Electrolux EFLS210TIS Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur

Ce manuel convient également à

EN FRONT LOAD WASHER
FR LAVEUSE Á CHARGEMENT FRONTAL
USE & CARE GUIDE
GUIDE D’UTILISATION ET D’ENTRETIEN
157011532 January 2019
Important Safety Instructions
Read all instructions before using this
appliance. This book contains valuable
information about:
Operation
Care
Service
Keep it in a safe place.
This
Use and Care Guide
provides general
operating instructions for your washer. It also
contains information about features for several
other models. Your washer may not have
every feature included.
Use the washer only as instructed in this
Use
& Care Guide
.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
NOTE
The instructions appearing in this
Use and
Care Guide
are not meant to cover every
possible condition and situation that may
occur. Common sense and caution must
be practiced when installing, operating and
maintaining any appliance.
Electrolux model number
Electrolux serial number
Purchase date
Keep a record for quick
reference
The model and serial numbers of your washer
are found on the serial plate located inside
the door opening. Record and retain these
numbers.
Table of Contents
Important Safety Instructions ....................... 2
Features ...................................................... 5
Operating Instructions ................................. 6
Controls and Settings ................................ 11
Stain Removal Guide ................................. 17
Care and Cleaning ..................................... 19
Solutions to Common Problems ................ 24
Limited Warranty ....................................... 30
Table of Contents
Important Safety Instructions ....................... 2
Keep a record for quick reference ......2
Features ...................................................... 5
Operating Instructions ................................. 6
Normal Operating Sounds .................6
Operating Your Washer ......................7
Adding Laundry Products ..................9
Controls and Settings ................................ 11
Cycle Selection ................................ 11
Cycle Settings .................................13
Cycle Options .................................. 14
Other Features ................................15
Settings Chart .................................16
Stain Removal Guide ................................. 17
Safe Stain Removal Procedures ......17
Stain Removal Suggestions .............18
Care and Cleaning ..................................... 19
Inside Routine Cleaning (Preventive) 19
Performing Manual Drain .................20
Pump Filter Cleaning .......................20
Other Inside Routine Cleaning (Preventive) .............................. 21
Inside Cleaning (Aggressive) ............22
Outside Routine Cleaning ................23
Winterizing Instructions ....................23
Solutions to Common Problems ................ 24
Common Washing Inquiries .............24
Service Prevention Checklist ............27
Limited Warranty ....................................... 30
2
Important Safety Instructions
Definitions
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
Recognize Safety Symbols, Words
and Labels
Safety items throughout this manual are
labeled with a WARNING or CAUTION based
on the risk type as described below:
IMPORTANT
Indicates installation, operation, or
maintenance information which is important
but not hazard-related.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING
Please read all instructions before using this
washer.
WARNING - RISK OF FIRE
To reduce the risk of fire, electrical shock, or injury to persons when using this washer, comply
with the basic warnings listed below. Failure to comply with the Important Safety Instruction
warnings could result in property damage, serious personal injury, or death.
Prevent Fire
DO NOT wash items that have been
previously cleaned in, soaked in, or spotted
with gasoline, cleaning solvents, kerosene,
cooking oils, waxes, or other flammable
or explosive substances. DO NOT store
these items on or near the washer. These
substances give off vapors or chemical
reactions that could ignite or explode.
DO NOT put oily or greasy rags or clothing on
top of the washer. These substances give off
vapors that could ignite the materials.
DO NOT add gasoline, cleaning solvents, or
other flammable or explosive substances to
the wash water. These substances give off
vapors that could ignite or explode.
Under certain conditions, hydrogen gas
may be produced in a hot water system that
has not been used for 2 weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot
water system has not been used for such a
period, before using the washer, turn on all
hot water faucets and let the water flow from
each for several minutes. This will release any
accumulated hydrogen gas. Hydrogen gas is
flammable; DO NOT smoke or use an open
flame during this time.
DO NOT store or use gasoline or other
flammable vapors or liquids in the vicinity of
this or any other appliance.
Failure to comply with these warnings could
result in fire, explosion, serious bodily injury,
and/or damage to the rubber or plastic parts
of the washer.
DO NOT continue to use the washer if you
hear squeaking, grinding, rubbing, or other
unusual noises. This could be a sign of
mechanical breakdown and lead to fire or
serious injury. Contact a qualified technician
immediately.
Protect Children
DO NOT allow children to play on or in the
washer. Close supervision of children is
necessary when the washer is used near
children. As children grow, teach them the
proper, safe use of all appliances.
Destroy the carton, plastic bag, and other
packing materials after the washer is
unpacked. Children might use them for play.
Cartons covered with rugs, bedspreads, or
plastic sheets can become airtight chambers.
Keep laundry products out of children’s
reach. To prevent personal injury, o bserve
all warnings on product labels.
Before the washer is removed from service
or discarded, remove the washer door to
prevent accidental entrapment.
Failure to comply with these warnings could
result in serious personal injuries.
3
Important Safety Instructions
Prevent Injury
To prevent shock hazard and assure
stability during operation, the washer must
be installed and electrically grounded by
a qualified service person in accordance
with local codes.
Installation Instructions
are packed in the washer for installer’s
reference. Refer to
Installation Instructions
for detailed grounding procedures. If the
washer is moved to a new location, have
it checked and reinstalled by a qualified
service person.
To prevent personal injury or damage to
the washer, the electrical power cord of the
washer must be plugged into a properly
grounded and polarized 3-prong outlet.
The third grounding prong must never be
removed. Never ground the washer to a gas
pipe. DO NOT use an extension cord or an
adaptor plug.
Prevent Injury And Damage To The
Washer
WARNING
FIRE/ELECTRICAL SHOCK HAZARD
Avoid fire hazard or electrical shock. DO
NOT use an adaptor plug or extension cord
or remove grounding prong from electrical
power cord. Failure to follow this warning
can cause serious injury, fire or death.
WARNING
HARMFUL VAPOR HAZARD
DO NOT use or mix liquid chlorine bleach
with other household chemicals such
as toilet cleaners, rust removers, acid
or products containing ammonia. These
mixtures can produce dangerous fumes
which can cause serious injury or death.
Grounding type wall receptacle
Power cord with
3-prong grounded plug
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
To prevent serious personal injury and damage
to the washer:
All repairs and servicing must be performed
by an authorized service technician unless
specifically recommended in this
Use & Care
Guide
. Use only authorized factory parts.
DO NOT tamper with controls.
DO NOT install or store the washer where it
will be exposed to the weather.
DO NOT install on carpet. Install washer on
a solid floor. It may be necessary to reinforce
the floor to prevent vibration or movement.
DO NOT sit, step or stand on the washer.
Doing so may cause damage to the unit.
To reduce the risk of electric shock,
disconnect this appliance from the
power supply before attempting any user
maintenance. Canceling a cycle or turning
controls to the OFF position DOES NOT
disconnect this appliance from the power
supply.
To prevent injury, DO NOT reach into
the washer while parts are moving. Before
loading, unloading, or adding items, press
the Power button to stop the cycle. Allow
the wash tub to coast to a complete stop
before reaching inside.
This washer is equipped with an electrical
overload protector. The motor will stop if it
becomes overheated.
Failure to comply with these warnings could
result in serious personal injuries.
Follow package directions when using
laundry products. Incorrect usage can
produce poisonous gas - resulting in serious
injury or death.
DO NOT combine laundry products for use
in 1 load unless specified on the label.
DO NOT mix chlorine bleach with ammonia
or acids such as vinegar.
4
Features
Control Lock
Door Latch
with Safety
Lock
Laundry Product
Dispenser Drawer
Cascading
Wash Vanes
Pump Filter
Cleanout
Stainless Steel
Wash Drum
Adjustable
Leveling Legs
LED Display
Door Striker
Inner glass with small
article redistribution
ramp
As an ENERGY STAR
®
Partner, Electrolux
Major Appliances has determined that this
product meets the ENERGY STAR
®
guidelines for energy efficiency.
5
Operating Instructions
Normal Operating Sounds
You may or may not hear the following sounds
from your new washer:
A. DRAIN HOSE The washer has a flexible
drain hose to carry water from the washer
to the stand pipe of your home. You will
hear water flowing into your stand pipe.
This is a normal part of the operation of
the washer.
B. WATER VALVES/DISPENSER As
water enters the dispenser system, it is
common to hear a water flowing sound.
This normal sound will vary slightly based
on the water pressure in your home.
C. DOOR LOCK Your washer is equipped
with a door lock with an electric solenoid.
There will be a clicking sound as the
washer door is being locked or unlocked.
D. DRAIN PUMP Your washer is equipped
with a high velocity drain pump. It is
normal to hear humming and gurgling
sounds as water is pumped from the
washer. Both of these sounds are normal
and indicate that your pump is functioning
correctly.
E. HIGH SPEED MOTOR A powerful motor
is used to drive the drum to high spin
speeds to extract water from your load.
You will hear a sound associated with
these higher spin speeds. This sound is
normal and will vary slightly as the spin
speed varies with load size and cycle
selected.
A
B
C
D
E
CAUTION
Abnormal, on-going sounds may be an
indication of a pending washer failure
and should be investigated by a qualified
technician. Refer to “Noise” section of
Service Prevention Checklist in this manual.
6
Operating Instructions
Operating Your Washer
STEPS
TIPS IMPORTANT
1. Sort laundry
into loads
that can
be washed
together.
Sort by recommended cycle and water
temperature.
Separate white, light, and colorfast items
from dark and non-colorfast items.
Separate items that shed lint from items
that attract lint. Casual, synthetic, knit, and
corduroy items will pick up lint from towels,
rugs, and bedspreads.
Separate heavily soiled items from lightly
soiled items.
Separate lacy, sheer, loosely knit, or
delicate items from durable items.
DO NOT machine wash items
containing fiberglass. Small
particles of fiberglass left in
drum may transfer to fabrics
in other loads and cause skin
irritation and/or damage to
fabrics.
DO NOT wash water resistant
and water repellent type
clothing or other materials
2. Prepare
items for
washing.
Empty pockets.
Brush off lint and dirt. Shake out rugs and
beach towels.
Close zippers, fasten hooks, button
buttons, and tie strings/sashes. Remove
non-washable trims and ornaments.
Place delicate and small items (bras,
hosiery, etc.) in a mesh bag (not included).
Mend rips and tears to
prevent further damage during
washing.
Turn knit items inside out
to prevent pilling.
3. Pretreat
stains and
heavy soil.
See stain treatment function in
Cycle
Options
for your particular model or
Stain
Removal Guide
for more information.
4. Add laundry
load to
wash tub.
Combine large and small items in a load.
Load large items first.
Large items should not be more than half the
total wash load.
Washing single items is inefficient and may
cause an out-of-balance load. Add 1 or 2
similar items to help balance load.
The washer can be fully loaded, but the
items should not be tightly packed. The
door should close easily.
DO NOT overload the washer.
DO NOT WASH: Water
resistant and water repellent
clothing or other materials.
Make sure that NO items stay
between the seal and the door.
There is a risk of water leakage
or damage to the load.
WARNING
To reduce the risk of fire, electric shock or injury to persons, read the Important Safety
Instructions in this
Use & Care Guide
before operating your washer.
WARNING
RISK OF INJURY
DO NOT wash water resistant and water
repellent clothing or other materials. Failure
to follow these instructions may result in
an abnormal vibrating and out-of-balance
condition that could result in physical injury,
property damage, and/or appliance damage.
CAUTION
ENTRAPMENT and TIP-OVER HAZARD
DO NOT leave the door open if there are
small children or pets present. An open door
could entice children to hang on the door or
crawl inside the washer. If there are no small
children present, you may leave the door ajar
to prevent odor build up.
7
STEPS
TIPS IMPORTANT
5. Add laundry
detergent
and wash
products to
dispenser.
Detergent, liquid chlorine bleach and liquid
fabric softener will be dispensed at the
proper times in the cycle.
Water conditioners, detergent boosters
and enzyme products may be added with
detergent.
See
Adding Laundry Products
for detailed
information on the use of various wash
products (detergent, bleach, stain treatment,
fabric softener, etc).
See
Adding Laundry Products
for detailed
information on the use of the product
dispensers.
Use ONLY low-sudsing, high
efficiency detergent to prevent
oversudsing.
Follow manufacturer’s
instructions and
recommendations when using
wash products.
Open and close the dispenser
drawer slowly. Closing the
drawer too quickly could
result in early dispensing of the
bleach or fabric softener.
6. Select the
cycle and
settings for
the load.
See
Cycle Selection, Cycle Settings, and
Cycle Options
for detailed descriptions of
cycle controls.
See
Cycle Setting Charts
to determine which
settings are available for each cycle.
To provide the best care, not every setting
or option is available with every cycle. If a
setting or option is not available for the cycle
selected, the indicator will not light.
Follow fabric care label
instructions on items to be
washed.
7. Start the
washer.
Close the door and press Start/Pause. The
washer will not operate with the door open.
Check the door” will be displayed as a
reminder to close the door.
To add a forgotten item to the wash drum,
press Start/Pause and open the door.
Pause” will be displayed along with the
estimated remaining cycle time. Add the
item, close the door and press Start/Pause
to resume the cycle.
To change settings or options after the cycle
has begun, press Start/Pause, change
the settings, and then press Start/Pause.
Pressing the icons without pausing first
will emit several beeps but not change the
settings.
To change the cycle once the cycle has
begun, press the Power button to turn OFF
the washer, press the Power button to turn
ON washer again, select a new cycle, and
press Start/Pause. Just pressing another
cycle icon will not change the cycle.
To stop a cycle, press the Power button.
A signal will sound at the end of the cycle if
the chime option has been selected.
DO NOT force door open. As
a safety measure, the door will
automatically lock during the
entire wash cycle and the door
lock indicator will be lighted.
Pause or cancel the wash
load to unlock the door.
If the cycle is interrupted
during spin, the door lock will
not release until the tub has
stopped spinning.
If the water level is above the
bottom of the door opening/
flexible door gasket, the lock
will not release.
8. Remove
items from
washer
when cycle
has ended.
Remove items when the cycle ends and
place in dryer, line dry or dry flat as directed
on the fabric care label.
Excess wrinkling, color transfer
or odors may develop in items
left in the washer after the
cycle has ended.
Operating Instructions
8
Adding Laundry Products
Use a low-sudsing, high efficiency
detergent to prevent oversudsing in
front load washers. Look for this
symbol on the detergent label:
For best results
Detergent, liquid chlorine bleach and liquid
fabric softener will be dispensed at the proper
times in the cycle.
IMPORTANT
Open and close the dispenser drawer
slowly. Closing the drawer too quickly could
result in early dispensing of the bleach or
fabric softener
Mainwash - Liquid Detergent
Ensure the flap is in the downward position.
Add the recommended amount of liquid
detergent to the “Main Wash” compartment.
Mainwash
Use the cap or scoop provided by the
detergent manufacturer to measure the
amount recommended. Detergent dosage may
need to be adjusted for water temperature,
water hardness, load size and soil level.
IMPORTANT
Do not mix liquids and powders.
NOTE
From time to time you may see water in the
main wash (liquid) chamber. This is part of
the normal operation of the washer.
Place the main detergent flap in the downward
position for liquid detergent.
IMPORTANT
Use of multi-product (detergent plus
softener) sheets or color-absorbing sheets
NOT recommended. They could disable
your machine and result in unwarranted
repair costs.
Prewash
Bleach
Mainwash
Fabric Softener
Detergent flap
(Mainwash)
Operating Instructions
9
Operating Instructions
Mainwash - Other Wash Products
Color safe bleach, water conditioner,
detergent booster and enzyme products may
also be added to the Mainwash dispenser with
the detergent.
IMPORTANT
Do not mix liquids and powders.
• Put liquid products with liquid detergent
in the mainwash (liquid) chamber.
• Put powder products with powder
detergent in the mainwash (powder)
chamber.
Prewash
For heavily soiled or stained loads, select the
prewash option. Add the recommended
amount of detergent to the prewash detergent
compartment.
Liquid Chlorine Bleach
If desired, add liquid chlorine bleach to the
Bleach chamber.
DO NOT fill above the maximum fill line.
Add color-safe bleach with the detergent.
Liquid Fabric Softener
If desired, pour the recommended amount of
liquid fabric softener into the chamber marked
with this symbol .
Fill to the MAX line for large loads.
DO NOT fill above the maximum fill line.
Use of a fabric softener-dispensing ball
is not recommended in tumble action
washers.
IMPORTANT
To prevent fabric damage, do not overfill
the Bleach chamber or pour liquid chlorine
bleach directly onto the load.
Mainwash - Powder Detergent
Ensure the flap in the upward position.
Add the recommended amount of high-
efficiency powder detergent to the “Main
Wash” detergent chamber.
Place the main detergent flap in the upward
position for powder detergent.
Detergent Packs
Add detergent pack directly to the empty drum
BEFORE placing laundry into the unit.
CAUTION
Keep detergent packs away from children.
IMPORTANT
Do not place detergent packs into the
detergent drawer. The gel coating may
cause the detergent drawer to become
clogged.
NOTE
To prevent staining, DO NOT overfill the
fabric softener chamber or pour liquid fabric
softener directly on the wash load.
10
Cycle Selection
Press the Power button to turn on the
unit. Press the icon for the cycle desired
and the indicator for that cycle will be
illuminated. The estimated cycle time, rinse
water temperatures, final spin speed, and soil
level for each cycle will be indicated for the
cycle selected. In most cases cycle settings
and options can be changed. “See Cycle
Settings”, “Cycle Options”, and “Setting Chart”
for more details.
Start/Pause
My Favorites
Soil Level
light
sanitize
eco cold
high
extra heavy
heavy
medium
extra light
delay
start
prewash
eco
friendly
fresh
rinse
spin
steam
cycles
heavy
duty
normal
delicates
casual
NSF Protocol P172
Sanitization Performance of Residential
and Commercial, Family-Sized Clothes
Washers
Controls and Settings
Not all cycles, options, or features listed are available on every model. Console shown
above for reference only. Your model may differ.
Power My Favorites
Cycle Options / Cycle Status Display
Cycle Selection
Soil Level Start/Pause
NOTE
Only sanitizing cycles have been designed to
meet the requirements of NSF P172 protocol
for sanitization efficacy.
Follow the fabric care
label instructions.
For best results
The wash water is heated by an internal boost
heater as the load tumbles. Cold water is added
to cool down the load prior to drain and spin.
normal
Select for cotton, linen, towels, shirts, sheets,
denims and mixed loads.
deep clean sanitize
Select to clean and sanitize heavily soiled,
colorfast fabrics including towels, bedding,
and children’s clothing.
It is recommended that you set your water
heater to 120°F (49°C) or higher to ensure
proper performance during this cycle. If the
setting is lower or the load is extra large, the
cycle time will be extended by 30 mins or more.
The deep clean sanitize cycle will kill 99.9%
of bacteria with no carryover of bacteria
NOTE
To change the cycle once the cycle has
begun, press the Power button to cancel
the current cycle, press the Power button to
turn on unit again, select a new cycle, and
press Start/Pause. Just pressing another
cycle icon will not change the cycle.
between loads. No bleach or harsh chemicals
are needed, but higher temperatures are
required. Please check fabric care labels to
prevent damage.
NOTE
If the voltage at your outlet is under 110 V
the internal heater may not adequately heat
the wash water. If the cycle is interrupted
while the water is heating, the final
temperature of the wash water may be lower
and sanitization may be reduced.
heavy duty
Use this cycle for heavily soiled, durable
garments - ex. towels, sports gear, or fabric
tote bags. For best soil and stain removal, use
the hottest water safe for the fabrics being
washed.
casual
Select for cottons and blends with a
permanent press or no-iron finish.
11
Steam Cycle Selection
To scroll through the steam cycles, continue
to press the steam cycles icon. The selected
cycle will be displayed on the text display.
Specialty Cycle Selection
To scroll through the specialty
cycles, continue to press the
specialty cycles icon. The
selected cycle will be shown on the text
display.
fast wash
Quickly wash a small, lightly soiled load in 22
minutes.
whites
Use for white fabrics and lightly colored
clothing. Refer to fabric care label for use
of liquid chlorine bleach. Hot water is
recommended to ensure optimal bleach
activation. For peak rinsing performance and
to avoid chlorine residues on your laundry add
fresh rinse to this cycle.
wool
Use for a small load of machine-washable
woolen items, the wool cycle uses gentle
washing action along with cold rinses to
eliminate shrinking and damage to wool. You
may use an wool detergent approved for
front load washers.
Controls and Settings
IMPORTANT
If washer is paused during the steam portion
of a steam cycle, the door will remain locked
due to higher temperature in drum. DO NOT
force open - it will unlock upon cooling.
NOTE
• Steam may not necessarily be visible
inside drum during the steam cycles.
• Steam may not be present during entire
cycle.
NOTE
Steam refresh is not a washing cycle. It is
intended for clean, dry clothes. Take care not
to load items with stains.
NOTE
Washing wool garments labeled “Dry Clean
Only” or using chlorine bleach can result in
permanent damage.
steam refresh
Refresh a small load of dry clothes with the
perfect amount of steam. Steam alone will
infuse into the dry load as it tumbles to refresh
fabrics, remove odors, and release wrinkles,
reducing ironing. Remove load, hang or iron
as necessary.
normal with steam
Steam cycle for cotton, linen, towels, shirts,
sheets, denims and mixed loads.
casual with steam
Steam cycle for cottons and blends with a
permanent press or no-iron finish.
jeans
Select this specialty cycle for washing an
entire load of lightly to normally soiled denim
jeans or similarly-colored cotton khakis.
clean washer
To clean and freshen the washer, perform the
clean washer cycle. This maintenance cycle
uses hot water and two cold rinses to remove
residue that may cause odor. See “Inside
Routine Cleaning (Preventive)” for detailed
information about the clean washer cycle.
NOTE
You may deselect fresh rinse if you wish to
perform a spin only cycle or select no spin if
you want to perform a drain only cycle.
delicates
Select for lightly soiled knits and delicates
which require gentle washing.
rinse & spin
Select for loads that need a cold water rinse
or to add fabric softener that may have been
omitted in a regular cycle. Add the fabric
softener to the dispenser chamber. Select the
spin speed appropriate for the load.
12
Controls and Settings
Cycle Settings
Appropriate wash temperature, spin speeds,
soil level and options will be displayed for each
cycle. The settings can be changed before the
cycle is started. Make modifications according
to fiber content, colorfastness and soil level. If
changes are attempted after the cycle starts
a signal will beep and “Not possible” will be
displayed.
Spin Speed
Max, high, medium and low spin speeds are
available for each cycle. The spin speed and/
or duration of final spin vary from model to
model and cycle to cycle.
Increasing the spin speed will extract more
water, decrease drying time and conserve
energy. Decreasing the spin speed will reduce
wrinkling.
Select low spin speed to gently spin items
that should be line dried.
Use no spin to omit all intermediate spinning
phases and the final spin at the end of the
cycle. The load will be very wet. Remove items
from the wash drum to drip dry or select a
rinse & spin cycle to remove excess water at a
more convenient time.
Soil Level
Adjust the wash time based on the soil level
of each load. Extra heavy, heavy, medium,
light, and extra light soil levels are available.
NSF Protocol P172
Sanitization Performance of Residential
and Commercial, Family-Sized Clothes
Washers
hot
Use this setting for heavily soiled white or
colorfast cottons and blends.
warm
Use this setting for normally soiled white or
colorfast cottons or blends.
cold
Some warm water will automatically blend with
cold tap supply to achieve a precise cold.
Use this setting for lightly soiled non-colorfast
items, knits, delicates, and hand washables.
eco cold
Wash and rinse temperatures are equivalent
to temperature of cold tap supply. Use this
selection for fabrics and colors that are prone
to dye transfer. For use with cold water
detergents.
Wash Water Temperature
To change the preset temperature, press the
temperature icon to scroll to the desired
setting. A cold water rinse saves energy and
reduces wrinkling.
To protect your fabrics, not all temperatures
are available with every cycle. The indicator
will not light if the setting is not available with
that cycle.
Wash water temperatures are automatically
regulated to maximize detergent effectiveness
and improve washing performance. The
water heater setting and its distance from
the washer, water usage in other parts of
the home, and seasonally low ground water
temperature in some geographic areas can
affect water temperature.
sanitize
This setting sanitizes heavily soiled colorfast
fabrics such as towels, bedding, and
children’s clothing by killing 99.9% of bacteria
using wash water heated with a boost heater.
Cold water is used to cool and rinse the load.
NOTE
Only sanitizing cycles have been designed to
meet the requirements of NSF P172 protocol
for sanitization efficacy.
NOTE
To change the settings once the cycle has
begun, press the Start/Pause button, make
the new selection and press Start/Pause
again.
Follow the fabric care
label instructions.
For best results
13
Controls and Settings
Cycle Options
To add options, press the corresponding
option’s icon to illuminate the selection
desired. To delete options, press the option’s
icon again and the indicator light will turn off.
To change the options once the cycle has
begun, press the Start/Pause button, make
the new selection and press Start/Pause
again. Not all options are available on every
model.
To protect your fabrics, not all options are
available with every cycle. If an option is not
appropriate for the cycle, the indicator will not
light. Occasionally, a setting and option in the
same cycle will conflict with each other, like no
spin (or low spin) and eco friendly. When
this happens, the eco friendly option will
override any incompatible selections.
NOTE
To change the options once the cycle has
begun, press the Start/Pause button, make
the new selection and press Start/Pause
again.
prewash
Select this option to add a short initial wash
period to a cycle. Heavily soiled and stained
loads will prewash for approximately 15-20
minutes. The water will drain and the load will
automatically advance to the regular wash
cycle.
fresh rinse
Use this option when additional rinsing is
desired to remove excess dirt and detergent.
It is recommended for heavily soiled loads or if
household members have sensitive skin.
eco friendly
The eco friendly option reduces the amount
of hot water usage and total cycle duration to
to save energy. See Washer Settings Chart for
compatible cycles.
14
Other Features
My Favorites
After some time of initial usage, the washer
will automatically remember the 3 most used
cycles with their settings and options. To cycle
through this list continue to press the My
Favorites button. Press Start/Pause after
your desired cycle appears.
Door Lock Indicator
While the cycle is in progress the door lock
indicator will be lit. When the indicator is lit,
do not force open the door. Wait until the
indicator is off.
Chime
A chime will sound at the end of the cycle
when this option is selected. The signal can be
turned on or off by pressing the fresh rinse
and eco friendly icons at the same time.
Delay Start
Press delay start to select a wash time
convenient to your schedule or during off peak
energy hours. The delay time selected will be
displayed and begin counting down when you
select Start.
Control Lock
To avoid having someone accidentally start or
stop the washer, press prewash and fresh
rinse at the same time and hold until the
indicator is lit. To unlock the controls, press
prewash and fresh rinse at the same time
and hold until the indicator is no longer lit.
Controls and Settings
chime on/off
key combination
fresh rinse
default
key combination
control lock
key combination
My Favorites door lock
indicator
status display
delay start
cycle count down/
delay start timer
control lock
indicator
Status Display/Timer
The estimated total cycle time will be
displayed when the cycle is selected. The
time may increase if water pressure is low,
oversudsing occurs or the load becomes
unbalanced. The estimated remaining cycle
time is displayed during the cycle.
Fresh Rinse Default
To programme your unit to perform a default
fresh rinse at the end of every compatible
cycle, press prewash and delay start icons
simultaneously. Press fresh rinse to turn it
off for any given cycle while in default fresh
rinse mode. To turn default fresh rinse
mode off, press prewash and delay start
again til fresh rinse light turns off.
Pump Cleanout/Manual Drain
In the event the washer will not drain under its
own power due to a power outage or clogged
drain pump you can drain the water left in the
tub manually. See the Pump Filter Cleaning in
Care and Cleaning section.
15
Controls and Settings
Settings Chart
normal
deep clean
sanitize
heavy duty
steam cycles
casual
delicates
rinse & spin
specialty cycles
steam refresh
normal with
steam
casual with
steam
fast wash
whites
wool
jeans
clean washer
temperature
sanitize
NO OPTIONS AVAILABLE WITH THIS CYCLE.
DO NOT LOAD ANY ITEMS IN DRUM DURING CLEAN WASHER CYCLE.
hot
warm
cold
eco cold
spin speed
max
high
medium
low
no spin
soil level
extra heavy
heavy
medium
light
extra light
options
fresh rinse
prewash
eco friendly
add steam
delay start
chime
= Available selections. = Cycle defaults. = Non-modifiable presets.
These Temperature, Dryness Levels, and Options are available with the following cycles:
16
Follow the fabric care label
instructions on items to be washed.
For best results
Safe Stain Removal
Procedures
To reduce the risk of fire or serious injury to
persons or property, comply with the basic
warnings listed below:
Read and comply with all instructions on
stain removal products.
Keep stain removal products in their original
labeled containers and out of children’s
reach.
Thoroughly wash any utensils used.
Do not combine stain removal products,
especially ammonia and chlorine bleach.
Dangerous fumes can result.
Never wash items which have been
previously cleaned in, washed in, soaked
in or spotted with gasoline, dry cleaning
solvents or other flammable or explosive
substances because they give off vapors
that could ignite or explode.
Never use highly flammable solvents, such
as gasoline, inside the home. Vapors can
explode on contact with flames or sparks.
Stain Removal Guide
For Successful Stain Removal:
Remove stains promptly.
Determine the kind of stain, then follow
the recommended treatment in the stain
removal chart on the next page.
To pretreat stains, use a prewash product,
liquid detergent, or a paste made from
powder detergent and water.
Use cold water on unknown stains as hot
water can set stains.
Consult care label instructions for treatments
to avoid on specific fabrics.
Check for colorfastness by testing stain
remover products on an inside seam.
Rinse and wash items after stain removal.
WARNING
HARMFUL VAPOR HAZARD
Do not use or mix liquid chlorine bleach with
other household chemicals such as toilet
cleaners, rust removers, acid or products
containing ammonia. These mixtures can
produce dangerous fumes which can cause
serious injury or death.
17
Stain Removal Guide
Stain Removal Suggestions
STAIN TREATMENT
Adhesive tape, gum,
rubber cement
Apply ice. Scrape off excess. Place stain down on paper towels. Saturate
with prewash stain remover or nonflammable dry cleaning fluid.
Baby formula, dairy
products, egg
Use product containing enzymes to pretreat or soak stains. Soak for
30 minutes or more. Wash.
Beverages (coffee,
tea, soda, juice,
alcoholic beverages)
Pretreat stain. Wash using cold water and bleach safe for fabric.
Blood Rinse with cold water. Rub with bar soap. Or, pretreat or soak with
product containing enzymes. Wash using bleach safe for fabric.
Candle wax, crayon Scrape off surface wax. Place stain face down between paper
towels. Press with warm iron until wax is absorbed. Replace paper
towels frequently. Treat remaining stain with prewash stain remover or
nonflammable dry cleaning fluid. Hand wash to remove solvent. Wash
using bleach safe for fabric.
Chocolate Pretreat or soak in warm water using product containing enzymes.
Wash using bleach safe for fabric.
Collar or cuff soil,
cosmetics
Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white
fabric
Use packaged color remover. Wash using bleach safe for fabric.
Grass Pretreat or soak in warm water using product containing enzymes.
Wash using bleach safe for fabric.
Grease, oil, tar (butter,
fats, salad dressing,
cooking oils, car
grease, motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for
fabric. For heavy stains and tar, apply nonflammable dry cleaning fluid to
back of stain. Replace towels under stain frequently. Rinse thoroughly.
Wash using hottest water safe for fabric.
Ink Some inks may be impossible to remove. Washing may set some inks.
Use prewash stain remover, denatured alcohol or nonflammable dry
cleaning fluid.
Mildew, scorch Wash with chlorine bleach if safe for fabric or soak in oxygen bleach
and hot water before washing. Badly mildewed fabrics may be
permanently damaged.
Mud Brush off dry mud. Pretreat or soak with product containing enzymes.
Mustard, tomato Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Nail polish May be impossible to remove. Place stain face down on paper towels.
Apply nail polish remover to back of stain. Repeat, replacing paper
towels frequently. DO NOT use on acetate fabrics.
Paint, varnish WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once
paint is dry, it can’t be removed. OIL BASED AND VARNISH: Use solvent
recommended on label. Rinse thoroughly before washing.
Perspiration Use prewash stain remover or rub with bar soap. Rinse. Wash using
non chlorine bleach in hottest water safe for fabric.
Rust, brown or
yellow discoloration
Use rust remover safe for fabric. DO NOT use chlorine bleach because
it may intensify discoloration.
Shoe polish LIQUID: Pretreat with a paste of powder detergent and water. PASTE:
Scrape residue from fabric. Pretreat with prewash stain remover or
nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened
area. Wash using bleach safe for fabric.
Tomato Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Urine, vomit, mucus,
feces
Pretreat or soak in product containing enzymes. Wash using bleach
safe for fabric.
Wine Pretreat or soak in cold water. Wash in hottest water and bleach safe
for fabric.
18
To Refresh Or Clean Inside Of
Washer
To clean and freshen the washer, perform the
clean washer cycle. For best results use the
clean washer cycle once a month.
1. Press the Power button
to wake up the unit.
2. Press the specialty cycle
icon until clean washer
cycle is displayed.
3. Place the main detergent
flap in the upper position.
Inside Routine Cleaning
(Preventive)
To help prevent odors, mold or mildew, leave
the door open for a few hours after use or
whenever the washer is not in use.
Care and Cleaning
CAUTION
ENTRAPMENT and TIP-OVER HAZARD
Do not leave the door open if there are small
children or pets present. An open door
could entice children to hang on the door or
crawl inside the washer. If there are no small
children present, you may leave the door ajar
to prevent odor build up.
4. REMOVE ALL ITEMS FROM WASH
DRUM.
IMPORTANT
Items left in washer while performing the
clean washer cycle will cause a severe out-
of-balance situation that could damage the
washing machine.
Immediately follow up with a spin
cycle. Select fresh rinse on max spin
speed with no detergent or bleach to
help clear any residual bleach left after
the clean washer cycle.
For best results
5. Fill the detergent chamber with one (1)
cup of liquid chlorine bleach OR one (1)
pouch of TIDE
®
WASHING MACHINE
CLEANER. DO NOT use both.
6. Press Start/Pause to begin.
WARNING
HARMFUL VAPOR HAZARD
Do not use or mix liquid chlorine bleach with
other household chemicals such as toilet
cleaners, rust removers, acid or products
containing ammonia. These mixtures can
produce dangerous fumes which can cause
serious injury or death.
19
Performing Manual Drain
Pump Filter Cleaning
Care and Cleaning
With the wash tub
and drain hose
drained of all water
and the drain
spout snapped in
place, follow these
directions to remove,
clean, and reinsert
the pump filter.
1
2
1
2
In the event the washer will not drain under its
own power due to a power outage or clogged
drain pump you can drain the water left in the
drum manually.
180°
1
2
CAUTION
BURN HAZARD
Do not attempt to manually drain the drum
if it is full of hot water. Allow water to cool
before proceeding with manual draining.
2. Place a catch pan underneath the drain
pump filter to collect water as it drains.
3. Without removing the pump filter,
rotate the filter 180° counterclockwise to
allow the water to flow out into the catch
pan.
It may be necessary to close the filter and
drain the catch pan as it fills.
4. Repeat the process until all the water has
been drained.
NOTE
Always keep a rag nearby to clean any water
spills.
1. “Unscrew” the filter and pull it out.
2. Dump the filter and inspect the opening
for any loose objects.
3. Rinse the filter completely before putting it
back in place.
IMPORTANT
Check to make sure O-ring is in place
before reinserting pump filter. Take care to
not cross threads when turning pump filter
during reinsertion.
4. “Screw” filter back in place until it stops.
DO NOT overtighten.
5. Reinstall pump cleanout door if removed
earlier.
NOTE
You may have to add about 2 liters of clean
water through the mainwash detergent
compartment to reprime the drain pump.
pump filter cleanout
1. Remove pump cleanout door.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Electrolux EFLS210TIS Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues