Sony HTCT260 Manuel utilisateur

Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur
HT-CT260/HT-CT260HP
4-431-775-13(1)
E:\HT-CT260-
re\4431775131_basedata\4431775122HTCT260UC2\00COV-
HTCT260UC2\080BCO.fm
masterpage: Left
©2012 Sony Corporation Printed in Malaysia
4-431-775-13(1)
HT-CT260/HT-CT260HP
4-431-775-13(1)
4-431-775-13(1)
HT-CT260/HT-CT260HP
E:\HT-CT260-
re\4431775131_basedata\4431775122HTCT260UC2\00COV-
HTCT260UC2\010COV.fm
masterpage: Left
Home Theatre
System
Operating Instructions US
Mode d’emploi FR
Manual de instrucciones ES
2
US
To reduce the risk of fire or
electric shock, do not expose this
apparatus to rain or moisture.
The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
To reduce the risk of fire, do not cover the
ventilation opening of the apparatus with
newspapers, tablecloths, curtains, etc.
Do not place the naked flame sources such as
lighted candles on the apparatus.
To reduce the risk of fire or electric shock, do
not expose this apparatus to dripping or
splashing, and do not place objects filled with
liquids, such as vases, on the apparatus.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main
plug from the AC outlet immediately.
Do not install the appliance in a confined
space, such as a bookcase or built-in cabinet.
Do not expose batteries or apparatus with
battery-installed to excessive heat such as
sunshine, fire or the like.
In door use only.
For the customers in the U.S.A
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the appliance.
Owner’s Record
The model and serial numbers are located on
the rear oblique down-facing surface of the
unit. Record the serial numbers in the space
provided below. Refer to them whenever you
call upon your Sony dealer regarding this
product.
M o d e l N o . H T - C T 2 6 0 / H T - C T 2 6 0 H P
Serial No.
Important Safety
Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
10) Protect the power cord from being walked
on or pinched particularly at plugs,
WARNING
3
US
convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
The following FCC statement applies only to
the version of this model manufactured for
sale in the U.S.A. Other versions may not
comply with FCC technical regulations.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
For the Sound Bar (SA-CT260)
The nameplate and the date of manufacture
marking are located on the rear oblique down-
facing surface.
For the Sound Bar (SA-CT260)
For the wireless transceiver
(EZW-RT50)
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This equipment must not be co-located or
operated in conjunction with any other
antenna or transmitter.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio
frequency (RF) Exposure Guidelines in
Supplement C to OET65. This equipment
should be installed and operated keeping the
radiator at least 20cm or more away from
person’s body (excluding extremities: hands,
wrists, feet and ankles).
continued
4
US
For the customers in the Canada
For the Sound Bar (SA-CT260)
For the wireless transceiver
(EZW-RT50)
This Class B digital apparatus complies with
Canadian ICES-003.
Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause
undesired operation of the device.
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment and meets the RSS-102 of the IC
radio frequency (RF) Exposure rules.
This equipment should be installed and
operated keeping the radiator at least 20 cm or
more away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
5
US
Precautions
On safety
• Should any solid object or liquid fall into the
system, unplug the system and have it
checked by qualified personnel before
operating it any further.
• Do not climb on the Sound Bar or the
subwoofer, as you may fall down and injure
yourself, or system damage may result.
On power sources
• Before operating the system, check that the
operating voltage is identical to your local
power supply. The operating voltage is
indicated on the nameplate at the rear of the
Sound Bar.
• If you are not going to use the system for a
long time, be sure to disconnect the system
from the wall outlet (mains). To disconnect
the AC power cord (mains lead), grasp the
plug itself; never pull the cord.
• One blade of the plug is wider than the other
for the purpose of safety and will fit into the
wall outlet (mains) only one way. If you are
unable to insert the plug fully into the outlet,
contact your dealer.
• AC power cord (mains lead) must be
changed only at the qualified service shop.
On heat buildup
Although the system heats up during
operation, this is not a malfunction. If you
continuously use this system at a large
volume, the system temperature of the back
and bottom rises considerably. To avoid
burning yourself, do not touch the system.
On placement
• Place the system in a location with adequate
ventilation to prevent heat buildup and
prolong the life of the system.
• Do not place the system near heat sources, or
in a place subject to direct sunlight,
excessive dust, or mechanical shock.
• Do not place anything at the rear of the
Sound Bar that might block the ventilation
holes and cause malfunctions.
• If the system is being used in combination
with a TV, VCR, or tape deck, noise may
result, and picture quality may suffer. In this
case, place the system away from the TV,
VCR, or tape deck.
• Use caution when placing the system on
surfaces that have been specially treated
(with wax, oil, polish, etc.) as staining or
discoloration of the surface may result.
• Take care to avoid any possible injury on the
corners of the Sound Bar or the subwoofer.
On operation
Before connecting other equipment, be sure to
turn off and unplug the system.
If you encounter color
irregularity on a nearby TV
screen
Color irregularities may be observed on
certain types of TV sets.
If color irregularity is
observed...
Turn off the TV set, then turn it on again after
15 to 30 minutes.
If color irregularity is
observed again...
Place the system further away from the TV
set.
On cleaning
Clean the system with a soft dry cloth. Do not
use any type of abrasive pad, scouring powder
or solvent such as alcohol or benzine.
If you have any question or problem
concerning your system, please consult your
nearest Sony dealer.
continued
6
US
This model incorporates Dolby* Digital and
Pro Logic Sound and the DTS** Digital
Surround System.
* Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D
symbol are trademarks of Dolby
Laboratories.
** Manufactured under license under U.S.
Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide
patents issued & pending. DTS, the
Symbol, & DTS and the Symbol together
are registered trademarks & DTS Digital
Surround and the DTS logos are
trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights
Reserved.
The Bluetooth
®
word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Sony
Corporation is under license.
Other trademarks and trade names are those of
their respective owners.
Bluetooth wireless
technology
Bluetooth wireless technology is a short-
range wireless technology linking digital
devices, such as personal computers and
digital cameras. Using the Bluetooth
wireless technology, you can operate the
units involved within a range of about 10
meters.
The Bluetooth wireless technology is
commonly used between two devices,
but a single device can be connected to
multiple devices.
You do not need wires to get connected
as you do with a USB connection, and
you do not need to place the devices face
to face as you do with wireless infrared
technology. You can use the technology
with one Bluetooth device in your bag or
pocket.
Bluetooth wireless technology is a global
standard supported by thousands of
companies. These companies produce
products that meet the global standard.
Supported Bluetooth
version and profiles
Profile refers to a standard set of
capabilities for various Bluetooth
product capabilities. This system
supports the following Bluetooth version
and profiles.
Supported Bluetooth version:
Bluetooth Standard version 2.1 + EDR
(Enhanced Data Rate)
Supported Bluetooth profiles:
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote Control
Profile)
Copyrights
7
US
For you to use the Bluetooth function,
the Bluetooth device to be connected
must support the same profile as this
system. Even if the device supports the
same profile, the functions may differ
because of the specifications of the
Bluetooth device.
The audio playback on this system may
be delayed from that on the Bluetooth
device because of the characteristics of
the Bluetooth wireless technology.
Effective communication
range
Bluetooth devices should be used within
approximately 10 meters (33 feet)
(unobstructed distance) of each other.
The effective communication range may
become shorter under the following
conditions.
When a person, metal object, wall or
other obstruction is between the
devices with a Bluetooth connection
Locations where a wireless LAN is
installed
Around microwave ovens that are in
use
Locations where other electromagnetic
waves occur
Effects of other devices
Bluetooth
devices and wireless LAN
(IEEE 802.11b/g) use the same frequency
band (2.4 GHz). When using your
Bluetooth
device near a device with
wireless LAN capability, electromagnetic
interference may occur.
This could result in lower data transfer
rates, noise, or inability to connect. If
this happens, try the following remedies:
Try connecting this system and
Bluetooth mobile phone or Bluetooth
device when you are at least 10 meters
(33 feet) away from the wireless LAN
equipment.
Turn off the power to the wireless LAN
equipment when using your Bluetooth
device within 10 meters.
Effects on other devices
The radio waves broadcast by this
system may interfere with the operation
of some medical devices. Since this
interference may result in malfunction,
always turn off the power on this system,
Bluetooth mobile phone and Bluetooth
device in the following locations:
In hospitals, on trains, in airplanes, at
gas stations, and any place where
flammable gasses may be present
Near automatic doors or fire alarms
• This system supports security functions that
comply with the Bluetooth specification as a
means of ensuring security during
communication using Bluetooth technology.
However, this security may be insufficient
depending on the setting contents and other
factors, so always be careful when
performing communication using Bluetooth
technology.
• Sony cannot be held liable in any way for
damages or other loss resulting from
information leaks during communication
using Bluetooth technology.
Bluetooth communication is not necessarily
guaranteed with all Bluetooth devices that
have the same profile as this system.
Bluetooth devices connected with this
system must comply with the Bluetooth
specification prescribed by the Bluetooth
SIG, Inc., and must be certified to comply.
However, even when a device complies with
the Bluetooth specification, there may be
cases where the characteristics or
specifications of the Bluetooth device make
it impossible to connect, or may result in
Notes
Notes
continued
8
US
different control methods, display or
operation.
• Noise may occur or the audio may cut off
depending on the Bluetooth device
connected with this system, the
communications environment, or
surrounding conditions.
9
US
Precautions .................................... 5
Bluetooth wireless technology ...... 6
Getting Started
Unpacking ................................... 10
Index to parts and controls .......... 12
Installing the supplied wireless
transceivers ........................... 16
Connecting the TV and player,
etc. ........................................ 18
Positioning the system ................ 19
Connecting the AC power cord
(mains lead) .......................... 22
Setting up the Wireless
System .................................. 22
Setting up the sound output of the
connected equipment ............ 23
Playback Options
Operating the system using the
supplied remote control ........ 24
Bluetooth Function
Using the Bluetooth function ...... 25
Surround Function
Enjoying the surround effect ...... 29
Advanced Settings
Controlling connected equipment
with the remote control ......... 30
Setting manufacturer of
controllable TVs ................... 31
Settings and adjustments using
the amplifier menu ................ 33
Additional Information
Troubleshooting .......................... 38
Specifications .............................. 40
Index ........................................... 43
Table of contents
10
US
Unpacking
Subwoofer (SA-WCT260) (1)
Sound Bar (SA-CT260) (1)
Wireless transceivers (EZW-RT50) (2)
Digital optical cord for a TV (1)
Remote control (RM-ANP084) (1)
R6 (size AA) batteries (2)
Operating Instructions (1)
Warranty (1)
Getting Started
HT-CT260HP only.
NOT supplied with the HT-CT260.
Digital coaxial cord (1) Analog audio cord (1)
11
US
Getting Started
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the
batteries to the diagram inside the battery compartment of the remote control. To use
the remote control, point it at the remote control sensor at the front of the Sound
Bar.
• Do not leave the remote control in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote control casing, particularly when replacing the
batteries.
• Do not expose the remote control sensor to direct sunlight or lighting apparatus. Doing so may
cause a malfunction.
If you do not intend to use the remote control for an extended period of time, remove the batteries
to avoid possible damage from battery leakage and corrosion.
Inserting batteries into the remote control
Notes
12
US
Index to parts and controls
For more information, see the pages indicated in parentheses.
A ?/1 (on/standby)
B (remote control sensor)
C (Bluetooth) touch key/
indicator
D INPUT touch key
Press to select the input source to
play back.
Every time you press the key, the
input source changes cyclically as
follows:
OPTICAL t COAXIALt
ANALOG t BT AU t
OPTICAL
E VOL +/– touch keys
F Front panel display (page 13)
• Touch a touch key lightly with a fingertip. If
you touch two or more keys simultaneously
or touch with a thumb, appropriate operation
may not be obtained.
Sound Bar
Tip
13
US
Getting Started
A Audio format indicators
Light up according to the audio
format that is being input to the
system.
D: Dolby Digital
DTS
LPCM: Linear PCM
PL II: Lights while Dolby Pro
Logic II is active (page 29).
B NIGHT (page 35)
Lights up in NIGHT mode.
C Message display area
Displays volume, selected input
source, etc.
Front panel display (on the Sound Bar)
continued
14
US
A ?/1 (on/standby) indicator
B ?/1 (on/standby) button
C SECURE LINK button (page 36)
Subwoofer
15
US
Getting Started
This section describes subwoofer and
Sound Bar button operation. See page 30
for details on the button operation of
connected equipment.
• Point the remote control towards the remote
control sensor ( ) of the Sound Bar.
*The N and VOL + buttons have a tactile
dot. Use it as a guide during operation.
A ?/1 (on/standby)
B INPUT +/–
Press one of the buttons to select the
equipment you want to use.
C SOUND FIELD (page 29)
D DISPLAY
Press to change the display status.
Each time you press the button, ON
and OFF are toggled. The factory
setting is ON.
ON: The display is always lit.
OFF: The display is turned off.
When the system is operated, the
display is lit for several seconds.
E MUTING
F VOL +*/–
Press to adjust the volume.
G AMP MENU (page 33)
H C, X, x, c or
Press C, X, x or c to select the menu
items. Then press to enter the
selection.
I NIGHT
Each time the button is pressed,
“ON” or “OFF” is toggled. For
details on night mode, see page 35.
Remote control
Note
TV VOL TV CH
16
US
Installing the supplied wireless transceivers
Insert the two supplied wireless transceivers into the wireless transceiver
(EZW-RT50) slot on the rear panel of both the Sound Bar and the subwoofer.
1 Remove the cover for the wireless transceiver slot on the rear of the
Sound Bar.
2 Place the wireless transceiver as shown below.
Installing the wireless transceiver on the Sound Bar
Wireless transceiver
17
US
Getting Started
3 Push in the wireless transceiver to the slot until it stops.
4 Attach the cover as it was.
Installing the wireless transceiver to the subwoofer
Wireless transceiver
18
US
Connecting the TV and player, etc.
TV
Analog audio
cord
*
(not supplied)
DVD player, etc.
Analog audio
output
Optical digital
audio output
Digital coaxial cord
*
(not supplied)
Digital optical
cord (supplied)
Digital coaxial
audio output
* Supplied with the HT-CT260HP only.
Smartphone,
“Walkman”, etc.
19
US
Getting Started
Positioning the system
The illustrations below are examples of how to install the Sound Bar.
When you select a place for the Sound Bar or the subwoofer, do not block the heat ventilation
on the rear panel of the Sound Bar or the subwoofer.
Note on installing the Sound Bar in front of a TV
When the Sound Bar is placed in front of a TV, the TV may not be controlled with the
remote control of the TV. In that case, place the Sound Bar away from the TV.
If the remote control of the TV still cannot control the TV, set IR REP. of the AMP
menu to ON (page 35).
• Be sure to confirm that the remote control of the TV cannot control the TV, then set IR REP. to
ON. If it is set to ON when the remote control can control the TV, appropriate operation may not
be obtained, because of the interference between the direct command from the remote control
and the command via the Sound Bar.
Note
Installing the Sound Bar
Installing the Sound Bar on a rack Installing the Sound Bar on a wall
(page 20)
Note
continued
20
US
When the Sound Bar is to be placed
facing upward slightly or on a wall,
remove the two stands at the bottom of
the Sound Bar, as shown below.
You can install the Sound Bar on the
wall.
• Use screws that are suitable for the wall
material and strength. As a plaster board wall
is especially fragile, attach the screws
securely to a wall beam. Install the Sound
Bar on a vertical and flat reinforced area of
the wall.
• Be sure to subcontract the installation to
Sony dealers or licensed contractors and pay
special attention to safety during the
installation.
• Sony is not responsible for accidents or
damage caused by improper installation,
insufficient wall strength, improper screw
installation or natural calamity, etc.
1 Prepare screws (not supplied)
that are suitable for the holes on
the back of the Sound Bar.
2 Fasten the screws to the wall.
The screws should protrude 6 to
7 mm (approx. 1/4 inches).
Removing the stands
Installing the Sound Bar
on a wall
Notes
Stand
Hole on the back of the Sound Bar
4 mm
(3/16 inches)
more than 25 mm (1 inch)
5mm
(7/32 inches)
10 mm
(13/32 inches)
592 mm
(23 3/8 inches)
6 to 7 mm
(approx. 1/4
inches)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130

Sony HTCT260 Manuel utilisateur

Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur

dans d''autres langues