Bosch Power Tools GTS1031 GTA500 Manuel utilisateur

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

For English Version Version française Versión en español

See page 2 Voir page 37 Ver la página 72

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Call Toll Free for Con-

sumer Information

& Service Locations

Pour obtenir des informations

et les adresses de nos centres

de service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

GTS1031

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 1

-2-

“READ ALL INSTRUCTIONS” Failure to follow the safety rules listed below and other basic

safety precautions may result in serious personal injury.

!

WARNING

1:1>-8%-21@E$A81?

);>7>1-

"$ )+

Do not let visitors contact tool or extension cord. All

visitors should be kept away from work area.

")!$$%

Cluttered areas and benches invite accidents.

)!$%!""$!!

With padlocks, master switches.

(! $!'% ($!  &%

Don’t use power tools in damp or wet locations. Keep

work area well lit. Do not expose power tools to rain.

Do not use tool in presence of flammable liquids or

gases.

"1>?;:-8%-21@E

 !)+!'$"!)$&!!

Read and understand the owner’s manual and labels

affixed to the tool. Learn its application and limitations

as well as the specific potential hazards peculiar to

this tool.

! K&!($$

Keep proper footing and balance at all times.

%@-E-81>@Watch what you are doing. Use common

sense. Do not op er ate tool when you are tired. Do

not operate while under medication or while using al-

cohol or other drug.

$%%"$!"$+

Do not wear loose clothing or jewelry. They can be

caught in moving parts. Rubber gloves and non-skid

footwear are recom mended when working outdoors.

Wear protective hair covering to contain long hair.

'%%&+!%

Also face or dust mask if cutting operation is dusty,

and ear plugs during extended periods of operation.

'$ %&&$%!

Prevent body contact with grounded surfaces. For

example: pipes, radiators, ranges, refrigerator enclo-

sures.

%! &&!!$!"!)$%!'$

When not in use, before servicing, when changing

blades, bits, cutters, etc.

"'$% "

In working order, and in proper adjustment and align-

ment.

$!('%& +% )$ %

When not in use, before servicing, when changing

blades, bits, cutters, etc.

(! &%&$& 

Make sure the switch is in the “OFF” position before

plugging in tool.

($%& ! &!!!$&%%& 

Serious injury could occur if the tool is tipped or if the

cutting tool is accidentally contacted. Do not store

materials on or near the tool such that it is necessary

to stand on the tool or its stand to reach them.

"$&%

Before further use of the tool, a guard or other part

that is damaged should be carefully checked to en-

sure that it will operate properly and perform its in-

tended function. Check for alignment of moving

parts, mounting and any other con di tions that may

affect its operation. A guard or other part that is dam-

aged should be properly replaced.

All repairs, electrical or mechanical,

should be attempted only by

trained repairmen. Contact the nearest Bosch

Factory Service Center, Authorized Service Station

or other competent repair service.

Use only Bosch replacement parts;

any others may create a hazard.

Use only accessories that are rec-

ommended by the manufacturer for

your model. Accessories that may be suitable for

one tool, may become hazardous when used on an-

other tool.

&;;8'?1

! K&!$&!!

It will do the job better and safer at the rate for which

it was designed.

'%&$&&!!

Don’t force small tool or attachment to do the job of

a heavy-duty tool. Don’t use tool for purpose not in-

tended — for ex ample; don’t use circular saw for cut-

ting tree limbs or logs.

%'$)!$

Use clamps or a vise to hold work. It’s safer than

using your hand and it frees both hands to operate

the tool.

H%(&% %&$'&! %I

!

WARNING

!

WARNING

!

WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 2

-3-

$&! !

Feed work into a blade or cutter against the direction

of rotation of the blade or cutter only.

($(&!!$'  ' && 

Turn power off. Don’t leave tool until it comes to a

complete stop.

&;;8->1

! !&&$!$%'%&!!

These tools are precision built. Any alteration or

modification not specified is misuse and may result

in dangerous con ditions.

(!%!'%$%

Do not operate electric tools in gaseous or explosive

at mo spheres. Motors in these tools normally spark,

and may re sult in a dangerous condition.

 & &!!%)&$

Keep tools sharp and clean for better and safer

perfor mance. Follow instructions for lubricating and

changing ac cessories. Inspect tool cords periodi-

cally and if damaged, have repaired by authorized

service facility. Inspect ex tension cords periodically

and replace if damaged. Keep handles dry, clean

and free from oil and grease.

Before connecting the tool to a

power source (receptacle, outlet,

etc.), be sure voltage supplied is the same as that

specified on the nameplate of the tool. A power

source with voltage greater than that specified for

the tool can result in serious injury to the user — as

well as damage to the tool. If in doubt, DO NOT

PLUG IN THE TOOL. Using a power source with

voltage less than the nameplate rating is harmful to

the motor.

For your own safety, do not operate

your table saw until it is completely

assembled and installed according to the instruc-

tions … and until you have read and understood the

following:

1. General Safety Rules. . . . . . . . . . . . . . . . . . 2–5

2. Double Insulated Tools . . . . . . . . . . . . . . . . . . . 6

3. Getting To Know Your Table Saw. . . . . . . . 9, 10

4. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 12–16

5. Adjustments . . . . . . . . . . . . . . . . . . . . . . . 17–21

6. Basic Table Saw Operation . . . . . . . . . . . 22–34

7. Maintaining Your Table Saw. . . . . . . . . . . 34–35

%&&+!%)

Your table saw MUST BE BOLTED securely to a

stand or workbench. In addition, if there is any ten-

dency for the table saw to tip over or move during

certain operations such as cutting long, heavy

boards, use an auxiliary support.

!&!

Use the table saw in a well lit area and on a level

surface, clean and smooth enough to reduce the risk

of trips and falls. Use it where neither the operator

nor the casual observer is forced to stand in line with

the blade.



Kickbacks can cause serious injury: A “KICKBACK”

occurs when a part of the workpiece binds between

the sawblade and the rip fence or other fixed object.

Workpiece binding the blade due to misalignment,

can also cause kickback. During kickback, work-

piece rises from table and is thrown toward the op-

erator. Keep your face and body to one side of the

sawblade, out of line with a possible “KICKBACK”.

% "!%% '$+

'%'+(!+

- Maintaining the rip fence parallel to the sawblade.

.Keeping the sawblade sharp. Replacing or sharp-

ening anti-kickback pawls when points become dull.

/Keeping sawblade guard, spreader and anti-kick-

back pawls in place and operating properly. The

spreader must be in alignment with the sawblade

and the pawls must stop a kickback once it has

started. Check their action before ripping.

0NOT ripping workpiece that is twisted or warped

or does not have a straight edge to guide along the

rip fence.

1NOT releasing work until you have pushed it all

the way past the sawblade.

2Using a Push Stick for ripping widths of 2" to 6"

and an auxiliary fence and Push Block for ripping

widths narrower than 2" (See “Basic Saw Operation,

Using The Rip Fence” section, pages 29, 30).

3NOT confining the cut-off piece when ripping or

cross cutting.

4When ripping, apply the feed force to the section

of the workpiece between the sawblade and the rip

fence. Use Push Stick or Push Block when appro-

priate (See item f. above).

H%(&% %&$'&! %I

005@5;:-8%-21@E$A81?

!

WARNING

!

WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 3

-4-

"$!&&! 

Eyes, hands, face, ears and body.

&!(! "'

 &!&%"  &!!

! !&)$;;?15@@5:38;B1?

;;?18;@45:3

 1/7@511C18>E

!&! $

$!! %(%!(

!)%

-If any part of your saw is missing, malfunctioning,

has been damaged or broken … such as the motor

switch, or other operating control, a safety device or

the power cord … cease operating immediately until

the particular part is properly repaired or replaced.

.Wear safety goggles and a face shield if operation

is dusty. Wear ear plugs or muffs during extended

periods of operation. Small loose pieces of wood or

other objects that contact the rear of the revolving

blade can be thrown back at the operator at exces-

sive speed. This can usually be avoided by keeping

the guard and spreader in place for all “THRU-SAW-

ING” operations (sawing entirely thru the work) AND

by removing all loose pieces from the table with a

long stick of wood IMMEDIATELY after they are cut

off.

/Use extra caution when the guard assembly is re-

moved for resawing, dadoing, rabbeting or molding

— replace the guard as soon as that operation is

completed.

0NEVER turn the saw “ON” before clearing the

table of all tools, wood scraps, etc., except the work-

piece and related feed or support devices for the op-

eration planned.

1NEVER place your face or body in line with the

cutting tool.

GNEVER place your fingers and hands in the path of

the sawblade or other cutting tool.

GNEVER reach in back of the cutting tool with either

hand to hold down or support the workpiece, remove

wood scraps, or for any other reason. Avoid awkward

operations and hand positions where sudden slip

could cause fingers or hand to move into a sawblade

or other cutting tool.

GDO NOT perform any operation “FREEHAND” —

always use either the rip fence or the miter gauge to

position and guide the work.

GNEVER use the rip fence when crosscutting or the

miter gauge when ripping. DO NOT use the rip fence

as a length stop.

GNEVER hold onto or touch the “free end” of the

workpiece or a “free piece” that is cut off, while power

is “ON” and/or the sawblade is rotating.

GShut “OFF” the saw and disconnect the power cord

when removing the table insert, changing the cutting

tool, removing or replacing the blade guard, or mak-

ing adjustments.

GProvide adequate support to the rear and sides of

the saw table for wider or long workpieces.

GPlastic and composition (like hardboard) materials

may be cut on your saw. However, since these are

usually quite hard and slippery, the anti-kickback

pawls may not stop a kick back. Therefore, be espe-

cially attentive to following proper set-up and cutting

procedures for ripping. Do not stand, or permit any-

one else to stand, in line with a potential kickback.

2 If you stall or jam the sawblade in the workpiece,

turn saw “OFF”, remove the workpiece from the saw-

blade, and check to see if the sawblade is parallel to

the table slots or grooves and if the spreader is in

proper alignment with the sawblade. If ripping at the

time, check to see if rip fence is parallel with the saw-

blade. Readjust as indicated.

3NEVER gang crosscut — lining up more than one

work piece in front of the blade (stacked vertically, or

horizontally outward on the table) and then pushing

thru sawblade. The blade could pick up one or more

pieces and cause a binding or loss of control and

possible injury.

4DO NOT remove small pieces of cut-off material

that may become trapped inside the blade guard

while the saw is running. This could endanger your

hands or cause a kick back. Turn saw “OFF” and wait

until blade stops.

5Do not reach beyond table saw base. Keep your

hands away from spinning blade.

 !)+!'$'&& &!!%

Dull, gummy or improperly sharpened or set cutting

tools can cause material to stick, jam, stall the saw,

or kickback at the operator. Minimize potential injury

by proper cutting tool and machine maintenance.

NEVER ATTEMPT TO FREE A STALLED SAW-

BLADE WITHOUT FIRST TURNING THE SAW

OFF.

H%(&% %&$'&! %I

005@5;:-8%-21@E$A81?

!

WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 4

-5-

H%(&% %&$'&! %I

- NEVER use grinding wheels, abrasive cut-off

wheels, fric tion wheels (metal slitting blades) wire

wheels or buffing wheels.

.USE ONLY RECOMMENDED ACCESSORIES.

/Crosscutting operations are more conveniently

worked and with greater safety if an auxiliary wood

facing is attached to the miter gauge. (See Page 26).

0Make sure the top of the cutting tool rotates toward

you when standing in normal operating position. Also

make sure the cutting tool, arbor collars and arbor

nut are installed pro p erly. Keep the cutting tool as low

as possible for the oper ation being performed. Keep

all guards in place whenever possible.

GDo not use any blade or other cutting tool marked

for an operating speed less than 5000 R.P.M. Never

use a cutting tool larger in diameter than the diameter

for which the saw was designed. For greatest safety

and efficiency when rip ping, use the maximum diam-

eter blade for which the saw is designed, since under

these conditions the spreader is near est the blade.

1Make sure the table insert is flush or slightly below

the table surface on all sides except for rear side.

NEVER oper ate the saw unless the proper insert is

installed.

& %&+

SAFETY IS A COMBINATION OF OPERATOR

COMMON SENSE AND ALERTNESS AT ALL

TIMES WHEN THE TABLE SAW IS BEING USED.

Do not allow familiarity (gained from fre quent use of

your table saw) to become com -

mon place. Always remember that

a careless fraction of a second is sufficient to inflict

severe injury.

The operation of

any power tool

can result in for-

eign objects being

thrown into the

eyes, which can

result in severe

eye damage. Al-

ways wear safety

goggles that com-

ply with ANSI Z87.1 (shown on pack age) before

commencing power tool operation.

%;91 0A?@ />1-@10 .E <;C1>

?-:05:3 ?-C5:3 3>5:05:3

0>5885:3 -:0 ;@41> /;:?@>A/@5;: -/@5B5@51?

/;:@-5:? /4195/-8? 7:;C: @; /-A?1 /-:/1>

.5>@40121/@?;>;@41>>1<>;0A/@5B14->9%;91

1D-9<81?;2@41?1/4195/-8?->1

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other

masonry products, and

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to filter out microscopic particles.

!& !!)%&+ %&$'&! %

&&""$! &$! &!+!'$

&%)

005@5;:-8%-21@E$A81?

WARNING

Wear Eye Protection



!

WARNING

!

WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 5

-6-

;A.81:?A8-@10&;;8?

Double insulation is a design concept used in

electric power tools which eliminates the need for

the three wire grounded power cord and grounded

power supply system. It is a recognized and ap-

proved system by Underwriter’s Laboratories, CSA

and Federal OSHA authorities.

"!$& & Servicing of a tool with double insu-

lation requires care and knowledge of the system

and should be performed only by a qualified service

technician.

WHEN SERVICING, USE ONLY IDENTICAL RE-

PLACEMENT PARTS.

POLARIZED PLUGS. To reduce the risk of electri-

cal shock, your tool is equipped with a polarized plug

(one blade is wider than the other), this plug will fit

in a polarized outlet only one way. If the plug does

not fit fully in the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to install the

proper outlet. To reduce the risk of electrical shock,

do not change the plug in any way.

*& %! !$%

Replace damaged cords immedi-

ately. Use of damaged cords can

shock, burn or electrocute.

If an extension cord is necessary, a

cord with adequate size conductors

should be used to prevent excessive voltage drop,

loss of power or overheating. The table shows the

correct size to use, depending on cord length and

nameplate amperage rating of tool. If in doubt, use

the next heavier gauge. Always use U.L. and CSA

listed extension cords.

$! %,%!*& %! !$%

(!&&$ & '$$ &&!!%

NOTE: The smaller the gauge number, the heavier

the cord.

&;;8K?

9<1>1

$-@5:3

;>0%5F15:)

)5>1%5F1?5:99



3-6

6-8

8-10

10-12

12-16

18 16 16 14 0.75 0.75 1.5 2.5

18 16 14 12 0.75 1.0 2.5 4.0

16 16 14 12 1.0 2.5 4.0 —

14 12 — — — — — —

25 50 100 150 15 30 60 120

;>01:3@45:11@ ;>01:3@45:1@1>?

&-.81;2;:@1:@?

Page

General Safety Rules . . . . . . . . . . . . . . . . . . . . .2

Additional Safety Rules . . . . . . . . . . . . . . . . .3–5

Double Insulated Tools & Extension Cords . . . .6

Table of Contents . . . . . . . . . . . . . . . . . . . . . .6-7

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . .7-8

Tools Needed For Assembly . . . . . . . . . . . . . . .8

Getting To Know Your Table Saw . . . . . . . . .9, 10

Power Switch . . . . . . . . . . . . . . . . . . . . . . . . .9

Elevation Wheel . . . . . . . . . . . . . . . . . . . . . .9

Blade Bevel Lock Handle . . . . . . . . . . . . . . .9

Blade Bevel Scale . . . . . . . . . . . . . . . . . . . . .9

Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Table Extension Lock Handle . . . . . . . . . . . .9

Push Stick . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Table Extension . . . . . . . . . . . . . . . . . . . . . . .9

Rip Fence . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Rip Fence Scale . . . . . . . . . . . . . . . . . . . . . .9

Smart Guard System . . . . . . . . . . . . . . . . . .9

Page

Table Insert . . . . . . . . . . . . . . . . . . . . . . . . . .9

Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Miter Gauge . . . . . . . . . . . . . . . . . . . . . . . . .10

Cord Wrap . . . . . . . . . . . . . . . . . . . . . . . . . .10

Rip Fence Storage . . . . . . . . . . . . . . . . . . .10

Push Stick & Wrench Storage . . . . . . . . . .10

One-Handed Carry Handle . . . . . . . . . . . . .10

Smart Guard System Storage . . . . . . . . . .10

Dust Port/Vacuum Hook-Up . . . . . . . . . . . .10

Anti-Kickback Device Storage . . . . . . . . . .10

Miter Gauge Storage . . . . . . . . . . . . . . . . . .10

Hex Wrench & Storage compartment . . . .10

Stand Attachment Bracket . . . . . . . . . . . . .10

Unpacking and Checking Contents . . . . . . . . .11

Table of Loose Parts . . . . . . . . . . . . . . . . . .11

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . .12–16

Attaching Smart Guard

System Components . . . . . . . . . . . . . .12, 13

H%(&% %&$'&! %I

!

WARNING

!

WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 6

-7-

Page

Changing The Blade . . . . . . . . . . . . . . .14-15

Attaching The Rip Fence for Use

& Storage . . . . . . . . . . . . . . . . . . . . . . . . . .16

Mounting Table Saw to Workbench . . . . . . . . .16

Adjustments . . . . . . . . . . . . . . . . . . . . . . . .17–21

Adjusting 0 & 45 Degree Positive Stops . . .17

Adjusting Blade Parallel to the

Slot Miter Gauge . . . . . . . . . . . . . . . . . . . . .18

Aligning Rip Fence . . . . . . . . . . . . . . . . . . .19

Rip Fence Pointer Adjustment . . . . . . . . . .19

Table Pointer Adjustment . . . . . . . . . . . . . .20

Adjusting Riving Knife . . . . . . . . . . . . . .20-21

Adjusting Table insert . . . . . . . . . . . . . . . . .21

Basic Table Saw Operation . . . . . . . . . . . .22–34

Safety Power Switch . . . . . . . . . . . . . . . . . .22

Smart Guard System . . . . . . . . . . . . . .22, 23

Blade Bevel Control . . . . . . . . . . . . . . . . . .24

Extending Table Extension . . . . . . . . . . . . .24

Using Rip Fence Pointer . . . . . . . . . . . . . . .24

Page

Using Table Pointer . . . . . . . . . . . . . . . . . . .24

Work Helpers . . . . . . . . . . . . . . . . . . . . . . . .25

Using the Miter Gauge . . . . . . . . . . . . . . . .26

Crosscutting . . . . . . . . . . . . . . . . . . . . . . . .27

Repetitive Crosscutting . . . . . . . . . . . . . . . .28

Miter Cutting . . . . . . . . . . . . . . . . . . . . . . . .28

Bevel Crosscutting . . . . . . . . . . . . . . . . . . .28

Compound Miter Cutting . . . . . . . . . . . . . . .28

Using the Rip Fence . . . . . . . . . . . . . . .29, 31

Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Non Thru-Sawing . . . . . . . . . . . . . . . . . . . .31

Rabbeting . . . . . . . . . . . . . . . . . . . . . . . . . .31

Dadoing Cutting . . . . . . . . . . . . . . . . . . .32-33

Maintaining Your Table Saw . . . . . . . . . . . . . . .34

Clearing Dust Chute/ Scoop . . . . . . . . . . . .34

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . .35

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . .36

8;??->E;2&1>9?

)!$"

The item on which the cutting operation is being per-

formed. The surfaces of a workpiece are commonly

referred to as faces, ends and edges.

 &")%

Device which, when properly maintained, is de-

signed to stop the workpiece from being kicked back

at the operator during operation.

$!$

The shaft on which a cutting tool is mounted.

(

Blade angle relative to the table surface.

$!%%'&

A cutting or shaping operation made across the

width of the workpiece cutting the workpiece to

length.

!

A non-through cut which produces a square sided

notch or trough in the workpiece.

&$!$

A device which can help guide workpieces during rip

type operation by keeping workpiece in contact with

the rip fence. It also helps prevent kickback.

$ 

Performing a cut without a fence, miter gauge, fix-

ture, hold down or other proper device to keep the

workpiece from twisting during the cut.

'

A sticky, sap-based residue from wood products.

After it has hardened, it is referred to as “RESIN”.



Misalignment of the blade which causes the trailing

or out feed side of the blade to contact the cut sur-

face of the work piece. Heel can cause kickback,

binding, excessive force, burning of the workpiece

or splintering. In general, heel cre ates a poor quality

cut and can be a safety hazard.

$

The space in the workpiece where the material was

removed by the blade.



An uncontrolled grabbing and throwing of the work-

piece back toward the front of the saw during a rip

type operation.

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 7

-8-

  

The end of the workpiece which, during a rip type

operation, is pushed into the cutting tool first.

! 

A non-through cut which produces a special shape

in the workpiece used for joining or decoration.

! &$'%) 

Any cutting operation where the blade does not ex-

tend through the workpiece (e.g. Dado, Rabbet).

"'%%&

A device used to feed the workpiece through the

saw during narrow ripping-type operation and helps

keep the operator’s hands well away from the blade.

Use the Push Stick for rip widths less than 6 inches

and more than 2 inches.

"'%!

A device used for ripping-type operations too narrow

to allow use of a Push Stick. Use a Push Block for

rip widths less than 2 inches.

$&

A notch in the edge of a workpiece. Also called an

edge dado.

$"" 

A cutting operation along the length of the workpiece

cutting the workpiece to width.

$(!'&! %"$ '&$"

The number of turns completed by a spinning object

in one minute.

Disconnect plug from power source before performing any assembly, adjustment or repair

to avoid possible injury.

!

WARNING

COMBINATION SQUARE

PHILLIPS SCREWDRIVER

HEX “L” WRENCH

(Supplied-Tool Adjustment)

5 MM

SHOULD BE NO GAP OR OVERLAP

HERE WHEN SQUARE IS FLIPPED

OVER IN DOTTED POSITION.

COMBINATION SQUARE MUST BE TRUE

DRAW LIGHT LINE ON

BOARD ALONG THIS EDGE.

STRAIGHT EDGE OF BOARD

3/4" THICK. THIS EDGE

MUST BE PERFECTLY

STRAIGHT.

&;;8? 11010;>??19.8E:006A?@91:@

HEX “L” WRENCH

(Supplied-Insert Plate)

2 MM

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 8

-9-

1@@5:3&;:;C+;A>&-.81%-C

"!)$%)&

Switch incorporates hole for use with padlock to pre-

vent accidental starting.

(&! )

Elevates or lowers the blade. Also used to tilt the

blade 0 to 45 degrees.

(! 

Locks the blade to de sired bevel angle.

(%

Shows the degree the blade is tilted.

%

Supports table saw. Holes are provided in base to

bolt the saw to a workbench or stand. Includes inte-

grated carry and adjustment handles

&*& %! ! 

Allows you to lock the table extension at desired dis-

tances. Also prevents use of table saw with un-

locked extension.

"'%%&

Allows you to rip smaller pieces of stock with a

greater level of safety.

&*& %!

Provides a larger work surface for wider workpieces.

$" 

Exclusive Self-Aligning, Squarelock rip fence can be

easily moved or locked in place by simply raising or

lowering lock handle.

$" %

Shows the distance from the blade to rip fence

through a convenient viewing and magnifying win-

dow. Lower portion of scale can be used up to 10

inches. Upper portion of scale is used for cuts be-

yond 10 inches.

%$&'$%+%&

Consists of three key elements: Adjustable (3 posi-

tion) Riving Knife, Anti-Kickback Device, and Barrier

Guard Device. All of these are part of a modular sys-

tem that requires no tools to assemble or unassem-

ble. This Guard System must always be in place and

working properly for all thru-sawing cuts.

& %$&

Removable for removing or installing blade or other

cutting tools.

12

13

54

3

8

6

24

10

14

FIG. 1

15

9

11

7

12

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 9

-10-

&

Provides large working surface to support work-

piece.

&$'

Head can be locked in desired position for crosscut-

ting or mitering by tightening the lock knob. ALWAYS

SECURELY LOCK IT WHEN IN USE.

!$)$"

Allows you to easily secure the cord so it’s out of the

way when transporting or storing.

$" %&!$

Conveniently stores rip fence when not in use.

"'%%&)$ J%&!$

Allows you to store Push-stick and arbor wrenches

(2).

!  $$+ 

Optimized position to carry tool at side with one

hand.

%$&'$%+%&%&!$

When not in use, the Main Barrier Guard Device can

be stored on the right side of the saw, underneath

the table. The Anti-kickback Device stores just

above the Dust Chute on the back of the tool.

'%&"!$&(''!!'"

Removable; to clear large pieces of wood trapped

inside. Always check to ensure dust port is securely

fastened to table saw before use. Attach 2-1/4” vac-

uum hose into dust port for convenient sawdust re-

moval. An adaptor is available for use with alternate

hose sizes.

 &( %&!$

Conveniently stores Anti-Kickback Device when not

in use.

&$'%&!$

Conveniently stores miter gauge when not in use.

*)$ %&!$!"$& &

Hex wrench for removing lower dust chute and ad-

justing various hex heads on the saw.

%& && &$&

Quick connect attachment point for folding leg table

saw stand.

1@@5:3&;:;C+;A>&-.81%-C

FIG. 2

16

22

21

19

20

18

17

23

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 10

-11-

':<-/75:3:041/75:3;:@1:@?

To avoid injury from unexpected

starting or electrical shock during

unpacking and setting up, do not plug the power

cord into a source of power. This cord must remain

unplugged whenever you are working on the table

saw.

Model GTS1031 Table Saw is shipped complete in

one carton.

Separate all parts from packing materials and check

each one with the illus tration and the list of Loose

Parts to make certain all items are accounted for

before discarding any packing material (Fig. 3).

If any parts are missing, do not

attempt to assemble the table saw,

plug in the power cord or turn the switch on until the

missing parts are obtained and are installed

correctly.

&!!!%"$&%

ITEM DESCRIPTION QTY.

1 Table Saw Assembly 1

2 Rip Fence 1

3 Table Insert 1

4 Barrier Guard Assembly 1

5 Anti-Kickback Device 1

6 Miter Gauge 1

7 Push Stick 1

!&Cut cable tie  (for shipping purpose only)

located between the saw base and under carriage

(Fig. 4). You may cause damage to the blade

elevation system if trying to raise blade if cable tie is

not removed.

!

WARNING

!

WARNING

FIG. 3

6

5

4

1

2

7

3

FIG. 4

8

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 11

-12-

??19.8E

&& &%$&'$%+%&

To prevent personal injury, always

dis con nect plug from power source

before attaching or removing the Smart Guard

System.

"!%&!  &$(  

1. Remove table insert using finger hole.

2. Raise the blade as high as it will go and set it per-

pendicular to table (0° on bevel scale) (Fig. 5).

3. Rotate the riving knife release lever  clockwise,

so that it points upward (Fig. 5).

4. Pull riving knife  towards release lever to disen-

gage it from the pins .

5. Slide the riving knife  up to its highest position,

so that it is directly over the center of the blade

(Fig. 6).

6. Align holes in riving knife with pins  and lock the

release lever  by rotating it counterclockwise.

Push/pull riving knife to verify that it is locked in

place (Fig. 6).

7. Replace table insert (Fig. 7).

&& &'$%%+

8. With one hand, hold the front of the barrier

guard assembly  by the metal “fork”. With the

other hand, hold the guard release lever  up

(Fig. 7).

9. Lower the rear of guard assembly and slip the

cross bar  into the rear notch  on top of the

riving knife  (Fig. 7).

!

WARNING

FIG. 5

FIG. 6

1

2

1

3

2

FIG. 7

4

5

7

6

2

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 12

-13-

10. Lower the front of the guard assembly  until

the metal “fork” is parallel with the table (Fig. 8).

11. Press down on the guard release lever  until

you feel and hear it snap into the locking posi-

tion. Check that the guard assembly is securely

connected (Fig. 8).

&& & &(

12. Attach the Anti-Kickback Device  into the flat re-

cessed area  of the riving knife  (Fig. 9).

13. Squeeze the compression pads  while nesting

the device into the flat area (Fig. 9).

14. Release the compression pads such that the

Anti-Kickback Device locks onto the riving knife

immediately behind the guard assembly. Check

that the attachment pin is securely connected

into locking hole. Carefully raise and lower the

pawls  – when letting go, the spring-loaded

pawls must come down and contact the table in-

sert (Fig. 9).

5:@ Position the Anti-Kickback Device behind the flat

recessed area and slide it towards the front until it

drops into the recessed area – then release the com-

pression pins.

;@1 The two attachments are independant of each

other, so the Anti-Kickback Device can be attached

before the Guard Assembly.

FIG. 8

4

5

FIG. 9

7

9

10

8

2

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 13

-14-

Disconnect plug from power

source before performing any as-

sembly, adjustment or repair to avoid possible injury.

'% &!$$&

"!$& & The saw blade provided on this tool

has a carbide-tipped kerf width of .102” and a plate

(body) thickness that is .071” thick. When looking for

a replacement blade, select one with dimensions

close to the original blade. This information may not

be printed on the blades packaging. If not, check the

manufacturers catalog or website. Bosch offers an

extensive line of Premium-Quality Professional Saw

Blades that match the requirements for this tool. You

must select a blade with a kerf width of .092” or more

and a plate (body) thickness .088” or less (Fig. 10).

&;>10A/1@41>5?7;25:6A>E0;

:;@ A?1 1D@>- @45: 71>2 ?-C

.8-01? The kerf of the blade must be wider than

.092”. Extra thin kerf saw blades (less than .092”)

may cause the work piece to bind against the riving

knife during cutting. It is recommended that the kerf

of the replacement blade used on this saw be .092”

or more.

&;>10A/1@41>5?7;25:6A>E0;

:;@A?1?-C.8-01?9-01C5@4-

@45/7.;0E<8-@1 If the replacement saw blade's

plate thickness is greater than .088”, the riving knife

would not properly serve as an aid to reduce kick-

back. The replacement blade's plate thickness must

be less than .088”.

&;>10A/1@41>5?7;25:6A>E0;

:;@ A?1 .8-01 H0-9<1:1>?I

[email protected]85F1>?I ;> H?@5221:5:3 /;88->?I ;: .;@4

?501?;2->1<8-/191:@.8-01 These are metal

plates positioned against the sides of the blade to

reduce deflection that may occur when using thin

saw blades. Use of these devices on both sides will

prevent the blade from being properly aligned with

the riving knife, which may bind the work piece dur-

ing cutting. One “stabilizer” plate may be placed only

against the outside of a thin replacement blade.

These plates are not required with the supplied

Bosch blade.

!

WARNING

!

WARNING

!

WARNING

!

WARNING

FIG. 10







FIG. 11

$!(  %&&! !&

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 14

  &

!& Clean blade of any excess oil before

installation.

1. Remove the table insert  (Fig. 11).

2. Raise the blade  to the maximum height by turn-

ing the control wheel  counterclockwise (Fig. 11).

3. Remove the arbor nut  and flange  (Fig. 12).

4. To loosen the arbor nut , use the open-end

wrench  and align the wrench jaws on the flats

of the flange to keep the arbor from turning. Place

the box-end wrench  on the arbor nut  and turn

counter-clockwise (to the front of the saw table)

(Fig. 13).

5. Clean any sawdust from both blade collars before

installing the blade. Install a 10" (25.4 cm) blade.

Install the saw blade onto the arbor with the blade

teeth pointing toward the front of the saw.

To avoid injury, do not use a blade larger or smaller

than 10" diameter and 5/8" arbor.

6. Install the flange  against the blade  and thread

the arbor nut  as far as possible by hand. Ensure

that the blade is flush against the inner blade

flange  (Fig. 12).

7. To tighten the arbor nut , use the open-end

wrench  and align the wrench jaws on the flats

of the flange to keep the arbor from turning. Place

the box-end wrench  on the arbor nut  and turn

clockwise (to the rear of the saw table) (Fig. 13).

8. Install the table insert  in the table recess.

(Figure 11).

To avoid injury from a thrown workpiece, blade part,

or blade contact, never operate the saw without the

proper insert in place. Use the table insert when

sawing. Use the dado insert when using a dado

blade.

'% $&""%

Handle carbide-tipped blades carefully. Carbide is

very brittle and can be easily damaged. Use caution

when you install, use or store the blades. Do not use

a carbide-tipped blade that is bent or has bent teeth,

or if the blade has cracks, is broken, or has

missing/loose carbide tips. Do not operate a carbide-

tipped blade faster than its recommended speed.

Read, understand and follow all warnings and in-

structions provided with your carbide-tipped

blades.

&& $" !$'%

 %&!$

1. Raise rip fence handle , so holding clamp is

out far enough to fit on the table and into “V”

groove located on the back of rear rail (Fig. 14).

2. Position the rip fence  over table  holding up the

front end, first engage holding clamp  with rear

rail.

3. Lower front end onto front rail .

4. Lower rip fence handle to lock.

;@1To store rip fence follow same procedure as

above under the table (Fig. 15).

-15-

FIG. 13







FIG. 12







BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 15

-16-

!' & &&%)

If table saw is to be used in a permanent location, it

should be fastened securely to a firm supporting sur-

face such as a stand or workbench, using the four

mounting holes  (Fig. 16).

1. If mounting to a workbench, the base should be

bolted securely using 1/4" hex bolts (not included)

through mounting holes .

5:@ If workbench is 3/4” thick, bolts will have to

be at least 3-1/2” long - if workbench is 1-1/2”

thick, bolts should be at least 4-1/2” long.

2. Locate and mark where the saw is to be mounted,

relative to holes in the base of the tool.

3. Drill four (4) 3/8" diameter holes through work-

bench.

4. Place table saw on workbench aligning holes in

base with holes drilled in workbench.

5. Insert four (4) 1/4" dia. bolts through holes in base

and supporting surface; then secure with (4) 1/4”

flat washers and (4) 1/4" hex nuts.

1

2

3

2

4

1

5

FIG. 14

6

FIG. 16

FIG. 15

RIP FENCE

STORAGE

1/4” HEX BOLT,

WASHER &

HEX NUT

X4

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 16

-17-

'%&  $

"!%&(%&!"%

Your saw is equipped with positive stops for fast and

ac curate positioning of the saw blade at 90 and 45

degrees to the table.

&; <>1B1:@ <1>?;:-85:6A>E -8

C-E? 05?/;::1/@ <8A3 2>;9

<;C1>?;A>/1C41:9-75:3-06A?@91:@?

1. Turn elevation wheel  clockwise and raise blade

to maxi mum height (Fig. 17).

'%& $"!%&(%&!"

2. Loosen the blade tilt lock handle  and push the

elevation wheel  to the left as far as possible

and tighten the blade tilt lock handle (Fig. 17).

3. Place a combination square on the table with one

end of square against the blade as shown (Fig.

18), and check to see if the blade is 90 degrees

to the table. If the blade is not 90 degrees to the

table, loosen the blade tilt lock handle , loosen

90 degree adjustment screw , loosen 90 degree

bevel stop cam  and push the elevation wheel

until the blade is 90 degrees to the table.

4. Tighten blade tilt lock handle , rotate the bevel

stop cam  until it touches the bevel stop housing

, then tighten 90 degree adjustment screw .

5. Loosen adjustment screw  and adjust pointer 

to indicate 0 degrees on the bevel scale.

'%& $"!%&(%&!"

6. Loosen the blade tilt lock handle  and push the

elevation wheel  to the right as far as possible

and tighten the blade tilt lock handle .

7. Place a combination square on the table with one

end of square against the blade as shown

(Fig. 19), and check to see if the blade is 45

degrees to the table. If the blade is not 45 degrees

to the table, loosen the blade tilt lock handle ,

loosen 45 degree adjustment screw , loosen 45

degree bevel stop cam  and push the elevation

wheel until the blade is 45 degrees to the table.

8. Tighten blade tilt lock handle , rotate the 45 de-

gree bevel stop cam  until it touches the bevel

stop housing , then tighten 45 degree adjust-

ment screw .

;@1Your GTS1031 is able to achieve a bevel up

to 47 degrees left and -2 degrees right. To reach

these points, follow the procedure above and reset

stops as needed.

06A?@91:@?

!

WARNING

8

9

FIG. 17

2

4

3

6

5

7

FIG. 18

FIG. 19

1

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 17

-18-

'%& "$&!

&&$'%!&%

The blade was adjusted parallel to the miter gauge

slots at the factory. In order to insure accurate cuts

and help prevent kickback, this adjustment should

be rechecked. If adjustment is necessary, follow

the steps below.

&;<>1B1:@<1>?;:-85:6A>E-8

C-E?05?/;::1/@@41<8A32>;9

<;C1>?;A>/1.12;>19-75:3-:E-06A?@91:@?

1. Turn elevation wheel and raise blade as high as

it will go.

2. Select a point on the body of the saw blade that

is set to the left when viewing blade from the

front of saw, and mark  with a pencil (Fig. 20).

3. Place the base of a combination square against

the edge of the miter gauge slot, and extend the

sliding rule of square so it just touches the

marked point  on the body of the saw blade at

the rear of the table.

4. Rotate blade and check the same marked point

 of the saw blade at the front of the table (Fig. 20).

5. If the front and back measurements, shown in

Figure 20, are not identical, loosen the four

alignment bolts , located on the underside of

the table at the front and rear of the saw with

hex wrench supplied with your saw (Fig. 21 &

22). Carefully move the saw blade until the

blade is parallel to the miter gauge slot, and se-

curely tighten all four bolts.

!

WARNING

FIG. 20

1

FIG. 21

UNDER FRONT

OF TABLE

2

FIG. 22

UNDER REAR OF TABLE

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 18

-19-

  $" 

To prevent personal injury, always

dis con nect plug from power source

before making any adjustments. The rip fence must

be parallel with the SAWBLADE in order to prevent

KICKBACK when ripping.

Your table saw is equipped with a Self-Aligning,

Squarelock™ rip fence. Once the adjustments

below have been made, the rip fence will self align

when the fence is locked into position.

!&The blade must be parallel with the miter

gauge slots (see page 18) and be perpendicular to

table before proceeding with rip fence alignment.

To prevent personal injury, always

make sure the rip fence is locked

before making rip cuts.

1. Lift both guard barriers  to their up locked posi-

tion.

2. Raise lock handle  and slide fence until it is

alongside the sawblade, by lifting right side pawl

 above fence (Fig. 23).

The fence should touch the blade teeth at the

front and rear of the blade. If fence does not touch

the teeth at front and rear of blade continue with

the following the steps:

3. Loosen the two screws  on the top front section

of the rip fence using the included 5mm hex

wrench.

4. Move fence  until it touches the teeth and is

parallel to the blade.

5. Hold fence in place and lower lock handle, check

to make sure the fence stayed parallel to the

blade then tighten screws (Fig. 23).

6. Clamp rip fence to check if it holds securely at

front and rear. If rear is not clamped securely, un-

clamp fence and turn rear clamp adjustment

screw  clockwise for increased clamp ing. Try

clamping the fence to verify if it self aligns and

clamps tightly at the front and rear. Overtightening

of the rear clamp adjustment screw  will cause

the rip fence to be non-self aligning (Fig. 23).

Overtightening may cause friction or “chatter”

when fence is moved side to side.

$" "! &$'%& &

The distance of the rip fence body from the blade

when ripping on the right side of the blade is deter-

mined by lining the pointer  with the desired dimen-

sion on the scale (Fig. 24).

&!%&&$" "! &$

1. Lift both guard barriers  to their up locked posi-

tion (Fig. 23).

2. Raise lock handle and slide fence until it is

alongside the sawblade, by lifting right side pawl

 above fence. Lock fence in place (Fig. 23).

3. Loosen pointer adjustment screw , adjust pointer

 to “0” mark on lower scale , then re-tighten

screw (Fig. 24).

3

2

5

6

4

FIG. 23

1

7

8

9

FIG. 24

!

WARNING

!

WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 19

-20-

&"! &$'%& &

If an adjustment to the table pointer is necessary,

loosen pointer ad justment screw , adjust pointer

 and tighten screw  (Fig. 25).

The table pointer should always be adjusted

relative to fence pointer.

1. Adjust fence pointer to (zero) - see “Rip Fence

Pointer Adjustment”.

2. Make sure the table is in the closed position and

slide fence to the right until the fence pointer is

at 10”. (Note: A portion of the fence will be off

the rail.)

3. Look at fence pointer and note 10” on lower

scale.

4. Adjust the table pointer  to the same reading

on upper scale as that shown on the fence

pointer. Both pointers must agree when fence is

at this position.

$(    &

"!$& & The Riving Knife  must always be

in line with the Saw Blade . The Riving Knife  is

thinner than the width of the Kerf  by approxi-

mately five thicknesses of paper  on each side,

depending on the thickness of paper used

(Fig 26). ;@1 The Kerf is the width of the cut

made by the teeth on the saw blade.

To prevent personal injury, always

disconnect plug from power

source before making any adjustments and when

attaching or removing the Smart Guard System.

 $(    &

!& The Riving Knife has been properly aligned

at the factory - Check the alignment before making

any adjustments.

1. Raise the Saw Blade to maximum height and set

the bevel angle to 0°.

2. Remove the Barrier Guard Assembly and Anti-

Kickback Device (see manual).

3. Place the Rip Fence  on the right side and slide

it until it touches the tips of the Saw Blade  - Lock

fence.

4. Check the alignment:

A. From the top, look down over the Fence and

check that the Riving Knife is in line (front to

back) with the blade and parallel with the fence.

B. Slide the fence away from the blade. Look over

the front of the blade and check that the Riving

Knife is in line with the blade.

C. If steps A or B show misalignment, proceed to

“Adjusting Riving Knife”.

'%& $(  

1. Raise the Saw Blade  to maximum height and

set the bevel angle to 0°.

2. Remove the Barrier Guard Assembly and Anti-

Kickback Device (see manual).

3. Remove the Table Insert.

4. Place the Rip Fence  on the right side and slide

it until it touches the tips of the Saw Blade  -

Lock fence.

5. Loosen Hex Nut  with 10mm open end wrench

(Fig. 27). Slightly loosen Clamping Screws  (1/4-

1/2 turns) using a 5mm Allen wrench provided

with table saw (stored in the rear of saw). Loosen

Set Screw  using a flat screwdriver (Fig. 27).

6. Make four folds in a small piece of paper (6” x 6”)

forming five layers (Fig. 26). Paper  is used as a

“Spacing Gauge.”

FIG. 25

1

2

!

WARNING

5

FIG. 26

5

4

2

1

5

WORK

LOOKING DOWN

ON SAW

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 20

La page charge ...

Bosch Power Tools GTS1031 GTA500 Manuel utilisateur

Ce manuel convient également à

Bosch Power Tools GTS1031 GTA500 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents