Winmate R15IB3S-67A3HB Guide de démarrage rapide

Please read these instructions carefully before using this product, and save this manual for future use.

15” G-WIN Rugged

Full IP67 Panel PC

R15IH3S-67A3(HB)

R15IB3S-67A3(HB)

R15ID3S-67A3(HB

Quick Start Guide

V1.0

For more information on this and

other Winmate products, please

visit our website at:

www.winmate.com

Document Part Number: 9152111I102C

- 2 -

CONTENTS

1 INTRODUCTION - 6 -

1.1 Features - 6 -

1.2 Package Contents - 7 -

1.3 Description of Parts - 9 -

1.4 Physical Buttons and LED Indicators - 10 -

2 GETTING STARTED - 12 -

2.1 Turning on Your Device - 12 -

2.2 How to Enable Watchdog - 13 -

2.3 Turning off Your Device - 15 -

3 Mounting - 16 -

3.1 VESA Mounting - 16 -

3.2 Dash/ Yoke Mounting - 17 -

4 INSTALLATION - 19 -

4.1 Wiring Requirements - 19 -

4.2 Connecting to Other Devices - 20 -

4.3 Connector Description - 21 -

4.3.1 Power Input Connector - 21 -

4.3.2 Ethernet Connector - 22 -

4.3.3 Serial Interface Connector - 23 -

4.3.4 USB 2.0 Connector - 24 -

5 SPECIFICATIONS - 25 -

APPENDIX - 27 -

Appendix A: Cleaning the Monitor - 27 -

Appendix B: Winmate Software Development Kit - 28 -

- 3 -

FCC Statement

This device complies with part 15 FCC rules.

Operation is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received

including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a

class "B" digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at him own expense.

European Union

Electromagnetic Compatibility Directive (2014/30/EU)

 EN55024: 2010/ A1: 2015

o IEC61000-4-2: 2009

o IEC61000-4-3: 2006+A1: 2007+A2: 2010

o IEC61000-4-4: 2012

o IEC61000-4-5: 2014

o IEC61000-4-6: 2014

o IEC61000-4-8: 2010

o IEC61000-4-11: 2004

 EN55032: 2012/AC:2013

 EN61000-3-2:2014

 EN61000-3-3:2013

Low Voltage Directive (2014/35/EU)

 EN 60950-1:2006/A11:2009/A1:2010/A12:2011/

A2:2013

This equipment is in conformity with the requirement of the following EU

legislations and harmonized standards. Product also complies with the

Council directions.

- 4 -

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in

any form or by any means, electronic or mechanical, for any purpose, without the

prior written permission of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their

respective owners.

Disclaimer

Winmate Inc. reserve the right to make changes, without notice, to any product,

including circuits and/or software described or contained in this manual in order

to improve design and/or performance. We assume no responsibility or liability for

the use of the described product(s) conveys no license or title under any patent,

copyright, or masks work rights to these products, and make no representations

or warranties that these products are free from patent, copyright, or mask work

right infringement, unless otherwise specified. Applications that are described in

this manual are for illustration purposes only. We make no representation or

guarantee that such application will be suitable for the specified use without

further testing or modification.

Warranty

Winmate Inc. warranty guarantees that each of its products will be free from

material and workmanship defects for a period of one year from the invoice date.

If the customer discovers a defect, we will, at his/her option, repair or replace the

defective product at no charge to the customer, provide it is returned during the

warranty period of one year, with transportation charges prepaid. The returned

product must be properly packaged in its original packaging to obtain warranty

service. If the serial number and the product shipping data differ by over 30 days,

the in-warranty service will be made according to the shipping date. In the serial

numbers the third and fourth two digits give the year of manufacture, and the fifth

digit means the month (e. g., with A for October, B for November and C for

December).

For example, the serial number 1W14Axxxxxxxx means October of year 2014.

Customer Service

We provide a service guide for any problem by the following steps: First, visit the

website of our distributor to find the update information about the product.

Second, contact with your distributor, sales representative, or our customer

service center for technical support if you need additional assistance.

You may need the following information ready before you call:

 Product serial number

 Software (OS, version, application software, etc.)

 Description of complete problem

 The exact wording of any error messages

In addition, free technical support is available from our engineers every business

day. We are always ready to give advice on application requirements or specific

information on the installation and operation of any of our products.

- 5 -

Safety Information

WARNING! / AVERTISSEMENT!

Always completely disconnect the power cord from your chassis

whenever you work with the hardware. Do not make connections

while the power is on. Sensitive electronic components can be

damaged by sudden power surges. Only experienced electronics

personnel should open the PC chassis.

Toujours débrancher le cordon d’alimentation du chassis lorsque

vous travaillez sur celui-ci. Ne pas brancher de connections

lorsque l’alimentation est présente. Des composantes

électroniques sensibles peuvent être endommagées par des sauts

d’alimentation. Seulement du personnel expérimenté devrait ouvrir

ces chassis.

CAUTION/ATTENTION

Always ground yourself to remove any static charge before

touching the CPU card. Modern electronic devices are very

sensitive to static electric charges. As a safety precaution, use a

grounding wrist strap at all times. Place all electronic components

in a static-dissipative surface or static-shielded bag when they are

not in the chassis.

Toujours verifier votre mise à la terre afin d’éliminer toute charge

statique avant de toucher la carte CPU. Les équipements

électroniques moderns sont très sensibles aux décharges

d’électricité statique. Toujours utiliser un bracelet de mise à la

terre comme précaution. Placer toutes les composantes

électroniques sur une surface conçue pour dissiper les charge, ou

dans un sac anti-statique lorsqu’elles ne sont pas dans le chassis.

- 6 -

1 INTRODUCTION

Congratulations on purchasing Winmate® G-WIN Rugged Full IP67 Panel PC.

Panel PC features 15” panel with sunlight readable screen, fanless cooling

system, low power consumption, WLAN integration, great ability for anti-shock &

vibration. The robust design fits the demands for every harsh environment

applications such as logistics, transportation/ fleet management, heavy vehicles,

utility and also outdoor usage.

1.1 Features

Winmate® 15” G-WIN Full IP67 Panel PC features:

 High Quality 15" Panel, 1024 x 768 resolution, 400 nits

 IP67 Dust/ Water proof design (with VESA mounting)

 Aluminum die-casting housing with anti-corrosion treatments

 Build-in ambient light sensor

 Wide range 9 to 36V DC input with isolation

 Optional 6-60V DC Input, and Optional for Ignition On/Off delay

 5 Wire resistive touch/ anti-reflective protection glass (optional)

 Optional HB/ Sunlight readable with brightness up to 1000 nits

- 7 -

1.2 Package Contents

Carefully remove the box and unpack your device. Please check if all the items

listed below are inside your package. If any of these items are missing or

damaged contact us immediately.

Standard factory shipment list:

Panel PC

Quick Start Guide

(Hardcopy)

Driver CD & SBC User

Manual

Varies by product

specifications

9152111I102C

IH32: 9171111I102S

IB32: 9171111I103I

ID32: 9171111I101M

Power Cable

Serial Interface Cable

LAN Cable

94J003L020K1

94G0103090Q0

94I0080080KF

USB Cable

9480108080Q0

- 8 -

Your package may include optional accessories based on your order:

Mounting Bracket

99KK15A00001

- 9 -

1.3 Description of Parts

Unit: mm

Dimensions: 398 x 308 x 58

№

Description

№

Description

①

LAN (M25 Type)

④

9-36V DC (M25 Type)

②

USB (M25 Type)

⑤

OSD Control Panel

③

RS232 (M25 Type)

- 10 -

1.4 Physical Buttons and LED Indicators

Physical buttons and LED indicators (OSD Control Panel) located on the rear

side of the Panel PC.

- 11 -

Physical Buttons

Icon

Button

Function

Power

Turn ON or turn OFF the Panel PC.

Reset

Clear any pending errors or events and brings a

system to normal condition or an initial state.

Lock / Unlock

Tap this button to lock / unlock the function of

OSD panel.

Auto Dimming/

Manually

Tap the button once to AUTOMATICALLY adjust

brightness mode.

Press the button again to MANUALLY adjust

brightness mode.

Day/ Night Mode

Tap this button to enter DAY MODE.

Tap this button to enter NIGHT MODE to

increase visibility in low-light conditions.

Brightness UP

Increase the brightness of the display screen, or

allows user to navigate items of a single OSD

menu.

Brightness

DOWN

Decrease the brightness of the display screen, or

allows user to navigate items of a single OSD

menu.

LED Adjustment

Adjust the brightness of the LED.

LED Indicators

Indicator

Color

Definition

PWR

Green

Power is ON and the device functions normally.

Orange

Panel PC is suspended.

HDD

Green

HDD is active.

OFF

HDD is inactive.

- 12 -

2 GETTING STARTED

2.1 Turning on Your Device

1. Remove the protective cap of the power connector.

2. Connect power cable to the connector of your device. Make sure the cable

fits to the connector, then tighten the O-ring (by turning clockwise) to

secure the connection.

3. The device will boot automatically when powered on.

- 13 -

2.2 How to Enable Watchdog

To enable Watchdog, you need to download Winmate Watchdog utility. Find

more information on Watchdog in “Watchdog Guide” that you can download from

Winmate Download Center or File Share. Refer to the User Manual for more

details.

To enable watchdog in Watchdog AP follow the instructions below:

1. On the right bottom side of the desktop screen, click triangle button to

show hidden icons.

2. Click icon to open Watchdog utility.

3. In Watchdog utility window set countdown time and periodically feed time,

or disable watchdog.

- 14 -

Example:

Every 10 min watchdog will

monitor the system, in case any

error occurs the system will

restart automatically when the

countdown time reaches 0.

Every 9 min watchdog timer will

be reset to 10 min.

Settings

Description

Watchdog Countdown Time

The system automaticity restarts when this

countdown time reaches zero.

Default: 10 min

Periodically Feed Time

To set a cycle time to automatically reset

watchdog timer.

Default: 9 min

Enable / Disable

Enable or disable watchdog.

Default: Enable

- 15 -

2.3 Turning off Your Device

To shut down your device:

1. Select the Start button ( ) and then select Power > Shut down.

2. Disconnect the power cord from the Panel PC to completely turn off the

device.

To forcibly shut down your device, press and hold for three to five seconds the

power button located on the front OSD control panel.

IMPORTANT:

During forced shut down unsaved data may be lost.

- 16 -

3 Mounting

3.1 VESA Mounting

This device supports VESA Mounting and provides various types of mounting

options to fit any industrial use or vehicle.

Size

VESA Plate

15”

100x100 mm

Mounting Instruction

Use Philips M4x5 screws to fix the desk stand to VESA holes on the back cover

of the device.

*The picture is for demonstration purposes only. VESA Mounting accessories are

not supplied by Winmate.

- 17 -

3.2 Dash/ Yoke Mounting

You can purchase mounting bracket from Winmate as an optional accessory.

Part Number: 99KK15A00001

Mounting instruction:

1. Place the Panel PC on the bracket stand, aiming screw hole for each other.

2. Secure three M5x10 screws to fix the device upon the bracket stand.

3. Secure tightly locking handle to the Panel PC.

- 18 -

4. Loosen the hand-screw adjustment tool, then you can adjust product angle

on the stand. Then screw the product tightly again to secure the stand

position.

Desk Stand Dimensions

- 19 -

4 INSTALLATION

4.1 Wiring Requirements

The following common safety precautions should be observed before installing

any electronic device:

 Strive to use separate, non-intersecting paths to route power and

networking wires. If power wiring and device wiring paths must cross make

sure the wires are perpendicular at the intersection point.

 Keep the wires separated according to interface. The rule of thumb is that

wiring that shares similar electrical characteristics may be bundled

together.

 Do not bundle input wiring with output wiring. Keep them separate.

 When necessary, it is strongly advised that you label wiring to all devices

in the system.

CAUTION

 Do not run signal or communication wiring and power wiring in the same

conduit. To avoid interference, wires with different signal characteristics

(i.e., different interfaces) should be routed separately.

 Be sure to disconnect the power cord before installing and/or wiring your

device.

 Verify the maximum possible current for each wire gauge, especially for

the power cords. Observe all electrical codes dictating the maximum

current allowable for each wire gauge.

 If the current goes above the maximum ratings, the wiring could overheat,

causing serious damage to your equipment.

 Be careful when handling the unit. When the unit is plugged in, the internal

components generate a lot of heat which may leave the outer casing too

hot to touch.

- 20 -

4.2 Connecting to Other Devices

This Panel PC comes with various interfaces located on the bottom panel. All of

these connectors have been shipped with protective caps. To ensure the

waterproof function can work properly, make sure that the protective caps and

have been securely tightened whenever the connectors are not used.

IMPORTANT

Please note that when reinstalling the protective cap, it must be fully tightened to

ensure the unit is properly sealed to meet the IP67 enclosure rating.

La page charge ...

Winmate R15IB3S-67A3HB Guide de démarrage rapide

Ce manuel convient également à

Winmate R15IB3S-67A3HB Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents