Radiant Cooktop Workstation: Models SCR3042FB, SCR3041GB, SCR2442FB
OPERATION MANUAL
RADIANT COOKTOP WORKSTATION
MODELS: SCR3042FB, SCR3041GB, SCR2442FB
TINSEB582MRR0 E
DEC 16, 2020
CUSTOMER ASSISTANCE (US ONLY)............................... 2
CUSTOMER ASSISTANCE (CANADA ONLY) ........................ 3
US CONSUMER LIMITED WARRANTY ............................. 4
CANADA CONSUMER LIMITED WARRANTY ....................... 5
IMPORTANT SAFETY INSTRUCTIONS .............................. 6
BEFORE USING THE COOKTOP ...................................... 9
INFORMATION YOU NEED TO KNOW ABOUT THE COOKTOP .. 9
ABOUT COOKING UTENSILS .................................................... 9
COOKWARE RECOMMENDATIONS (PLACEMENT) ................ 10
RECOMMENDED COOKWARE ............................................... 10
COOKTOP FEATURES ................................................11
USING THE COOKTOP ...............................................13
CONTROL LOCK ..................................................................... 13
COOKTOP USE ........................................................................ 13
USING THE HEATERS ............................................................. 13
AUTO FEATURES .................................................................... 14
SPEED BOIL ............................................................................ 15
PRECISE LOW POWER FUNCTION ......................................... 16
SUGGESTED HEAT SETTINGS CHART .................................... 17
HOT SURFACE LIGHT INDICATOR ......................................... 17
AUTOMATIC TURN OFF .......................................................... 17
TIMERS .................................................................................. 17
SPECIFICATION ......................................................20
CLEANING AND CARE ...............................................21
BEFORE YOU CALL FOR SERVICE .................................22
CUSTOMER ASSISTANCE UNITED STATES ONLY
REGISTER YOUR PRODUCT
Registering your new product is easy and offers benets that help you get the most
out of your Sharp product including:
9 Convenience: Ifyoueverneedwarrantysupport,yourproductinformationisalreadyonle.
9 Communication:StayuptodatewithimportantnoticationsandspecialoffersfromSHARP.
9 Support: Quickly access support content including Owner’s Manuals, FAQ’s,
How-toVideos,andmuchmore.
3 EASY WAYS TO REGISTER TODAY!
PRODUCT SUPPORT
If you have questions about the setup or operation of your product, please refer to
the corresponding section within this manual.
Additionally, visit www.sharpusa.com/support to access exclusive content about your
product including:
Æ FAQ’s and How-To Videos
Æ Find or Request Service
Æ Purchase an Extended Warranty
Æ Downloads including the Installation Guide, Spec Sheet, and Owner’s Manual
CONTACT US
If at any time you have questions or comments concerning your SHARP product,
please contact the SHARP Customer Assistance Center. We are available to
assist you through multiple contact methods for your convenience:
Scan this QR Code on your mobile device Visit http://www.sharpusa.com/register
ONLINE
Visit our sites to
learn more about
your product at
sharpusa.com and
sbl.sharpusa.com
See the Contact Us section on our sites U.S. | www.sharpusa.com/support Contact a Sharp Advisor on the phone
Contact a Sharp Advisor on the phone
CALL US
US 800-BE-SHARP
800-237-4277
Mon-Fri: 7am-7pm CST
Sat-Sun: 9am-7pm CST
CALL US
US 800-BE-SHARP
800-237-4277
Mon-Fri: 7am-7pm CST
Sat-Sun: 9am-7pm CST
EMAIL
Available 24/7
US: sharpusa.com
CHAT ONLINE
Mon-Fri: 7am-7pm CST
Sat-Sun: 9am-7pm CST
SCAN
Use the camera or
QR code scanning
application on your
mobile device
2E
E
2E
CUSTOMER ASSISTANCE (US ONLY)
CUSTOMER ASSISTANCE CANADA ONLY
To aid in answering questions if you call for service or for reporting loss or theft,
please use the space below to record the model and serial number located on the
back side of the unit.
Model Number:
Serial Number:
Date of Purchase:
Dealer Name:
Address:
City:
Province:
Postal Code:
Telephone:
PRODUCT SUPPORT
If you have questions about the setup or operation of your product, please refer to
the corresponding section within this manual.
Additionally, visit http://sharp.ca/support-home.aspx to access exclusive content
about your product including:
Æ Find a Dealer
Æ Find Service Locations
Æ Downloads including the Installation Guide, Spec Sheet, and Owner’s Manual
CONTACT US
If at any time you have questions or comments concerning your SHARP product,
please contact the SHARP Customer Assistance Center. We are available to
assist you through multiple contact methods for your convenience:
http://sharp.ca/contact-emailus.aspx CA | sharp.ca/support-home.aspx Contact a Sharp Advisor on the phone
CALL US
CA 877-278-6709
Mon-Fri: 7am-7pm CST
EMAIL
Available 24/7
See the Contact Us
section on our site.
SUPPORT SITE
Product Downloads,
Service Locater, Where
to Buy, Toner Recycling
Program and more.
E3
E
CUSTOMER ASSISTANCE (CANADA ONLY)
US CONSUMER LIMITED WARRANTY
4E
E
SHARP ELECTRONICS CORPORATION ("Sharp") warrants to the rst consumer purchaser ("Purchaser") that this SHARP brand
product ("Product"), when shipped in its original container and sold or distributed in the United States by Sharp or an authorized
Sharp dealer or reseller, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair
the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the Purchaser for
parts or labor for the period(s) set forth below.
This limited warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to misuse, abnormal service or
handling, or which has been altered or modied in design or construction.
In order to enforce the rights under this limited warranty, the Purchaser should follow the steps set forth below and provide proof of
purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to Purchasers by law. ALL
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein,
or to extend the duration of any warranties beyond the time period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive
remedy available to the Purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute
complete fulllment of all liabilities and responsibilities of Sharp to the Purchaser with respect to the Product, and shall constitute
full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable,
or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed
by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incident or consequential
economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion
may not apply to you.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
PUERTO RICO.
Your product model number &
description
Model # SCR3042FB, SCR3041GB, or SCR2442FB
(Be sure to have the model number and serial number found afxed on the bottom of your
product available when you need service for your Product)
Warranty period for this product: One (1) year parts and labor including in-home service.
Product must be accessible to provide service.
Additional item(s) excluded from
warranty coverage (if any):
Non-functional accessories, service calls to your home to instruct how to use your radiant
cooktop appliance, replace or repair house fuses or to correct house wiring, improper com-
mercial use, installation, or maintenance, damage to the product caused by lack or improper
cleaning, delivery, accident, modications, re, oods or acts of God.
Where to obtain service: From a Sharp Authorized Servicer located in the United States. To nd the location of the
nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-237-4277 (1-800-BE-SHARP).
What to do to obtain service: In-home service is provided for one year from date of purchase. In-home service can be arranged
by calling 1-800-BE-SHARP. Be sure to have Proof of Purchase available.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP or visit www.sharpusa.com.
SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR OVEN EVER REQUIRE WARRANTY SERVICE.
CANADA CONSUMER LIMITED WARRANTY
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (“Sharp”) warrants to the rst purchaser for this Sharp brand product (“Product”), when shipped
in its original container and sold or distributed in Canada by Sharp or by an authorized Sharp dealer, and Product was not sold “as
is” or “sales nal” that the Product will during the applicable warranty period, be free from defects in material and workmanship,
and will within the applicable warranty period, either repair the defective Product or provide the rst purchaser a replacement of the
defective Product.
This warranty does not apply to any appearance items of the product nor to the additional excluded item(s) set forth below nor to any
product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal
service or handling, which has been altered or modied in design or construction, or if the serial number or model number afxed to
Product has been removed, defaced, changed, altered or tampered with.
How to get service: Should this Sharp product fail to operate during the warranty period, warranty service is provided by an Authorized
Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service will be carried out to locations accessible
by on-road service vehicle and within 50 km of an authorized Sharp service centre. The servicer may if necessary take the unit for
repair at the servicer's facility. No other person (including any Sharp dealer or service centre) is authorized to extend, enlarge or
transfer this warranty on behalf of Sharp.
The express warranties in this limited warranty are, except for consumer purchasers domiciled in Quebec, in lieu of and, except to the
extent prohibited by applicable law, Sharp disclaims all other warranties and conditions, express or implied, whether arising by law,
statute, by course of dealing or usage of trade, including, without limitation, implied warranties or conditions of merchantability and/or
quality, tness for a particular use or purpose, and/or non-infringement. Limitations (not applicable to consumer purchasers domiciled
in Quebec to the extent prohibited under Quebec law): (a) Sharp shall not be liable for any incidental, special, consequential, economic,
exemplary or indirect damages of any kind or nature (including lost prots or damages for loss of time or loss of use or loss of data)
arising from or in any connection with the use or performance of a Product or a failure of a Product, even if Sharp is aware of or has
been advised of the possibility of such damages; (b) the remedies described in this limited warranty constitute complete fulllment
of all obligations and responsibilities of Sharp to the purchaser with respect to the Product and shall constitute full satisfaction of all
claims, whether based on contract, negligence, strict liability or otherwise. Some provinces may not allow the exclusion or limitation
of certain damages, or limits on the duration or voiding of implied warranties or conditions; in such provinces, the exclusions and
limits herein may not apply. This limited warranty is, except for consumer purchasers domiciled in Quebec, governed by the laws of
the Province in Canada in which the purchaser has purchased the Product. For consumer purchasers domiciled in Quebec this limited
warranty is governed by the laws of Quebec.
Your product model number &
description
Model # SCR3042FB, SCR3041GB, or SCR2442FB
(Be sure to have the model number and serial number found afxed on the bottom of your
product available when you need service for your Product)
Warranty period for this product: One (1) year parts and labor including in-home service.
Product must be accessible to provide service.
Additional item(s) excluded from
warranty coverage (if any):
Non-functional accessories, service calls to your home to instruct how to use your radiant
cooktop appliance, replace or repair house fuses or to correct house wiring, improper commercial
use, installation, or maintenance, damage to the product caused by lack or improper cleaning,
delivery, accident, modications, re, oods or acts of God.
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD
335 Britannia Road East
Mississauga, Ontario
L4Z 1W9
(905) 568-7140
Website: www.sharp.ca
SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR OVEN EVER REQUIRE WARRANTY SERVICE.
THIS LIMITED WARRANTY IS VALID ONLY IN CANADA
E5
E
6E
E
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT
Keep these instructions handy for future use.
The appliance is manufactured in compliance with the relevant
safety standard.
WARNING
Read all instructions carefully before installation
and operation.
WARNING
Failure to follow these warnings could result in
a re or explosion that causes property damage, personal injury
or death. To reduce the risk of re, electric shock or injury, take
the following precautions:
INTENDED USE
• This appliance is designed for built-in household use only.
• Do not use outdoors.
• Do not use the appliance to heat a room.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions
should be followed, including the following:
1 Use this appliance only for its intended purpose as described
in this manual.
2 Proper Installation - Be sure your appliance is properly
installed and grounded by a qualied technician in accor-
dance with the provided installation instructions.
3 Never Leave Surface Units Unattended at High Heat Set-
tings - Boilovers cause smoking and greasy spillovers that
may catch on re. Do not allow pots and pans to boil dry
or empty.
4 Never use your appliance for warming or heating the room.
5 Do Not Leave Children Alone - Children should not be
left alone or unattended in area where appliance is in use.
They should never be allowed to sit or stand on any part
of the appliance.
6 Wear Proper Apparel - Loose tting or hanging garments
should never be worn while using the appliance. Be careful
when reaching for items stored over the cooktop. Flammable
material could be ignited if brought in contact with hot
surfaces of heaters and may cause severe burns.
7 User Servicing - Do not repair or replace any part of appli-
ance unless specically recommended in this manual. All
other servicing should be referred to a qualied technician.
8 Do Not Use Water on Grease Fires - Smother a ame or use
a dry chemical or foam-type extinguisher. Flaming grease
outside a pan can be put out by covering it with baking
soda or, if available, by a multi-purpose dry chemical or
foam-type re extinguisher.
9 Use Only Dry Potholders - Moist or damp potholder on
hot surfaces may result in burns from steam. Do not let
potholders touch hot surfaces or radiant heaters. Do not use
a towel or other bulky cloth.
10
CAUTION
Storage in or on Appliance - Flammable
materials should not be stored in an oven or near surface
units. Do not store items of interest to children in cabinets
above a cooktop. Children climbing on the cooktop to reach
items could be seriously injured.
11 Do not place hot cookware on top of the controls. The heat
can transfer to the surface, resulting in the keypad controls
becoming hot.
12 DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
UNITS. Surface units may be hot even though they are dark
in color. These surfaces may become hot enough to cause
burns. During and after use, do not touch or let clothing or
other ammable materials contact heaters until they have
had sufcient time to cool. Other potentially hot surfaces
include cooktop and areas facing the cooktop.
13 The installer should provide location of circuit breaker or
fuse for the cooktop.
14 Before performing any service, disconnect the cooktop
power supply at the household distribution panel by remov-
ing the fuse or switching off the circuit breaker.
15 Do not climb, stand or hang on cooktop. This could cause
severe personal injury or damage the cooktop.
16 Teach children not to play with the controls or any other
part of the cooktop.
17 Always keep wooden and plastic utensils and canned food
a safe distance from your cooktop.
18 Always keep combustible wall coverings, curtains or drapes
a safe distance from your cooktop.
19 Never heat a sealed food storage container on cooktop as
pressure buildup from increasing temperature could cause
the container to rupture.
20 Do not repair or replace any part of the appliance. If the
cooktop display, heaters or touch controls fail, consult a
SHARP AUTHORIZED SERVICER.
IMPORTANT ENVIRONMENT OF UNIT
1 To reduce the risk of re, do not store anything directly
on top of the appliance surface when the appliance is in
operation.
2 Always have a working smoke detector in or near the
kitchen.
3
IMPORTANT
Do not leave lids other metal objects such
as knives, forks or spoons on the cooktop. If the cooktop
is turned on, these objects can heat up quickly and may
cause burns.
4 Do not place rough or uneven objects on the units as they
may damage the surface. If the cooktop is near a window,
ensure that curtains do not blow over or near the unit.
5 Do not store hard or pointed objects over the cooktop as
they can damage the unit if they fall on top.
6 Do not put detergents or ammable materials in the equip-
ment installed under the cooktop.
7 Extreme caution must be used when moving an appliance
containing hot oil or other hot liquids.
8 While cooking, any overowed fat or oil on the cooktop may
ignite. There is a risk of burning and re; therefore, control
the cooking process at all times. The use of accessory attach-
ments not recommended by the appliance manufacturer may
cause injuries. Items with a magnetic eld such as: radios,
E
E7
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
televisions, credit cards, cassette tapes etc., can affect the
unit. The marked electrical rating should be at least as great
as the electrical rating on the appliance.
9 To prevent accidents and achieve optimal ventilation, allow
for sufcient space around the cooking area.
10 Use Proper Cookware Size - This appliance is equipped with
four heating elements, (two 7” heaters on the left that may
be used individually or combined as a Bridge for 9”x18”
griddles; one 6” heater; and one that may be used as a 6”
or 9” Double heater). Choose cookware with a at bottom
large enough to cover the surface of the heater. The use of
undersized cookware will expose a portion of the heating
surface where direct contact may be made and cause serious
injury. Compatible cookware will improve efciency.
11 To reduce risk of burns, ignition of ammable materials,
and spillage due to unintentional contact with cookware, the
cookware handles should be turned inward and not extend
over adjacent heating surfaces.
12 Wear Proper Apparel - Loose tting or hanging garments
should never be worn while using the appliance.
RADIANT SURFACE HEATERS
1 Use Proper Pan Size - This appliance has different size
heaters. Select utensils having at bottoms large enough
to cover the surface of the heater. The use of undersized
utensils will expose a portion of the heater to direct contact
and may result in ignition of clothing. Proper relationship of
utensils to the size of the heater will also improve efciency.
2 Never Leave Surface Units Unattended at High Heat Set-
tings - Boilovers cause smoking and greasy spillovers that
may catch on re. Do not allow pots and pans to boil dry
or empty.
3 Glazed Cooking Utensils - Only certain types of glass, glass/
ceramic, ceramic, earthenware or other glazed utensils are
suitable for cooktop service without breaking due to the
sudden change in temperature.
4 Utensil Handles Should Be Turned Inward and Not
Extended Over Adjacent Surface Units - To reduce the risk
of burns, ignition of ammable materials and spillage due
to unintentional contact with utensils, the handle of a utensil
should be positioned so that it is turned inward and does not
extend over adjacent heaters.
5 Do Not Cook on Broken Cooktop - If cooktop should
break, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock. Contact
a qualied technician immediately.
6 Clean Cooktop with Caution - If a wet sponge or cloth is
used to wipe spills on a hot surface of a heater, be careful
to avoid steam burn. Some cleaners can produce noxious
fumes if applied to a hot surface. Please see cleaning the
glass cooktop section.
7 Clean ventilating hoods frequently. Grease should not be
allowed to accumulate on hood or lter.
8 When aming foods under the hood, turn the fan on.
9 Deep Fat Fryers - Use extreme caution when moving the
grease kettle or disposing of hot grease.
10 Always turn the heaters off before removing cookware.
11 Carefully monitor foods being fried at high or medium
high heat settings.
12 Food for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan.
13 Use little fat for effective shallow or deep fat frying. Filling
the pan too full of fat can cause spillovers when food is
added.
If a combination of oils or fats will be used in frying, stir
together slowly before heating or as fats melt.
14 Always heat fat slowly and monitor as it heats.
15 Use a deep fat thermometer whenever possible to prevent
heating fat beyond the smoking point.
16 Avoid scratching the glass cooktop. The cooktop can be
scratched with items such as sharp instruments, rings or
other jewelry and rivets on clothing.
17 Large scratches or impacts to glass cooktop can lead to
broken or shattered glass.
18 Never use the glass cooktop surface as cutting board as this
will damage the appliance.
19 Do not place or store items that can melt or catch re on the
glass cooktop, even when it is not being used.
20 Be careful when placing spoons or other stirring utensils on
glass cooktop surface when it is in use. They may become
hot and could cause burns. The Spoon Rest Holder provided
with your Workstation Sidekicks is ideal for resting utensils
while cooking.
21 Do not allow objects or cookware that can melt, aluminum
foil, paper or cloth to come in contact with a heater. Avoid
preparing food in aluminum foil or plastic containers over
the heaters. Do not line heaters with aluminum foil.
8E
E
IMPORTANT SAFETY INSTRUCTIONS
UNPACKING AND EXAMINING YOUR
COOKTOP
CONDITION OF UNIT
WARNING
Do not operate any appliance with a damaged
cord or after the appliance malfunctions or has been damaged in
any manner. Return appliance to the nearest authorized service
facility for examination, repair, or adjustment.
IMPORTANT Do not cook on broken cooktop. If cooktop
breaks, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock.
SERVICE AND REPAIR SAFETY
WARNING
Do not repair or replace any part of the appliance. If the cook-
top display, heaters or touch controls fail, consult a SHARP
AUTHORIZED SERVICER.
READ AND SAVE THESE INSTRUCTIONS
PRODUCT DISPOSAL
This product may not be treated as household waste. Instead it
should be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about
recycling of this product, please contact your local city ofce,
your household waste disposal service or the shop where you
purchased the product.
E9
E
BEFORE USING THE COOKTOP
Before operating your new Radiant cooktop Workstation:
• Ensure your cooktop has been properly installed and the
power supply is properly connected by following all instruc-
tions in the Installation Manual included with your cooktop.
• Be sure all protective packaging materials and tape have been
correctly and completely removed.
• Read and understand all instructions in this Operation
Manual.
INFORMATION YOU NEED TO KNOW
ABOUT THE COOKTOP
• GLASS CERAMIC COOKTOP - Make sure the surface
and the pan bottom are clean before turning on. Do not use
the cooktop if the glass is broken or if metal melts on it.
• RADIANT HEATERS - The radiant heaters are beneath the
smooth glass ceramic cooktop. The design on the cooktop
outlines the area of the heater unit underneath. When the
cooktop is in use, the Hot Surface/ON Indicator Light next
to the heater being used illuminates, even if the cooktop unit
does not look red. The areas surrounding around the heaters
may become hot enough to cause burns.
• HOT SURFACE INDICATOR - The Hot Surface/ON
Indicator light illuminates when a heater is turned ON and
remains on after the heater has been turned OFF to indicate
hot surface temperature. The indicator light will turn OFF
automatically after the residual heat has cooled.
•
WARNING
In the event of a power failure to the home or
to the cooktop, be aware that SURFACES OF HEATERS
WILL REMAIN HOT even though the Hot Surface/ON
Indicator Lights ARE NO LONGER ILLUMINATED.
The Hot Surface/ON Indicator Lights will NOT come on
automatically once power has been restored.
• TEMPERATURE LIMITER - The radiant heaters have a
temperature limiter that allows the unit to cycle on and off,
even at the HI setting. It protects the glass ceramic cooktop
from damage. Cycling at the HI setting can occur when
improper cookware is used.
NOTE:
• Never leave any items on the cooktop. Hot surfaces of heat-
ers may ignite ammable items, melt or soften plastics or
increase pressure in closed containers causing them to burst.
• Don’t store heavy items above the cooktop as they can cause
damage if they drop onto the cooktop.
• Never cook food directly on the cooktop. Always use
cookware.
• Never touch hot cookware or pots and pans directly with
your hands. ALWAYS use oven mitts or potholders when
handling hot cookware or pans to protect hands and arms
from burns.
ABOUT COOKING UTENSILS
For best results and energy conservation, choose cooking utensils
as described below. Improper use of cookware can cause damage
to the surface of the cooktop not covered under warranty.
• BOTTOM OF PAN - Pans should have at bottoms that
make good contact with the entire surface of the heater.
Check for atness by using a straight edge. Pans with curved
or warped bottoms are not recommended.
• SIZE OF PAN - Pan size should match the amount of food
and the size of the heater. Do not use canners or pans that
exceed the width of the radiant heaters.
• MATERIAL OF PAN - Always use a utensil for its intended
purpose. Follow manufacturer’s instructions. Some utensils
were not made to be used on the cooktop.
• POSITION OF PAN - Always place the pan in the center
of the heater you are using.
• WOK COOKING - Only a at-bottomed wok is recom-
mended. Do not use round-bottom wok or a wok with a
support ring.
Improper use of cookwares can cause damage to the surface of
the cooktop that is not covered under warranty.
• Do not slide cookware across the cooktop surface because
it can scratch the glass or may leave marks which need to be
removed promptly.
• Never allow a pan to boil dry. This could damage the pan
and the cooktop.
• Do not use aluminum foil on the cooktop surface.
• Do not use cooktop as a cutting board.
The quality and type of cookware material used affects how
rapidly and evenly heat is distributed. This will affect the
cooking results.
• Cookware with heavier bottoms distribute heat effectively
delivering consistent cooking results.
• Dirt and grease buildup on the bottom of pots and pans affects
heating; always use cookware that can be easily cleaned after
each use.
Always follow manufacturer’s recommended guidelines for use
with cookware.
10E
E
BEFORE USING THE COOKTOP
COOKWARE RECOMMENDATIONS
(PLACEMENT)
For best results and energy conservation, choose cookware that
correctly ts the size of the heater being used. When using a
griddle for the Bridge feature, the size recommended is 9"x18".
Be sure to follow the following recommendations for using
cookware:
INCORRECT
• Cookware not centered on heater surface.
• Curved or warped pan bottoms or sides.
• Pan does not meet the minimum size required for the heater
used.
NOTE: Use of undersized cookware exposes a portion of the
hot surface to contact with skin or clothing when cooking.
• Pan bottom rests on cooktop trim or does not rest completely
on the cooktop surface.
• Heavy handle tilts pan.
CORRECT
• Cookware centered correctly on heater surface.
• Flat pan bottom & straight sides.
• Pan rests completely on the cooktop surface.
• Pan is properly balanced.
• Do not let cookware extend
1
/2" (13 mm) beyond the surface
of the heater.
RECOMMENDED COOKWARE
Aluminum • Conducts heat quickly and evenly.
• Use medium to heavy weight.
• Works for most cooking.
Stainless Steel • Heats quickly but with uneven heat
distribution.
• Recommended to use with a core or
base of aluminum or copper on the
steel to improve distribution of heat.
Copper • Conducts heat quickly and evenly.
Cast Iron with
painted on enamel
• Use cast iron if bottom of the pan is
coated with enamel.
• Conducts heat slowly and evenly.
• Ideal for frying and browning of
dishes.
Glass/Ceramic or
Ceramic
• Heats slowly but with uneven heat
distribution.
• Best results when cooking dishes on
low or medium heat settings.
• Follow manufacturer’s recommenda-
tions.
Porcelain enamel
painted on cast
iron or steel
• Refer to recommendations for cast
iron or stainless steel.
E11
E
COOKTOP FEATURES
9 Left Rear Heater
10 Left Front Heater
11 Right Rear Heater
12 Right Front Heater
13 Power Level Digital Display
14 Power Curve Display
15 Hot Surface/ON - Red Indicater Light
16 Power Slider Bar
17 Auto Features
18 Power ON/OFF Keypad
19 Control Lock
20 Control Lock ON - Red Indicator Light
21 Precise Low Power Curve Display
22 Timer Digital Display
23 Timer ON - Red Indicator Light
24 Timer +/- Keypads
25 Bridge - Red Indicator Light
26 Double Heater/ON - Red Indicator Lights
1 7" dia. 1500W Radiant (bridge)
2 7" dia. 1500W Radiant (bridge)
3 6" dia. 1200W Radiant
4 9"/6" dia. 3000 W Radiant
5 Glass Touch Control
WORKSTATION SIDEKICKS
6 6"x21" Spoon Rest Holder
7 Two Removable spoon Rest Pans
(Not included with all models)
8 8"x21" Cooling Surface (Not included with all models)
1
2 5
3 4
7
6
8
1
2 5
3
4
7
6
8
9
10
13
15
23
25
24
19
20
13
23 2313
25 1421 1515
11
12
13
15
23
18
16
26
1722 23
MODELS: SCR3042FB, SCR3041GB MODEL: SCR2442FB
12E
E
COOKTOP FEATURES
30" RADIANT COOKTOP WORKSTATION SIDEKICKS
(NOT INCLUDED WITH ALL MODELS)
Your cooktop is also a workstation with the inclusion of our kitchen grade stainless-steel Cooling Surface (8"x21") and Spoon Rest
(6"x21") with two drip trays. The Sidekicks can attach magnetically on either edge of the cooktop to secure in place; or be attached
magnetically to each other on a single side of the cooktop; or set on the adjacent counter (the rubber feet protect countertop surfaces).
The Cooling Surface provides a location to set hot cookware after removing from the cooktop or the oven.
The Spoon Rest lets you rest cooking utensils while protecting your countertop from stains and drips. The Rest includes two removal
drip trays for easy cleaning after food preparation. All items are dishwasher-safe (upper or lower rack).
EASY ATTACHMENT
ARRANGE SOLO
SPOON REST
COOLING SURFACE
ARRANGE AS YOU LIKE
E13
E
USING THE HEATERS
TURN ON HEATERS
Select desired heater and touch ON
keypad. A tone will sound, and the Hot
Surface/ON Indicator Light will blink.
NOTE: Heater selection will complete
10 seconds after the last keypad is touched (ON, Power Slider
Bar, Bridge, Double, Speed Boil or Precise Low).
POWER LEVEL SELECTION
Select desired power level by
sliding nger across the Power
Slider Bar, moving toward the right to increase power level.
The selected power level will be shown in the Power Level
Digital Display of the heater and in the Power Curve display in
the center of the cooktop display. The lights on the Power Curve
display illuminate 2 segments at a time as the power level is
selected. (See section PRECISE LOW POWER for information
on specic temperature control for delicate foods.)
Lowest Power Level Setting - 1
Highest Power Level Setting - 9
A power level between 1 and 9 must be selected regardless of any
other keypad pressed (e.g., the BRIDGE or TIMER +/- keypads).
If no power level is selected, the heater will automatically turn
OFF in 10 seconds.
NOTE:
• If two or more nger touches are detected, the selector will
default to the highest power setting.
• If the Control Lock is activated, the Power Slider Bar will
be locked.
POWER LEVEL ACCEPTANCE
After power level is selected, a tone will sound, the Hot Surface/
ON Indicator Light will stop blinking and remain on. Touch the
heater ON keypad again to accept the level and begin cooking,
or select Bridge, Double, Speed Boil or Precise Low (see Auto
Features section for details on these functions).
If no other keypad is touched within 10 seconds, the power level
will be accepted automatically. If another heater is selected, the
power level will be accepted on the current heater automatically.
USING THE COOKTOP
CONTROL LOCK
The Control Lock function prevents
unwanted operation, such as by small
children. The Control Lock Indicator
Light above the Control Lock keypad
indicates it is locked. When Control
Lock is deactivated, the indicator light
will turn off.
FIRST TIME USE OR POWER RESTORATION
When the cooktop is powered ON for the rst time, or after
power is restored in the event of a power outage, Control Lock
will activate and the control panel will be locked.
Control lock must be deactivated to access the power ON/OFF
keypad and operate the cooktop.
Select the desired heating element by pressing the ON keypad,
then move the power level to 0 on the Power Curve selector.
CONTROL LOCK MAY BE ACTIVATED IN THE
FOLLOWING 2 CASES
1 When the cooktop main power is OFF.
If Control Lock is turned ON when the cooktop is OFF, all
keypads are locked, including main Power ON/OFF. Control
Lock must be deactivated to use the cooktop heaters.
2 When the cooktop is in use and one or more heaters is
active.
When Control Lock is turned ON during cooking, all func-
tions are locked EXCEPT: individual Heater OFF keypads,
cooktop power ON/OFF keypad and the Control Lock
keypad.
TO LOCK
Touch and hold Control Lock keypad for 3 seconds, a tone will
sound, and the Control Lock Indicator Light above the Control
Lock keypad will illuminate.
TO UNLOCK
Touch and hold Control Lock keypad for 3 seconds, a tone will
sound, the Control Lock Indicator Light will turn OFF. The
cooktop is in Standby mode.
COOKTOP USE
TURN ON THE COOKTOP
The cooktop is switched ON by touching the
ON/OFF keypad for 1 second. A tone will
sound, and all heater digital displays will
show “0”.
TO TURN OFF THE COOKTOP
The cooktop is switched OFF by touching the ON/OFF keypad
for 1 second. A tone will sound, and all heater digital displays
will be turned OFF.
NOTE: If a heater is not selected within 10 seconds, the cooktop
will turn OFF automatically.
CONTROL
LOCK - ON
CONTROL
LOCK - OFF
14E
E
The Power Curve Display will show the selected power level
for 10 seconds or until a new heater unit is turned on. The
power level of the last heater set will remain illuminated for 10
seconds before turning off while cooking. The heater will display
the numeric value of the power level on its digital display until
the unit is turned off.
A small red decimal light will illuminate
at the bottom right corner of the Power
level Digital Display indicating that this
heater has accepted the power level. It
will remain illuminated for 10 seconds,
or until another heater or the independent timer is selected.
ADJUST POWER LEVEL
Power level can be adjusted at any time
during cooking.
Simply select the desired heater by
pressing the ON keypad and follow the
instructions for Power Level Selection
and Power Level Acceptance.
NOTE: Be sure to select the appropriate heater before adjusting
cooking temperature.
TURN OFF HEATER
Select the desired heater and
touch OFF, “0” will display for
power level.
OR
Select the desired heater by
touching the ON keypad, then
move the power level to 0 on
the Power Slider Bar. After 10
seconds, a tone will sound, and
the heater will turn OFF. The
Hot Surface/ON Indicator Light
may still be illuminated until
the heater cools.
AUTO FEATURES
The Radiant cooktop has 4 Auto Feature selections:
• Bridge
• Double Heater
• Speed Boil
• Precise Low Power
These provide convenient and exible cooking preset options
to accommodate different sizes of cookware and temperature
control.
USING THE COOKTOP
BRIDGE HEATER
The left front and rear heaters can be synced together to
accommodate larger sized cookware. For example, a 9"x18"
griddle specically designed for use with glass cooktops is
recommended.
TURN BRIDGE ON
1 Select either of the two heaters and turn ON as instructed in
the section: TURN ON HEATERS.
2 Touch the BRIDGE keypad to sync the two heaters together;
a tone will sound and the Hot Surface/ON Indicator Lights
for both heaters will begin to blink indicating the BRIDGE
preset has been enabled.
3 Set power level and accept power level as instructed in
the sections POWER LEVEL SELECTION and POWER
LEVEL ACCEPTANCE.
BRIDGE may be touched before or after selecting the power
level, but it must be touched before touching the heater ON
keypad again for the power level to be accepted or before 10
seconds pass and the power level is automatically selected
if no other keypads are touched.
4 To adjust power level, select one of the heaters by pressing the
heater ON keypad and follow the instructions in the section
ADJUST POWER LEVEL.
E15
E
USING THE COOKTOP
TURN BRIDGE OFF
Bridge may be turned OFF by the following methods described
in the section TURN OFF HEATERS:
1 Select and touch one of the two heater OFF keypads.
OR
2 Select one of the two heaters by touching the ON keypad,
then move the power level to 0 on the Power Slider Bar. After
10 seconds, a tone will sound, and the heater will turn OFF.
The Hot Surface/ON Indicator Light may still be illuminated
until the heaters cool.
DOUBLE HEATER
The right front heater has DOUBLE HEATER capability to
provide for larger size pots and pans and large quantities of food.
Single size - 6" diameter
Double size - 9" diameter.
The heater’s default setting is to use the single size.
• To use SINGLE HEATER, follow the instructions for turn-
ing on, selecting, and accepting power levels in the sections
TURN ON HEATERS, POWER LEVEL SELECTION and
POWER LEVEL ACCEPTANCE.
This will turn on the smaller, inner heater.
TURN DOUBLE HEATER ON:
To use as a double size:
1 Touch the DOUBLE keypad before accepting the power level
set by the Power Slider Bar.
DOUBLE may be touched before or after selecting the power
level, but it must be touched before touching the ON keypad
again for the power level to be accepted or before 10 seconds
pass and the power level is automatically selected if no other
keypads are touched.
The DOUBLE HEATER Indicator Light will illuminate
indicating the larger size and power level selection have been
accepted.
2 Power level may be adjusted by following the same instruc-
tions in the section ADJUST POWER LEVEL.
TURN DOUBLE HEATER OFF
DOUBLE HEATER may be turned OFF by the following
methods described in the section TURN OFF HEATERS:
1 Select and touch the heater OFF keypad.
OR
2 Select the heater by touching the ON keypad, then move the
power level to 0 on the Power Slider Bar. After 10 seconds,
a tone will sound, and the heater will turn OFF. The Hot
Surface/ON Indicator Light may still be illuminated until
the heater cools.
TURN DOUBLE HEATER OFF, KEEP SINGLE HEATER
DOUBLE HEATER can be turned OFF allowing the heater to
switch to the default single heater size during cooking.
For example, if you want to continue cooking using only the
smaller, inner heater:
1 Select and touch the heater ON keypad.
2 Touch DOUBLE keypad, a tone will sound.
3 Touch the heater ON keypad again to accept the same power
level or use Power Slider Bar to adjust power level if desired,
then touch ON keypad.
CAUTION
The surface of the larger diameter heater will be
hot, use caution if removing or adding pots and pans of different
sizes when switching the heater size.
NOTE:
• Cooking results are best with pots and pans suited to the
appropriate heater size.
• The single heater can be switched to double heater function
using the same steps (1-3) listed above. Use appropriate pot
and pan size if modifying heater size.
SPEED BOIL
The SPEED BOIL function is used to cook at a maximum
boosted power level for 10 minutes. This convenient function
allows a two-stage process in which a desired power level can be
set for regular cooking and the heater will automatically return
to that power level after maximum boost time (10 minutes) has
completed.
WARNING
SPEED BOIL is only recommended for boiling
water. NEVER leave a pot or pan unattended when using the
SPEED BOIL function.
SPEED BOIL can be used with single or multiple heaters, bridge
or double heater cooking functions.
When using SPEED BOIL, the power level will alternately ash
“P” with the number of the power level selected (1-9) for the
selected heater in the Heater Digital Display.
TURN SPEED BOIL ON
Follow the instructions for turning on single heater, selecting and
accepting power levels in the sections TURN ON HEATERS,
POWER LEVEL SELECTION and POWER LEVEL
ACCEPTANCE.
SPEED BOIL may be touched before or after selecting the
power level, BRIDGE or DOUBLE HEATER if using with
those functions, but it must be touched before touching the ON
keypad again for the power level to be accepted or before 10
seconds pass and the power level is automatically selected if no
other keypads are touched.
TURN SPEED BOIL AND HEATER OFF
SPEED BOIL may be turned OFF by the following methods
described in the section TURN OFF HEATERS:
1 Select and touch the heater OFF keypad.
OR
16E
E
USING THE COOKTOP
2 Select the heater by touching the ON keypad, then move the
power level to 0 on the Power Slider Bar. After 10 seconds,
a tone will sound, and the heater will turn OFF. The Hot
Surface/ON Indicator Light may still be illuminated until
the heater cools.
Either of the two methods described above will turn the heater
OF F.
TURN ONLY SPEED BOIL OFF, KEEP HEATER ON:
SPEED BOIL can be turned OFF allowing the heater to switch
to regular power level scale without boost. For example, if you
want to cancel Speed Boil but continue cooking with regular
power level 5.
1 Select and touch the heater ON keypad.
2 Touch SPEED BOIL keypad, a tone will sound.
3 Touch the heater ON keypad again to accept the regular
power level 5 (or use the Power Slider Bar to adjust level
rst if desired).
4 The letter “P” will cease ashing on the Heater Digital
Display, only the number 5 will be displayed indicating
regular power level scale.
PRECISE LOW POWER FUNCTION
PRECISE LOW POWER has 3 settings
• Melt
• Warm
• Simmer
The cooktop regulates power levels with precision to maintain
temperature for delicate food items.
MELT
Melt works well for items with low burn points such as chocolate
and butter.
WARM
Warm allows food to stay warm without scorching or drying.
SIMMER
Simmer allows dishes to cook over longer periods at steady low
temperatures.
PRECISE LOW POWER can be used
with single or multiple heaters, bridge
or double heater cooking functions.
When setting the power level, the
Power Curve display will illuminate
1 segment at a time instead of 2 as in
the regular default power level setting.
This indicates that the temperature
control is adjusted for maintaining
the reduced power scale.
NOTE : When using PRECISE LOW POWER, the power
level will alternately ash “L” with the number of the selected
power level (reduced low level 1-9) for the selected heater.
PRECISE LOW POWER SCALE
1-3 Melt
4-6 Warm
7-9 Simmer
TURN PRECISE LOW POWER ON
Follow the instructions for turning on single heater, setting
and accepting power levels in the sections TURN ON HEAT-
ERS, POWER LEVEL SELECTION and POWER LEVEL
ACCEPTANCE.
PRECISE LOW POWER may be combined with the Auto
Features BRIDGE and DOUBLE HEATER.
The PRECISE LOW keypad may be touched before or after
selecting the power level, BRIDGE or DOUBLE HEATER,
if using with those functions; but it must be touched before
touching the ON keypad again for the power level to be accepted,
or before 10 seconds pass and the power level is automatically
selected if no other keypads are touched.
If using with BRIDGE OR DOUBLE HEATER, the Heater
Digital Display will display BRIDGE and DOUBLE HEATER
Indicator Lights will illuminate. BRIDGE will sync both Heater
Digital Displays and “L” will ash alternately with the numeric
value of the power level set.
TURN PRECISE LOW POWER AND HEATER OFF
PRECISE LOW POWER may be turned OFF by the following
methods described in the section TURN OFF HEATERS:
1 Select and touch the heater OFF keypad.
OR
2 Select the heater by touching the ON keypad, then move the
power level to 0 on the Power Slider Bar. After 10 seconds,
a tone will sound, and the heater will turn OFF. The Hot
Surface/ON Indicator Light may still be illuminated until
the heater cools.
Either of the two methods described above will turn the heater
OF F.
TURN ONLY PRECISE LOW POWER OFF,
KEEP HEATER ON
PRECISE LOW can be turned OFF allowing the heater to switch
to the same numeric value at the regular power level scale.
For example, if you want to cancel PRECISE LOW 5 but
continue cooking with regular power level 5:
1 Select and touch the heater ON keypad.
2 Touch PRECISE LOW keypad, a tone will sound.
3 Touch the heater ON keypad again to accept the regular
power level.
4 The letter “L” will cease ashing on the Heater Digital
Display, only the number 5 will be displayed. The Power
Curve Display will adjust its scale to reect that the power
level is now set to regular 5.
WARNING
Never leave the cooktop unattended when cook-
ing. Boilovers cause smoking and greasy spillovers that may
catch on re. Do not allow pots and pans to boil dry or empty.
E17
E
SUGGESTED HEAT SETTINGS CHART
STANDARD AND PRECISE LOW
STANDARD SETTINGS
PRECISE LOW
SETTINGS
TYPE OF COOKING
SETTING NUMBERS NUMBERS
High 9-P N/A BOIL - Bring liquid to a boil. Always reduce setting to a lower heat when liquids
begin to boil, or foods begin to cook.
Medium High 7-8 N/A FRY - Brown meat, heat oil for deep fat frying or to continue a rapid boil.
Medium 5-6 (L 7-9) * SIMMER - Maintain a simmer or slow boil, thicken sauces and gravies.
Medium Low 3-4 (L 4-6) * WARM - Continue cooking covered foods, steam foods or maintain foods at a
warm temperature before serving.
Low 1-2 (L 1-3) * MELT - Melt butter or chocolate.
NOTE: The size and type of cookware used will inuence the setting needed.
* Precise Low Power Scale: Allows more detailed setting adjustment.
HOT SURFACE LIGHT INDICATOR
The Hot Surface/ON Indicator Light will remain ON until
a heater has cooled after use, even if cooktop main power is
turned OFF.
WARNING
In the event of a power failure to the home or to
the cooktop, be aware that SURFACES OF HEATERS WILL
REMAIN HOT even though the Hot Surface/ON Indicator
Lights ARE NO LONGER ILLUMINATED. The Hot Surface/
ON Indicator Lights will not come on automatically once power
has been restored.
AUTOMATIC TURN OFF
The maximum length of time a heater will remain ON depends
upon the power level selected.
POWER LEVEL SELECTED MAXIMUM TIME ON (HOURS)
1-8 10
9 3
TIMERS
A total of 5 timers may be set (for the 4 heaters and 1 indepen-
dent). The time can be set between 1 and 99 minutes and changed
at any point during the countdown. The nal minute will count
down in seconds on the display.
If using multiple timers, the default timer countdown displayed
will be the timer with the least amount of time, whether it is set
with a specic heater or independent timer. The Indicator Light
Timer ON will blink indicating that this is the time countdown
displayed. (See TIMER DISPLAY for more information.)
If the independent timer countdown has the least amount of time
remaining, it will be the default timer displayed and the Indicator
Light Timer ON light above the TIMER +/- keypad will blink
while the heater indicators will remain solid.
WARNING
This timer functions solely as a reminder and
does not control the cooking time of any heater, nor will it
switch off a heater.
TO SET A TIMER FOR A SPECIFIC HEATER
Select the heater and then either set power level, or touch the
+/- keypads rst, and then set the power level before the power
is accepted and the heater begins cooking. The timer and power
levels selected will be automatically accepted 5 seconds after
the last keypad is touched.
The default time displayed for the + keypad begins at 45 min-
utes. Touch +/- to increase in increments of 1 minute up to 99
minutes maximum. The default time displayed for the – keypad
begins at 0 with “00” displayed. If – keypad is touched again,
the countdown will begin at 99 minutes. Touch either keypad
to select increments of 1 minute, after reaching 10 minutes, the
scrolling increases rapidly.
USING THE COOKTOP
18E
E
OR
1 Select heater by touching ON keypad.
2 Use the Power Slider Bar selector to set power level.
3 Touch the TIMER +/- keypads; a tone will sound and the
Indicator Light Timer ON for the heater will blink. Use the
keypads to select desired time and touch ON again to accept.
4 Touch ON or wait 5 seconds for the power to be automatically
accepted and heater to begin heating.
5 A tone will sound and the Indicator Light Timer ON will
illuminate and remain on during the countdown. (If it is the
default timer countdown displayed, this light will blink.)
If using BRIDGE with the 2 left heaters, simply operate the
bridge function as instructed in the section BRIDGE HEATER
and select one of the TIMER keypads to set time as the heaters
will sync power and timer.
SET MULTIPLE TIMERS
Complete the steps for setting a single timer, and simply repeat
for the next desired heater.
SET AN INDEPENDENT TIMER
Simply select the +/- keypads and set a timer countdown. The
independent timer can be set even if the cooktop main power is
off (Control Lock must be deactivated). The independent timer
will continue to operate even if cooktop main power is turned
off. When setting the independent timer, a small red decimal
will ash at the bottom right corner of
the Timer Digital Display indicating that
this the independent timer is being set. It
will ash for 5 seconds, or until a heater
is selected.
When the timer countdown has completed, a tone will sound
(2 rapid succession beeps) and 00 will blink in the display for
1 minute or until any keypad is touched on the control panel.
SETTING A SINGLE TIMER
1 Select heater by touching ON keypad.
2 Touch the TIMER +/- keypads; a tone will sound and the
Indicator Light Timer ON for the heater will blink. Use the
keypads to select desired time and touch ON again to accept.
3 Use the Power Slider Bar selector to set power level.
4 Touch ON or wait 5 seconds for the power to be automatically
accepted and heater to begin heating.
5 A tone will sound and the Indicator Light Timer ON will
illuminate and remain on during the countdown. (If it is the
default timer countdown displayed, this light will blink.)
USING THE COOKTOP
E19
E
USING THE COOKTOP
TIMER DISPLAY
The default time displayed is the timer with the lowest time
remaining in its countdown. The timer displayed is indicated
by the Indicator Light Timer ON blinking.
When using a timer on multiple heaters, select the desired
heater by touching the ON keypad for that heater to view its
remaining time.
To switch to the independent timer, touch either the + or – pad.
When switching timer views, the timer display will show the
countdown selected for 10 seconds before switching back to the
default timer with the lowest remaining time.
TURN OFF TIMER
Touch heater ON keypad associated with the timer and either
touch the – keypad until the countdown reaches 0
OR
Touch the + and – keypads until the countdown turns off and
no digits are displayed.
If it is an independent timer, simply touch + and – keypads to
turn OFF.
NOTE: If the cooktop main power is turned off, the independent
timer will still count down.
20E
E
SPECIFICATION
SCR3042FB & SCR3041GB SCR2442FB
Product dimension (w x d x h) inch 30" x 21" x 2
5
/16" 24" x 21" x 2
5
/16"
Cut-out dimension (w x d) inch 28
5
/8" x 19
11
/16" 22
3
/8" x 19
11
/16"
Voltage (volts) / Amps 208V / 240V / 30 AMP 208V / 240V / 30 AMP
Frequency (Hz) 60 Hz 60 Hz
Total power (Watts) 7200 5500
Cooking Heaters 4 4
Left Rear / Boost
1500W 7" dia. 1500W 7" dia.
Left Front / Boost
1500W 7" dia. 1500W 7" dia.
Right Rear / Boost
1200W 6" dia. 700W 6" dia.
Right Front / Boost
3000W 9" dia. / 6" dia. 1800W / 750W 7" dia. / 4" dia.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Sharp SCR3042FB Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Sharp SCR3042FB User manual
