DeWalt DW079LRK Manuel utilisateur

Marque: DeWalt

Modèle: DW079LRK

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

Dúvidas? Visite-nos na Internet em www.D

eWALT.com.br

1-800-4-DeWALT

Instruction Manual

Guide d’utilisation

Manual de instrucciones

Manual de Instruções

DW074LR, DW079LR, DW079LG

Rotary Laser

Laser rotatif

Láser rotativo

Laser Rotativo

Final page size: A5 (148mm x 210mm)

DW074_DW079 User Manual - NA - TRANSLATED.indd 1 5/17/2018 2:05:26 PM

English 8

Français 18

Español 29

Português 40

DW074_DW079 User Manual - NA - TRANSLATED.indd 2 5/17/2018 2:05:26 PM

745

3 61 8

DW079LR/DW079LG

3 61 8

DW074LR

RPM

˚/45˚/90˚

DW074_DW079 User Manual - NA - TRANSLATED.indd 3 5/17/2018 2:05:27 PM

LEVEL MODE

MODE NIVEAU

MODO DE NIVEL

MODO DE

NIVELAMENTO

PLUMB MODE

MODE APLOMB

MODO DE PLOMADA

MODO NIVELAMENTO

VERTICAL

LEVEL MODE/MODE NIVEAU/MODO DE NIVEL/

MODO DE NIVELAMENTO

PLUMB MODE/MODE APLOMB /MODO DE PLOMADA/

MODO NIVELAMENTO VERTICAL

5/8-11"

E F

DW074_DW079 User Manual - NA - TRANSLATED.indd 4 5/17/2018 2:05:28 PM

INDICATORS/INDICATEURS /INDICADORES/INDICADORES

Above Grade/

Au-dessus du niveau /

Por encima del nivel

Acima do grau

Slightly Above Grade/

Légèrement au-dessus du niveau /

Ligeramente por encima del nivel/

Ligeiramente acima do grau

On Grade/

Au niveau /

En nivel/

Um grau

Slightly below Grade/

Légèrement au-dessous du niveau /

Ligeramente por debajo del nive/

Ligeiramente abaixo do graul

Below Grade/

Au-dessous du niveau /

Por debajo del nivel/

Abaixo do grau

audible signals/

signal sonore /

señales auditivas/

sinais audíveis

fast beep /

bip rapide /

bip rápido/

Bipe rápido

fast beep /

bip rapide /

bip rápido/

Bipe rápido

steady tone/

tonalité constante /

tono constante/

Tom estável

slow beep/

bip lent /

bip lento/

Bipe lento

slow beep/

bip lent /

bip lento/

Bipe lento

display icons/

icône affichée /

íconos en pantalla/

ícones da tela

DW074_DW079 User Manual - NA - TRANSLATED.indd 5 5/17/2018 2:05:29 PM

DW074_DW079 User Manual - NA - TRANSLATED.indd 6 5/17/2018 2:05:30 PM

BEAM

FAISCEAU

RAYO

RAIO

Marks on walls

Repères sur les murs

Marcas en la pared

Marcas na parede

LASER UNIT ROTATED 180˚

ROTATION DE L’APPAREIL LASER A 180˚

UNIDAD LÁSER ROTADA EN 180º

UNIDADE DE LASER EM ROTAÇÃO DE 180º

BEAM

FAISCEAU

RAYO

RAIO

Q R

DW074_DW079 User Manual - NA - TRANSLATED.indd 7 5/17/2018 2:05:31 PM

English

ENGLISH

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of

personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

If you have any questions or comments about this or any

DeWALT

tool, call us toll free at: 1-800-4-

DeWALT

(1-800-433-9258).

Warning: To reduce the risk of injury, user must read instruction manual.

Safety Instructions for Lasers

WARNING! Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE



WARNING! Laser Radiation Exposure. Do not disassemble or modify the laser level. There are no user serviceable

parts inside. Serious eye injury could result.



WARNING: Hazardous Radiation. Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

• Do not operate the laser in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or fumes.

• Use the laser only with the specifically designated batteries. Use of any other batteries may create a risk of fire.

• Store idle laser out of reach of children and other untrained persons. Lasers are dangerous in the hands of untrained

users.

• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for

one laser, may create a risk of injury when used on another laser.

• Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified

personnel may result in injury. To locate your nearest

DeWALT

service center call 1–800–4-

DeWALT

(1–800–433–9258) or go

to http://www.

DeWALT

.com on the Internet.

• Do not use optical tools such as a telescope or transit to view the laser beam. Serious eye injury could result.

• Do not place the laser in a position which may cause anyone to intentionally or unintentionally stare into the laser

beam. Serious eye injury could result.

• Turn the laser off when it is not in use. Leaving the laser on increases the risk of staring into the laser beam.

• Do not position the laser near a reflective surface which may reflect the laser beam toward anyone’s eyes. Serious eye

injury could result.

• Do not operate the laser around children or allow children to operate the laser. Serious eye injury may result.

• Do not remove or deface warning labels. Removing labels increases the risk of exposure to radiation.

ROTARY LASER

DW074LR, DW079LR, DW079LG

DW074_DW079 User Manual - NA - TRANSLATED.indd 8 5/17/2018 2:05:31 PM

ENGLISH

• Position the laser securely on a level surface. Damage to the laser or serious injury could result if the laser falls.



WARNING: Use of controls or adjustments or performance of procedures other than those specified herein may result in

hazardous radiation exposure.



WARNING! DO NOT DISASSEMBLE THE ROTARY LASER. There are no user serviceable parts inside.

Disassembling the rotary laser will void all warranties on the product. Do not modify the product in any way.

Modifying the tool may result in hazardous laser radiation exposure.

• The label on your tool may include the following symbols.

V ........................volts

mW ....................milliwatts

........ laser warning symbol

nm..........wavelength in nanometers

3R .......... Class 3R Laser

Warning Labels

For your convenience and safety, the following label is on your laser.

WARNING: To reduce the risk of injury, user must read instruction manual.

WARNING: LASER RADIATION. DO NOT STARE INTO BEAM. Class 3R Laser Product

AVOID EXPOSURE -LASER RADIATION IS EMITTED FROM THIS APERTURE

DW074_DW079 User Manual - NA - TRANSLATED.indd 9 5/17/2018 2:05:32 PM

ENGLISH

Laser Information

The DW074LR and DW079LR/LG Cordless Rotary Lasers are

CLASS 3R laser products and comply with 21 CFR 1040.10

and 1040.11 except for deviations pursuant to laser notice

No. 50, dated June 24, 2007.

Conforms to UL STDS 61010-1 & 2595

Certified to CSA STD C22.2 No. 61010-1

Complies with IEC 60825-1:2014

These devices comply with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: 1) this

device may not cause harmful interference, and 2) this device

must accept any interference received, including interference

that may cause undesired operation.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio and television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

differentfrom that which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Canada, Industry Canada (IC) Notices

Class B digital circuitry of this device complies with Canadian

ICES-003. This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to the following

two conditions: 1) this device may not cause interference,

and 2) this device must accept any interference, including

interference that may cause undesired operation of the device.

READ ALL INSTRUCTIONS

Batteries and Power

This

DeWALT

rotary laser will accept all

DeWALT

20 volt

lithium ion batteries, but is built to best resist damage during a

fall when used with the following batteries: All 1.5Ah and 2Ah

DeWALT

20 volt lithium ion batteries.

Charging the Battery

The battery pack is not fully charged out of the carton. You

need to use a

DeWALT

20 volt charger to charge the battery

pack before you can use the rotary laser.

• Refer to the chart at the end of this manual for compatibility

of chargers and battery packs.

• Be sure to read all safety instructions before using your

charger.



WARNING:

• DO NOT attempt to charge the battery pack

with any chargers other than the ones listed

in this manual. The charger and battery pack are

specifically designed to work together.

• Carefully follow all instructions and warnings on

the battery label and package and accompanying

Battery Safety Manual.

1. Slide the battery pack into the charger as described in the

Battery Safety Manual.

2. Wait until the battery pack is fully charged.

3. Slide the battery pack out of the track.

NOTE: When ordering replacement battery packs, be sure to

include the catalog number and voltage.

Installing the 20V

DeWALT

Battery Pack

1. Position the fully-charged 20V

DeWALT

battery pack so the

release button (Figure

) is facing away from you and

to the right.

2. Press and hold down the release button on the battery

pack.

3. Slide the battery pack all the way into the track on the side

of the laser.

4. Release the button on the battery pack.

Removing the Battery Pack

1. Press and hold the release button on the battery pack.

2. Slide the battery pack out of the track on the laser.

3. Release the button on the battery pack.

4. To recharge the battery pack, insert it into the charger, as

described in the Battery Safety Manual.



WARNING: Batteries can explode or leak, and can

cause injury or fire. To reduce this risk, follow the

instructions in the Battery Safety Manual.

Storing Battery Packs

• The best storage place is one that is cool and dry, and

away from direct sunlight and excess heat or cold.

• Long storage will not harm the battery pack or charger.

Under proper conditions, they can be stored for 5 years

or more.

DW074_DW079 User Manual - NA - TRANSLATED.indd 10 5/17/2018 2:05:32 PM

ENGLISH

SAVE THESE INSTRUCTIONS FOR FUTURE USE

User Safety

Personal Safety

• Stay alert, watch what you are doing, and use common

sense when operating a laser product. Do not use

the tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention while

operating laser products may result in serious personal

injury.

• Use appropriate personal protective equipment,

including eye protection when working in a construction

environment.

Tool Use and Care

• Do not use the tool if the switch does not turn it on or

off. Any tool that cannot be controlled with the switch is

dangerous and must be repaired.

• Store idle laser products out of the reach of children

and do not allow persons unfamiliar with the laser

product or these instructions to operate the laser

product. Laser products are dangerous in the hands of

untrained users.

• Use only accessories that are recommended by the

manufacturer for your model. Accessories that may be

suitable for one tool, may become hazardous when used

with another tool.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-ion

batteries (or battery packs) indicates that the

costs to recycle these batteries (or battery

packs) at the end of their useful life have already been paid

DeWALT

. In some areas, it is illegal to place spent nickel

cadmium, nickel metal hydride or lithium-ion batteries in the

trash or municipal solid waste stream and the Call 2 Recycle®

program provides an environmentally conscious alternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride or

lithium-ion batteries to an authorized

DeWALT

service center

or to your local retailer for recycling. You may also contact

your local recycling center for information on where to drop off

the spent battery. RBRC® is a registered trademark of Call 2

Recycle, Inc.

Operation

Operating Tips

• To extend battery life per charge, turn the laser off when it

is not in use.

• To ensure the accuracy of your work, check the laser

calibration often. Refer to Calibrating the Laser.

• Before attempting to use the laser, make sure the tool is

positioned on a relatively smooth, secure surface.

• Always mark the center of the laser line or dot. If you

mark different parts of the beam at different times you will

introduce error into your measurements.

• To increase working distance and accuracy, set up the

laser in the middle of your working area.

• When attaching to a tripod or wall, mount the laser

securely.

• When working indoors, a slow rotary head speed will

produce a visibly brighter line, a faster rotary head speed

will produce a visibly solid line.

• To increase beam visibility, wear Laser Enhancement

Glass es and/or use a Laser Target Card to help find the

beam.

• Extreme temperature changes can cause movement or

shifting of building structures, metal tripods, equipment,

etc., which can effect accuracy. Check your accuracy often

while working.

• When working with the

DeWALT

Digital Laser Detector, set

the laser’s rotation speed to the fastest setting.

• If the laser is dropped or has suffered a sharp blow, have

the calibration system checked by a qualified service

center before using the laser.

Control Panel (Fig.

)

The laser is primarily controlled by the power button

, the

mode button

, the speed button

and the scan mode button

. These features are then modified when used with either the

Axis selection button

(DW079LR/LG in Slope mode only), or

the two direction/elevation adjustment buttons

and

The direction/elevation adjustment buttons control the rotational

direction of the laser head as well as adjust the elevation of the

beam when the unit is in slope mode. These buttons can also

be used to incrementally rotate the beam when the unit is in

Scan mode.

The buttons on the DW074LR control panel, DW079LR/

DW079LG control panel, and the DW079LR/DW079LG Remote

keypad all work the same, unless otherwise indicated.

DW074_DW079 User Manual - NA - TRANSLATED.indd 11 5/17/2018 2:05:32 PM

ENGLISH

Power Button

The Power button is used to turn the laser unit on and off.

• To power ON the DW074LR or DW079LR/LG laser unit,

press the Power button once.

• To completely power OFF the DW074LR or DW079LR/LG

laser unit, press the power button for 3 sec.

Speed/Rotation Button

The speed button

is used to adjust the rotation speed of the

laser beam through its 4 preset speeds (150, 300, 600, and

1200 RPM).

Scan Mode Button

15˚/45˚/90˚

The scan mode button

is used to make the laser head

sweep back and forth, creating a short, bright laser line. This

short line is much brighter and more visible than when the unit

is in full rotation mode.

Using Scan Mode

• To enter Scan Mode, push and release the scan mode

button

. To cycle through the scan angles, continue to

press the button until you reach the desired angle.

• The direction of the scan zone can be controlled with the

arrow buttons

and

Slope Mode Button

• To activate Slope Mode press the slope mode button

• To return to self-leveling mode and re-engage full self-

leveling, press and hold the mode button

again.

Setting the Slope Direction

When Slope Mode is activated, the unit automatically engages

the X- Axis. This allows you to slope the laser in the direction of

the X-Axis, as indicated by the “gunsights” on the rollcage.

The LED light

indicates the current slope direction.

DW079LR/LG only: In certain situations, it may be desirable

to slope the laser in the Y-axis. The direction of Slope Mode

can be changed back and forth between the Y-axis and the

X-axis by pressing the X-Y axis button

. The selected axis is

identified by LED light

Setting the Amount of Slope

1. Turn on Slope Mode.

2. Select the desired axis.

3. Use the Arrow buttons (Fig.

and

) to tilt the laser

rotor head up and down.

- Each quick press of an Arrow button will move the slope

by 0.01º (1/16" @ 30ft. or 1.6mm @ 10m).

- If you press and hold an Arrow button between 2 sec-

10 sec, the slope will move from .0.01º/sec to 0.2º/sec.

- If you press and hold an Arrow button longer than 10

sec, the slope will move 0.2º/sec.

Arrow Buttons (Fig.

)

The arrow buttons (

and

) are used for different

functions depending on the operating mode of the laser unit.

• In Self-Leveling Horizontal Mode, the arrow buttons

rotate the direction of the laser beam clockwise or counter-

clockwise during rotation, or adjust the position of the laser

beam clockwise or counter-clockwise during Scan Mode.

• In Self-Leveling Vertical Mode, the arrow buttons rotate

the direction of the laser beam clockwise or counter-

clockwise during rotation, or adjust the position of the laser

beam clockwise or counter-clockwise during Scan Mode.

• In Slope Mode, the arrow buttons are used to tilt the

laser head.

Turning the Laser On (Fig.

)

1. Insert the fully charged 20V battery pack as shown in

Figure

2. Gently press the power button

to power ON the laser.

- The power LED indicator light

will illuminate

- Self-leveling mode is activated automatically and

the laser unit will self-level. Once the laser unit is

level, the beam will rotate once at 600 RPM in the

clockwise direction.

- After 10 sec., Hi Mode (Anti- Drift) is activated

automatically and the Hi LED

will illuminate.

3. Press the speed/rotation button

to adjust the rotation

speed. The direction can be changed using buttons

and

4. Press the Scan button

to set the laser to scan in 0°, 15°,

45°, or 90° degree mode.

If you turn ON Slope Mode, the Slope LED

(

)

will light. If using

X-axis leveling, the X-axis LED

(

)

will light, or if using Y-axis

leveling, the Y-axis LED

(

)

will light instead.

Calibrating the Laser (Fig. O, P)

Field calibration checks should be done frequently. This section

provides instructions for performing simple field calibration

checks of your

DeWALT

Rotary Laser. Field calibration checks

do not calibrate the laser. That is, these checks do not correct

errors in the leveling or plumbing capability of the laser. Instead,

the checks indicate whether or not the laser is providing a

correct level and plumb line. These checks cannot take the

place of professional calibration performed by a

DeWALT

service center.

DW074_DW079 User Manual - NA - TRANSLATED.indd 12 5/17/2018 2:05:33 PM

ENGLISH

Level Calibration Check (X-axis)

1. Set up a tripod between two walls that are at least 50 feet

apart. The exact location of the tripod is not critical.

2. Mount the laser unit on the tripod so that the X-axis points

directly toward one of the walls.

3. Turn the laser unit on and allow it to self-level.

4. Mark and measure points A and B on the walls as shown

in Figure O.

5. Turn the entire laser unit 180º so the X-axis points directly

toward the opposite wall.

6. Allow the laser unit to self-level, and mark and measure

points AA and BB on the walls as shown in Figure P.

7. Calculate the total error using the equation:

Total Error = (AA – A) – (BB– B)

8. Compare total error to the allowable limits shown in the

following table.

Distance

Between Walls

Allowable Error

DW074LR

Allowable Error

DW079LR/DW079LG

40 ft. 3/32" 3/64"

50 ft. 1/8" 1/16"

70 ft. 5/32" 3/32"

100 ft. 1/4" 1/8"

Level Calibration Check (Y-axis)

Repeat the procedure above, but with the laser unit positioned

so the Y-axis is pointed directly toward the walls.

Plumb Error Check (Fig. Q)

1. Using a standard plumb bob as a reference, mark the top

and bottom of a wall. (Be sure to mark the wall and not the

floor and ceiling.)

2. Position the rotary laser securely on the floor approximately

3' (1 m) from the wall.

3. Turn the laser on, and point the dot at the mark on the

bottom of the wall. Then, using the up/down arrows on the

remote control, rotate the dot upwards. If the center of the

dot scans over the mark on the top of the wall, the laser is

properly calibrated.

NOTE: This check should be done with a wall no shorter than

the tallest wall for which this laser will be used.

Using the Laser on a Tripod (Fig.

)

1. Position the tripod securely and set it to the desired height.

2. Make sure that the top of the tripod is roughly level. The

laser will self-level only if the top of the tripod is within ± 5˚

of level. If the laser is set up too far out of level, it will beep

when it reaches the limit of its leveling range. No damage

will be done to the laser, but it will not operate in an “out of

level” condition.

3. Secure the laser to the tripod by attaching the tripod

adapter

as shown in Figure

to the laser body. The

adapter may be assembled to the bottom for level mode

or to the side for plumb mode. Place the assembly on the

tripod and screw the threaded knob on the tripod into the

female thread on the tripod adapter.

NOTE: Be sure that the tripod you are working with has a

5/8"–11 threaded screw to ensure secure mounting.

4. Turn the laser on and adjust the rotation speed and controls

as desired.

Using the Laser on a Floor (Fig.

)

The laser level can be positioned directly on the floor for

leveling and plumbing applications such as framing walls.

1. Place the laser on a relatively smooth and level surface

where it will not be disturbed.

2. Position the laser for a level or plumb setting as shown.

3. Turn the laser on and adjust the rotation speed and controls

as desired.

NOTE: The laser will be easier to set up for wall applications if

the rotation speed is set to 0 RPM and if the remote control is

used to line up the laser with control marks. The remote allows

one person to set up the laser.

Using the DW079LR/LG Remote

The remote control allows one person to operate and set up

the laser from a distance. The LED light on the remote control

indicates a signal is being transmitted from the DW079LR/LG

laser unit. You can use all the buttons on the keypad to control

that laser unit.

If your DW079LR/LG laser unit was stamped on or after 2016-

49-NZ, you can use the Remote to completely power OFF the

laser unit.

2016-49-NZ

To completely power OFF a DW079LR/LG laser unit (stamped

on or after 2016-49-NZ) using the Remote keypad, press the

X-Y axis button

(

)

and the MODE button

(

)

simultaneously.

DW074_DW079 User Manual - NA - TRANSLATED.indd 13 5/17/2018 2:05:34 PM

ENGLISH

Specifications

SKU DW074LR DW079LR DW079LG

Laser Wavelength 630-680nm 630-680nm 515-530nm

630-680nm

Laser Power/Class ≤5mw /

CLASS 3R

≤ 5mw /

CLASS 3R

≤ 5mw /

CLASS 3R

Rotation Speed 150, 300, 600,

1200 RPM

150, 300, 600,

1200 RPM

150, 300, 600,

1200 RPM

Self-Leveling Range ± 5° ± 5° ± 5°

Indoor Visibile Range 150' (45 m)

diameter

200' (60 m)

diameter

250' (80 m)

diameter

Range with Detector 1500' (450 m)

diameter

2000' (600 m)

diameter

2000' (600 m)

diameter

Leveling Accuracy

(@ 600 RPM)

± 1/8" per 100' (±

3 mm per 30 m)

± 1/16” per 100’

(± 1.5 mm per

30m

± 1/16” per 100’

(± 1.5 mm per

30m

Power Source 20V D

WALT

batteries

20V D

WALT

batteries

20V D

WALT

batteries

Operating Temperature 23°F to 122°F

(-5°C to 50°C)

23°F to 122°F

(-5°C to 50°C)

23°F to 122°F

(-5°C to 50°C)

Storage Temperature -4°F to 158°F

(-20°C to 70°C)

-4°F to 158°F

(-20°C to 70°C)

-4°F to 158°F

(-20°C to 70°C)

Environmental Water resistant Water resistant Water resistant

Accessories

Recommended accessories for use with your tool are available

for purchase at your factory-owned local service center.



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with this

product.

If you need assistance in locating any accessory, please

contact

DeWALT

Industrial Tool Co., 701 East Joppa Road,

Towson, MD 21286, call 1–800–4-

DeWALT

(1–800–433–9258)

or visit our website www.

DeWALT

.com

Digital Laser Detector (Fig.

–

)

Some laser kits include a

DeWALT

Digital Laser Detector. The

DeWALT

Digital Laser Detector allows you to locate a laser

beam emitted by a rotary laser in bright light conditions or over

long distances. The detector can be used in both indoor and

outdoor situations where it is difficult to see the laser beam.

The detector is not for use with non-rotating lasers but is

compatible with most rotary red-beam (DW0743R) and green

beam (DW0743G) lasers. It can be set to indicate the location

of the beam to either the nearest 1/8" (3 mm) or the nearest

1/25" (1 mm). The detector gives both visual signals through

the display window

and audio signals through the speaker

to indicate the location of the laser beam.

The

WALT Digital Laser Detector can be used with or without

the detector clamp. When used with the clamp, the detector can

be positioned on a grade rod, leveling pole, stud or post.

Installing a Battery in the Detector (Fig.

)

The Digital Laser Detector is powered by a 9 volt battery. To

install the battery provided, lift up on the battery compartment

cover

. Place the 9 volt battery in the compartment, aligning

the battery as shown.

Detector Controls (Fig.

)

The detector is controlled by the power button

and the

accuracy mode button

When the power button is pushed once, the detector is turned

on. The top of the display window shows the accuracy icon

, and the volume icon

. To decrease the volume of the

audible signal that the detector emits when it senses a laser

beam, push the button again; one of the half circles next to the

horn icon will dissappear. To turn off the audible signal push the

button a third time; the volume icon will dissapear. The

DeWALT

Digital Laser Detector also has an auto shut-off feature. If a

rotary laser beam does not strike the beam detection window,

or if no buttons are pressed, the detector will shut itself off in

about 30 minutes.

When the detector is on, the top of the window shows an

accuracy mode icon. Either the ±1/25" (1 mm) accuracy mode

icon

will appear, or the ±1/8" (3 mm) accuracy mode icon

will appear. When the ±1/25" (1 mm) accuracy mode icon

appears, it indicates that the detector will give an “on grade”

reading only when the laser beam is on grade or no more

than 1/25" (1 mm) above or below it. When the 1/8" (3 mm)

accuracy mode icon appears, it indicates that the detector will

give an “on grade” reading when the laser beam is on grade

or approximately 1/8" (3 mm) above or below it. Push the

accuracy mode button

once to change the accuracy mode.

Detector Operation (Fig.

)

1. Set up and position the rotary laser that you will be using

according to the manufacturer’s directions. Turn the laser

on and make sure that the laser is rotating and emitting a

laser beam. NOTE: This detector has been designed to be

used only with a rotating laser. The detector will not work

with a stationary beam laser level.

2. Turn the detector on by pressing the power/volume

button

3. Adjust the volume as desired as described in the

Detector Controls.

4. Position the detector so that the detector window

facing the laser beam produced by the rotary laser. Move

the detector up or down within the approximate area of the

beam, until you have centered the detector. For information

about the display window indicators and the audible signal

indicators, refer to the table titled Indicators (Fig.

5. Use the marking notches

to accurately mark the

position of the laser beam.

DW074_DW079 User Manual - NA - TRANSLATED.indd 14 5/17/2018 2:05:34 PM

ENGLISH

Detector Cleaning and Storage

• Dirt and grease may be removed from the exterior of the

detector using a cloth or soft, non-metallic brush.

• The D

eWALT

Digital Laser Detector is waterproof. If you

should drop the detector in mud, wet concrete, or a similar

substance, simply hose the detector off. Do not use high

pressure water, e.g., from a pressure washer.

• The best storage place is one that is cool and dry–away

from direct sunlight and excess heat or cold.

Detector Service

Except for batteries, there are no user serviceable parts in the

Digital Laser Detector. Do not disassemble the unit. Unauth-

orized tampering with the laser detector will void all warranties.

Detector Troubleshooting

The detector will not turn on.

• Press and release the power/volume button.

• Check to see that the battery is in place and in the

proper position.

• If the detector is very cold, allow it to warm up in a

heated area.

• Replace the 9 volt battery. Turn the unit on.

• If the detector still does not turn on, take the detector to a

DeWALT

service center.

The detector’s speaker makes no sound.

• Ensure that the detector is on.

• Press the power/volume button. It will toggle from high, to

low, to mute.

• Ensure that the rotary laser is spinning and that it is emitting

a laser beam.

• If the detector is still not making any sound, take it to a

DeWALT

service center.

The detector does not respond to a stationary laser beam.

The

DeWALT

Digital Laser Detector has been designed to work

only with rotary lasers.

The detector gives off a tone but the LCD display window

does not function.

• If the detector is very cold, allow it to warm up in a

heated area.

• If the LCD display window is still not functioning, take the

detector to a

DeWALT

service center.

Mounting Bracket (Fig.

)

Some laser kits include a Wall Mount. It can be used for

attaching the tool to track or ceiling angle and to aid in

acoustical ceiling installation. Follow the directions below for

using the wall mount.



CAUTION: Before attaching the laser level to wall

track or ceiling angle, be sure that the track or angle is

properly secured.

1. Place the laser on the mounting base

aligning the 5/8–

11 screw hole on the tripod adapter (

, Fig.

) attached

to the bottom of the laser with the hole

in the mounting

base. Turn the mounting knob

to secure the laser.

2. With the wall mount measuring scale

facing you, loosen

the wall mount clamp locking knob

to open the clamp

jaws.

3. Position the clamp jaws around the wall track or ceiling

angle and tighten the wall mount clamp locking knob

to close the clamp jaws onto the track. Be sure that

the wall mount clamp locking knob is securely tightened

before proceeding.



CAUTION: Always use a ceiling wire hanger or

equivalent material, in addition to the wall mount

clamp locking knob, to help secure the laser level

while mounting it to a wall. Thread the wire through

the handle of the laser level. DO NOT thread the wire

through the protective metal cage. Additionally, screws

may be used to fasten the wall mount directly to the

wall as a back up. Screw holes

43

are located at the

top of the wall mount.

4. Using the base leveling knob

approximate a level

position from the wall.

5. The tool can be adjusted up and down to the desired offset

height for working. To change the height, loosen the locking

knob

located on the left of the wall mount. Support the

mounting base when adjusting the height.

6. Turn the adjustment knob

, located to the right of the

wall mount, to move the laser level up and down to set your

height. Use the wall mount measuring scale

to pinpoint

your mark.

NOTE: It may be helpful to turn the power on and turn the

rotary head so that it puts a dot on one of the laser scales.

The

DeWALT

target card is marked at 1–1/2" (38 mm),

therefore, it may be easiest to set the offset of the laser to

1–1/2" (38 mm) below the track.

7. Once you have positioned the laser at the desired height,

tighten the locking knob

to maintain this position.

DW074_DW079 User Manual - NA - TRANSLATED.indd 15 5/17/2018 2:05:34 PM

ENGLISH

Mounting on a Grade Rod (Fig.

)

To secure your detector to a grade rod, first attach the detector

to the clamp using the 1/4"-20 threaded knob

on the back

of the clamp. Slide the tracks

on the clamp around the rail

on the grade rod.

1. Position the detector at the height needed and turn the

clamp knob clockwise to tighten the jaws of the clamp

around the grade securing the clamp on the rod.

2. To make adjustments in height, slightly loosen the clamp,

reposition and retighten.

Construction Grade Rod (Fig.

)



DANGER: NEVER attempt to use a grade rod in a

storm or near overhanging electric wires. Death or

serious personal injury will occur.

Some laser kits include a grade rod. The

DeWALT

Grade

Rod is marked with measurement scales on both sides and

is constructed in telescoping sections. A spring-loaded button

actuates a lock to hold the grade rod at various lengths.

The front of the grade rod has the measurement scale starting

at the bottom. Use this for measuring from the ground up when

grading or leveling jobs.

The back of the grade rod is designed to measure the height

of ceilings, joists, etc. Fully extend the top section of the grade

rod until the button locks into the previous section. Extend that

section either until it locks into the adjacent section or until the

grade rod touches the ceiling or joist. The height is read where

the last extended section exits the previous lower section, as

shown in Figure

Target Card (Fig.

)

Some laser kits include a Laser Target Card to aid in locating

and marking the laser beam. The target card enhances the

visibility of the laser beam as the beam crosses over the card.

The card is marked with standard and metric scales. The laser

beam passes through the red plastic and reflects off of the

reflective tape on the reverse side. The magnet at the top of

the card is designed to hold the target card to ceiling track or

steel studs to determine plumb and level positions. For best

performance when using the Target Card, the

DeWALT

logo

should be facing you.

Laser Enhancement Glasses (Fig.

)

Some laser kits include a pair of Laser En hancement Glasses.

These glasses improve the visibility of the laser beam under

bright light conditions or over long distances when the laser is

used for interior applications. These glasses are not required to

operate the laser.



CAUTION: These glasses are not ANSI approved

safety glasses and should not be worn while operating

other tools. These glasses do not keep the laser beam

from entering your eyes.



DANGER: To reduce the risk of serious personal injury,

never stare directly into the laser beam, with or without

these glasses.

Maintenance

• Under some conditions, the glass lens may collect some

dirt or debris. This will affect beam quality and operating

range. The lens should be cleaned with a cotton swab

moistened with water.

• The flexible rubber shield can be cleaned with a wet lint-

free cloth such as a cotton cloth. USE WATER ONLY — DO

NOT use cleansers or solvents. Allow the unit to air dry

before storing.

• To maintain the accuracy of your work, check the calibration

of the laser often. Refer to Calibrating the Laser.

• Calibration checks and other maintenance repairs can be

performed by

DeWALT

service centers. Two free calibration

checks are included under the D

eWALT

One Year Free

Service Con tract.

• When the laser is not in use, store it in the kit box provided.

• Do not store your laser in the kit box if the laser is wet. Dry

exterior parts with a soft, dry cloth and allow the laser to

air dry.

• Do not store your laser at temperatures below 0˚F (-18˚C)

or above 105˚F (41˚C).



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of the

tool. These chemicals may weaken the materials used

in these parts. Use a cloth dampened only with water

and mild soap. Never let any liquid get inside the unit;

never immerse any part of the unit into a liquid. Never

use compressed air to clean the laser.

Troubleshooting

Height of Instrument Alert

The DW074LR and DW079LR/LG have a built-in alarm feature

that alerts the operator if the unit is disturbed after the unit has

self-leveled. The laser unit will stop rotating, the control panel

LED indicator light will flash, and the beeper will sound.

Turning the Laser Off

Press the the power button for 3 sec to turn the laser off. The

power LED indicator light will no longer be illuminated.

To Reset The Laser Unit for Continued Use

Turn the unit off and back on again using the power button on

the laser unit control panel.

NOTE: Always recheck the laser setup after the Height of

Instrument Alert (Hi mode) has triggered.

DW074_DW079 User Manual - NA - TRANSLATED.indd 16 5/17/2018 2:05:34 PM

ENGLISH

Service and Repairs

NOTE: Disassembling the laser level will void all warranties on

the product.

To assure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment should be performed by

authorized service centers. Service or maintenance performed

by unqualified personnel may result in a risk of injury. To locate

your nearest D

eWALT

service center call 1–800–4-

DeWALT

(1–800–433–9258) or visit our website: www.

DeWALT

.com.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help

you obtain more efficient warranty service in case there is a

problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an

insurance loss, such as fire, flood or theft, your registration

of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow

us to contact you in the unlikely event a safety notification is

required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to faulty

materials or workmanship for three years from the date of

purchase. This warranty does not cover part failure due to

normal wear or tool abuse. For further detail of warranty

coverage and warranty repair information, visit www.

DeWALT

com or call 1–800–4-

DeWALT

(1–800–433–9258). This

warranty does not apply to accessories or damage caused

where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other

rights which vary in certain states or provinces.

In addition to the warranty,

DeWALT

tools are covered by our:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts caused

by normal use, for free, any time during the first year after

purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

DeWALT

Power Tool, Laser, or Nailer for any reason, you can

return it within 90 days from the date of purchase with a receipt

for a full refund – no questions asked.

RECONDITIONED PRODUCT: Reconditioned product is

covered under the 1 Year Free Service Warranty. The 90 Day

Money Back Guarantee and the Three Year Limited Warranty

do not apply to reconditioned product.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1–800–4-

DeWALT

visit your local service center for a free replacement.

DW074_DW079 User Manual - NA - TRANSLATED.indd 17 5/17/2018 2:05:34 PM

FRANÇAIS

Définitions : Symboles et mots d'alertes de sécurité

Ce manuel d'instruction utilise les symboles et les mots d'alertes de sécurité suivants pour vous indiquer les situations dangereuses

et les risques de blessures ou de dommages.



Danger : Indique une situation dangereuse imminente qui, si elle n’est pas évitée, pourrait occasionner des blessures

graves ou mortelles.



Avertissement : Indique une situation dangereuse possible qui, si elle n’est pas évitée, pourrait occasionner des

blessures graves ou mortelles.



Mise en garde : Indique une situation dangereuse potentielle qui, si elle n'est pas évitée, pourrait occasionner des

blessures mineures ou légères.



(Utilisé sans mot) Indique un message relatif à la sécurité.

Avis : Indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait pour

l’éviter, pourrait entraîner des dommages matériels.

Si vous avez des questions ou des commentaires à propos de cet outil ou de n'importe quel outil

DeWALT

, appelez-nous

sans frais au : 1 800 4-

DeWALT

(1 800 433-9258)

Avertissement : afin de réduire le risque de blessures, l’utilisateur doit lire le mode

d’emploi.

Directives de sécurité pour lasers

MISE EN GARDE! Lire et assimiler toutes les instructions. Le non-respect des directives

indiquées ci-dessous peut entraîner des risques de choc électrique, d’incendie ou de blessures

corporelles graves.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES DIRECTIVES POUR UN USAGE ULTÉRIEUR



MISE EN GARDE! Exposition au rayonnement laser. Ne pas démonter ou modifier le laser. Aucune pièce à

l'intérieur ne peut être réparée par l’utilisateur. sous risque de lésions oculaires graves.



Avertissement : Rayonnement dangereux. L’utilisation de commandes ou de réglages ou l’exécution de procédures

autres que celles précisées dans la présente peut entraîner une exposition au rayonnement dangereux.

• Ne pas faire fonctionner le laser dans un milieu déflagrant, comme en présence de liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.

• Utiliser uniquement le laser avec les piles spécifiquement conçues à cet effet. L’utilisation de toute autre pile pourrait provoquer un

incendie.

• Ranger le laser inutilisé hors de la portée des enfants et des personnes sans expérience. Les niveaux laser sont dangereux entre les

mains d’utilisateurs inexpérimentés.

• N’utiliser que les accessoires conseillés par le fabricant pour le modèle de l'outil. Les accessoires adaptés à un laser donné peuvent être

dangereux lorsqu’ils sont utilisés avec un autre laser.

• Toute réparation de l’outil ne doit être effectuée que par des réparateurs professionnels. Toute réparation ou tout entretien réalisé par un

personnel non formé peut entraîner des blessures. Pour trouver le centre de réparation

DeWALT

le plus proche, composez le 1 800 4-

DeWALT

(1 800 433-9258) ou allez sur le site Web : http://www.

DeWALT

.com.

• Ne pas utiliser d’instruments optiques comme un télescope ou un théodolite pour observer le faisceau laser. sous risque de lésions

oculaires graves.

• Ne pas mettre le laser dans une position où une personne pourrait fixer du regard le faisceau laser, intentionnellement ou non. sous

risque de lésions oculaires graves.

• Éteindre le laser lorsqu’il n’est pas utilisé. Laisser le laser allumé augmente le risque de fixer du regard le faisceau laser.

• Ne pas positionner le laser près d’une surface réfléchissante qui pourrait renvoyer le faisceau laser dans les yeux de quelqu’un. sous

risque de lésions oculaires graves.

LASER ROTATIF

DW074LR, DW079LR, DW079LG

DW074_DW079 User Manual - NA - TRANSLATED.indd 18 5/17/2018 2:05:35 PM

FRANÇAIS

• Ne pas utiliser le laser près des enfants et ne pas laisser les enfants utiliser le laser. Il peut en résulter des blessures graves aux yeux.

• Ne pas enlever ni altérer les étiquettes d'avertissement. Enlever les étiquettes accroît le risque d’exposition au rayonnement.

• Placer le laser sur une surface stable et plane. Le laser risque d’être endommagé ou de causer des blessures graves en cas de chute.



AVERTISSEMENT : L’utilisation de commandes ou de réglages ou l’exécution de procédures autres que celles précisées

dans la présente peut entraîner une exposition au rayonnement dangereux.



MISE EN GARDE! NE PAS DÉMONTER LE LASER ROTATIF. Aucune pièce à l'intérieur ne peut être réparée par

l’utilisateur. Le démontage du laser rotatif annulera toutes les garanties du produit. Ne modifier le produit en

aucun cas. Les modifications apportées à l’outil laser pourraient entraîner une exposition à des rayonnements

laser dangereux.

• L’étiquette sur votre outil peut inclure les symboles ci-après indiqués.

V ........................volts

mW ....................milliwatts

........ symbole de mise en garde du laser

nm..........longueur d’onde en nanomètre

3R .......... Laser classe 3R

Étiquettes de mise en garde

Pour plus de commodité et de sécurité, l’étiquette suivante est apposée sur votre laser.

AVERTISSEMENT : afin de réduire le risque de blessures, l’utilisateur doit lire le mode d’emploi.

AVERTISSEMENT : RAYONNEMENT LASER. NE PAS REGARDER DIRECTEMENT LE FAISCEAU.

Produit laser de classe 3R

ÉVITER TOUTE EXPOSITION AU RAYONNEMENT LASER ÉMIS PAR CETTE OUVERTURE.

DW074_DW079 User Manual - NA - TRANSLATED.indd 19 5/17/2018 2:05:35 PM

FRANÇAIS

Renseignements sur le niveau laser

Les lasers rotatifs sans fil DW074LR et DW079LR/LG sont des

lasers de CLASSE 3R conformes aux normes 21 CFR 1040.10

et 1040.11 à l'exception des dérogations prévues par l'avis nº

50 en date du 24 juin 2007.

Conforme aux normes UL STDS 61010-1 et 2595

Certifié conforme à la norme CSA STD C22.2 nº 61010-1

Conforme à la norme CEI 60825-1:2014

Cet appareil est conforme aux exigences de la section 15

des réglementations FCC. L’utilisation est sujette aux deux

conditions suivantes : 1) Cet appareil ne doit pas causer

d’interférence nuisible; et 2) cet appareil doit accepter toute

interférence reçue, incluant une interférence pouvant causer

une opération indésirée.

REMARQUE : Cet équipement a été testé et est conforme

aux limites pour un appareil numérique de classe B selon

la section 15 du règlement FCC. Ces limites sont conçues

pour offrir une protection raisonnable contre les interférences

nuisibles dans une installation résidentielle. Cet équipement

génère, utilise et peut irradier de l’énergie radio électrique, et

s’il n’est pas installé et utilisé conformément aux instructions,

il peut causer des interférences nuisibles aux communications

radio. Toutefois, il n’y a aucune garantie selon laquelle

l’interférence ne se produira pas dans une installation

particulière. Si cet équipement cause des interférences

nuisibles à une radio ou un téléviseur, ce qui peut être

déterminé en allumant ou en éteignant l’appareil, on encourage

l’utilisateur à tenter de corriger cette interférence par l’une ou

plusieurs des mesures suivantes :

• Réorientez ou déplacez l’antenne de réception.

• Augmentez la distance entre l’équipement et le récepteur.

• Branchez le matériel dans une prise électrique située sur

un circuit différent de celui du récepteur.

• Consultez le fournisseur ou un technicien radio/télé

expérimenté pour obtenir de l’aide.

Notifications d'Industrie Canada (IC, Industry Canada),

Canada

Le circuit de cet appareil numérique de classe B est conforme à

l'ICES-003 (Canada). Cet appareil est conforme aux exigences

RSS d'Industrie Canada exempt de licence. L’utilisation est

sujette aux deux conditions suivantes : (1) cet appareil ne doit

pas causer d'interférences, et (2) cet appareil doit accepter

toutes les interférences, y compris celles qui pourraient

provoquer un fonctionnement non souhaitable de l'appareil.

LIRE TOUTES LES CONSIGNES

Piles et alimentation

Ce laser rotatif

DeWALT

accepte toutes les piles au lithium-ion

DeWALT

de 20 volts, mais est conçu pour résister au mieux aux

dommages pendant une chute lorsqu'il est utilisé avec les piles

suivantes: Toutes les piles au lithium-ion de 20 volts 1,5 A et 2

DeWALT

Charge de la pile

Le bloc-piles n’est pas totalement chargé d’usine. Vous devez

utiliser un chargeur

DeWALT

de 20 volts pour charger la pile

avant de pouvoir utiliser le laser rotatif.

• Consultez le tableau en dernière page de ce manuel pour

connaître les compatibilités entre chargeurs et blocs-piles.

• S’assurer de bien lire toutes les directives de sécurité avant

d’utiliser le chargeur.



AVERTISSEMENT :

• NE PAS tenter de charger un bloc-piles avec

des chargeurs autres que ceux décrits dans

ce manuel. Le chargeur et son bloc-piles ont

été conçus tout spécialement pour fonctionner

ensemble.

• Suivez attentivement l’ensemble des instructions

et des avertissements indiqués sur l’étiquette et

l’emballage de la pile ainsi que dans le manuel de

sécurité de la pile.

1. Pour recharger le bloc, insérez-le dans le chargeur comme

décrit dans le manuel de sécurité de la pile.

2. Attendez que la pile soit complètement chargé.

3. Faites glisser le bloc-piles hors du rail.

REMARQUE : Pour commander un bloc-piles de rechange,

s’assurer d’inclure son numéro de catalogue et sa tension.

Installation du bloc-piles 20W

DeWALT

1. Placez la pile 20 V

DeWALT

complètement chargée de

manière à ce que le bouton

(Figure 15 ) faisant face

devant vous et vers la droite.

2. Appuyez sur et maintenez enfoncé le bouton de

relâchement sur le bloc-piles.

3. Faites glisser le bloc-piles complètement dans le rail sur le

côté du laser.

4. Relâchez le bouton sur le bloc-piles.

Retirer le bloc-piles :

1. Appuyez sur et maintenez enfoncé le bouton de

relâchement du bloc-piles.

2. Faites glisser le bloc-piles hors du rail sur le laser.

3. Relâchez le bouton sur le bloc-piles.

4. Pour recharger le bloc-piles, insérez-le dans le chargeur

comme décrit dans le manuel de sécurité de la pile.



AVERTISSEMENT : Les piles peuvent exploser ou

couler et causer des blessures ou un incendie. Pour

réduire ce risque, suivez les instructions du Manuel de

sécurité de la pile.

DW074_DW079 User Manual - NA - TRANSLATED.indd 20 5/17/2018 2:05:35 PM

La page charge ...

DeWalt DW079LRK Manuel utilisateur

Marque: DeWalt

Modèle: DW079LRK

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DW079LRK User manual
español: DeWalt DW079LRK Manual de usuario
português: DeWalt DW079LRK Manual do usuário

DeWalt DW079LRK Manuel utilisateur

DeWalt DW079LRK Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents