Hatco KWM Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
KWM Series
Catégorie
Gaufriers
Taper
Le manuel du propriétaire
P/N 07.04.924.00 © 2020 Hatco Corporation
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 16
AVERTISSEMENT
Waffle Makers
Gaufriers
KWM Series • Série KWM
Installation and Operating Manual
Manuel d’installation et d’utilisation
2
Form No. KWMM-0220
English
INTRODUCTION
Waffle Makers cook continuous, excellent-quality waffles
for commercial kitchens and display cooking locations. The
adjustable temperature control enables operators to cook
consistent quality waffles from a variety of different batters.
Exclusive, removable top and bottom heating element packs
provide exceptional heat distribution over the entire waffle plate
surface. The Waffle Maker’s easy clean System
®
provides
quick removal and easy cleaning of the waffle plates.
Waffle Makers are products of extensive research and field
testing. The materials used were selected for maximum
durability, attractive appearance, and optimum performance.
Every unit is inspected and tested thoroughly prior to shipment.
This manual provides installation, safety, and operating
instructions for Waffle Makers. Hatco recommends all
installation, operating, and safety instructions appearing in this
manual be read prior to installation or operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Description ................................................................4
Model Designation ...............................................................4
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Charts ....................................................... 5
Dimensions .......................................................................... 5
Installation .............................................................................6
General ................................................................................ 6
Operation ...............................................................................8
General ................................................................................ 8
Control Panel .......................................................................8
Seasoning the Waffle Plates ...............................................8
Operating the Unit ...............................................................8
Maintenance ........................................................................10
General .............................................................................. 10
Daily Cleaning ...................................................................10
Removing the Waffle Plates .............................................. 11
Troubleshooting Guide ......................................................14
Options and Accessories ..................................................14
Limited Warranty ................................................................15
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and purchase
date of the unit in the spaces below (specification label located
on the bottom the unit). Please have this information available
when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. _________________________________________
Voltage ___________________________________________
Date of Purchase ___________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00  to 5:00  Monday–Friday,
Central Time (CT)
(Summer Hours — June to September:
7:00  to 5:00  Monday–Thursday
7:00  to 4:00  Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
CONTENTS
Form No. KWMM-0220
3
English
IMPORTANT SAFETY INFORMATION
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a maximum of 104°F (40°C).
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• Do not pull unit by power cord.
• Do not allow power cord to hang over edge of counter.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Never leave unit unattended during use.
Do not use unit for any purpose other than for which it is
designed.
WARNING
FIRE HAZARD:
• Locateunitaminimumof8″(203mm)fromcombustible
walls and materials. If safe distances are not maintained,
discoloration or combustion could occur.
• Do not obstruct air ventilation openings on outer
housing of unit. Unit combustion or malfunction may
occur.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Avoid
unnecessary contact with unit.
• Do not come in contact with waffle plates during
operation. Both plates are very hot.
• Allow unit to cool before performing any cleaning,
adjustments, or maintenance.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level and strong
enough to support weight of unit and contents.
NOTICE
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures and grease could cause damage to unit.
Damage to any countertop material caused by heat
generated from Hatco equipment is not covered under
the Hatco warranty. Contact manufacturer of countertop
material for application information.
For steel surfaces, use non-abrasive cleaners and cloths
only. Abrasive cleaners and cloths could scratch finish of
unit, marring its appearance and making it susceptible to
soil accumulation.
Do not use harsh chemicals such as bleach, cleaners
containing bleach, or oven cleaners to clean this unit.
Do not attempt to cool hot waffle plates quickly, such as by
immersing in water. Damage to plates will occur.
This unit is intended for commercial use only—NOT for
household use.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
4
Form No. KWMM-0220
English
MODEL DESCRIPTION
All Models
Waffle Makers consist of an easy-to-clean stainless steel
frame. The units feature removable cast iron waffle plates,
an adjustable Temperature Control(s) with a range from
120°F–570°F (50°C–300°C), a power indicator, a heating
indicator, and a removable drip tray. Waffle plates are available
for Brussels (Belgian—square or round), Liège, or bubble-style
waffles.
KWM09 Models
These models are designed with 90° hinged waffle plates and

and plug. This style of waffle maker is designed for reheating
pre-cooked waffles.
Temperature Control
Drip Tray
Top
Waffle
Plate
Bottom
Waffle
Plate
Power Indicator
Heating Indicator
KWM09 Models (Brussels waffle plates shown)
KWM18 Models
These models are designed with 180° hinged waffle plates and

and plug. This style of waffle maker is designed for cooking
waffles from batter/dough as well as reheating pre-cooked
waffles.
Temperature Control
Front
Drip Tray
Power Indicator
Heating Indicator
Rear
Drip Tray
Front
Waffle Plate
Rear
Waffle Plate
KWM18 Models
(Brussels waffle plates shown)
KWMSL Models
These models are designed with a swivel system that rotates

(1829 mm) power cord and plug. This style of waffle maker
is designed for cooking waffles from batter/dough as well as
reheating pre-cooked waffles.
Drip Tray
Top
Waffle
Plate
Bottom
Waffle
Plate
Temperature
Control
Power
Indicator
Heating
Indicator
Detachable Power Cord
KWMSL Models
(Liège waffle plates shown)
Refer to the OPTIONS AND ACCESSORIES section for
additional items available with Waffle Makers.
Form No. KWMM-0220
5
English
Model Voltage Watts Amps Plug Configuration Unit Weight
KWM09-1BR46
120 V 1440 W 12 A NEMA 5-15P
37 lbs. (17 kg)
KWM09-1LG47
KWM09-1BR46 208–240 V
†
1352–1800 W 6.5–7.5 A NEMA 6-20P
KWM18-1BR35
120 V 1440 W 12 A NEMA 5-15P
40 lbs. (18 kg)
KWM18-1BR46
208–240 V
†
1352–1800 W 6.5–7.5 A NEMA 6-20P
KWM18-1LG47
120 V 1440 W 12 A NEMA 5-15P
208–240
†
1352–1800 W 6.5–7.5 NEMA 6-20P
KWM18-1RO7
120 V 1440 W 12 A NEMA 5-15P
53 lbs. (24 kg)
KWM18-1BU
KWM18-16CH 44 lbs. (20 kg)
KWM18-2BR46
208–240 V
†
2704–3600 W 13–15 A NEMA 6-20P 78 lbs. (35 kg)KWM18-2LG47
KWM18-32CH
KWMSL-4BR46
208–240 V
†
1953–2600 W 9.4–11.3 A NEMA 6-20P 68 lbs. (31 kg)
KWMSL-2LG413
MODEL DESIGNATION
SPECIFICATIONS
K W M xx - x xx xx
Waffle Maker
Waffle Maker Style:
09 = 90˚ Hinged Plates
18 = 180˚ Hinged Plates
SL = 180˚ Swivel Plates
1 = Single Head
2 = Dual Head
16 = Single Head, 16 Churros
32 = Dual Head, 32 Churros
Waffle Plate Dimple Count:
35 = 3 x 5 Brussels
46 = 4 x 6 Brussels
47 = 4 x 7 Liège
7 = 7″ Brussels Round
413 = 4 x 13 Liège
Waffle Plate Style:
BR = Brussels (Belgian)
RO = Round Brussels
LG = Liège
BU = Bubble
CH = Churro
Electrical Rating Chart
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug. Plugs are supplied according to the application.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install proper voltage and size electrical receptacle.
NOTE: Receptacle not supplied by Hatco.
1(0$3
1(0$3
Plug Configurations
†
Unit is designed to operate on supply voltages between 208 V and 240 V.
6
Form No. KWMM-0220
English
Model
Overall
Width (A)
Overall
Depth (B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
Unit
Width (F)
Unit
Depth (G)
KWM09-1BR46
15
(380 mm)
18-11/16
(473 mm)
9-1/8
(232 mm)
9-5/8
(243 mm)
9-11/16
(245 mm)
10-1/4
(260 mm)
12-7/16
(315 mm)
KWM09-1LG47
KWM18-1BR35

(430 mm)
23-3/16
(589 mm)
9-1/8
(232 mm)
9-5/8
(243 mm)
14-9/16
(369 mm)
10-1/4
(260 mm)
17-3/8
(440 mm)
KWM18-1BR46
KWM18-1LG47
KWM18-16CH

(422 mm)
23-5/8
(599 mm)
9-11/16
(246 mm)
14-11/16
(372 mm)
KWM18-1RO7

(415 mm)
26-1/16
(662 mm)
9-1/8
(232 mm)
9-5/8
(243 mm)
16-15/16
(429 mm)
10-1/4
(260 mm)
19-11/16
(500 mm)
KWM18-1BU

(422 mm)
23-5/8
(599 mm)
14-9/16
(369 mm)
17-3/8
(440 mm)
KWM18-2BR46

(740 mm)
23-5/8
(599 mm)
9-1/8
(232 mm)
19-13/16
(503 mm)
14-9/16
(369 mm)
20-1/2
(520 mm)
17-3/8
(440 mm)
KWM18-2LG47
KWM18-32CH

(720 mm)
19-15/16
(506 mm)
14-11/16
(372 mm)
KWMSL-4BR46
N/A
17-3/16
(436 mm)
16-3/16
(410 mm)
19-1/2
(495 mm)
12-3/4
(323 mm)
13-7/16
(340 mm)
9-1/16
(230 mm)
KWMSL-2LG413
Dimensions
KWMSL
Models
C
B
G
A
F
F
D
C
C
A
D
E
B
F
B
G
E
D
E
G
KWM18
Models
KWM09 Models
SPECIFICATIONS
Form No. KWMM-0220
7
English
INSTALLATION
General
Waffle Makers are shipped pre-assembled and ready for
seasoning prior to their first use. Care should be taken when
unpacking the shipping carton to avoid damage to the unit.
The following installation procedure must be performed before
connecting electricity and operating the unit.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
maximum of 104°F (40°C).
FIRE HAZARD:
• Locateunitaminimumof8″(203mm)fromcombustible
walls and materials. If safe distances are not maintained,
discoloration or combustion could occur.
• Do not obstruct air ventilation openings on outer
housing of unit. Unit combustion or malfunction may
occur.
1. Inspect the shipping carton for obvious signs of transit
damage. If damaged, inform the freight company
immediately. CAUTION! Stop! Do not attempt to use
unit if damaged. Contact Hatco for assistance.
2. Remove the unit and any loose components/accessories
from the shipping carton. The following loose components
are included in every Waffle Maker (excluding models
KWMSL-4BR46 and KWMSL-2LG413):
• Handles
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
3. Remove tape and protective packaging from all surfaces
of the unit.
• Make sure to remove all protective film from the stainless
steel surfaces.
4. Inspect the unit for freight damage such as dents in
housing or broken knobs. If damaged, inform the freight
company immediately.
CAUTION
Locate unit at proper counter height in an area that is
convenient for use. Location should be level and strong
enough to support weight of unit and contents.
NOTICE
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures and grease could cause damage to unit.
Damage to any countertop material caused by heat
generated from Hatco equipment is not covered under
the Hatco warranty. Contact manufacturer of countertop
material for application information.
5. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a maximum of 104°F
(40°C). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods
and air conditioning ducts).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
6. Install the handles into the waffle plates, if necessary.
• Thread a handle into the hole on the front of each waffle
plate. Tighten securely.
7. Make sure the drip tray(s) is in position on the base of the
waffle maker.
Handle
Hole
Drip Tray
Drip Tray
Drip
Tray
Base
Installing the handles and drip trays
8
Form No. KWMM-0220
English
OPERATION
General
Waffle Makers are designed for ease of operation. Use the
following information and procedures to operate a Waffle
Maker.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
Control Panel
The following are descriptions of the controls used to operate
a Waffle Maker. All controls are located on the control panel at
the front of the unit.
Power Indicator
The Power Indicator illuminates when the unit is on.
Heating Indicator
The Heating Indicator illuminates when the heating elements
are on and heating the waffle plates.
Temperature Control
The Temperature Control controls the power to the unit as
well as the temperature setting. Turn the Temperature Control
clockwise to turn on and increase the temperature setting.
Turn the Temperature Control counterclockwise to decrease
the temperature setting and turn off the unit. The temperature
range of the unit is 120°–570°F (50°–300°C).
Seasoning the Waffle Plates
Use the following procedure to season the cast iron waffle
plates before using the waffle maker for the first time.
1. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
2. Make sure the drip tray(s) is in position on the base of the
waffle maker.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Avoid
unnecessary contact with unit.
• Do not come in contact with waffle plates during
operation. Plates are very hot.
3. Turn the Temperature Control clockwise to the 570°F
(300°C) temperature setting.
• Both the Power Indicator and the Heating Indicator will
illuminate.
4. Allow the unit to heat for 40 minutes.
5. Turn the Temperature Control counterclockwise to the
520°F (270°C) temperature setting.
6. Allow the unit to adjust to the new temperature for
approximately 5 minutes.
7. Using a heat-resistant, food-safe cooking brush; carefully
apply an oil-based, non-stick shortening evenly onto each
waffle plate. Make sure the shortening makes it to the
bottoms of the grooves in each plate.
NOTE: Do not leave excess shortening in the bottoms of the
groves.
8. Leave the waffle maker open, and allow the unit to heat for
15 minutes.
9. Apply a second layer of shortening.
10. Allow the unit to heat for 15 minutes.
11. Turn the Temperature Control completely counterclockwise
to the off position.
Operating the Unit
NOTE: Make sure to perform the “Seasoning the Waffle Plates”
procedure before the first use of the waffle maker.
Startup
1. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
2. Make sure the drip tray(s) is in position on the base of the
waffle maker.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Avoid
unnecessary contact with unit.
• Do not come in contact with waffle plates during
operation. Plates are very hot.
3. Turn the Temperature Control clockwise to the desired
temperature setting.
• Both the Power Indicator and the Heating Indicator will
illuminate.
4. Using a heat-resistant cooking brush, carefully apply an
oil-based, non-stick shortening evenly onto each waffle
plate. Make sure the shortening makes it to the bottoms of
the grooves in each plate.
NOTE: Do not leave excess shortening in the bottoms of the
groves.
Power Indicator
Temperature Control (in “off” position)
Heating Indicator
Control Panel
Form No. KWMM-0220
9
English
OPERATION
5. Close the waffle maker, and allow the unit approximately
20 minutes to reach the operating temperature.
• The Heating Indicator will go dark when the unit reaches
the selected temperature.
6. Open the waffle maker, and spread waffle batter/dough
onto the bottom/front waffle plate.
• For Brussels waffles, fill the waffle plate until the top of
the “blocks” are barely covered with batter.
• For Liège waffles, place the dough onto the waffle plate.
• For bubble waffles, fill the waffle plate until batter fills all
the holes and slightly covers the “flats” in between.
7. Close the waffle maker.
• For KWM09 models, close the top waffle plate onto the
bottom waffle plate.
KWM09 model in open position
• For KWM18 models, close the rear waffle plate onto the
front waffle plate. If cooking Brussels or bubble waffles
(liquid batter), carefully rotate both waffle plates to the
rear position for even distribution of the batter.
NOTE: Hold both handles tightly together when rotating both
waffle plates. Do not allow the plates to separate.
Rear
Waffle
Plate
Front
Waffle
Plate
Close rear plate
onto front plate.
Rotate both plates
to rear position.
Using KWM18 models
• For KWMSL models, close the top waffle plate onto the
bottom waffle plate, and carefully rotate the waffle plates
180º counterclockwise for even distribution of the batter.
Top Waffle
Plate
Bottom
Waffle
Plate
Close top plate
onto bottom plate.
Rotate/swivel
plates 180°
counterclockwise.
Using KWMSL models
8. Allow the waffle to cook for the appropriate amount of time,
determined by the batter/dough recipe. Cook time may
need to adjusted after a few trial cooking cycles.
9. Carefully open the waffle maker, and immediately remove
the waffle using a waffle pick or other appropriate utensil.
• Place waffles on a cooling rack to maintain crispness.
10. Continue to cook waffles by repeating steps 6–9 of this
procedure.
• Brush the waffle plates using just the cooking brush in
between each waffle.
• If the waffles begin sticking to the waffle plates, apply
a small amount of shortening to the plates using the
cooking brush. Use additional shortening on the plates
in between waffles as needed.
Shutdown
1. Turn the Temperature Control fully counterclockwise to the
“off” position.
2. Perform the “Daily Cleaning” procedure in the Maintenance
section of this manual.
10
Form No. KWMM-0220
English
MAINTENANCE
General
Waffle Makers are designed for maximum durability and
performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD: Allow unit to cool before performing any
cleaning, adjustments, or maintenance.
Daily Cleaning
To preserve the finish of the unit as well as maintain performance,
it is recommended that the unit be cleaned daily.
WARNING
Submerging or saturating unit with water may cause
serious injury, will damage the unit, and void unit warranty.
NOTICE
For steel surfaces, use non-abrasive cleaners and cloths
only. Abrasive cleaners and cloths could scratch finish of
unit, marring its appearance and making it susceptible to
soil accumulation.
Do not use harsh chemicals such as bleach, cleaners
containing bleach, or oven cleaners to clean this unit.
Do not attempt to cool hot waffle plates quickly, such as by
immersing in water. Damage to plates will occur.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Turn the Temperature Control fully counterclockwise to the
“off” position, unplug the power cord, and allow the unit to
cool.
2. Clean the waffle plates.
NOTE: The cast iron waffle plates are dishwasher-safe. The
“Seasoning the Waffle Plates” procedure may need to
be performed after washing the plates.
Daily:
a. Brush or wipe all food crumbs, oil, etc. from all waffle
plates into the drip tray(s).
b. Wipe the waffle plates using a clean cloth dampened in
warm water only.
Weekly (or as determined by carbon
buildup):
a. Perform the appropriate “Removing
the Waffle Plates” procedure in this section.
b. Clean each plate using a wire brush/steel scrub pad,
dish soap, and water. Rinse thoroughly with clean water.
NOTE: Eventually, waffles will start to stick due to carbon
build-up. Clean the plates thoroughly and perform the
“Seasoning the Waffle Plates” procedure. Liège waffles
that contain pearl sugar will contribute to increased
carbon buildup and will lead to more frequent plate
cleaning and re-seasoning.
3. Wipe clean all hinge pins and thumbscrews, with a non-
abrasive, damp cloth. Wipe dry with a non-abrasive, dry
cloth.
4. Remove, empty, and clean the drip tray(s).
a. Wash the drip tray with warm water and a mild detergent.
Rinse with water.
b. Allow the drip tray to air dry, or dry with a soft cloth.
5. Wipe all exterior surfaces of the unit with a non-abrasive
cloth dampened in warm water and a mild soap. Stubborn
stains may be removed with a good stainless steel cleaner.
Hard to reach areas should be cleaned with a small brush
and mild soap.
6. Rinse the unit thoroughly using a non-abrasive cloth
dampened in warm water only.
7. Dry the unit using a clean, dry, non-abrasive cloth.
8. Reinstall the drip tray(s).
9. Reinstall the waffle plates. To reinstall, reverse the
“Removing the Waffle Plates” procedure in this section.
Form No. KWMM-0220
11
English
MAINTENANCE
Removing the Waffle Plates
Non-Swivel Models
Use the following procedure to remove the waffle plates for
cleaning.
CAUTION
BURN HAZARD: Allow unit to cool before performing any
cleaning, adjustments, or maintenance .
1. Turn the Temperature Control fully counterclockwise to the
“off” position, unplug the power cord, and allow the unit to
cool.
2. For KWM18 models, rotate both waffle plates to the front
position.
3. Remove the top/rear heating element assembly.
a. Remove the two thumbscrews on the cover of the top/
rear heating element assembly.
b. Lift the top/rear heating element assembly off of the top/
rear waffle plate and set aside. The power coil still will
be attached between the element assembly and the
base of the unit.
Thumbscrew
Power
Coil
Top Heating
Element
Assembly
Top Waffle
Plate
Removing Thumbscrews and the Top/Rear Heating Element
Assembly (KWM09 model shown)
4. Remove the bottom/front heating element assembly.
For KWM09 models:
a. Holding both waffle plate handles in one hand, rotate
and hold both waffle plates up in the vertical position.
b. Flip over the drip tray and reposition on the base of the
unit.
c. Using the other hand, remove the two thumbscrews on
the cover of the bottom heating element assembly.
d. Remove the bottom heating element assembly from the
bottom waffle plate and set aside.
e. Rotate both waffle plates back down onto the flipped
drip tray.
Thumbscrew
Bottom Heating
Element
Assembly
Drip tray
flipped over.
Removing Thumbscrews and the Bottom Heating Element
Assembly—KWM09 Models
For KWM18 models:
a. Flip over the rear drip tray and reposition on the base of
the unit.
b. Rotate both waffle plates to the rear position on top of
the flipped drip tray.
c. Remove the two thumbscrews on the cover of the front
heating element assembly.
d. Lift the front heating element assembly off of the front
waffle plate and set aside.
Thumbscrew
Front Heating
Element
Assembly
Drip tray
flipped over.
Removing Thumbscrews and the Front Heating Element Assembly—
KWM18 Models
12
Form No. KWMM-0220
English
5. Remove the thumb nut from one side of the hinge pin.
6. Remove the hinge pin from the hinges on both waffle
plates. Note how the waffle plate hinges are positioned
together for reassembly.
Thumb
Nut
Hinge Pin
Rear View
Removing the Thumb Nut and Hinge Pin
(KWM09 model shown)
7. Remove the waffle plates.
Top
Waffle Plate
Bottom
Waffle Plate
Hinges
Rear View
Removing the Waffle Plates
(KWM09 model shown)
Swivel Models
Use the following procedure to remove swivel waffle plates for
cleaning.
CAUTION
BURN HAZARD: Allow unit to cool before performing any
cleaning, adjustments, or maintenance .
1. Turn the Temperature Control fully counterclockwise to the
“off” position, unplug the power cord, and allow the unit to
cool.
2. Disconnect the detachable power cord from the control box
mounted to the top waffle plate.
3. Lift the entire waffle maker off of the stand.
4. Remove the top heating element assembly.
a. Using a hex screwdriver, remove the two hex screws
from the top element cover.
Power
Cord
Hex
Screw
Washer
Top
Element
Cover
Removing the Top Element Cover
b. Lift the top element cover and control box off of the top
waffle plate and set aside. The power coils still will be
attached between the control box and both element
assemblies.
c. Remove the four, recessed Phillips-head screws from
the top heating element assembly, one on each corner.
d. Lift the top heating element assembly off of the top waffle
plate and set aside with the top element cover.
Top Heating
Element
Assembly
Top Waffle
Plate
Screw
Top Element
Cover
Top Heating
Element
Assembly
Removing the Top Heating Element Assembly
5. Flip over the waffle plates so that the bottom heating
element assembly is exposed.
MAINTENANCE
Form No. KWMM-0220
13
English
MAINTENANCE
6. Remove the bottom heating element assembly.
a. Using a hex head screwdriver, remove the two hex
screws from the bottom element cover.
Hex
Screw
Washer
Bottom
Element
Cover
Removing the Bottom Element Cover
b. Lift the bottom element cover off of the bottom waffle
plate and set aside. The power coils still will be attached
between the control box and both element assemblies.
c. Remove the four, recessed Phillips-head screws from the
bottom heating element assembly, one on each corner.
d. Lift the bottom heating element assembly off of the top
waffle plate and set aside with the bottom element cover.
Bottom
Heating
Element
Assembly
Bottom Waffle
Plate
Screw
Bottom
Element
Cover
Bottom
Heating
Element
A
ssembly
Removing the Bottom Heating Element Assembly
7. The waffle plates are now separated from the heating
elements and ready for cleaning.
14
Form No. KWMM-0220
English
Waffle Pick
A waffle pick is available as an accessories for easy removal of
cooked waffles from the waffle maker.
WAFLPICK ...... Waffle Pick
Symptom Probable Cause Corrective Action
Unit turned “On”, but no heat. Heating element(s) defective.
Contact Authorized Service Agent or Hatco for assistance.
Temperature Control defective.
Unit not hot enough. Temperature Control setting too low. Turn Temperature Control clockwise to increase the
temperature setting.
Heating element(s) defective. Contact Authorized Service Agent or Hatco for assistance.
Unit not working at all. Unit not turned on. Reviewing “Operating the Unit” in the OPERATION section
of this manual.
Unit not plugged in. Plug unit into proper power supply.
Circuit breaker tripped. Reset circuit breaker. If circuit breaker continues to trip,
contact an Authorized Service Agent or Hatco for assistance.
Temperature Control defective. Contact Authorized Service Agent or Hatco for assistance.
Waffles sticking to plates. Carbon buildup on waffle plates. Perform the “Weekly” procedure for cleaning the waffle plates
in the MAINTENANCE section, followed by the “Seasoning
the Waffle Plates” procedure in the OPERATION section.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: [email protected]
OPTIONS AND ACCESSORIES
Form No. KWMM-0220
15
English
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the “Products”)
to be free from defects in materials and workmanship, under
normal use and service, for a period of one (1) year from the
date of purchase when installed and maintained in accordance
with Hatco’s written instructions or 18 months from the date
of shipment from Hatco. Buyer must establish the Product’s
purchase date by registering the Product with Hatco or by other
means satisfactory to Hatco in its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT.
Without limiting the generality of the foregoing, SUCH
WARRANTIES DO NOT COVER: Coated incandescent light
bulbs, fluorescent lights, heat lamp bulbs, coated halogen light
bulbs, halogen heat lamp bulbs, xenon light bulbs, LED light
tubes, glass components, and fuses; Product failure in booster
tank, fin tube heat exchanger, or other water heating equipment
caused by liming, sediment buildup, chemical attack, or
freezing; or Product misuse, tampering or misapplication,
improper installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part. In
the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT
OR GOODS.
LIMITED WARRANTY
Français
16
Formulaire n° KWMM-0220
INTRODUCTION
Les gaufriers cuisent des gaufres de grande qualité en continu
pour les cuisines commerciales et les endroits où la cuisson est
effectuée sous les yeux des clients. La commande de temps et
de température ajustable permet aux utilisateurs de cuire des
gaufres de qualité en continu avec différentes sortes de pâtes.
Les ensembles d’éléments chauffants supérieur et inférieur
exclusifs et amovibles assurent une répartition exceptionnelle
de la chaleur sur l’ensemble de la surface des plaques à
gaufres. Le easy clean System
®
du gaufrier accélère le retrait
et facilite le nettoyage des plaques à gaufres.
Les gaufriers sont issus de recherches avancées et de
tests intensifs sur le terrain. Les matériaux utilisés ont été
sélectionnés afin de garantir une durée de vie maximale,
un design attractif et des performances optimales. Chaque
appareil est inspecté et testé minutieusement avant d’être
expédié.
Ce manuel fournit les instructions concernant l’installation,
la sécurité et le fonctionnement des gaufriers. Hatco vous
recommande de lire l’ensemble des instructions d’installation,
de sécurité et d’utilisation fournies dans ce manuel avant
d’installer et d’utiliser l’appareil.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Notez le numéro de modèle, le numéro de série, la tension
et la date d’achat de l’appareil dans les espaces ci-dessous
(étiquette des caractéristiques techniques située sur le dessous
de l’appareil). Veuillez avoir cette information à portée de la
main si vous appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage _________________________________________
Date d’achat _____________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
pour faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(Horaires d’été—juin à septembre:
7h00 à 17h00 du lundi au jeudi
7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
Informations Importantes pour le Propriétaire ................16
Introduction .........................................................................16
Consignes de Sécurité Importantes ................................. 17
Description du Modèle .......................................................18
Désignation du Modèle ...................................................... 19
Caractéristiques Techniques ............................................19
Configuration des fiches .................................................... 19
Tableau des valeurs nominales électriques ......................19
Dimensions ........................................................................ 20
Installation ...........................................................................21
Généralités ........................................................................21
Mode d’emploi ....................................................................22
Généralités ........................................................................22
Panneau de commande ....................................................22
Culottage des plaques à gaufres ......................................22
Fonctionnement de l’appareil ............................................22
Maintenance ........................................................................24
Généralités ........................................................................24
Nettoyage quotidien ...........................................................24
Retrait des plaques à gaufres ...........................................25
Guide de Dépannage ..........................................................28
Options et Accessoires .....................................................28
Garantie Limitée .................................................................29
Distributeurs de Pièces Autorisés ........Couverture Arrière
SOMMAIRE
Français
Formulaire n° KWMM-0220
17
CONSIGNES DE SÉCURITÉ IMPORTANTES
Lisez l’information de securite importante suivante avant d’utiliser cet équipement pour éviter
des dommages ou la mort sérieux et pour éviter d’endommager l’équipement ou la propriété.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise de courant avec terre
de tension, de format et de configuration des broches
corrects. Si la fiche et la prise ne se correspondent pas,
s’adresser à un électricien qualifié pour déterminer et
installer une prise de courant de format et de tension
corrects.
• Mettez hors tension en utilisant l’interrupteur, débranchez
le cordon d’alimentation et laissez l’unité refroidir avant
d’effectuer tout nettoyage, tout réglage ou tout entretien.
• L’appareil n’est pas résistant aux intempéries.
Placez l’appareil à l’intérieur, dans une zone dont la
température ambiante est de 40°C (104°F) maximum.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• Ne pas nettoyer l’appareil lorsqu’il est sous tension.
• Ne renversez pas de liquides dans l’appareil.
• Ne tirez pas l’unité par le cordon d’alimentation.
• Ne laissez pas le cordon pendre le long du comptoir.
• Interrompez l’utilisation de l’unité si le cordon
d’alimentation est effiloché ou usé.
• N’essayez jamais de réparer ou de remplacer un cordon
d’alimentation. Celui-ci devra être remplacé par Hatco,
un agent de service agréé par Hatco ou une personne
possédant des qualifications similaires.
• Cet appareil doit uniquement être réparé par un personnel
qualifié. Toute réparation par un personnel non qualifié
peut entraîner une électrocution et des brûlures.
• Pour les réparations, utiliser exclusivement des pièces
de rechange Hatco d’origine. Utilisez des pièces
détachées Hatco authentiques sous peine d’annuler
toutes les garanties et d’exposer l’utilisateur à des
tensions électriques dangereuses pouvant entraîner
une électrocution ou des brûlures. Les pièces
de rechange Hatco d’origine sont conçues pour
fonctionner sans danger dans les environnements
dans lesquels elles sont utilisées. Certaines pièces
de rechange génériques ou de second marché ne
présentent pas les caractéristiques leur permettant de
fonctionner sans danger dans la matériel Hatco.
RISQUE D’EXPLOSION : Ne conservez pas ou n’utilisez pas
d’essence ou d’autres vapeurs ou liquides inflammables à
proximité de ces plaques ou de tout autre appareil.
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et correcte de l’appareil.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
Ne laissez jamais l’appareil sans surveillance pendant son
utilisation.
AVERTISSEMENT
DANGER D’INCENDIE :
• Placezl’appareilàaumoins203mm(8″)desmurset
matières inflammables. Si ces distances de sécurité
ne sont pas respectées, une décoloration ou une
combustion peut se produire.
• N’obstruez pas les ouvertures de ventilation d’air sur le
boîtier extérieur de l’appareil. Cela pourrait provoquer
une combustion ou une défaillance de l’unité.
N’utilisez pas l’appareil pour des fins autres que celles qui
ont été prévues.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
ATTENTION
DANGER DE BRÛLURE :
• Certaines surfaces extérieures de l’appareil deviennent
chaudes. Toucher ces zones de l’appareil avec
précaution.
• N’entrez pas en contact avec les plaques à gaufres
pendant le fonctionnement de l’appareil. Les deux
plaques sont très chaudes.
• Laissez l’appareil refroidir avant d’effectuer tout
nettoyage, réglage ou entretien.
Placez l’appareil sur un plan de travail dont la hauteur
est appropriée, à un emplacement pratique à utiliser.
L’emplacement choisi doit être de niveau et solide afin de
supporter le poids de l’appareil et de son contenu.
AVIS
Ne placez pas l’appareil dans une zone soumise à des
températures excessives ou exposée à de la graisse
provenant de grils, poêles, etc. Des températures
excessives et la graisse risquent d’endommager l’appareil.
Les dommages à toute partie du comptoir pouvant être
causés par la chaleur générée par l’équipement de Hatco
ne sont pas couverts par la garantie de Hatco. Contactez le
fabricant du comptoir pour plus de renseignements.
En ce qui concerne les surfaces en acier, utilisez des
chiffons et produits nettoyants non abrasifs uniquement.
Les chiffons et nettoyant abrasifs pourraient rayer la
finition de l’unité, altérant son apparence et la rendant
vulnérable à l’accumulation de saleté.
L’utilisation de produits chimiques agressifs tels que l’eau
de javel, les produits nettoyants contenant de la javel, ou
les produits de nettoyage pour les fours sont proscrits
pour nettoyer l’appareil.
N’essayez pas de refroidir rapidement les plaques à
gaufres chaudes, en les immergeant dans de l’eau par
exemple. Cela endommagera les plaques.
Cet appareil est réservé à un usage professionnel
uniquement — il ne convient PAS à un usage personnel.
Nettoyez l’unité quotidiennement pour éviter les
dysfonctionnements et assurer un fonctionnement sain.
Français
18
Formulaire n° KWMM-0220
DESCRIPTION DU MODÈLE
Tous les Modèles
Les gaufriers sont composés d’un châssis en acier inoxydable
facile à nettoyer. Ces appareils comprennent des plaques à
gaufres en fonte amovibles, une ou plusieurs commandes de
température réglables avec une plage de 50 à 300°C (120
à 570°F), un témoin d’alimentation, un témoin de chauffe et
un plateau d’écoulement amovible. Des plaques à gaufres
sont disponibles pour cuisiner des gaufres de Bruxelles
(gaufresbelgesrectangulaires ou rondes), de Liège ou à bulles.
Modèles KWM09
Ces modèles sont conçus avec des plaques à gaufres
articulées de 90° et sont équipés d’un cordon d’alimentation

est conçu pour réchauffer les gaufres précuites.
Commande de la
température
Plateau
d’écoulement
Plaque à
gaufres
supérieure
Plaque à
gaufres
inférieure
Témoin d’alimentation
Témoin de chauffe
Modèles KWM09 (illustration des plaques à gaufres de Bruxelles)
Modèles KWM18
Ces modèles sont conçus avec des plaques à gaufres
articulées de 180° et sont équipés d’un cordon d’alimentation

est conçu pour préparer des gaufres avec de la pâte et pour
réchauffer les gaufres précuites.
Commande de la
température
Plateau
d’écoulement
frontal
Témoin d’alimentation
Témoin de chauffe
Plateau d’écoulement
arrière
Plaque à
gaufres
frontale
Plaque à
gaufres
arrière
Modèles KWM18
(illustration des plaques à gaufres de Bruxelles)
Modèles KWMSL
Ces modèles sont conçus avec un système pivotant qui fait
pivoter les plaques à gaufres de 180° et sont équipés d’un

Ce style de gaufrier est conçu pour cuire des gaufres à partir
de pâte liquide ou solide ainsi que pour réchauffer des gaufres
précuites.
Plateau
d’écoulement
Plaque à
gaufres
supérieure
Plaque à
gaufres
inférieure
Commande
de la
température
Témoin
d’alimentation
Témoin de chauffe
Cordon d’alimentation amovible
Modèles KWMSL
(Illustration des plaques à gaufres de Liège)
Veuillez consulter la partie OPTIONS ET ACCESSOIRES pour
connaître les éléments supplémentaires disponibles pour les
gaufriers.
Français
Formulaire n° KWMM-0220
19
Modéle Tension Puissance Intensité Configuration de Fiches Poids de l’appareil
KWM09-1BR46
120 V 1440 W 12 A NEMA 5-15P
17 kg (37 lbs.)KWM09-1LG47
KWM09-1BR46 208–240 V
†
1352–1800 W 6.5–7.5 A NEMA 6-20P
KWM18-1BR35
120 V 1440 W 12 A NEMA 5-15P
18 kg (40 lbs.)
KWM18-1BR46
208–240 V
†
1352–1800 W 6.5–7.5 A NEMA 6-20P
KWM18-1LG47
120 V 1440 W 12 A NEMA 5-15P
208–240 V
†
1352–1800 W 6.5–7.5 A NEMA 6-20P
KWM18-1RO7
120 V 1440 W 12 A NEMA 5-15P
24 kg (53 lbs.)
KWM18-1BU
KWM18-16CH 44 lbs. (20 kg)
KWM18-2BR46
208–240 V
†
2704–3600 W 13–15 A NEMA 6-20P 35 kg (78 lbs.)KWM18-2LG47
KWM18-32CH
KWMSL-4BR46
208–240 V
†
1953–2600 W 9.4–11.3 A NEMA 6-20P 31 kg (68 lbs.)
KWMSL-2LG413
CARACTÉRISTIQUES TECHNIQUES
K W M xx - x xx xx
Gaufrier
Style de gaufrier:
09 = « 90 »plaques à gaufres à charnières
18 = « 180 »plaques à gaufres à charnières
SL = plaquespivotantes de 180°
1 = Tête unique
2 = Tête double
16 = Tête unique, 16 Churros
32 = Tête double, 32 Churros
Nombre d’alvéoles de la
plaque à gaufres:
35 = Bruxelles 3 x 5
46 = Bruxelles 4 x 6
47 = Liège 4 x 7
7 = Bruxelles rondes de 7″ (17,7 cm)
413 = Liège 4 x 13
Style de plaque à gaufre:
BR = Bruxelles (belges)
RO = Bruxelles rondes
LG = Liege
BU = Bulle
CH = Churro
DÉSIGNATION DU MODÈLE
Tableau des valeurs nominales électriques
Configuration des fiches
Les appareils sont fournis par l’usine avec un cordon et une prise
électriques. Les fiches fournies correspondent à leur application.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTIQUE: Brancher l’appareil
sur une prise de courant avec terre de tension, de format
et de configuration des broches corrects. Si la fiche et la
prise ne se correspondent pas, s’adresser à un électricien
qualifié pour déterminer et installer une prise de courant
de format et de tension corrects.
NOTA: Prise non fournie par Hatco.
1(0$3
1(0$3
Configuration des fiche
† L’appareil est conçu pour fonctionner à des tensions d’alimentation comprises entre 208 et 240 volts.
Français
20
Formulaire n° KWMM-0220
Modéle
Largeur
totale (A)
Profondeur
totale (B)
Hauteur
(C)
Empattement
Largeur (D)
Empattement
Profondeur (E)
Largeur de
l’appareil (F)
Profondeur de
l’appareil (G)
KWM09-1BR46
380 mm
(15)
473 mm
(18-11/16)
232 mm
(9-1/8)
243 mm
(9-5/8)
245 mm
(9-11/16)
260 mm
(10-1/4)
315 mm
(12-7/16)
KWM09-1LG47
KWM18-1BR35
430 mm
()
589 mm
(23-3/16)
232 mm
(9-1/8)
243 mm
(9-5/8)
369 mm
(14-9/16)
260 mm
(10-1/4)
440 mm
(17-3/8)
KWM18-1BR46
KWM18-1LG47
KWM18-16CH
422 mm
()
599 mm
(23-5/8)
246 mm
(9-11/16)
372 mm
(14-11/16)
KWM18-1RO7
415 mm
()
662 mm
(26-1/16)
232 mm
(9-1/8)
243 mm
(9-5/8)
429 mm
(16-15/16)
260 mm
(10-1/4)
500 mm
(19-11/16)
KWM18-1BU
422 mm
()
599 mm
(23-5/8)
369 mm
(14-9/16)
440 mm
(17-3/8)
KWM18-2BR46
740 mm
()
599 mm
(23-5/8)
232 mm
(9-1/8)
503 mm
(19-13/16)
369 mm
(14-9/16)
520 mm
(20-1/2)
440 mm
(17-3/8)
KWM18-2LG47
KWM18-32CH
720 mm
()
506 mm
(19-15/16)
372 mm
(14-11/16)
KWMSL-4BR46
N/A
436 mm
(17-3/16)
410 mm
(16-3/16)
495 mm
(19-1/2)
323 mm
(12-3/4)
340 mm
(13-7/16)
230 mm
(9-1/16)
KWMSL-2LG413
Dimensions
C
B
G
A
F
F
D
C
C
A
D
E
B
F
B
G
E
D
E
G
Modèles
KWMSL
Modèles
KWM18
Modèles KWM09
CARACTÉRISTIQUES TECHNIQUES
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Hatco KWM Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
KWM Series
Catégorie
Gaufriers
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents