Mitsubishi Electric GT23 Le manuel du propriétaire

Marque: Mitsubishi Electric

Modèle: GT23

Taper: Le manuel du propriétaire

GT23 General Description

Thank you for purchasing the GOT2000 Series.

GT2310-VTBA

GT2308-VTBA

GT2310-VTBD

GT2308-VTBD

Prior to use, please read both this manual and the

detailed manual thoroughly to fully understand the

product.

MODEL GT23-U-GD-E

Model

code

1D7MI4

IB(NA)-0800503ENG-I(2102)MEE

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant

manuals introduced in this manual carefully and pay full attention to

safety to handle the product correctly.

The precautions given in this manual are concerned with this prod-

uct.

In this manual, the safety precautions are ranked as "WARNING"

and "CAUTION".

Note that the CAUTION level may lead to a serious accident

according to the circumstances.

Always follow the instructions of both levels because they are import-

ant to personal safety.

Please save this manual to make it accessible when required and

always forward it to the end user.

[DESIGN PRECAUTIONS]

Indicates that incorrect handling may cause

hazardous conditions, resulting in death or

severe injury.

Indicates that incorrect handling may cause

hazardous conditions, resulting in medium or

slight personal injury or physical damage.

 Some failures of the GOT, communication unit or cable may keep the outputs

on or off.

Some failures of a touch panel may cause malfunction of the input objects

such as a touch switch.

An external monitoring circuit should be provided to check for output signals

which may lead to a serious accident.

Not doing so can cause an accident due to false output or malfunction.

 Do not use the GOT as the warning device that may cause a serious

accident.

An independent and redundant hardware or mechanical interlock is required

to configure the device that displays and outputs serious warning.

Failure to observe this instruction may result in an accident due to incorrect

output or malfunction.

 The GOT backlight failure disables the operation on the touch switch(s).

When the GOT backlight has a failure, the POWER LED blinks (orange/blue)

and the display section dims. In such a case, the input by the touch switch(s)

is disabled.

 The display section of the GOT is an analog-resistive type touch panel.

Do not touch two points or more simultaneously on the display section.

Doing so may cause a touch switch near the touched points to operate

unexpectedly, or may cause an accident due to an incorrect output or

malfunction.

 When programs or parameters of the controller (such as a PLC) that is

monitored by the GOT are changed, be sure to reset the GOT, or turn on the

unit again after shutting off the power as soon as possible.

Not doing so can cause an accident due to false output or malfunction.

 If a communication fault (including cable disconnection) occurs during

monitoring on the GOT, communication between the GOT and PLC CPU is

suspended and the GOT becomes inoperative.

A system where the GOT is used should be configured to perform any

significant operation to the system by using the switches of a device other

than the GOT on the assumption that a GOT communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

WARNING

CAUTION

WARNING

[DESIGN PRECAUTIONS]

[MOUNTING PRECAUTIONS]

[WIRING PRECAUTIONS]

 To maintain the security (confidentiality, integrity, and availability) of the GOT

and the system against unauthorized access, DoS

attacks, computer

viruses, and other cyberattacks from unreliable networks and devices via

network, take appropriate measures such as firewalls, virtual private

networks (VPNs), and antivirus solutions.

Mitsubishi Electric shall have no responsibility or liability for any problems

involving GOT trouble and system trouble by unauthorized access, DoS

attacks, computer viruses, and other cyberattacks.

*1 DoS: A denial-of-service (DoS) attack disrupts services by overloading

systems or exploiting vulnerabilities, resulting in a denial-of-service (DoS)

state.

 Do not bundle the control and communication cables with main-circuit, power

or other wiring.

Run the above cables separately from such wiring and keep them a minimum

of 100mm apart.

Not doing so noise can cause a malfunction.

 Do not press the GOT display section with a pointed material as a pen or

driver.

Doing so can result in a damage or failure of the display section.

 When the GOT is connected to the Ethernet network, the available IP

address is restricted according to the system configuration.

When a GOT2000 series model and a GOT1000 series model are on an

Ethernet network, do not set the IP address 192.168.0.18 for the GOTs and

the controllers on this network.

Doing so can cause IP address duplication at the GOT startup, adversely

affecting the communication of the device with the IP address 192.168.0.18.

The operation at the IP address duplication depends on the devices and the

system.

 Turn on the controllers and the network devices to be ready for

communication before they communicate with the GOT.

Failure to do so can cause a communication error on the GOT.

 When the GOT is subject to shock or vibration, or some colors appear on the

screen of the GOT, the screen of the GOT might flicker.

 Be sure to shut off all phases of the external power supply used by the

system before mounting or removing the GOT main unit to/from the panel.

Not doing so can cause the unit to fail or malfunction.

 Use the GOT in the environment that satisfies the general specifications

described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product

damage or deterioration.

 When mounting the GOT to the control panel, tighten the mounting screws in

the specified torque range (0.36 N•m to 0.48 N•m) with a Phillips-head

screwdriver No.2.

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the

damage of the screws or the GOT.

 Remove the protective film of the GOT.

When the user continues using the GOT with the protective film, the film may

not be removed.

 Operate and store the GOT in environments without direct sunlight, high

temperature, dust, humidity, and vibrations.

 When using the GOT in the environment of oil or chemicals, use the

protective cover for oil.Failure to do so may cause failure or malfunction due

to the oil or chemical entering into the GOT.

 Be sure to shut off all phases of the external power supply used by the

system before wiring.

Failure to do so may result in an electric shock, product damage or

malfunctions.

 Make sure to ground the FG terminal and LG terminal of the GOT power

supply section to the protective ground conductors dedicated to the GOT with

a ground resistance of 100 Ω or less.

 When tightening the terminal screws, use a Phillips-head screwdriver No.2.

 Terminal screws which are not to be used must be tightened always at torque

0.5 N•m to 0.8 N•m.

Otherwise there will be a danger of short circuit against the solderless

terminals.

 Use applicable solderless terminals and tighten them with the specified

torque.

If any solderless spade terminal is used, it may be disconnected

when the terminal screw comes loose, resulting in failure.

WARNING

CAUTION

WARNING

CAUTION

WARNING

CAUTION

[WIRING PRECAUTIONS]

[TEST OPERATION PRECAUTIONS]

[STARTUP/MAINTENANCE PRECAUTIONS]

 Correctly wire the GOT power supply section after confirming the rated

voltage and terminal arrangement of the product.

Not doing so can cause a fire or failure.

 Tighten the terminal screws of the GOT power supply section in the specified

torque range (0.5 N•m to 0.8 N•m). Undertightening can cause a short circuit

or malfunction.Overtightening can cause a short circuit or malfunction due to

the damage of the screws or the GOT.

 Exercise care to avoid foreign matter such as chips and wire offcuts entering

the GOT. Not doing so can cause a fire, failure or malfunction.

 Plug the communication cable into the GOT interface or the connector of the

connected unit, and tighten the mounting screws and the terminal screws in

the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of

the screws or unit.

 Before performing the test operations of the user creation monitor screen

(such as turning ON or OFF bit device, changing the word device current

value, changing the settings or current values of the timer or counter, and

changing the buffer memory current value), read through the manual

carefully and make yourself familiar with the operation method.

During test operation, never change the data of the devices which are used to

perform significant operation for the system.

False output or malfunction can cause an accident.

 When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfunction.

 Correctly connect the battery connector.

Do not charge, disassemble, heat, short-circuit, solder, or throw the battery

into the fire.

Doing so will cause the battery to produce heat, explode, or ignite, resulting in

injury and fire.

 Before starting cleaning or terminal screw retightening, always switch off the

power externally in all phases.

Not switching the power off in all phases can cause a unit failure or

malfunction.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of

the screws or unit.

 Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

 Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

 The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling,

motion or accidental pulling of the cables or can cause a malfunction due to a

cable connection fault.

 When unplugging the cable connected to the unit, do not hold and pull from

the cable portion.

Doing so can cause the unit or cable to be damaged or can cause a

malfunction due to a cable connection fault.

 Do not drop the module or subject it to strong shock. A module damage may

result.

 Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the

battery.

If the battery is dropped or given an impact, dispose of it without using.

 Before touching the unit, always touch grounded metals, etc. to discharge

static electricity from human body, etc.

Not doing so can cause the unit to fail or malfunction.

 Use the battery manufactured by Mitsubishi Electric Corporation.

Use of other batteries may cause a risk of fire or explosion.

 Dispose of used battery promptly.

Keep away from children.Do not disassemble and do not dispose of in fire.

 Be sure to shut off all phases of the external power supply before replacing

the battery or using the dip switch of the terminating resistor.

Not doing so can cause the unit to fail or malfunction by static electricity.

CAUTION

WARNING

CAUTION

[TOUCH PANEL PRECAUTIONS]

[PRECAUTIONS WHEN THE DATA STORAGE IS IN

USE]

[DISPOSAL PRECAUTIONS]

[TRANSPORTATION PRECAUTIONS]

 For the analog-resistive film type touch panels, normally the adjustment is not

required.

However, the difference between a touched position and the object position

may occur as the period of use elapses.

When any difference between a touched position and the object position

occurs, execute the touch panel calibration.

 When any difference between a touched position and the object position

occurs, other object may be activated.

This may cause an unexpected operation due to incorrect output or

malfunction.

 If the SD card mounted on drive A of the GOT is removed while the GOT is

accessed, processing for the GOT might be interrupted about for 20

seconds.The GOT cannot be operated during this period. The functions that

run in the background including a screen updating, alarm, logging, scripts,

and others are also interrupted.Since this interruption makes an impact to the

system operation, it might cause failure.After checking the light off of SD card

access LED, remove the SD card.

 If the data storage mounted on the GOT is removed while the GOT is

accessed, the data storage and files are damaged.To remove the data

storage from the GOT, check that the access to the data storage in SD card

access LED, the system signal, and others is not performed.

 Turning off the GOT while it accesses the SD card results in damage to the

SD card and files.

 When inserting a SD card into the GOT, make sure to close the SD card

cover. Failure to do so causes the data not to be read or written.

 When removing the SD card from the GOT, make sure to support the SD card

by hand as it may pop out.Failure to do so may cause the SD card to drop

from the GOT, resulting in a failure or break.

 When inserting a USB device into a USB interface of the GOT, make sure to

insert the device into the interface firmly.Failure to do so may cause the USB

device to drop from the GOT, resulting in a failure or break

 Before removing the USB device from the GOT, follow the procedure for

removal on the utility screen of the GOT. After the successful completion

dialog is displayed, remove the USB device by hand carefully.Failure to do so

may cause the USB device to drop from the GOT, resulting in a failure or

break.

 When disposing of this product, treat it as industrial waste.

When disposing of batteries, separate them from other wastes according to

the local regulations.

(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the

battery directive in the EU member states.)

 When transporting lithium batteries, make sure to treat them based on the

transport regulations.

(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the

regulated models.)

 Make sure to transport the GOT main unit and/or relevant unit(s) in the

manner they will not be exposed to the impact exceeding the impact

resistance described in the general specifications of this manual, as they are

precision devices.

Failure to do so may cause the unit to fail.

Check if the unit operates correctly after transportation.

 When fumigants that contain halogen materials such as fluorine, chlorine,

bromine, and iodine are used for disinfecting and protecting wooden

packaging from insects, they cause malfunction when entering our products.

Please take necessary precautions to ensure that remaining materials from

fumigant do not enter our products, or treat packaging with methods other

than fumigation (heat method).

Additionally, disinfect and protect wood from insects before packing products.

CAUTION

WARNING

CAUTION

Manual

The following shows the manuals relevant to this product.

For detailed manuals and relevant manuals, refer to the e-Manual or PDF

manuals stored in the DVD-ROM for the screen design software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global

Website (www.MitsubishiElectric.com/fa).

Compliance with the new China RoHS directive

GOT 相关的基于 “ 电器电子产品有害物质限制使用管理办法 ” 要求的表示方法

Note: This symbol mark is for China only.

含有有害 6 物质的名称、含有量、含有部件

本产品中所含有的有害 6 物质的名称、含有量、含有部件如下表所示。

产品中有害物质的名称及含量

本表格依据 SJ/T11364 的规定编制。

○ : 表示该有害物质在该部件所有均质材料中的含量均在 GB/T26572 规定的限量

要求以下。

× : 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572 规定

的限量要求。

Referenced Standard: GB/T15969.2

(Requirement of Chinese standardized law)

Before using the GOT

Connect the connector of the GOT to the connector of the battery (GT11-50BAT,

sold separately).

Refer to the GOT2000 Series User’s Manual (Hardware) for the connection

instructions.

For details on the GOT specifications, installing instructions, wiring, maintenance

and inspection, or checking procedure for the version and the compatible standard,

refer to the GOT2000 Series User’s Manual (Hardware).

Packing List

The GOT product package includes the following:

1. FEATURES

(1) Abundant standard equipment

• Variety of connection with FA devices

• SD card interface compatible with the SDHC card having a

large capacity and allowing high-speed communication

• Connection with various peripheral devices with the USB host

(2) Improved usability

• Abundant troubleshooting

• Easy and clear screen creation

• PC-like operation screen

(3) Enhanced compatibility with Mitsubishi Electric FA devices

(4) Easy replacement

(5) LED backlight

Manual name

Manual number

(Model code)

GOT2000 Series User’s Manual

(Hardware)

SH-081194ENG(1D7MJ5)

GOT2000 Series User’s Manual

(Utility)

SH-081195ENG(1D7MJ6)

部件名称

有害物质

铅

（Pb）

汞

（Hg）

镉

（Cd）

六价铬

（Cr(VI)）

多溴联苯

（PBB）

多溴二苯醚

（PBDE）

电路板组件 × ○ ○ ○ ○ ○

树脂壳体、电缆、膜材 ○ ○ ○ ○ ○ ○

钣金部件、螺丝等金属部件 × ○ ○ ○ ○ ○

Description Quantity

GT23 1

Installation fitting 4

GT23 General Description (This manual) 1

GT23 本体概要说明书

2. PART NAMES AND SETTINGS

The following shows the part names for GT2310 and GT2308.

No. Name Description

1) Display screen Displays the utility and the user-created screen.

2) Touch Pane

For operating the touch switches in the utility and the user-

created screen

3) POWER LED

Lit in blue : Power is properly supplied.

Lit in orange : Screen saving

Blinks in orange/blue : Backlight failure

Not lit : Power is not supplied

4) Unit installation fitting Mounting fixtures for fixing the GOT to the control panel

5) Installation switch Used for OS installations at the GOT startup

6) SD card access LED

Lit: SD card mounted

Blinking: SC card accessed

No lit: SD card not mounted or SD card mounted

(removable)

7) SD card interface For installing a SD card

8) SD card cover

With a switching function for accepting and stopping the

access to the SD card

When the cover is opened : Access is prohibited

When the cover is closed : Access is allowed

9) USB interface (Host)

For connecting a USB mouse, connecting a USB keyboard,

data transfer, and data storage

(connector type: TYPE-A)

10) USB interface (Device)

For connecting a personal computer (connector type: Mini-

11)

Hole for attaching a

cable clamp

Hole for attaching a cable clamp for preventing USB cable

from being pulled out

(Recommended product: RSG-130-V0 made by

KITAGAWA INDUSTRIES CO.,LTD)

12)

Terminating resistor

setting switch

(Inside cover)

For switching on and off of the terminating resistor for the

RS-422 and RS-485 communication port (Default (Off))

13) Battery holder Houses the battery

14) Power terminal Power input terminal, LG terminal, FG terminal

15) Ethernet interface

For communicating with a controller or connecting a

personal computer (connector type: RJ-45 (modular jack))

16) RS-232 interface

For communicating with a controller (Connector type: D sub

9-pin (male))

17) RS-422/485 interface

For communicating with a controller (Connector type: D sub

9-pin (female))

Example:GT2310

1)2)

10)

17) 16)15) 14)

4) 13) 4)

4) 4)

12)

11)

3. SPECIFICATIONS

3.1 General Specifications

*1: The operating ambient temperature indicates the temperature inside the

enclosure of the control panel to which the GOT is installed.

La température ambiante de fonctionnement indique la température à l'intérieur

du boîtier du tableau de commande sur lequel le GOT est installé.

*2: If ambient temperature exceeds 40 , do not exceed absolute humidity

40 90%.

Si la température ambiante dépasse 40 , ne dépassez pas l'humidité absolue

de 40 90%.

*3: Do not use or store the GOT under pressure higher than the atmospheric

pressure of altitude 0m (0ft.).

Failure to observe this instruction may cause a malfunction.

When an air purge is made inside the control panel by adding pressure, there

may be a clearance between the surface sheet and the screen making it difficult

to use the touch panel, or the sheet may come off.

*4: This indicates the section of the power supply to which the equipment is

assumed to be connected between the public electrical power distribution

network and the machinery within the premises.

Category II applies to equipment for which electrical power is supplied from

fixed facilities.

The surge voltage withstand level for up to the rated voltage of 300 V is 2500 V.

*5: This index indicates the degree to which conductive material is generated in the

environment where the equipment is used.

In pollution degree 2, only non-conductive pollution occurs but temporary

conductivity may be produced due to condensation.

*6: When a protective cover for oil is mounted on the GOT, the maximum operating

ambient temperature must be 5°C lower than the one described above.

Lors de l'installation du couvercle de protection contre l’huile, la température

ambiante de fonctionnement doit être réduite de 5°C par rapport aux valeurs

maximales dans les spécifications générales.

3.2 Power Supply Specifications

The following indicates the power supply specifications for GT23.

Item Specifications

Operating ambient

temperature

Température

ambiante de

fonctionnement

0 to 55

*2 *6

0 à 55

*2 *6

Storage ambient

temperature

-20 to 60

Operating ambient

humidity

10 to 90% RH, non-condensing

Storage ambient

humidity

10 to 90% RH, non-condensing

Vibration resistance

Compliant

with JIS B

3502 and

IEC

61131-2

Frequency Acceleration

Half-

amplitude

Sweep

count

Under

intermittent

vibration

5 to 8.4Hz

3.5mm

10 times

each in X,

Y and Z

directions

8.4

to150Hz

9.8m/s

Under

continuous

vibration

5 to 8.4Hz

1.75mm

8.4

to 150Hz

4.9m/s

Shock resistance

Compliant with JIS B 3502 and IEC 61131-2 (147 m/s

(15G), 3 times

each in X, Y and Z directions)

Operating

atmosphere

No greasy fumes, corrosive gas, flammable gas, excessive

conductive dust, and direct sunlight (Same as storage atmosphere)

Operating altitude

2000 m (6562 ft) max.

Installation location Inside control panel

Overvoltage

category

II or less

Pollution degree

2 or less

Cooling method Self-cooling

Grounding

Grounding with a ground resistance of 100 Ω or less by using a ground

cable that has a cross-sectional area of 2 mm

or more.

If impossible, connect the ground cable to the control panel.

Point

Refer to the GOT2000 Series User’s Manual (Hardware) for details on the performance

specifications of each GOT.

Note

Operation at momentary failure

• If an instantaneous power failure occurs in the power supply and continues for more

than the permissible period, the GOT will be reset.

• Make sure to power on the unit more than 5 seconds after power-off.

3.2.1 For GOTs powered from the 100 to 240VAC

power supply

3.2.2 For GOTs powered from the 24VDC power

supply

3.3 External Dimensions

Item

Specifications

GT2310-VTBA GT2308-VTBA

Power supply voltage AC100 to 240VAC (+10%, -15%)

Power frequency 50,60Hz 5%

Input max. apparent power 44VA (maximum load) 30VA (maximum load)

Power

consum

ption

maximum load 18W or less 11W or less

Stand alone 15W 9W

Stand alone with backlight

off

8W 6W

Inrush current

40A or less (4ms, operating ambient temperature

25 , maximum load)

Allowable momentary power failure

time

20 ms or less (100VAC or more)

Noise immunity

1,500Vp-p noise voltage, 1 s noise width (when

measuring with a noise simulator under 25 to 60Hz

noise frequency)

Dielectric withstand voltage

1500VAC for 1 minute across power terminals and

earth

Insulation resistance

10M or more across power terminals and earth by a

500V DC insulation resistance tester

Applicable wire size 0.75[mm

] to 2[mm

]

Applicable solderless terminal

Solderless terminal for M3 screw RAV1.25-3, V2-

S3.3, V2-N3A, FV2-N3A

Applicable tightening torque

(Terminal block terminal screw)

0.5[N•m] to 0.8[N•m]

Item

Specifications

GT2310-VTBD GT2308-VTBD

Power supply voltage DC24V (+25%, -20%)

Power

consu

mption

Maximum load 16W or less 11W or less

Stand alone 13W 8W

Stand alone with backlight

off

7W 6W

Inrush current

40A or less (2ms, operating ambient temperature

25 , maximum load)

Allowable momentary power failure

time

10 ms or less

Noise immunity

500Vp-p noise voltage, 1 s noise width (when

measuring with a noise simulator under 25 to 60Hz

noise frequency)

Dielectric withstand voltage

350VAC for 1 minute across power terminals and

earth

Insulation resistance

10M or more across power terminals and earth by a

500V DC insulation resistance tester

Applicable wire size 0.75[mm

] to 2[mm

]

Applicable solderless terminal

Solderless terminal for M3 screw RAV1.25-3, V2-

S3.3, V2-N3A, FV2-N3A

Applicable tightening torque

(Terminal block terminal screw)

0.5[N•m] to 0.8[N•m]

199 (7.84)

(0.39)

303 (11.93)

208 (8.19)

228 (8.98)

288 (11.34)

218 (8.58)

56 (2.20)

(0.24)

GT2310 GT2308

175 (6.89)

194 (7.64)

(0.39)

241 (9.49)

166 (6.54)

226 (8.90)

56 (2.20)

(0.24)

Unit : mm (inch)

4. EMC AND LOW VOLTAGE DIRECTIVE

For the products sold in European countries, the conformance to the EMC

Directive, which is one of the European Directives, has been a legal

obligation since 1996. Also, conformance to the Low Voltage.

Directive, another European Directives, has been a legal obligation since

1997.

Manufacturers who recognize their products must conform to the EMC and

Low Voltage Directive are required to declare that their products conform to

these Directives and put a "CE mark" on their products.

• Authorized representative in Europe

Authorized representative in Europe is shown below.

Name :Mitsubishi Electric Europe BV

Address :Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany

4.1 Requirements to Meet EMC Directive

EMC Directives are those which require "any strong electromagnetic force

is not output to the external.:Emission (electromagnetic interference)" and

"It is not influenced by the electromagnetic wave from the external.:

Immunity (electromagnetic sensitivity)".

Items4.1.1 through4.1.3 summarize the precautions to use GOT and

configure the mechanical unit in order to match the EMC directives.

Though the data described herein are produced with our best on the basis

of the requirement items and standards of the restrictions gathered by

Mitsubishi Electric, they do not completely guaranteed that all mechanical

unit manufactured according to the data do not always match the above.

4.1.1 EMC directive

The standards of the EMC Directive are shown below.

*1: The GOT is an open type device (device installed to another device) and must

be installed in a conductive control panel.

The above test items are conducted in the condition where the GOT is installed

on the conductive control panel and combined with the Mitsubishi Electric PLC.

*2: QP (Quasi-Peak): Quasi-peak value, Mean: Average value

Applied

standard

Test standard Test details Standard value

EN61131-2

: 2007

CISPR16-2-3

Radiated noise

Electromagnetic

emissions from the

product are

measured.

30M-230MHz QP:

30dB V/m (30m in

measurement range)

*2, *3

230M-1000MHz QP:

37dB V/m(30m in

measurement range)

*2, *3

CISPR16-2-1

Conducted noise

Electromagnetic

emissions from the

product to the power

line is measured.

150k-500kHz QP:79dB,

Mean: 66dB

500k-30MHz QP:73dB,

Mean: 60dB

IEC61000-4-2

Electrostatic

immunity

Immunity test in

which static

electricity is applied

to the cabinet of the

equipment.

4kV Contact discharge

8kV Aerial discharge

IEC61000-4-3

Radiated

electromagnetic

field AM modulation

Immunity test in

which field is

irradiated to the

product.

80-1000MHz:10V/m

1.4-2GHz:3V/m

2.0-2.7GHz:1V/m

80%AM modulation@1kHz

IEC61000-4-4

Fast transient burst

noise

Immunity test in

which burst noise is

applied to the power

line and signal lines.

Power cable: 2kV

Digital I/O: 1kV

Analog I/O: 1kV

Signal cable: 1kV

IEC61000-4-5

Surge immunity

Immunity test in

which lightening

surge is applied to

the product.

AC power type

Power line (between line and

ground): 2kV

Power line (between lines)

: 1kV

Data communication port

: 1kV

DC power type

Power line (between line and

ground) : 0.5kV

Power line (between lines)

: 0.5kV

Data communication port

: 1kV

IEC61000-4-6

Conducted RF

immunity

Immunity test in

which a noise

inducted on the

power and signal

lines is applied.

Power line: 10V

Data communication port: 10V

IEC61000-4-8

Power supply

frequency magnetic

field immunity

Test for checking

normal operations

under the

circumstance

exposed to the

ferromagnetic field

noise of the power

supply frequency

(50/60Hz).

30 A/m

IEC61000-4-11

Instantaneous

power failure and

voltage dips

immunity

Test for checking

normal operations

at instantaneous

power failure.

AC power type

0.5 cycle 0% (interval 1 to 10s)

250/300 cycle 0%

10/12 cycle 40%

25/30 cycle 70%

*3: The above test items are conducted in the following conditions.

30M-230MHz QP : 40dB V/m (10m in measurement range)

230M-1000MHz QP : 47dB V/m (10m in measurement range)

4.1.2 Control panel

The GOT is an open type device (device installed to another device) and

must be installed in a conductive control panel.

It not only assure the safety but also has a large effect to shut down the

noise generated from GOT, on the control panel.

(1) Control Panel

(a) The control panel must be conductive.

(b) When fixing a top or bottom plate of the control panel with bolts,

do not coat the plate and bolt surfaces so that they will come into

contact.

And connect the door and box using a thick grounding cable in

order to ensure the low impedance under high frequency.

control panel, do not coat the fixing bolt area of the inner plate

and control panel to ensure conductivity in the largest area as

possible.

(d) Ground the control panel using a thick grounding cable in order to

ensure the low impedance under high frequency.

(e) The diameter of cable holes in the control panel must be 10cm

(3.94in.). In order to reduce the chance of radio waves leaking

out, ensure that the space between the control panel and its door

is small as possible.

Paste the EMI gasket directly on the painted surface to seal the

space so that the leak of electric wave can be suppressed.

Our test has been carried out on a panel having the damping

characteristics of 37dB max. and 30dB mean (measured by 3m

method with 30 to 300MHz).

(2) Connection of power and ground wires

Ground and power supply wires for the GOT must be connected as

described below.

(a) Provide a grounding point near the GOT. Short-circuit the LG and

FG terminals of the GOT (LG: line ground, FG: frame ground)

and ground them with the thickest and shortest wire possible

(The wire length must be 30cm (11.81in.) or shorter.)

The LG and FG terminals function is to pass the noise generated

in the PC system to the ground, so an impedance that is as low

as possible must be ensured. As the wires are used to relieve the

noise, the wire itself carries a large noise content and thus short

wiring means that the wire is prevented from acting as an

antenna.

Note) A long conductor will become a more efficient antenna at

high frequency.

(b) The earth wire led from the earthing point must be twisted with

the power supply wires.

By twisting with the earthing wire, noise flowing from the power

supply wires can be relieved to the earthing. However, if a filter is

installed on the power supply wires, the wires and the earthing

wire may not need to be twisted.

4.1.3 Noise filter (power supply line filter)

The noise filter (power supply line filter) is a device effective to reduce

conducted noise. Except some models, installation of a noise filter onto

the power supply lines is not necessary. However conducted noise can

be reduced if it is installed. (The noise filter is generally effective for

reducing conducted noise in the band of 10MHz or less.) Usage of the

following filters is recommended.

The precautions required when installing a noise filter are described

below.

(1) Do not install the input and output cables of the noise filter together

to prevent the output side noise will be inducted into the input side

cable where noise has been eliminated by the noise filer.

(2) Connect the noise filter's ground terminal to the control panel with

the shortest cable as possible (approx. 10cm (3.94 in.) or less).

Model name FN343-3/05 FN660-6/06 RSHN-2003

Manufacturer SCHAFFNER SCHAFFNER TDK

Rated current 3A 6A 3A

Rated voltage 250V

• Installing the input and output cables

together will cause noise induction.

• Separate the input cable from the output

cable.

Filter

Induction

Output side

(device side)

Input side

(power supply side)

Filter

Output side

(device side)

Input side

(power supply side)

4.2 Requirements for Compliance with the Low

Voltage Directive

The Low Voltage Directive requires each device which operates with

power supply ranging from 50VAC to 1000V and 75VDC to 1500V to

satisfy necessary safety items.

In the Sections from

4.2.1 to 4.2.5, cautions on installation and wiring of

the GOT to conform to the Low Voltage Directive requires are described.

We have put the maximum effort to develop this material based on the

requirements and standards of the Directive that we have collected.

However, compatibility of the devices which are fabricated according to

the contents of this manual to the above Directive is not guaranteed.

Each manufacturer who fabricates such device should make the final

judgement about the application method of the Low Voltage Directive

and the product compatibility.

4.2.1 Standard subject to GOT

4.2.2 Power supply

The insulation specification of the GOT was designed assuming

installation category II. Be sure to use the installation category II power

supply to the GOT.

The installation category indicates the durability level against surge

voltage generated by lightning strike.

Category I has the lowest durability; category IV has the highest

durability.

Installation category

Category II indicates a power supply whose voltage has been reduced

by two or more levels of isolating transformers from the public power

distribution.

4.2.3 Control panel

Because the GOT is open type equipment (device designed to be stored

within another device), be sure to use it only when installed in a control

panel.

(1) Shock Protection

In order to prevent those who are unfamiliar with power facility,

e.g., an operator, from getting a shock, make sure to take the

following measures on the control panel.

(a) Store the GOT within the control panel locked, and allow only

those who are familiar with power facility to unlock the panel.

(b)Build the structure in order that the power supply will be shut off

when the control panel is opened.

(2) Dustproof and waterproof features

The control panel also provides protection from dust, water and

other substances. Insufficient ingression protection may lower the

insulation withstand voltage, resulting in insulation destruction.

The insulation in the GOT is designed to cope with the pollution

level 2, so use in an environment with pollustion level 2 or better.

4.2.4 Grounding

The following are applicable ground terminals. Use them in the grounded

state.

Be sure to ground the GOT for ensuring the safety and complying with

the EMC Directive.

Standard applied to GOT : EN61131-2 Programmable controllers - Equipment

requirements and tests

Pollution level 1: An environment where the air is dry and conductive

dust does not exist.

Pollution level 2: An environment where conductive dust does not

usually exist, but occasional temporary conductivity

occurs due to the accumulated dust.

Generally, this is the level for inside the control panel

equivalent a control room or on the floor of a typical

factory.

Pollution level 3: An environment where conductive dust exits and

conductivity may be generated due to the accumulated

dust.

An environment for a typical factory floor.

Pollution level 4: Continuous conductivity may occur due to rain, snow,

etc. An outdoor environment.

Functional grounding : Improves the noise resistance.

Category ICategory IICategory IIICategory IV

4.2.5 External wiring

(1) External devices

When a device with a hazardous voltage circuit is externally

connected to the GOT, select a model which complies with the

Low Voltage Directive's requirements for isolation between the

primary and secondary circuits.(2)Insulation requirements

Dielectric withstand voltages are shown in the following table.

Reinforced Insulation Withstand Voltage

(Installation Category II, source : IEC664)

5. INSTALLATION

5.1 Control Panel Inside Dimensions for

Mounting GOT

Install the GOT on the control panel out of the way for the equipment

inside the control panel. Do not install the GOT and the unit in

prohibited areas for the installation.

5.2 Panel Cutting Dimensions

5.3 Mounting Position

When mounting the GOT, the following clearances must be maintained

from other structures and devices.

Some cables may need to be longer than the specified dimensions when

connecting to the GOT.

Therefore, consider the connector dimensions and bending radius of the

cable as well for installation.

For the lead-in allowance for cables at the bottom of the GOT, refer to

the GOT2000 Series User’s Manual (Hardware).

According to the dimensions in the following table, leave clearances

between the GOT and the other devices. The values enclosed in square

brackets apply to the case where no other equipment generating

radiated noise (such as a contactor) or heat is installed near the GOT.

However, keep the ambient temperature of the GOT to 55°C or lower.

Rated voltage of hazardous

voltage area

Surge withstand voltage (1.2/50 s)

150 VAC or below 2500V

300 VAC or below 4000V

Point

Applicable cable

Some cables may need to be longer than the specified dimensions when connecting to the

GOT. Therefore, consider the connector dimensions and bending radius of the cable as

well for installation.

Unit: mm (inch)

*Panel thickness : 1.6 to 4 mm

(0.06 to 0.16 inch)

GOT A B

GT2310

GT2308

289 (11.38)

227 (8.94)

+2 (0.08)

0 (0)

+2 (0.08)

0 (0)

200 (7.87)

176 (6.93)

+2 (0.08)

0 (0)

+2 (0.08)

0 (0)

Panel thickness: 1.6 to 4mm

(0.06 to 0.16 inch)

Unit : mm(inch)

*1: When opening or closing the battery cover: 72(2.83) or more

5.4 Control Panel Inside Temperature and

Installation Angle

When installing the GOT to a panel, set the display section as shown

below.

Using the GOT with the installation angle other than the following

deteriorates the GOT earlier.

When installing the GOT with the installation angle between 60 to 105 °,

the temperature inside the control panel must be within 55 °C.

When installing the GOT with the installation angle other than between

60 to 105 °, the temperature inside the control panel must be within 40

°C.

Item GT2310 GT2308

48(1.89) or more

[18(0.71) or more]

78(3.07) or more

[18(0.71) or more]

When the SD card is used

50(1.97) or more

[20(0.79) or more]

50(1.97) or more

When the SD card is not

used

50(1.97) or more

[20(0.79) or more]

50(1.97) or more

[20(0.79) or more]

100(3.94) or more

[20(0.79) or more]

GOT

Display section

Panel or others

105°

60°

5. INSTALLATION

5.1 Dimensions intérieures du tableau de

commande pour le montage du GOT

Installez le GOT sur le tableau de commande en laissant de l'espace

pour le dispositif à l'intérieur du tableau de commande. N'installez

pas le GOT et le module dans des zones où l'installation est interdite.

5.2 Cotes de découpe du panneau

5.3 Position de montage

Lors du montage du GOT, laissez les espaces suivants pour les autres

structures et dispositifs.

Certains câbles peuvent être plus longs que les dimensions spécifiées

lors de la connexion au GOT.

Par conséquent, prenez également en compte les dimensions du

connecteur et le rayon de courbure du câble pour l'installation.

Pour connaître l'espace à laisser pour les câbles sous le GOT, référez-

vous au manuel GOT2000 Series User’s Manual (Hardware).

Laissez les espaces entre le GOT et les autres dispositifs en fonction

des dimensions contenues dans le tableau suivant. Les valeurs entre

parenthèses s'appliquent au cas où aucun dispositif générant des

émissions sonores (comme un contacteur) ou de la chaleur n'est installé

près du GOT. Toutefois, maintenez la température ambiante du GOT à

55°C ou moins.

Unité : mm (pouce)

*1: Pour ouvrir ou fermer le couvercle de la batterie : 72 (2,83) ou plus

Point

Câble applicable

Certains câbles peuvent être plus longs que les dimensions spécifiées lors de la

connexion au GOT. Par conséquent, prenez également en compte les dimensions du

connecteur et le rayon de courbure du câble pour l'installation.

Article GT2310 GT2308

48 (1,89) ou plus

[18 (0,71) ou plus]

78 (3,07) ou plus

[18 (0,71) ou plus]

Quand la carte SD est

utilisée

50 (1,97) ou plus

[20 (0,79) ou plus]

50 (1,97) ou plus

Quand la carte SD n'est

pas utilisée

50 (1,97) ou plus

[20 (0,79) ou plus]

50 (1,97) ou plus

[20 (0,79) ou plus]

100 (3,94) ou plus

[20 (0,79) ou plus]

Unité : mm (pouce)

paisseur du panneau : 1,6 à 4mm

(0,06 à 0,16 pouce)

GOT A B

GT2310

GT2308

289 (11,38)

227 (8,94)

+2 (0,08)

0 (0)

+2 (0,08)

0 (0)

200 (7,87)

176 (6,93)

+2 (0,08)

0 (0)

+2 (0,08)

0 (0)

Épaisseur du panneau : 1,6 à 4mm

(0,06 à 0,16 pouce)

5.4 Température intérieure et angle

d'installation du tableau de commande

Lors de l'installation du GOT sur un panneau, réglez la zone d'affichage

comme indiqué ci-dessous.

Si l'angle d'installation est différent de celui indiqué, le GOT se détériore

plus tôt.

Lors de l'installation du GOT avec un angle d'installation compris entre

60 et 105°, la température à l'intérieur du tableau de commande doit être

d'environ 55°C.

Lors de l'installation du GOT avec un angle d'installation non compris

entre 60 et 105°, la température à l'intérieur du tableau de commande

doit être d'environ 40°C.

6. MAINTENANCE AND INSPECTION

Refer to the GOT2000 Series User’s Manual (Hardware) for

maintenance and inspection for the GOT.

GOT

Zone d'affichage

Tableau ou autres

105°

60°

Warranty

Mitsubishi Electric will not be held liable for damage caused by

factors found not to be the cause of Mitsubishi Electric; machine

damage or lost profits caused by faults in the Mitsubishi Electric

products; damage, secondary damage, accident compensation

caused by special factors unpredictable by Mitsubishi Electric;

damages to products other than Mitsubishi Electric products; and to

other duties.

For safe use

• This product has been manufactured as a general-purpose part for

general industries, and has not been designed or manufactured to

be incorporated in a device or system used in purposes related to

human life.

• Before using the product for special purposes such as nuclear

power, electric power, aerospace, medicine or passenger

movement vehicles, consult with Mitsubishi Electric.

• This product has been manufactured under strict quality control.

However, when installing the product where major accidents or

losses could occur if the product fails, install appropriate backup or

failsafe functions in the system.

Country/Region Sales office/Tel

USA Mitsubishi Electric Automation, Inc.

500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A.

Tel: +1-847-478-2100

Brazil Mitsubishi Electric do Brasil Comercio e Servicos Ltda.

Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP, Brazil

Tel: +55-11-4689-3000

Mexico Mitsubishi Electric Automation, Inc. Mexico Branch

Boulevard Miguel de Cervantes Saavedra 301, Torre Norte Piso 5, Ampliacion Granada,

Miguel Hidalgo, Ciudad de Mexico, Mexico, C.P.11520

Tel: +52-55-3067-7512

Germany Mitsubishi Electric Europe B.V. German Branch

Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany

Tel: +49-2102-486-0

UK Mitsubishi Electric Europe B.V. UK Branch

Travellers Lane, UK-Hatfield, Hertfordshire, AL10 8XB, U.K.

Tel: +44-1707-28-8780

Italy Mitsubishi Electric Europe B.V. Italian Branch

Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7,

20864 Agrate Brianza (MB), Italy

Tel: +39-039-60531

Spain Mitsubishi Electric Europe B.V. Spanish Branch

Carretera de Rubi, 76-80-Apdo. 420, E-08190 Sant Cugat del Valles (Barcelona), Spain

Tel: +34-935-65-3131

France Mitsubishi Electric Europe B.V. French Branch

25, Boulevard des Bouvets, 92741 Nanterre Cedex, France

Tel: +33-1-55-68-55-68

Czech Mitsubishi Electric Europe B.V. Czech Branch

Pekarska 621/7, 155 00 Praha 5, Czech Republic

Tel: +420-255 719 200

Turkey Mitsubishi Electric Turkey A.S. Umraniye Branch

Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey

Tel: +90-216-526-3990

Poland Mitsubishi Electric Europe B.V. Polish Branch

ul. Krakowska 48, 32-083 Balice, Poland

Tel: +48-12-347-65-00

Russia Mitsubishi Electric (Russia) LLC St. Petersburg Branch

Piskarevsky pr. 2, bld 2, lit "Sch", BC "Benua", office 720; 195027 St. Petersburg, Russia

Tel: +7-812-633-3497

South Africa Adroit Technologies

20 Waterford Office Park, 189 Witkoppen Road, Fourways, South Africa

Tel: +27-11-658-8100

China Mitsubishi Electric Automation (China) Ltd.

Mitsubishi Electric Automation Center, No.1386 Hongqiao Road, Shanghai, China

Tel: +86-21-2322-3030

Taiwan SETSUYO ENTERPRISE CO., LTD.

6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan

Tel: +886-2-2299-2499

Korea Mitsubishi Electric Automation Korea Co., Ltd.

7F to 9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu,

Seoul 07528, Korea

Tel: +82-2-3660-9569

Singapore Mitsubishi Electric Asia Pte. Ltd.

307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943

Tel: +65-6473-2308

Thailand Mitsubishi Electric Factory Automation (Thailand) Co., Ltd.

12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road,

Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand

Tel: +66-2682-6522 to 31

Indonesia PT. Mitsubishi Electric Indonesia

Gedung Jaya 8th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia

Tel: +62-21 3192-6461

Vietnam Mitsubishi Electric Vietnam Company Limited

11th & 12th Floor, Viettel Tower B, 285 Cach Mang Thang 8 Street, Ward 12,

District 10, Ho Chi Minh City, Vietnam.

Tel: +84-28-3910-5945

India Mitsubishi Electric India Pvt. Ltd. Pune Branch

Emerald House, EL-3, J Block, M.I.D.C., Bhosari, Pune - 411026, Maharashtra, India

Tel: +91-20-2710-2000

Australia MITSUBISHI ELECTRIC AUSTRALIA PTY. LTD.

348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W 2116, Australia

Tel: +61-2-9684-7777

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry

of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice.

Printed in Japan, February 2021.

Mitsubishi Electric GT23 Le manuel du propriétaire

Marque: Mitsubishi Electric

Modèle: GT23

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Mitsubishi Electric GT23 Owner's manual

Mitsubishi Electric GT23 Le manuel du propriétaire

Mitsubishi Electric GT23 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents