Croozer Dog 2014-2016 Le manuel du propriétaire

Marque: Croozer

Modèle: Dog 2014-2016

Catégorie: Poussettes

Taper: Le manuel du propriétaire

2 en 1

Remorque cyclable

Poussette

www.croozerdesigns.com

CroozerDog14-ENG-F-USACAN-2-14

124 009 914

OWNER’S MANUAL

ENGLISH

ENG

Croozer Dog

MODE D’EMPLOI

FRANÇAIS

2-in-1

Bicycle Trailer

Stroller

Read this manual before using this product. Failure to follow the instructions and safety precautions in this manual can

result in serious injury or death. Keep this manual in a safe location for future reference.

Avant utilisation, lisez ce mode d’emploi et conformez-vous aux consignes de sécurité et prescriptions qu’il contient. Le

non-respect de ces consignes et prescriptions peut être à l’origine d’accidents aux conséquences potentiellement mor-

telles. Conservez ce mode d’emploi en lieu sûr pour le cas où vous en auriez besoin ultérieurement.

CroozerDog14-ENG-USACAN-2-14

Safety Guidelines

ENG

Safety Guidelines

Symbols and warnings

DANGER indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

NOTICE indicates a situation which, if not avoided, could

result in damage to the Croozer Dog or the environment.

Tip: In this manual, “Tip” indicates helpful advice about

the use or maintenance of the Croozer Dog.

Read and observe this manual!

This manual contains information that is extremely impor-

tant for the safety of you, your dog, and other road users.

Therefore, it is essential that you read the entire manual

carefully and follow the instructions closely. If should

should experience dif culties understanding any of the

information or instructions, please contact your Croozer

dealer. Keep this manual handy at all times for future re-

ference. If you loan or sell your Croozer Dog, pass on this

manual to the new user. It is also vitally important that you

read and observe the instructions provided in the manual

of the towing bicycle.

Who can ride in the Croozer Dog?

The Croozer Dog is intended for use with dogs and other

small animals up to 19 inches (48 cm) in height (paws to

top of head when standing). The vehicle is designed to

carry a maximum weight of 88 lbs (40 kg).

Who can ride the towing bicycle?

Be sure to acquaint yourself with the applicable laws in the

state or country where you plan to use the Croozer Dog.

Requirements for the towing bicycle

The towing bicycle must be approved by its manufacturer

for pulling a trailer. This information can be found in the

owner’s manual of the bicycle. Furthermore, the towing

bicycle must be in perfect working order and have strong,

properly functioning brakes. The rear wheel of the towing

bicycle must be equipped with an effective splashguard.

Otherwise, your dog could be injured by stones and other

debris thrown up from the road. Motorized vehicles may

not be used for pulling Bicycle Trailers. The only exception

to this rule is a pedelec. This special type of e-bicycle has

an electric motor that delivers assist only when the rider

pedals. In many countries, pedelecs legally qualify as

bicycles. However, e-bikes with a maximum speed of more

than 12 mph (20 km/h) may not be used for pulling the

trailer. The towing bicycle should be equipped with a sturdy

rear-mount kickstand to ensure safety when loading and

unloading your dog.

Be sure to familiarize yourself with the legal requirements

that apply to towing bicycles in the country or state where

you will be using the Croozer Dog.

The towing bicycle must have a 26” or 28” (559 or 622mm)

rear wheel. This information can be found on the tire side-

walls. The numbers 42-622, for example, indicate that the

tire has a width of 42 mm and a bead-seat diameter of 622

mm (28 inches).

Legal requirements for using a Bicycle

Trailer

Be sure to familiarize yourself with the legal requirements

that apply to pulling a Bicycle Trailer in the country or state

where you will be using the Croozer Dog.

Before your  rst ride ...

It is vitally important that you familiarize yourself with the

Croozer Dog before you use it for transporting your dog.

You will also need to help your dog get used to the Croozer

Dog. Prior to your  rst trip, Zwei plus zwei GmbH recom-

mends taking a practice ride (without your dog) in a calm,

traf c-free area; load the Trailer with cargo of approximate-

ly the same weight as your dog, for example, by strapping

a loaded backpack into the cabin. This is a great way to

become acquainted with the handling of the bicycle and

the dimensions of the trailer.

Buckle up!

For your safety and the safety of your dog and other road

users, dogs should always be leashed inside the trailer.

Pulling the Croozer Dog as a Bicycle Trailer

Before each ride, check the following:

• Are the wheels securely attached?

• Are both vertical frame tubes snapped securely into the

clips?

• Are all security pins correctly inserted and locked?

Check that none of the security pins are hanging freely

from their straps.

• Check tire pressure prior to each ride. The actual tire

pressure should never be higher or lower than the

maximum and minimum in ation pressures marked

on the tire sidewall. (See also page 22). Never use

compressed air, e.g. from a gas station, to  ll your tires.

The rapid air ow and high pressure can overin ate the

tires, causing the tube and/or tire to burst.

Turning

Always reduce your speed to a walking pace when mak-

ing turns with the Bicycle Trailer. Keep in mind that riding

speed is often underestimated, especially on bikes with

electric assist. When turning at high speeds, the increased

centrifugal force can cause the trailer to skid or tip over

and result in accidents with serious injury or death.

Riding downhill

Always reduce your speed when riding downhill. Riding at

excessive speeds can cause the Trailer to skid, potentially

resulting in accidents with serious injury or death.

CroozerDog14-ENG-USACAN-2-14

Safety Guidelines

Riding over curbs or uneven surfaces

Riding over a curb or other obstacle with only one wheel

of the Bicycle Trailer could cause the Trailer to tip over,

resulting in accidents with serious injury or death. Empty

trailers are especially susceptible to tipping. Therefore, if

you have to ride over a curb or similar obstruction, always

use extreme caution and ride at very low speeds. Never

use the Croozer Dog on stairs or escalators.

Being visible to others

Never use your Croozer Dog as a Bicycle Trailer in road

trafc without the safety ag mounted. The safety ag

makes it easier for other road users to see you.

Carrying cargo

Never transport cargo items together with a dog or other

animal in the Trailer. Never attach cargo, such as bags

or panniers, to the outside of the Trailer. Cargo attached

outside of the Trailer can drastically affect the handling and

stability of the Croozer Dog, potentially resulting in acci-

dents with serious injury or death. Smaller objects, such as

leashes etc., can be stowed in the pockets on the front and

rear panels of the Trailer.

Using the Croozer Dog as a Stroller

The Croozer Dog with Stroller Kit is not approved for jog-

ging or skating. Pushing the Stroller faster than a walking

pace is not permitted.

Use, storage, and transport

Never transport the Croozer Dog – even when folded – on

the roof of a motor vehicle.

Never use or store the Croozer Dog at temperatures below

- 4°F (-20°C).

Assembly, maintenance, and repair

Technical condition

Never use the Croozer Dog if it is not in perfect working

order. The Croozer Dog must be periodically inspected for

damage and/or wear to the wheels, hitch arm, frame, fabric

body, security pins, and axle hitch. If any of these parts are

found to be damaged, the Croozer Dog may not be used

until the damage has been properly repaired, ideally by a

professional bicycle mechanic.

It is critical that all maintenance work specied in the

section “Croozer Dog Inspections and Maintenance” be

performed in the specied intervals.

Using the Croozer Dog when it is not in perfect working

order can result in accidents with serious injury or death.

Proper assembly and repair

The Croozer Dog must be properly assembled. Follow the

instructions for the correct installation of the axle hitch,

hitch arm and Stroller Kit components. When in doubt,

contact your Croozer dealer. All repairs must be carried out

to professional standards using only original Croozer parts,

ideally by a professional bicycle mechanic. Incorrect instal-

lation or repair work could result in accidents with serious

injury or death.

Suitable accessories and original spare parts

Only use accessories and original spare parts that have

been recommended and approved by Zwei plus zwei

GmbH. These are the only components that can be used

safely with the Croozer Dog. When in doubt, consult a

Croozer dealer. The use of non-approved accessories or

incompatible spare parts could result in accidents with

serious injury or death. Zwei plus zwei GmbH cannot be

held responsible for any damage resulting from the use of

non-approved accessories or incompatible spare parts.

Changes and modications

For safety reasons, no modications or changes can be

made to the Croozer Dog.

Do not install attachment parts, such as luggage racks etc.

Making modications or changes to your Croozer Dog can

result in accidents with serious injury or death. Further-

more, changes or modications the vehicle will void any

warranty claims. Zwei plus zwei GmbH will not be liable for

damages of any kind resulting from changes or modica-

tions that have been made to the Croozer Dog.

WARNINGS

Never transport children in the Croozer Dog.

Choking hazard! The shipping box contains small parts

that could present a choking hazard to young children.To

avoid serious injuries or death, keep small parts away from

young children.

Do not use plastic bags or packaging in cribs, beds,

carriages, or playpens. Plastic bags and packaging materi-

als can be dangerous. To avoid danger of suffocation,

keep plastic bags and packaging away from babies and

children. Babies and children could pull plastic bags or

packaging over their heads and suffocate.

It is vitally important to confirm that the towing bicycle is

suitable for pulling trailers. Pulling a trailer with a bicycle

that has not been approved by its manufacturer for use

as a towing bicycle can result in frame breakage or other

material damage. This could cause accidents with serious

injury or death.

Wheels that have not been securely attached can fall

off when riding, resulting in accidents with serious injury

or death. After you have attached the wheels, it is vitally

important that you check whether the axles are securely

locked into the axle receivers by firmly pulling on the

wheels. It should not be possible to remove the wheels

without pressing on the dust cap.

It is very important that you do not confuse the hitch arm

attachment bracket with the handlebar attachment bracket

(marked with a warning label). The handlebar attachment

bracket is not intended for use with the hitch arm. The

use of the Trailer with the hitch arm attached to the wrong

bracket could cause accidents with serious injury or death.

The improper use of the brackets could also damage the

Trailer.

It is vitally important that the hitch be properly installed. An

improperly installed hitch could come loose while riding

and cause accidents with serious injury or death.

The tension-adjusting nut of the towing bicycle must

engage the threads for at least five full turns in order

to ensure adequate clamping force for holding the rear

wheel securely. Failure to tighten the tension-adjusting nut

adequately may result in accidents with serious injury or

death. If the quick-release skewer is too short, it must be

replaced. Consult a professional bicycle mechanic for the

appropriate parts and assistance.

III

CroozerDog14-ENG-USACAN-2-14

Safety Guidelines

ENG

It is vitally important that the rear wheel of the towing

bicycle with the hitch be installed correctly. Riding with

an incorrectly installed rear wheel could result in acci-

dents with serious injury or death. Follow the instructions

and warnings given in the owner’s manual of the towing

bicycle. When in doubt, consult a professional bicycle

mechanic.

When pulling the Croozer Dog as a Bicycle Trailer, the

safety flag must be properly mounted at all times. If the

safety flag is not properly mounted, other road users may

fail to see the Croozer Dog, which could result in accidents

with serious injury or death.

Always check that the wire loop of the security pin is

snapped securely onto the pin end. If the security pin is

not securely locked, the hitch arm could fall off the towing

bicycle while riding, resulting in accidents with serious

injury or death.

Never pull the Croozer Dog as a Trailer without the hitch-

arm safety strap securely fastened to the towing bicycle.

The safety strap ensures that the Trailer would remain

connected to the towing bicycle if the hitch connector were

to fall off the axle hitch. Failure to use the safety strap as

specified above could cause accidents with serious injury

or death.

Never leave the Stroller wheel attached when using the

Croozer Dog as a Trailer. The Stroller wheel could get

caught on obstacles as you pass, resulting in accidents

with serious injury or death.

The rider must wear a CPSC-approved bicycle helmet at

all times. In the case of an accident, a helmet will prevent

or reduce head injuries. In some countries, the use of

helmets is required by law. Riding without a helmet could

result in serious injury or death in the case of an accident.

Riding too fast could cause the trailer to skid or even tip

over, resulting in accidents with serious injury or death.

Never use a trailer without lighting at night, dusk, or dawn

– or whenever visibility is in any way reduced. Other road-

users may not be able to see you, which could result in

accidents with serious injury or death.

Never overload the Croozer Dog. Excessive weight will

have a significant effect on the Croozer Dog’s handling,

which could result in accidents with serious injury or death.

Never use the Croozer Dog if it is not in perfect working

order. Damaged parts could cause accidents with serious

injury or death. Therefore, it is vitally important that you

have your Croozer Dog serviced regularly – at least once a

year – by a professional bicycle mechanic.

It is vitally important that the maintenance work be per-

formed to professional standards and at the specified

intervals.

Inspect the tires periodically for adequate tread depth and

any signs of damage or excessive wear. Worn-out or dam-

aged tires can affect the handling and even burst, which

could result in accidents with serious injury or death.

CAUTIONS

RISK OF PINCHING OR CRUSHING! There are pinch

points between the frame tubes and clips, that may cause

painful injuries. Use caution to avoid these points when

folding or unfolding the trailer.

NOTICES

If the locking mechanisms are not properly engaged, the

frame of the Croozer Dog could collapse while riding, po-

tentially resulting in serious injuries for the dog.

Always check that the wire loop of the Stroller wheel secu-

rity pin is snapped securely onto the pin end. If the security

pin is not securely locked, the Stroller wheel could fall off

while in use, potentially damaging the hitch arm.

After removing the Stroller wheel, be sure to lock the secu-

rity pin back into the hole in the Stroller wheel socket or in

the hitch connector. Never leave the security pin hanging

freely from its strap! It could get caught on passing objects

and be pulled off, damaging the vehicle.

Check that no sharp objects are positioned in such a way

that they could damage the fabric body during transport.

Use packaging material if necessary.

Never transport the Croozer Dog – even when folded – on

the roof of a motor vehicle, as this could damage the fabric

cover.

Check the tire pressure before each use. The actual tire

pressure should never be higher or lower than the maxi-

mum and minimum inflation pressures (1) marked on the

tire sidewall. Riding with under-inflated tires can damage

the tires and rims. Over-inflation can cause the inner tube

or tire to explode. The inner tubes have Schrader valves,

also known as car valves. You will need a pump with the

appropriate nozzle. Never use compressed air, e.g. from a

gas station, to fill your tires. The quick flow and high pres-

sure can overinflate the tires, causing the tube and/or Tire

to burst.

To prevent mildew and mold growth, the Croozer Dog must

be completely dry and clean before being put into storage.

CroozerDog14-ENG-USACAN-2-14

Safety Guidelines

CroozerDog14-ENG-USACAN-2-14

Table of Contents

ENG

Description . . . . . . . . . . . . . . . . .2

What’s what?. . . . . . . . . . . . . . . . . . . . . . 2

2-in-1 System . . . . . . . . . . . . . . . . . . . . . 3

What is the Croozer Dog? . . . . . . . . . . . . . . . 4

How should the Croozer Dog be used? . . . . . . . . 4

How shouldn’t the Croozer Dog be used? . . . . . . . 4

Orientation and wording . . . . . . . . . . . . . . . . 4

Applicable standards . . . . . . . . . . . . . . . . . . 4

Initial Assembly and Unfolding

the Croozer Dog . . . . . . . . . . . . . .5

Checking package contents . . . . . . . . . . . . . . 5

Unfolding the Croozer Dog . . . . . . . . . . . . . . 6

Attaching the mat. . . . . . . . . . . . . . . . . . . . 7

Attaching and removing the wheels . . . . . . . . . . 7

Converting the Croozer Dog to

a Bicycle Trailer . . . . . . . . . . . . . . .8

Installing and removing the hitch arm . . . . . . . . . 8

Installing the axle hitch to the towing bicycle. . . . . . 8

Installing the safety  ag . . . . . . . . . . . . . . . 11

Converting the Croozer Dog to

a Stroller. . . . . . . . . . . . . . . . . . 12

Installing and removing the Stroller wheel . . . . . . 12

Attaching and removing the handlebar. . . . . . . . 13

Using your Croozer Dog . . . . . . . . . 14

Getting your dog used to the Croozer Dog . . . . . 14

Loading, unloading and securing your dog. . . . . . 14

Opening and closing the front window . . . . . . . . 14

Transporting dog and cargo . . . . . . . . . . . . . 15

Hitching the Croozer Dog to the Towing Bicycle . . . 16

Special considerations when riding with

the Bicycle Trailer . . . . . . . . . . . . . . . . . . 17

Special Considerations When Using the Stroller. . . 19

Transporting your Croozer Dog . . . . . 20

Croozer Dog Inspections and

Maintenance. . . . . . . . . . . . . . . . 21

Inspection intervals . . . . . . . . . . . . . . . . . 21

Service intervals . . . . . . . . . . . . . . . . . . . 21

Inspecting the hitch arm, hitch connector

and Stroller Kit components . . . . . . . . . . . . . 22

Inspect the fabric body . . . . . . . . . . . . . . . . 22

Checking tyre pressure and treads. . . . . . . . . . 22

Cleaning and lubricating the wheel axles . . . . . . 23

Servicing the Stroller wheel . . . . . . . . . . . . . 23

Servicing the hitch-connector joint . . . . . . . . . . 23

Inspecting the Croozer Dog after an accident . . . . 23

Cleaning and Storing the Croozer Dog . 24

How do I clean and maintain my Croozer Dog? . . . 24

How do I store my Croozer Dog? . . . . . . . . . . 24

Preparing the Croozer Dog for disposal . . . . . . . 25

Technical Data . . . . . . . . . . . . . . 26

Accessories . . . . . . . . . . . . . . . . 26

Servicing and warranty claims . . . . . 27

Table of Contents

CroozerDog14-ENG-USACAN-2-14

Description

Front pocket

Hitch arm

attachment bracket

Stroller wheel socket

Front re ectors

Stroller wheel

Description

What’s what?

Handlebar

Quick-release wheels

Hitch arm

Spoke re ectors

Safety  ag

Rear pocket

Push button for

quick-release wheels

Rear re ectors

Rear door

Mesh front window

Mesh side windows

Handlebar attachment socket

Hitch connector

Mesh side windows

CroozerDog14-ENG-USACAN-2-14

Description

ENG

2-in-1 System

Croozer Dog Chassis

with hitch arm

Croozer Dog

Bicycle Trailer

ClosedOpen

Croozer Dog

Stroller

Bicycle Kit

Safety  ag,

Axle hitch

Stroller Kit

Handlebar,

Stroller wheel

+ =

Security pins for:

Hitch connector

and

Stroller wheel

CroozerDog14-ENG-USACAN-2-14

Description

What is the Croozer Dog?

The Croozer Dog is a vehicle for transporting dogs and

other small animals. It can also be quickly and easily con-

verted to a dog stroller using a stroller wheel and handle-

bar.

How should the Croozer Dog be used?

The Croozer Dog is intended for private use for transport-

ing dogs or other small animals in daylight hours on roads

and other smooth, well-surfaced paths as a bicycle trailer

or stroller. The instructions and safety guidelines provided

in this manual must be followed at all times. For your

safety and the safety of your dog and other road users,

dogs should always be leashed inside the trailer.

Maximum Weight of Loaded

Trailer

(Trailer + Dog)

121 lbs (55 kg)

Maximum Load*

(Dog)

88 lbs (40 kg)

Hitch-arm Load (Nose Weight) 6.6 - 16.6 lbs (3 - 7.5 kg)

* Weight limits only apply if the hitch-arm load is within the speci-

ed range of 6.6 to 16.6 lbs (3-7.5 kg). See page 15.

When in use as a Bicycle Trailer in poor visibility condi-

tions or at night, dusk, or dawn, the Croozer Dog must

be equipped with a lighting system that complies with the

applicable laws and regulations in the country of use. Any

spare parts used for the Croozer Dog must be approved by

Zwei plus zwei GmbH and properly installed, ideally by a

professional bicycle mechanic. Use only accessories that

are suited for the Croozer Dog and/or have been approved

by Zwei plus zwei GmbH.

How shouldn’t the Croozer Dog be used?

The Croozer Dog may not be used in any manner other

than as specied above. Never transport children in the

Croozer Dog. Never use the Croozer Dog as a cargo trail-

er. Never use the Stroller for jogging or skating. Commer-

cial use, overloading, excessive speeds (of more than 12

mph, or 20 km/h, when in use as Dog Trailer or more than

walking speed when used as Stroller), improper repairs,

and use on unsurfaced roads or paths are not permitted.

Never pull the Croozer Dog with a motorized vehicle,

such as a moped or scooter. This also applies to motor-

ized bicycles with a maximum speed of more than 12 mph

(20 km/h). Do not mount the hitch to a bicycle with a rear-

wheel hub motor, unless this modication (the replacement

of the original axle nut) is approved by the manufacturer of

the bicycle and/or motor. Zwei plus zwei GmbH will not be

liable for any damages resulting from non-compliance with

these requirements.

Orientation and wording

Unless otherwise indicated, the terms right and left in this

manual refer to the passenger’s right or left when seated in

the Croozer Dog, facing forward (i.e. relative to the direc-

tion of travel).

Applicable standards

The following standards were taken into consideration:

EN 15918:2011

CroozerDog14-ENG-USACAN-2-14

Initial Assembly and Unfolding the Croozer Dog

ENG

Initial Assembly and Unfolding the

Croozer Dog

If you have purchased the Croozer Dog from a shop, the

dealer should have installed the axle hitch to the towing

bicycle and sold the vehicle “ready to use”. If you ordered

your Croozer Dog from an online or mail-order catalogue,

we recommend having the initial assembly performed by

a professional bicycle mechanic. Furthermore, dealers are

required to provide the customer with all important informa-

tion on the use of the Croozer Dog. If the initial assembly

has been performed, you can skip the  rst few steps of this

section.

If your Croozer Dog was not assembled prior to sale, then

have the initial assembly performed by a professional bi-

cycle mechanic or follow the assembly instructions below.

No tools are required for the assembly.

The Croozer Dog must be properly assembled. Improper

assembly can result in accidents with serious injury or

death.

Checking package contents

The Croozer Dog is packaged in a box for shipment. In or-

der to minimize package size, the Croozer Dog is shipped

in its folded state (1). All of the removable parts are packed

inside the Trailer.

1. Take the folded Croozer Dog out of the box and re-

move all packaging materials.

2. Open the cabin and remove all individual parts from

inside the Trailer.

These parts include the wheels (2), hitch arm with axle

hitch (3), handlebar (consists of two parts) (4), Stroller

wheel (5), mat (6), safety  ag (7), and this manual (8).

3. Remove all packaging material from the individual

parts and recycle if possible. It is advisable to keep the

box, e.g. for future storage or transport.

Do not use plastic bags or packaging in cribs, beds,

carriages, or playpens. Plastic bags and packaging ma-

terials can be dangerous. To avoid danger of suffocation,

keep plastic bags and packaging away from babies and

children. Babies and children could pull plastic bags or

packaging over their heads and suffocate.

Choking hazard! The shipping box contains small parts

that could present a choking hazard to young children.

To avoid serious injuries or death, keep small parts away

from young children.

4. Remove all transport restraints on the frame of the

Croozer Dog.

Unfold the Croozer Dog completely before installing the

individual parts.

CroozerDog14-ENG-USACAN-2-14

Initial Assembly and Unfolding the Croozer Dog

Unfolding the Croozer Dog

1. Place the folded Trailer on a clean and stable surface.

2. Pull up the two side panels (1).

3. Pull the rear frame tube (2) towards the back and

press it into the clips (3) on both sides until you hear

and feel it snap into place.

4. Pull the front frame tube (4) forwards and press it into

the clips (5) until you hear and feel it snap into place.

RISK OF PINCHING OR CRUSHING! There are pinch

points between the tubes and clips, as well as between

the locking mechanism and frame tube, that may cause

painful injuries. Use caution to avoid these points when

folding or unfolding the trailer.

Tip: A new Croozer Dog will be slightly more difficult to

unfold because the canvas is still stiff.

5. Check that the front and rear frame tubes (2 and 4)

are snapped fully into the clips on both sides (3 and

5) by pulling the two frame tubes inwards with gentle

pressure. There should be no movement in the frame

tubes when you press against them.

If the locking mechanisms are not properly engaged, the

frame of the Croozer Dog could collapse while riding,

potentially resulting in serious injuries for the dog.

6. To fold the Trailer, follow these instructions in the re-

verse order. Open all zippers and pull the frame tubes

out of the clips (3 and 5 on both sides).

CroozerDog14-ENG-USACAN-2-14

Initial Assembly and Unfolding the Croozer Dog

ENG

Attaching the mat

The mat is fastened inside the Trailer with four snap hooks.

It can be easily removed at any time, e.g. for cleaning.

1. Open the zippers on the rear or front of the Croozer

Dog.

2. Lay the mat (1) inside and secure it by connecting the

four snap hooks to the D-rings (2) in the inside corners

of the Croozer Dog.

Attaching and removing the wheels

The wheels of the Croozer Dog are equipped with push-

button axles. By pressing the dust cap (1) on the wheel

hub, the retaining balls (2) will retract within the axle to

permit the attachment or removal of the wheel. The wheels

cannot be attached or removed unless the dust cap is

pressed in.

1. Remove the protective caps (3) from the wheel axles.

It is advisable to keep the protective caps for future

use, e.g. when transporting the Croozer Dog.

2. Use one hand to lift up the back of the Croozer Dog.

3. Press the dust cap (1) of the wheel hub with the mar-

king “PUSH”.

4. Insert the wheel axle (4) into the axle receiver (5) of

the Croozer Dog as far as it will go and release the

dust cap.

5. Check whether the wheel is locked securely into the

axle receiver by pulling  rmly on the wheel without

pressing the dust cap. It should not be possible to

remove the wheel unless the dust cap is pressed.

6. Repeat steps 2-5 to attach the second wheel.

Wheels that have not been securely attached can fall

off when riding, resulting in accidents with serious injury

or death. After you have attached the wheels, it is vitally

important that you check whether the axles are securely

locked into the axle receivers by firmly pulling on the

wheels. It should not be possible to remove the wheels

without pressing on the dust cap.

7. To remove the wheels, follow these instructions in the

reverse order. Press the dust caps (1) and pull the

wheel axles out of the receivers.

CroozerDog14-ENG-USACAN-2-14

Converting the Croozer Dog to a Bicycle Trailer

Converting the Croozer Dog to a

Bicycle Trailer

Installing and removing the hitch arm

The hitch arm is installed on the front left side of the

Croozer Dog (relative to the direction of travel). The front

of the Trailer has white re ectors.

1. Lift the front of the Croozer Dog.

2. Hold the hitch arm with the curvature and the hole (1)

facing outwards, and slide the end into the hitch arm

attachment bracket (2) until you hear and feel it snap

into place.

It is very important that you do not confuse the hitch

arm attachment bracket with the handlebar attachment

bracket (marked with a warning label). The handlebar

attachment bracket is not intended for use with the hitch

arm. The use of the Trailer with the hitch arm attached

to the wrong bracket could cause accidents with serious

injury or death. The improper use of the brackets could

also damage the Trailer.

3. To remove the hitch arm, press the release mecha-

nism (3) and pull the hitch arm out of the bracket.

Installing the axle hitch to the towing bicycle

The hitch assembly is mounted to the left side of the bicy-

cle (relative to the direction of travel) and consists of two

parts: a hitch connector (1) on the hitch arm of the Croozer

Dog and an axle hitch (2), which is mounted to the rear

axle of the towing bicycle.

However, before using a bicycle for pulling the Croozer

Dog, you must  rst check whether it is suitable for use as

a towing bicycle. This information can be obtained from

the bicycle manufacturer, a bicycle shop, or the owner’s

manual of the bicycle.

It is vitally important to confirm that the towing bicycle is

suitable for pulling trailers. Pulling a trailer with a bicycle

that has not been approved by its manufacturer for use

as a towing bicycle can result in frame breakage or other

material damage. This could cause accidents with seri-

ous injury or death.

If you are not completely con dent about your ability to

install the axle hitch correctly, please consult with, or

have the installation performed by, a professional bicycle

mechanic.

It is vitally important that the hitch be properly installed.

An improperly installed hitch could come loose while rid-

ing and cause accidents with serious injury or death.

Click!

CroozerDog14-ENG-USACAN-2-14

Converting the Croozer Dog to a Bicycle Trailer

ENG

Installing the axle hitch to a bicycle with a quick-

release axle

The quick-release lever (1) must be positioned on the right

side of the bicycle (relative to the direction of travel). If the

lever is on the left side, the quick-release assembly must

be removed and reinserted from the right side. Be sure to

follow the applicable instructions in the owner’s manual of

the bicycle and/or consult a professional bicycle mechanic.

1. Disengage the quick-release lever (1) on the rear

wheel of the towing bicycle or loosen the hex bolt

(5 mm), depending on the version. Often, the open

position is indicated on the lever by the word “OPEN”.

In this case, when the word “OPEN” can be seen, the

lever is in the open position.

2. Remove the tension-adjusting nut (2) of the quick-

release assembly by turning the nut counterclockwise.

Use caution: the spring located just beneath the nut is

under tension and could  y off when removing the nut.

3. Fit the axle hitch (3) over the end of the quick-release

skewer by sliding the skewer (with the spring) through

the hole in the hitch.

4. Without removing the spring on the end of the quick-

release skewer, thread the tension-adjusting nut (2)

back onto the skewer. Tighten the tension-adjusting

nut until you feel a slight resistance.

The tension-adjusting nut must engage the threads for at

least five full turns in order to ensure adequate clamping

force for holding the rear wheel securely. Failure to tighten

the tension-adjusting nut adequately may result in accidents

with serious injury or death. If the quick-release skewer is

too short, it must be replaced. Consult a professional bicycle

mechanic for the appropriate parts and assistance.

5. Check that the rear wheel is properly aligned, adjusting

the position if necessary; then close the quick-release

lever (1) or tighten the hex bolt, depending on the ver-

sion. Often, the closed position is indicated on the lever

by the word “CLOSE”. In this case, when the lever side

marked “CLOSE” can be seen, the lever is in the closed

position. If the tension-adjusting nut has been tightened

the proper amount, you will be able to feel the resis-

tance increase when the lever is about halfway closed,

i.e. parallel to the axle. The adjustment is correct if you

can fully close the lever but with considerable force. In

the closed position, the lever should be parallel to the

frame, i.e. it should not stick out to the side.

6. Check whether the quick-release is securely engaged

by trying to rotate the endcap of the mechanism

(where the lever is attached) without opening the lever.

If the endcap is loose enough to rotate, then the

clamping force is inadequate. In this case, open the

lever, and tighten the tension-adjusting nut half a turn

clockwise. Repeat steps 5 and 6.

If it is impossible to push the quick-release lever into

the closed position, then open the lever, and unscrew

the tension-adjusting nut half a turn counterclockwise.

Repeat steps 5 and 6. Keep in mind that the tension-

adjusting nut must engage the threads of the quick-

release skewer for at least  ve full turns.

min. 5 x

CroozerDog14-ENG-USACAN-2-14

Converting the Croozer Dog to a Bicycle Trailer

The tension-adjusting nut must engage the threads for at

least five full turns in order to ensure adequate clamping

force for holding the rear wheel securely. Failure to tighten

the tension-adjusting nut adequately may result in accidents

with serious injury or death. If the quick-release skewer is

too short, it must be replaced. Consult a professional bicycle

mechanic for the appropriate parts and assistance.

7. Hold the rear wheel with both hands, and try to rock it

back and forth to check that the quick-release mecha-

nism is securely fastened. If there is any play in the

wheel, repeat steps 5 and 6.

It is vitally important that the rear wheel with the hitch

be installed correctly. Riding with an incorrectly installed

rear wheel could result in accidents with serious injury or

death. Follow the instructions and warnings given in the

owner’s manual of the towing bicycle. When in doubt,

consult a professional bicycle mechanic.

Installing the axle hitch to a bicycle with a solid axle

1. Remove the nut (1) on the left side of the solid axle by

turning it counterclockwise.

It is vitally important that you leave the existing washer on

the axle. This washer prevents the axle from rotating in

the dropouts. Riding without the axle washer can result in

accidents with serious injury or death.

2. Without removing the retaining washer, place the axle

hitch (3) onto the axle by feeding the end of the axle

through the hole in the hitch.

3. Screw the nut (1) back onto the axle, tightening lightly

at rst.

To ensure adequate clamping force, the axle nut must

be tightened onto the threads of the axle by at least 5 full

turns. If it is not possible to tighten the nut at least 5 full

turns, then the axle is too short, which could allow the

rear wheel or hitch to come loose, resulting in accidents

with serious injury or death.

When in doubt, consult a professional bicycle mechanic!

4. Check that the rear wheel is properly centered, adjust-

ing the position if necessary; then tighten the nut (1)

using the tightening torque specied in the owner’s

manual of the bicycle.

5. Finally, hold the rear wheel with both hands and try to

rock it back and forth to check that the wheel is held

securely in the dropouts.

The rear wheel must be properly attached after the

axle hitch has been installed. Riding with an improperly

installed rear wheel can result in accidents with serious

injury or death. Follow the instructions and warnings

given in the owner’s manual of the towing bicycle. When

in doubt, consult a professional bicycle mechanic.

min. 5 x

CroozerDog14-ENG-USACAN-2-14

Converting the Croozer Dog to a Bicycle Trailer

ENG

Installing the safety ﬂ ag

Never use your trailer without the safety  ag in place. The

safety  ag makes it easier for other road users to see the

Croozer Dog, increasing your safety and the safety of

other road users.

For the attachment of the safety  ag, there is a loop (2)

and a canvas sleeve (3) on the left side of the Croozer

Dog.

1. Assemble the  ag pole (1) by connecting the two sec-

tions of the pole.

2. Slide the  ag pole through the loop (2) and into the

canvas sleeve (3).

When pulling the Croozer Dog as a Bicycle Trailer, the

safety flag must be properly mounted at all times. If the

safety flag is not properly mounted, other road users may

fail to see the Croozer Dog, which could result in acci-

dents with serious injury or death.

CroozerDog14-ENG-USACAN-2-14

Converting the Croozer Dog to a Stroller

Converting the Croozer Dog to a

Stroller

To convert the Croozer Dog to a Stroller, a Stroller wheel is

mounted on the hitch arm, and a handlebar on the rear of

the Croozer Dog.

Installing and removing the Stroller wheel

1. Lift the hitch arm.

2. Open the wire loop of the security pin (1) on the

Stroller wheel socket (3) or the hitch connector, and

remove the security pin (1).

Tip: Apply some silicone spray to the swivel stud of the

Stroller wheel to reduce friction and help the wheel

turn more easily.

3. Insert the Stroller wheel (2) into the Stroller wheel

socket (3) on the hitch arm.

4. Push the security pin (1) through the hole in the

Stroller wheel socket (3).

5. Snap the wire loop (4) of the security pin over the pin

end protruding from the other side of the socket to lock

it into place.

Always check that the wire loop of the security pin is

snapped securely onto the pin end. If the security pin is

not securely locked, the Stroller wheel could fall off while

in use, potentially damaging the hitch arm.

6. To remove the Stroller wheel, follow these steps in the

reverse order.

After removing the Stroller wheel, be sure to lock the

security pin back into the hole in the Stroller wheel socket

(3) or in the hitch connector (5). Never leave the security

pin hanging freely from its strap! It could get caught on

passing objects and be pulled off, damaging the vehicle.

ClosedOpen

CroozerDog14-ENG-USACAN-2-14

Converting the Croozer Dog to a Stroller

ENG

Attaching and removing the handlebar

The handlebar consists of two parts: a curved lower tube

(1) and the push bar (2). The push bar  ts into the lower

tube. The handlebar is installed on the rear right side of the

Croozer Dog (relative to the direction of travel). The rear of

the Trailer has red re ectors.

1. Lift the rear of the Croozer Dog.

2. Hold the curved lower tube (1) with the tube curving

upwards and the hole (3) facing outwards, and slide

the end into the handlebar attachment bracket (4)

(marked with the warning label) until you hear and feel

it snap into place.

3. After the curved lower tube has been securely mount-

ed, press the push button (5) on the push bar (2) and

slide it into the upper end of the curved lower tube (1).

When the push bar is fully inserted, you will be able to

hear and see the second button (6) snap into the hole

(7) in the curved lower tube.

4. Pull the handlebar upwards to check whether it is

securely attached.

5. To remove the handlebar, follow these instructions in

the reverse order. Press the release mechanism (8)

and pull the curved lower tube out of the bracket.

Click!

CroozerDog14-ENG-USACAN-2-14

Using your Croozer Dog

Getting your dog used to the Croozer Dog

Initially, your dog may be afraid of using the Trailer.

Therefore, you should spend some time slowly familiar-

izing your dog to the Croozer Dog. Place the trailer with

its wheels removed in a place that is familiar for your dog

(e.g. in the living room), and hide your dog’s favourite toy

inside, or some small treats etc. Give your dog a few days

to get used to the Croozer Dog. Once your dog seems to

feel comfortable in the Trailer, you can start by taking short

trips with him. On these  rst few rides, be sure to check on

your dog frequently and observe his reactions to the move-

ment of the Trailer.

Loading, unloading, and securing your dog

The Croozer Dog has a rear door that can be zipped fully

open to allow for easy loading and unloading of your dog.

1. Open the zippers (1) of the rear door (2) of the

Croozer Dog and fold it upwards.

2. Help your dog into the cabin of the Croozer Dog.

3. Attach your dog’s leash to one of the D-rings (3) in the

inside corners of the cabin.

Always leash your dog inside the cabin when using the

Croozer Dog as a Bicycle Trailer. Sudden movements

and shifting weight, especially with large dogs, can cause

erratic handling, which can lead to accidents with serious

injury or death.

Always close the rear door of the Bicycle Trailer before

riding! Otherwise, your dog could jump out of the Trailer

while riding, which would put himself and other road

users in danger, and potentially cause accidents with

serious injury or death.

4. When unloading your dog, follow these instructions in

the reverse order.

Opening and closing the front window

To allow your dog to look out from the front of the cabin

when using the Croozer Dog as a Stroller, the front window

can be zipped either halfway open (for large dogs) or fully

open (for small dogs).

1. Open the zippers (4) of the front window (5) of the

Croozer Dog halfway, and drape the window mesh

over the crosspiece (6).

2. Open the zippers (4) of the front window (5) complete-

ly, and roll the window mesh inwards.

3. To close the window, follow these instructions in the

reverse order.

When riding with the Croozer Dog as a Bicycle Trailer,

keep the front window closed at all times to prevent in-

sects, small stones, and other road debris from flying into

the cabin and injuring your dog!

La page charge ...

Croozer Dog 2014-2016 Le manuel du propriétaire

Marque: Croozer

Modèle: Dog 2014-2016

Catégorie: Poussettes

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Croozer Dog 2014-2016 Owner's manual

Croozer Dog 2014-2016 Le manuel du propriétaire

Croozer Dog 2014-2016 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents