2
Introduction 4
Main Features
4
Parts and their function
4
Top Panel 4
Rear Panel
6
Setup 7
Using the stand (VOX MINI GO 10/50) 7
Auto Power Off Function
7
Using the Rhythm Section 8
Selecting a rhythm pattern 8
Starting and stopping the playback of a rhythm
pattern
8
Adjusting the volume of a rhythm pattern
8
Changing the tempo of a rhythm pattern
8
Using the looper function
(VOX MINI GO 10/50)
8
Basic usage of looper 8
Synchronous operation of rhythm and looper
9
Using the Tuner 10
User programs and Manual mode
(VOX MINI GO 50 only)
10
Saving a program (VOX MINI GO 50 only)
10
Restoring the factory settings
11
Using the foot switch (VOX MINI GO 10/50)
11
Changing the foot switch function 11
Foot Switch Function Setting mode
11
Foot switch function list
12
Foot switch function details (additional info)
13
Amp Models and Effects 13
AMP model 13
EFFECTS 1 (Modulation types/Octave)
14
EFFECTS 2 (Delay/Reverb types)
14
Troubleshooting 15
Specications
16
Introduction
17
Caractéristiques principales
17
Parties et leurs fonctions
17
Face avant 17
Face arrière
19
Préparation 20
Utilisation du support (VOX MINI GO 10/50) 20
Fonction de coupure automatique d’alimentation 20
Utilisation de la section rythmique 21
Sélection d’un motif rythmique 21
Lancer/arrêter un motif rythmique
21
Régler le volume du motif rythmique
21
Changer le tempo du motif rythmique
21
Utiliser la fonction looper
(VOX MINI GO 10/50)
21
Utilisation de base du looper 21
Fonctionnement synchrone du rythme et du looper 22
Utiliser l’accordeur 23
Programmes utilisateur et mode manuel
(VOX MINI GO 50 uniquement)
23
Mémoriser un programme
(VOX MINI GO 50 uniquement)
23
Rétablir les réglages d’usine
24
Utiliser la pédale-interrupteur
(VOX MINI GO 10/50)
24
Modier la fonction de la pédale-interrupteur 24
Mode de réglage de la fonction de la pédale-
interrupteur
24
Liste des fonctions de la pédale-interrupteur
25
Détails sur la fonction de la pédale-interrupteur
(informations complémentaires)
26
Modèles d’amplis et d’effets 26
Modèle d’ampli 26
EFFECTS 1 (Modulation/Octave)
27
EFFECTS 2 (Delay/réverbération)
27
Dépannage 28
Fiche technique
29
Einleitung
30
Die wichtigsten Merkmale
30
Teile und Funktionen
30
Oberseite 30
Rückseite
32
Vorbereitung 33
Verwenden eines Standfußes (VOX MINI GO 10/50) 33
Energiesparfunktion 33
Verwendung der Rhythmusfunktion 34
Anwahl eines Rhythmus-Pattern 34
Starten und Anhalten der Rhythmusbegeleitung 34
Lautstärke der Rhythmusbegleitung 34
Ändern des Rhythmus-Tempos
34
Verwendung der Looper-Funktion
(VOX MINI GO 10/50)
34
Grundlegende Verwendung des Loopers 34
Synchroner Betrieb von Rhythmus und Looper
35
Verwendung der Stimmfunktion 36
Nutzer-Programme und Manual-Modus
(nur VOX MINI GO 50)
36
Speichern eines Sounds
(nur VOX MINI GO 50)
36
Laden der Werksvorgaben
37
Verwendung des Fußschalters
(VOX MINI GO 10/50)
37
Ändern der Funktion des Fußschalters 37
Einstellungsmodus der Fußschalterfunktion
37
Funktionsliste des Fußschalters
38
Funktionsdetails des Fußschalters (Zusatzinfo)
39
Verstärkermodelle und Effektes 39
Verstärkermodelle 39
EFFECTS 1 (Modulation-/Octave-Effekttypen)
40
EFFECTS 2 (Delay/Hall-Effekttypen)
40
Fehlersuche 41
Technische Daten
42
En
Table of contents
Fr
Table des matière
De
Inhaltsübersicht
3
Introducción 43
Características generales
43
Partes y sus funciones
43
Panel superior 43
Panel posterior
45
Conguración 46
Uso del soporte (VOX MINI GO 10/50) 46
Función de desactivación automática
46
Utilizar la sección de percusió 47
Seleccionar un patrón de percusión 47
Iniciar y detener la reproducción de un patrón de
percusión
47
Ajustar el nombre de un patrón de percusión
47
Cambiar el tempo de un patrón de percusión
47
Uso de la función looper
(VOX MINI GO 10/50)
47
Uso básico del looper 47
Funcionamiento simultáneo del ritmo y el looper 48
Uso del anador 49
Programas del usuario y modo Manual
(solo VOX MINI GO 50)
49
Guardar un programa
(solo VOX MINI GO 50)
49
Restablecer los ajustes de fábrica
50
Uso del pedal interruptor
(VOX MINI GO 10/50)
50
Cambiar la función del pedal interruptor 50
Modo de conguración de la función del pedal
interruptor
50
Lista de funciones del pedal interruptor
51
Detalle de las funciones del pedal interruptor
(información adicional)
52
Modelos de amplicador y efectos 52
Modelo AMP 52
EFFECTS 1 (Modulación/Octave)
53
EFFECTS 2 (Retardo/Reverberación)
53
Solución de problemas 54
Especicaciones
55
はじめに
56
主な特長
56
各部の名称と機能
56
トップ・パネル 56
リア・パネル
58
セットアップ 59
スタンドを使う（VOX MINI GO 10/50） 59
オート・パワー・オフ機能
59
リズムを使う 60
リズムを選択する 60
リズムを再生/停止する
60
リズムの音量を調節する
60
リズムのテンポを変える
60
ルーパーを使う（VOX MINI GO 10/50） 60
ルーパーの基本的な使い方 60
リズムとルーパーの同期動作
61
チューナーを使う 62
ユーザー・プログラムとマニュアル・モード
（VOX MINI GO 50のみ）
62
プログラムを保存する
（VOX MINI GO 50のみ）
62
工場出荷時の状態に戻す
63
フット・スイッチを使う
（VOX MINI GO 10/50のみ）
63
フット・スイッチの機能を変更する 63
フット・スイッチ機能設定モード
63
フット・スイッチ機能一覧
64
フット・スイッチ機能詳細（補足）
65
アンプ・モデル、エフェクトの説明 65
アンプ・モデル 65
エフェクト1（モジュレーション/オクターブ） 66
エフェクト2（ディレイ/リバーブ） 66
故障とお思いになる前に 67
仕様
68
Es
Contenido
Ja
目次
4
En
Introduction
Thank you for your purchasing the VOX MINI GO 3/10/50 Portable
Modeling Guitar Amplier. To help you get the most out of your new
instrument, please read this manual carefully.
Main Features
11 amp types
The amplier features 9 amp sounds using the “VET” modeling technology,
as well as a vocoder setting and a line setting for electric acoustic guitars or
keyboards.
Available effects
The amplier features eight high-quality effects: four delay and reverb effects
in addition to three modulation effects and an octave effect.
Rhythm function
Includes 33 types of rhythm patterns with a wide range of variations.
Tuner function
You can tune the guitar or bass connected to the INPUT terminal.
Looper function (VOX MINI GO 10/50)
Provides a simple and user-friendly looper function, which can be used
together with the rhythm function.
Supports mobile batteries
Off-the-shelf mobile batteries can be used as the power supply.
Use with microphone or audio player
Inputs include an AUX IN jack, for connecting an external audio device (MP3
player, etc.), and a MIC IN jack, to where you can connect a microphone.
You can play along with recorded music or accompany your vocals on guitar.
Supports a foot switch (VOX MINI GO 10/50)
By connecting an optional foot switch VFS3, you can manipulate rhythm and
looper functions using your foot.
Parts and their function
Top Panel
INPUT Section
1. INPUT jack
This is where you plug in your guitar.
2. MIC IN jack
Connect the microphone (dynamic microphone).
3. TRIM knob
This knob enables you to adjust the volume level of the
microphone input.
4. SEND knob
Adjust the volume sent from the MIC input to Effect 2
(delay/reverb).
Not available when the AMP selector is set to VOCODER.
AMP section
This section enables you to adjust various amplier settings.
5. AMP selector
This selector enables you to choose an amp model (for additional details, refer
to “Amp model” on page 13). The gain circuit, tone control characteristics,
and circuit layout will be set automatically in accordance with the selected amp
model. You can also select the amplier model or vocoder appropriate for the
LINE input.
6. GAIN knob
This knob enables you to adjust the pre amp gain for the selected amp model.
1
2
3
4
5
6
7
8 9
10
5
VOX MINI GO 3
VOX MINI GO 10
7b
5
7. TREBLE knob (VOX MINI GO 50 only)
Used to adjust the tone in the high-tone range. The tone will be changed
automatically in accordance with the selected amp model.
7b. TONE knob (VOX MINI GO 3/10)
Used to adjust the tone. The tone will be changed automatically in
accordance with the selected amp model.
8. BASS knob (VOX MINI GO 50 only)
Used to adjust the tone in the low-tone range. The tone will be changed
automatically in accordance with the selected amp model.
9. Power select switch (VOX MINI GO 10/50)
This switch adjusts the output wattage of the power amp.
This switch does not affect the PHONES output.
10. VOLUME knob
Used to adjust the output level of the pre-amplier.
EFFECTS section
Here is where you can adjust the settings for the effects. For additional
details on each effect, refer to “EFFECTS 1”, “EFFECTS 2” on page 14.
11. EFFECTS knob 1
Adjust the knob position to switch Effect 1 (modulation/
octave) and set the depth of an effect. To bypass the
effects, rotate the knob all the way to the left.
12. EFFECTS knob 2
Adjust the knob position to switch Effect 2 (delay/
reverb) and set the depth of an effect. To bypass the
effects, rotate the knob all the way to the left.
13. TIME button, LED
This button enables you to set the time of Effect 2
(delay/reverb). Tap this button twice to set the time.
The duration between two taps will be used as the
time value. The LED will ash in sync with the time.
11 12 13
RHYTHM section
14. Genre selector
This enables you to select the genre for a
rhythm pattern.
15. VARIATION button, LED
This is where you can select one of nine
variations for each genre. (see p.8 “Using
the Rhythm Section”)
To enable the tuner function, press and hold
down the VARIATIONS button for more than one
second. (see p.10 “Using the Tuner”)
16. TEMPO button
Set the rhythm tempo. Tap this button twice
to set the tempo. The duration between two
taps will be used as the tempo value.
17. RHYTHM LEVEL knob
This knob controls the volume level of the
rhythm pattern.
18. RHYTHM START/STOP button
This button starts or stops playback of the
rhythm pattern.
Looper section (VOX MINI GO 10/50)
Perform looper operations and settings. For
details about how to use the looper, refer to
"Using the looper function (VOX MINI GO
10/50)" on p.8.
19. LOOP LEVEL knob
Used to adjust the volume during loop
playback
20. LOOP button, LED
Perform operations such as loop recording,
playback, and erasing.
14 15 16
17 18
19
20
6
Program section (VOX MINI GO 50 only)
21. PROGRAM button, LED
Use this button to choose a program. Each time the
PROGRAM button is pressed, the PROGRAM LED turns
green
orange red Off. (Refer to “User programs and
Manual mode” on page 10.) This button is also used to
save new programs. (Refer to “Saving a program” on page
10.)
Power/AUX IN/PHONES Section
22. (Power) button, LED
Pressing and holding down this button enables you to turn
the power on or off. The power LED will light up when the
power is turned on.
The color of the power LED varies depending on the type
of the connected power supply equipment (maximum
current that can be consumed by this instrument).
Green: Lights up when the current of up to 3A can be
consumed by connecting the AC adapter supplied
with this product to the DC19V terminal (DC 12V
terminal for VOX MINI GO 3/10) or by the battery
connected to the DC 5V IN terminal.
Orange: Lights up when the current of up to 1.5A can
be consumed depending on the equipment
connected to the DC 5V IN terminal.
23. AUX IN jack
Connect an external audio device to this jack. This enables you to conveniently
connect an audio player and play your guitar along with the player’s output.
24. PHONES jack
Use this jack if you’re plugging directly in to a mixer, recording device, or if
you’re using headphones. The output signal from this jack is taken before
the power amp, and the character of the guitar amp cabinet is applied to it.
Connecting headphones to this jack will mute the internal speaker.
Be sure to make a stereo connection at the PHONES jack.
19
20
22
23
24
21
Rear Panel
25. Connector protection bar (VOX MINI GO 10/50)
Do not use this protection bar to carry this instrument. To carry the
instrument, use the carry strap provided with this product.
26. DC 19V jack* (*DC 12V jack at VOX MINI GO 3/10)
Connect this jack to the included AC adapter.
The AC adapter should only be used with the main unit. Do not use the
adapter with other devices since doing so may cause a malfunction.
27. DC 5V IN jack (USB type-C connector)
Connect a commercially available mobile battery.
Noise may be heard when the power is supplied from a commercially
available USB AC adapter, so use a mobile battery.
This terminal is only used for input. It cannot supply power to another
device.
Not compatible with USB Power Delivery (USB PD).
28. FOOT SW jack (VOX MINI GO 10/50)
Connect the dedicated foot switch VFS3. For details, refer to "Using the foot
switch" on page 11.
2625 27
28
VOX MINI GO 3VOX MINI GO 50
26 27
21
7
Setup
1. Set the VOLUME knob (10), TRIM knob (3) and RHYTHM LEVEL knob (17) to
the minimum level.
2. Connect the included AC adapter to the DC19V jack (DC 12V jack for VOX
MINI GO 3/10) on the rear panel (26), then plug the adapter into an AC
outlet.
To use an off-the-shelf mobile battery, connect it to the DC 5V IN jack (27)
using a USB type-C cable.
Use a mobile battery with an output of at least 1.5A. Depending on the
mobile battery or USB Type-C used, the power may not be turned on, or the
battery may not be able to provide sufcient power.
When using a mobile battery, the output may be distorted or there may be
noise.
3. Plug your guitar into the INPUT jack on the top panel.
If you also plan to use a CD or MP3 player or a
microphone, connect the player to the AUX IN jack, or
the microphone to the MIC IN jack on the top panel.
4. Press and hold down the Power button until the power
LED lights up and the power turns on.
5. Slowly raise the VOLUME Knob to the desired level.
6. When turning off the power, press and hold down the
Power button until the power LED turns off.
Using the stand (VOX MINI GO 10/50)
The VOX MINI GO 10/50 can be set at an
angle by pulling out two stands at the bottom
of the main unit (refer to the gure on the
left).
Be sure to install the stand on a at surface.
If you set the stand at an angle on a slope, it
may fall over.
Do not apply an excessive load such as by
leaning against the amplier.
Auto Power Off Function
The Auto Power Off function automatically turns the power off when the
amplier is not used or when the sound is not output for approximately
one hour. When the power is turned off, it’s not restored even if a knob or
selector is used. Turn on the power again.
The Auto Power Off function does not work during rhythm playback or looper
operation (during recording, playback, or overdubbing).
If the volume or variation of the output sound is extremely small, the Auto
Power Off function may be activated. Also, depending on the settings and
environment, the Auto Power Off function may not be activated due to noise
even if you are not playing.
Setting the Auto Power Off function to enable or disable
1. Press and hold down the TEMPO button (16) and turn on the power.
2. The VARIATION LED (15) will indicate the current setting.
Enable
Disable
3.
Press the TEMPO button (16) to switch between the enable and disable setting.
4. Wait a few seconds without using any of the buttons or controls. The unit
will automatically switch to normal operation.
The Auto Power Off function enable and disable setting will be saved even
when the power is turned off.
8
Using the Rhythm Section
Selecting a rhythm pattern
1. Select a genre for each rhythm pattern using the GENRE selector (14).
2.
Select a variation for each rhythm pattern using the VARIATION button (15).
One of three VARIATION LEDs lights up green, orange or red in the following
sequence each time you press the button.
Variation 1
Variation 2Variation 3
Starting and stopping the playback of a rhythm pattern
Press the RHYTHM START/STOP button (18) to start or stop playing a
rhythm pattern. During playback, the VARIATIONS LED that corresponds
to the selected rhythm pattern will ash in sync with the tempo.
[TIP] The three VARIATION LEDs light up momentarily at the beginning of each bar.
Adjusting the volume of a rhythm pattern
Use the LEVEL knob (17) to adjust the volume of a rhythm pattern.
Changing the tempo of a rhythm pattern
You can adjust the rhythm tempo within the range of 40 to 240 BPM by
pressing the TEMPO button twice at the required interval.
[TIP] If you press the button several times in time with the song, it will help you set
the correct tempo.
[TIP] If you press the TEMPO button while playback is suspended, the VARIATION LED
will blink in time with the tempo (the rhythm will not be played back). If you
change the rhythm pattern or turn the RHYTHM LEVEL knob fully
counterclockwise, the blinking will stop.
Using the looper function (VOX MINI GO 10/50)
The looper function allows you to perform jam sessions
while looping phrases recorded using a guitar or
microphone, or play a performance in real time while
repeating overdubbing.
Basic usage of looper
1. Press the LOOP button (20) to enable record standby
mode. (The LOOP LED blinks red.)
2. Press the LOOP button again or start playing the guitar to
start recording. (The LOOP LED lights up red.)
The minimum recording time is approximately 0.25 seconds and the
maximum recording time is approximately 45 seconds.
The sound being input via the AUX IN jack or the rhythm pattern is not
recorded.
Depending on the equipment used or settings, recording may start due to
noise even if you are not playing.
3. Press the LOOP button to exit recording and play back the recorded
interval. (The LOOP LED lights up green.)
4. Press the LOOP button during playback to start overlap recording, or quickly
press the LOOP button twice to stop playback.
5. If you hold down the LOOP button during playback after overdubbing, the
overdubbing is undone (the overdubbed phrase is muted), and is redone
(the mute is released) when you press and hold the LOOP button again.
Pressing and holding the LOOP button while playback is suspended erases
recorded data.
6. If you press the LOOP button while playback is suspended, the recorded
phrase will be played back in a loop from the beginning. Also, if you press
and hold the LOOP button while playback is suspended, the recorded
phrase will be deleted (the phrase will be played back for a moment).
9
List of the LOOP button operations and functions
LOOP LED status
Short-press LOOP
button
Twice-press LOOP
button (*1)
Press-hold LOOP
button
Suspended (does
not record)
Turns OFF Turns OFF
(The twice-press and press-hold functions
are not available.)
Recording standby
Blinks red Recording starts
Recording Lights up red
Recording ends
Plays back
Recording ends
Stops
Cancels recording,
Stops
Suspended
(recorded)
Blinks green Playback starts Stops Erases
Plays back
Lights up green
(*2)
Overdubbing Stops
Undoes/Redoes (*3)
Overdubbing
Lights up orange
(*2)
Plays back Stops
Undoes
Plays
back
*1 Press the button twice within half a second.
*2 The LED turns off for a moment at the beginning of a loop.
*3 If you have never overdubbed, the recorded phrases will be erased.
Synchronous operation of rhythm and looper
The looper function can be used together with the rhythm function.
Looper recording during rhythm playback (quantize)
If you record a looper during rhythm playback, the loop length is automatically adjusted
to match the rhythm beat or bar length when recording is stopped (quantize).
[TIP] The rhythm tempo is quantized to one beat, two beats, or a well-separated bar length.
If the genre is 3/5/7, the rhythm tempo is not quantized to two beats long.
[TIP] The relative position between the beginning of the rhythm and the beginning of
the looper is stored, and when simultaneous playback is performed, the rhythm
and looper are played back while the same relative position as Recording mode
is maintained (refer to "Simultaneous playback of rhythm and looper").
Rhythm playback during looper playback (Automatic tempo adjustment)
If the rhythm is played back during loop playback, the rhythm tempo is automatically
set based on the rhythm tempo before playback and the length of the recorded phrase.
[TIP] Calculate the tempo at which the looper's phrase length is one beat, two beats, or a
well-separated bar length. The number of bars is 1, 2, 4, 8, 12, 16, 24, 32, or 48.
If the genre is 3/5/7, the rhythm is not set to a tempo that is two beats long
[TIP] When the looper is recorded and quantized during rhythm playback, the tempo
will not change even if you stop the rhythm and play it back again.
Simultaneous playback of rhythm and looper
When a looper has already been recorded and both the rhythm and the
looper are suspended, if you press both the RHYTHM button and the LOOP
button, the rhythm and looper start playback at the same time. If a looper is
recorded during rhythm playback, the rhythm and looper are played back
while the same relative position as Recording mode is maintained.
[TIP] The looper is always played from the beginning, and the rhythm is played from
the middle according to the relative position.
[TIP] The rhythm tempo is automatically adjusted even in the case of the
simultaneous playback.
If a looper is recorded while the rhythm is suspended, the relative position is cleared to 0.
If the rhythm tempo is changed, the relative positions of the rhythm and looper are cleared to 0.
( ll )
( cut )
( ll )
( cut )
. . .
10
Using the Tuner
The tuner function lets you tune a guitar that’s connected to the INPUT
jack. The tuner detects the pitch of the input sound, then indicates the
discrepancy from the standard pitch of E.
1. Press and hold down the VARIATION button for more than one second.
Effect 1 will be bypassed, and the tuner function will turn on.
All effects are bypassed.
(No valid signal is being input.)
2. Play the open 6th string.
Be careful not to touch any other strings.
3. Tune the guitar so that only the center green LED lights up, as shown on
the right.
The pitch is slightly sharp.
The pitch is sharp.
In tune.
The pitch is slightly at.
The pitch is at.
[TIP] The tuner recognizes the pitch of E in any octave.
This is useful if you want to tune to harmonics or tune other musical instruments,
such as a bass guitar.
[TIP] Once you tune the 6th string using the tuner function, tune the other strings in
reference to the 6th string.
4. Press the VARIATION button again or turn the EFFECTS knob 1 to
switch the type of Effect 1; the tuner ends, and the bypass is released.
[TIP] In the VOX MINI GO 50, the tuner ends even if the program is switched.
User programs and Manual mode
(VOX MINI GO 50 only)
You can save the tones produced by adjusting the amplier or EFFECTS
knob as user programs A, B, and C. The saved programs can be easily
called using the PROGRAM button (21) or the foot switch.
The power select switch, TRIM, SEND, RHYTHM section, and LOOP section
settings cannot be saved in a program.
Each time you press the PROGRAM button, user programs A, B, and C
(green, orange, and red) and Manual mode (LED off) are called in
sequence. In Manual mode, all the knob positions are reected on
sounds as they are.
[TIP] The VOX MINI GO 3/10, which does not provide any user programs, is always in
Manual mode.
Saving a program (VOX MINI GO 50 only)
After adjusting the various knobs and buttons on the top panel to create
your desired sound, it can be saved (written) as a user program.
[TIP] The saved programs can be called using the PROGRAM button or the foot
switch.
1. Hold down the PROGRAM button (21) for at least one second (until the
PROGRAM LED starts blinking).
2. Press the PROGRAM button to select the save location.
[TIP] To cancel the write operation, press the TIME button (13).
3. Hold down the PROGRAM button for at least 2 seconds (until the LED
changes from blinking to lit). The program is saved at the selected
location, and the saved program is selected.
If you switch to another program or turn off the amp before saving the sound
that you are creating, the changes that you made will be lost.
11
Restoring the factory settings
Here’s how to restore all settings of the VOX MINI GO to their factoryset state.
1. Turn off the power.
2. While holding down the VARIATION button, turn on the amp. After the
VARIATION LED blink, release the pressed button.
[TIP] If you decide to cancel initialization at this point, press the TIME button.
3. Hold down the VARIATION button for at least 2 seconds (until the LED
changes from blinking to lit).
Initialization is completed, and the amp returns to normal operation.
Never turn off the power while initialization is in progress.
Using the foot switch (VOX MINI GO 10/50)
By connecting the foot switch VFS3 to the FOOT SW terminal (28) on the
rear panel, you can control effects, rhythms, and loopers with your foot.
Do not connect a product other than the VFS3.
The following functions are assigned at the time of factory shipment.
SW1 SW2 SW3
VOX MINI GO 10
Effect 2 On/Off
Rhythm playback/stop
Looper recording/Playback/Overdub
VOX MINI GO 50 Program switch
Rhythm playback/stop
Looper recording/Playback/Overdub
Changing the foot switch function
Each function of the foot switch can be changed simply by operating the
foot switch on the top panel while holding it down during normal
operation. For information about the functions that can be assigned, refer
to "Foot switch function list" on the following page.
Operate the top panel and foot switch separately, except when changing a function.
[TIP] To prevent a function from being changed unintentionally, you can disable the
function change operation during normal operation (refer to "Foot Switch
Function Setting mode).
[TIP] The assigned functions are stored in this instrument side, so settings are
retained even when the power is turned off.
Foot Switch Function Setting mode
This is the dedicated mode for setting the foot switch function.
1. Start with the power turned off.
2.
Connect the foot switch, and while pressing the LOOP button (20), turn the power on.
3.
When all LEDs except (power) LED (22) start blinking slowly, release the
button you are pressing. The blinking color of the LED indicates whether
the function change operation during normal operation is enabled (orange)
or disabled (green). Press the LOOP button to switch Enable and Disable.
If you set to Disable, you cannot change the foot switch function during
normal operation.
4. Press the foot switch corresponding to the settings you want to change (do
not keep the switch held down). The LED on the pressed switch lights up
green to indicate that it is a setting target. The function currently assigned
to the target switch is displayed on the top panel.
5. Operate the knob or switch to change the function (refer to "Foot switch
function list" on the following page).
6. Press and hold the (power) button to turn the power off.
VFS3
12
Foot switch function list
Function Operation when the foot switch is pressed
Assignment method (While holding down the foot switch
during normal operation, perform the following operation.)
Display in Foot Switch Function Setting mode
Effect 1 On/Off
Each time it is pressed, Effect 1 is switched on or off. Turn the EFFECTS knob 1. The TIME LED (green) blinks regularly.
Effect 2 On/Off
Each time it is pressed, Effect 2 is switched on or off. Turn the EFFECTS knob 2. The TIME LED (red) blinks regularly.
Delay/reverb time
The delay/reverb time is set at the interval at which the switch is pressed twice.
Press the TIME button. The TIME LED (red) blinks.
Tuner On/Off Each time it is pressed, the tuner is switched on or off.
For details, refer to "Foot switch function details (additional info)" on the next page.
Press and hold the VARIATION button. The VARIATION LED (red - green - red) moves
smoothly from side to side.
Rhythm variation
Each time it is pressed, the rhythm variation is switched 1 2 3 1...
Press the VARIATION button. The VARIATION LED (green) lights up in the order
of 1
2 3.
Rhythm tempo
The rhythm tempo is set at the interval at which the switch is pressed twice.
Press the TEMPO button. The center (green) of the VARIATION LED blinks.
Rhythm playback/stop Each time it is pressed, the rhythm is switched to playback or stop. Press the START/STOP button. During normal operation, the LED turns in the
same way as rhythm playback.
Rhythm mute On/Off Each time it is pressed, the rhythm mute is switched on or off. Turn the RHYTHM LEVEL knob. The VARIATION LED (green) blinks regularly.
Looper recording/
playback/overdub
Each time you press the foot switch, the looper operation transitions.
LOOP mode 1: Record
Playback Overdub
LOOP mode 2: Record
Overdub Playback
LOOP mode 3: Record
Playback Record
For details, refer to "Foot switch function details (additional info)" on the next
page.
Press the LOOP button.
LOOP mode 1 is only available during normal operation. In
Foot Switch Function Setting mode, each time the LOOP
button is pressed, LOOP mode is switched to 1
2 3
(green
orange red).
To continuously switch LOOP mode, wait at least half a
second before pressing the LOOP button. If you press the
LOOP button twice within half a second, "looper stop"
will be assigned.
LOOP mode 1: The LOOP LED (green) lights up.
LOOP mode 2: The LOOP LED (orange) lights up.
LOOP mode 3: The LOOP LED (red) lights up.
[TIP] You can assign different modes to
respective switches to make usage more
convenient.
Looper stop Press once to stop the looper. Press the LOOP button quickly twice.
(During normal operation: Performs the looper stop
operation.)
The LOOP LED (green) blinks.
The looper is suspended (with phrase) during
normal operation.
Looper undo/redo Each time it is pressed, undo/redo is performed.
If you press and hold the button while suspended, the recorded phrases will be erased.
If you press and hold the button during playback and overdubbing has never been
performed, the recorded phrases are erased, and the looper is stopped.
Press and hold the LOOP button.
(During normal operation: Performs undo/redo operation.)
The LOOP LED (green) blinks quickly twice every
second.
Looper mute On/Off Each time it is pressed, the looper mute is switched on or off. Turn the LOOP LEVEL knob. The LOOP LED (green) blinks regularly.
Collective control of
rhythm and looper
Control the rhythm and looper all at once.
Looper not recorded: Start rhythm playback
Start looper recording End
recording (start playback)
Looper recorded: Start simultaneous playback of rhythm and looper (except
LOOP mode 3)
Press twice quickly to stop both.
For details, refer to "Foot switch function details (additional info)" on the next page.
Press both the START/STOP button and the LOOP button
at the same time.
[TIP] In Foot Switch Function Setting mode, you can
press the LOOP button while holding down the
START/STOP button to switch LOOP mode.
VARIATION LED:
Turns in the same way as rhythm playback during
normal operation.
LOOP LED:
LOOP mode 1: The LOOP LED (green) lights up.
LOOP mode 2: The LOOP LED (orange) lights up.
LOOP mode 3: The LOOP LED (red) lights up.
Program switching
(VOX MINI GO 50 only)
Each time it is pressed, the user program is switched to A
B C A... Press the PROGRAM button.
(During normal operation: Switches the program.)
The PROGRAM LED turns green orange red.
No assignment (Nothing occurs.) Press and hold the foot switch.
("No assignment" cannot be set during normal operation.)
All turns off.
13
Foot switch function details (additional info)
Tuner On/Off
If the tuner is turned on by operating the foot switch, three LEDs of the foot
switch are switched to tuner display (the VARIATION LED remains set to the
original display).
If you press and hold the VARIATION button, the VARIATION LED is switched to the
tuner display, but the display of the foot switch remains unchanged. In any case,
when the foot switch is pressed while the tuner is on, the tuner is turned off.
[TIP] When the LED of the foot switch is in the tuner display, the tuner is turned off
even if you press the foot switch when it is assigned to another function.
Looper recording / playback / overdub and LOOP mode
Each time you press the foot switch, the looper operation transitions. You can
use three modes of operation, including the same operation as the LOOP
button on the top panel (LOOP mode 1) (refer to “Foot Switch Function
Setting mode” on page page 11).
LOOP mode 1: Basically operates in the same way as the LOOP button.
However, if the switch is pressed in the suspended (unrecorded) state, the
recording standby is skipped, and recording starts immediately.
LOOP mode 2: If the switch is pressed while recording, recording is stopped
and switched to Overdubbing mode. Others are the same as LOOP mode 1.
LOOP mode 3: If the switch is pressed while suspended (including the
recorded state), during playback, or during overdubbing, the previous
phrases are erased, and new recording starts.
[TIP] A different mode can be assigned to multiple switches, so you can freely
combine the recording - playback - overdubbing order when playing.
Collective control of rhythm and looper
You can control both the rhythm and the looper at once with a single foot switch.
When both the rhythm and the looper are suspended while no looper has
been recorded (or in LOOP mode 3), the mode transitions in the order
of Start rhythm playback
Start looper recording End recording (Start
playback) each time the button is pressed.
[TIP] If you press both during playback, operation will be the same as "Looper recording /
playback / overdubbing". Press twice quickly to stop both the rhythm and the looper.
If you press this button when both the rhythm and the looper are suspended
while the looper is recorded, the rhythm and looper start playback at the
same time (excluding LOOP mode 3).
[TIP] The looper is always played back from the beginning, and the rhythm is played
back from the middle according to the relative position when recording the
looper (refer to "Simultaneous playback of rhythm and looper" on page 9).
When either button is pressed during playback, the relative position is not
reected.
If the button is pressed while the looper is playing back and the rhythm is
stopped, the looper status does not change and the rhythm starts playing from
the beginning.
Amp Models and Effects
This section describes characteristics of each amp model and effect.
AMP model
DELUXE CL
This dual channel, 22W blackface design from the 60’s used 6V6 power
tubes and a tube driven reverb to produce a big sound at a lower wattage.
Our modeling is based on the Vibrato channel.
BOUTIQUE CL
This models the clean channel of a high-quality amp that was produced only
on special order, and was known as the overdrive special. With a beautifully
rounded low range, a sharp midrange attack, and a sweet treble register, this
is ideal for single coil pickups.
BOUTIQUE OD
This models the overdrive channel of a 100W high-quality amp that was
produced only on special order, and was known as the overdrive special. The
wonderful sustain obtained by raising the GAIN control is smooth and soulful.
VOX AC30
This is a modeling of the normal channel of AC30, which is a typical guitar
amplier of VOX. The clear high range of the Celestion alnico “Blue” speaker,
as well as the rich midrange, deliver a captivating clean sound.
VOX AC30TB
This models an AC30 amp with the “top boost” circuit of the 1964 AC30. It
delivers a smooth and rened top end, a majestically deep overdrive, and a
rich, brilliant clean sound.
14
BRIT 800
This models a UK-manufactured 100W single-channel head with master
volume made in 1983. Turn the GAIN control all the way up to get the thick,
snarling hard rock and heavy metal sound that dominated the 80’s.
BRIT VM
This models an English-made 100W amp head released in 2007 that boasts
a four-channel design with powerful tone. We’ve used the “Overdrive 2”
channel, which produces a tight low-end and transparent high-gain metal
sound.
SL-OD
This models the overdrive channel of a snakeskin-covered 100W amp head
built in 1991. With an open low-end and a compressed mid/high range, its
powerful, heavy sound delivers a forceful tone that will not break down even
with the most extreme gain settings.
DOUBLE REC
This models the modern high-gain channel from a wild beast of an amp.
Its deep and loose low-end, sparkling highs, and monstrous gain are ideal
for guitars tuned as low as possible, or for metal acts wielding seven-string
guitars.
VOCODER
When you sing or speak into the microphone while playing the guitar, the
talking modulation effect is activated, which makes it sounds as if the guitar
is singing. This is effective when you speak clearly while changing your voice.
[TIP] When the microphone is not connected, talking modulation is applied in
connection with guitar picking.
LINE
Only a tone control amplier that produces a clean tone. This works best
with audio signal input from a line-level instrument like an electric acoustic
guitar or keyboard. In the VOX MINI GO 50, the high frequency (HIGH), mid
frequency (MID), and low frequency (LOW) tones are adjusted using the
GAIN, TREBLE, and BASS knobs, respectively. In the VOX MINI GO 3/10, the
high frequency (HIGH) tone is adjusted using the GAIN knob, and the low
frequency (LOW) tone is adjusted using the TONE knob.
EFFECTS 1 (Modulation types/Octave)
CHORUS
A standard chorus effect that gives the sound a sway and rich expanse.
Adjust the modulation speed with the knob.
PHASER
A phaser effect that creates a cyclical swell. Adjust the modulation speed
with the knob.
TREMOLO
A typical tremolo that modulates the volume up and down cyclically.
OCTAVE
An effect that adds a bass sound that is one octave lower. You can adjust the
knob to achieve a subtle octave or one that is fully present, and increasing
the knob further provides synth bass sound with good resonance.
If you play multiple strings at the same time, it may cause a malfunction, so
play with a single note.
EFFECTS 2 (Delay/Reverb types)
A.DLY
This models an analog delay that uses a Bucket Brigade Device (BBD).
Its audio quality is lo-, but it is popular for its warm sound. Adjust the mix
amount of the delay sound with the knob. Set the delay time with the TAP
button. The maximum delay time is approximately 1.45 seconds.
D.DLY
This creates a clear sound delay unique to digital systems. This is effective
for rhythmic play that matches the delay time to the tempo of the song. The
usage of knobs or buttons and the maximum delay time are the same as
A.DLY.
SPRING
This simulates the spring reverb that’s built into many guitar amps. Adjust
the mix amount of the reverb sound with the knob. Set the reverb time with
the TIME button (13).
The reverb time is about four times the interval at which the TIME button is
pressed.
15
HALL
This models the reverberation of a concert hall containing numerous echo
components. The operation of the knob and button is the same as with
SPRING.
Troubleshooting
The power does not turn on even when the power button is pressed
and held down.
• Is the AC adapter cord connected to the rear panel of the amp correctly?
• Is the AC adapter plugged into an AC outlet?
• Is the AC outlet switched on and working?
• Is the AC adapter damaged?
If you are using a mobile battery:
• Is the mobile battery charged?
• Has it been a while since you connected the mobile battery?
If no power is consumed after a while, the mobile battery may stop operating
and may not turn on even if you press and hold the power button on the unit.
Press the power button on the mobile battery, or disconnect and reconnect
the USB cable.
• Did you connect the USB cable slowly?
If you connect it slowly or stop midway, it may not be recognized correctly.
Quickly insert it all the way.
There’s no sound coming from the amp
• Is your guitar turned up?
• Are both ends of your guitar cable plugged into where they should be?
• Is your guitar cable working?
• Are the top panel VOLUME and GAIN knobs turned up?
• Do you have headphones or anything else plugged into the amp’s top panel
PHONES jack?
If “yes,” unplug!
• Is the amplier model VOCODER selected with the microphone connected
to MIC IN?
VOCODER does not produce sound unless data is input to both MIC IN and INPUT.
The amp doesn’t seem very loud
• Is your guitar turned up?
• Is the top panel VOLUME or GAIN knob turned down low?
• Are you using a mobile battery?
Use a mobile battery with an output of at least 1.5A. Depending on the
mobile battery or USB Type-C used, the power may not be turned on, or the
battery may not be able to provide sufcient power.
The rhythm sound is not output
• Is the rhythm section LEVEL knob set to a low value?
• Did you switch mute on by operating the foot switch?
The rhythm tempo changes arbitrarily.
• Are you using the rhythm simultaneously with the looper?
If the rhythm is played back during loop playback, the rhythm tempo is
automatically set based on the rhythm tempo before playback and the length
of the recorded phrase.
Looper recording is not possible.
• Are you trying to record a rhythm or an input from AUX IN?
The rhythm sound and the input from AUX IN are not recorded in the looper.
There’s no looper playback sound.
• Is the LOOP LEVEL knob set to a small value?
• Is foot switch operation muted?
• Was the GAIN knob or VOLUME knob reduced during looper recording?
No sound is output from the microphone connected to the MIC IN
terminal.
• Is the microphone connected correctly?
• Is the microphone switch turned off?
• Is the TRIM knob set to a small value?
• Is the amplier model VOCODER selected with the microphone connected
to MIC IN?
16
VOCODER does not produce sound unless data is input to both MIC IN and INPUT.
No effect is applied.
• Is the tuner function turned on?
When the tuner function is turned on, Effect 1 is bypassed. Press the
VARIATION button to turn the tuner off.
• Is the EFFECTS knob set to the OFF position or a small value?
• If Effect 2 is not applied to the microphone, is the SEND knob set to a small
value?
• Did you turn the effect off by operating the foot switch?
The function of the foot switch changes arbitrarily.
• Are you operating the top panel while pressing the foot switch?
Operate the top panel and foot switch separately, except when changing the
foot switch function.
[TIP] To prevent a function from being changed unintentionally, you can disable
the function change operation during normal operation (refer to "Foot Switch
Function Setting mode).
The function of the foot switch cannot be changed.
• Did you disable function change during normal operation in the foot switch
function setting mode? (Refer to “Foot Switch Function Setting mode” on
Page page 11)
Specications
(VMG-3/10/50 = VOX MINI GO 3/10/50)
Number of amp types: 11
Number of effects: 8
Number of program: 3 (VMG-50 only)
Number of rhythm patterns: 33
Tempo: 40-240BPM
Looper Recording Time: 0.25-45 sec. (VMG-10/50 only)
Tuner range: E1-E6 (41.2Hz – 1318.5Hz)
Input/Output jacks: INPUT, MIC IN, AUX IN, PHONES, FOOT SW (VMG-10/50 only)
Power amp output:
VMG-3 Maximum approx. 3W RMS@4 ohms
VMG-10 Max approx. 10W RMS@16 ohms
VMG-50 Max approx. 50W RMS@4 ohms
Speaker:
VMG-3 5 inch 4 ohms
VMG-10 6.5 inch 16 ohms
VMG-50 8 inch 4 ohms
Power supply: Included AC adapter or USB mobile battery
Battery life with the 10000 mAh mobile battery used (approximate)
VMG-3: approx. 12 hours / VMG-10: approx. 6 hours / VMG-50: approx. 3 hours
Current consumption:
VMG-3/VMG-10 1A
VMG-50 3.42A
(when using the AC adapter; max. 5V/3A when using a mobile battery)
Dimensions (W x D x H):
VMG-3 256 x 180 x 249 mm/10.08 x 7.09 x 9.80 inches
VMG-10 296 x 210 x 294 mm/11.65 x 8.27 x 11.57 inches
VMG-50 390 x 250 x 358 mm/15.35 x 9.84 x 14.09 inches
Weight:
VMG-3 3.5 kg/7.72 lbs
VMG-10 4.5 kg/9.92lbs
VMG-50 7.3 kg/16.09 lbs
Included Items: Quick Start Guide, AC adapter (VMG-3/VMG-10 DC 12V, VMG-50 DC 19V), strap
Accessories (option): VOX VFS3 Foot switch
17
Fr
Introduction
Merci d’avoir choisi l’amplicateur de guitare à modélisation portable
MINI GO 3/10/50 de VOX. An de pouvoir exploiter au mieux toutes les
possibilités offertes par l’instrument, veuillez lire attentivement ce manuel.
Caractéristiques principales
11 types d’amplis
L’amplicateur est doté de 9 sons d’amplication utilisant la technologie de
modélisation “VET”, ainsi qu’un réglage de vocodeur et un réglage de ligne
pour guitares acoustiques électriques ou claviers.
Effets disponibles
L’amplicateur est doté de huit effets de haute qualité: quatre effets de
retard et réverbération, trois effets de modulation et un effet d’octave.
Fonction rythmique
Comprend 33 types de motifs rythmiques avec un large éventail de variations.
Fonction d’accordeur
Vous pouvez accorder la guitare ou la basse connectée à la borne INPUT.
Fonction looper (VOX MINI GO 10/50)
Propose une fonction looper simple et conviviale, qui peut être utilisée en
même temps que la fonction rythmique.
Fonctionnement sur batteries portables
Des batteries portables disponibles dans le commerce peuvent être utilisées
comme source d’énergie.
Utiliser avec un microphone ou un lecteur audio
La section d’entrée propose, entre autres, une prise AUX IN pour une source
audio externe (lecteur CD, MP3 etc.) et une prise MIC IN pouvant accueillir un
microphone. Ainsi, vous pouvez vous faire accompagner par votre musique
favorite ou chanter tout en jouant de la guitare.
Fonctionnement avec une pédale interrupteur
(VOX MINI GO 10/50)
En connectant une pédale interrupteur VFS3 (en option), vous pouvez
manipuler les fonctions rythmiques et looper à l’aide de votre pied.
Parties et leurs fonctions
Face avant
Section d’entrée
1. Prise INPUT
C’est ici que vous branchez votre guitare.
2. Prise MIC IN
Connectez le microphone (microphone dynamique).
3. Commande TRIM
Cette commande règle le niveau d’entrée du micro.
4. Commande SEND
Réglez le volume envoyé par l’entrée MIC à l’effet 2 (retard/
réverbération).
Non disponible lorsque le sélecteur AMP est réglé sur
VOCODER.
Section AMP
Cette section permet d’effectuer divers réglages liés à l’amplicateur.
5. Sélecteur AMP
Ce sélecteur permet de sélectionner un modèle d’ampli (pour plus de détails,
voir “Modèle d’ampli” à la page 26). Le circuit de gain, les caractéristiques de
contrôle du timbre et l’agencement des circuits sont automatiquement réglés en
fonction du modèle d’ampli sélectionné. Vous pouvez également sélectionner le
modèle d’amplicateur ou le vocodeur approprié pour l’entrée LINE.
6. Commande GAIN
Cette commande règle le gain du préampli du modèle sélectionné.
1
2
3
4
5
6
7
8 9
10
5
VOX MINI GO 3
VOX MINI GO 10
7b
18
7. Commande TREBLE (VOX MINI GO 50 uniquement)
Permet de régler la tonalité dans les aigus. Le timbre change
automatiquement selon le modèle d’ampli sélectionné.
7b. Commande TONE (VOX MINI GO 3/10)
Permet de régler la tonalité. Le timbre change automatiquement selon le
modèle d’ampli sélectionné.
8. Commande BASS (VOX MINI GO 50 uniquement)
Permet de régler la tonalité dans les basses. Le timbre change
automatiquement selon le modèle d’ampli sélectionné.
9. Sélecteur de puissance (VOX MINI GO 10/50)
Ce sélecteur permet de régler la puissance de sortie de l’amplicateur.
Cet interrupteur n’affecte pas la sortie PHONES.
10. Commande VOLUME
Permet de régler le niveau de sortie du préamplicateur.
Section des effets
Cette section permet de régler les effets. Pour en savoir plus sur les
effets, voyez la section “Effets 1”,“Effets 2” à la page 27.
11. Commande EFFECTS 1
Réglez la position de la commande pour commuter
l’effet 1 (modulation/octave) et dénissez la
profondeur d’un effet. Pour ignorer les effets, tournez
la commande à fond vers la gauche.
12. Commande EFFECTS 2
Réglez la position de la commande pour passer à l’effet
2 (retard/réverbération) et dénissez la profondeur d’un
effet. Pour contourner les effets, tournez la commande
à bout de course vers la gauche.
13. Bouton et diode TIME
Ce bouton permet de régler la durée de l’effet 2
(retard/réverbération). Tapez deux fois sur ce bouton
pour régler la durée voulue. La diode clignote en
synchronisation avec l’heure.
11 12 13
Section des RHYTHM
14. Sélecteur Genre
Ce sélecteur permet de choisir un genre de
motif rythmique.
15. Bouton et diode VARIATION
Vous avez le choix entre neuf variations pour
chaque genre (voyez p.21 “Utilisation de la
section rythmique”).
Pour activer l’accordeur, maintenez le bouton
VARIATION enfoncé Durant plus d’une seconde.
(voyez p.23 “Utiliser l’accordeur”)
16. Bouton TEMPO
Réglez le tempo du rythme. Appuyez sur
ce bouton deux fois pour régler le tempo.
La durée entre deux pressions sera utilisée
comme valeur de tempo.
17. Commande RHYTHM LEVEL
Détermine le volume du motif rythmique.
18. Bouton RHYTHM START/STOP
Lance/arrête le motif rythmique.
Section looper (VOX MINI GO 10/50)
Effectuez les opérations et les réglages du
looper. Pour plus de détails sur l’utilisation
du looper, consultez “Utiliser la fonction
looper (VOX MINI GO 10/50)” à la p.21.
19. Commande LOOP LEVEL
Utilisé pour régler le volume pendant la
lecture en boucle.
20. Bouton et diode LOOP
Effectuez les opérations telles que
l’enregistrement en boucle, la lecture et
l’effacement.
14 15 16
17 18
19
20
19
Section programme (VOX MINI GO 50 uniquement)
21. Bouton et diode PROGRAM
Appuyez sur ce bouton pour choisir un programme.
À chaque appui sur le bouton PROGRAM, la diode
PROGRAM devient verte
orange rouge s’éteint. (Voir
"Programmes d’usine et programmes utilisateur" à la page
23.) Ce bouton sert aussi à mémoriser vos programmes
perso. (Voir "Mémoriser un programme" à la page 23.)
Section alimentation/AUX IN/PHONES
22.
Bouton et diode (Interrupteur d’alimentation)
Maintenez cet interrupteur enfoncé pour mettre l'ampli
sous tension et hors tension. La diode d'alimentation
s'allume quand l'ampli est mis sous tension.
La couleur de la diode d’alimentation varie selon le type
d’équipement d’alimentation connecté (courant maximum
pouvant être consommé par cet instrument).
Vert: S’allume lorsque le courant de 3 A maximum peut
être utilisé en connectant l’adaptateur secteur
fourni avec ce produit à la borne DC 19V (borne
DC 12V pour VOX MINI GO 3/10) ou par la batterie
connectée à la borne DC 5V IN.
Orange: S’allume lorsque le courant de 1,5 A maximum
peut être utilisé selon l’équipement connecté à la
borne DC 5V IN.
23. Prise AUX IN
Branchez la sortie analogique d’une source audio à cette prise. Vous pouvez
y brancher un lecteur audio et accompagner vos morceaux favoris à la guitare
ou encore travailler des solos.
24. Prise PHONES
Cette prise permet de relier directement l’ampli à l’entrée d’une console,
d’un enregistreur, etc. Vous pouvez aussi y brancher un casque d’écoute. Le
signal présent à cette prise est aussi traité par le modèle d’enceinte.
La connexion d’un casque à cette prise désactive le haut-parleur interne.
Veillez à établir une connexion stéréo à la prise PHONES.
19
20
22
23
24
21
Face arrière
25. Barre de protection de connecteur (VOX MINI GO 10/50)
N’utilisez pas cette barre de protection pour transporter cet instrument. Pour
transporter l’instrument, utilisez la courroie de transport fournie avec ce
produit.
26. Prise DC 19V* (*Prise DC 12V sur VOX MINI GO 3/10)
Branchez ici l’adaptateur fourni.
L’adaptateur secteur est uniquement destiné à alimenter cet ampli. Ne l’utilisez
jamais pour alimenter d’autres appareils car cela pourrait causer un
dysfonctionnement.
27. Prise DC 5V IN (connecteur USB de type C)
Connectez une batterie de téléphone portable disponible dans le commerce.
Du bruit peut être entendu lorsque l’alimentation est fournie par un
adaptateur secteur USB disponible dans le commerce, utilisez donc une
batterie mobile.
Cette borne est uniquement utilisée pour l’entrée. Elle ne peut pas alimenter
un autre dispositif.
Non compatible avec l’alimentation USB (USB PD).
28. Prise FOOT SW (VOX MINI GO 10/50)
Connectez la pédale-interrupteur dédiée VFS3. Pour plus de détails,
reportez-vous à la section “Utiliser la pédale-interrupteur” à la page 24.
2625 27
28
VOX MINI GO 3VOX MINI GO 50
26 27
21
20
Préparation
1. Réglez la commande VOLUME (10), la commande TRIM (3) et la commande
RHYTHM LEVEL (17) sur le niveau minimum.
2. Reliez l’adaptateur secteur fourni à la prise DC 19V (prise DC 12V pour
VOX MINI GO 3/10) sur la face arrière (26) et l’autre extrémité à une prise
de courant.
Pour utiliser une batterie portable disponible dans le commerce,
connectez-la à la prise DC 5V IN (27) à l’aide d’un câble USB de type C.
Utilisez une batterie portable avec une sortie d’au moins 1,5 A. Selon la
batterie mobile ou l’USB de type C utilisé, il se peut que l’alimentation ne
soit pas activée ou que la batterie ne puisse pas fournir une puissance
sufsante.
Lors de l’utilisation d’une batterie portable, il se peut qu’une distorsion de la
sortie se produise ou qu’il y ait du bruit.
3. Branchez votre guitare à la prise INPUT en face avant.
Si vous comptez utiliser un lecteur CD ou MP3, voire un
microphone, relies le lecteur à la prise AUX IN ou le
microphone à la prise MIC IN en face avant.
4. Maintenez le bouton d’alimentation enfoncé jusqu’à ce
que la diode d’alimentation s’éteigne et que l’ampli soit
sous tension.
5. Réglez le volume avec la commande VOLUME.
6. Pour mettre l’ampli hors tension, maintenez son bouton
d’alimentation enfoncé jusqu’à ce que la diode
d’alimentation s’éteigne.
Utilisation du support (VOX MINI GO 10/50)
Le VOX MINI GO 10/50 peut être réglé en
biais en tirant sur les deux supports situés en
bas de l’unité principale (voir gure de
gauche).
Veillez à installer le support sur une surface
plane. Si vous placez le support en biais sur
une pente, il risque de tomber.
N’appliquez pas de charge excessive, par
exemple en vous appuyant sur l’amplicateur.
Fonction de coupure automatique d’alimentation
La fonction de coupure automatique d’alimentation met automatiquement
l’amplicateur hors tension lorsqu’il n’est pas utilisé ou lorsqu’aucun son
n’est émis pendant environ une heure. Une fois l’alimentation de l’ampli
coupée par cette fonction, l’appareil reste hors tension et ne répond à
aucune manip. Pour utiliser à nouveau l’ampli, remettez-le sous tension.
La fonction de coupure automatique d’alimentation ne fonctionne pas
pendant la lecture du rythme ou le fonctionnement du looper (pendant
l’enregistrement, la lecture ou l’overdub).
Si le volume ou la variation du son de sortie est extrêmement faible, la
fonction de coupure automatique d’alimentation peut être activée. En outre,
selon les paramètres et l’environnement, la fonction de coupure automatique
d’alimentation peut ne pas être activée en raison du bruit, même si vous ne
jouez pas.
Réglage de la fonction de coupure automatique d’alimentation
1.
Maintenez le bouton TEMPO (16) enfoncé tout en mettant l’ampli sous tension.
2. La diode VARIATION (15) indique le réglage actif.
Activé
Désactivé
3. Appuyez sur le bouton TEMPO (16) pour activé et désactivé
alternativement la fonction de coupure automatique d’alimentation.
4. Attendez quelques secondes sans manipuler aucun bouton ni commande.
L’ampli passe alors en mode de fonctionnement normal.
Le réglage de la fonction de coupure automatique d’alimentation est
mémorisé et conservé même quand vous mettez l’ampli hors tension.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
dans d''autres langues
- English: Vox MINI GO Owner's manual
- español: Vox MINI GO El manual del propietario
- Deutsch: Vox MINI GO Bedienungsanleitung
- 日本語: Vox MINI GO 取扱説明書
Documents connexes
-
Vox MINI GO Guide de démarrage rapide
-
-
-
-
-
Vox MINI3 G2 Le manuel du propriétaire
-
-
-
-
Autres documents
-
Boss RC-30 Dual Track Looper Le manuel du propriétaire
-
Korg WAVEDRUM Mini Le manuel du propriétaire
-
-
Korg PANDORA PX5D Le manuel du propriétaire
-
-
Yamaha PSR-SX700 Digital Workstation Manuel utilisateur
-
Ibanez TB50R Le manuel du propriétaire
-
-
-
Fender 2314400000 Acoustic Junior GO Guitar Amplifiers Le manuel du propriétaire