EarthQuake 10310 Manuel utilisateur

Marque: EarthQuake

Modèle: 10310

Taper: Manuel utilisateur

Ce manuel convient également à

10310 Dually™ Earth Auger Powerhead

Operator's Manual

Original Operating Instructions

Dually™

Earth Auger

Powerhead

P/N: 13509

ECN: 10002

REV2: 06/19/13

Get parts online at

www.getearthquake.com

GAS/OIL

RATIO

50:1

Product #: 10310

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

INTRODUCTION

Congratulations on your investment in quality. Thank you for purchasing an Earthquake™ Dually™ Powerhead. We have worked to

ensure that your powerhead meets the highest standards for usability and durability. With proper care, your powerhead will provide

many years of service.

Read this entire manual before installation and use. Earthquake reserves the right to change, alter or improve the product

and this document at any time without prior notice.

CONTENTS

Introduction .......................................................................................................................................................................................................................................2

Warnings and Safety Precautions ...........................................................................................................................................................................................3-7

Features ...............................................................................................................................................................................................................................................8

Specications .....................................................................................................................................................................................................................................8

Assembly .............................................................................................................................................................................................................................................9

Operation ................................................................................................................................................................................................................................... 10-11

Maintenance and Storage .................................................................................................................................................................................................... 12-14

Troubleshooting and Repair ................................................................................................................................................................................................14-15

Parts Breakdown ......................................................................................................................................................................................................................16-20

Warranty .....................................................................................................................................................................................................................................21-23

CE Declaration of Conformity ....................................................................................................................................................................................................24

FEDERAL EMISSION INFORMATION

Ardisam warrants to the retail purchaser, that this small, o-road engine was designed, built and equipped to conform at the

time of manufacture to all applicable regulations of the U.S. Environmental Protection Agency (EPA) and those of the State of

California (CARB) when applicable.

REGISTRATION AND SERVICE

This manual may contain information for several models. Read and keep this manual for future reference. This manual contains impor-

tant information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. The owner must be certain that all the product information

is included with the unit. This information includes the MANUAL, the REPLACEMENT PARTS and the WARRANTIES. This information

must be included to make sure state laws and other laws are followed. This manual should remain with the engine even if it is resold.

OWNERSHIP RECORDS

Owner’s Name:

Owner’s Address:

City: State/Province: Zip Code/Postal Code:

Model Number: Serial Number:

Date of Purchase:

Notes:

Record the model number and serial number in the space provided for easy reference when

ordering parts or requesting technical support. Excluding emissions-related warranty items,

the warranty is valid only if the completed registration is received by Earthquake within 30

days of purchase. (SEE WARRANTY SECTION FOR MORE INFORMATION.) You can register

your warranty online by visiting www.getearthquake.com, or by mailing it to: Earthquake,

1160 Eighth Avenue, Cumberland, WI 54829. If you do not have a computer, call our customer

service department to register your product.

Serial

Number

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 3

Operator's Manual

Dually™ Earth Auger Powerhead

WARNINGS AND SAFETY PRECAUTIONS

OPERATOR’S RESPONSIBILITY

Accurate, safe and eective use of this product is the operator’s

responsibility.

• Readandfollowallsafetyinstructions.

• Maintainthismachineaccordingtodirectionsandschedule

included in this operator’s manual.

• Ensurethatanyonewhousesthemachineis familiarwith

and understands all controls and safety precautions.

SAFETY MESSAGES

Your manual contains special messages to bring attention to

potential safety concerns, machine damage as well as helpful

operating and servicing information. Read all the information

carefully to avoid injury and machine damage.

NOTE: General information is given throughout the manual

that may help the operator in the operation or service of the

product.

This symbol points out important safety instruc-

tions which if not followed could endanger your

personal safety.

BEFORE OPERATING ENGINE:

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT

AVOIDED, COULD RESULT IN DEATH OR SERIOUS IN

JURY AND/OR PROPERTY DAMAGE.

CAUTION

CAUTION INDICATES YOU CAN BE HURT OR YOUR

EQUIPMENT DAMAGED IF THE SAFETY INSTRUC

TIONS THAT FOLLOW THIS SIGNAL WORD ARE NOT

OBEYED.

WARNING

CALIFORNIA PROPOSITION 65 WARNING

ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER RE

PRODUCTIVE HARM.

IMPORTANT

INDICATES HELPFUL INFORMATION FOR PROPER AS

SEMBLY, OPERATION, OR MAINTENANCE OF YOUR

EQUIPMENT.

WARNING

READ AND COMPLY WITH ENTIRE OPERATING AND

MAINTENANCE INSTRUCTIONS FOR THIS MACHINE,

IN ADDITIONAL TO ALL SAFETY INSTRUCTIONS. FAIL

URE TO FOLLOW AND/OR COMPLY WITH THESE IN

STRUCTIONS COULD RESULT IN LOSS OF MACHINE

CONTROL, SERIOUS PERSONAL INJURY OR DEATH TO

YOU AND/OR BYSTANDERS, AND EQUIPMENT AND

PROPERTY DAMAGE. OPERATE THE ENGINE ACCORD

ING TO THE SAFETY INSTRUCTIONS OUTLINED HERE

AND INSERTED THROUGHOUT THE TEXT. ANYONE

WHO USES THIS MACHINE MUST READ THE INSTRUC

TIONS AND BE FAMILIAR WITH THE CONTROLS.

WARNING

CERTAIN COMPONENTS IN THIS MACHINE AND ITS RE

LATED ACCESSORIES CONTAIN CHEMICALS KNOWN

TO THE STATE OF CALIFORNIA TO CAUSE CANCER,

BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM.

WASH HANDS AFTER HANDLING.

Intended Use /

Foreseeable Misuse

This is a motorized earth auger powerhead that drills into soil. It

is pedestrian controlled. It has a petrol-fueled internal combus-

tion engine that powers the auger blades. It shall not be used

for any other purpose.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

GENERAL SAFETY RULES

• Read, understand, and follow all instructions on the ma-

chine and in the manual(s). Be thoroughly familiar with the

controls and the proper use of the machine before starting.

• Use this equipment for its intended purpose only.

• Familiarize yourself with all of the safety and operating

decals on this equipment and on any of its attachments or

accessories.

• Do not put hands or feet near or under rotating parts.

• Only allow responsible individuals who are familiar with the

instructions to operate the machine. Do not allow children

to operate this machine. Do not allow adults to operate the

machine without proper instruction.

• Thoroughly inspect the area where the machine is to be

used and remove all foreign objects. Your equipment can

propel small objects at high speed causing personal injury

or property damage. Stay away from breakable objects such

as house windows.

• Wear appropriate clothing such as a long-sleeved shirt or

jacket. Also wear long trousers or slacks. Do not wear shorts.

Never wear sandals, sneakers, or open shoes, and never

operate the machine with bare feet.

• Do not wear loose clothing or jewelry. They can get caught in

moving parts. Always keep hands, feet, hair and loose clothing

away from any moving parts on engine and machine.

• Always wear safety goggles or safety glasses with side shields

when operating the machine to protect your eyes from

foreign objects which can be thrown from the unit. Always

wear a protective hearing device.

• Always wear work gloves and sturdy footwear. Wear

footwear that will improve footing on slippery surfaces.

Leather work shoes or short boots work well for most people.

These will protect the operator’s ankles and shins from small

sticks, splinters, and other debris.

• It is advisable to wear protective headgear to prevent the

possibility of being struck by small ying particles, or being

struck by low hanging branches, twigs, or other objects

which may be unnoticed by the operator.

• Do not operate the machine without proper guards or other

safety devices in place.

• See Earthquake instructions for proper operation and

installation of accessories. Only use accessories approved

by Earthquake.

• Operate only in daylight or good articial light.

• Do not operate machine when fatigued or under the

influence of alcohol, drugs or other medication which

can cause drowsiness or aect your ability to operate this

machine safely.

• Never operate machine in wet grass. Always be sure of your

footing; keep a rm hold on the handle and walk; never run.

• Watch for traffic when operating near, or when

crossing roads.

• If the equipment should start to vibrate abnormally, stop the

engine (motor), disconnect the spark plug wire and prevent

it from touching the spark plug. Check immediately for cause.

Vibration is generally a warning of trouble. If the noise or

vibrations of the machine increase, stop immediately and

perform an inspection.

• Never leave the machine unattended when the engine is

running.

• Regularly inspect the machine. Make sure parts are not bent,

damaged or loose.

• Temperature of muer and nearby areas may exceed 150° F

(65° C). Allow muer and engine areas to cool before touching.

Never pick up or carry the machine while the engine is running.

• Prolonged exposure to noise and vibration from gasoline engine-

powered equipment should be avoided. Take intermittent

breaks and/or wear ear protection from engine noise as well as

heavy work gloves to reduce vibration in the hands.

• Keep all screws, nuts and bolts tight.

• Do not transport the machine from one place to another

with the engine running.

• Check local regulations for age restrictions on use of this

machine.

PRODUCTSPECIFIC SAFETY RULES

• Do not drill above underground utilities, including water

lines, gas lines, electric cables, or pipes. Do not operate the

powerhead and earth auger in soil with large rocks and

foreign objects which can damage the equipment.

• After striking a foreign object, stop the engine. Remove the

wire from the spark plug. Inspect the powerhead and auger

for damage. If damaged, repair before starting and operating

the powerhead and auger.

• The auger should not rotate when the engine is idling. If it

does rotate when engine is idling, contact Earthquake for

instructions.

• If an object becomes lodged in the auger, turn the engine o,

remove the wire from the spark plug and secure away from

the spark plug; allow to cool before attempting to remove

the foreign object.

• The earth blade is very sharp. Use extreme caution when

drilling a hole or replacing the blade.

• Do not carry the earth auger unit between holes with the

engine running.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 5

Operator's Manual

Dually™ Earth Auger Powerhead

CAUTION

HOT GASES ARE A NORMAL BYPRODUCT OF A FUNC

TIONING CATALYTIC CONVERTER. FOLLOW ALL SAFE

TY INSTRUCTIONS TO PREVENT BURNS AND FIRES.

DO NOT ALTER/MODIFY ENGINE:

NEVER ALTER OR MODIFY THE ENGINE FROM THE

FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF

ENGINE IS MODIFIED OR ALTERED.

WHEN WORKING ON OR REPLACING PARTS FOR THE

ENGINE OR MACHINE, YOU MUST ALWAYS DISCON

NECT THE SPARK PLUG WIRE FROM THE SPARK PLUG

AND KEEP IT AWAY FROM THE SPARK PLUG.

ENGINE SAFETY PRECAUTIONS

Warning Carbon Monoxide Poisoning

Engines give off carbon monoxide, an odorless, colorless,

poison gas. Carbon monoxide may be present even if you do not

smell or see any engine exhaust. Breathing carbon monoxide

can cause nausea, fainting or death, in addition to drowsiness,

dizziness and confusion. If you experience any of these

symptoms, seek fresh air and medical attention immediately.

If your machine comes with a separate engine manual, be

sure to read and follow all safety and warning precautions

outlined there, in addition to any in this manual.

Preventing Carbon Monoxide Poisoning

• Always start and run engine outdoors. Do not start or run

engine in an enclosed area, even if doors or windows are open.

• Never try to ventilate engine exhaust indoors. Carbon

monoxide can reach dangerous levels very quickly.

• Never run engine outdoors where exhaust fumes may be

pulled into a building.

• Never run engine outdoors in a poorly ventilated area where

the exhaust fumes may be trapped and not easily taken

away. (Examples include: in a large hole or areas where hills

surround your working area.)

• Never run engine in an enclosed or partially enclosed area.

(Examples include: buildings that are enclosed on one or

more sides, under tents, car ports or basements.)

• Always run the engine with the exhaust and muer pointed

in the direction away from the operator.

• Never point the exhaust muer towards anyone. People

should always be many feet away from the operation of the

engine and its attachments.

• Do not change the engine governor settings or over-speed

the engine.

WARNING

ENGINES GIVE OFF CARBON MONOXIDE, AN ODOR

LESS, COLORLESS, POISON GAS. CARBON MONOXIDE

MAY BE PRESENT EVEN IF YOU DO NOT SMELL OR SEE

ANY ENGINE EXHAUST. BREATHING CARBON MON

OXIDE CAN CAUSE NAUSEA, FAINTING OR DEATH, IN

ADDITION TO DROWSINESS, DIZZINESS AND CONFU

SION.

IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK

FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.

Gasoline Fires and Handling Fuel Safely

Use extra care in handling gasoline and other fuels. They are

ammable and vapors are explosive.

• When storing extra fuel be sure that it is in an appropriate

container and away from any re hazards.

• Prevent re and explosion caused by static electric discharge.

Use only nonmetal, portable fuel containers approved by the

Underwriter’s Laboratory (U.L.) or the American Society for

Testing & Materials (ASTM).

• Always ll fuel tank outside in a well ventilated area. Never

fill your fuel tank with fuel indoors. (Examples include:

basement, garage, barn, shed, house, porch, etc.) Never

ll tank near appliances with pilot lights, heaters, or other

ignition sources. If the fuel has to be drained, this should

be done outdoors. The drained fuel should be stored in a

container specically designed for fuel storage or it should

be disposed of carefully.

• Never remove the fuel cap or add fuel with the engine

running. Stop engine and allow to cool before lling.

• Do not smoke while refueling or operating engine.

• Never drain fuel from the engine in an enclosed area.

• Always wipe up excess (spilled) fuel from engine before

starting. Clean up spilled fuel immediately. If fuel is spilled,

do not start the engine but move machine and fuel container

from area. Clean up spilled fuel and allow to evaporate and

dry after wiping and before starting.

• Allow fuel fumes/vapors to escape from the area before

starting engine.

• Test the fuel cap for proper installation before starting and

using engine.

• Always run the engine with fuel cap properly installed on

the engine.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

• Do not store engine with fuel in the fuel tank indoors. Fuel

and fuel vapors are highly explosive.

• During storage, keep machine so gas cap is up.

• Never siphon fuel by mouth to drain fuel tank.

• Always have an adult fill the fuel tank and never allow

children to ll the engine.

• Never allow an adult or anyone under the inuence of drugs

or alcohol to ll engine.

• When storing gasoline or equipment with fuel in the tank,

store away from furnaces, stoves, water heaters or other

appliances that have a pilot light or other ignition source

because they can ignite gasoline vapors.

BURNS AND FIRES

The muer, muer guard and other parts of the engine be-

come extremely hot during the operation of the engine. These

parts remain extremely hot after the engine has stopped.

Prevention of Burns and Fires

• Neverremovethemuerguardfromtheengine.

• Nevertouchthemuerguardbecauseitisextremelyhot

and will cause severe burns.

• Nevertouch partsof theenginethatbecomehot after

operation.

• Alwayskeepmaterialsanddebrisawayfrommuerguard

and other hot parts of the engine to avoid res.

CHILDREN AND BYSTANDERS

Tragic accidents can occur if the operator is not alert to the

presence of children and/or bystanders. Never assume that

others will remain where you last saw them.

• Keep the area of operation clear of all persons, especially

small children and pets. Keep children under the watchful

care of a responsible adult.

• Be alert and turn the machine o if children enter the area.

• Before and while moving backwards, look behind and down

for small children.

• Never allow children to operate the machine

AUGER SAFETY RULES

• Carry powerhead and auger by handle bars only, NOT by

auger.

• Keep all body extremities, loose clothing and foreign objects

clear of rotating auger.

• Be sure auger is securely attached to powerhead during use.

• Never carry auger between holes with the engine running.

• This auger is not designed to be utilized as an anchoring

device.

SERVICE

• Always stop the engine whenever you leave the machine,

before cleaning, repairing or inspecting the unit. The

engine should be turned o and cool, the spark plug wire

must be removed from the spark plug before any repairs

or adjustments are attempted. Never make adjustments

or repairs with the engine (motor) running. Disconnect

the spark plug wire, and keep the wire away from the plug

to prevent accidental starting. Remove the ignition key if

equipped with an electric start.

• Always wear eye protection when you make adjustments or

repairs.

• Keep all nuts and bolts tight and keep equipment in good

condition.

• Never tamper with safety devices. Check their proper

operation regularly.

• When servicing or repairing the machine, do not tip the

machine over or up unless specically instructed to do so in

this manual. Service and repair procedures can be done with

the machine in an upright position. Some procedures will be

easier if the machine is lifted on a raised platform or working

surface.

• To reduce re hazard, keep machine free of grass, leaves,

or other debris build-up. Clean up oil or fuel spillage. Allow

machine to cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Clean and replace safety and instruction decals as necessary.

• To guard against engine over-heating, always have engine

debris lter mounted and clean.

• Inspect the machine before storage. When not in use,

disconnect the spark plug lead and store indoors in a dry

place locked or otherwise inaccessible to children.

• Use only original equipment parts from Earthquake,

including all nuts and bolts.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 7

Operator's Manual

Dually™ Earth Auger Powerhead

GAS/OIL

RATIO

50:1

Fire hazards

Wear hearing and

eye protection

Shock hazard

Hot surfaces

Toxic fumes

Moving parts

Read manual before operation

Slow

Fast

Fuel

Oil

Choke

On/O

Fuel Shuto

SAFETY SYMBOLS AND DECALS

GAS/OIL

RATIO

50:1

Operational Control Symbols

This powerhead has been designed and manufactured to provide you with the safety and reliability you would expect from an

industry leader in outdoor power equipment manufacturing.

Reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this

equipment safely and eectively. We have placed a safety decal on the powerhead to remind you of some of this important information

while you are operating the unit. These important safety decals are illustrated below, and are shown here to help familiarize you

with the location and content of the safety messages you will see as you perform normal drilling operations. Review these decals

now, and if you have any questions regarding their meaning or how to comply with these instructions, reread the complete safety

instruction text in this manual. For additional questions European customers may contact their local dealer and US customers must

call Earthquake customer service.

Should a decal become unreadable because of being worn, faded, or otherwise damaged during the use of your powerhead, use the

part number information provided to order a replacement label. European customers can order from their local authorized dealer

and US customers can order by calling Earthquake customer service. These decals are easily applied, and will act as a constant visual

reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, eective operation of

your powerhead.

The following symbols and decals may be used on your engine to alert you to potential hazards or to give you guidance in operating

your powerhead. Look over them and understand their meanings before operating your powerhead.

Safety or Hazard Symbols

Hot! Do not touch!

Part No. 16869

SERIAL NUMBER

DECAL

Part No. 16868

DUALLY SHROUD

DECAL

ARDISAM, INC.

1160 8th Avenue | Cumberland, WI 54829 | USA

Serial No.

Model: Dually

Type: Earth Auger Mass: 9.53 kg

Max. Operating Speed: 285 rpm

(dBA): 104 L

(dBA): 109

16869

Ne pas porter la tarière entre deux forages avec le moteur en marche.

Porter le bloc moteur et la tarière par les poignées seulement, PAS

par l’outil. L’actionnement de la commande des gaz lorsqu’on porte la

tarière peut provoquer des blessures corporelles si les mains ou les

vêtements sont au contact ou à proximité de l’outil en rotation.

WARNING/AVERTISSEMENT

16868

GAS/OIL

ESSENCE/HUILE

50:1

Do not carry auger between holes with engine running. Carry

powerhead and auger by handle bars only, NOT by auger. Activating

throttle control when carrying auger may cause personal injury if

hands or clothing are on or near rotating auger.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

FEATURES

SPECIFICATIONS

Model Operator Ear

(dBA)

Sound Power Level

(dBA)

Dually 104 109

SOUND AND VIBRATION LEVELS

Model Hand/Arm Vibration

Max m/s

Dually 11.9

Sound levels tested in accordance with ISO3744 & ISO 11201 - Grade 2

(Engineering ) Method. Readings taken with engine at full throttle.

EAV = Exposure Action Value, ELV = Exposure Limit Value

fuel tank

fuel cap

throttle control

muer

spark plug

output shaft

starter handle

air lter

choke lever

ON/OFF switch

spark plug

primer bulb

throttle control

Displacement/Cycle 52 cc; 2-cycle

Ignition Type Electronic ignition

Cooling System Forced air cooling

Output Shaft Torque 62 ft. lbs.

Spark Plug Type SEE PARTS BREAKDOWN

Recommended Fuel Type Minimum 87 octane gasoline with

NO ethanol content

NOTE: If using an ethanol blended

fuel, a fuel stabilizer, mixed to

manufacturer specications, is

recommended

Fuel Tank Capacity 0.3 gallon (1.14 liters)

Start Type Recoil

Max Output Shaft Speed 285 RPM

Net Weight 24 lb (9.53 kg)

Overall Dimensions 20.20” x 16.20” x 14.21” (513mm x

411mm x 361mm)

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 9

Operator's Manual

Dually™ Earth Auger Powerhead

UNPACKING

Carefully lift the powerhead out of the box, remove any packing

material and cut any ties.

TOOLS REQUIRED

Two (2) 9/16” Wrenches

ASSEMBLY INSTRUCTIONS

1. Insert the output shaft of the transmission (A) in the open

end of the Flex Coil ShockTop (B).

2. Line up the bolt holes through the Flex Coil ShockTop and

the output shaft of the transmission.

3. Place the included 3/8-16 x 1.5 inch bolt (C) through the bolt

hole.

4. Hand-thread the 3/8-16 “Bi-way” lock nut (D) on the bolt.

5. Using two 9/16 inch wrenches, securely tighten the nut and bolt.

ASSEMBLY

Figure 1

WARNING

DO NOT REFUEL WHILE SMOKING, NEAR OPEN FLAME,

OR OTHER POTENTIAL HAZARDS.

FUEL IS HIGHLY FLAMMABLE AND MUST BE HANDLED

WITH CARE. NEVER FILL THE TANK WHEN THE ENGINE

IS HOT OR RUNNING. ALWAYS MOVE OUTDOORS TO

FILL THE TANK.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

OPERATION

GAS AND OIL QUALITY

To operate the engine, we recommend using Viper® brand 2-cycle

oil (P/N 16890) to ensure that the engine operates correctly

throughout the life of the engine. Viper® brand two-cycle oil

has fuel stabilizer additive which helps to prevent gasoline from

oxidizing and gumming up the carburetor when the unit is not

in use for long periods of time. Use unleaded regular gas only.

It is best to use premium gasoline that has no ethanol content.

NOTE: Viper® oil can be purchased from our web site at www.

getearthquake.com.

MIXTURE

Run earth auger with a 50:1 ratio.

MIXING FUEL AND FILLING GAS TANK

MIXING FUEL

1. Fuel must be mixed in a container outside in a well ventilated

area.

2. Fill certied fuel container 1/4 full of recommended fuel.

3. Add recommended amount of 2 cycle oil.

4. Screw container cap on straight and tight.

5. Shake the container to mix fuel and oil.

6. Unscrew gas cap slowly to vent, add the remainder of fuel

requirements.

7. Wipe away any spilled fuel or oil and allow to evaporate before

moving or transporting.

FILLING FUEL TANK

1. Shut-o engine and allow engine to completely cool before

relling the fuel tank.

2. Move to a well-ventilated area, outdoors, away from ames

and sparks.

3. Clean debris from area around the fuel cap.

4. Loosen fuel cap slowly. Place the cap on a clean, dry surface.

5. Carefully add fuel without spilling.

6. Do not ll fuel tank completely full; allow space for fuel to expand.

7. Immediately replace fuel cap and tighten. Wipe o spilled

fuel and allow to dry before starting engine.

GAS OIL RATIO

1 gallon 2.5 ounces 50:1

2 gallons 5 ounces 50:1

5 gallons 13 ounces 50:1

CAUTION

DO NOT ALTER/MODIFY ENGINE OR AUGER:

NEVER ALTER OR MODIFY THE ENGINE FROM THE

FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF

ENGINE IS MODIFIED OR ALTERED.

WHEN WORKING ON OR REPLACING PARTS FOR THE

ENGINE OR AUGER YOU MUST ALWAYS DISCONNECT

THE SPARK PLUG WIRE FROM THE SPARK PLUG AND

KEEP IT AWAY FROM THE SPARK PLUG.

ALWAYS WEAR HEARING PROTECTION WHILE OPER

ATING ENGINE.

DO NOT START YOUR EARTH AUGER UNTIL YOU HAVE

READ THE PREVIOUS SECTION OF THIS MANUAL. IF

YOU HAVE READ THESE, FOLLOW THE STEPS BELOW

TO START YOUR EARTH AUGER.

NEVER STORE ENGINE WITH GAS IN THE TANK INDOORS.

FUEL AND FUEL VAPORS ARE HIGHLY FLAMMABLE.

NEVER MIX FUEL AND OIL DIRECTLY IN ENGINE GAS

TANK. USE ONLY NONMETAL, PORTABLE FUEL CON

TAINERS APPROVED BY THE UNDERWRITER’S LABO

RATORY U.L. OR THE AMERICAN SOCIETY FOR TEST

ING & MATERIALS ASTM.

HANDLING AND FILLING THE ENGINE WITH FUEL

MUST ALWAYS BE DONE BY AN ADULT.

ALWAYS HANDLE FUEL IN A WELL VENTILATED AREA,

OUTDOORS, AWAY FROM FLAMES OR SPARKS.

IMPORTANT

THIS ENGINE USES A GAS/OIL MIXTURE. DO NOT RUN ON

STRAIGHT GAS ONLY. THIS WILL VOID THE WARRANTY

AND ENGINE DAMAGE WILL RESULT.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 11

Operator's Manual

Dually™ Earth Auger Powerhead

STARTING AND STOPPING ENGINE

• Moveenginetoawellventilatedarea,outdoors,toprevent

carbon monoxide poisoning.

• Movetoanareaawayfromamesorsparks,toavoidignition

of vapors if present.

• Removealldebrisfromaircleanerholesandgascaptoensure

proper air ow.

COLD ENGINE START

Starting engine for rst time or after engine has cooled o or

after running out of fuel.

1. Move choke lever to CHOKE position.

NOTE: CHOKE position is dened by moving the choke lever

as far to the CHOKE position as possible.

2. Prime unit until primer hose is lled with gas.

NOTE: When using the primer bulb, allow the bulb to return

completely to its original position between pushes.

4. Push ON/OFF switch to the ON position.

5. Hold handle bar rmly. Grasp starter handle and pull out slowly,

until it pulls slightly harder. Without letting starter handle retract,

pull rope with a rapid full arm stroke. Let it return to its original

position very slowly until unit res or runs. Repeat this step every

time the starter rope is pulled.

NOTE: If engine fails to start after 5-6 pulls, push primer 1

time and pull starter rope again.

6. Once running, move choke lever to HALF CHOKE position

until unit runs smoothly.

NOTE: HALF CHOKE is dened when the choke lever is be-

tween CHOKE and RUN.

7. Move choke lever to RUN position and move throttle to de-

sired speed.

NOTE: Run at full throttle when possible. Do not let unit idle

for extended periods of time.

8. To stop engine, push ON/OFF switch to OFF position.

WARM ENGINE START

1. Move choke lever to CHOKE position.

NOTE: CHOKE position is dened by moving the choke lever

as far to the CHOKE position as possible.

2. Continue with Step 4 of Cold Engine Starting.

CAUTION

MAKE SURE THE UNIT IS IN A STABLE POSITION BE

FORE PULLING THE STARTER HANDLE.

ALWAYS HANDLE FUEL IN A WELL VENTILATED AREA,

OUTDOORS, AWAY FROM FLAMES OR SPARKS.

ALWAYS WEAR A PROTECTIVE HEARING DEVICE.

DO NOT START ENGINE IF FUEL IS SPILLED. WIPE OFF

EXCESS FUEL AND ALLOW TO DRY. REMOVE ENGINE

FROM AREA TO AVOID SPARKS.

IF AUGER IS MOUNTED TO ENGINE, ALL SAFETY

GUARDS MUST BE SECURELY ON TO AVOID SERIOUS

INJURY.

STARTER ROPE CAN CAUSE AN UNANTICIPATED

JERK TOWARDS ENGINE. FOLLOW INSTRUCTIONS TO

AVOID INJURY.

IF ENGINE FAILS TO START AFTER TRYING STARTING

PROCEDURES, CONTACT OUR CUSTOMER SERVICE

DEPARTMENT AT 8003456007.

NEVER LEAVE ENGINE RUNNING WHILE UNATTEND

ED. TURN OFF AFTER EVERY USE.

NEVER CARRY POWERHEAD AND AUGER BETWEEN

HOLES WHILE ENGINE IS RUNNING.

HOT ENGINE START:

1. Begin with Step 4 of Cold Engine Starting.

2. If engine does not re, refer to Step 1 of Warm Engine Starting.

DO NOT attempt to start engine in the following ways:

• Byusingstartinguid.

• Spraying ammableliquidsorvaporsintoaircleaner,

carburetor or spark plug chamber.

• Removingsparkplugandpullonstarterrope.Flammable

fuel can spray out and ignite from a spark from spark plug.

TO STOP ENGINE:

Push the ON/OFF switch to the OFF position.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

MAINTENANCE AND STORAGE

STEPS FOR WORKING ON EQUIPMENT

1. Turn o engine switch.

2. Disconnect the spark plug wire from the spark plug.

3. Securely place the disconnected spark plug wire away from

the spark plug and any metal parts. This must always be done

or arcing may occur between spark plug wire and metal parts.

4. Replace or repair the part on the powerhead.

5. Check all parts that were repaired, or removed during repair,

that they are secure and t correctly.

NOTE: All repair parts must come from the factory. Never

replace parts that are not specifically designed for the

powerhead.

6. Reconnect the spark plug wire.

POWER AUGER MAINTENANCE

1. The gear case has 4 oz. of grease installed at the factory. It

is recommended that once a year the gear case be split and

the grease level checked. Add grease only if level of grease

is below top of the gears. DO NOT OVERFILL. Replacement

grease is available online per parts breakdown.

2. Keep all screws, nuts, and bolts tight.

3. For cold weather operation, store the unit in a cool environ-

ment. Transferring the unit from a warm to a cold place can

cause the build up of harmful condensation.

4. If auger performance decreases, carefully inspect cutting edge

of blade for any signs of wear. If blades show any of these signs,

they need to be replaced.

ENGINE MAINTENANCE

Read the maintenance schedule and observe these recommen-

dations to extend the life of your engine.

Good maintenance is essential for safe, economical, and trou-

ble-free operation. It will also help reduce air pollution. To help

you properly care for your engine, the following pages include

a maintenance schedule, routine inspection procedures, and

simple maintenance procedures using basic hand tools. Other

service tasks that are more difficult, or require special tools, are

best handled by professionals and are normally performed by a

technician or other qualified mechanic.

Maintenance, replacement or repair of the emissions con-

trol devices and systems may be performed by any non-

road engine repair establishment or individuals. However,

items must be serviced by an authorized dealer to obtain

"no charge" emissions control service.

CAUTION

TO PREVENT ACCIDENTAL STARTING:

ENGINE MUST BE TURNED OFF AND COOL, AND

SPARK PLUG WIRE MUST BE REMOVED FROM SPARK

PLUG BEFORE CHECKING AND ADJUSTING ENGINE

OR EQUIPMENT.

TEMPERATURE OF MUFFLER AND NEARBY AREAS

MAY EXCEED 150º F. 65º C. AVOID THESE AREAS.

CHECK AUGER OFTEN FOR LOOSE NUTS AND BOLTS.

KEEP THESE ITEMS TIGHTENED.

NEVER STORE ENGINE WITH FUEL IN THE TANK IN

SIDE A BUILDING. POTENTIAL SPARKS MAY BE PRES

ENT FOR IGNITION OF FUEL AND FUEL VAPORS.

ANY MAINTENANCE AND REPAIR ON THE ENGINE

AND AUGER MUST ALWAYS BE DONE BY AN ADULT.

ENGINE MUST BE SHUTOFF, COOL, AND SPARK PLUG

WIRE REMOVED BEFORE ANY REPAIR OR MAINTE

NANCE CAN BE DONE.

MAINTENANCE ITEM

Every 8

hours

(daily)

Every 20

hours or

seasonally Yearly

Clean Engine and Check Bolts & Nut X

Air Filter Check X

(See Air Filter section) Clean * X

Replace X

Spark Plug (Gap .028”) Check/

Adjust

(See Spark Plug

section)

Replace X

* Service more frequently under dusty conditions

MAINTENANCE SCHEDULE

IMPORTANT

NEVER TWIST AIR FILTERS WHEN CLEANING. ALWAYS

PRESS.

The maintenance schedule applies to normal operating condi-

tions. If you operate your engine under unusual conditions, such

as sustained high-load or high-temperature operation, or use in

unusually wet or dusty conditions, consult your servicing dealer

for recommendations applicable to your individual needs and use.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 13

Operator's Manual

Dually™ Earth Auger Powerhead

COOLING FINS

Cooling ns, air inlets and linkages must be free from any debris

before each use.

AIR FILTER

Never run engine without air cleaner properly installed. Added

wear and engine failure may occur if air cleaner is not installed

on engine.

Service air cleaner every 3 months or after 20 hours of operation.

Clean lter daily in extremely dusty conditions.

STEPS FOR CLEANING BLOCK STYLE FOAM AIR FILTER

1. Before removing the air lter cover, move the choke lever to

the choke position. SEE FIGURE 2.

2. To remove air lter cover, squeeze the latch tabs on both sides

of the cover. SEE FIGURE 3.

3. Once the latch tabs are released, remove the air lter cover

by rotating the cover away from the engine. SEE FIGURE 4.

4. Remove the foam lter element (SEE FIGURE 5) and replace

with a new oiled lter, or clean the original foam lter with

warm water and mild soap by following the previous steps for

Cleaning Air Filter. Remember to thoroughly oil the foam lter

with 30 or 40 weight motor oil and squeeze out any excess

oil.

5. Reinstall the foam lter, pressing it in place to ensure that the

foam is fully seated into its sealed position. SEE FIGURE 6.

6. Replace the air lter cover so that it fully snaps into place and

is secured by the latch tabs. Check that the cover is securely

attached by pulling slightly on the cover. If the cover doesn’t

move when pulled, it is secure.

Figure 2

Figure 3

Figure 4 Figure 5

Figure 6

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

SPARK PLUG

See parts breakdown for recommended spark plug.

1. Check spark plug at the beginning of each season.

2. Disconnect the spark plug cap, and clean any debris from

around the spark plug area.

3. Remove spark plug and replace if any of the following occur;

pitted electrodes, burned electrodes, cracked porcelain, or

deposits around electrodes.

4. After analysis, seat spark plug and tighten with spark plug

wrench.

• Reinstalloriginalsparkplug,tightenadditional1/2turn.

• Installingnewsparkplug,adjustsparkpluggapto.028”and

tighten additional 1/8 – 1/4 turn .

NOTE: Loose spark plug may overheat and damage engine.

Over tightened spark plug may damage threads in the

cylinder head.

CARBURETOR

Never tamper with factory setting of the carburetor.

TRANSPORTING YOUR EARTH AUGER

1. Never transport engine inside an enclosed space or vehicle.

Fuel or fuel vapors may ignite causing serious injury or death.

2. If fuel is present in the fuel tank, transport in an open vehicle

in an upright position.

3. If an enclosed vehicle must be used, remove gas into an ap-

proved red fuel container. DO NOT siphon by mouth.

4. Run engine to use up the fuel in the carburetor and fuel tank.

Always run engine in a well ventilated area.

5. Wipe away any spilled fuel from engine and earth auger. Allow

to dry.

LONGTERM STORAGE

30 DAYS OR MORE WITHOUT USE

If your earth auger will not be used for more than one month,

prepare it for long term storage.

STEPS FOR LONGTERM STORAGE

1. Add fuel stabilizer according to manufacturer’s instructions.

2. Run engine for 10-15 minutes to ensure that the stabilizer

reaches the carburetor.

3. Remove the remainder of the fuel from the gas tank into an

approved fuel container.

4. Remove auger from powerhead and apply a thin layer of

grease to the output shaft of the transmission.

5. Store auger and powerhead (engine) in a vertical position.

6. Remove all debris from auger and powerhead (engine).

CAUTION

TO AVOID INJURY OR DEATH, NEVER SIPHON FUEL BY

MOUTH.

NEVER STORE EARTH AUGER WITH FUEL IN THE GAS

TANK INSIDE AN ENCLOSED AREA OR BUILDING.

TO PREVENT ACCIDENTAL STARTING:

ENGINE MUST BE TURNED OFF AND COOL, AND

SPARK PLUG WIRE MUST BE REMOVED FROM SPARK

PLUG BEFORE CHECKING AND ADJUSTING ENGINE

OR EQUIPMENT.

MAINTENANCE AND REPAIR ON THE ENGINE AND AU

GER MUST ALWAYS BE DONE BY AN ADULT.

ENGINE MUST BE SHUTOFF, COOL, AND SPARK PLUG

WIRE REMOVED BEFORE ANY REPAIR OR MAINTE

NANCE CAN BE DONE.

TROUBLESHOOTING AND REPAIR

At Earthquake, we build quality and durability into the design of

our products; but no amount of careful design by us, and careful

maintenance by you, can guarantee a repair-free life for your

Earthquake powerhead. Most repairs will be minor, and easily

xed by following the suggestions in the troubleshooting guide

in this manual.

The troubleshooting guide will help you pinpoint the causes of

common problems and identify remedies.

For more complicated repairs, you may want to rely on an

authorized service center or Earthquake. A parts breakdown is

located toward the end of this manual.

We will always be glad to answer any questions you have, or

help you nd suitable assistance. To order parts or inquire about

warranty, call or e-mail us using the contact information found

under "Ordering Replacement Parts".

ORDERING REPLACEMENT PARTS

Parts can be obtained directly from the factory. To order parts

visit www.getearthquake.com or call 1-800-345-6007.

For other general questions, you can e-mail us at [email protected]om.

IN CASE OF A SERVICE PROBLEM, DO NOT SEND PRODUCT

BACK TO RETAILER. CONTACT EARTHQUAKE AT 800345

6007.

Include the following information with your order:

1) Part numbers

2) Part description

3) Quantity

4) Model number and serial number

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 15

Operator's Manual

Dually™ Earth Auger Powerhead

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE REMEDY/ACTION

Engine will not start 1. Power switch o 1. Flip switch to ON position

2. Spark plug wire disconnected 2. Connect spark plug wire to spark plug

3. Out of fuel 3. Refuel

4. Spark plug wet, faulty or improperly

gapped

4. Clean, replace or gap spark plug

5. Fuel line hose not positioned in bottom of

gas tank

5. Push fuel line down into fuel in gas tank

6. Stale fuel 6. Drain old fuel and replace with fresh. Use fuel stabi-

lizer for future preventative measures.

Engine runs rough, oods during

operation

1. Dirty air lter 1. Clean or replace air lter

2. Choke partially engaged 2. Turn o choke

3. Carburetor out of adjustment 3. Call factory or take to authorized repair center

Engine is hard to start 1. Stale fuel 1. Drain old fuel and replace with fresh. Use gas stabi-

lizer for future preventative measures.

2. Spark plug wire loose 2. Make sure spark wire is securely attached to spark

plug

3. Dirty carburetor 3. Clean carburetor, use gas stabilizer, new gas can, or

purchase carburetor replacement or repair kit per

parts breakdown

4. Carburetor not primed 4. Prime unit 3 more times, squeeze throttle when pull-

ing recoil handle

Engine misses or lacks power 1. Clogged gas tank 1. Remove and clean

2. Clogged air lter 2. Clean or replace

3. Carburetor out of adjustment or bad 3. Call factory or take to authorized repair center

4. Spark plug wet, faulty or improperly gapped 4. Clean, replace or gap spark plug

Engine runs, then quits 1. Gas cap not venting 1. Unscrew the gas cap and then re-tighten gas cap

2. Plugged fuel lter 2. Clean or replace

3. Carburetor out of adjustment or bad 3. Call factory or take to authorized repair center

Engine revs too high 1. Carburetor out of adjustment or air leak in

the intake

1. Call factory or take to authorized repair center

Auger turns at idle 1. Idle speed too high 1. Adjust idle speed lower

2. Broken clutch spring 2. Replace spring

Auger turns, but has no power 1. Choke on 1. Turn o choke after engine is running

2. Carburetor out of adjustment 2. Call factory or take to authorized repair center

3. Broken transmission 3. Call factory or take to authorized repair center

4. Worn clutch shoes 4. Replace clutch shoes and spring

Auger jumps 1. Blade damaged 1. Replace with new blade

Auger cuts slowly 1. Dull blade 1. Replace with new blade

2. Damaged shtail point 2. Replace shtail point

Contact customer service if above remedies fail.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

8, 9

BALLOON #

PART # DESCRIPTIONQTY.

1 154

EARTH AUGER WELDMENT 10 IN RH

2 8980

SHOCK SPRING

EB10A

BLADE EARTH 10INCH CUT AND SHARPENED

EBOLT

BOLT 1/4-28 X 5/8 HH GR5 ZN

5 1423

BOLT 5/16-18 X 2 HH GR5 ZN

WF516

WASHER FLAT 5/16 INCH STANDARD ZN

60G56

NUT-LOC 5/16-18 BI-WAY ZN

ENUT

NUT-LOC 1/4-28 BI-WAY

8958HD

FISH TAIL POINT

10 1151

DECAL AND ART WARNING AUGER ICE AND EARTH

I10

INSERT 10 IN AUGER BOX

12 1433 BOLT 3/8-16 X 1-1/2 HH 1

13 2104

NUT 3/8-16 HLKBW ZN

LBB10P

ASSEMBLY BOX UPC STENCIL EA10F

EA6F

EA2F, EA3F EA4F

EA8F EA10F

AUGER PARTS EXPLOSIONS

REVISIONS

ECN #

REV.

DESCRIPTION

DATE

8682 1

CREATED PRINT

3/8/2011

MDO

BALLOON #

PART # DESCRIPTION

ASSEMBLED/QTY.

553B

WELDMENT 12 INCH EXTENSION

2 1433 BOLT 3/8-16 X 1-1/2 HH 1

3 2104

NUT 3/8-16 HBW GR5 ZN

PARTS TO BE FREE OF

BURRS AND SHARP EDGES

THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS AND REMAINS THE PROPERTY OF ARDISAM INC.

AND IS CONFIDENTIAL. IT IS SUBMITTED AND MAY BE USED ONLY IN CONNECTION WITH ARDISAMS' PROPOSALS

AND/OR ITS CUSTOMERS' ORDERS. IT SHALL NOT BE DISCLOSED TO OTHERS OR COPIED

WITHOUT ARDISAMS'

SPECIFIC WRITTEN CONSENT AND SHALL BE IMMEDIATELY RETURNED UPON REQUEST.

MATERIAL

NAME

TREATMENT

DR BY APPD PRT NO

EXT12

PT WEIGHT

SURFACE AREA

DATE

REVISION

THIRD ANGLE PROJECTION

SEE BILL OF MATERIALS

NONE

697.20

57969.61

12 INCH EXTENSION

MOlsen

MDO 1/19/2011

03/08/2011

SHEET: 1 OF 2

ALL ANGLES ARE DECIMAL DEGREES

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN MILLIMETERS

THREADS CLASS 2

0.0 ± 1.0°

0 ± 2°

ANGLES:

0.000 ± 0.250 MM

0.00 ± 0.75 MM

0.0 ± 2.5 MM

OTHERWISE NOTED:

TOLERANCE UNLESS

EXT12

REVISIONS

ECN #

REV.

DESCRIPTION

DATE

8682 1

ISSUED DRAWING

3/8/2011

MDO

BALLOON #

PART # DESCRIPTION

ASSEMBLED/QTY.

553C

WELDMENT 18 INCH EXTENSION

2 1433 BOLT 3/8-16 X 1-1/2 HH 1

3 2104

NUT 3/8-16 HBW GR5 ZN

PARTS TO BE FREE OF

BURRS AND SHARP EDGES

THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS AND REMAINS THE PROPERTY OF ARDISAM INC.

AND IS CONFIDENTIAL. IT IS SUBMITTED AND MAY BE USED ONLY IN CONNECTION WITH ARDISAMS' PROPOSALS

AND/OR ITS CUSTOMERS' ORDERS. IT SHALL NOT BE DISCLOSED TO OTHERS OR COPIED

WITHOUT ARDISAMS'

SPECIFIC WRITTEN CONSENT AND SHALL BE IMMEDIATELY RETURNED UPON REQUEST.

MATERIAL

NAME

TREATMENT

DR BY APPD PRT NO

EXT18

PT WEIGHT

SURFACE AREA

DATE

REVISION

THIRD ANGLE PROJECTION

SEE BILL OF MATERIALS

NONE

1049.56

81683.44

18 INCH EXTENSION

MOlsen

MDO 1/20/2011

03/30/2011

SHEET: 1 OF 2

ALL ANGLES ARE DECIMAL DEGREES

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN MILLIMETERS

THREADS CLASS 2

0.0 ± 1.0°

0 ± 2°

ANGLES:

0.000 ± 0.250 MM

0.00 ± 0.75 MM

0.0 ± 2.5 MM

OTHERWISE NOTED:

TOLERANCE UNLESS

EXT18

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 17

Operator's Manual

Dually™ Earth Auger Powerhead

AUGER PARTS LIST

KEY

NO.

PART

NO. DESCRIPTION QT Y.

1 1423 BOLTHHCS, 5/1618 X 2”, GRADE 5

(auger shock spring)

2 1433 BOLTHHCS, 3/816 X 11/2”

(auger to powerhead)

3 53684 SHOCK TOP 1PC (used on 6” and 8"

earth augers)

4 60G56 NUTHEX 2WAY REVERSIBLE LOCK

NUT, 5/1618

5 8958HD FISHTAIL POINT used on 4” or larger

earth auger)

6 8970 EARTH POINT (used on 2” & 3” earth

auger)

7 8980 SHOCK SPRING Used on 6" and larger

earth augers)

8 EA2F EARTH AUGER, 2” W/FISHTAIL POINT 1

9 EA3F EARTH AUGER, 3” W/FISHTAIL POINT 1

10 EA4F EARTH AUGER, 4” W/FISHTAIL POINT 1

11 EA6F EARTH AUGER, 6” W/FISHTAIL POINT 1

12 EA8F EARTH AUGER, 8” W/FISHTAIL POINT 1

13 EA10F EARTH AUGER, 10” W/FISHTAIL

POINT

14 EB4 EARTH BLADE, 4” (includes EBOLT &

ENUT)

15 EB6 EARTH BLADE, 6” (includes EBOLT &

ENUT)

16 EB8 EARTH BLADE, 8” (includes EBOLT &

ENUT)

17 EB10 EARTH BLADE, 10” (includes EBOLT

& ENUT)

18 EBOLT BOLTHEX, 1/428 X 5/8”, GRADE 5

(earth blade to auger)

19 ENUT NUTNYLOC, 1/428 2

20 2104 NUT HEX LOCKING, 3/816 2

KEY

NO.

PART

NO. DESCRIPTION QT Y.

21 WF516 WASHERFLAT, 5/16” 2

22 715 SET SCREW 1/420 X 1/4 SCPC BLK

OXIDED

23 8955 BOLT 3/816 X 11/4 SHCS 1

24 EXT12 DEPTH EXTENSION, 12" 1

25 EXT18 DEPTH EXTENSION, 18" 1

ITEMS NOT SHOWN

 EB6HD HEAVY DUTY EARTH BLADE, 6” (in-

cludes EBOLT & ENUT)

 EB8HD HEAVY DUTY EARTH BLADE, 8” (in-

cludes EBOLT & ENUT)

 EB

10HD

HEAVY DUTY EARTH BLADE, 10”

(includes EBOLT & ENUT)

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

DUALLY ENGINE PARTS EXPLOSION

1, 2 1, 2

1, 3, 4, 5, 35

3,4

3, 4, 5, 6

5, 36

5, 7

24, 39

22, 23

16, 17

24, 38

24, 37

22, 31

10, 15

15, 40

11, 30

11, 33

3132

16, 19

22, 27

16, 17, 18

16, 34

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST 19

Operator's Manual

Dually™ Earth Auger Powerhead

DUALLY ENGINE PARTS LIST

KEY

NO. PART NO. DESCRIPTION QT Y.

1 11350 KIT AIR FILTER ASSY SUMMER

2CYCLE VIPER

2 11349 KIT FILTER BLOCK 2CYCLE VIPER 1

3 16892 KIT CARBURETOR REPLACE 1

4 3004114 KIT CARBURETOR REPAIR

43CC/51CC*

5 11205 KIT INTAKE MANIFOLD 1

6 300479 GASKET CARBURETOR 43/51/71

VIPER ENGINE

7 300476 GASKET INTAKE VIPER ENG 1

8 35906 SPARK PLUG, TORCH L7RTC 1

9 11172 ASSY COIL CE 2CYCLE 1

10 300493 STUD BOLT M6X62MM 2

11 11333 KIT ENGINE AND GAS TANK

SHROUDS

12 300430 RECOIL ASSEMBLY W/STANDARD

HANDLE

13 300429 SPACER RECOIL PLATE 2CYCLE

VIPER

14 300491 CUP RECOIL CLUTCH 2CYCLE

VIPER

15 11197 KIT MUFFLER STRAIGHT

EJECTION

16 10683 KIT COMPLETE GAS TANK THREE

TAB

17 3004105 KIT FUEL LINES 1

18 3004103 FUEL FILTER 1

19 11936 GAS CAP COMPLETE 2012 EPA

SELF VENT

20 10929 COVER TOGGLE SWITCH 1

21 300524 SWITCH TOGGLE BARREL M12 1

KEY

NO. PART NO. DESCRIPTION QT Y.

22 11209 KIT FLYWHEEL 1

23 300337 NUT M8 1

24 11235 KIT CLUTCH VIPER 1

25 3004110 MOUNT RING AND SHROUD

43/51.7CC HP

26 300467 PIN LOCATING VIPER ENG 2

27 300338 KEY 1

28 3250 BOLT M5 X 0.8 X 12 PPHMS GR 8.8

29 300335 BOLT M5 X 20 HHPCS 2

30 10887 BOLT M5 X 0.8 MM X 16 MM PH

W/ WASHER

31 10809 BOLT M5 X 20 SHCS GR 8.8 ZN 9

32 11169 BOLT M5 X 28 1

33 300439 BOLT M5 X 20 1

34 300336 BOLT M6 X 1 X 10MM HHF 6

35 300456 BOLT M5 X 50MM W/ WASHER HP

ENGINE

36 300438 BOLT M5 X 25MM WASHER HD 2

37 300450 BOLT SHOULDER CLUTCH ROTOR 2

38 300449 WASHER M8 SPRING ROTOR 2

39 300462 WASHER M8 2

40 300492 NUT M6 X 1.0 HF GR8.8 YL ZN 2

* Carburetor Repair Kit includes: primer bulb,

gaskets, diaphragm and needle.

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Operator's Manual

Dually™ Earth Auger Powerhead

KEY # PART NO. DESCRIPTION QT Y.

1 4844 HANDLEBAR FOAMED DUAL STYLE 1

2 11676 ENGINE 51CC CE VPR CAT HNDLBR MNT 1

3 4819 ASSEMBLY TRIGGER LONG THROW W/

OUT CABLE

4 4814 BOLT 1024 X 11/4 PTHMS ZN FT 2

5 90148 BOLT 1/420 X 3/4 HH GR5 BLK ZN W/

PATCH

6 3004119 TRANSMISSION ASSEMBLY 1

7 10473 CABLE ASSEMBLY TWO INTO ONE 1

8 75300* KIT TOP CASTING 1

9 3004100 CLUTCH DRUM 1

10 8922 BALL BEARING R12 DOUBLE LIP 3

11 9814 GEAR 7T PINION THREADED, 5/8”

THREAD

12 8924 SNAP RING 3

13 8915 DOWEL PIN STEEL 1/4” X 1/2” 2

KEY # PART NO. DESCRIPTION QT Y.

14 8912 GEAR 44T 3/4” HOLE 1

15 8919 GASKET 1

16 8923 BALL BEARING R10 2

17 8914 GEAR 48T HARD 1

18 75600** KIT LOWER CASTING 1

19 8913 SHAFT OUTPUT 7/8” 1

20 8931F BOLT 1/420 X 2 SHCS FT 4

21 8929 BOLT 1/420 X 11/2 SHCS 2

22 9214A GEAR 10T CLUSTER PINION HT 1

23 11468 GREASE EP2 MOLY 1

* The top casting kit (P/N: 75300) includes a gasket (P/N: 8919). It also

includes a shim (P/N: 3004149) that is not needed for the Dually.

** The lower casting kit (P/N: 75600) includes the powerhead transmission

gasket (P/N: 8919), and ball bearings (P/Ns: 8922, 8923).

GREASE

La page charge ...

EarthQuake 10310 Manuel utilisateur

Marque: EarthQuake

Modèle: 10310

Taper: Manuel utilisateur

Ce manuel convient également à

10310 Dually™ Earth Auger Powerhead

Télécharger le PDF

rapport

dans d''autres langues

English: EarthQuake 10310 User manual
español: EarthQuake 10310 Manual de usuario

EarthQuake 10310 Manuel utilisateur

Ce manuel convient également à

EarthQuake 10310 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents