Clarity Cordless Telephone W425 Manuel utilisateur

Walker Ameriphone

A Division of Plantronics, Inc.

4289 Bonny Oaks Drive, Suite 106

Chattanooga, TN 37406

1-800-552-3368

www.mywalker.com

Rev.1 (11-02)

E

N

G

L

I

S

H

E

S

P

A

Ñ

O

L

F

R

A

N

Ç

A

I

S

900 MHz Cordless Telephone

with Clarity

®

Power

™

Technology

Model W425 Owners Manual

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

W425 Features . . . . . . . . . . . . . . . . . . . . . . . . . .6

Connecting Your Telephone . . . . . . . . . . . . . . . . . .10

Choosing a Location . . . . . . . . . . . . . . . . . . . . . . .10

Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . .11

Wall Mount Instructions . . . . . . . . . . . . . . . . . . . . .12

Handset Battery Charging . . . . . . . . . . . . . . . . . . .13

Operating Your Telephone . . . . . . . . . . . . . . . . . . . . . . . .14

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Memory Storage . . . . . . . . . . . . . . . . . . . . . . . . .18

Making and Receiving Calls . . . . . . . . . . . . . . . . . .19

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

FCC Requirements and Regulations . . . . . . . . . . . . . . . . . .22

Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . .24

2

Table of Contents

3

E

N

G

L

I

S

H

When using your telephone equipment, basic safety

precautions should always be followed to reduce the

risk of fire, electric shock and injury to persons

including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on

the telephone.

3. Do not use this telephone near a bathtub, wash

basin, kitchen sink or laundry tub, in a wet

basement, near a swimming pool or anywhere

else there is water.

4. Avoid using a telephone (other than a cordless

type) during a storm. There may be a

remote risk of electrical shock from lightning.

5. Do not use the telephone to report a gas leak in

the vicinity of the leak.

6. Unplug this telephone from the wall outlets before

cleaning. Do not use liquid cleaners or aerosol

cleaners on the telephone. Use a damp cloth for

cleaning.

7.

Place this telephone on a stable surface. Serious

damage and/or injury may result if the telephone

falls.

8. Do not cover the slots and openings on this

telephone. This telephone should never be placed

near or over a radiator or heat register. This

telephone should not be placed in a built-in

installation unless proper ventilation is provided.

9. Operate this telephone using the electrical

voltage as stated on the base unit or the owner’s

manual. If you are not sure of the voltage in your

home, consult your dealer or local power company.

10.

Do not place anything on the power cord. Install the

telephone where no one will step or trip on the cord.

11. Do not overload wall outlets or extension cords

as this can increase the risk of fire or electrical

shock.

12. Never push any objects through the slots in the

telephone. They can touch dangerous voltage

points or short out parts that could result in a risk

of fire or electrical shock. Never spill liquid of

any kind on the telephone.

13.

To reduce the risk of electrical shock, do not take

this phone apart. Opening or removing covers

may expose you to dangerous voltages or other

risks. Incorrect reassembly can cause electric

shock when the appliance is subsequently used.

14.

Unplug this product from the wall outlet and refer

servicing to the manufacturer under the following

conditions:

A. When the power supply cord or plug is

frayed or damaged.

B. If liquid has been spilled into the product.

C. If the telephone has been exposed to rain

or water.

D. If the telephone does not operate normally

by following the operating instructions.

Adjust only those controls that are covered

by the operating instructions. Improper

adjustment may require extensive work by

a qualified technician to restore the

telephone to normal operation.

E. If the telephone has been dropped or the

case has been damaged.

F. If the telephone exhibits a distinct change

in performance.

15. Never install telephone wiring during a lightning

storm.

16. Never install telephone jacks in wet locations

unless the jack is specifically designed for wet

locations.

17. Never touch uninsulated telephone wires or

terminals unless the telephone line has been

disconnected at the network interface.

18. Use caution when installing or modifying

telephone lines

19. Use only the power cord and batteries indicated in

this manual. Do not dispose of batteries in a fire.

They may explode. Check with local codes for

possible special disposal instructions.

SAVE THESE INSTRUCTIONS

Important Safety Instructions

4

Caution: Danger of explosion if battery is

incorrectly replaced. Replace only

with the

same or equivalent type recommended by

the manufacturer. Dispose of batteries

according to the manufacturer's instructions.

1. Use only the approved battery pack

in the handset of your cordless phone.

For Handset Unit: 3.6 V 700mAHr

NiCd Rechargeable Battery

GP70AAS3BMJZ

GPI International Ltd

2. Do not dispose of the battery in

a fire as it may explode. Check with

local codes for possible special

disposal instructions.

3. Do not open or mutilate the battery.

Released electrolyte is corrosive and

may cause damage to the eyes and

skin. It may be toxic if swallowed.

4. Exercise care in handling

batteries in order not to short the

battery with conducting materials

such as rings, bracelets and keys.

The battery or conduction material

may overheat and cause burns.

5. Charge the battery (ies) provided

with or identified for use with this

product only in accordance with the

instructions and limitations specified

in this manual.

6. Observe proper polarity orientation

between the battery pack and the

battery charger.

Safety Instructions for Batteries

5

E

N

G

L

I

S

H

The following items are included as part of

the CS-03 Requirements. The standard

connecting arrangement code for the

equipment is CA11A. This product meets the

applicable Industry Canada technical

specifications.

NOTICE: The Canadian Department of

Communications label identifies certified

equipment. This certification means that the

equipment meets certain telecommunications

network protective operational and safety

requirements. The Department does not

guarantee that the equipment will operate to

the user’s satisfaction. Before installing this

equipment, users should ensure that it is

permissible to be connected to the facilities

of the local telecommunications company.

The equipment must also be installed using

an acceptable method of connection. In

some cases, the company’s inside wiring

associated with a single line individual

service may be extended by means of a

certified connector assembly (telephone

extension cord). The customer should be

aware that compliance with the above

conditions may not prevent degradation of

service in some situations. Repairs to

certified equipment should be made by an

authorized Canadian maintenance facility

designated by the supplier. Any repairs or

alterations made by the user to this

equipment, or equipment malfunctions, may

give the telecommunications company cause

to request the user disconnect the equipment.

Users should ensure for their own

protection that the electrical ground

connections of the power utility, telephone

lines and internal metallic water pipe system,

if present, are connected together. This

precaution may be particularly important in

rural areas. Caution: Users should not

attempt to make such connections themselves,

but should contact the appropriate electric

inspection authority, or electrician, as

appropriate. The Ringer Equivalent Number

is an indication of the maximum number of

termianls allowed to be connected to a

telephone interface. The termination on an

interface may consist of any combination of

devices subject only to the requirement that

the sum of the Ringer Equivalent Number of

all the devices not exceed five.

SAVE THESE INSTRUCTIONS

Important Safety Instructions

6

W425 FEATURES

1. Antenna/Handset Visual Ringer

2. Dial Pad

3. Charge Contacts

4. Channel Button (CH)

5. Talk Button (TALK)

6. Memory Button (MEM)

7. Emergency Memory Storage Buttons

8. Flash Button (FLASH)

9. Mute Button (MUTE)

10. Redial/Pause Button (RD/P)

11. Temporary Tone Button (*)

12. Ringer On/Off

13. Boost Clarity Power On/Off

14. Volume Dial

15. Belt Clip

Getting Started

CH

MEM

FLASH

MUTE

TALK

RD/P

11

44

55

66

77

88

99

**

00

##

22

33

ABCABC

GHIGHI

PQRSPQRS

TUVTUV

WXYZWXYZ

JKLJKL

MNOMNO

DEFDEF

1

2

4

5

6

7

8

9

10

3

RINGER

OFF ONOFF ON

VOLUMEVOLUME

BOOST

CLARITY POWER

14

13

12

15

11

7

E

N

G

L

I

S

H

W425 FEATURES

1. Visual Ringer

2. Charging Contacts

3. Handset Tab

4. Base Antenna

5. In Use/Charge LED (GREEN)

6. Power LED (RED)

7. Page

Getting Started

POWER

PAGE

IN USE/

CHARGE

1

2

3

4

5

6

7

8

W425 FEATURES

1. Pulse/Tone

2. BOOST On/Off

3. AC Adapter Jack

4. Telephone Line Jack

5. Desk/Wall Mounting Bracket

Getting Started

PULSE/TONEPULSE/TONE BOOST

ON/OFF

BOOST

ON/OFF

TELTEL

9VDC

500mA

9VDC

500mA

USE ONLY WITH CLASS TWO

POWER SOURCE

USE ONLY WITH CLASS TWO

POWER SOURCE

1

2

3

4

5

9

E

N

G

L

I

S

H

W425 FEATURES

1. Ringer On/Off

2. Volume Up/Down

3. Ring Style

Getting Started

RINGER

OFF ON

RINGER

OFF ON

VOLUMEVOLUME

RIN

G

STYLE

RIN

G

STYLE

1

2

3

10

CONNECTING YOUR TELEPHONE

1. Carefully remove your cordless

telephone from its box. If there is

any visible damage, do not attempt

to operate this equipment. Return it

to the place of purchase.

2. Check to be sure that you have all

items that come with your W425

telephone. You should have a

HANDSET, BASE UNIT, AC ADAPTER,

BATTERY, MOUNTING BRACKET, 6

INCH AND 6 FOOT TELEPHONE

LINE CORD, BELT CLIP and OWNERS

MANUAL.

If at any time you have questions about

your W425 please contact our Customer

Service Department at:

1-800-552-3368 or 423-622-7793

CHOOSING A LOCATION

1. This phone requires a modular

phone jack (RJ11) and a standard

120-volt outlet.

2. Plug the AC adapter directly into

outlet.

3. Do not plug other appliances into

outlet or have outlet controlled by

a wall switch.

4. Chose a location that is out of the

way of normal activities

CAUTION: Always connect the AC

adapter to the phone before you

connect it to the AC power. When

you finish, disconnect the AC power

before you disconnect it from the

phone.

Getting Started

11

E

N

G

L

I

S

H

DESKTOP INSTALLATION

Follow these instructions to place the

base on a desk or table top using the

supplied bracket.

1. Insert the bracket’s tab into the

base’s upper tab slots in the

direction of DESKTOP marked on

the bracket, then press down on

the bracket’s clips and insert them

into the clip slots.

2. Plug one end of the supplied

modular telephone line cord into

the TEL jack located on the back

of the base of the phone.

3. Plug the modular telephone line

cord’s other end into a modular

phone jack.

4. Insert the supplied AC adapter’s

plug into the jack marked DC 9V

500mA located on the back of

the telephone base.

5. Route the adapter’s cord through

the strain relief slot on the bracket.

6. Plug the adapter into a standard

AC power (electrical) outlet.

7. Lift the base’s antenna to a

vertical position.

8. Set the TONE/PULSE switch

located on the back of the base

to correct dialing mode. Please

check with your local Phone

Company if uncertain of the

type of service.

9. Place handset in the cradle to

begin initial charging.

Remember, you must charge

the phone for at least 12 hours

before you use the phone for

the first time.

Getting Started

PULSE/TONEPULSE/TONE BOOST

ON/OFF

BOOST

ON/OFF

TELTEL

DC 9V

500mA

DC 9V

500mA

USE ONLY WITH CLASS TWO POWER SOURCEUSE ONLY WITH CLASS TWO POWER SOURCE

12

WALL MOUNTING INSTRUCTIONS

The base unit may be mounted on a

standard wall plate.

1. With the back of the unit facing

up insert the supplied mounting

bracket’s tabs into the base’s

lower tab slots in then direction

of WALL MOUNT marked on the

bracket, then press down on the

brackets clips and insert them

into the clip slots.

2. Plug one end of the supplied short

modular telephone line cord into

the TEL jack located on the back

of the base of the phone.

3. Insert the plug of the AC adapter

into the jack marked DC 9V

500mA located on the back of

the telephone base.

4. Route the adapter’s cord through

the narrow groove located on the

back of mounting bracket to

secure the cord.

5. Plug the short modular telephone

line cord into the wall plate jack,

then align the mounting bracket’s

keyhole slots with the wall plate

studs and slide the base of the

phone downward to secure it on

the wall.

6. Plug the adapter into a standard

AC power (electrical) outlet.

7. Press and lift out the handset

holder tab, turn it around so the

narrow tab end extends out and

slide back into its slot. This will

hold the handset in the cradle

when the phone is wall mounted.

8. Lift the base’s antenna to a

vertical position.

9. Set the TONE/PULSE switch

located on the back of the base to

correct dialing mode. Please

check with your local Phone

Company if uncertain of the type

of service.

10.Place handset in the cradle to

begin initial charging.

Remember, you must charge the

phone for at least 12 hours

before you use the phone for the

first time.

Getting Started

13

E

N

G

L

I

S

H

HANDSET BATTERY CHARGING

The battery in the handset must be fully

charged for 12 hours before using the

telephone for the first time.

1. Place the handset in the base.

The CHARGE LED on the base

will light green.

2. After the batteries are fully

charged, check for dial tone by

pressing TALK on the handset.

3. When the handset battery gets

low, there will be 2 beeps every

30 seconds and the TALK button

will flash. If the battery becomes

low while you are on a call, you

will be disconnected after about

two (2) minutes. Terminate the

call and recharge the battery.

To recharge battery pack, place the

handset in the base. The unit can charge

in the base unit either face up or face

down. If charging in the face up position,

the belt clip must be removed so the

handset will connect with the charging

contacts in the base.

1. Make sure the contact points are

touching and the CHARGE LED is

lit.

2. Be careful not to short battery

with conducting materials such

as rings, bracelets and keys.

BATTERY LIFE

Talk Time: 4 hours

Standby: 8 days without usage

Actual amounts will vary depending on

the amplifier settings used.

Replace battery every two (2) years.

REPLACEMENT BATTERIES

The W425 uses a 3.6Volt 700mAhr

NiCd Rechargeable 3 cell (AA Type)

battery. It can be replaced with

RadioShack Battery Part Number

23-298.

To Install Batteries

1. Remove battery cover.

2. Install battery.

3. Close battery cover.

4. Charge for 12 hours before first use.

Getting Started

BATTERY

CONNECTOR

BATTERY

PACK PLUG

BATTERY

COMPARTMENT

COVER

14

FEATURES

Clarity

®

Power™ Technology

With the Clarity Power feature the high

frequency sounds are amplified more

than the low frequency sounds so that

words are not just louder, but clearer

and easier to understand.

Boost Clarity Power On/Off Button

The W425 has a BOOST CLARITY

POWER button that controls the loudness

of the receiver. Once the BOOST

CLARITY POWER button is pressed, an

extra level of amplification is added over

the entire range of the volume control.

The default state of this button is

determined by the BOOST switch (back

of base of unit, see below). During a

call, the BOOST CLARITY POWER button

can toggle the Clarity Power function on

or off according to the user’s needs.

The TALK button will light

ORANGE to

indicate the

CLARITY POWER feature is

activated.

WARNING: When the TALK button is lit

ORANGE volume may be at a high level.

To protect hearing, lower the volume

control to minimum before using.

Volume Dial

The dial controls the level of volume the

handset and headset receive. The volume

dial provides up to 15 dB of volume

before the BOOST CLARITY POWER button is

activated.

Once the button is pressed, the

W425 will provide up to 30 dB of gain.

Boost On/Off Switch

This switch will disable the reset feature

of the BOOST CLARITY POWER button

as follows:

ON- When the BOOST ON/OFF switch

is set to “ON”, the Boost function will be

ON every time a call starts, and will

default to ON every time the phone

hangs up.

During a call, the BOOST

CLARITY POWER

button can toggle the

Clarity Power ON or OFF according to

the user’s needs.

OFF- When the BOOST ON/OFF switch

is set to “OFF”, the Boost function (Clarity

Power) will be OFF every time a call

starts, and the user will need to press the

BOOST CLARITY POWER button in order

to gain the extra level of amplification. If

the phone hangs up, the Clarity Power

will reset to OFF. During a call, the

BOOST CLARITY POWER button can

Operating Your Telephone

15

RIN

G

ER

OFF ON

RIN

G

ER

OFF ON

VOLUMEVOLUME

RING

STYLE

RING

STYLE

E

N

G

L

I

S

H

toggle the Clarity Power function on or

off according to the user’s needs.

Ringer Controls

Ringers and ringer controls are located in

both the handset and the base of the

W425.

Handset Ringer

Set the switch marked RINGER ON/OFF

located on the side of the handset. The

ringer switch must be set to ON for the

handset to ring signaling an incoming

call.

Base Ringer

The base ringer includes ringer volume

and ring style adjustments located on the

side of the base of the telephone. Adjust

the volume of ring by pressing the

VOLUME UP or DOWN switch until the

desired ring volume is achieved. There

are six (6) levels of volume available.

The style of ring or cadence can also be

adjusted by pressing the RING STYLE

button. Six (6) styles are available

allowing you to customize your ring.

The ringer will sound for 2 seconds

while choosing a ringer style, to allow

the user to make a choice.

NOTE: If both handset and base

ringer’s are set to OFF, the visual

ringer will flash to indicate there is

an incoming call.

Visual Ringer

Visual ringers are located in both the

handset antenna and the base of the

telephone. When an incoming call is

received, these lights will flash. The

handset visual ringer will be lit when

the phone is in use.

Operating Your Telephone

RINGER

OFF ONOFF ON

16

Headset/Neck Loop Jack

A 2.5 mm jack is located on the top of

the of the telephone handset that can be

used in conjunction with a headset.

While in headset mode, the volume of

headset is controlled by the telephone.

The same 2.5 mm jack can be used for

neck loops, in conjunction with an

adapter to the 3.5 mm jack.

Ordering a Headset

In the event you wish to purchase a

headset for your W425, please

contact Plantronics at 1-800-544-

4660 for location near you. We

recommend using the Plantronics

M110 headset.

Flash

The FLASH button is activated to use

custom calling services such as Call

Waiting or Three Way Calling. Please

contact your local telephone company for

information on these services.

Mute

The MUTE button allows the user to conduct

a private conversation that you do not

want the person on the other end to

hear. While in the mute mode, the

MUTE

button will become RED and the

microphone in the handset is disabled.

Pressing the MUTE button again will

disengage the MUTE feature.

Redial/Pause

The RD/P button operates both the last

number redial and the pause feature.

Last Number Redial

The last number dialed (up to 32

digits) is stored in the redial memory

until another number is dialed.

To Use this Feature

1. Press the TALK button.

2. When you hear the dial

tone, press the RD/P button.

3. The phone will automatically

dial for you.

Pause Feature

A four (4) second pause may be

inserted into the speed dialing of

the telephone numbers. Press the

RD/P button at the required point

during storage of a number into

memory.

Operating Your Telephone

17

E

N

G

L

I

S

H

Lighted Key Pad

The key pad will light for fifteen (15)

seconds after removing from the base

when there is an incoming call. To

reactivate the feature while in standby or

in use, press any key.

Page / Handset Locator

To send a page signal from the base to

the handset, press the PAGE button located

on the base of the telephone. A series of

rings will sound from the handset.

To locate the handset if it is away from

the base, press and hold the PAGE button

for approximately five (5) seconds. A

series of rings will sound for approximately

sixty (60) seconds. Return the handset to

the base or press the TALK button to

cancel the page. Press TALK again to

return to standby mode.

40 Channel Operation

The W425 cordless telephone

automatically searches and selects the

clearest of 40 channels when it is being

used.

Security Code

The security code prevents your cordless

phone from being accessed by a phone

on a different line. Once the handset

battery is fully charged, the handset will

automatically select the code from over

65,000 combinations. The code is

changed every time the handset is

placed in the cradle.

If you have trouble with placing or

receiving calls, a lost security code may

be the cause of the problem. When this

occurs, the handset can no longer

communicate with the base. Reset by

placing the handset on the base for 5-10

seconds. If that does not work, unplug

the AC adapter from the wall outlet.

Disconnect the handset battery for 5-10

seconds, and then reconnect. Place

handset back on the base and then

reinsert the AC adapter.

Hearing Aid Compatibility

The handset has a special coil inside

of it to couple the sound to hearing aids

equipped with T-Switches/T-Coils.

Operating Your Telephone

18

MEMORY STORAGE

Emergency Storage Buttons

Three emergency buttons are located on

the handset. These storage buttons can

be programmed with numbers of up to

16 digits.

Memory Storage Locations

The W425 also has 10 indirect or two

touch memory locations on the telephone

(0-9) that can be programmed to dial

frequently called numbers of up to 16

digits.

To Store numbers into memory

1. Press the MEM button.

2. Dial the number you wish to store.

3. Press the MEM button again.

4. Press either the emergency button

or the number on the dial pad that

you wish to store the number to.

5. A long beep will indicate the

programming process is complete.

During the memory storage process the

TALK button will flash GREEN. In the

event of a power outage memory is

retained of at least six (6) hours.

To Change a Number Stored into Memory

Replace a stored number by programming

a new number in its place.

To Delete a Number Stored into Memory

1. Press and release the MEM

button.

2. Press the * key once for each digit

in the number you are deleting.

3. Press the MEM button again.

4. Press the button for the memory

location you want to delete the

number from.

Operating Your Telephone

19

E

N

G

L

I

S

H

MAKING AND RECEIVING PHONE CALLS

Placing a Phone Call

1.Press the TALK button. (TALK button

will illuminate).

2. Dial the number you wish to call.

3. Adjust the rotary Volume Control to

desired level.

4. Press the Clarity Power Button

(

activates the Clarity Power Technology)

to gain the extra level of amplification,

if needed.

Refer to BOOST CLARITY POWER

ON/OFF and BOOST ON/OFF for

additional information on volume controls.

To Dial from Memory

1.Press the TALK button.

2.Press the MEM button.

3.Press the number on the dial pad

where the desired number has been

stored.

4.The call will automatically dial.

5.Adjust volume and Clarity Power as

needed.

To Dial From Emergency Storage Location

1.Press the TALK button.

2.Press the desired emergency button.

3.The call will automatically dial.

4.Adjust volume and Clarity Power as

needed.

To use a TONE service on a Pulse Line

1.Dial the number you wish to call

2.When the call is answered, press the *

key. Additional numbers you dial are

sent as tone signals.

3.After completing the call, press TALK

or return the handset to the base. The

phone will automatically reset.

Receiving a Call

Handset in Base of Telephone

1. Lift the handset. Do not press

TALK. You will automatically be

connected.

Handset out of Base

1. Press the TALK button.

Ending a Call

Place the handset in the base cradle or

press the TALK button to disconnect the line.

Note: When placing or receiving a call, the

handset visual ringer will lite, indicating the

phone is in use.

Operating Your Telephone

La page charge ...

Clarity Cordless Telephone W425 Manuel utilisateur

Ce manuel convient également à

Clarity Cordless Telephone W425 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents