Wagan Power Dome™ PLEX Manuel utilisateur

User’s Manual / Manual de Usuario / Guide d’Utilisation

CHARGE UNIT FOR 48 HOURS BEFORE FIRST USE.

CARGUE LA UNIDAD DURANTE 48 HORAS ANTES DEL PRIMER USO.

CHARGER L’UNITÉ PENDANT 48 HEURES AVANT LA PREMIÈRE UTILISATION.

We are constantly improving our products so speciﬁcations are subject to change

without notice. Visit our website for the latest product information.

Estamos mejorando nuestros productos constantemente, por lo tanto, las especiﬁcaciones están sujetas a cambios

sin previo aviso. Visite nuestro sitio web para obtener la información más reciente de los productos.

Nous améliorons constamment nos produits, alors les spéciﬁcations sont sujettes à changement sans

préavis. Visitez notre site Web, pour obtenir les dernières informations sur nos produits.

BC

Power Dome

®

Plex

Item No. / Artículo N

o

/ Article n° 7561

www.wagan.com

Power Dome

®

Plex by Wagan Tech

®

2

www.wagan.com

CONTENTS

Important Information �� 6

General Warnings �� 6

Storage �� 6

Proper Disposal �� 6

Product Features �� 7

Speciﬁcations �� 7

Front View �� 8

Rear View �� 9

Battery Status �� 10

Charging the Power Dome �� 10

Jumpstarter ��11

Air Compressor �� 12

Power Inverter �� 13

DC Output Socket �� 14

USB Power Port �� 14

Work Light �� 15

AM/FM Radio �� 15

3�5mm Audio Input �� 15

Troubleshooting�� 16

Manual de Usuario—Leer antes de utilizar este equipo

Wagan Tech y wagan.com son marcas registradas de la Corporación Wagan.

3

www.wagan.comwww.wagan.com

CONTENIDO

Información importante �� 18

Advertencias generales� �� 18

Almacenamiento �� 18

Manera correcta de desechar la unidad �� 18

Características del producto�� 19

Especiﬁcaciones�� 20

Vista frontal �� 21

Vista trasera �� 22

Estado de la batería �� 23

Cómo cargar el Power Dome �� 23

Puente de arranque �� 24

Compresor neumático �� 26

Inversor de corriente �� 27

Enchufe de salida de CC �� 28

Puerto de alimentación USB �� 28

Luz de trabajo �� 28

Radio AM/FM �� 28

Entrada de audio de 3,5 mm �� 29

Solución de problemas �� 30

4

Power Dome

MD

Plex de Wagan Tech

MD

www.wagan.com

TABLE DES MATIÈRES

Renseignement important �� 32

Avertissements généraux �� 32

Entreposage �� 32

Élimination appropriée �� 33

Caractéristiques du produit �� 33

Spéciﬁcations �� 34

Vue avant �� 35

Vue arrière �� 36

Recharge du Power Dome �� 37

Démarreur d'appoint �� 38

Compresseur d'air �� 40

Convertisseur continu-alternatif ��41

Prise de sortie CC �� 42

Port d'alimentation USB �� 42

Lampe de travail �� 43

Radio AM/FM �� 43

Entrée audio de 3,5 mm �� 43

Dépannage �� 44

www.wagan.com

Power Dome

®

Plex by Wagan Tech

®

6

www.wagan.com

Thank you for purchasing the Power Dome

®

Plex by Wagan Tech

®

. With normal care and proper

treatment it will provide years of reliable service.

IMPORTANT INFORMATION

• Please read and understand all warnings, cautions, and notes included in this manual before

using the Power Dome

®

Plex. Follow instructions provided by your vehicle manufacturer and

other devices intended to be used with this unit. Keep these instructions for future reference.

• Make sure the Power Dome is fully charged before ﬁrst use. We recommend 48 hours for

initial charge.

GENERAL WARNINGS

HIGH VOLTAGE: The inverter output can be lethal� Improper use may result in

property damage, personal injury, or loss of life�

• This appliance is NOT intended for use by persons with reduced physical, sensory, or

mental capabilities.

• Children or persons lacking in experience and knowledge also should NOT operate this

appliance unless he/she has been given supervision or instruction concerning the proper

usage and warnings of the appliance by a person responsible for their safety.

• For proper and safe operation of any accessory outlet, do not place anything in it except

the plug of the accessory to be used.

• Use only the chargers, cables, and clamps provided. Unauthorized parts may damage

the unit.

• This product has no consumer serviceable parts other than the external fuse. Do not

attempt to open the unit’s enclosure, doing so will void the warranty.

STORAGE

This unit may be stored in any position. Make sure the clamps and air hose are securely tucked

away in their original positions. Store in a cool, dry area. If the unit is not used for a prolonged

period of time, recharge every 3 months.

PROPER DISPOSAL

• Appliance, accessories, and packaging should be recycled in an environmentally friendly

manner. Plastic parts are coded for purposes of separation when recycling.

• Battery-powered electrical appliances contain materials which are harmful to the

environment. Do not dispose of batteries and/or electric/electronic appliances in normal

household refuse. When the battery has reached the end of its lifetime, please take the

entire unit to a battery recycling facility.

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

7

www.wagan.com

PRODUCT FEATURES

• Powerful jumpstarter with heavy-duty cables and clamps.

• Jumpstart cable polarity indicator for safety protection.

• Voltmeter for checking battery status.

• High pressure air ﬂow compressor for inﬂating tires and sports equipment with easy-read

analog pressure gauge.

• Built-in power inverter providing t wo 115 -volt AC outlets.

• DC accessory socket for powering DC appliances.

• One USB power port for charging mobile devices.

• Long-lasting LED area light.

• AM/FM radio to stay tuned during disasters and emergencies.

• Audio input jack.

• AC/DC recharging adapter & DC recharging cable (fused) included.

SPECIFICATIONS

Battery AGM Sealed lead acid, 12V, 14Ah

Peak Amps 1,000A

Jumper Cables 6 AWG, 24-inch

Air Compressor 260 PSI, analog gauge

Inverter Continuous Output Power 400W (modiﬁed sine wave)

Inverter Peak Surge 800W (for a max of 0.3 seconds)

Inverter Low Voltage Alarm 10.5V

±

0.5V

Low Voltage Shut-off 10.0V

±

0.5V

Fuse 40A

AC Outlets (2x) 115V, 60 Hz

DC Socket 12V, 11A max, 132W

USB Power Port 5V, 2.1A

Work Light 5-LED

Dial-tune Radio AM 520−1710 kHz / FM 87.5−108 MHz

Auxiliary Input Jack 3.5 mm diameter (

1

/

8

inch)

Charging Time (AC) 34 hours

Charging Time (DC—with engine running) 12 hours

Dimensions W×L×H (inches) 12.0 × 9.0× 11. 5

Weight (lb) 17. 5

AC Charging Adapter Output 12V, 500mA DC

Power Dome

®

Plex by Wagan Tech

®

8

www.wagan.com

FRONT VIEW

1. DC Socket

2. Inverter Power Indicator

3. Inverter/USB Switch

4. AC Outlets

5. Fuse

6. Voltmeter

7. Battery Status Button

8. Charging Jack

9. Charging Indicator

10. Reverse Polarity Indicator

11. Worklight Switch

12. LED Worklight

13. Jumper Cables (sides)

3

2

1

4

5

7

10

8

9

11

13

12

6

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

9

www.wagan.com

REAR VIEW

14. USB Power Port

15. Radio Tuning Dial

16. Radio Power and Volume Knob

17. Radio AM/FM Switch

18. Audio Input Jack

19. Speaker

20. Antenna

21. Jumper Safety Switch

22. Pressure Gauge

23. Air Compressor Switch

24. Air Compressor Hose

18

14

20

21

22

23

24

15

16

17

19

Power Dome

®

Plex by Wagan Tech

®

10

www.wagan.com

BATTERY STATUS

The voltmeter provides the current state of charge on the internal battery. It is the user’s

responsibility to periodically monitor the battery’s status and recharge every 3 months in addition

to recharging after each use.

1. Disconnect any input or output power cords and turn off all switches.

2. Press and hold the Battery Status button.

3. Read the voltmeter to determine battery status.

•

<

12V: Battery is discharged, charge immediately

• ~ 12V: Battery should be charged before jump starting a vehicle

•

>

12.5V: Battery is adequate for jump starting

CHARGING THE POWER DOME

ELECTRICAL SHOCK! Exposure to water may cause electrical shock� Exposure to

water and excessive moisture will also damage the unit and void the warranty�

Charge your Power Dome in an upright position for a full 48 hours before initial use� The

Power Dome can be charged continuously via AC adapter without damaging the internal battery.

In order to prolong the life of the Power Dome (as with all lead-acid batteries), be sure to fully

recharge the unit every 3 months even if the Power Dome has not been used.

AC Charging

Only use the AC charging adapter supplied with this unit� Make sure the supplied AC/DC

charging adapter is powered by the correct voltage (110V AC or 220V AC depending on your

country/region).

1. Make sure all Power Dome switches are off.

2. Open the dust cover on the charging jack.

3. Plug the DC end of the AC/DC charging adapter into the Power Dome’s charging jack.

4. Connect the AC end of the AC/DC charging adapter to the wall outlet.

5. The charging indicator will light up during the charging process.

6. When charge is complete, disconnect the adapter from the AC outlet ﬁrst, then from the

charging jack.

7. Replace the dust cover on the charging jack.

DC Charging in Your Vehicle or Boat

Only use the DC charging adapter supplied with this unit� Your vehicle engine must be

running while charging the Power Dome. Do NOT exceed 12 hours of continuous charging time.

1. Make sure all Power Dome switches are off.

2. Open the dust cover on the charging jack.

3. Plug the small end of the DC power cord into the Power Dome’s charging jack.

4. Plug the large end of the DC power cord into an accessory (cigarette lighter) socket.

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

11

www.wagan.com

5. The charging indicator will light up during the charging process. Do NOT charge for more

than 12 hours at one time.

6. When charge is complete, disconnect the power cord from the accessory socket ﬁrst, then

from the unit’s charging jack.

7. Replace the dust cover on the charging jack.

JUMPSTARTER

Warnings

• Lead-acid batteries can release explosive gases. Failure to follow instructions

may cause property damage, explosion hazard, and/or personal injury.

• Do not smoke while jumpstarting.

• Jumpstart a vehicle or boat in a well ventilated area.

• Do not attempt to jumpstart a frozen battery.

• This product is not intended for use in the rain or temperatures above 130°F.

• Do not let the jumper cables or other attached appliances get wet.

• Do not wear vinyl clothing when jumpstarting—friction can cause static

electricity sparks.

• Remove all metal jewelry to avoid short circuits.

• Always use safety glasses when jumpstarting battery. Keep battery terminals clean and be

careful to keep corrosion from coming in contact with eyes—acid can cause blindness and/

or severe burns.

• Never allow red and black clamps to touch or connect to the same piece of metal—this can

cause short-circuits, power arcing, and/or explosion.

• Make sure someone is available to give assistance if needed.

• Keep out of reach of children.

• This unit is for use with 12 volt systems only.

Operation

CAUTION: If the engine fails to start after three attempts, discontinue jumpstart procedure�

Excessive engine cranking can damage the vehicle’s starter motor� Look for other problems

that may need to be corrected or call for professional service�

1. Review the Jumpstarter warnings.

2. Put the vehicle’s gear in “park” position and make sure the brake is set.

3. Turn off the vehicle ignition and accessories (e.g. radios, lights, air conditioners), and

disconnect all devices such as GPS and mobile phones or tablets.

4. Turn off all Power Dome switches and disconnect all accessories.

5. Determine the polarity of the vehicle’s battery terminals. The positive (POS, P, +) battery

terminal is usually larger in diameter than the negative (NEG, N, −) terminal. If you are

unsure, you should refer to the vehicle owner’s manual.

Power Dome

®

Plex by Wagan Tech

®

12

www.wagan.com

6. Determine the ground system of your vehicle.

• If vehicle to be started has a negative ground system (this is most common):

a. Connect the red (+) cable clamp ﬁrst to the vehicle’s positive (red) battery terminal.

b. Next, connect the black (−) clamp to the vehicle chassis or a solid, non-moving,

metal vehicle component or body part. DO NOT clamp directly to negative battery

terminal or a moving part.

• If vehicle to be started has the positive battery terminal connected to chassis (this is rare

and usually found in older car models from the 1950s or earlier):

a. Connect the black (−) clamp ﬁrst to vehicle battery’s negative (black) terminal.

b. Connect red (+) clamp to vehicle chassis or a solid, non-moving, metal vehicle

component or body part. DO NOT clamp directly to positive battery terminal or a

moving part.

7. Observe the color of the Reverse Polarity Protection Indicator.

• If the light is RED, DO NOT TURN ON THE JUMPER SAFETY SWITCH!

a. Cable clamps need to be reversed.

b. Disconnect the black clamp ﬁrst then the red clamp.

c. Reconnect and observe the indicator again.

• If the light is GREEN, turn on the Jumper Safety Switch.

a. Inside the vehicle, turn on the ignition switch and attempt to start the engine.

b. Crank a maximum of 3 seconds. If the engine does not start, wait 3 minutes before

the next attempt.

c. After the engine starts, turn off the Jumper Safety Switch.

d. Disconnect the clamps in the reverse order of connection prior to jumpstarting.

8. Be sure that the cables and clamps are securely stored.

9. Recharge the Power Dome as soon as convenient.

AIR COMPRESSOR

This Power Dome is equipped with an air compressor that can provide up to 260 PSI (pounds per

square inch) of pressure for a variety of uses such as vehicle tires and sports equipment.

CAUTION: Be careful not to over inﬂate, monitor the compressor gauge while inﬂating. Never

connect or disconnect the nozzle with the compressor operating. To avoid overheating, do

not operate the air compressor for more than 10 minutes at a time. After 10 minutes, allow the

compressor to cool for 15 minutes before using again.

Operation

In the event that the vehicle tire is completely ﬂat, raise the vehicle using a recommended jack

before inﬂating the tire.

1. Before any tire inﬂation, look for manufacturer’s recommended inﬂation pressure.

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

13

www.wagan.com

2. Open the compartment door at the rear of the Power Dome and extend the air hose.

3. Position the Power Dome so that you can see the pressure gauge.

4. Make sure the chuck lever is positioned up (away from the chuck opening).

5. Determine if you will need an air hose adapter for your object.

• To inﬂate a vehicle tire:

a. Remove the valve cap from the valve stem of the tire.

b. Attach the chuck of the air hose to the tire’s valve stem.

c. Push the chuck lever down to secure the chuck to the valve stem.

• To inﬂate a sports equipment, air mattress, rafts, or other plastic inﬂatables:

a. Insert the proper valve stem adapter into stem connector as far as possible.

b. Push the chuck lever down to secure the adapter.

c. Remove the valve cap from your inﬂatable object if there is one.

d. Insert the other end of the valve stem adapter into inﬂatable’s air valve opening

as far as possible.

6. Set the Air Compressor Switch on to the “I” position to start inﬂation.

7. Monitor the pressure gauge while inﬂating the tire.

8. When recommended tire pressure has been reached, turn off the air compressor.

9. Disconnect the hose and replace valve cap.

10. Return the hose back to its compartment for storage.

11. Recharge the Power Dome as soon as it is convenient.

POWER INVERTER

The Power Dome

®

Plex can run most AC appliances or a combination of appliances up to 400

watts. Operating time is dependant on the AC load (required wattage) and the current charge/

condition of the Power Dome’s internal battery. Reduced AC loads and/or having a full charge on

the internal battery will result in longer operating time. Ordinary overloads will cause the inverter

to automatically shut down. Reduce the load and restart the inverter.

There is a user-replaceable automotive-type fuse protecting the inverter from an unlikely excessive

power draw or short circuit. REPLACE ONLY WITH THE SAME TYPE AND RATING FUSE. To

replace the fuse, simply pull it out with a pair of needle nose pliers and insert the new fuse.

Caution

Some rechargeable devices are equipped with a separate AC charger. These devices are

likely to operate properly with the inverter in this unit. Rechargeable devices that have built-in

chargers (see your device’s user manual) may not operate properly with this unit because the

inverter is modiﬁed sine wave.

Some motorized devices may operate at excessively elevated temperature when used with this

inverter. During ﬁrst use with this inverter, check for excessive motor temperature. Abnormally

elevated temperature of the device is an indication that they should not be used together.

Power Dome

®

Plex by Wagan Tech

®

14

www.wagan.com

Operation

1. Check the required current draw of the appliance/device to be powered and make sure it

does not exceed the Power Dome’s maximum wattage.

2. Prior to plugging in your device, turn your power tool or appliance off. Mobile devices are

ﬁne to keep on, but operating them during the charging process will prolong charging time.

3. Open the AC outlet dust cover.

4. Connect the electrical plug of your device/appliance to either of the two AC outlets.

5. Set the Inverter/USB Switch to the “||” position.

6. Observe the Inverter Power Indicator. If the LED remains green, proceed to plugging in and

turning on the second device/appliance.

• If the power indicator remains green, then both devices/appliances are operating

properly.

• If the power indicator is no longer lit, reduce the AC load. If the inverter still does not

operate after load is reduced, refer to the troubleshooting table at the end of this User’s

Manual.

7. After use, remove the device/appliance plug(s), close the dust cover(s), and turn the Inverter/

USB Switch off.

8. Recharge the Power Dome as soon as it is convenient.

DC OUTPUT SOCKET

The DC accessory socket can power a DC load up to 11 Amps. Overloading the socket will result

in tripping the self-resetting circuit breaker. Removing the overload automatically restores power

to the DC socket. For proper and safe operation of the 12 Volt DC power accessory socket, do

not place anything in them except the 12V DC plug of the accessory to be used.

1. Check the required current draw of the appliance/device to be powered and make sure it

does not exceed the Power Dome’s maximum wattage.

2. Remove the dust cover from the DC socket.

3. Insert the 12V DC plug of your device/appliance into the Power Dome’s DC socket.

4. Operate your device/appliance as usual.

5. After use, remove the device/appliance’s plug and close the dust cover.

6. Recharge the Power Dome as soon as convenient.

USB POWER PORT

1. Connect a user-supplied USB cable to the USB power port on the Power Dome.

2. Set the Inverter/USB Switch to “I” position. (You may also choose to operate the USB and

AC outputs at the same time by setting the switch to the “II” position.)

3. Check for the indicator to be lit.

4. Operate your mobile device as usual.

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

15

www.wagan.com

5. After use, disconnect the USB cable and turn the Inverter/USB Switch off.

6. Recharge the Power Dome as soon as convenient.

WORK LIGHT

The Work Light is a cluster of bright LEDs located at the side of the Power Dome. The location of the

Work Light allows the light to be used while the Power Dome is being carried.

1. Set the Light Switch to the “|” position.

2. The light will illuminate.

3. Turn off the light when it is not in use.

AM/FM RADIO

The Power Dome’s radio can receive frequencies in the standard AM and FM broadcast bands (AM

520–1710 kHz, FM 88–108 MHz). An extendable antenna provides adequate signal to receive all

local radio stations. When not in use, the antenna should be stored in the retracted position. This will

prevent damage to the antenna while Power Dome is being transported.

NOTE: All AM band radios are subject to receiving noise interference from electronic devices, static

lightning strikes, and some motorized equipment. If you are operating the Power Dome’s inverter and

noise is being received on the AM band, turn off the inverter or change the radio to receive an FM

frequency.

Turning On the Radio

1. Carefully raise and extend the antenna.

2. Turn the radio Power/Volume knob clockwise to turn the radio on. The more you turn the knob to

the right, the higher the volume.

3. Turn the “TUNING” knob in either direction to adjust the station.

4. When ﬁnished, turn the radio Power/Volume knob counter-clockwise to turn the radio off.

5. Carefully retract the antenna and return it to the lowered position.

3�5MM AUDIO INPUT

1. Turn the radio on.

2. Insert a user-supplied 3.5mm audio cable into the auxiliary input jack.

3. Insert the opposite end of the cable into a compatible audio device.

4. Turn on the audio device and set it to output sound. The sound should be audible from the Power

Dome speakers.

Note: The Power Dome’s USB Power Port can conveniently charge your audio or mobile device while

music is playing.

Power Dome

®

Plex by Wagan Tech

®

16

www.wagan.com

TROUBLESHOOTING

Problem Cause Solution

Air compressor shut-off. High temperature

protection.

Allow the Power Dome cool for about 10 minutes.

Lack of power output. Power Dome battery

voltage is below 10 volts.

Recharge the Power Dome immediately.

Excessive current drawn

by appliance being

operated.

Reduce load to maximum wattage.

1. Turn off the device and inverter.

2. Disconnect device.

3. Turn the inverter on and let it run for a

minimum of 2 minutes.

4. Turn inverter off.

5. Quickly plug device into inverter.

6. Turn on both the inverter and the device.

Inverter fuse blown. Check and replace if necessary. Be sure

replacement fuse is the same type and rating.

Loud buzzing sound. Battery charge level is

too low.

1. Disconnect all appliances.

2. Turn inverter off.

3. Charge Power Dome fully. (See charging

section for more details.)

Inverter Power Indicator

is not lit.

Excessive voltage drop. Check internal battery status and recharge if

voltage drops below 10 volts.

Inverter is overloaded. Reduce load to maximum wattage.

Inverter automatically

shuts down.

AC overload. Unplug and power off to restart then reduce AC

load to maximum wattage.

Television/power

tool will not start.

Required wattage

exceeds Power Dome

peak surge for start-up.

Toggle the Inverter Switch on and off in quick

succession for 5 times. If the device does not

start, the device is not compatible with this type

of inverter.

Television Interference. Picture breaking up

(static).

Place the Power Dome as far as possible from

the TV, antenna, and coaxial cable.

TV station may be out of range.

Static/noise interference

in audio system.

Sound system has weak

alternating current

shielding.

Do not use the Power Dome’s inverter with low-

quality audio AC ﬁltering system.

Replace audio system with high quality noise

ﬁltering.

www.wagan.com

WAGAN Corp. Limited Warranty

The WAGAN Corporation warranty is limited to products sold only in the

United States.

Warranty Duration:

Product is warranted to the original purchaser for a period of one (1) year from the

original purchase date, to be free of defects in material and workmanship. WAGAN

Corporation disclaims any liability for consequential damages. In no event will WAGAN

Corporation be responsible for any amount of damages beyond the amount paid for

the product at retail.

Warranty Performance:

During the warranty period, a product with a defect will be replaced with a comparable

model when the product is returned to WAGAN Corporation with an original store

receipt. WAGAN Corporation will, at its discretion, replace or repair the defective part.

The replacement product will be warranted for the balance of the original warranty

period. This warranty does not extend to any units which have been used in violation

of written instructions furnished.

Warranty Disclaimers:

This warranty is in lieu of all warranties expressed or implied and no representative

or person is authorized to assume any other liability in connection with the sale of our

products. There shall be no claims for defects or failure of performance or product

failure under any theory of tort, contract or commercial law including,but not limited to

negligence, gross negligence, strict liability, breach of warranty, and breach of contract.

Returns:

WAGAN Corporation is not responsible for any item(s) returned without an ofﬁcial

Return Authorization number (RA#). Please contact our customer service team by phone

or email to obtain an RA#. You can also visit our website and chat with our team

during our normal business hours. For more details and instructions on how to process

a warranty claim, please read the “Returns” section under the “Contact” page on our

website. WAGAN Corporation is not responsible for any shipping charges incurred in

returning the item(s) back to the company for repair or replacement.

Register your product online at http://tinyurl.com/wagan-registration to be added to our

email list. You will receive previews on our upcoming products, promotions, and events.

Power Dome

®

Plex de Wagan Tech

®

18

www.wagan.com

Gracias por su compra del Power Dome

®

Plex fabricado por Wagan Tech

®

. Con el cuidado

normal y el tratamiento adecuado, le ofrecerá años de servicio conﬁable.

INFORMACIÓN IMPORTANTE

• Lea y entienda todas las advertencias, precauciones y notas incluidas en este manual antes

de usar el Power Dome

®

Plex. Siga las instrucciones que le proporcionó el fabricante de

su vehículo y otros dispositivos concebidos para usar con esta unidad. Conserve estas

instrucciones para referencia futura.

• Asegúrese de que el Power Dome esté completamente cargado antes de usarlo por primera

vez. Recomendamos 48 horas para la carga inicial.

ADVERTENCIAS GENERALES�

ALTO VOLTAJE: La salida del inversor puede ser letal� El uso indebido puede

ocasionar daños a la propiedad, lesiones personales, o pérdida de la vida�

• Ese aparato NO está concebido para que lo usen personas con capacidad física, sensorial

o mental reducida.

• Los niños o personas carentes de experiencia y conocimientos TAMPOCO deben operar

este aparato, a menos que una persona responsable de su seguridad los supervise o se les

haya dado instrucciones y advertencias respecto del uso adecuado del aparato.

• Para una operación adecuada y segura de una toma de corriente auxiliar, no coloque nada

en ella, excepto el enchufe del accesorio que se va a usar.

• Use únicamente los cargadores, cables y abrazaderas que se proveen. Las partes no

autorizadas pueden dañar la unidad.

• Este producto no tiene partes que el consumidor pueda reparar adicionalmente al fusible

externo. No trate de abrir la cápsula de la unidad, ya que ello podría invalidar la garantía.

ALMACENAMIENTO

Esta unidad puede guardarse en cualquier posición. Asegúrese de que las abrazaderas y la

manguera de aire estén escondidas en sus posiciones originales. Guarde en un lugar fresco

y seco. Si la unidad no se usa en un período de tiempo prolongado, recárguela cada 3

meses.

MANERA CORRECTA DE DESECHAR LA UNIDAD

• El aparato, los accesorios y el empaque deben reciclarse de manera que no perjudique al

medio ambiente. Las partes de plástico están codiﬁcadas para separarlas para el reciclaje.

• Los aparatos eléctricos que funcionan con baterías contienen materiales que son dañinos

para el medio ambiente. No deseche las baterías y/o los aparatos eléctricos o electrónicos

junto con desechos domésticos normales. Cuando la batería haya llegado al ﬁn de su vida

útil, lleve la unidad completa a un lugar donde reciclen baterías.

Manual de Usuario—Leer antes de utilizar este equipo

Wagan Tech y wagan.com son marcas registradas de la Corporación Wagan.

19

www.wagan.com

CARACTERÍSTICAS DEL PRODUCTO

• Potente puente de arranque con cables y abrazaderas de alta resistencia.

• Indicador de polaridad del cable del puente de arranque para protección de la seguridad.

• Voltímetro para veriﬁcar el estado de la batería.

• Compresor del ﬂujo de aire de alta presión para inﬂar llantas y equipos deportivos con un

manómetro análogo de fácil lectura.

• Inversor de potencia integrado que provee dos salidas de 115 voltios de CA.

• Enchufes accesorios de CC para los aparatos de CC.

• Un puerto de alimentación USB para cargar dispositivos móviles.

• Luz de área LED, de larga duración.

• Radio AM/FM para mantenerse sintonizado en casos de desastres y emergencias.

• Enchufe de entrada de audio.

• Adaptador de recarga CA/CC y cable de recarga de CC (con fusible) incluido.

Power Dome

®

Plex de Wagan Tech

®

20

www.wagan.com

ESPECIFICACIONES

Batería AGM sellada de plomo-ácido, 12 V, 14Ah

Amperios pico 1,000A

Cable para puente de arranque 6 AWG, 61 centímetros

Compresor neumático Manómetro análogo de 260 PSI

Potencia de salida continua del inversor 400 W (onda sinusoidal modiﬁcada)

Voltaje máximo del inversor 800 W (para un máximo de 0.3 segundos

Alarma de bajo voltaje del inversor 10.5 V

±

0.5 V

Apagado por bajo voltaje 10.0 V

±

0.5 V

Fusible: 40 A

Toma(s) de corriente CA (2x) 115 V, 60 Hz

Enchufe(s) de CC 12 V, 11 A máx, 132 W

Puerto de alimentación USB: 5 V, 2.1A

Luz de trabajo 5-LED

con dial -sintonizador digital AM 520−1710 kHz / FM 87.5−108 MHz

Enchufe de entrada de audio Diámetro de 3.5 mm (

1

/

8

de pulgada)

Tiempo de carga (CA) 34 horas

Tiempo de carga (CC—con el motor

funcionando)

12 horas

Medidas AxLxA (centímetros) 30.5 × 22.9 × 29.2

Peso (kilogramo) 7.9

Salida de corriente de adaptador de carga

de CA

12 V,500 mA CC

La page charge ...

Wagan Power Dome™ PLEX Manuel utilisateur

Ce manuel convient également à

Wagan Power Dome™ PLEX Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents