TEAC Esoteric X-01 Manuel utilisateur

Marque: TEAC

Modèle: Esoteric X-01

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Ce manuel convient également à

D00816700B

Super Audio CD/CD Player

Owner’s Manual ....................2

Manuel du Propriétaire

...........23

Bedienungsanleitung

..............44

CAUTION

DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS

ARE WITHIN!

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Do not expose this apparatus to drips or splashes.

< Do not place any objects filled with liquids, such as vases, on the

apparatus.

Do not install this apparatus in a confined space such as a book

case or similar unit.

The apparatus draws nominal non-operating power from the AC

outlet with its POWER switch in the off position.

The apparatus should be located close enough to the AC outlet

so that you can easily grasp the power cord plug at any time.

An apparatus with Class

construction shall be connected to an

AC outlet with a protective grounding connection.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Changes or modifications to this equipments not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

For U.S.A.

ENGLISH

Optical pickup :

Type : GH20707A2A

Manufacturer : SHARP CORPORATION

Laser output : Less than 1mW on the objective lens

Wavelength : 788±5 nm (CD)

For U.S.A.

①

Contents

Thank you for choosing TEAC. Read this manual carefully

to get the best performance from this unit.

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Restoring factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front panel features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Understanding the remote control unit . . . . . . . . . . . . . . . . . . 11

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Skipping playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Selecting a track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Fast scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Selecting the playback area. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Programmed playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Repeat mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Display dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Analog sound output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Changing the display mode . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Clock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Settings (introduction). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Audio Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on

the Radiation Control for Health and Safety Act of 1968“, and is

classified as class 1 laser product. There is not hazardous invisible

laser radiation during operation because invisible laser radiation

emitted inside of this product is completely confined in the

protective housings.

The label required in this regulation is shown

①.

For European customers

Disposal of your old appliance

1.When this crossed-out wheeled bin

symbol is attached to a product it means

the product is covered by the European

Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of

separately from the municipal waste stream via designated

collection facilities appointed by the government or the

local authorities.

3. The correct disposal of your old appliance will help prevent

potential negative consequences for the environment and

human health.

4. For more detailed information about disposal of your old

appliance, please contact your city office, waste disposal

service or the shop where you purchased the product.

The world’s first VRDS mechanism for Super

Audio CD players, incorporating a magnesium

turntable and a SS400 bridge

The VDRS mechanism completely eliminates any vibration of

the disc itself, thanks to the full-diameter clamp, which

clamps the disc securely to the turntable. In addition, warping

and other defects of the disc are eliminated. The constancy of

the reading angle between the optical pickup and the disc

pits is therefore increased, and read errors, together with the

occurrence of timing errors to the clock circuit, are

significantly reduced.

Playback of Super Audio CDs requires high-speed rotation and

a high degree of precision, and the X-01 accordingly uses a

magnesium turntable. This has only two-thirds the specific

gravity of aluminum and has excellent shock-absorbent

properties. The bridge employs a pair of precisely engineered

ball bearings, and is constructed of SS400 steel, mounted

directly on the 5mm thick steel base plate.

Coreless motor with neodymium magnets

A newly-developed three-phase brushless spindle motor

provides the fast and accurate turntable rotation required for

Super Audio CD playback. This, and the fixing of the

turntable together with the use of precision ball bearings,

eliminate irregular rotation and vibration.

Research has shown that neodymium is the optimum

magnetic material for this application. Neodymium absorbs

changes to the motor’s electric power supply, and exerts

minimal influence on the audio sections of the unit.

Constant-angle optical pickup mounted on a

sled with feedback-monitored speed control

By mounting the pickup on a sled whose axis is rigid, the

pickup lens is maintained at a constant angle and the laser

beam, and hence the optical axis, is maintained in an accurate

vertical orientation. An Esoteric original three-phase brushless

motor with Hall element detection drives the sled, and the

speed of the sled is monitored and used to control the sled

itself in a servo feedback operation, meaning the sled is highly

responsive and smooth in its operation.

Sturdy, rigid chassis with triple-point

pinpoint foot support

The unit is constructed with a 5mm thick robust steel base

plate, and is divided into three logical sections, thereby

reducing interference between components of the unit.

Highly rigid mounts are used for the VDRS disc mechanism.

To eliminate vibration, three solid (tool steel) feet support the

unit and isolate it mechanically.

Brushed aluminum finish exemplifies the

quality of construction

The front, side and top panels are constructed of thick

brushed aluminum. The high-quality luxurious finish matches

the overall attention to the finest possible quality, shown in

such details as the illuminated surrounds to the control

buttons, the milled top-panel logo, and the milled aluminum

disc tray.

Unsurpassed design and features

The X-01 is truly the most advanced Super Audio CD player to

date. Separation of power supplies for each major function

(digital audio, DAC circuitry, analog audio) ensures total

fidelity. The DACs have sub-ground impedances with

exceptional S/N figures. Full 5.1 surround Super Audio CD

playback is possible with the X-01.

Audio DACs

All audio channels use Burr-Brown 24-bit DA converters

(PCM1704). Improved linearity is achieved for the two front

channels by the use of 4-tip-converter for each channel.

The audio DAC boards employ a high-quality quartz crystal,

which results in the almost complete elimination of jitter and

subsequent high-quality DA conversion.

Word synchronization

A master word clock from a high-quality DA converter or

master clock generator can be used for clock synchronization,

resulting in the almost complete elimination of jitter.

Using a high-quality clock signal provided by an external DA

converter such as the Esoteric G-0/G-0s provides optimum

video and audio quality, up to 192kHz, optimizing a top-

ranking universal player like the X-01.

Features

ENGLISH

What’s in the box

Please confirm that the following accessories are in the box

when you open it.

Remote control unit x 1

Batteries (AA, R6, SUM-3) x 2

Felt sheet x 3

Power cord x 1

Owner’s manual x 1

Warranty card x 1

Conventions about This Manual

< Instructions in this manual describe the controls on the

remote control. You can also use the buttons on the front

panel if they have the same or similar names as those on the

remote.

The types of functions and operations that can be used for a

particular disc vary depending on the features of that disc. In

some cases, these functions and operations may differ from

the descriptions given in this Owner’s Manual.

The drawings about the front panel display used in this

Owner’s Manual are purely for the purposes of explanation.

The actual displays may differ slightly from what are shown

here.

Read this before operation

< As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding

this matter, consult an electrician.

Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Also

avoid locations subject to vibrations and excessive dust, heat,

cold or moisture.

Do not place the unit on the amplifier/receiver.

Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into

the unit, contact your dealer or service company.

When removing the power plug from the wall outlet, always

pull directly on the plug, never yank the cord.

To keep the laser pickup clean, do not touch it, and always

close the disc tray.

Do not attempt to clean the unit with chemical solvents as

this might damage the finish. Use a clean, dry cloth.

Keep this manual in a safe place for future reference.

DO NOT MOVE THE UNIT DURING PLAYBACK

During playback, the disc rotates at high speed. Do NOT lift or

move the unit during playback. Doing so may damage the

disc or the unit.

WHEN MOVING THIS UNIT

When changing places of installation or packing the unit for

moving, be sure to remove the disc and return the disc tray to

its closed position in the player. Then, press the power switch

to turn the power off, and disconnect the power cord.

Moving this unit with the disc loaded may result in damage to

this unit.

Before Use

Placement of the unit

High-quality hardened tool steel is used for the pin-point feet,

securely attached to the bottom of the player. Although the

cover feet may appear loose, the weight of the unit causes them

to be firm and secure, and the design effectively damps and

reduces vibration.

Be careful to avoid injury when moving the unit, on account

of its weight. Get someone to help you if necessary.

< To protect floors, etc. you may stick the felt supplied with the

unit to the bottom of the cover feet.

Pin-point foot

Bottom plate

of the unit

Steel foot

Cover foot retaining screws

Cover foot

CAUTION

The product shall not be exposed to dripping or splashing and

that no object filled with liquids, such as vases, shall be placed

on the product.

Do not install this equipment in a confined space such as a

book case or similar unit.

Beware of condensation

When the unit (or a disc) is moved from a cold to a warm place,

or used after a sudden temperature change, there is a danger of

condensation; vapor in the air could condense on the internal

mechanism, making correct operation impossible. To prevent

this, or if this occurs, leave the unit for one or two hours with

the power turned on. Then the unit will stabilize at the

temperature of its surroundings.

Maintenance

If the surface of the unit gets dirty, wipe with a soft cloth or use

diluted neutral cleaning liquid. Be sure to remove any fluid

completely. Do not use thinner, benzine or alcohol as they may

damage the surface of the unit.

Discs

Audio CD:

• 12cm or 8cm discs

• Linear PCM digital audio

Audio CDs are divided into tracks.

Super Audio CD:

• Single layer, dual layer or Hybrid layer

• 12cm or 8cm discs

• Digital audio (DSD)

Super Audio CDs are divided into tracks.

Type of Discs That Can be Played on This

System

This player can playback discs bearing any of the following logos:

“Super Audio CD” is a registered trademark. “DSD” is a registered trademark.

About CD-R/CD-RW

CD-R/RW discs recorded in Audio CD format and finalized

correctly are playable. But depending on the quality of the

disc and/or the condition of the recording, some CD-R & CD-

RW discs may not be playable.

Caution:

If you record a disc using a personal computer, even if it is

recorded in a compatible format, there are cases in which it

may not play because of the settings of the application

software used to create the disc. (Check with the software

publisher for more detailed information.)

Unfinalized CD-R/CD-RW discs cannot be played.

Following discs cannot be played with this

unit:

• DVD, CD-G, Data part of CD-EXTRA, PHOTO CD, CD-ROM

and DVD-ROM discs

• discs recorded in a color system other than PAL or NTSC

• illegally produced discs

• scratched discs

• discs that are dusty, soiled or marked with fingerprints

Warning:

If you attempt to play back such discs, there is a risk that sudden

loud noise can blast over the speakers at full volume and cause

damage to the speakers and your hearing.

Copy-protected discs and other discs which do not conform to

the CD standard may not play back correctly in this player. If you

use such discs in this unit, TEAC Corporation and its subsidiaries

cannot be responsible for any consequences or guarantee the

quality of reproduction. If you experience problems with such

non-standard discs, you should contact the producers of the

disc.

How to remove the disc How to hold the disc

< Always place the disc on the disc tray with the label side

uppermost. (Compact discs can be played or recorded only on

one side.)

To remove a disc from its storage case, press down on the

center of the case and lift the disc out, holding it carefully by

the edges.

Should the disc become dirty, wipe the surface radially (from

the center hole outward towards the outer edge) with a soft,

dry cloth:

Never use such chemicals as record sprays, antistatic sprays or

fluid, benzine or thinner to clean the discs. Such chemicals

will do irreparable damage to the disc’s plastic surface.

Discs should be returned to their cases after use to avoid dust

and scratches that could cause the laser pickup to “skip.”

Do not expose discs to direct sunlight or high humidity and

temperature for extended periods. Long exposure to high

temperatures will warp the disc.

Do not play any disc that is warped, deformed or damaged.

Playing such discs may cause irreparable harm to the playing

mechanisms.

CD-R and CD-RW discs are more sensitive to the effects of

heat and ultraviolet rays than ordinary CDs. It is important

that they are not stored in a location where direct sunlight

will fall on them, and which is away from sources of heat

such as radiators or heat-generating electrical devices.

Printable CD-R and CD-RW discs aren’t recommended, as the

label side might be sticky and damage the unit.

Do not stick papers or protective sheets on the discs and do

not use any protective coating spray.

Use a soft oil-based felt-tipped pen to write the information

on the label side. Never use a ball-point or hard-tipped pen,

as this may cause damage to the recorded side.

Never use a stabilizer. Using commercially available CD

stabilizers with this unit will damage the mechanisms and

cause them to malfunction.

Do not use irregular shape CDs (octagonal, heart shaped,

business card size, etc.). CDs of this sort can damage the unit:

If you are in any doubt as to the care and handling of a CD-

R/CD-RW disc, read the precautions supplied with the disc, or

contact the disc manufacturer directly.

ENGLISH

Remote Control Unit

Battery Replacement

If the distance required between the remote control unit and

main unit decreases, the batteries are exhausted. In this case

replace the batteries with new ones.

Precautions concerning batteries

Be sure to insert the batteries with correct positive “+” and

negative “_

” polarities.

Use batteries of the same type. Never use different types of

batteries together.

Rechargeable and non-rechargeable batteries can be used.

Refer to the precautions on their labels.

When the remote control unit is not to be used for a long

time (more than a month), remove the batteries from the

remote control unit to prevent them from leaking. If they

leak, wipe away the liquid inside the battery compartment

and replace the batteries with new ones.

Do not heat or disassemble batteries and never dispose of old

batteries by throwing them in a fire.

Notes on use

Point the remote control unit at the player’s remote sensor

and use it within seven meters’ distance of the player. There

should not be any obstacles between the player and the

remote control unit.

Do not allow direct sun or other light to shine on the remote

sensor part of the player. This may cause the remote control

unit to work incorrectly.

Note that other units with remote controls may operate

incorrectly because of infrared light “overspill” when you

operate this remote control unit.

How to insert the batteries

Remove the cover of the remote control unit with a

screwdriver. After checking the polarity (+

/_) of two AA

batteries, insert the batteries, replace the cover and replace

the screws.

If you have made a lot of changes to the setup, and want to

restart from a known set of options, restore the unit to the

factory settings as follows:

1. With the unit turned off, press and hold down the STOP

button.

2.While holding down the STOP button, press the POWER

switch.

All memories are erased, and the unit returns to the factory

settings.

Restoring factory settings

WORD SYNC OUT

5.1CH AUDIO IN

FRONT SURROUND

SUBWOOFER

CENTER

DIGITAL IN (COAXIAL)

DIGITAL IN (OPTICAL)

AUDIO IN

A C

Connections

CAUTION:

Switch off the power to all equipment before making connections.

Read the instructions of each component you intend to use with this unit.

Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the

signal interconnection cables together with the AC power cord or speaker cables.

RCA cable

RCA coaxial cable

optical digital cable

BNC coaxial cable

XLR cable

Balanced XLR

pin assignment

Stereo amplifier

Master clock generator (G-0s, etc.)

D/A Converter

Surround amplifier

Digital audio device

(CD recorder, MD deck, etc.)

Supplied power cord

Wall socket

ENGLISH

Analog audio output terminals

Use either the XLR or RCA (pin) FRONT terminals for analog

stereo output.

If your amplifier has balanced XLR analog audio inputs,

connect the XLR jacks on the unit to the amplifier’s XLR

jacks, otherwise use the RCA (pin) connections.

For surround (5.1) amplifiers with analog inputs, also use the

RCA (pin) SURROUND pair, CENTER and SUBWOOFER

connections (in addition to the FRONT pair).

If you are connecting only 2 channels, use the 2CH/MULTI

button on the remote control to select “2 ch”. For surround

sound with six speakers connected, you can select either

“2ch” or “5.1 ch” mode. Note that if multi-channel

program material is played and 2-channel mode is selected,

the multi-channel material will be downmixed to two

channels, and output through the L and R front outputs.

Digital audio output terminals

The unit may be connected using either coaxial or optical

(TOS) commercially available cables to amplifiers or to digital

audio devices such as CD recorders, etc.

COAXIAL: Use RCA (pin) digital audio cable

OPTICAL: Use optical digital audio cable (TOS)

The optical terminal is covered by a shutter. Make sure that

the cable is firmly inserted, but do not force the cable when

connecting it or removing it, in order not to cause damage

to the unit.

Application notes

The unit does not output digital surround sound from Super

Audio CDs, so to enjoy surround sound from these media, you

must make analog connections to a suitably equipped

surround sound amplifier.

Word sync connector

This allows the use of an externally-generated word clock

connection, using a commercially available BNC coaxial

cable.

Devices producing such a suitable clock signal include

external D-A converters, or dedicated word clock

generators. Connect the SYNC OUT (or WORD OUT) of such

a device to the unit.

Digital output expansion slot

This slot is reserved for a future upgrade, which will allow

the output of Super Audio CD data in digital format.

SIGNAL GND connection

Use a commercially available PVC-covered cord to connect

the signal ground terminal on the unit to the amplifier signal

ground.

Note that this is NOT an electrical safety ground (earth).

Power cord receptacle

After all other connections have been made, insert the

supplied AC power cord into this receptacle, then connect

the other end of the power cord into the wall socket. Ensure

that your AC voltage corresponds to the voltage marked on

the rear panel of the unit. Consult a qualified electrician if

you are in doubt.

In order to avoid the risk of electric shock, fire, and so on,

only use the supplied power cord.

If you are not going to use the unit for some time,

disconnect the power cord from the wall socket.

Front panel features

Disc type indicator

Shows the type of disc currently loaded.

TRACK indicator

Indicates that the track number of a CD or Super Audio CD is

being shown.

TOTAL indicator

Indicates that the total time is being shown.

REMAIN indicator

Indicates that the remaining time is being shown.

DOWN MIX indicator

Lights to show that a multi-channel source has been

downmixed to the analog outputs.

5.1CH indicator

Lights to show that 5.1 analog output has been selected

Channel indicators

Light to show which surround channels are currently in use.

Message area

Alphanumeric display to show times, titles, status messages,

etc.

REPEAT indicator

Lights when repeat play is selected

Pause indicator

Lights when playback is paused.

Playback indicator

Lights when playing back.

The equipment draws nominal non-operating power from

the AC outlet with its POWER switch in the OFF position.

A B C D E G H I JF

Front Panel

POWER

Use this to turn the unit on and off. When the unit is on, the

ring surrounding the button lights up.

CLOCK MODE

Use this to select an external word sync source connected to

the WORD SYNC connector on the rear panel.

Remote control sensor

Receives signals from the remote control unit. Point the

remote control unit at this sensor when operating the remote

control unit.

Display

Disc tray

OPEN/CLOSE

Use this to open and close the disc tray.

STOP

Use this to stop playback. When playback is stopped, the ring

surrounding the button lights up.

PLAY

Use this to start playback. When a disc is being played back,

the ring surrounding the button lights up.

PAUSE

Use this to pause playback. When playback is temporarily

paused, the ring surrounding this button lights up.

SKIP (.//)

Use these for skip operations. Pressing and holding these

buttons for more than a second changes the scanning speed.

Display

ENGLISH

Understanding the remote control unit

Number buttons

Use these for selecting tracks by number, etc.

2CH/MULTI

Use this to switch between two-channel (stereo) and multi-

channel surround audio output.

PLAY AREA

Use this to select the playback area of Super Audio CDs.

SCAN (m/,)

Use these for fast scanning during playback.

STOP

Equivalent to pushing the STOP button on the front panel.

PLAY

Equivalent to pushing the PLAY button on the front panel.

Cursor buttons and ENTER

Use these buttons in the setup mode.

SETUP

Use this button to enter or exit the setup menu.

OPEN/CLOSE button

Duplicates the functions of the OPEN/CLOSE button on the

front panel.

Clear button

Use this button to clear entry errors, etc.

DISPLAY

Use this button to change the display mode.

FL DIMMER button

Use this button to change the brightness of the front panel

display.

REPEAT

Use this button to set the repeat playback mode.

PROGRAM

Use this button when programming playback order.

MUSIC SKIP (.//)

These buttons are equivalent to the skip buttons on the front

panel.

PAUSE

This button is equivalent to the PAUSE button on the front

panel.

RETURN

Use this button to go back a level in the setup menu.

Playback

Opening and closing the tray

2 43

Turn on the power using the POWER button on the

main unit.

The button and the display light.

Press the OPEN/CLOSE button.

The tray opens after a second or two (this delay is due to the

movement of the internal mechanism of the unit before

opening).

Insert the disc label side uppermost.

< Make sure the disc is centrally located, in order to avoid any

malfunction or jamming of the tray or the unit.

Press the OPEN/CLOSE button again.

The tray closes. Take care not to trap your fingers in the tray.

The unit reads the disc (this may take a little time).

Press the PLAY button to start playback.

Pausing playback

Press the PAUSE button to pause playback (the ring

surrounding the PAUSE button on the main unit lights).

Press PLAY or PAUSE to restart playback.

Stopping playback

Press the STOP button (the ring surrounding the STOP button

on the main unit lights).

Pressing OPEN/CLOSE opens the tray if it is closed, and closes

it if it is open. When the tray is opened during playback, it

may take a few seconds before the disc is “unloaded” and

the tray opens.

Number of tracks on disc Total disc running time

ENGLISH

Some Super Audio CDs contain two or more separate audio

areas such as multi-channel area, 2 channel area and CD

area.

When playback is stopped, use the PLAY AREA button to

select the playback area.

Selecting the playback area

Skipping playback

Press the MUSIC SKIP button (. or /) repeatedly until

the desired track is found. The selected track will be played

from the beginning.

If the . button is pressed once during playback, playback

returns to the start of the current track. If it is pressed within

one second from the start of the track, playback returns to

the start of the previous track (so pressing the button twice in

quick succession will skip back two tracks, etc.).

If tracks are skipped while playback is paused or stopped,

playback is paused or stopped at the start of the selected

track.

In programmed playback mode, these buttons will move

between tracks in the programmed order.

Selecting a track

Use the number button to select tracks for playback. Use the

+10 button to enter the first digit of numbers greater than 9

(repeated presses show 1-, 2-, 3- etc.) and the single digit

buttons (0 through 9) for the second digit, or single-digit

track numbers.

Playback starts from the selected track, regardless of whether

the number is selected during playback or playback is stopped

or paused.

Use the CLEAR button to clear mistaken entries.

Fast scanning

When playing back, use the SCAN button (m or ,) to

move backwards and forwards. Press PLAY to restart playback

at normal speed at the desired location.

Repeated presses of the SCAN buttons changes the scanning

speeds. There are three speeds:

Fast (1) q

Fast (2) q Fast (3) q Play (normal speed)

You can also use the SKIP buttons of the main unit. To start

scanning (or to change the scanning speed), press and hold

the SKIP button for more than one second.

Notes

Scanning can be carried out across track boundaries.

If backward scanning reaches the start of the disc, playback

starts from the beginning. If forward scanning reaches the

end of the disc, scanning and playback stop.

Programmed playback

Programmed playback allows up to 30 tracks to be played

back in the order you decide.

Press the PROGRAM button (either when playing back

or stopped).

If a track is currently playing back (or paused in the middle of

the track), this track is added as the first item in the

programmed playback list.

Use the number buttons to add tracks to the

programmed playback list.

Use the +10 button and 0 through 9 buttons in exactly the

same way as when selecting tracks.

Continue pressing the number buttons to add tracks.

Clear mistakes with the CLEAR button (the last entry is

cleared)

You can only select tracks on the disc (in other words, if the

disc has six tracks, you cannot program track 7!).

Finish the programming by pressing PLAY.

Programmed playback begins (if the disc is actually being

played back while you are setting the program order, there’s

no need to press PLAY).

Skip between tracks in the programmed playback order using

the SKIP buttons (.

//).

Clearing the last track from the list

Push the CLEAR button to clear the last track from the list.

Adding tracks to the list

Use the number buttons to add tracks to the list.

Clearing the whole program

Press the PROGRAM button to clear the program (playback

continues from the current point).

The OPEN/CLOSE or the POWER button also clears the

program.

Track number Number in programmed list

ENGLISH

Repeat mode

< Halting playback stops the repeat mode.

This feature is not available for all discs.

The following buttons cancel repeat mode:

STOP, OPEN/CLOSE, POWER.

Track repeat

When this is selected, the currently-selected track repeats. If

another track is selected during repeat playback, the newly-

selected track repeats.

Disc repeat

The whole contents of the disc are repeated.

Programmed repeat

If programmed playback has been set up, the whole program

is repeated.

Pushing the REPEAT button cycles between REPEAT PGM

(program repeat) and REPEAT OFF (programmed playback

takes place).

Use the REPEAT button to select the repeat mode for

playback. Repeated presses of the REPEAT button cycle

between the following options:

REPEAT TRK

(track repeat)

REPEAT DSC

(whole disc repeat)

REPEAT OFF

(no repeat)

Display dimming

The display on the main unit can be dimmed to suit the

environment in which you listen to music. There are three levels

and an “off” setting.

Use the FL DIMMER button to cycle between these

settings.

Note that the OFF setting is not memorized when the power is

turned off. When the unit is switched off with the display off,

and then turned on again, the display is reset to the minimum

brightness.

Analog sound output

When playback is stopped, use the 2CH/MULTI button to select

either 2CH (stereo) or MULTI (multi-channel surround) audio

output from the analog outputs.

Note that if multi-channel program material is played and 2-

channel mode is selected, the multi-channel material will be

downmixed to two channels, and output through the L and R

front outputs.

This setting is also reflected on the setup menu.

5.1CH indicator lights when “Multi ch” is selected.

Clock Mode

For highly accurate playback, you can use the word clock

(sync) output of an external unit such as the Esoteric D-70 or

G-0 to synchronize your whole audio system.

Use the CLOCK MODE (main unit) button to switch

between Word M1 ON and Word OFF.

When the unit is synchronizing to the external clock, the ring

surrounding the button flashes. When it is locked, the button

lights.

Note that the sync connection should be made before the

CLOCK MODE button is pressed. If no valid word sync signal

is received, the display shows “No Word!”.

This unit can respond to synchronization signals up to 176.4

kHz, and automatically changes depending on the input

signal.

Mode 1 and Mode 2

When “Word M1 ON” is selected, press the CLOCK

MODE button for more than 3 seconds to switch

between “M1 (mode 1)” and “M2 (mode 2)”.

Typically, select M1.

M1 is more accurate and takes significantly longer to achieve

lock status compared with M2. If lock status cannot be

achieved (the CLOCK MODE button flashes and the display

shows “WRD UNLCK!”) using M1, select M2.

Changing the display mode

During playback, it is possible to change the display as shown

here.

< The DISPLAY button doesn’t work during programmed

playback.

Elapsed time of current trackCurrently playing track

Time remaining for current track

Total elapsed time (disc)

Total time remaining (disc)

ENGLISH

Settings (introduction)

Turn on the main unit.

Press the SETUP button to enter the setup menu.

“AudioSetup” appears on the front panel display.

In this manual, factory settings are marked with an asterisk

“*”.

< Although it is possible to enter the setup menu while

playback is continuing, not all menu functions will be

available. Expand the number of available functions by

pressing the STOP button.

Exit the setup menu by pressing SETUP once again.

Use the cursor buttons to navigate the menus.

When a option marked with “>” is displayed, use the up

or down cursor buttons to change the setting, and press

the ENTER button to confirm the entry.

Exit the setup menu by pressing SETUP once more.

< Refer to the Setup Menu Chart on the next page.

The options you can change are marked with “>”.

Use the left and up cursor buttons (or the RETURN button) to

go back a level in the setup menu.

< When a numerical value (such as speaker distance) is

changed, the value is confirmed without pressing the ENTER

button.

Individual menu functions are described on page 19 and 20.

Repeat steps and as required.

AudioSetup GeneralSet

Analog Out SP Setup

DigitalOut

CD Direct

SP Size

Distance L/R *.*m

C *.*m

SR/SL *.*m

SP Level

L/R Size

C Size

SR/SL Size

SW ON/OFF

LR ***.*dB

C ***.*dB

SR ***.*-dB

SL ***.*dB

SW ***.*dB

Test Start

Test Tone

options options

options

Settings (introduction)

ENGLISH

Settings (Audio Setup)

Analog output settings (Analog Out)

When a option marked with “>” is displayed, use the up or

down cursor buttons to change the setting, and press the

ENTER button to confirm the entry.

2ch *

Outputs audio from the FRONT L and R terminals. If the

source is multi-channel surround, this is downmixed into 2

channels. Use this setting when you have no multi-channel

analog connections.

Multi Channel

Use this when the unit is connected to an AV amplifier with

5.1 surround analog inputs. The sound is output from the six

multi-channel analog outputs.

Note that the audio volume changes when the mode is

changed between 2-channel to multi-channel.

< Speakers should be set up properly for multi-channel use. See

page 19 for details.

Digital output settings (DigitalOut)

When a option marked with “>” is displayed, use the up or

down cursor buttons to change the setting, and press the

ENTER button to confirm the entry.

ON *

Audio is output from the digital terminals.

OFF

Audio is not output from the digital terminals. If you are not

using the digital terminals, we suggest that you use this OFF

setting for better analog sound.

No digital output is possible from Super Audio CDs.

CD Direct

When a option marked with “>” is displayed, use the up or

down cursor buttons to change the setting, and press the

ENTER button to confirm the entry.

This setting matters only when playing back audio CDs.

Direct *

Speaker setting is bypassed.

Normal

The speaker setting you have made is used.

Settings (Speaker Setup 1)

Use these speaker setup menus when connecting an AV

amplifier with analog outputs, using the 5.1 multi-channel

setting (there is no need for this setup when not using multi-

channel analog connections).

When “Direct” is chosen as the CD playback option (see page

19), the settings made here are ignored.

These speaker menus allow you to select the size, distance

from the listening position, and relative levels, as well as

generating a test tone.

Speaker Size (SP Size)

Select the size (Large* or Small) independently for the L/R

(front pair of speakers), the C (center speaker) and the SR/SL

(surround pair of speakers). Turn the subwoofer (SW) ON* or

OFF (if you have no subwoofer).

Large *

Select this when the connected speakers can fully reproduce

sounds below 80 Hz.

Small

Select this when the connected speakers are rather small and

cannot reproduce sounds below 80 Hz.

When this setting is selected, bass frequencies below 80 Hz

are output from the subwoofer (if no subwoofer is

connected, from the front speakers).

OFF

Select this when no speaker is connected. The sound is

output from the front (or surround) speakers.

When the front speaker is set to “Small”, the subwoofer is

set to “ON” automatically. You cannot set the subwoofer

“OFF”.

ON (subwoofer only)

Select this when a powered subwoofer is connected.

< For the center and surround pair options, if these speakers are

not physically present, you can select OFF to prevent any

output from those channels (you cannot turn off the front L/R

pair). Any speakers turned off will downmix (if this option is

selected) to the other enabled channels.

Turning downmix on and off may affect the overall volume.

Speaker distance

Ideally, the speakers should be placed so that they are all the

same distance from the listening position. If this is not

possible, you should use this method described here to adjust

them individually. It is also possible to adjust all distances

together. The point of these settings is to provide the best

synchronization between sound and image by delaying the

sound by an appropriate amount. The subwoofer is not

included in this setting (the placement of the subwoofer is

less critical than that of other speakers).

The L/R setting changes the distance of all speakers together.

Pressing the up button adds 0.1m to each value, and pressing

the down button subtracts 0.1m from each value.

Distances are measured in meters (1 meter = just over 3 feet,

and 0.1 meter = about 4 inches).

Carry out this operation first before setting the other speaker

distances.

After setting the L/R, C and SR/SL speaker distances together,

you can now set the center and surround pair distances. The

minimum distance for these is 0m and the maximum is 9m,

with the additional restrictions described here.

The distance that you set for the center speaker cannot be

greater than the distance set for the L/R pair and must be

within 1.7m of that L/R distance.

So for example, if the distance to the L/R pair is set to 5.0m,

the center distance must be between 3.3m (5 - 1.7) and 5m.

The distance that you set for the SR/SL surround pair cannot

be greater than the distance set for the L/R pair (and must be

within 9m of that distance).

So with the L/R pair set at 5m, the SR/SL pair distance can be

set from 0m to 5m.

Speaker levels (SP Level)

Use this to set the relative levels of the speakers. You can set

the L/R pair together, and the center, and surround rear pair

independently, as well as the subwoofer. The maximum value

you can set here is +6dB and the minimum is -12dB, with

settings made in 0.5dB increments. The default setting is each

speaker channel set to 0dB.

1. Select “Test Start” and press the ENTER button.

The unit outputs pink noise from each channel in turn at the

specified level for each channel.

< Adjust the master volume of your amplifier to the normal

listening level.

2. Select a speaker using the up or down cursor buttons.

3. Press the right cursor button.

4. Adjust the levels using the up or down cursor buttons.

5. When the setting has been finished, press the SETUP

button to exit the setup menu.

Test tone length (Test tone)

Select the Test Tone menu item, and choose between 2, 5*

and 10 seconds. This represents the length of time that the

pink noise is output from each speaker when Test Start is

selected.

Settings (Speaker Setup 2)

La page charge ...

TEAC Esoteric X-01 Manuel utilisateur

Marque: TEAC

Modèle: Esoteric X-01

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: TEAC Esoteric X-01 User manual
Deutsch: TEAC Esoteric X-01 Benutzerhandbuch

TEAC Esoteric X-01 Manuel utilisateur

Ce manuel convient également à

TEAC Esoteric X-01 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents