RIDGID 300 Power Drive Manuel utilisateur

Marque: RIDGID

Modèle: 300 Power Drive

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

300 Power Drive

• Français – 19

• Castellano – pág. 39

Power Drive Manual

940-600.015.10_REV. D

Table of Contents

Recording Form for Machine Serial Number..............................................................................................................1

Safety Symbols..............................................................................................................................................................2

General Power Tool Safety Warnings

Work Area Safety........................................................................................................................................................2

Electrical Safety ..........................................................................................................................................................2

Personal Safety ..........................................................................................................................................................3

Power Tool Use and Care ..........................................................................................................................................3

Service........................................................................................................................................................................3

Specific Safety Information

Foot Switch Safety......................................................................................................................................................4

Machine Safety ..........................................................................................................................................................4

Description and Specifications, Standard Equipment

Description..................................................................................................................................................................4

Specifications..............................................................................................................................................................4

Standard Equipment ..................................................................................................................................................5

Machine Assembly

Mounting on 1206 Stand ............................................................................................................................................5

Mounting 311A Carriage and Tools ............................................................................................................................6

Machine Inspection ......................................................................................................................................................6

Machine and Work Area Set-Up ..................................................................................................................................7

Operating Instructions Using Hand Tools

Installing Pipe in Power Drive ....................................................................................................................................8

Cutting Pipe with Hand Cutter ....................................................................................................................................8

Reaming Pipe with Hand Reamer ..............................................................................................................................9

Threading Pipe with Hand Threader ..........................................................................................................................9

Removing Pipe from Power Drive ............................................................................................................................10

Operating Instructions Using Carriage-Mounted Power Drive Tools

Installing Pipe In Power Drive ..................................................................................................................................11

Cutting Pipe with No. 360 Cutter ..............................................................................................................................11

Reaming Pipe with No. 341 Reamer ........................................................................................................................11

Threading Pipe with Quick-Opening or Self-Opening Die Head ..............................................................................12

Removing Pipe From The Power Drive ....................................................................................................................13

Installing Dies in Quick-Opening Die Head (R.H. & L.H.) ........................................................................................13

Installing Dies in Self-Opening Die Head (R.H. Only) ..............................................................................................13

Checking Thread Length ..........................................................................................................................................14

Accessories ................................................................................................................................................................14

Hand Tools Recommended for Use with Power Drive ............................................................................................14

Maintenance Instructions

Jaw Inserts................................................................................................................................................................15

Jaw Insert Replacement ..........................................................................................................................................15

Lubrication ................................................................................................................................................................15

Motor Brush Replacement ........................................................................................................................................15

Motor Replacement ..................................................................................................................................................15

Machine Storage ........................................................................................................................................................15

Service and Repair......................................................................................................................................................16

Wiring Diagram ..........................................................................................................................................................17

Wiring Schematics ................................................................................................................................................17-18

Conformity Statement........................................................................................................................Inside Back Cover

Lifetime Warranty ........................................................................................................................................Back Cover

*Original Instructions - English

300 Power Drive

Record Serial Number below and retain product serial number which is located on nameplate.

Serial

No.

Model 300 Complete pictured above including Stand,

Threading Carriage, Tool Tray and Oiler.

300 Power Drive

Power Drives

WARNING!

Read this Operator’s Manual

carefully before using this

tool. Failure to understand

and follow the contents of

this manual may result in

electrical shock, fire and/or

serious personal injury.

• Keep children and bystanders away while operat-

ing a power tool. Distractions can cause you to lose

control.

Electrical Safety

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adap -

ter plugs with earthed (grounded) power tools.

Un modified plugs and matching outlets will reduce

risk of electric shock.

• Avoid body contact with earthed or grounded sur-

faces such as pipes, radiators, ranges and refrig-

erators. There is an increased risk of electrical shock

if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk

of electrical shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

940-600.015.10_REV. D

General Power Tool Safety

Warnings*

WARNING

Read all safety warnings, instructions, illustra-

tions and specications provided with this power

tool. Failure to follow all instructions listed below

may result in electric shock, re and/or serious

injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE!

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work Area Safety

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of flam mable

liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

300 Power Drive

Safety Symbols

In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safe-

ty information. This section is provided to improve understanding of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE indicates information that relates to the protection of property.

NOTICE

DANGER

WARNING

CAUTION

This symbol indicates the risk of machine tipping, caus-

ing striking or crushing injuries.

This symbol indicates the risk of fingers, legs, clothes and

other objects catching and/or wrapping on rotating shafts

causing crushing or striking injuries.

This symbol means read the operator’s manual care-

fully before using the equipment to reduce the risk of

injury. The operator’s manual contains important infor-

mation on the safe and proper operation of the equipment.

This symbol means always wear safety glasses with

side shields or goggles while using this equipment to

reduce the risk of injury.

This symbol indicates the risk of fingers, hands, clothes

and other objects catching on or between gears or other

rotating parts and causing crushing injuries.

This symbol indicates the risk of electrical shock.

This symbol means do not disconnect foot switch to

reduce the risk of injury.

This symbol means do not block foot switch (lock in

ON position) to reduce the risk of injury.

This symbol means do not wear gloves while operating

this machine to reduce the risk of entanglement.

This symbol means always use a foot switch when

using a threading machine/power drive to reduce the risk

of injury.

* The text used in the General Power Tool Safety Warnings section of this manual is verbatim, as required, from the applicable UL/CSA 62841-1 edition standard. This

section contains general safety practices for many different types of power tools. Not every precaution applies to every tool, and some do not apply to this tool.

940-600.015.10_REV. D

moving parts. Damaged or entangled cords increase

the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of elec-

tric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces

the risk of electric shock.

Personal Safety

• Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol, or medication. A mo -

ment of inattention while operating power tools may

result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the OFF-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch

ON invites accidents.

• Remove any adjusting key or wrench before turn-

ing the power tool ON. A wrench or a key left at -

tached to a rotating part of the power tool may result in

personal injury.

• Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of the

power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewel ry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

Power Tool Use And Care

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it is

designed.

• Do not use the power tool if the switch does not

turn it ON and OFF. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/or

remove the battery pack, if detachable, from the

power tool before making any adjustments, chang-

ing accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the pow er tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dif-

ferent from those intended could result in a hazardous

situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

Service

• Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

300 Power Drive

940-600.015.10_REV. D

Specific Safety Information

WARNING

Read this operator’s manual carefully before using

the 300 Power Driver. Failure to understand and fol-

low the contents of this manual may result in elec-

trical shock, fire and/or serious personal injury.

Call the Ridge Tool Company, Technical Service Depart -

ment at (800) 519-3456 if you have any questions.

Foot Switch Safety

Using a power drive or threading machine without a

foot switch increases the risk of serious injury. A

foot switch provides better control by letting you

shut off the motor by removing your foot. If clothing

should become caught in the machine, it will contin-

ue to wind up, pulling you into the machine. Because

the machine has high torque, the clothing itself can

bind around your arm or other body parts with

enough force to crush or break bones.

Machine Safety

• Power Drive is made to thread and cut pipe or

bolt and to power RIDGID roll grooving equip-

ment. Follow instructions on proper use of this

machine. Do not use for other purposes such

as drilling holes or turning winches. Other uses or

modifying this power drive for other applications may

increase the risk of serious injury.

• Secure machine to bench or stand. Support long

heavy pipe with pipe supports. This practice will

prevent tipping.

• Do not wear gloves or loose clothing when oper-

ating machine. Keep sleeves and jackets buttoned.

Do not reach across the machine or pipe. Clothing

can be caught by the pipe or machine resulting in

entanglement and serious injury.

• Operate machine from side with REV/OFF/FOR

switch. Eliminates need to reach over the machine.

• Do not use this machine if the foot switch is bro-

ken or missing. Foot switch is a safety device to

prevent serious injury.

• Keep hands away from rotating pipe and fittings.

Stop the machine before wiping pipe threads or

screwing on fittings. Allow the machine to come to

a complete stop before touching the pipe or ma -

chine chucks. This practice will prevent entangle-

ment and serious injury.

• Do not use this machine to make or break fittings.

This practice is not an intended use of the machine

and can result in serious injury.

• Tighten chuck handwheel and engage rear cen-

tering device on the pipe before turning on the

machine. Prevents oscillation of the pipe.

• Keep covers in place. Do not operate the ma chine

with covers removed. Exposure to moving parts may

result in entanglement and serious injury.

• Lock foot switch when machine is not in use (Fi -

gure 1). Avoids accidental starting.

Figure 1 – Locked Foot Switch

Description, Specifications and

Standard Equipment

Description

The RIDGID

Model 300 Power Drive is an electric motor-

driven machine which centers and chucks pipe, conduit

and rod (bolt stock) and rotates it while threading, cutting

and reaming operations are performed. Forward (clock-

wise) or Reverse (counterclockwise) rotation can be

selected with the FOR/OFF/REV switch and a foot switch

provides ON/OFF control of the motor.

The threading, cutting and reaming operations can be per-

formed by conventional hand tools or tools designed for

mounting on the Power Drive. A manual oiling system is

available to flood the workpiece with thread cutting oil dur-

ing the threading operation. Geared Threaders can also be

used with the Power Drive to thread larger diameter pipe.

The RIDGID Model 300 Power Drive can also be used

as a power source for roll grooving equipment. Designed

to attach to the support arms of the Power Drive, the roll

grooving equipment forms standard roll grooves on a

variety of pipe sizes and materials.

NOTE! Contact a RIDGID distributor or consult the RIDGID

catalog for specifications on roll grooving equip-

ment.

Specifications

Threading Capacity .......Pipe

" through 2"

Bolt

" through 2"

300 Power Drive

WARNING

940-600.015.10_REV. D

Geared Threaders:

Pipe 2

" through 6"

Chuck ............................Speed Grip Chuck with

Replaceable Jaw Inserts

Rear Centering Device....Cam Action Rotates with

Chuck

Operating Speed ............38 RPM or 57 RPM

Motor:

Type ............................Universal

Horsepower.................

Volts ............................120V Single Phase AC

25-60 Hz

(230V Available On Request)

Amps...........................15 Amps (36 RPM)

18 Amps (57 RPM)

Controls .........................FOR/OFF/REV Switch and

ON/OFF Foot Switch

Weight (machine only) ....87 lbs. (39.5 kg)

Figure 2 – No. 300 Power Drive and No. 1206 Stand

Standard Equipment

Power Drive Only:

• 300 Power Drive

Power Drive Complete:

• 300 Power Drive

• 1206 Stand

• 311 Carriage with Lever

• 341 Reamer

• 360 Cutter

• 811A Universal Die Head

• Set

" –

" Universal Alloy Dies

• Set 1" – 2" Universal Alloy Dies

• 4 oz. Can White Sealant w/PTFE

• 418 Oiler

• 1 Gallon Nu-Clear Thread Cutting Oil

• 32 Transporter

Machine Assembly

WARNING

To prevent serious injury, proper assembly of the

Power Drive is required. Failure to mount the

Power Drive to a stable stand or bench may result

in tipping and serious injury. The following proce-

dures should be followed:

Mounting on No. 1206 Stand

1. Set up the 1206 Stand by opening legs and pushing

down on the tray. Legs should be stiff and the stand

should not wobble.

NOTE! The tristand leg stiffness can be increased or

decreased by the following procedure:

• Place stand upside down on a flat surface.

• Unlock tray so legs are loose.

• Locate the set screw on the tray leg support on the

rear leg (Figure 3).

300 Power Drive

Spindle Weight

Catalog Model Speed

No. No. Description RPM Lb. Kg.

41855 300 Only 115V,25-60 Hz 38 94 43.0

75075 300 Only 115V,25-60 Hz 57 94 43.0

41860 300 Only 230V,25-60 Hz 38 94 43.0

75435 300 Only 230V,25-60 Hz 38 94 43.0

15682 300 115V,25-60 Hz 38 212 96.2

Complete 1/2″ – 2″ NPT

15722 300 115V,25-60 Hz 57 212 96.2

Complete 1/2″ – 2″ NPT

Figure 4 – No. 300 Power Drive with 311A Carriage, 360

Cutter, 341 Reamer and Die Head

NOTE! When fully inserted, spring-loaded ball will hold

die head in place.

Machine Inspection

WARNING

To prevent serious injury, inspect your Power

Drive. The following inspection procedures should

be performed on a daily basis:

1. Make sure Power Drive is unplugged and the direc-

tional switch is set to the OFF position (Figure 3).

2. Clean the speed chuck jaws with a wire brush.

3. Inspect the jaw inserts for excessive wear. Refer to the

Maintenance Instructions if they need to be replaced.

NOTE! For plastic and coated work pieces, special jaw

inserts (Part No. 97365) should be used to pre-

vent damaging the workpiece.

4. Make sure the foot switch is present and attached to

the Power Drive (Figure 3).

Do not operate the Power Drive without a

foot switch.

940-600.015.10_REV. D

• Loosen the set screw to make the adjustment. To

increase stiffness, move the tray leg support up

towards the base. To decrease stiffness, move

the tray leg down towards the feet.

• Tighten the set screw (increasing leg stiffness

increases tray tension).

2. Mount power drive on the stand using bolts and wing

nuts (Figure 3).

Figure 3 – 300 Power Drive Mounted on No. 1206 Stand

with 418 Oiler

Mounting 311A Carriage and Tools

1. Inspect the support bars to insure they are forward

and secured by two (2) retaining ring assemblies.

Retaining ring set screws must be tight (Figure 4).

2. Secure eyebolt to the 311A Carriage. Slide lever

arm through the eyebolt assembly and secure to

collar assembly with shoulder bolt (Figure 4).

3. Tighten collar assembly thumb screw into groove

on support bar.

4. Install the 360 Cutter and 341 Reamer by inserting

arm in the slot provided in the carriage and secure

with the drive pin (Figure 4).

5. Install 811A Die Head by inserting die head post

into the mating hole in the carriage.

300 Power Drive

No. 360

Cutter

No. 341

Reamer

No. 311

Carriage

w/Lever

Quick or Self-Opening

Die Head

Set Screw (2)

Collar

Assembly

Thumb

Screw

Shoulder Bolt

Eyebolt Assembly

Lever Arm

Support

Bar (2)

Retaining Ring

Assembly (2)

Left

Support Arm

Right

Support Arm

REV/OFF/FOR

Switch

Chuck Jaw

Handwheel

Set Screw (2)

Retaining

Ring Assy. (2)

No. 1206

Stand

Foot Switch

Wing Nut (4)

Bolt (4)

Pipe

Centering

Device

Rear Leg

Set Screw

WARNING

• Clear path to the electrical outlet that does not

contain any sources of heat or oil, sharp edges or

moving parts that may damage electrical cord.

• Dry place for machine and operator. Do not use

the machine while standing in water.

• Level ground.

2. Clean up the work area prior to setting up any equip-

ment. Always wipe up any oil that may have splashed

or dripped from the machine or oiler to prevent slips

and falls.

3. Set up the Power Drive on a flat, level surface.

• For a Power Drive mounted on a 1206 Stand,

open legs of stand and push down on the tray.

Legs should be stiff and stand should not wobble.

NOTE! To increase or decrease leg stiffness, refer to

instructions on “Mounting On 1206 Stand”.

4.. If the workpiece extends more than four (4) feet

beyond the Power Drive, use one or more pipe stands

to prevent tipping and the oscillation of the pipe.

5. If the workpiece extends beyond the Power Drive, set-

up guards or barricades to create a minimum of

three (3) feet of clearance around the Power Drive

and workpiece. This “safety zone” prevents others

from accidentally contacting the machine or workpiece

and either causing the equipment to tip or becoming

entangled in the rotating parts.

6. If necessary, fill the 418 Oiler with RIDGID Thread

Cutting Oil. Position the oiler under the front of the

Power Drive (Figure 3).

7. Make sure FOR/OFF/REV switch is in the OFF posi-

tion.

8. Position the foot switch so that the operator can

safely control the machine, tools and workpiece. As

shown in Figure 8, it should allow the operator to do

the following:

• Stand facing the directional switch.

• Use the foot switch with his left foot.

• Have convenient access to the directional switch,

tools and chucks without reaching across the

machine.

Machine is designed for one person operation.

9. Plug the Power Drive into the electrical outlet making

sure to position the power cord along the clear path

selected earlier. If the power cord does not reach

the outlet, use an extension cord in good condition.

940-600.015.10_REV. D

5. Inspect the power cord and plug for damage. If the

plug has been modified, is missing the grounding

pin or if the cord is damaged, do not use the Power

Drive until the cord has been replaced.

6. Inspect the Power Drive for any broken, missing,

misaligned or binding parts as well as any other con-

ditions which may affect the safe and normal opera-

tion of the machine. If any of these conditions are pre-

sent, do not use the Power Drive until any problem

has been repaired.

7. Lubricate the Power Drive spindle bearings if neces-

sary according to the Maintenance Instructions.

8. Use tools and accessories that are specifically

designed for your Power Drive and meet the needs of

your application. The correct tools and accessories

allow you to do the job successfully and safely.

Accessories suitable for use with other equipment

may be hazardous when used with this Power Drive.

9. Clean any oil, grease or dirt from all handles and

controls. This reduces the risk of injury due to a tool or

control slipping from your grip.

Inspect the cutting edges of your tools and dies. If

necessary, have them replaced prior to using the

Power Drive. Dull or damaged cutting tools and

dies can lead to binding, tool breakage and poor

quality threads.

10. Clean metal shavings and other debris from the chip

tray of the 418 Oiler. Check the level and quality of the

thread cutting oil. Replace or add oil if necessary.

NOTE! Thread cutting oil lubricates and cools the threads

during the threading operation. A dirty or poor

grade cutting oil can result in poor thread quality.

Machine and Work Area Set-Up

WARNING

To prevent serious injury, proper set-up of the

machine and work area is required. The following

procedures should be followed to set-up the ma -

chine:

1. Locate a work area that has the following:

• Adequate lighting.

• No flammable liquids, vapors or dust that may ignite.

• Grounded electrical outlet.

300 Power Drive

940-600.015.10_REV. D

WARNING

To avoid electrical shock and electrical fires, never use

an extension cord that is damaged or does not meet the

following requirements:

• The cord has a three-prong plug similar to shown

in Electrical Safety section.

• The cord is rated as “W” or “W-A” if being used

outdoors.

• The cord has sufficient wire thickness (14 AWG

below 25'/12 AWG 25' - 50'). If the wire thickness is

too small, the cord may overheat, melting the cord’s

insulation or causing nearby objects to ignite.

To reduce risk of electrical shock, keep all

electrical connections dry and off the ground. Do not

touch plug with wet hands.

10. Check the Power Drive to insure it is operating properly.

• Flip the directional switch to FOR (Forward). Press

and release the foot switch. Check that the Power

Drive rotates in a counterclockwise direction as you

are facing the front chuck. Have the Power Drive

serviced if it rotates in the wrong direction or if the

foot switch does not control its stopping or starting.

• Depress and hold the foot switch. Inspect the mov-

ing parts for misalignment, binding, odd noises or

any other unusual conditions that may affect the safe

and normal operation of the machine. If such con-

ditions are present, have the power drive serviced.

• Flip the directional switch to REV (Reverse). Press

and release the foot switch. Check that the Power

Drive rotates in a clockwise direction as you are fac-

ing the chuck.

• Release the foot switch and flip the directional

switch to OFF.

Operating Instructions

For Using Hand Tools

WARNING

Do not wear gloves or loose clothing when operat-

ing Power Drive. Keep sleeves and jackets but-

toned. Do not reach across the machine or pipe.

Do not use this Power Drive if the foot switch is

broken or missing. Always wear eye protection to

protect eyes from dirt and other foreign objects.

Keep hands away from rotating pipe and fittings.

Stop the machine before wiping pipe threads or

screwing on fittings. Allow the machine to come to

a complete stop before touching the pipe or

machine chucks.

Do not use this machine to “make-on” or “break

off” fittings. This practice is not an intended use of

this Power Drive.

Installing Pipe In Power Drive:

1. Mark the pipe at the desired length if it is being cut

to length.

2. Insert the pipe into the Power Drive so that the end to

be worked or the cutting mark is located about 12

inches to the front of the speed chuck jaws.

3. Insert workpieces less than 2 feet long from the front

of the machine. Insert longer pipes through either end

so that the longer section extends out beyond the rear

of the Power Drive.

To avoid equipment tip-overs, position

the pipe supports under the workpiece.

4. Tighten the rear centering device around the pipe by

using a counterclockwise rotation of the handwheel at

the rear of the Power Drive. This prevents move-

ment of the pipe that can result in poor thread quality.

5. Secure the pipe by using repeated and forceful coun-

terclockwise spins of the speed chuck handwheel

at the front of the Power Drive. This action “hammers”

the jaws tightly around the pipe.

6. Extend both support bars fully beyond the front of

the Power Drive.

Cutting Pipe with Hand Cutter

1. Position the pipe cutter on the workpiece with the

cutter wheels facing up (see “Accessories” section

for pipe cutters recommended for use with this

Power Drive).

2. Align the cutter wheels with the mark on the pipe and

rest the pipe cutter’s body on the left support bar

(Figure 5). Hand-tighten the pipe cutter to the work-

piece using the feedscrew handle while keeping the

cutter wheels aligned with the mark.

3. Assume the correct operating posture (Figure 8).

This will allow you to maintain proper balance and to

safely keep control of the machine and tools.

• Be sure you can quickly remove your foot from

the foot switch.

• Stand facing the directional switch.

• Be sure you have convenient access to directional

switch, tools and chucks.

• Do not reach across the machine or workpiece.

300 Power Drive

WARNING

940-600.015.10_REV. D

4. Flip the directional switch to FOR (Forward).

5. Grasp the pipe cutter’s feedscrew handle with both

hands (Figure 5) and depress and hold down the

foot switch with the left foot.

Figure 5 – Cutting Pipe with Hand Cutter

6. Tighten the feedscrew handle slowly and continu-

ously until the pipe is cut. Do not force the cutter

into the workpiece.

To avoid impact injuries, keep a firm grip on

the pipe cutter and be sure it is resting on the support bar.

If not held firmly or supported, the tool may rotate or fall to

the ground.

7. Release the foot switch and remove your foot from the

housing.

Reaming Pipe with Hand Reamer

To prevent serious injury, do not use self-

feeding spiral reamers with the 300 Power Drive.

1. Flip the directional switch to FOR (Forward).

2. Place the reamer in the end of the pipe (see the

“Accessories” section for reamers recommended for

use with this Power Drive).

3. Assume the correct operating posture.

4. Rest handle on the left support bar (Figure 6) and

hold the reamer handgrip with the right hand. To

avoid pinch point injuries, keep your fingers from

coming between the reamer and the support bar.

5. Firmly grasp the end of the reamer handle with the left

hand, then depress and hold the foot switch down.

6. Push the reamer firmly into the pipe with your right

hand until ream is complete. Keep your hand and arm

away from any rotating parts and use a firm grip on

the handgrip.

7. Release the foot switch and remove your foot from the

housing while holding the reamer with both hands.

Figure 6 – Reaming Pipe with Hand Reamer

8. Remove the reamer from the workpiece once the

Power Drive has stopped rotating.

Threading Pipe with Hand Threader

1. Place the die head of the hand threader on the end of

the pipe (see “Accessories” section for hand thread-

ers recommended for use with this Power Drive).

2. Position the ratchet knob on the hand threader so that

the arrow on the knob points up.

3. Rest the hand threader ratchet handle on the left

support bar (as viewed when facing the front of the

Power Drive – Figure 7).

Figure 7 – Pushing Hand Threader onto Pipe to Engage

Dies

300 Power Drive

Pipe

Cutter

Feed

Screw

Handle

Support

Bar

Straight Hand Reamer

Support Bar

Hand Grip

Handle

WARNING

Hand Threader

Ratchet

Knob

Support Bar

To avoid pinch point injuries, keep your

fingers from coming between the hand threader and the

support bar.

4. Apply RIDGID Thread Cutting Oil to the end of the pipe.

5. Assume the correct operating posture. Check to ensure

directional switch is in the FOR (Forward) position.

6. Hold the die head against the workpiece with the

right hand.

To avoid injury from rotating parts or sharp

surfaces, keep hands and fingers away from anything

other than the outer body of the die head.

Figure 8 – Threading with Hand Threader

7. Depress and hold down the foot switch.

8. Push the die head against the pipe using the palm of

the right hand until the dies engage the workpiece.

Once engaged, the threads will be cut as the dies

pull themselves onto the end of the pipe (Figure 7).

9. Remove the right hand from the area of the die head

and liberally oil the dies while the pipe is threaded

(Figure 8).

To avoid serious injury from rotating parts,

allow adequate clearance between your hand and the

rotating parts while oiling.

10. Release the foot switch and remove your foot from the

housing when the pipe reaches the end of the dies.

940-600.015.10_REV. D

11. Lift the threader handle slightly with the right hand

while sliding the left support bar all the way toward the

rear of the drive.

12. Reverse the ratchet knob. The arrow on the knob

should point down.

13. Lower the threader handle below the height of the left

support bar.

14. Slide the left support bar back to its fully extended

position in front of the Power Drive.

15. Lift and hold the threader handle against the left sup-

port bar.

16. Flip the directional switch to REV (Reverse). Depress

and hold the foot switch down until the threader has

unscrewed itself from the workpiece.

To avoid injury due to falling parts, maintain

a firm grip on the threader as the threader will drop to the

floor if not supported when unthreaded completely.

17. Release the foot switch and remove your foot from the

housing.

18. Set the threader down and, if necessary, wipe oil and

debris off the threads with a rag, taking care not to cut

your hand or fingers on any sharp debris or edges.

19. Check the thread for length and depth (Figure 14).

Removing Pipe from the Power Drive

1. Flip the directional switch to OFF.

2. Use repeated and forceful clockwise spins of the

speed chuck handwheel at the front of the Power

Drive to release the workpiece from the speed chuck

jaws.

3. If necessary, loosen the rear centering device using

a clockwise rotation of the handwheel at the rear of

the Power Drive.

4. Slide the workpiece out of the Power Drive, keeping

a firm grip on the workpiece as it clears the Power

Drive.

To avoid injury from falling parts or equip-

ment tip-overs when handling long workpieces, make

sure that the end farthest from the Power Drive is sup-

ported prior to removal.

5. Clean up any oil spills or splatter on the ground

surrounding the Power Drive.

300 Power Drive

Handle

Hand

Threader

Support

Bar

No. 418

Oiler

Foot Switch

WARNING

940-600.015.10_REV. D

Operating Instructions

for Carriage-Mounted

Power Drive Tools

WARNING

Do not wear gloves or loose clothing when oper-

ating Power Drive. Keep sleeves and jackets but-

toned. Do not reach across the machine or pipe.

Do not use this Power Drive if the foot switch is

broken or missing. Always wear eye protection to

protect eyes from dirt and other foreign objects.

Keep hands away from rotating pipe and fittings.

Stop the machine before wiping pipe threads or

screwing on fittings. Allow the machine to come to

a complete stop before touching the pipe or

machine chucks.

Do not use this machine to “make-on” or “break

off” fittings. This practice is not an intended use of

this Power Drive.

Installing Pipe in Power Drive

1. Check to insure the cutter, reamer and die head is

swung to the rear of the carriage.

2. Mark the pipe at the desired length if it is being cut

to length.

3. Insert the pipe into the Power Drive so that the end

to be worked or the cutting mark is located about 12

inches to the front of the speed chuck jaws.

4. Insert workpieces less than 2 feet long form the

front of the machine. Insert longer pipes through

either end so that the longer section extends out

beyond the rear of the Power Drive.

To avoid equipment tip-overs, position

the pipe supports under the workpiece.

5. Tighten the rear centering device around the pipe by

using a counterclockwise rotation of the handwheel at

the rear of the Power Drive. This prevents movement

of the pipe that can result in poor thread quality.

6. Secure the pipe by using repeated and forceful

counterclockwise spins of the speed chuck hand-

wheel at the front of the Power Drive. This action

“hammers” the jaws tightly around the pipe.

Cutting Pipe with No. 360 Cutter

1. Check to insure the reamer and die head are in

the UP position (Figure 9).

2. Move pipe cutter down onto pipe and move car-

riage with carriage lever to line up cutter wheel with

mark on pipe.

3. Tighten cutter feedscrew handle while keeping the

cutter wheel aligned with the mark.

4. Assume the correct operating posture (Figure 11).

This will allow you to maintain proper bal-

ance and to safely keep control of the machine and tools.

• Be sure you can quickly remove your foot from the

foot switch.

• Stand facing the directional switch.

• Be sure you have convenient access to direc-

tional switch, tools and chucks.

• Do not reach across the machine or workpiece.

5. Flip the directional switch to FOR (Forward).

6. Grasp the pipe cutter’s feed handle with both hands

(Figure 9).

Figure 9 – Cutting Pipe with No. 360 Cutter

7. Depress and hold down the foot switch with the left

foot.

8. Tighten the feedscrew handle slowly and continu-

ously until the pipe is cut. Do not force the cutter into

the workpiece.

9. Release the foot switch and remove your foot from

the housing.

10. Swing pipe cutter back to the UP position.

Reaming Pipe with No. 341 Reamer

1. Move reamer arm down into reaming position (Figure

10).

2. Extend reamer by pressing latch and sliding knob

toward pipe until latch engages.

300 Power Drive

WARNING

Feed Screw

Handle

Carriage

Lever

No. 360 Cutter

940-600.015.10_REV. D

3. Check the directional switch to insure it is in the FOR

(Forward) position. Depress and hold the foot switch

down with the left foot.

4. Position reamer into pipe and complete reaming

by pushing carriage lever with right hand.

5. Retract reamer bar and return reamer to the UP

position.

Figure 10 – Reaming Pipe with No. 341 Reamer

6. Release foot switch and remove your foot from the

housing.

Threading Pipe with Quick-Opening

or Self-Opening Die Head

1. Check to insure the cutter and reamer are to the

rear of the carriage (Figure 11).

2. Lower die head into threading position.

3. Check that the proper size dies are in the die head.

One set of dies is required for each of the following

pipe size ranges: (

"), (

" –

"), (

" –

") and (1"

– 2"). Bolt threading requires a separate set of dies

for each bolt size.

4. Set die head to proper size.

NOTE! Refer to the Section on the No. 811A or No.

815A Die Head for instructions on changing

dies and adjusting for proper size.

5. Quick-Opening 811A Die Head (Figure 12) – Rotate

throwout lever to the CLOSED position.

Self-Opening 815A Die Head (Figure 13) – Push

throwout lever down until the release trigger cocks.

6. Apply RIDGID Thread Cutting Oil to end of the pipe.

7. Assume the correct operating posture.

Figure 11 – Threading Pipe with Quick or Self-Opening

Die Head

8. Check directional switch to insure it is in the FOR

(Forward) position. Depress and hold the foot switch

down with the left foot.

9. Engage dies with pipe using carriage lever and oil

dies with plenty of RIDGID Thread Cutting Oil until

thread is completed.

To avoid serious injury from rotating parts,

allow adequate clearance between your hand and rotat-

ing parts when oiling.

10. Quick-Opening 811A Die Head (Figure 12) – When

thread is completed, raise throwout lever to open

position, retracting dies.

Self-Opening 815A Die Head (Figure 13) – When

die head trigger contacts end of pipe, throwout lever

automatically opens.

11. Release foot switch and remove your foot from the

housing.

12. Move carriage lever away from pipe end and return

die head to the UP position.

13. Check the thread for length and depth (Figure 14).

300 Power Drive

Reamer

Chuck Hand

Wheel

Reamer

Latch

Reamer

Knob

Carriage Lever

Die Head

Carriage

Lever

WARNING

size bar. For bolt threads, align index line with BOLT

line on size bar.

9. Tighten clamp lever.

10. If oversize or undersize threads are required, set the

index line in direction of OVER or UNDER size mark

on size bar.

11. Replace die head in machine.

Figure 12 – Universal Quick-Opening Die Head

Installing Dies in No. 815A Self-Opening

Die Head (Right Hand Only)

NOTE! The No. 815 Self-Opening Die Head (Figure

13) for right hand threads requires four sets of

dies to thread pipe ranging from

" through 2".

One set of dies is required for each of the fol-

lowing pipe size ranges: (

"), (

" –

"), (

"–

") and (1" – 2"). Bolt threading requires a sep-

arate set of dies for each bolt size.

1. With machine unplugged, remove die head. Place

self-opening die head on bench in vertical position.

2. Make sure trigger assembly is released.

3. Loosen clamp lever approximately six turns.

4. Pull lock screw out of slot under size bar so that roll

pin in lock screw will by-pass slot. Position size bar so

that index line on lock screw is all the way to the

end of REMOVE DIES position.

5. Lay head down with numbers up.

6. Remove worn dies from die head.

7. Insert new dies to mark on side of dies. Die numbers

1 through 4 on the dies must agree with those on die

head.

8. Rotate cam plate lever back to lock dies in head.

940-600.015.10_REV. D

Removing Pipe from the Power Drive

1. Flip directional switch to OFF.

2. Use repeated and forceful clockwise spins of the

speed chuck handwheel at the front of the Power

Drive to release the workpiece from the speed

chuck jaws.

3. If necessary, loosen the rear centering device using

a clockwise rotation of the handwheel at the rear of

the Power Drive.

4. Slide the workpiece out of the Power Drive, keeping a

firm grip on the workpiece as it clears the Power Drive.

To avoid injury from falling parts or equip-

ment tip-overs when handling long workpieces, make

sure that the end farthest from the Power Drive is sup-

ported prior to removal.

5. Clean up any spills or splatter on the ground sur-

rounding the Power Drive.

Installing Dies in No. 811A Quick-

Opening Die Head (Right and Left Hand)

NOTE! The No. 811A Universal Die Head (Figure 12) for

right hand threads requires four sets of dies to

thread pipe ranging from

" through 2". One

set of dies is required for each of the following

pipe size ranges: (

"), (

" –

"), (

" –

") and

(1" – 2"). The

" pipe dies are not available for

left hand die head. Bolt threading requires a

separate set of dies for each bolt size. No bolt

dies are available for left hand universal die

heads.

1. With machine unplugged, remove die head. Lay die

head on bench with numbers face up.

2. Flip throwout lever to OPEN position.

3. Loosen clamp lever approximately three turns.

4. Lift tongue of clamp lever washer up and out of

slot under size bar. Slide throwout lever all the way

to end of slot in the OVER direction indicated on size

bar (in direction of CHANGE DIES arrow on rear of

cam plate).

5. Remove dies from die head.

6. Insert new dies to mark on side of dies. Die numbers

1 through 4 on the dies must agree with those on die

head.

7. Slide throwout lever back so that tongue of clamp

lever washer will drop in slot under size bar.

8. Adust die head size bar until the index line on lock

screw or link is aligned with proper size mark on

300 Power Drive

WARNING

Index Line

Link

Throwout

Lever

Washer

Head

Clamp Lever

Size Bar

9.With head in vertical position, rotate cam plate until roll

pin on lock screw can be positioned in slot under

size bar. In this position, dies will lock in die head.

Make sure roll pin points toward end of size bar

marked REMOVE DIES.

10. Adjust die head size bar until index line on lock screw

or links is aligned with proper size mark on size bar.

For bolt threads, align index line with BOLT line on

size bar.

11. Tighten clamp lever.

12. If oversize or undersize threads are required , set the

index line in direction of OVER or UNDER size mark

on size bar.

13. Replace die head in machine.

Figure 13 – No. 815 Self-Opening Die Head

Checking Thread Length

1. Thread is cut to proper length when end of pipe is

flush with edge of dies (Figure 14A).

2. Die Head is adjustable to obtain proper thread diam-

eter. If possible, threads should be checked with a

thread ring gage (Figure 14B). A proper thread is cut

when end of pipe is plus or minus one turn of being

flush with face of ring gage.

940-600.015.10_REV. D

300 Power Drive

Figure 14 – Checking Thread Length

NOTE! If a ring gauge is not available, a fitting can be

used. This fitting should be representative of

those being used on the job. The pipe thread

should be cut to obtain 2 to 3 turns hand tight

engagement with fitting. If pipe thread is not prop-

er diameter the index line should be moved in the

direction of the OVER or UNDER size mark on

size bar. (Refer to Installing Dies in Die Heads).

Accessories

WARNING

Only the following RIDGID products have been

designed to function with the 300 Power Drive.

Other accessories designed for use with other

tools may become hazardous when used on this

Power Drive. To prevent serious injury, use only

the accessories listed below.

Accessories for Power Drive

Hand Tools Recommended for Use with

Power Drive

Threaders:

• 12-R Pipe Threader

• OO-R Pipe Threader

• 11-R Pipe Threader

• OO-RB Bolt Threader

Roll Pin

Index Line

Size Bar

Lock Screw

Throwout

Lever

Clamp

Lever

Trigger

Assembly

Die

Pipe

Die

Pipe

A - Full Width Die Thread

Starting to Cut Thread

Flush

(Basic Size)

One Turn Large

(Maximum Size)

One Turn Small

(Minimum Size)

Thin Ring

Gage

Completed Thread

Die Flush

With End

of Pipe

B - Checking Threads Within Pipe Gage

Model

No. Description

1206 Stand for 300 Power Drive

32 Transporter (for Power Drives and Tri-Stand Vises)

819 Nipple Chuck Complete, 1/2″ – 2″ (12mm – 50 mm)

1452 Clip-On Tool Tray

– Jaw Inserts for Coated Pipe

E-863 LH/RH Reamer Cone

– Gearhead Motor Grease

940-600.015.10_REV. D

300 Power Drive

Cutters:

• No. 1-A and 2-A Cutter

• No. 202 Cutter

Reamers:

• No. 2 and 3 Ratchet Reamers

Contact a RIDGID distributor or consult the Ridge cat-

alog for specifications and catalog numbers.

311A Carriage and Tools as Accessories

Geared Threaders:

• No. 141 2

" – 4" Pipe (NPT or BSPT)

• No. 161 4" – 6" Pipe (NPT or BSPT)

Accessories for Threading by

Close-Coupled Method

Accessories for Threading with Drive Shaft

NOTE! See Ridge Tool catalog for listing of pipe sup-

port, thread cutting oil, die heads and dies.

Maintenance Instructions

WARNING

Make sure machine is unplugged from power

source before performing maintenance or mak-

ing any adjustment.

Jaw Inserts

1. Clean teeth of jaw inserts daily with wire brush.

2. Replace jaw inserts when teeth become worn and

fail to hold pipe or rod.

NOTE! Replace entire set of jaw inserts to insure proper

gripping of the pipe or rod.

Jaw Insert Replacement

Figure 15 – Replacing Jaw Inserts

1. Place screwdriver in insert slot and turn 90 degrees

in either direction.

2. Place insert sideways on locking pin and press down

as far as possible.

3. Hold insert down firmly with screwdriver, turn until

teeth face up.

Lubrication

Proper lubrication is essential to trouble-free operation

and long life of Power Drive.

Grease main shaft bearings every 2 to 6 months depend-

ing upon amount of Power Drive use. Grease fittings are

provided on side base, one at each end of shaft. Use a

good grade of cup grease.

Motor Brush Replacement

1. Check motor brushes every six (6) months and re -

place when worn to less than

inch.

2. If communicator is worn, the outer dimension of the

communicator should be turned and the mica should

be undercut before replacing brushes. This should

only be done by qualified repair personnel.

Motor Replacement

1. Unplug motor receptacle from switch box.

2. Remove two (2) screws (E-891) holding motor.

3. Loosen back screw (E-4548) in body at neck of

motor and lift motor out.

Machine Storage

Motor-driven equipment must be kept

indoors or well covered in rainy weather. Store the

machine in a locked area that is out of reach of children

Model

No. Description

311 Carriage with No. 312 Lever

341 Reamer for No. 311 Carriage

360 Cutter for No. 311 Carriage

811A Universal Quick Opening Die Head Only, Right Hand Only

815A Self-Opening Die Head Only, Right Hand Only

Model Geared Threaders

No. Description

141 161

Pipe Supports

758 Loop X

844 Drive Bar XX

346 Support Arm (2) X

NOTE! If gear case does not have loop hole, use No. 3675

Adapter Bracket instead of No. 758 Loop.

Catalog Model

No. No. Description

61122 840-A Universal Drive Shaft

72037 460 Tristand

42510 92 Adjustable Pipe Support

Screw

Driver

Insert

PRESS

DOWN

Locking

Teeth

To Remove To Replace

WARNING

940-600.015.10_REV. D

300 Power Drive

and people unfamiliar with power drives. This machine

can cause serious injury in the hands of untrained users.

Service and Repair

WARNING

Service and repair work on this Power Drive must be

performed by qualified repair personnel. Power Drive

should be taken to a RIDGID Independent Authorized

Service Center or returned to the factory. All repairs

made by Ridge service facilities are warranted against

defects in material and workmanship.

When servicing the Power Drive, only identical replace-

ment parts should be used. Failure to follow these instruc-

tions may create a risk of electrical shock or other serious

injury.

If you have any questions regarding the service or repair

of this machine, call or write to:

Ridge Tool Company

Technical Service Department

400 Clark Street

Elyria, Ohio 44035-6001

Tel: (800) 519-3456

E-Mail: rtctechservices@emerson.com

For name and address of your nearest Independent

Authorized Service Center, contact the Ridge Tool Com -

pany at (800) 519-3456 or http://www.RIDGID.com

940-600.015.10_REV. D

300 Power Drive

Wiring Diagram (115/230V)

Red

Yellow

Blue

Outlet

Yellow

Red

Blue

Switch

White

Suppressor

(230V Only)

Neutral White

(Blue)

3 Prong Plug

Ground (Earth)

Green (Green/Yellow)

Black (Brown)

Green (Green & Yellow)

White

Black

Black (Brown)

White (Blue)

White

FOR

REV

Green

Foot Switch

1. Brush and Armature Leads may be solid colors

or white with a colored stripe.

2. Wire Colors in parenthesis represent Euro pean

color code. European cord is the same except

for plug.

Wiring Schematic (115/230V)

FOR/REV

Switch

Red

Blue

Yellow

White

Motor

Green/Yellow

Suppressor

(230V Only)

Black

Green

Foot Switch

White

Green (Green/Yellow)

Ground (Earth)

Neutral

White (Blue)

Black (Brown)

NOTE! Colors in parenthesis represent

European color code.

940-600.015.10_REV. D

300 Power Drive

Wiring Schematic (230V) with Line Filter

Red

Blue

Yellow

White

Motor

FOR/REV

Switch

(Green/Yellow)

Red

Black

Filter

Blue

Brown

Foot Switch

Brown

Blue

Green/Yellow Ground (Earth)

Neutral

230V AC

Green

White

Black

NOTE! Colors in parenthesis represent

European color code.

La page charge ...

RIDGID 300 Power Drive Manuel utilisateur

Marque: RIDGID

Modèle: 300 Power Drive

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: RIDGID 300 Power Drive User manual
español: RIDGID 300 Power Drive Manual de usuario

RIDGID 300 Power Drive Manuel utilisateur

RIDGID 300 Power Drive Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents