GE Water Dispenser GXRM10GBL Manuel utilisateur

Marque: GE

Modèle: Water Dispenser GXRM10GBL

Catégorie: Articles sanitaires

Taper: Manuel utilisateur

Ce manuel convient également à

GXRM10GBL

ge.com
Reverse Osmosis
273-40R010-1900D    215C1044P034    49-50199-1 12-07 JR
Filtration System
GXRM10GBL
Owner’s Manual
and Installation
Safety Instructions 
Safety Instructions . . . . . . . . . . . . . . .2
Specification Guidelines . . . . . . . . . .3
Installation Instructions
Before Beginning Installation  . . . . .4
Drain Connections  . . . . . . . . . . . . . .9
Faucet Drain Tubing and
Water Supply Tubing  . . . . . . . . . . . .9
Faucet Installation  . . . . . . . . . . . . . .8
Feed Water Supply  . . . . . . . . . . . .6, 7
System Assembly  . . . . . . . . . . . . . . .10
Things to Check 
Before Installation  . . . . . . . . . . . . . .5
Tools and Materials Required  . . . . .4
Care and Cleaning
Prefilter, Postfilter and 
RO Cartridge Replacement  . . .11, 12
Sanitization  . . . . . . . . . . . . . . . . . . .11
Water Test Kit  . . . . . . . . . . . . . . . . .13
Operating Instructions
About the RO System  . . . . . . . .14, 15
Troubleshooting Tips  . . . . . . . . . .16
Consumer Support
Consumer Support  . . . . .Back Cover
Parts List/Catalog . . . . . . . . . . .17, 18
Warranty  . . . . . . . . . . . . . . . . . . . . .20
Manuel d’utilisation 
et d’installation
Manual del propietario
y instalación
La section française commence à la page 21
Osmose Inversée
Système de Filtration
La sección en español empieza en la página 41
Ósmosis Inversa
Sistema de Filtración
GXRM10GBL is Tested and
Certified to NSF/ANSI Standard
58. See Performance Data Sheet
for specific claims.
Write the model and serial 
numbers here:
Model # __________________
Serial # __________________
You can find them on the bracket.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

■ Check with your state and local public works

department for plumbing and sanitation codes.

You must follow these guidelines as you install the

Reverse Osmosis system. Using a qualified installer

is recommended.

■ If house water pressure is over the maximum

(125 pounds per square inch), install a pressure

reducing valve in the water supply line to the

Reverse Osmosis system.

■

Be sure the water supply conforms with the

Specification Guidelines. If the water supply

conditions are unknown, contact your municipal

water company or your local health department

for a list of contaminants in your area and a list of

laboratories certified by your state to analyze

drinking water.

WARNING: Before using the Reverse Osmosis

system for the first time, the system must be

purged. The Reverse Osmosis cartridge contains

a food grade preservative that must be purged

from the system. The preservative will give product

water an unpleasant taste and odor.

■ This product reduces fluoride in drinking water.

Please consult your dentist if you have questions.

WARNING: Do not use with water that is

microbiologically unsafe or of unknown quality

without adequate disinfection before the system.

Systems certified for cyst reduction may be used on

disinfected water that may contain filterable cysts.

This system has been tested for the treatment of

water containing pentavalent arsenic (also known as

As(V), As(+5) or arsenate) at concentrations of

0.050 mg/L or less. This system reduces

pentavalent arsenic, but may not remove other

forms of arsenic. This system is to be used on water

supplies containing a detectable free chlorine

residual or on water supplies that have been

demonstrated to contain only pentavalent arsenic.

Treatment with chloramine (combined chlorine)

is not sufficient to ensure complete conversion of

trivalent arsenic to pentavalent arsenic. Please see

the Arsenic Facts section of the Performance Data

Sheet for further information.

This Reverse Osmosis system contains a replaceable

treatment membrane cartridge critical for effective

reduction of Total Dissolved Solids. The water

should be tested periodically to verify that the system

is performing satisfactorily. See the About the Water

Test Kit section. This system is acceptable for

treatment of influent concentrations of no more

than 27 mg/L nitrate and 3 mg/L nitrite in

combination measured as N and is certified for

nitrate/nitrite reduction only for water supplies

with a pressure of 280kPa (40 psig) or greater.

SAVE THESE INSTRUCTIONS

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

■ Install or store where it will not be exposed to

temperatures below freezing or exposed to any

type of weather. Water freezing in the system will

damage it. Do not attempt to treat water over 100°F.

■ Do not install on HOT WATER. The temperature

of the water supply to the Reverse Osmosis system

must be between the minimum of 40°F and the

maximum of 100°F. See the Specification Guidelines.

■ Extended non-use of the Reverse Osmosis system.

If the system has not been used for one week or

more, open the RO water faucet and allow the

system to drain. Close the RO water faucet and

allow the system to regenerate the water supply.

■ Recommended installation is under the sink.

However, the unit can be installed in a remote

location, up to 20 feet away from the sink.

Additional installation materials may be required.

If Reverse Osmosis system is connected to a

refrigerator icemaker, a special icemaker

connection kit is required (RVKIT). Do not use

copper tubing for the connection between the

Reverse Osmosis system and the refrigerator.

WARNING: Discard all unused parts and

packaging material after installation. Small parts

remaining after the installation could be a choke

hazard.

■

Sanitize upon installation of the Reverse Osmosis

system and after servicing inner parts, including

replacement of prefilter, postfilter and Reverse

Osmosis cartridge. It is important to have clean

hands while handling inner parts of the system.

See the Sanitizing the Reverse Osmosis System section.

■

This Reverse Osmosis system contains a replaceable

component critical to the efficiency of the system.

Replacement of the Reverse Osmosis component

should be with one of identical specifications, as

defined by the manufacturer, to assure the same

efficiency and contaminant reduction performance.

See Automatic Shutoff Valve section on page 14.

BE SURE TO FOLLOW ALL APPLICABLE STATE

AND LOCAL CODES.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of

property damage or personal injury.

SAFETY PRECAUTIONS

PROPER INSTALLATION AND MAINTENANCE

This Reverse Osmosis system must be properly installed and located in accordance with the

Installation

Instructions before it is used.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation Instructions

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Specification guidelines.

ge.com

The system makes a good supply of drinking water each day.

How much it will make depends primarily on these things…

Product – height 15″ width 14″ depth 5.5″

Incoming Water pH

WATER SOFTENER RECOMMENDED

INCOMING WATER HARDNESS (GPG)

2010

7.5

6.5

Water Softener

not required

Maximum iron, manganese, hydrogen sulfide (ppm) . . . . . . . . . . . . . . . . . . . . . .<0.1

Chlorine in water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 ppm maximum allowable

Feed water pH limits (pH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–10

Product (quality) water, 24 hours—gallons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.0

Percent rejection of TDS (new membrane) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92.4%

Cyst reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99.99%

Storage tank capacity—gallons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Efficiency rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.7%

Recovery rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16.6%

Automatic shutoff control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .yes

Prefilter and postfilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(FX12P) Carbon Block

Reverse Osmosis membrane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(FX12M) Thin Film Polyamide

Dimensions (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .height 15” width 14” depth 5.5”

Feed water pressure limits—pounds per square inch (psi) . . . . . . . . . . . . . . . . . . . . . .40–125

Feed water temperature limits—minimum/maximum degrees F . . . . . . . . . . . . . . . . .40–100

Maximum Total Dissolved Solids (TDS)—parts per million (ppm) . . . . . . . . . . . . . . . .2000

Maximum water hardness @ 6.9 pH recommended to optimize membrane

life—grains per gallon (gpg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

For water with hardness greater than 10 grains (at 6.9 pH) the use of a

softener is recommended. Failure to install a water softener will reduce

the life of the Reverse Osmosis membrane. See chart for additional

information on the possible need for a water softener.

a. Tested according to NSF/ANSI Standard 58. Source water test parameters are 50 psig, 77°F,

pH of 7.5 ± 0.5, and 750 ± 40 ppm total dissolved solids.

b. Removed by the Reverse Osmosis prefilter. REGULAR MAINTENANCE IS REQUIRED. Chlorine will

destroy the Reverse Osmosis membrane.

c. If house water pressure is over 125 psi, install a pressure reducing valve in the water supply line.

If house water pressure is under 40 psi, install a Reverse Osmosis booster pump (contact your

local plumbing supply company).

d. Theoretical tank capacity. When tested according to NSF/ANSI Standard 58 at 50 psig inlet

pressure, tank capacity is 2.3 gallons.

e. Efficiency rating means the percentage of the influent water to the system that is available

to the user as Reverse Osmosis treated water under operating conditions that approximate

typical daily usage.

f. Recovery rating means the percentage of influent water to the membrane portion of the system

that is available to the user as Reverse Osmosis treated water when the system is operated without

a storage tank or when the storage tank is bypassed.

Installation

Reverse Osmosis Filtration System

Instructions

Model GXRM10GBL

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT

— Save these

instructions for local inspector’s use.

•

IMPORTANT

— Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation

is not covered under the Warranty.

• A shutoff valve must be available or added

near the installation point.

TOOLS AND MATERIALS

REQUIRED FOR INSTALLATION

• Drill with 1-1/4″ Drill Bit (type as required)

if mounting is needed for faucet

• Adjustable Open-End Wrenches

• Phillips and Flat Blade Screwdrivers

• Utility Knife

CONTENTS INCLUDED

WITH PRODUCT

• Reverse Osmosis Assembly and Tubing

• Product Literature (Owner’s Manual and

Installation) and Performance Data Sheet

• Water Supply Inlet Parts Bag

• Drain Line Adapter

• Storage Tank

• Faucet

• Pipe Thread Tape

Installation Instructions

Things to Check Before Beginning Installation

FEED WATER

The water supply to the undercounter

Reverse Osmosis system must have the

qualities listed in the specifications (see the

Specifications Guidelines section). Municipal

water supplies most often will have these

qualities. Well water may need conditioning—

have the water tested by a water analysis

laboratory and get their recommendations

for treatment.

CAUTION: For water with a hardness

greater than 10 grains (at 6.9 pH), the use of

a softener is recommended. Failure to install

a softener will reduce the life of the Reverse

Osmosis membrane. See the Specifications

Guidelines section for additional information

on the possible need for a softener.

DRAIN POINT

A suitable drain point and air gap (check your

local codes) are needed for reject water from

the Reverse Osmosis membrane cartridge.

BASEMENT INSTALLATION

If installing in a basement, leave enough

tubing in place during installation to be able

to move unit to floor for ease at servicing and

making filter/membrane changes. Additional

tubing and fittings required.

RO FAUCET

The RO product water faucet installs on the

sink or on the countertop next to the sink.

Often, it is installed in an existing sink spray

attachment hole or a hole may be drilled.

Space is required underneath for tubing to

and from the faucet, and for securing the

faucet in place. All faucet connections and

installation procedures are done on or above

the sink or countertop. Refer to illustration

above.

Storage tank

Sink p-trap

HOT COLD

Drain adapter

3/8″ black drain tubing

RO product water faucet mounted

through sink or countertop

Feed water

adapter

Yellow

(inlet)

Orange

1/4″ black

Blue

(to faucet)

Installation Instructions

FEED WATER SUPPLY

Check and comply with local plumbing codes as you plan, then install a cold feed water supply fitting.

A. PREFERRED INSTALLATION

1. Close the cold water supply valve under

the sink.

2. Unscrew the flexible tubing from the

supply valve that connects to the COLD

water riser.

3. Install the feed water adapter* that is the

diameter to match either the 1/2″ or 3/8″

plumbing in your location. DO NOT

OVERTIGHTEN.

*Notice the direction of the feed water

adapter and coupling. It is installed

differently in order to match either the

1/2″ or 3/8″ plumbing in your location.

B. OPTIONAL HOME INSTALLATION

Where codes permit (Requires additional parts)

*For 1/2″ OD or larger metal tubing only.

NOTE: Codes in the state of Massachusetts

require installation by a licensed plumber and

do not permit the use of the saddle valve. For

installation, use plumbing code 248-CMR of the

Commonwealth of Massachusetts.

Saddle valve is available through GE Parts

and Services at 1.800.626.2002, part number

WS15X10023. Self piercing saddle valves are

not recommended.

1. Turn off the cold water supply and attach

saddle valve as shown in illustration

below.

DANGER: Many homes are

electrically grounded through the plumbing.

To protect yourself from serious injury or

fatal shock, use a battery-powered hand drill

only to make the hole. DO NOT USE AN

ELECTRIC DRILL.

2. Close the water supply valve by turning

the handle clockwise.

3. Open the main water supply valve and

several house faucets to purge air from

the system. Close faucets when water

runs smoothly.

Snug valve into bracket

(DO NOT OVERTIGHTEN)

Some threads

should be visible

Rubber gasket

Optional water supply connection (using saddle valve)*

Pre-drill

1/4″ hole

Seal—make sure

the seal is in place

Clamp X

Nut (2)—not

required if holes

in clamp are

threaded

Valve

Handle

Tubing adapter

Washer

Compression

nut



Clamp Z

Use to connect the tubing

*For 1/2 ″ OD or larger metal tubing only.

For 3/8″ Plumbing For 1/2″ Plumbing

Faucet

tubing line

Coupling

Adapter

Inlet valve

Cold water

supply valve

Faucet

tubing line

Cold water

supply valve

Coupling

Adapter

Gasket

Ferrule

Inlet valve

Nut

Gasket

Installation Instructions

C. INSTALLATION IN A

REMOTE LOCATION

(requires additional part)

1. Turn off the cold water supply.

2. Complying with plumbing codes, install a

fitting on the cold water pipe to adapt 1/4″

OD tubing. A typical connection is shown

in illustration below. Make sure a water

supply valve is used.

3. If the RO unit is to be installed more than

6 feet from the valve, replace the yellow

tubing with a longer length of GE 1/4″

tubing. A 33 foot length of 1/4″ tubing is

available through GE Parts and Services

at 1.800.626.2002, part number

WS07X10018. DO NOT SUBSTITUTE

TUBING OF UNKNOWN QUALITY.

4. If the RO unit is to be installed more than 6

feet from the faucet, replace the blue tubing

with a longer length of GE 3/8″ tubing. A 33

foot length is available through GE Parts

and Services at 1.800.626.2002, part number

WS07X10019. See Faucet Installation on

page 8 for more details. DO NOT

SUBSTITUTE TUBING OF UNKNOWN

QUALITY.

If you are using copper tubing, DO NOT

connect it directly onto the RO unit. Purchase a

connector and use a short length of the yellow

tubing provided to make final connection to RO.

Do not use copper tubing to attach to icemaker

or faucet.

Insert (not included)

Cold

water

pipe

1/4″ (yellow) tubing

to inlet

Ferrule

Water supply valve

To RO

Installation Instructions

FAUCET INSTALLATION

Be sure there is room underneath the sink to

make the needed connections. Select one of

the following locations to install the faucet:

• In an existing sink spray attachment or soap

dispenser hole.

• In a hole to be drilled in the sink top.

• In a hole to be drilled in the countertop,

next to the sink.

NOTE: Be sure the faucet base will fit flat

against the surface at the selected location

so the gasket will seal.

1. If drilling is needed, make a 1-1/4″ dia.

hole. Be sure to use the proper procedure

for drilling porcelain or stainless steel.

2. Insert the faucet spout into the body.

Tighten cap until snug.

3. Feed the blue, 1/4″ black and 3/8″ black

tubes up through the hole in the

countertop or sink.

4. Feed the two black tubes up through the

gasket, faucet base and O-ring.

NOTE: For ease of service and maintenance,

keep tubing lengths long enough so removal

of the Reverse Osmosis system from under

the sink is possible.

5. Push the 1/4″ black and 3/8″ black tubing

onto their respective barb fittings on the

body.

6. Seat the base and body together. Make

sure the O-ring and gasket are in place

when the base meets the body. The faucet

handle will be at the 3 o’clock position

with respect to the base.

7. Slide the lock washer onto the threaded

stem of the body, then thread the brass

nut onto the stem. Screw about halfway up.

8. Screw the tubing adapter to the threaded

stem of the body.

9. Push the blue tubing into the adapter. It

should go in about 1/2″. Pull on it to make

sure it is installed securely.

10. Feed the tubing and stem back down

through the 1-1/4″ hole.

11. Under the counter, insert the mounting

disk above the lock washer and tighten

the brass nut until snug.

Mounting

disk

Base

Nut

Handle

Spout

Gasket

Tubing adapter

Lock washer

O-ring

Cap

ASSEMBLED

3/8″ barb

fitting

Black 3/8″

tubing,

27″ long

Black 1/4″

tubing

1/4″ barb

fitting

Tubing adapter

Blue 3/8″ tubing

Nut

Lock washer

Body

From RO

From ROTo drain

Installation Instructions

FILTRATION DRAIN CONNECTION INSTALLATION

Check and comply with all state and local plumbing codes as you plan.

CAUTION: The options detailed in this section are the ONLY approved installation

configurations. Do not use any drain saddle device.

OPTION A: BASEMENT ACCESS

INSTALLATION

Route the drain line (1/4″ black line)

DIRECTLY from the Reverse Osmosis system

to a standpipe in the basement, by-passing

the air gap provided in the faucet. The drain

line may also be routed in the basement to a

floor drain or washtub, provided that the air

gap in the basement is maintained. Avoid

dips, loops or low spots in the drain line.

The basement air gap and drain installation

configuration must conform to all local codes.

Special air gap fittings are available from

your local hardware store to connect the

drain line to the top of the standpipe.

Drain line from

Reverse Osmosis

by-passing faucet

air gap

Maintain air gap

at drain point

in basement

1/4″ Black

tubing

OPTION B: DRAIN LINE ADAPTER

INSTALLATION

CAUTION!

DO NOT INSTALL DRAIN LINE ADAPTER

DOWNSTREAM FROM DISPOSER.

Install the provided drain line adapter under the

sink as shown. The baffle-tee provided must be

in place (purchase and install if necessary) to

prevent a clog in the Reverse Osmosis drain

line. Route the drain line (3/8″ black) from the

faucet air gap to the drain line adapter, ensuring

that there are no dips, loops or low spots in the

line that could result in a clogged drain line.

The tubing must be cut to length to provide

a straight routing from the faucet to the drain.

Drain noise in the sink drain is normal when

the Reverse Osmosis system is operating.

FAUCET DRAIN TUBING AND WATER SUPPLY TUBING

If OPTION A: BASEMENT ACCESS INSTALLATION (see Filtration Drain Connection Installation section,

above) was used, go to Step 2.

If OPTION B: DRAIN LINE ADAPTER

INSTALLATION was used, connect the

faucet drain tubing by running the 3/8″

black tubing from the 3/8″ faucet barb

to the drain fitting (installed in Filtration

Drain Connection Installation section,

above). Keep this tubing run as short and

straight as possible, without loops, dips

or low spots. Cut the tubing as needed

and insert into the drain fitting.

To connect the water supply tubing:

Run the 1/4″ yellow tubing from the Reverse

Osmosis inlet to the feed water adapter

(see illustrations in the Feed Water Supply

section). Connect the tubing as applies (see

Feed Water Supply section) and tighten the

nut securely.

Drain line adapter

in different line

from disposer

HOT COLD

Disposer

Drain line is straight

Installation Instructions

REVERSE OSMOSIS SYSTEM ASSEMBLY

AND STORAGE TANK INSTALLATION

NOW THAT YOUR REVERSE OSMOSIS SYSTEM

IS INSTALLED…SANITIZE!

Sanitize upon installation and after servicing

inner parts, including replacement of prefilter,

postfilter and the Reverse Osmosis cartridge.

It is important to wash hands with anti-

bacterial soap before handling inner parts of

the system. See the Sanitization section.

CAUTION: If installing unit in new

construction, ensure that house plumbing is

flushed thoroughly before opening the water

supply valve. Also, before sanitizing, be sure

to remove all cartridges as described in the

Sanitization section. Chlorine will destroy the

Reverse Osmosis cartridge.

Hold the Reverse Osmosis assembly up

to the wall surface where you will install it.

Mark locations for the screws. The arrows

on the top of the bracket show the location

of the screw holes.

Connect the tubing to the storage tank: Run

the length of 3/8″ orange tubing from the

tee fitting on the Reverse Osmosis module

to the tank inlet fitting.

Wood screws are included for fastening

to a wood surface. Provide other screws

as needed.

Hang the Reverse Osmosis assembly

on the screws.

Apply pipe thread sealing tape to the tank

fitting. Insert into tank threads. Tighten with

a wrench.

Storage

tank

To faucet

Supply line

Orange tubing

2″ minimum clearance

for changing cartridges

Installation Instructions

PREFILTER, POSTFILTER AND RO CARTRIDGE

REPLACEMENT PROCEDURE, INCLUDING SANITIZATION

Turn OFF the icemaker (if attached to the

RO system).

Wash your hands with anti-bacterial soap.

Turn off water supply

to RO system.

Remove cap from RO cartridge housing

(unscrew tubing first, on some models).

Use pliers to remove the RO cartridge. Place

in a clean plastic bag or discard if replacing.

Thoroughly wipe inside of housing and cap

with a paper towel or dish brush moistened

with dish soap. Rinse well.

Turn on RO faucet. Drain tank (may take

several minutes). Turn off RO faucet.

CAUTION: Failure to close the water

supply valve or tank shutoff valve will cause

water to spray or run when sumps are

removed.

Remove the sumps.

Be careful—sumps will be

full of water.

Discard filters. Thoroughly

wash sumps with dish soap.

Thoroughly wipe inside of

heads with a paper towel

moistened with dish soap.

Rinse well.

Replace empty postfilter

sump.

Fill prefilter sump with water to within 1″

of O-ring. Add 2 oz. (4 Tbsp.) ordinary

household bleach. Replace prefilter sump.

Turn on water supply. Open RO faucet until

water begins to flow, then close. Allow

system to fill for 1 minute.

Open faucet and allow water to flow for 10

minutes. Close faucet for one minute more,

then open and allow water to flow for

another 10 minutes, or until bleach odor is

gone. Turn off water supply again. Drain RO.

Remove sumps. Insert filters.

Lubricate o-ring with food-grade

silicone grease, if necessary.

(Do not use petroleum jelly).

Tighten sumps securely.

Installation Instructions

PREFILTER, POSTFILTER AND RO CARTRIDGE

REPLACEMENT PROC., INCLUDING SANITIZATION

(cont.)

Remove cap from RO cartridge housing.

Install RO cartridge, O-ring end first.

Lubricate cover O-ring with food-grade

silicone grease, if necessary. (DO NOT use

petroleum jelly). Tighten cap securely.

Change the batteries in the filter change

indicator:

• Use a small, flat blade screwdriver or coin

and carefully open the battery compartment.

• Install the CR2032 battery (+) side down into

the tray.

• Slide the tray into the base and snap-lock

into place.

• The light will flash 5 times to indicate

proper installation. After 6 months of use,

the light will flash again, indicating the

proper time to replace the filter. Install a

new CR2032 battery after 6 months of use.

If you only replaced the prefilter and

postfilter, allow faucet to run 5 minutes to

remove harmless carbon particles. If you

replaced the RO cartridge, fill and empty

the storage tank three times, until taste

and odor from food grade membrane

preservative is gone.

Once storage tank is full, turn on icemaker.

Turn on water supply. Allow to fill. (May

take up to four hours). Check for leaks.

If you replaced the RO cartridge, also

replace the flow control and screen.

(Unscrew the black 1/4″ line from the fitting.

Remove flow control with clean knife edge.

Remove screen with a clean toothpick).

Tighten the nut hand-tight and then tighten

1/4 turn with pliers. DO NOT OVERTIGHTEN.

Flow

control

Screen

Compression

nut

1/4″ Black tubing

Care and cleaning of the reverse osmosis system.

ge.com

To obtain replacement filters, call toll-free GE Appliance Parts at 800.626.2002 (U.S.),

800.663.6060 (Canada–English), 800.361.3869 (Canada–French), or visit the store where

you purchased your reverse osmosis system.

CAUTION: Before servicing the Reverse Osmosis system, close the water supply/saddle valve

and open the RO water faucet. Allow the system to drain.

Prefilter/Postfilter Cartridge Replacement FX12P Carbon Block

Reverse Osmosis Cartridge Replacement FX12M Thin Film Polyamide

The Water Test Kit

To obtain an independent laboratory water test kit, please call Legend Technical Services at

1.800.826.8553 ext. 47 and leave your contact details. They will contact you to find out what water

tests you are interested in, and inform you of the cost of the testing. You will then receive a kit that

will include all necessary tests to properly indicate the performance level of your system. Product

water should be tested a minimum of every six months.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

Description of the Reverse Osmosis System

Prefilter—Water from the cold supply pipe is

directed to the prefilter cartridge, which is inside

the sump.

The prefilter is a replaceable sediment

cartridge containing activated carbon. The

cartridge removes sand, silt, dirt, other sediments

and up to 2.0 ppm of chlorine from the feed

water. The prefilter reduces chlorine in the feed

water because CHLORINE DESTROYS THE REVERSE

OSMOSIS MEMBRANE. Filtered, clean, chlorine-

reduced water flows from the prefilter to the

Reverse Osmosis cartridge.

Storage Tank—The storage area holds up to

3 gallons of product water. A diaphragm inside

the tank keeps water pressurized for fast flow

to the faucet when drinking water is needed.

Check Valve—A check valve is built into one end

of the Reverse Osmosis housing. The check valve

prevents a backward flow of product water from

the storage area. A backward flow could cause the

Reverse Osmosis membrane to rupture.

Automatic Shutoff Valve—To conserve water, the

drinking water system has an automatic shutoff.

When the storage tank has filled to capacity and

the drinking water faucet is closed, pressure closes

the shutoff. Water flow to the Reverse Osmosis

housing is shut off until drinking water is used

again, and pressure drops in the Reverse Osmosis

system.

About the reverse osmosis system.

What the Reverse Osmosis System Does

Reverse Osmosis removes Total Dissolved Solids

(TDS) and organic matter from water by diffusing

through a special membrane. The membrane

separates minerals and impurities from the water

and they

are flushed to the drain. High quality

product water goes directly to the drinking water

faucet or to the storage tank. The system makes

a good supply of drinking water each day; see

Specification Guidelines. How much it makes

depends on the feed water supply pressure,

temperature and quality.

The carbon prefilter and postfilter are replaceable

cartridges. The prefilter removes chlorine while

also filtering sediments. The postfilter removes any

other undesirable tastes and odors before you use

the water.

Troubleshooting Tips

Consumer Support

Troubleshooting Tips Installation Instructions

Safety InstructionsOperating Instructions

Sump

Postfilter

cartridge

Prefilter cartridge

Reverse Osmosis cartridge

Reverse Osmosis housing

Turn sump this way to remove

O-ring housing

Reverse Osmosis

housing cap

Sump

O-ring on top lip of sump

O-ring end

Check valve

Automatic

shutoff valve

Reverse Osmosis Cartridge—The cartridge, inside

the Reverse Osmosis housing, includes a tightly

wound, special membrane. Water is forced through

the cartridge where the membrane removes the

dissolved solids and organic matter. High quality

product water exits the Reverse Osmosis housing

and goes to the storage tank. Reject water, with

the dissolved solids and organic matter, leaves the

housing and is discharged to the drain through

tubing.

Postfilter—After leaving the storage area,

but before going to the system faucet, product

water goes to the postfilter which is inside the

sump. The postfilter is also a replaceable

sediment cartridge that contains activated

carbon. Any remaining tastes, odors or

sediments are removed from product water

by the postfilter. Clean, high quality drinking

water flows through the tubing and to the

system faucet.

System Monitor—

A timer is provided in the faucet

base to remind you when it is time to replace

your prefilter and postfilter. Replace the filters

when the blue light begins to flash in order to

protect the RO membrane and keep the system

functioning properly. Be sure to remove and

replace the battery at the same time to reset

the timer.

Flow Control—The flow control regulates the flow

of water through the Reverse Osmosis cartridge

at the required rate to produce high quality

water. The control is located in the Reverse

Osmosis housing drain port. A small, cone-

shaped screen fits over the front end of the flow

control to prevent clogging due to sediments in

drain water. The flow control and screen should

be replaced each time the Reverse Osmosis

membrane cartridge is changed.

ge.com

Screen

Flow control

1/4″ black tubing

(to drain)

Consumer Support

Troubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Before you call for service…

Problem Possible Causes What To Do

Sounds you might hear Running water from the unit • This is normal.

to a drain.

Water has air bubbles Air in system after installation. • Will go away after water runs for a while.

and is cloudy

Chlorine taste and/or The ppm of chlorine in your

• If the water supply contains more than 2.0 ppm of

odor in the Reverse water supply exceeds maximum

chlorine,

additional filtering of the water supply to the

Osmosis product water limits and has destroyed the Reverse Osmosis is needed. Correct this condition before

Reverse Osmosis membrane. doing maintenance on the Reverse Osmosis system.

The prefilter is no longer • Replace the Reverse Osmosis membrane cartridge,

removing chlorine from flow control, screen, prefilter and postfilter.

the water supply.

Other taste and/or odor High quality product water • This is normal.

may have a different taste

than what you’re used to.

Low water usage. • Completely drain system and allow to refill.

Contamination in product

•

Use sanitizing procedures.

water storage.

Prefilter and postfilter

• Replace the prefilter and postfilter. If taste and odor

need to be changed and/or persists, replace the Reverse Osmosis cartridge, flow

the Reverse Osmosis cartridge control and screen.

needs to be changed.

Water leaking from Drain side of faucet air gap • Inspect and eliminate restriction or plug. It is important

faucet air gap hole (3/8″ tubing) plugged, restricted that there are no dips, loops or low spots in the drain line

or incorrectly connected to the from the faucet air gap to the drain pipe. Refer to the

drain point. Filtration Drain Connection Installations section, for proper

drain connection. If drain line adapter was used as the

drain point, periodic inspection/cleaning is recommended.

System makes product This is normal. • Water flow rate will be lower than your regular faucet.

water slowly

Water supply to the Reverse • Increase water pressure, precondition the water, etc.,

Osmosis system not within as needed to conform to specification guidelines before

specifications. doing maintenance on the Reverse Osmosis system.

Prefilter cartridge plugged • Replace the prefilter and postfilter.

If rate does not

with sediments and/or the

increase,

replace the Reverse Osmosis cartridge, flow

Reverse Osmosis cartridge control and screen.

plugged with sediments.

Faucet light blinking Prefilter and postfilter • Replace filters. Don’t forget to sanitize the system when

need replacing. replacing filters.

Timer was not reset when filters • Remove and replace battery in faucet base.

were replaced.

Six months have passed Battery may be dead. • Replace battery. NOTE: Replacing battery resets the

and faucet light is not six-month timer, so be sure to replace prefilter and

blinking postfilter if it is time to do so.

Battery may have been • Any time the battery is removed and reinserted, the

removed recently. six-month timer starts over again. Do not remove battery

unless you wish to restart the timer.

Troubleshooting Tips

Save time and money! Review the chart first and you may

not need to call for service.

* NOTE: Codes in the State of Massachusetts require installation by a licensed plumber

and do not permit the use of the saddle valve. For installation, use plumbing code 248-CMR

of the Commonwealth of Massachusetts.

Parts list.

ge.com

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

Optional Accessories

Consumer Support Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

General Electric parts catalog.

REF. NO. PART NO. PART DESCRIPTION GXRM10GBL

0001 WS15X10037 FAUCET BODY & SPOUT 1

0002 WS22X10037 3/8″ QUICK CONNECT—FAUCET 1

0003 WS22X10005 1/4″ NUT 10

0004 WS22X10026 3/8″ NPT X 1/4″ NUT ELBOW 2

0005 WS22X10006 1/4″ TUBE INSERT 8

0006 WS22X10038 VALVE—AUTO SHUT OFF 1

0007 WS22X10039 1/4″ X 3/8″ X 3/8″ TUBE TEE 1

0008 WS22X10008 3/8″ NUT 4

0009 WS22X10007 3/8″ TUBE INSERT 4

0010 WS22X10040 CHECK VALVE—1/4″ INSERT 1

0011 WS22X10041 1/8″ NPT X 1/4″ FITTING 1

0012 WS03X10016 FLOW CONTROL 1

0013 WS03X10015 CONE SCREEN 1

0014 WS22X10002 3/8″ NPT X 3/8″ NUT ELBOW 2

0015 FX12M RO MEMBRANE 1

0016 WS03X10045 O-RING—RO MEMBRANE HSNG 1

0017 WS31X10025 CAP—RO MEMBRANE HSNG 1

0018 WS22X10042 1/8″ NPT X 1/4″ FITTING 1

0019 WS22X10043 ELBOW—1/4″ STEM X 1/4″ 1

0020 WS20X10006 HOUSING—RO MEMBRANE 1

0021 WS28X10039 BRACKET 1

0022 WS22X10044 CONNECTOR—3/8″ X 3/8″ MNPT 1

0023 WS32X10019 STORAGE TANK 1

0024 WX5X140 WRENCH 1

0025 WS03X10038 O-RING, SUMP HOUSING 2

0026 FX12P CARBON BLOCK CARTRIDGE 2

0027 WS20X10007 SUMP HOUSING 2

0028 WS18X10006 DRAIN LINE ADAPTER—DLA9 1

0029 WS18X10009 ADAPTER KIT—FEED WATER 1

0030 WS10X10028 FAUCET BASE ASM 1

0031 WS02X10031 WASHER & NUT—FAUCET 1

0033 WS02X10032 SCREWS, BRACKET 8

0034 WS31X10026 HOUSING HEAD 2

0035 WS15X10023 SADDLE VALVE 1

0036 WS07X10018 TUBING—1/4″ X 33′—WHITE 1

0037 WS07X10019 TUBING—3/8″ X 33′—WHITE 1

0038 WS01X10013 NITRATE TEST STRIP 1

0039 WS02X10033 MOUNTING SCREWS 2

9999 49-50199 OWNER’S MANUAL/INSTALLATION 1

INSTRUCTIONS

* NOTE: Codes in the State of Massachusetts require installation by a licensed plumber

and do not permit the use of the saddle valve. For installation, use plumbing code 248-CMR

of the Commonwealth of Massachusetts.

To obtain replacement parts, call toll-free 800.626.2002 (U.S.), 800.663.6060 (Canada–English),

800.361.3869 (Canada–French).

Notes.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Consumer Support Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

GE Reverse Osmosis System Warranty.

For The Period Of: GE Will Replace:

One Year Any part of the Reverse Osmosis Filtration System which fails due to a defect in materials or

From the date of the workmanship. During this limited one-year warranty, GE will also provide, free of charge, all labor

original purchase and related service to replace the defective part.

All warranty service provided by our SmartWater

™

Authorized

Servicer Network. To schedule service on-line, 24 hours a day,

866.777.7627 (Canada). Please have serial number and model

number available when calling for service.

■ Service trips to your home to teach you how to use the

product.

■ Improper installation, delivery or maintenance.

■ Failure of the product if it is abused, misused, used for

other than the intended purpose or used commercially.

■ Use of this product where water is microbiologically

unsafe or of unknown quality, without adequate

disinfection. Systems certified for cyst reduction may be

used on disinfected water that may contain filterable cysts.

■ Filter cartridges, membrane cartridges and batteries after

30 days from date of purchase.

■ Damage to the product caused by accident, fire, floods

or acts of God.

■ Incidental or consequential damage caused by possible

defects with this appliance.

What GE Will Not Cover:

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use

within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may

be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for

service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period allowed by law.

La page charge ...

GE Water Dispenser GXRM10GBL Manuel utilisateur

Marque: GE

Modèle: Water Dispenser GXRM10GBL

Catégorie: Articles sanitaires

Taper: Manuel utilisateur

Ce manuel convient également à

GXRM10GBL

Télécharger le PDF

rapport

dans d''autres langues

English: GE Water Dispenser GXRM10GBL User manual
español: GE Water Dispenser GXRM10GBL Manual de usuario

GE Water Dispenser GXRM10GBL Manuel utilisateur

Ce manuel convient également à

GE Water Dispenser GXRM10GBL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents