Whirlpool LTE5243DQ8 Le manuel du propriétaire

Marque: Whirlpool

Modèle: LTE5243DQ8

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

WASHER/DRYERUSERINSTRUCTIONS

INSTRUCTIONSPOURUUTILISATEUR

DELALAVEUSE/SECHEUSE

TableofContents/Tabledesmati6res

ASSISTANCE OR SERVICE ............................ 1

ACCESSORIES ................................................. 2

WASHER/DRYER SAFETY .............................. 2

WASHER USE .................................................. 6

DRYER USE ...................................................... 7

WASHER/DRYER CARE ................................. 8

TROUBLESHOOTING WASHER ................... 10

TROUBLESHOOTING DRYER ...................... 12

WARRANTY .................................................... 14

ASSISTANCE OU SERVICE ........................... 15

ACCESSOIRES ............................................... 15

SECURITE DE LA LAVEUSE/SECHEUSE ....16

UTILISATION DE LA LAVEUSE ..................... 19

UTILISATION DE LA SECHEUSE .................. 21

ENTRETIEN DE LA LAVEUSE/SECHEUSE..22

DEPANNAGE DE LA LAVEUSE ..................... 24

DEPANNAGE DE LA SECHEUSE .................. 26

GARANTIE ....................................................... 28

Para obtener acceso al manual de uso y cuidado en espa_ol, o para obtener informaci6n adicional acerca de su producto, visite:

www.whirlpool.com

Tenga listo su n0mero de modelo completo. Puede encontrar el n0mero de modelo y de serie dentro de la cavidad superior de la

puerta.

If you need assistance or service, first see the "Troubleshooting"

section. Additional help is available by calling our Customer

eXperience Center at 1-800-253-1301 from anywhere in the

U.S.A., or write:

Whirlpool Corporation

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Information may also be obtained by visiting our website at

www.whirlpool.com.

In Canada, for assistance, installation or service, call us at

1-800-807-6777, or write:

Whirlpool Canada LP

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

In Canada, visit www.whirlpool.ca.

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your appliance to help

you obtain assistance or service if you ever need it. You will need

to know your complete model number and serial number. You can

find this information on the model and serial number label, located

at the top inside dryer door well.

Dealer name

Serial number

Address

Phone number

Model number

Purchase date

Please include a daytime phone number in your correspondence.

W10196553A

Enhance your dryer with these premium accessories.

For more high-quality items or to order, call 1-800-901-2042, or visit us at www.whirlpool.com/accessories.

In Canada call 1-800-807-6777, or visit us at www.whirlpoolparts.ca.

Part Number Accessory Part Number Accessory

20-48KITRC 4 ft (1.2 m) gas line dryer connector 8212656RP 10 ft (3.0 m) Inlet hose, Black EPDM

installation kit (2 pack)

PT220L 4 ft (1.2 m) dryer cord, 3-wire, 30 amp 8212638RP 6 ft (1.8 m) Nylon braided inlet hose, space-

saving 90° elbow, hypro-blue steel

couplings. (2-pack)

PT400L 4 ft (1.2 m) dryer cord, 4-wire, 30 amp 8212487RP 5 ft (1.5 m) Nylon braided inlet hose.

(2-pack)

PT600L 6 ft (1.8 m) dryer cord, 4-wire, 30 amp 8212637RP 6 ft (1.8 m) Inlet hose, Black EPDM, space

saving 90° elbow, hypro-blue steel

couplings. (2-pack)

8212614 Dryer vent lint brush 8212545RP 5 ft (1.5 m) Inlet hose, Red and Blue EPDM.

(2-pack)

3404351 Drying rack - fits 29" (737 mm) 8212641RP 5 ft (1.5 m) Inlet hose, Black EPDM (2 pack)

Super Capacity, 6.5 cu. ft (0.18 cu. m) -

side swing or hamper door

3406839 Drying rack - fits 29" (737 mm) 8212546RP 4 ft (1.2 m) Inlet hose, Black EPDM (2 pack)

Super Capacity Plus, 7.0 cu. ft (0.20 cu. m)

- side swing door only

49971 Compact dryer stand - white 31682 All purpose appliance cleaner

49572 LP gas conversion kit 1903WH Laundry supply storage cart

This washer does not include inlet water hoses.

WASHER/DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be kiUed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - ".isk ofFire"

- Clothes dryer installation must be performed by a qualified installer.

- Install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials, if fle×ible metal

(foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Fle×ible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

= Do not try to light any appliance.

= Do not touch any electrical switch; do not use any phone in your building.

= Clear the room, building, or area of all occupants.

= Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

IM PORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

[] Read all instructions before using the washer/dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

[] Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the

washer/dryer is used near children.

[] Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer

compartments.

[] Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

[] Do not install or store the washer/dryer where it will be

exposed to the weather.

[] Do not tamper with controls.

[] Clean dryer lint screen before or after each load.

[] Under certain conditions, hydrogen gas may be produced

in a hot water system that has not been used for 2 weeks

or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the washing machine, turn on all hot water faucets and let

the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

this time.

[] Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specifically recommended in

this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" section of the Installation

Instructions booklet for grounding instructions.

SAVE THESE INSTRUCTIONS

Your dryer must be properly installed and vented to achieve

maximum drying efficiency and shorten drying times. Use the

minimum recommended installation clearances found in the

Installation Instructions. See the Installation Instructions for more

information.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

If the dryer is not properly installed and vented, it will not be

covered under the warranty. Proper venting of your dryer is

important for satisfactory drying results. See the Installation

Instructions for more detail.

NOTE: Service calls caused by improper venting will be paid for

by the customer, whether it was a paid installation or self-

installed.

Do not use plastic vent or metal foil vent. Use 4" (102 mm)

metal or flexible metal vent. Do not kink or crush flexible metal

vent. It must be completely extended to allow adequate

exhaust air to flow. Check vent after installation. Refer to the

Installation Instructions for proper length requirements of vent.

2. Use a 4" (102 mm) exhaust hood.

3. Use the straightest path possible when routing the vent.

Good Better

Use clamps to seal all joints. Do not use duct tape, screws, or

other fastening devices that extend into the interior of the vent

to secure vent, which can catch lint.

Clean exhaust vent periodically, depending on use, but at

least every 2 years, or when installing your dryer in a new

location. When cleaning is complete, be sure to follow the

Installation Instructions supplied with your dryer for final

product check.

WASHERUSE

For these suggested full-sized loads, set the LOAD SIZE selector to the highest load size setting.

LARGE CAPACITY WASHERS

Mixed Load Towels Delicates Permanent Press Knits

Heavy Work Clothes

2 pair of pants

3 shirts

3 jeans

1 coverall

2 double sheets 8 bath towels 2 camisoles 1 double sheet 2 pair of pants

4 pillowcases 8 hand towels 4 slips 1tablecloth 2 blouses

6 T-shirts 10 washcloths 6 undergarments 1 dress 4 shirts

6 pair of shorts 1 bath mat 2 sets of sleepwear 1 blouse 4 tops

2 shirts 1 child's outfit 2 pair of pants 2 dresses

2 blouses 3 shirts

6 handkerchiefs 2 pillowcases

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

Measure detergent and pour it into the washer. If desired, add

powdered or liquid color safe bleach. Drop a sorted load of

clothes loosely into your washer.

• Load evenly to maintain washer balance. Mix large and

small items. Items should move easily through the wash

water. Overloading can cause poor cleaning.

(OPTIONAL) Add liquid chlorine bleach.

Always measure liquid chlorine bleach. Do not guess. Do not

use more than 1 cup (250 mL) for a full load. Follow

manufacturer's directions for safe use. Use a cup with a

pouring spout to avoid spilling.

Let the washer fill and begin agitating the load. Add bleach to

the wash cycle so it can be removed in the rinse cycle. Pour

bleach around the agitator, not directly onto the load.

• Follow directions on the care labels. Do not use chlorine

bleach on wool, silk, spandex, acetates, or some flame-

retardant fabrics.

NOTE: Undiluted bleach will damage any fabric it touches.

The damage appears as rips, holes, tears, or color loss and

may not show up until several washings later.

(OPTIONAL) Add liquid fabric softener.

NOTE: Do not spill or drip any fabric softener onto the clothes.

Undiluted fabric softener can stain fabrics. Always dilute fabric

softener with warm water. Too much fabric softener can make

some items (diapers and towels) nonabsorbent. If this

happens, do not use it in every load, or use less of it in each

load.

Style 1: With liquid fabric softener dispenser (on some

models)

Use only liquid fabric softener in this dispenser. Pour

measured liquid fabric softener into the dispenser.

Softener is added automatically during the rinse portion

of the cycle. Dilute liquid fabric softener by filling the

dispenser with warm water until liquid reaches the

crossbar inthe dispenser opening.

Style 2: Without liquid fabric softener dispenser (on some

models)

• In the final rinse ONLY, add fabric softener that has been

diluted with V2to 1 cup (125 to 250 mL) warm water.

Close the washer lid. Washer will not agitate or spin with the

lid open.

Turn the WATER LEVEL selector to the correct setting for your

wash load and the type of fabric being washed. You may

change the load size or water level selection after the washer

has started filling by turning the selector to a different setting.

Set the TEMPERATURE selector to the correct setting for the

type of fabric and soils being washed. Use the warmest water

safe for fabric. Follow garment label instructions.

NOTE: In wash water temperatures colder than 60°F (15.6°C),

detergents do not dissolve well. Soils can be difficult to

remove. Some fabrics can retain wear wrinkles and have

increased pilling (the formation of small lint-like balls on the

surface of garments).

Push in the Cycle Control knob and turn it clockwise to the

wash cycle you want. Reduce the wash time when using a

small load size setting. Pull out the Cycle Control knob to start

the washer.

To stop or restart your washer:

• To stop the washer at any time, push in the Cycle

Control knob.

• Torestart the washer, close the lid (if open) and pull out the

Cycle Control knob.

DRYERUSE

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing}.

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils}.

items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

Before using your dryer, wipe the dryer drum with a damp cloth to

remove dust from storing and shipping.

1. Clean lint screen before each load. See "Cleaning the Lint

Screen."

2. Load clothes loosely into the dryer and close the door. Do not

pack the dryer. Allow space for clothes to tumble freely.

3. Turn the Cycle Control knob to the recommended cycle for the

type of load being dried. Use the Energy Preferred Automatic

Setting to dry most heavy to medium-weight fabrics.

4. (OPTIONAL) Your dryer may have an END OF CYCLE SIGNAL.

The signal is helpful when drying items that should be

removed from the dryer as soon as it stops. The End of Cycle

signal is part of the Start button and is selectable. Turn the

Start button to ON or OFR The signal will sound only if the

selector is set to On.

5. If desired, add fabric softener sheet. Follow package

instructions.

Stopping and Restarting

You can stop your dryer anytime during a cycle.

To stop your dryer

Open the dryer door or turn the Cycle Control knob to OFF.

NOTE: The Cycle Control knob should point to an Off area when

the dryer is not in use.

To restart your dryer

Close the door. Select a new cycle and temperature (if desired).

Press the PUSH TO START button.

6. Press the PUSH TO START button.

WASHEP RYER CARE

Keep washer/dryer area clear and free from items that would

obstruct the flow of combustion and ventilation air.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Failure to do so can result in death, explosion, or fire.

Cleaning the exterior

Use a soft, damp cloth or sponge to wipe up any spills such as

detergent or bleach. Occasionally wipe the outside of your washer

to keep it looking new.

Cleaning the interior

Clean your washer interior by mixing 1 cup (250 mL) of chlorine

bleach and enough detergent to equal twice the manufacturer's

recommended amount for a normal wash load. Pour this mixture

into your washer and run it through a complete cycle using hot

water. Repeat this process if necessary.

NOTE: Remove any hard water deposits using only cleaners

labeled as washer safe.

Cleaning the liquid fabric softener dispenser (on some

models):

1. Remove dispenser by grasping top with both hands and

squeezing, while pushing upward with thumbs.

2. Rinse dispenser under a warm water faucet, then replace it.

NOTE: Ifyour model has a liquid fabric softener dispenser, do not

wash clothes with this dispenser removed. Do not add detergent

or bleach to this dispenser; it is for liquid fabric softener only.

This washer does not include water inlet hoses. Whirlpool

Corporation recommends use of Factory Specified Parts. A list of

factory specified hoses available for separate purchase are listed

on the first page of this user instructions. These hoses are

manufactured and tested to meet Whirlpool Corporation's

specifications.

Replace water inlet hoses after 5 years of use to reduce the risk of

hose failure. Periodically inspect and replace water inlet hoses if

bulges, kinks, cuts, wear, or leaks are found.

When replacing your water inlet hoses, mark the date of

replacement on the label with a permanent marker.

,; eaxsT_}_Ssd_4}_e bc _e(£4_;

Glean the lint screen before each load. A screen blocked by lint

can increase drying time.

IMPORTANT:

• Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

• If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint.

Every Load Cleaning

Style 1:

1. The lint screen is located inside the dryer on the back wall.

Pull out the lint screen and its cover.

2. Separate the cover and the screen by squeezing the screen

and pulling on the cover at the same time.

3. Roll lint off the screen with your fingers. Do not rinse or wash

screen to remove lint. Wet lint is hard to remove.

4. Put the lint screen and cover back together and push firmly

back into place.

Style 2:

1. The lint screen is located inside the dryer in the front door well.

Pull the lint screen straight up.

2. Roll lint off the screen with your fingers. Do not rinse or wash

screen to remove lint. Wet lint is hard to remove.

3. Push the lint screen firmly back into place.

As Needed Cleaning

Laundry detergent and fabric softener residue can build up on the

lint screen. This buildup can cause longer drying times for your

clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen (as outlined following) every 6 months, or

more frequently if it becomes clogged due to a residue buildup.

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

To clean dryer drum

1. Apply a nonflammable household cleaner to the stained area

of the drum and rub with a soft cloth until stain is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not

stain future loads of clothes. Dry unstable dye items inside out to

avoid transfer of dye.

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From Inside the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

Install and store your washer/dryer where it will not freeze.

Because some water may stay in the hoses, freezing can damage

your washer/dryer. If storing or moving your washer/dryer during

freezing weather, winterize it.

Non-use or vacation care

Operate your washer/dryer only when you are at home. If you will

be on vacation or not using your washer/dryer for an extended

period of time, you should:

• Unplug washer/dryer or disconnect power.

• Turn off the water supply to the washer. This helps avoid

flooding (due to a water pressure surge) while you are away.

Towinterize washer/dryer

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.

4. Run washer on a drain and spin setting for about 30 seconds

to mix the antifreeze and water.

5. Unplug washer/dryer or disconnect power.

To use washer/dryer again

1. Flush water pipes and hoses.

2. Reconnect water inlet hoses.

3. Turn on both water faucets.

In the U.S.A.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

In Canada

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

• Plug in washer/dryer or reconnect power.

4. Run the washer through a complete cycle with 1 cup (250 mL)

of detergent to clean out antifreeze.

To transport the washer/dryer

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. If washer/dryer will be moved during freezing weather, put in a

qt (1 L) of R.V.-type antifreeze in the basket. Run washer on a

spin setting for about 30 seconds to mix the antifreeze and

water.

4. Disconnect the drain from the drain system.

5. Unplug washer/dryer or disconnect power. Disconnect wiring

if washer/dryer is direct wired.

6. Disconnect the exhaust vent.

7. Wash lint screen.

8. Make sure leveling legs are secure.

9. Place the inlet hoses into the basket.

10. Drape the power cord and drain hose over edge and into the

basket.

11. Use masking tape to secure the washer lid and dryer door.

Reinstalling your washer/dryer

1. Follow the "Installation Instructions" to locate, level, and

connect the washer/dryer.

2. Run the washer through a complete cycle with 1 scoop or

capful of detergent to clean the washer and remove the

antifreeze, if used.

• Plug inwasher/dryer or reconnect power.

TROUBLESHOOTINGWASHER

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call...

In U.S.A. www.whirlpool.com/help - In Canada www.whirlpool.ca

Noisy, vibrating, off-balance

• Is the floor flexing, sagging, or not level? Flooring that

flexes or is uneven can contribute to noise and vibration of the

washer. A 3A"(19 mm) piece of plywood under the washer will

reduce the sounds. See the Installation Instructions.

• Is the washer/dryer level? The washer/dryer must be level.

See the Installation Instructions.

Is the load balanced? Evenly distribute the load inthe

washer basket and make sure the height of the load does not

exceed the top row of basket holes.

Did you completely remove the yellow shipping strap with

cotter pins? See the Installation Instructions.

Are the gears engaging after the drain and before spin, or

is the upper part of agitator clicking during wash? These

are normal washer noises.

Is the washer gurgling or humming? When the washer

drains, the pump will make a continuous humming with

periodic gurgling or surging sounds as the final amounts of

water are removed. This is normal.

• The washer basket moves while washing. This isnormal.

Leaking

• Are the fill hoses tight?

• Are the fill hose gaskets properly seated? Check both ends

of each hose. See the Installation Instructions.

Is the drain hose properly installed? The drain hose should

be secured to the drainpipe or laundry tub. See the Installation

Instructions.

Is the sink or drain clogged? Sink and drainpipe must be

able to carry away 17 gal. (64 L) of water per minute. If sink or

drainpipe is clogged or slow, water can back up out of

drainpipe or sink. Check household plumbing (laundry tubs,

faucets, drainpipe, water pipes) for leaks.

Is water splashing off the tub ring? Center the tub before

starting the washer.

Is water splashing off the load? Evenly distribute the load in

the washer basket and make sure the height of the load does

not exceed the top row of basket holes. The fill or spray rinses

can splash off the load.

Dispenser clogged (on some models)

Did you follow the manufacturer's directions when adding

fabric softener to the dispenser (on some models)?

Measure fabric softener and slowly pour into the dispenser.

Wipe up all spills. Dilute fabric softener in the fabric softener

dispenser.

Washer won't run, fill, rinse, or agitate; washer stops

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Is the power cord plugged into a grounded 3 prong outlet?

Plug power cord into a grounded 3 prong outlet.

Are you using an extension cord? Do not use an extension

cord.

Is the indicator on the Cycle Control knob properly lined

up with a cycle? Turn the Cycle Control knob to the right

slightly and pull to start.

Are the water inlet valve screens clogged? Turn off the

water and remove inlet hoses from the washer. Remove any

accumulated film or particles. Reinstall hoses, turn on water,

and check for leaks.

Are both the hot and cold water faucets turned on? Turn

on the water.

Is the water inlet hose kinked? Straighten the hoses.

Does the water level seem too low, or does the washer

appear to not fill completely? The top of the agitator is much

higher than the highest water level. This is normal and

necessary for clothes to move freely.

Has a household fuse blown, or has a circuit breaker

tripped? Replace the fuse, or reset the circuit breaker. If the

problem continues, call an electrician.

Is the washer in a normal pause in the cycle? The washer

pauses for about 2 minutes during certain cycles. Allow the

cycle to continue. Some cycles feature periods of agitation

and soak.

Is the washer overloaded? Wash smaller loads.

Is the lid open? The lid must be closed during operation.

Washer will not agitate or spin with the lid open.

Washer continues to fill or drain; cycle seems stuck

Is the top of drain hose lower than the control knobs on

washer? The top of the drain hose must be at least

39" (990 mm) above the floor. See the Installation Instructions.

Does the drain hose fit too tightly in the standpipe, or is it

taped to the standpipe? The drain hose should be loose yet

fit securely. Do not seal the drain hose with tape. The hose

needs an air gap. See the Installation Instructions.

Washer won't drain or spin; water remains in washer

Is the drain hose clogged, or the end of the drain hose

more than 96" (2440 mm) above the floor? See the

Installation Instructions.

Is the lid open? The lid must be closed during operation.

Washer will not agitate or spin with the lid open.

Is there excessive sudsing? Always measure detergent.

Follow manufacturer's directions. If you have very soft water,

you might need to use less detergent.

Wash/Rinse temperature

Are the hot and cold water inlet hoses reversed? See

"Connect Inlet Hoses" in the Installation Instructions.

Are you washing many loads? As your frequency of loads

washed increases, the water temperature may decrease for

hot and warm temperatures. This is normal.

Load too wet

Did you use the right cycle for the load being washed?

Select a cycle with a higher spin speed (if available).

Did you wash an extra-large load? A large unbalanced load

could result in a reduced spin speed and wet clothes at the

end of the cycle. Evenly distribute the load and make sure the

height of the load does not exceed the top row of basket

holes.

Residue or lint on load

Did you sort properly? Sort lint givers (towels, chenille) from

lint takers (corduroy, synthetics). Also sort by color.

Did you overload the washer? The wash load must be

balanced and not overloaded. Clothes should move freely.

Lint or powdered detergent can be trapped in the load if

overloaded. Wash smaller loads.

Did you select the correct water level? The water level

should be correct for the load size. The load should be under

water.

Did you use enough detergent? Follow manufacturer's

directions. Use enough detergent to hold the lint in the water.

Did you line dry your clothing? If so, you can expect some

lint on the clothing. The air movement and tumbling of a dryer

removes lint from the load.

Was paper or tissue left in the pockets?

Is your water colder than 60°F (15.6°0)? Wash water colder

than 60°F (15.6°C) may not completely dissolve the detergent.

Did you use the proper cycle time and agitation speed for

the load? Reducing wash time (duration) and agitation speed

are ways to reduce lint.

Load iswrinkled, twisted, or tangled

Did you unload the washer promptly? Unload the washer as

soon as it stops.

Did you use the right cycle for the load being washed?

Use cycles with shorter wash times and low wash and spin

speeds (if available) to reduce wrinkling, tangling, and twisting.

Did you overload the washer? The wash load must be

balanced and not overloaded. Loads should move freely

during washing to reduce wrinkling, tangling, and twisting.

Was the wash water warm enough to relax wrinkles? If

safe for the load, use warm or hot wash water. Use cold rinse

water.

Are the hot and cold water hoses reversed? Check that the

hot and cold water hoses are connected to the right faucets. A

hot rinse followed by spin will cause wrinkling. See the

Installation Instructions.

• Did you wrap items around the agitator? Drop items loosely

into the washer. Do not wrap items around the agitator.

Stains, gray whites, dingy colors

Did you properly sort the load? Transfer of dye can occur

when mixing whites and colors in a load. Sort dark clothes

from whites and lights.

Was the wash temperature too low? Use hot or warm

washes if safe for the load. Make sure your hot water system

is adequate to provide a hot water wash.

Did you use enough detergent, or do you have hard

water? Use more detergent for washing heavy soils in cold or

hard water.

Are the hot and cold water hoses reversed? Check that the

hot and cold water hoses are connected to the right faucets.

See the Installation Instructions.

Did you follow the manufacturer's directions when adding

detergent and fabric softener? Measure detergent and

fabric softener. Use enough detergent to remove soil and hold

it in suspension. Dilute fabric softener and add to the rinse

portion of a cycle only. Do not drip fabric softener onto

clothes.

Is there above average iron (rust) in water? You may need

to install an iron filter.

Garments damaged

Were sharp items removed from pockets before washing?

Empty pockets, zip zippers, snap, or hook fasteners before

washing to avoid snagging and tearing of load.

Were strings and sashes tied to avoid tangling? Straps and

strings can easily become entangled in the load, causing

strain on seams and tearing.

Were items damaged before washing? Mend rips and

broken threads in seams before washing.

Did you overload the washer? The wash load must be

balanced and not overloaded. Loads should move freely

during washing.

Did you add chlorine bleach properly? Do not pour chlorine

bleach directly onto load. Wipe up bleach spills. Undiluted

bleach will damage fabrics. Do not place load items on top of

the bleach dispenser when loading and unloading the washer

(on some models). Do not use more than the manufacturer's

recommended amount for a full load.

• Did you follow the manufacturer's care label instructions?

TROUBLESHOOTINGDRYER

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call...

In U.S.A. www.whirlpool.com/help - In Canada www.whirlpool.ca.

Dryer will not run

Has a household fuse blown, or has a circuit breaker

tripped? There may be 2 fuses or circuit breakers for the

dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. Replace the fuse or reset the

circuit breaker. If the problem continues, call an electrician.

Is the correct power supply available? Electric dryers

require 240 volt power supply. Check with a qualified

electrician.

• Was a regular fuse used? Use a time-delay fuse.

• Is the dryer door firmly closed?

• Was the PUSH TO START dryer button firmly pressed?

No heat

Has a household fuse blown, or has a circuit breaker

tripped? The drum may be turning, but you may not have

heat. Electric dryers use 2 fuses or circuit breakers. Replace

the fuse or reset the circuit breaker. If a problem continues,

call an electrician.

• For gas dryers, is the valve open on the supply line?

Unusualsounds

Has the dryer had a period of non-use? If the dryer hasn't

been used for a while, there may be a thumping sound during

the first few minutes of operation.

Is a coin, button, or paper clip caught between the drum

and front or rear of the dryer? Check the front and rear

edges of the drum for small objects. Clean out pockets before

laundering.

Is it a gas dryer? The gas valve clicking is a normal operating

sound.

Are the four legs installed, and is the dryer level front to

back and side to side? The dryer may vibrate if not properly

installed. See the Installation Instructions.

Is the clothing knotted, or balled up? When balled up, the

load will bounce, causing the dryer to vibrate. Separate the

load items and restart the dryer.

Timer does not noticeably advance

• Is the dryer set to Timed or Air Dry?

The timer moves slowly and continuously for the timed

setting.

• Is the dryer set to Automatic Drying?

The timer moves only when the clothing is mostly dry.

Clothes are not drying satisfactorily, drying times are too long,

or load is too hot

• Is the lint screen clogged with lint? Lint screen should be

cleaned before each load.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

Is the exhaust vent or outside exhaust hood clogged with

lint, restricting air movement? Run the dryer for

5-10 minutes. Hold your hand under the outside exhaust hood

to check air movement. Ifyou do not feel air movement, clean

exhaust system of lint or replace exhaust vent with heavy

metal or flexible metal vent. See the Installation Instructions.

Are fabric softener sheets blocking the grille? Use only one

fabric softener sheet, and use it only once.

Is the exhaust vent the correct length? Check that the

exhaust vent is not too long or has too many turns. Long

venting will increase drying times. See the Installation

Instructions.

• Is the exhaust vent diameter the correct size? Use

4" (102 ram) diameter vent material.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 ram) above the floor

for a garage instaflation.

Failure to do so can result in death, explosion, or fire.

• Is the dryer located in a room with temperature below

45°F (7°0)? Proper operation of dryer cycles requires

o o

temperatures above 45 F (7 C).

Loads are wrinkled

Is the dryer located in a closet? Closet doors must have

ventilation openings at the top and bottom of the door. A

minimum of 1" (25 mm) of airspace is recommended for the

front of the dryer, and, for most installations, the rear of the

dryer requires 5" (127 mm). See the Installation Instructions.

Has an air dry cycle been selected? Select the right cycle

for the types of garments being dried.

Is the load too large and heavy to dry quickly? Separate the

load to tumble freely.

Lint on load

• Is the lint screen clogged? Lint screen should be cleaned

before each load.

Stains on load or drum

Was dryer fabric softener properly used? Add dryer fabric

softener sheets at the beginning of the cycle. Fabric softener

sheets added to a partially dried load can stain your garments.

Drum stains are caused by dyes in clothing (usually blue

jeans). This will not transfer to other clothing.

• Was the load removed from dryer at the end of the cycle?

• Was the dryer overloaded? Dry smaller loads that can

tumble freely.

Odors

Have you recently been painting, staining, or varnishing in

the area where your dryer is located? If so, ventilate the

area. When the odors or fumes are gone from the area, rewash

and dry the clothing.

Is the electric dryer being used for the first time? The new

electric heating element may have an odor. The odor will be

gone after the first cycle.

WHIRLPOOLCORPORATIONLAUNDRYWARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be

provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies

only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain

service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool's published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the

problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling

Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 7/08

Replacement parts

If you need to order replacement parts, we recommend that you

only use FSP_ Factory Specified Parts. These parts will fit right

and work right because they are made with the same precision

used to build every new WHIRLPOOL _ appliance.

To locate FSP_ replacement parts in your area:

Call the Customer eXperience Center at 1-800-253-1301, or your

nearest designated service center. In Canada call 1-800-807-6777.

For information on how to contact Whirlpool, please see front

page of this document.

INSTRUCTIONSD TILISATIONDELALAVEUSESECHEUSE

Si vous avez besoin d'assistance ou de service, consulter d'abord

la section "Depannage". On peut obtenir de I'aide supplementaire

en tel6phonant au 1-800-807-6777, ou en ecrivant a :

Whirlpool Canada LP

Centre d'interaction avec la clientele

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Dans votre correspondance, veuillez indiquer un numero de

tel6phone oQ I'on peut vous joindre dans la journee.

Des informations peuvent egalement _tre obtenues en visitant

notre site web www.whirlpool.ca.

Conservez ce manuel et votre re<;ude vente ensemble pour

r_f_rence ult_rieure. Pour le service sous garantie, vous

devez presenter un document prouvant la date d'achat ou

d'installation.

Inscrivez les renseignements suivants au sujet de votre appareil

menager pour mieux vous aider a obtenir assistance ou service en

cas de besoin. Vous devrez connaftre le numero de modele et le

numero de serie au complet. Cette information est donnee sur la

plaque signaletique indiquant les numeros de modele et de serie,

situee dans le Iogement superieur de la porte a I'interieur de la

secheuse.

Nom du marchand

Num_ro de s_rie

Adresse

Num_ro de t_l_phone

Num_ro de modele

Date d'achat

Vous pouvez faciliter I'utilisation de votre laveuse avec ces accessoires de premiere qualite.

Pour d'autres articles de qualite ou pour commander, composer le 1-800-901-2042 ou visiter notre site Web sur

www.whirlpool.com/accessories. Au Canada, composer le 1-800-807-6777 ou visiter notre site Web sur www.whirlpoolparts.ca.

Num_ro de pibce Accessoire Num_ro de pibce Accessoire

20-48KITRC Connecteur 4 pi (1,2 m) pour secheuse a 8212656RP Tuyau d'arrivee d'eau - EPDM noir de

gaz - ensemble d'installation 10 pi (3 m) (Lot de 2)

PT220L Cordon d'alimentation, 3 conducteurs 8212638RP Tuyau d'arrivee de 6 pi (1,8 m) en nylon

30 A, 4 pi (1,2 m) pour secheuse tresse, coude compact a 90 °, raccords

hypro-blue en acier. (lot de 2)

PT400L Cordon d'alimentation, 4 conducteurs 8212487RP Tuyau d'arrivee d'eau de 5 pi (1,5 m)

30 A, 4 pi (1,2 m) pour secheuse en nylon tresse. (Lot de 2)

PT600L Cordon d'alimentation, 4 conducteurs 8212637RP Tuyau d'arrivee d'eau - EPDM noir de

30 A, 6 pi (1,8 m) pour secheuse 6 pi (1,8 m) coude compact de 90°, raccord

acier hypro-blue. (Lot de 2)

8212614 Brosse a peluches pour conduit 8212545RP Tuyau d'arrivee d'eau - EPDM rouge et bleu

d'evacuation de secheuse de 5 pi (1,5 m). (Lot de 2)

3404351 Grille de sechage pour appareil grande 8212641RP Tuyau d'arrivee d'eau - EPDM noir de

capacite 29" (73,7 cm), 6,5 pi3 (0,18 m3)- 5 pi (1,5 m) (Lot de 2)

porte a ouverture laterale ou verticale

3406839 Grille de sechage pour appareil grande 8212546RP Tuyau d'arrivee d'eau - EPDM noir de

capacite 29" (73,7 cm), 7,0 pP (0,20 m_) 4 pi (1,2 m) (Lot de 2)

porte a ouverture laterale seulement

49971 Piedestal compact pour secheuse - blanc 31682 Produit de nettoyage polyvalent pour

appareils menagers

49572 Ensemble de conversion pour gaz propane 1903WH Casier de rangement de fournitures de

buanderie

Les tuyaux d'arrivee d'eau ne sont pas inclus avec cette laveuse.

P P P

SECURITEDELALAVEUSE/SECHEUSE

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de s6curit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours lire tousles messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit6.

Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de d6ces et de blessures graves a vous

eta d'autres.

Tousles messages de s6curit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c_s ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d6c_s ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

AVERTISSEMENT - "Risque d'incendie"

- L'installation de la s_cheuse & linge dolt _tre effectu_e par un installateur qualifi_.

- installer la s_cheuse conforrn_rnent aux instructions du fabricant et au× codes Iocaux.

- Ne pas installer de s_cheuse & linge avec des mat_riau× d'_vacuation en plastique

souple. Si un conduit rn_tallique souple (de type papier d'aluminiurn) est installS,

celui-ci doit _tre d'un type sp_cifique identifi_ par le fabricant de I'appareil et

convenir _ une utilisation avec les s_cheuses _ linge. Les rnat_riau× d'_vacuation

souples sont connus pour s'affaisser, Ctre facilement _cras_s et bloquer la charpie.

Ces situations obstrueront le d_bit d'air de la s_cheuse & linge et augmenteront le

risque d'incendie.

- Pour r6duire le risque de blessure grave ou de d6c_s, suivre toutes

ies instructions d'installation.

- Conserver ces instructions.

AVERTISSEiVlENT: Pour votre securite, les renseignements dans ce manuel doivent

_tre observ6s pour reduire au minimum les risques d'incendie ou d'explosion ou pour

eviter des dommages au produit, des blessures ou un deces.

- Ne pas entreposer ou utiliser de I'essence ou d'autres vapeurs ou liquides

inflammables b proximit6 de cet appareil ou de tout autre appareil 61ectrom6nager.

-QUE FAIRE DANS LE CAS D'UNE ODEUR DE GAZ :

• Ne pas tenter d'allumer un appareil.

® Ne pas toucher a un commutateur 61ectrique; ne pas utiliser le t_16phone se trouvant

sur les lieux.

® Evacuer tousles gens de la piece, de I'_difice ou du quarrier.

®Appeler imm_diatement le fournisseur de gaz du t_l_phone d'un voisin. Suivre ses

instructions.

= A d_faut de joindre votre fournisseur de gaz, appeler les pompiers.

- L'installation et I'entretien doivent _tre effectu_s par un installateur qualifi6, une

agence de service ou le fournisseur de gaz.

AVERTISSEMENT : L'odorat ne permet pas toujours la detection d'une fuite de gaz.

Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).

Pour d'autre information, contacter le fournisseur de gaz local.

En cas de detection d'une fuite de gaz, executer les instructions "Que faire dans le cas d'une odeur de gaz".

(MPORTANTES INSTRUCTIONS DE Si_CUR(T[ =

AME[::{T_SSE[_M_EN'r • Pour r6duire les risques d'incendie, de choc 61ectrique ou de blessures Iors de I'utilisation de

la laveuse/s6cheuse, suivre les pr6cautions fondamentales dont les suivantes :

m Lire toutes les instructions avant d'utiliser la

laveuse/s6cheuse.

m Ne pas placer des articles expos6s aux huiles de cuisson

dans votre s6cheuse. Les articles contamin6s par des huiles

de cuisson peuvent contribuer &une r6action chimique qui

pourrait causer & la charge de s'enflammer.

m Ne pas faire laver ou s6cher des articles qui ont 6t6 nettoy6s

ou laves avec de I'essence ou imbib6s d'essence, solvants

de nettoyage a sec, ou autres substances inflammables ou

explosives; ces substances peuvent 6mettre des vapeurs

susceptibles de s'enflammer ou d'exploser.

m Ne pas ajouter d'essence, solvant de nettoyage a sec ou

autre produit inflammable ou explosif dans I'eau de lavage.

Ces substances peuvent 6mettre des vapeurs susceptibles

de s'enflammer ou d'exploser.

m Ne pas laisser des enfants jouer sur ou &I'interieur de la

laveuse/s6cheuse. Bien surveiller les enfants Iorsque la

laveuse/s6cheuse est utilis6e & proximit6 d'enfants.

m Avant de mettre la laveuse/s6cheuse au rebut ou hors de

service, enlever la porte ou le couvercle.

m Ne pas tenter d'atteindre un article & I'int6rieur de la cuve de

la laveuse/s6cheuse Iorsque le tambour, la cuve ou

I'agitateur est en mouvement.

m Ne pas installer ou remiser cette laveuse/s6cheuse & un

endroit oQelle serait expos6e aux intemp6ries.

m Ne pas modifier les organes de commande.

m Nettoyer le filtre & charpie avant et apres chaque charge.

m Dans certaines conditions, de I'hydrogene gazeux peut se

former dans un circuit d'eau chaude qui n'a pas 6t6 utilis6

pendant 2 semaines ou plus. LE GAZ HYDROGENE EST

EXPLOSIBLE. Si le circuit d'eau chaude n'a pas 6t6 utilis6

pendant une telle p6riode, avant d'utiliser la laveuse/

s6cheuse, ouvrir tousles robinets d'eau chaude et laisser

I'eau s'6couler pendant plusieurs minutes par chaque

robinet. Ceci permettra 1'6vacuation de I'hydrogene gazeux

accumul6. Comme ce gaz est inflammable, ne pas fumer

ou utiliser une flamme nue au cours de cette p6riode.

I Ne pas reparer ou remplacer un composant quelconque de

la laveuse/s6cheuse, ni entreprendre une op6ration de

service, si ce n'est sp6cifiquement recommand6 dans ce

manuel ou dans un manuel d'instructions de r6parations

destin6 a I'utilisateur; il est alors essentiel que la personne

concernee comprenne ces instructions et soit comp6tente

pour les ex6cuter.

m Ne pas utiliser un produit assouplissant de tissu ou des

produits pour 61iminer la statique & moins qu'ils ne soient

recommand6s par le fabricant du produit assouplissant de

tissu ou du produit.

m Ne pas utiliser la chaleur pour faire secher des articles

fabriqu6s avec du caoutchouc mousse ou des mat6riaux

semblables.

m Ne pas laisser la charpie, la poussiere, ou la salet6

s'accumuler autour du systeme d'6vacuation ou autour de

I'appareil.

m Un nettoyage p6riodique de I'int6rieur de la s6cheuse et du

conduit d'6vacuation doit etre effectue par une personne

qualifiee.

m Voir "Specifications electriques" pour les instructions de

liaison & la terre.

CONSERVEZ CES INSTRUCTIONS

_7_ ¸ _ _ _ . __ _ _ _ _ _

La secheuse doit _tre bien installee et munie d'un systeme

adequat d'evacuation de I'air pour donner une efficacite maximale

de sechage et un temps de sechage plus court. Utiliser les

degagements minimums recommandes pour I'installation que

vous trouverez dans vos Instructions d'installation. Voir les

Instructions d'installation pour plus de renseignements.

Risque d'incendie

Utiliser un conduit d'_vacuation en m_tal Iourd.

Ne pas utiliser un conduit d'_vacuation en plastique.

Ne pas utiliser un conduit d'_vacuation en feuille

de m_tal.

Le non-respect de ces instructions peut causer

un d_c_s ou un incendie.

Si la secheuse n'est pas bien installee et munie d'un systeme

adequat d'evacuation de I'air, elle ne sera pas couverte en vertu

de la garantie. Pour obtenir les meilleurs resultats de sechage,

I'evacuation de I'air doit _tre adequate. Voir les Instructions

d'installation pour plus de renseignements.

REMARQUE : Les visites de service causees par une evacuation

inadequate seront aux frais du client peu importe s'il a fait faire

I'installation ou s'il I'a faite lui-m_me.

Ne pas utiliser un conduit d'evacuation en plastique ou en

feuille de metal. Utiliser un conduit de 4" (102 mm) en metal

Iourd ou flexible. Ne pas deformer ni ecraser le conduit

d'evacuation en metal flexible. II doit _tre completement

deploy6 pour permettre I'evacuation adequate de I'air. Verifier

le systeme d'evacuation apres I'installation. Se ref6rer aux

Instructions d'installation pour la bonne Iongueur du conduit

d'evacuation.

Utiliser un clapet d'evacuation de 4" (102 mm).

Utiliser I'acheminement le plus rectiligne possible Iors de

I'installation du conduit.

Bon Meilleur

Utiliser des brides pour sceller tousles joints. Ne pas utiliser

de ruban adhesif pour conduit, de vis ou d'autres dispositifs

de fixation qui se prolongent & I'interieur du conduit pour fixer

celui-ci. Ceux-ci peuvent retenir la charpie.

Nettoyer periodiquement le conduit d'evacuation, selon

I'utilisation, mais au moins tous les 2 ans ou Iors de

I'installation de la secheuse & un nouvel endroit. Apres le

nettoyage, veuillez suivre les Instructions d'installation

fournies avec la secheuse pour une verification finale de

I'appareil.

UTILISATIONDELALAVEUSE

Pour ces exemples de charges completes de la laveuse, regler le selecteur LOAD SIZE (volume de charge) au plus haut reglage de

charge.

LAVEUSE DE GRANDE CAPACITE

V6tements de Charge mixte Serviettes Articles d_licats Pressage Tricots

travail Iourds permanent

2 pantalons 2 draps doubles 8 serviettes de bain 2 chemisettes 1 drap double 2 pantalons

3 chemises 4 taies d'oreiller 8 serviettes & main 4 combinaisons- 1 nappe 2 chemisiers

3 jeans 6 tee-shirts 10 debarbouillettes jupons 1 robe 4 chemises

1 salopette 6 shorts 1 tapis de bain 6 sous-v_tements 1 chemisier 4 hauts

2 chemises 2 paires de pyjamas 2 pantalons 2 robes

2 chemisiers 1 ensemble pour 3 chemises

6 mouchoirs enfant 2 taies d'oreiller

Risque d'incendie

Ne jamais mettre des articles humect_s d'essence ou

d'autres fiuides inflammables darts la laveuse.

Aucune laveuse ne peut cornpleternent enlever I'huile.

Ne pas faire s_cher des articles qui ont _t_ salis par

tout genre d'huile (y compris les huiles de cuisson).

Le non=respect de ces instructions peut causer un

d_c_s, une explosion ou un incendie.

Style 1 : Distributeur d'assouplissant de tissu liquide (sur

certains modeles)

Utiliser seulement de I'assouplissant de tissu liquide dans

ce distributeur. Verser une quantite mesuree de

I'assouplissant de tissu liquide dans le distributeur.

L'assouplissant est ajoute automatiquement durant

I'operation de rin£;age du programme. Diluer

I'assouplissant de tissu liquide en remplissant le

distributeur d'eau tiede jusqu'& ce que le liquide atteigne

le croisillon dans I'ouverture du distributeur.

Style 2 :Absence de distributeur d'assouplissant de tissu

liquide (sur certains modeles)

• Ajouter I'assouplissant de tissu dilue avec 1/2& 1tasse

(125 &250 mL) d'eau tiede au rin(}age final SEULEMENT.

Mesurer le detergent et le verser dans la laveuse. Si desir6,

ajouter de la Javel sans danger pour les couleurs, en poudre

ou liquide. Mettre une charge de v_tements tries dans la

laveuse sans la tasser.

Charger uniformement pour maintenir I'equilibre de la

laveuse. M61anger les gros et les petits articles. Les

articles doivent pouvoir se deplacer facilement dans I'eau

de lavage. Une surcharge peut causer un pietre nettoyage.

(FACULTATIF) Ajouter I'eau de Javel liquide.

Toujours mesurer I'eau de Javel liquide. Ne pas verser une

quantite approximative. Ne jamais utiliser plus de 1 tasse (250

mL) pour une charge complete. Suivre les instructions du

fabricant pour une utilisation sans danger. Utiliser une tasse

avec un bec verseur pour eviter de renverser le liquide.

Laisser la laveuse se remplir et commencer I'agitation de la

charge. Ajouter I'eau de Javel au programme de lavage de

sorte qu'elle puisse _tre elimin6e au programme de rin£_age.

Verser I'eau de Javel autour de I'agitateur et non directement

sur la charge.

• Suivre le mode d'emploi sur les etiquettes du linge. Ne

pas utiliser d'eau de Javel sur les articles en laine, soie,

spandex, les acetates ou certains tissus ignifuges.

REMARQUE : L'eau de Javel non diluee peut endommager

tousles tissus avec lesquels elle entre en contact. IIen resulte

des deg&ts comme des dechirures, des trous, de I'usure ou

des pertes de couleur, qui peuvent ne pas paraftre avant

plusieurs lavages subsequents.

Rabattre le couvercle de la laveuse. La laveuse n'effectuera

pas d'agitation ni d'essorage avec le couvercle ouvert.

Tourner le selecteur WATER LEVEL (niveau d'eau) au bon

reglage pour votre charge de lavage et le type de tissu & laver.

Vous pouvez changer votre selection de la taille de charge et

du niveau d'eau apres que la laveuse a commence & se

remplir en tournant le bouton de selection & un reglage

different.

Regler le selecteur de TEMP#RATURE au reglage approprie

pour le type de tissu et le niveau de salete de la charge.

Utiliser I'eau la plus chaude sans danger pour le tissu. Suivre

les instructions sur I'etiquette des v_tements.

REMARQUE •Dans les temperatures d'eau de lavage

inferieures & 60°F (15,6°C), les detergents ne se diluent pas

bien. Les saletes peuvent _tre difficiles & enlever. Certains

tissus peuvent retenir les faux plis et comporter un

boulochage accru (formation de petites boules de charpie sur

la surface des v_tements).

Appuyer sur le bouton de commande de programme et le

tourner dans le sens horaire au programme que vous desirez.

Reduire le temps de lavage Iors de I'utilisation d'un reglage

pour petite charge. Tirer sur le bouton de commande de

programme pour mettre la laveuse en marche.

(FACULTATIF) Ajouter I'assouplissant de tissu liquide.

REMARQUE • Ne pas renverser ou faire degoutter

d'assouplissant de tissu sur les v_tements. Un assouplissant

de tissu non dilu_ peut causer des taches sur les tissus.

Toujours diluer I'assouplissant de tissu avec de I'eau tiede.

Une trop grande quantite d'assouplissant de tissu peut rendre

certains articles (couches et serviettes) non absorbants. Le

cas echeant, ne pas I'utiliser &chaque charge ou en utiliser

moins avec chaque charge.

Arr6t et remise en marche de la laveuse :

Pour arr_ter la laveuse &tout moment, appuyer sur le

bouton de commande de programme.

Pour remettre la laveuse en marche, rabattre le couvercle

(si ouvert) et tirer sur le bouton de commande de

programme.

La page charge ...

Whirlpool LTE5243DQ8 Le manuel du propriétaire

Marque: Whirlpool

Modèle: LTE5243DQ8

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool LTE5243DQ8 Owner's manual

Whirlpool LTE5243DQ8 Le manuel du propriétaire

Whirlpool LTE5243DQ8 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents