” will appear on

the display.

6

Measuring Earth-Bond Resistance

Measuring ACV/DCV: Auto sense +LPF function

PRESS

The Low Pass Filter (LPF) mode when activated in the AC Voltage Mode

rejects or blocks unwanted voltage at frequencies > than 1k HZ. The Low

Pass ﬁlter can greatly improve measurements on complex wave forms

such as adjustale speed drives or variable frequency drives.

7

1. Before starting the test :

(a) The circuit under test must be completely de-energized.

Check the fuse before testing.

Connecting to an energized circuit while the test is active will

blow the fuse.

See Testing the fuse later in this manual.

If the detected voltage is above 2V, “>2V” will appear on the

display.

In this condition, the test is inhibited.

(b) Short the test leads before measurement, and press the blue

button to compensate the probe resistance for <2Ω.

2. Lock mode : Press the Lock button to enter the Lock Mode.

Then press the TEST button to start the test. The test voltage will

continue to be applied until the TEST/LOCK button is pressed again.

3. The meter displays the “>” symbol and the maximum resistance for

the range when measured resistance is higher than the maximum

display range.

8

Measuring Insulation Resistance

Ω

V

INSULATION

PASS

RECALL PI/DAR

COMPARE

PI DAR

TEST

V

100200

500KMΩ

0

100K

10M

100M

100MK

10Gk

100

Gk

AUTO LOCK APOSENSE

KMΩ

GΩ

µmA

MΩ

COMP STORE LOCK

61-797

>600V

COM

OFF

50V

V

100V

250V

500V

1000V

FUSED

CAT. IV

600V

0

LPF

L

e

a

k

a

g

e

C

u

r

e

n

t

AC

DC

~

AC

DC

~

MEM TEST

+

–

~

Press

&

Hold

TEST

0

100K

10M

100M

100MK

10Gk

100Gk

MΩ

0

100K

10M

100M

100MK

10Gk

100Gk

V

DC

TEST

MΩ

V

DC

=

TEST

LPF

1. Before starting the test:

The circuit under test must be completely de-energized. If the

voltage detected is above 30V, “>30V” will appear on the display.

In this condition, the test is inhibited.

2. Press the blue button to display insulation resistance or Leakage

current during the test or when the test stops.

3. Lock mode: Press the Lock button to enter the Lock Mode. Then

press TEST button to start the test. The test voltage will continue to

be applied until the TEST/LOCK button is pressed again.

4. Release the TEST button before removing the test leads (to enable

the tester to discharge capacitive circuits). If the screen displays

volts, wait until it reaches zero.

5. The meter displays the “>” symbol and the maximum resistance

for the range when measured resistance is higher than the maximum

display range.

9

Using the Compare Function

Measuring PI/DAR

1. Before starting the insulation test:

Press the COMP button to select the compare value among

100kΩ, 200kΩ, 500kΩ, 1MΩ, 2MΩ, 5MΩ, 10MΩ, 20MΩ,

50MΩ, 100MΩ, 200MΩ and 500MΩ

2. If the measured value is greater than the selected compare value, the

green Pass indicator will illuminate.

PI (Polarization Index) = R10-min/R1-min

DAR (Dielectric Absorption Rations) = R1-min/R30-sec

R10-min : the insulation resistance measured at the 10 minute mark

after pressing the TEST button.

R1-min : the insulation resistance measured at the 1 minute mark after

pressing the TEST button.

R30-sec : the insulation resistance measured at the 30 second mark after

pressing the TEST button.

10

The measured values of DAR test

DAR = R1-min/R30-sec

When the measured resistance is higher than the maximum range, the

screen will display “Err” symbol for PI/DAR value.

TEST button : Press once to start/interrupt the PI /DAR test.

Blue button : Use to display and check the time left of the PI/DAR test.

The measured values of PI test

PI = R10-min/R1-min

If the reading for DAR is bigger than 1.3 or PI is bigger than 2, it indicates

that the insulation is good. On many installations, the quality of the

insulation is so good that both the initial measured value and the

subsequently measured value (when performing the PI or DAR tests),

will be the maxium that the meter can read. Dividing one into the other

will of course read the value of 1, which in this case may be perfectly

good. It is strongly recommended that in all cases, you contact

the manufacturer of the device under test or the appropriate

manual, to ensure that any reading meets the manufacturers

speciﬁcation for determining if a part is good or bad.

11

Using the Store Function

Store/Recall button:

The screen will be ﬂashing the MEM symbol and the number of the

stored data twice when the Store/Recall button is pressed.

1. Press once to store the voltage value during voltage test

2. Press once to store the PI/ DAR, insulation or Earth-bond

resistance value when the individual test is completed.

3. The memory is divided into ﬁve segments, each segment has

100 maximum data points. The method to store the data is ﬁrst

in/ﬁrst out when the memory is full.

Table: The stored values of the individual test

segments

Voltage

Earth-Bond

resistance

Insulation

resistance

50~1000V

DAR PI

items

1 Voltage Resistance Resistance DAR value PI value

2 Leakage

Current

R30-sec R1-min

3 Test voltage R1-min R10-min

Using the Recall Function

Press the Store/Recall button > 2 sec to enter the RECALL mode.

If the memory is empty, the meter will display the “ nOnE ” symbol.

Search the stored value under RECALL mode

Note: Press the Store/Recall button > 5 sec to clear the stored data.

The screen will be ﬂashing MEM symbol and “cLr” on reading twice.

12

Read the stored value of insulation test under RECALL mode

Read the stored value of DAR test under RECALL mode

Press the PI/DAR button > 2 sec to choose the PI/DAR function, and

Press the Store/Recall button > 2 sec to enter the RECALL mode.

13

Read the stored value of PI test under RECALL mode

Auto Power Off (Battery Saver)

Restore power by switching the Function Selector or by pressing

any button.

Auto Backlight

The backlight is automatically turned on in a dark environment.

Buzzer

The Meter beeps once for every valid key-press, and beeps twice for

every invalid key-press.

14

Ω

V

INSULATION

PASS

RECALL PI/DAR

TEST

MΩ

COMP STORE LOCK

61-797

>600V

COM

OFF

50V

V

100V

250V

500V

1000V

FUSED

CAT. IV

600V

0

LPF

L

e

a

k

a

g

e

C

u

r

e

n

t

TEST

Power-up options:

Press button while turning meter on from OFF position.

Lock button: display of the software version.

Store button: reset all stored data.

Blue button: disable auto power off.

Battery and Fuse Replacement

Refer to the following ﬁgure to replace fuse and batteries.

Testing the Fuse

CAUTION:

• Use only a fuse with the

amperage, interrupt, voltage,

and speed rating speciﬁed.

• Fuse rating : Fast, 315mA,

1000V, Min Interrupt

Rating 10000A.

• Replace the batteries as

soon as the low battery

indicator “ ” appears,

to avoid false readings.

• When the battery is too low

for reliable operation, the meter

displays “bAtt.” The meter will

not operate at all until the battery

is replaced.

• 1.5V x 4 alkaline batteries.

• Remove the test leads before

testing the fuse.

• If the display is reading FUSE,

the fuse is bad and should be

replaced.

15

Speciﬁcations

General Speciﬁcations

Display: 4000 count

Refresh Rate: 2.0x/sec.

Over range: “OL” is displayed

Polarity: Automatic (no indication for positive

polarity); Minus (-) sign for negative

polarity

Auto Power Off: After 20 minutes of non-use

Low Battery: is displayed if battery voltage drops

below operating voltage.

Altitude: 6561.7 ft (2000m)

Accuracy: Stated accuracy at 73º ±41ºF (23º ±5ºC),

< 80% R.H.

Batteries: (4) 1.5V AA LR6

Battery Life: 40 hrs./1000 test @ 1000V/1MΩ

Fuse: 315mA/1000V (#F-797)

Operating environment: 32º to 104ºF (0º to 40ºC) at < 75% R.H.

Storage environment: -4° to 140°F (-20º to 60ºC) at < 80% R.H.

Weight: 22.3 oz (630g)

Size: 8.1”H x 3.7”W x 2.0”D

(207mmH x 95mmW x 52mmD)

Assecories Included: Test leads (TL-797, TL-797 RP),

(4) AA batteries, Operating Instructions

Shock Vibration: Sinusoidal vibration per MIL-T- 28800E

(5 ~ 55 Hz, 3g maximum).

Safety Certiﬁcation: Complies with UL/IEC/EN 61010-1,

61010-031, EN61557, EN 61326-1 +1A (EMC)

Cat IV-600V

Equipment protected by double insulation.

Instrument has been evalted and complies with insulation

(overvoltage) catergory IV. Pollution degree 2 in accordance with

IEC-644. Indoor use.

16

Maintenance

Clean the case with a damp cloth and mild detergent. Do not use

abrasives or solvents.

Service and Replacement Parts

No user-serviceable parts.

For replacement parts or to inquire about service information, contact

IDEAL INDUSTRIES, INC. at 1-877-201-9005 or visit our website @

www.testersandmeters.com.

Dispose of waste electrical and electronic equipment

In order to preserve, protect and improve the quality of environ-

ment, protect human health and utilize natural resources prudently and

rationally, the user should return unserviceable product to relevant

facilities in accordance with statutory regulations. The crossed-out

wheeled bin indicates the product needs to be disposed seperately and

not as municipal waste.

Dispose of used batteries/accumulators

The user is legally obliged to return used batteries and accumu-

lators. Disposing used batteries in the household waste is prohibited!

Batteries/accumulators containing hazardous substances are marked

with the crossed-out wheeled bin. The symbol indicates that the product

is forbidden to be disposed via the domestic refuse. The chemical

symbols for the respective hazardous substances are Cd = Cadmium,

Hg = Mercury, Pb = Lead

You can return used batteries/accumulators free of charge to any

collecting point of your local authority, our stores, or where

batteries/accumulators are sold. Consequently you comply with your

legal obligations and contribute to environmental protection.

17

Electrical Speciﬁcations

Accuracy is ±(% reading + number of digits) at 23°C ±5°C < 80%RH.

Voltage Measurement

Function Range Accuracy

DCV 600.0V ±1%+5dgt

ACV 600.0V

±(1.5%+5dgt)(50~60Hz)

±(2%+5dgt)(61~500Hz)

LPF ACV 600.0V

±(1.5%+5dgt)(50~60Hz)

±(5%+5dgt)(61~400Hz)

Initial Voltage: ≥ AC 0.6V.

Over voltage protection: 600 V AC RMS/DC.

The cut-off frequency of the low pass ﬁlter: 1 kHz.

Input Impedance: 3MΩ // less than 100pF.

CMRR / NMRR: (Common Mode Rejection Ratio)

(Normal Mode Rejection Ratio)

V

AC

: CMRR > 60dB at DC, 50Hz / 60Hz

V

DC

: CMRR > 100dB at DC, 50Hz / 60Hz

NMRR > 50dB at DC, 50Hz / 60Hz

AC Conversion Type: AC conversions are ac-coupled, true rms

responding, calibrated to the sine wave input.

For non-sine wave add the following Crest Factor corrections:

For Crest Factor of 1.4 to 2.0, add 1.0% to accuracy.

For Crest Factor of 2.0 to 2.5, add 2.5% to accuracy.

For Crest Factor of 2.5 to 3.0, add 4.0% to accuracy.

CF 3 @ 330V, 2 @ 500V

Earth-bond resistance Measurement

Function Range Accuracy

Earth-Bond

Resistance

40.00Ω ±(1.5%+5dgt)*

400.0Ω

±(1.5%+3dgt)

4000Ω

40.00kΩ

*<1.00Ω add 3dgt

Open Circuit Test Voltage : > 4.0V,<8V, Short Circuit Current : > 200.0mA

Live Circuit Detection: if > 2V ac/dc at inputs, test inhibited.

18

Insulation resistance Measurement

Function Range Accuracy

Insulation

Resistance

4.000MΩ

40.00MΩ

±(1.5%+5dgt)

400.0MΩ

4000MΩ

±(3%+5dgt)

4.1GΩ ~ 20.0GΩ ±(10%+3dgt)

Test Voltage vs. Maximum resistance range:

50V/50.0MΩ, 100V/100.0MΩ, 250V/250.0MΩ, 500V/500MΩ, and

1000V/20.0GΩ.

Test Voltage vs. Minimum resistance (with test current=1mA):

50V/50kΩ, 100V/100kΩ, 250V/250kΩ, 500V/500kΩ and

1000V/1MΩ.

Test Voltage Accuracy: -0%,+20%

Short Circuit Test Current: 1mA(nominal)

Auto discharge function: discharge time <1 sec for C <1μF

Maximum Capacitive load: Operable with up to 1μF load

Live Circuit Detection: if >30V ac/dc at inputs, test inhibited

19

Warranty Statement

This tester is warranted to the original purchaser against defects in

material and workmanship for two years from the date of purchase.

During this warranty period, IDEAL INDUSTRIES, INC. will, at its option,

replace or repair the defective unit, subject to veriﬁcation of the defect or

malfunction.

This warranty does not cover fuses, batteries or damage from abuse,

neglect, accident, unauthorized repair, alteration, or unreasonable use of

the instrument.

Any implied warranties arising out of the sale of an IDEAL product,

including but not limited to implied warranties of merchantability and

ﬁtness for a particular purpose, are limited to the above. The

manufacturer shall not be liable for loss of use of the instrument or other

incidental or consequential damages, expenses, or economic loss, or for

any claim or claims for such damage, expenses or economic loss.

State laws vary, so the above limitations or exclusions may not apply

to you. This warranty gives you speciﬁc legal rights, and you may also

have other rights which vary from state to state.

IDEAL INDUSTRIES, INC.

Sycamore, IL 60178, U.S.A.

877-201-9005 Technical Hotline

www.idealind.com

ND 7039-3 Made in Taiwan

20

#61-797

Medidor digital de aislamiento

Manual de instrucciones

La page charge ...

Ideal 61-797 Mode d'emploi

Ce manuel convient également à

Ideal 61-797 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents