Tripp Lite SmartOnline ® SUT 3-Phase UPS System 20/30/40/60kVA Le manuel du propriétaire

1

Owner’s Manual

SmartOnline

®

SUT

3-Phase UPS System

20/30/40/60kVA

Models: SUT20K, SUT30K, SUT40K, SUT60K

AG-01F9, AG-01FA, AG-01FB, AG-01FC

Input: 120/127V (Ph-N)

208/220V (Ph-Ph), 3ph 4-Wire + PE

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

Register your product for quicker service and ultimate peace of mind.

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

2

Table of Contents

1. Introduction ......................................................................................................................... 3

2. Important Safety Instructions ..............................................................................................4

2.1 Placement Warnings ......................................................................................................................................... 4

2.2 Connection Warnings ........................................................................................................................................ 4

2.3 Usage Warnings ................................................................................................................................................ 4

2.4 Storage Warnings ............................................................................................................................................. 5

2.5 Glossary of Symbols ......................................................................................................................................... 5

2.6 Standard Compliance ........................................................................................................................................ 6

3. Installation and Wiring .........................................................................................................6

3.1 Important Safety Warning ................................................................................................................................. 6

3.2 Transportation .................................................................................................................................................. 7

3.3 Delivery ............................................................................................................................................................ 7

3.4 Installation Environment ................................................................................................................................... 7

3.5 UPS Installation ................................................................................................................................................ 8

3.6 Wiring ............................................................................................................................................................ 10

3.6.1 Precautions Prior to Wiring ................................................................................................................... 10

3.6.2 Wiring Procedure .................................................................................................................................. 11

3.6.3 Parallel Units Wiring ............................................................................................................................. 14

3.7 External Battery Cabinet Connection Precautions ........................................................................................... 15

4. System Components ..........................................................................................................17

4.1 Appearance and Dimensions .......................................................................................................................... 17

4.2 Front View ...................................................................................................................................................... 17

4.3 Front View with Door Open .............................................................................................................................. 18

4.4 Control Panel ................................................................................................................................................. 19

4.5 Rear Panel ..................................................................................................................................................... 20

5. Operation Modes ............................................................................................................... 22

6. Communication Interfaces ................................................................................................25

7. Operation ...........................................................................................................................29

7.1 Connecting the UPS with Utility AC Power ....................................................................................................... 29

7.2 Turn On (Starting the Inverter) ......................................................................................................................... 29

7.3 Turn Off (UPS Shutdown) ................................................................................................................................. 29

7.4 Cold Start (Battery Start) Procedure ............................................................................................................... 29

8. LCD Display and Settings ....................................................................................................30

8.1 LCD Display Hierarchy .................................................................................................................................... 30

8.2 Setting Menu .................................................................................................................................................. 32

8.3 Parallel Screen .............................................................................................................................................. 35

8.4 Main Menu ..................................................................................................................................................... 36

8.5 Measure ........................................................................................................................................................ 36

8.6 Maintenance .................................................................................................................................................. 37

9. Optional Accessories ........................................................................................................39

10. Maintenance ......................................................................................................................39

11. Troubleshooting .................................................................................................................40

Appendix 1 : Technical Speciﬁcations .....................................................................................41

Appendix 2 : Warranty .............................................................................................................43

Español ................................................................................................................................... 44

Français ..................................................................................................................................87

3

1. Introduction

Tripp Lite’s SmartOnline SUT Series Uninterruptible Power Supply (UPS) is a Voltage and Frequency Independent (VFI) true on-line, double

conversion 3-Phase UPS system. The UPS continuously conditions the incoming electrical power supply, eliminating power ﬂuctuations

and interruptions that will otherwise damage sensitive electronic devices and cause system downtime.

The UPS applies the latest in DSP digital control technology and an output power factor up to unity. The efﬁciency of the UPS reaches

up to 94% in normal operation, and up to 98% in ECO mode, making it one of the most efﬁcient UPS systems in its class. In addition

to supplying clean, reliable and uninterrupted power to sensitive electronic devices at all times, the SmartOnline SUT produces greater

power efﬁciency at a lower cost.

With four different rated power levels – 20kVA, 30kVA, 40kVA and 60kVA – and offering paralleling capability up to 4 units, the UPS

offers multiple capacity options to suit the load’s requirements and offers the following features:

• True on-line UPS. Highest level of UPS protection, fully regulating the incoming power supply and transferring immediately to battery in

the event of an extended mains failure to continuously support critical loads.

• All digital, high frequency modulation technology, which decreases operating volume, improves reliability and prolongs service life.

• Wide AC input voltage range minimizes frequent transfer from normal operation to battery mode, saving battery consumption and

prolonging battery life.

• High efﬁciency – lower losses reduce cooling costs and extend system lifespan.

• Unity output power factor – more actual power allows more equipment to be supported.

• Programmable LCD allows users to conveniently set parameters for the UPS system; key operating conditions are visible via LCD for

accurate, clear monitoring.

• Serial, USB and volt-free contact communication as standard; SNMP and MODBUS options for optimum conﬁgurability. Monitoring and

management of the UPS via Tripp Lite’s free PowerAlert

®

power management software. Download at www.tripplite.com/poweralert.

• Automatic fan detection indicates whether fans are operating normally; multi-stage fan speed control improves their reliability and

efﬁciency, reduces operating noise and prolongs the service life of the fans.

• Both boost and ﬂoat charge are provided. The charge current is adjustable from 1A to 20A. Charging mode is linked to charging

current, maintaining the batteries at full charge capacity and extending battery life (ﬂoat charge voltage: 163.2V DC; boost charge

voltage: 168V DC).

The SmartOnline SUT UPS is ideally designed for protecting critical electrical equipment for:

• Data centers

• Telecommunications

• Computer network systems

• Medical treatment equipment

• Monitoring systems

• Light industrial

• Financial institutions

4

2. Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the installation, operation and storage of

this product. Failure to heed these instructions and warnings may affect the product warranty.

2.1 Placement Warnings

Install the UPS in a well-ventilated indoor area, away from excess moisture, heat, dust, ﬂammable gas or explosives. Leave adequate

space around all sides of the UPS for proper ventilation. Refer to 3.4 Installation Environment.

2.2 Connection Warnings

• The UPS must be well grounded due to a possible risk of current leakage.

• It is necessary to install protective devices and 4-pole contactors when the UPS is connected to the mains and bypass source.

For relevant information, refer to 3.6.1 Precautions Prior to Wiring.

• The protective devices connecting to the UPS must be installed near the UPS and must be easily accessible for operation.

2.3 Usage Warnings

WARNING:

To avoid any hazardous conditions during UPS installation and/or maintenance, these tasks must be performed

only by an engineer authorized by Tripp Lite. Proper startup procedures must be followed in order for warranty to

be valid. Contact Tripp Lite for further information.

• This is a class-A product. In a domestic environment, this product may cause radio interference, in which case, the user is required to

take adequate measures.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of

the life support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended.

• If the UPS needs to be connected to a motor load, it must be conﬁrmed by qualiﬁed service personnel.

• The parallel UPS systems can connect with common batteries. Before paralleling batteries, please make sure the battery voltage

difference between each UPS is lower than 5V DC.

• The external vents and openings in the UPS are provided for ventilation. To ensure reliable operation of the UPS and to protect the UPS

from overheating, these vents and openings must not be blocked or covered. Do not insert any object into the vents and openings that

may hinder ventilation.

• In a low temperature environment (below 32°F/0°C), you must allow the UPS to adjust to room temperature for at least one hour

before using to avoid moisture condensing inside the UPS.

• Do not place beverage containers or other liquids on the UPS, battery cabinet or any other accessory associated with the UPS.

• The risk of dangerous high voltage is possible when the batteries are still connected to the UPS even though the UPS is disconnected

from the mains. Do not forget to disconnect battery cables to completely cut off the battery source. For more information about battery

maintenance, refer to 4.3 Front View with Door Open.

• All maintenance services must be performed by qualiﬁed service personnel. To avoid risk of high-voltage electrical shock, do not open

or remove the UPS cover.

• Do not open or mutilate the battery or batteries. The released electrolyte is harmful to the skin and eyes and may be toxic.

• Do not dispose of the battery or batteries in a ﬁre. The batteries may explode.

• The batteries contain chemical substances that may jeopardize or pollute our environment. Please contact the supplier shown on the

batteries to properly dispose of the batteries.

• A battery can present a risk of electric shock and high short-circuit current. The following precautions should be observed before

replacement of batteries:

1. Remove watches, rings or other metal objects.

2. Use tools with insulated handles.

3. Wear insulating gloves and boots.

4. Do not lay tools or metal parts on the top of batteries.

5. Disconnect the charging source prior to connecting or disconnecting the batteries’ terminals.

• Contact qualiﬁed service personnel if either of the following events occur:

1. Liquid is poured or splashed on the UPS.

2. The UPS does not run normally after instructions in this Owner’s Manual are carefully observed.

5

2. Important Safety Instructions

2.4 Storage Warnings

Prior to Installation

If the UPS needs to be stored prior to installation, it should be placed in a dry area. The allowable storage temperature is 5~104°F

(-15~40°C).

After Usage

Press the OFF key (

OFF

) once and the LCD will appear with the below screen. To turn off the UPS, press the DOWN key ( ).

Make sure the UPS is in bypass mode, disconnect the UPS from the utility power, open the internal battery fuse holders (refer to

4.3 Front View with Door Open), remove all equipment from the UPS and store the UPS in a dry and well-ventilated area at a

temperature between 5~104°F (-15~40°C). Idle batteries must be fully recharged approximately every three months if the UPS needs to

be stored for an extended period of time. The charging time must not be less than 24 hours each time.

?

Transfer to Bypass Mode

YES( ) NO( )

2.5 Glossary of Symbols

No. Symbol Description

1

NORMAL

On-line mode LED indicator: green

2

BATTERY

Battery mode LED indicator: yellow

3

BYPASS

Bypass mode LED indicator: yellow

4

FAULT

Fault LED indicator: red

5

ON

ON key

6

OFF

OFF key

7

ESC

Goes back to previous screen or cancels current selection

8 Moves down/Decreases number

9 Moves up/Increases number

10 Conﬁrms selection

11

EPO

EPO key

12 R R phase of AC input/UPS output

13 S S phase of AC input/UPS output

14 T T phase of AC input/UPS output

15 N Input neutral line/Output neutral line/Battery neutral line

16 For UPS grounding

17 For critical load grounding/For external battery cabinet grounding

18 Positive battery terminal

19 Negative battery terminal

6

2. Important Safety Instructions

3. Installation and Wiring

2.6 Standard Compliance

This product meets the following safety standards and electromagnetic compatibility (EMC) inspection standards:

• UL 1778

• CSA C22.2 No. 107.3

• FCC Part 15 Class A (EMC)

• GB17626-2 / IEC 61000-4-2 (ESD) Level 4

• GB17626-3 / IEC 61000-4-3 (Radiated Field) Level 3

• GB17626-4 / IEC 61000-4-4 (EFT) Level 4

• GB17626-5 / IEC 61000-4-5 (Surge) Level 4

3.1 Important Safety Warning

Read this manual thoroughly before undertaking any installation and wiring. An authorized Tripp Lite engineer must perform the start-

up of the UPS and a completed start-up form must be returned to Tripp Lite in order to activate the SmartOnline SUT warranty. Please

contact your local supplier or [email protected] for further details. To ﬁnd your local contact, go to

www.tripplite.com/support/contacts and click on ‘Service Centers’.

Package Inspection

External

Inspect the UPS exterior packaging. If any damage is observed, immediately contact the dealer from whom the UPS was purchased.

Internal

(Male) (Female) (Female) (Female)

1 2 3

4 5

1. Check the rating label on the top of the UPS cabinet and

make sure the device number and capacity match what

you ordered.

2. Examine if any parts are loose or damaged.

3. The UPS package contains the items listed below. Please

check if any items are missing.

4. If anything is damaged or missing, immediately contact

the dealer from whom the UPS was purchased.

5. If the UPS needs to be returned, carefully repack the

UPS and all of the accessories using the original packing

material that came with the unit.

No. Item SUT20K SUT30K

SUT40K SUT60K

1

UPS (with internal batteries) 1 pc. 1 pc.

1 pc. 1 pc.

2

Owner's Manual 1 pc. 1 pc.

1 pc. 1 pc.

3

Test Card 1 pc. 1 pc.

1 pc. 1 pc.

4

RS-232 Cable (Male/Female) 1 pc. 1 pc.

1 pc. 1 pc.

5

Parallel Cable (Female/Female) 1 pc. 1 pc.

1 pc. 1 pc.

Notes:

1. The balance supports have been locked on the pallet when the UPS is shipped out of the factory. Keep them well maintained after unpacking, as it may

be necessary to use them for installation.

7

3. Installation and Wiring

3.2 Transportation

WARNING

The UPS is packed on a pallet suitable for handling with a forklift. If using a forklift or other equipment to move

the UPS, ensure its load bearing is sufﬁcient to support the total packing weight of the UPS.

The UPS is ﬁxed on the pallet with four balance supports. Do not discard the balance supports, as they may be required for installation

(see section 3.5 UPS Installation). When removing them, pay attention to the movement of the casters to avoid accidents.

The UPS cabinet may be pushed forward or backwards only; it may not be moved sideways.

If moving the UPS over long distance, use appropriate equipment such as a forklift; do not move the UPS cabinet using its attached

casters over long distances, move the UPS cabinet in its original packaging until at the ﬁnal destination site.

3.3 Delivery

Inspect the packaging materials and UPS cabinet carefully upon delivery. Do not install a damaged UPS, connect it to a battery or to

the utility. The packing box of the UPS is equipped with an anti-tilt device. Conﬁrm the device does not indicate any shock or excess tilt

during transit. If the device indicates there has been excessive shock or tilt, do not install and contact your local Tripp Lite representative.

3.4 Installation Environment

• The UPS is designed for indoor use only. Do not place or install the UPS in an outdoor area.

• When moving the UPS to its installation site, ensure all corridors, doors, gates, elevators, ﬂoors, etc. are able to accommodate and

bear the combined weight of the UPS system, any associated battery cabinets and all handling equipment. See Appendix 1 for UPS

combined weights.

• The installation site should have a dedicated AC circuit available, compatible with the UPS system’s input requirements. See

Appendix 1 for input speciﬁcations.

• Ensure the installation area has sufﬁcient space for maintenance and ventilation of the UPS system.

• Maintain the installation area’s temperature below 86°F (30°C) and the humidity level below 90%. The highest operating altitude is

6500 ft. (2000 m) above sea level. Please consider the derating values when operating the UPS over 3300 ft. (1000 m); refer to

Appendix 1. The optimum operating temperature for the batteries is between 68~77° (20~25°C).

• The UPS should be located in an environment with clean air and adequate ventilation to maintain the ambient temperature within the

UPS operating range.

• The UPS is air-cooled with the aid of internal fans. Do not cover the ventilation openings of the UPS system.

• Install the UPS in an area in which the walls, ﬂoors and ceilings are constructed with ﬁreproof materials. The UPS is suitable for

mounting on concrete or other non-combustible surfaces only.

• Install a CO

2

or dry powder extinguisher in the installation area.

• Ensure the installation area is adequately sized for maintenance and ventilation:

o Maintain a clearance of 3 ft. (1 m) from the front of the UPS.

o Maintain a clearance of 1.67 ft. (50 cm) from the rear and both sides of the UPS.

8

3. Installation and Wiring

3.5 UPS Installation

There are two installation methods. One is with the balance supports and the other is without the balance supports.

Installation without the Balance Supports

After moving the UPS to its ﬁnal installation area, use the levelers to stabilize the UPS cabinet on the ground.

(Figure 3-1: Stabilize the UPS with Levelers)

Installation with the Balance Supports

To reinstall balance supports removed from the UPS during the unpacking process, follow these steps:

1

Once the installation area has been selected, follow the mounting hole diagram below to drill holes.

(621.6 mm)

24.5 in.

(561.6 mm)

22.1 in.

(80 mm)

3.1in.

(80 mm)

3.1in.

(80 mm)

3.1in.

(80 mm)

3.1in.

(420 mm)

16.5 in.

(420 mm)

16.5 in.

Mounting Hole

(Diameter:ø12 mm)8 pcs.

Mounting Hole

(Diameter:ø6.5 mm)8 pcs

(Front)

(Back)

(Figure 3-2: Mounting Hole Diagram)

9

3. Installation and Wiring

2

Place the UPS over the drilled holes, use the levelers to stabilize the UPS on the ground and use the M6 screws to reinstall the

balance supports (that were removed from the UPS during the unpacking process) on the UPS. Refer to the ﬁgure below.

M6 Screw x 8

Balance Support x 4

(Figure 3-3: Balance Support Installation)

3

Use four user-supplied M8 bolts to ﬁx the four balance supports on the ground to avoid UPS movement.

Ground

M8 Bolts x 4

Balance

Support x 4

(Figure 3-4: Fix the Balance Supports on the Ground)

10

3. Installation and Wiring

3.6 Wiring

3.6.1 Precautions Prior to Wiring

• The wiring must be performed by qualiﬁed professional personnel.

• Before wiring or making any electrical connection, make sure the power supplied to the input and output of the UPS is completely cut

off and the internal battery connectors are disconnected.

• When connecting the UPS to the utility AC power and bypass source, protective devices and 4-pole connectors must be installed. The

protective devices and 4-pole contactors must use approved components that meet safety certiﬁcations. Please refer to the following

table for suggested protective devices. For the installation of the protective devices and 4-pole contactors, see Figures 3-10~3-18.

UPS System Recommended Protective Device

SUT20K D-Curve 75A circuit breaker

SUT30K D-Curve 125A circuit breaker

SUT40K

D-Curve 150A circuit breaker

SUT60K

D-Curve 225A circuit breaker

• When connecting the critical loads to the UPS, a listed certiﬁed breaker must be installed between them. Refer to the table below

UPS System Recommended 3-Pole Breaker

SUT20K C-Curve 75A circuit breaker

SUT30K C-Curve 125A circuit breaker

SUT40K

C-Curve 150A circuit breaker

SUT60K

C-Curve 225A circuit breaker

• Check that the size, diameter, phase and polarity of each cable connecting to the UPS is correct. For the speciﬁcations of input/output

cables and circuit breakers, refer to Table 3-1.

Table 3-1: Speciﬁcations of Input/Output Cables and Circuit Breakers

SUT20K SUT30K SUT40K SUT60K

AC Input Cable* 2 AWG (25 mm

2

) 1/0 AWG (50 mm

2

) 3/0 AWG (95 mm

2

) 250 kcmil (120 mm

2

)

Output Cable* 2 AWG (25 mm

2

) 1/0 AWG (50 mm

2

) 3/0 AWG (95 mm

2

) 250 kcmil (120 mm

2

)

Battery Input Cable* 1 AWG (35 mm

2

) 1/0 AWG (50 mm

2

) 3/0 AWG (95 mm

2

) 250 kcmil (120 mm

2

)

Tightening Torque 130 in. lb. (14.7 N·m) 130 in. lb. (14.7 N·m) 130 in. lb. (14.7 N·m) 130 in. lb. (14.7 N·m)

Input Breaker 75A (3-pole x 1) 125A (3-pole x 1) 150A (3-pole x 1) 225A (3-pole x 1)

* Use only copper wire rated to 194°F (90°C) or higher

Notes:

1. In accordance with local electrical codes, install a suitable conduit and bushing.

2. Please refer to national and local electrical codes for acceptable non-fuse breakers and cable size.

3. Cables with PVC material and with temperature resistance up to 201°F (105°C) are suggested.

4. Make sure that the input/output cables are locked tightly.

• When connecting with the external battery cabinet, conﬁrm the polarity. Do not reverse the polarity.

• The grounding cable of the external battery cabinet must be connected to the ( ) terminal of the battery terminal block.

• Installer should consider the maximum current and wiring gauge that may be required for future expansion of parallel conﬁgurations.

• The input of the UPS must be a Y connection, and the neutral line (N) must be connected to avoid UPS failure. Do not connect the

neutral line (N) of the UPS with the ground terminal ( ).

• If there is a ﬂoating voltage between the input power’s neutral (N) and the ground ( ) and you require that the VNG of the UPS

should be zero, it is suggested an installation transformer be installed in front of the UPS input side and the UPS neutral (N) be

connected with the ground ( ).

• The utility AC power must be three phases (R/S/T) and meet the speciﬁcations on the UPS rating label. When connecting the utility

input power to the UPS, make sure it is in positive phase sequence (clockwise phase rotation).

• Connect the external battery cabinet’s grounding terminal to the grounding terminal ( ) of the UPS system’s battery terminal block.

Do not connect the grounding terminal of the external battery cabinet to any other grounding system.

• The ground terminal ( ) of the UPS must be grounded. Use ring-type terminal for wiring.

11

3. Installation and Wiring

WARNING:

1. Incorrect wiring will lead to severe electric shock and damage to the UPS.

2. The UPS will not work normally if the input power's neutral (N) is not ﬁrmly connected or is not connected to

the AC Input Block's neutral (N) terminal.

3.6.2 Wiring Procedure

Note: Prior to wiring, ﬁrst read 3.6.1 Precautions Prior to Wiring.

1

Remove the cover plate to access the wiring terminal block shown in Figure 3-5.

CS

N R S T

N

R S T

4-Pole

Contactor

Protective

Device

CS:

Contactor

Solenoid

N R

S T

Output Breaker:

R S T

N

Connects to the

main AC source

N R

S T

Manual

Bypass

Breaker

R S T

N

For grounding

the Critical Loads

Connect to the

Critical Loads

For grounding

the UPS

(Figure 3-5: Single Unit Wiring Diagram)

1

2

3

4

12

2

Ensure the functions of the wiring terminal block shown in Figure 3-5 are clearly understood.

No. Item Function Description

1

AC Input

Terminal Block

Connects the main AC source Includes 3-phase (R, S, T) and neutral (N) terminals

2

For the UPS grounding Includes one grounding terminal

3

UPS Output

Terminal Block

Connects the critical loads Includes 3-phase (R, S, T) and neutral (N) terminals

4

For the critical loads’ grounding Includes one grounding terminal

5

Battery Input

Terminal Block

Connects an external battery

cabinet

Includes three terminals, positive (+), neutral (N) and negative (-)

6

For an external battery

cabinet’s grounding

Includes one grounding terminal

3

Conﬁrm the UPS rating voltage is 120/208V AC or 127/220V AC, and the battery rating voltage is ±144V DC.

4

Conﬁrm the input breaker is in the OFF position. For the position of each breaker, refer to unit’s front panel.

5

Select the proper input and output cables according to the UPS capacity (refer to Table 3-1).

6

Open the UPS front door to unscrew and remove the panel labeled “Battery Compartment”.

7

The UPS system is shipped with the battery cables disconnected. Remove the insulation tape covering the BAT(+) red wires and

reconnect to the terminals (Figure 3-6). Refer to Figures 3-7~3-10 for each model’s respective battery installation.

Internal Battery Installation

(Figure 3-6: Battery Cable Connection)

3. Installation and Wiring

13

8

Connect optional external battery to the external battery cabinet terminal block located at the lower right of the unit (refer to Figure

3-11).

3. Installation and Wiring

(Figure 3-7)

First connect the -1 and -2 cables on the left,

then the +1 and +2 cables on the right.

–1

and

–2

–1

through

–3

–1

through

–3

–1

through

–4

N1

and

N2

N1

through

N3

N1

through

N3

N1

through

N4

+1

and

+2

+1

through

+3

+1

through

+3

+1

through

+4

(Figure 3-8)

First connect the -1, -2 and -3 cables on the left,

then the +1, +2 and +3 cables on the right.

(Figure 3-9)

First connect the -1, -2 and -3 cables on the left,

then the +1, +2 and +3 cables on the right.

(Figure 3-10)

First connect the -1, -2, -3 and -4 cables on the left,

then the +1, +2, +3 and +4 cables on the right.

(Figure 3-11: Connect an external battery [optional] to the external battery cabinet terminal block.)

5

6

SUT20K

SUT60K

SUT30K

SUT40K

14

3. Installation and Wiring

3.6.3 Parallel Units Wiring

Note: Prior to wiring, ﬁrst read 3.6.1 Precautions Prior to Wiring.

1

Follow steps

1

~

5

in section 3.6.2 Wiring Procedure.

2

The UPS system is shipped with the battery cables disconnected. Locate the battery connection cables behind the labeled

connector door in the cabinet. Connect the battery cabinet cables to the wiring terminal block and ensure the UPS system is

properly grounded (refer to Figures 3-6~3-10).

3

Use the provided parallel cable to connect the parallel ports on the parallel units. See Figure 6-1 for parallel port location.

4

Refer to 6. Communication Interfaces to set the parallel switch in the ON or OFF position.

5

Follow steps

7

~

8

in section 3.6.2 Wiring Procedure.

WARNING:

1. When UPS systems are paralleled, the length of each unit’s input cables/output cables must be equal. This

ensures that the parallel UPS systems can equally share the equipment loads in bypass mode.

2. Only UPS systems with the same capacity, voltage and frequency can be paralleled; otherwise, parallel

functions will fail.

3. Before start-up of parallel units, qualiﬁed service personnel should set ID (0, 1, 2 or 3) through the LCD.

Otherwise, UPS systems cannot be started. If the symbol ‘!’ appears after an ID number, it indicates there is a

conﬂict between ID numbers.

UPS 1

UPS 2

UPS 4

I/P

LOAD

AC Input

UPS Output

Parallel Port

Parallel Cable

3Ø4W 3Ø4W

Parallel Cable

(Figure 3-12: Parallel Units Wiring Diagram)

15

3. Installation and Wiring

3.7 External Battery Cabinet Connection Precautions

WARNING:

1. Connect loads to the UPS only after the batteries are fully charged. This guarantees that the UPS can provide

sufﬁcient backup power to the loads connected when a power failure occurs.

2. When using both the UPS internal batteries and external batteries, ensure the voltage difference is <5V DC.

Battery

1. Charge Voltage

1) Float voltage: ±163.2V DC (default)

2) Boost voltage: ±168V DC (default)

2. Charge Current

1) Minimum: SUT20K/SUT30K/SUT40K/SUT60K

g

1A

2) Maximum: SUT20K

g

10A

SUT30K/SUT40K/SUT60K

g

20A

3) Default: SUT20K

g

5A

SUT30K

g

7.5A

SUT40K

g

7.5A

SUT60K

g

10A

3. Low Battery Shutdown: 120V DC (default: 120V DC)

4. Number of Batteries: SUT20K

g

48 pcs.

SUT30K

g

72 pcs.

SUT40K

g

72 pcs.

SUT60K

g

96 pcs.

Notes:

1. Charge current is adjustable from 1A to the 20A maximum in increments of 0.5A.

2. To modify the default charge current setting or default low battery shutdown setting, contact your local dealer or service personnel.

• Only use the same type of batteries from the same supplier. Never combine old, new or different Ah batteries at the same time.

• The number of batteries must meet UPS requirements.

• Do not connect the batteries in reverse polarity.

• When connecting a non-Tripp Lite external battery cabinet to the UPS, it is compulsory to install an appropriate non-fuse DC breaker

and fast-acting fuses (when short-circuit occurs, the melting current must be 5~6 times of the battery fuse’s rating current).

• To extend battery backup time, connect several external battery cabinets to the UPS.

Note: Recharge time will be extended; take note of charger capacity.

• To extend battery backup time, external batteries may be connected to the UPS.

Rating Power (kVA)

Circuit Breaker

Rating Current Battery Cable Battery Fuse

20 250V AC / 75A 1 AWG (35 mm

2

) 660V DC / 80A

30 250V AC / 125A 1/0 AWG (50 mm

2

) 660V DC / 125A

40 250V AC / 150A 3/0 AWG (95 mm

2

) 660V DC / 150A

60 250V AC / 250A 250 kcmil (120 mm

2

) 660V DC / 250A

16

• The breaker must be a 3-pole DC breaker with a 250V DC rating per pole. Follow Figure 3-13 or Figure 3-14 between the UPS

external battery cabinet.

External

Battery

Cabinet

-

N

+

-

N

+

UPS

3-pole Non-fuse

DC Breaker

Fast-acting

Fuses

(Figure 3-13: A 3-pole Non-fuse DC Breaker and Fast-acting Fuses Installation I)

External

Battery

Cabinet

3-pole Non-fuse

DC Breaker

Fast-acting

Fuses

UPS

-

N

+

-

N

+

(Figure 3-14: A 3-pole Non-fuse DC Breaker and Fast-acting Fuses Installation II)

3. Installation and Wiring

Battery Status Alarm

When the UPS system’s batteries experience one of the problems shown below, the system will sound the following alarms:

No. External Battery Cabinet Status Alarm

1 Battery Test Fail Sounds once every 2 seconds

2 Battery Low Warning Sounds once every 0.5 second

3 Battery Low Shutdown Long beep (5 seconds)

4 Battery Over Charge Sounds once every 2 seconds

5 Battery Missing Sounds once every 2 seconds

17

4. System Components

4.1 Appearance and Dimensions

SUT20K,

SUT30K

53.15 in.

(1350 mm)

SUT40K,

SUT60K

69.3 in.

(1760 mm)

All models

31.5 in.

(800 mm)

All models

20.5 in.

(521 mm)

(Figure 4-1: UPS Appearance and Dimensions)

1

LCD Display, Control Panel and LED Indicators

1. LCD displays UPS status.

2. Control panel includes ESC, move-up, move-down, conﬁrmation, ON/OFF and EPO buttons (refer to Figure 4-7).

3. LED indicators include NORMAL, BATTERY, BYPASS and FAULT.

4. See Chapter 8. LCD Display and Settings for more information.

4.2 Front View

LCD Display,

Control Panel and LED Indicators

1

(Figure 4-2: Front View)

18

4. System Components

4.3 Front View with Door Open

2

3

2

3

2

Input Breaker

Controls the UPS system’s main input switch and is used for safety protection.

3

Internal Battery Cabinet

The four UPS models have different contents inside the internal battery cabinet. See the table below for more information.

1. The internal battery cabinet includes:

No. Item

Quantity

SUT20K SUT30K SUT40K SUT60K

1 Internal Batteries 48 72 72 96

2 Battery Tray 12 18 18 24

2. The internal batteries, battery trays and battery cables shown in the above table have already been conﬁgured at factory.

Only qualiﬁed service personnel should perform battery installation, wiring and connection.

START UP and COMMISSIONING

An authorized Tripp Lite engineer must perform the start-up of the UPS and a completed start-up form must be

returned to Tripp Lite in order to activate the SmartOnline SUT-Series warranty. Please contact your local supplier or

intlser[email protected] for further details. To ﬁnd your local contact, go to www.tripplite.com/support/contacts and

click on ‘Service Centers’.

(Figure 4-3: SUT20K Front

View with Door Open and

Battery Compartment Panel

Removed.)

(Figure 4-4: SUT30K Front

View with Door Open and

Battery Compartment Panel

Removed.)

(Figure 4-5: SUT40K Front

View with Door Open and

Battery Compartment Panel

Removed.)

(Figure 4-6: SUT60K Front

View with Door Open and

Battery Compartment Panel

Removed.)

19

4. System Components

4.4 Control Panel

ESC

7

1

2

5

6

3

8

4

12

9

10

11

(Figure 4-7: Front Panel)

No. Item Description

1

NORMAL

UPS is operating in on-line mode and the utility AC power is normal.

2

BATTERY

UPS is operating in battery mode and the external batteries are discharging.

3

BYPASS

UPS is operating in bypass mode.

4

FAULT

UPS has abnormalities.

5

LCD Display

Displays UPS operating status and relevant monitoring data.

6

ON

ON key: Press this key for 3~4 seconds and release it after hearing a beep to start up the UPS.

7

OFF

OFF key: Press this key once and the LCD shows the following screen. To

shut down the UPS, press

the DOWN

key ( ).

?

Transfer to Bypass Mode

YES( ) NO( )

8

Conﬁrms selection and accesses menu screen.

9

Moves up/Increases number.

10

Moves down/Decreases number.

11

ESC

Goes back to previous screen or cancels current selection.

12

EPO

When an emergency event occurs, press the EPO key for more than one second to shut down the

rectiﬁer, inverter and output of the UPS immediately. To reset, disconnect the EPO key and push the

unit’s OFF button for 3 seconds, then push the unit’s ON button.

20

4.5 Rear Panel

4. System Components

(Figure 4-9: SUT40K, SUT60K Rear Panel)

(Figure 4-8: SUT20K, SUT30K Rear Panel)

1

2

3

7 8 9 10 11

12

14

13

14

4 5 6

1

2

3

7 8 9 10 11

12

14 13 14

4 5 6

La page charge ...

Tripp Lite SmartOnline ® SUT 3-Phase UPS System 20/30/40/60kVA Le manuel du propriétaire

Tripp Lite SmartOnline ® SUT 3-Phase UPS System 20/30/40/60kVA Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents