JVC RX-7030VBK Instructions For Use Manual

For Customer Use:

Enter below the Model No. and Serial

No. which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

LVT1007-002A[C]

RX-8030VBK

RX-7030VBK

231

564

89

7/P

0

+10

MENU

ENTER

CONTROL

A/V CONTROL RECEIVER

10/0

(For RX-8030VBK)

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

AUDIO/VIDEO CONTROL RECEIVER

AMPLI/TUNER DE COMMANDE AUDIO/VIDEO

English

Français

COVER_8030&7030[C]7.pm6 03.2.13, 2:53 PM1

G-1

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le

coffret de l’appareil.

2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

Warnings, Cautions and Others/

Mises en garde, précautions et indications diverses

Caution –– STANDBY/ON button!

Disconnect the mains plug to shut the power off completely. The

STANDBY/ON button in any position does not disconnect

the mains line. The power can be remote controlled.

Attention –– Commutateur STANDBY/ON!

Déconnecter la fiche de secteur pour couper complètement le

courant. Le commutateur STANDBY/ON ne coupe jamais

complètement la ligne de secteur, quelle que soit sa position. Le

courant peut être télécommandé.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol,

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

CAUTION

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Section 820-40 of the NEC which provides guidelines

for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

Safety_8030&7030[C]7.pm6 03.2.13, 2:51 PM1

G-2

For Canada/pour Le Canada

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS

B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL

APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING

EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”

ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.

CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE

BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS

NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME

SUR LE MATERIEL BROUILLEUR; “APPAREILS

NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES

COMMUNICATIONS.

For Canada/pour le Canada

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQUAU FOND

For U.S.A

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the

manufacturer for compliance could void the user s authority to

opratethe equipment.

Safety_8030&7030[C]7.pm6 03.2.13, 2:51 PM2

G-3

Caution: Proper Ventilation

To avoid risk of electric shock and fire and to protect from dam-

age.

Locate the apparatus as follows:

Front: No obstructions open spacing.

Sides: No obstructions in 10 cm from the sides.

Top: No obstructions in 10 cm from the top.

Back: No obstructions in 15 cm from the back

Bottom: No obstructions, place on the level surface.

In addition, maintain the best possible air circulation as illus-

trated.

Attention: Ventilation Correcte

Pour éviter les chocs électriques, l’incendie et tout autre dégât.

Disposer l’appareil en tenant compte des impératifs suivants

Avant: Rien ne doit gêner le dégagement

Flancs: Laisser 10 cm de dégagement latéral

Dessus: Laisser 10 cm de dégagement supérieur

Arrière: Laisser 15 cm de dégagement arrière

Dessous: Rien ne doit obstruer par dessous; poser l’appareil

sur une surface plate.

Veiller également à ce que l’air circule le mieux possible comme

illustré.

Spacing 15 cm or more

Dégagement de 15 cm ou plus

RX-8030VBK/RX-7030VBK

Wall or obstructions

Mur, ou obstruction

Front

Avant

Stand height 15 cm or more

Hauteur du socle: 15 cm ou plus

Floor

Plancher

Safety_8030&7030[C]7.pm6 03.2.13, 2:51 PM3

1

English

Table of Contents

Basic Settings ........................................... 25

Setting the Speakers Configuration .......................................... 25

Basic Setting Items ................................................................... 26

Basic Procedure ........................................................................ 27

Setting the Speakers ........................................................... 27

Setting the Speaker Distance ............................................. 28

Setting the Bass Sounds ..................................................... 28

Selecting main or sub channel—DUAL MONO ............... 29

Setting the Digital Input Terminals .................................... 29

Setting the Component Video Input ................................... 30

Memorizing the Volume Level for Each Source ................ 30

Adjusting Sound ........................................ 31

Basic Setting Items ................................................................... 31

Basic Procedure ........................................................................ 31

Adjusting the Equalization Patterns ................................... 32

Adjusting the Speaker Output Levels ................................ 32

Adjusting the Sound Parameters for the

Surround and DSP modes ............................................ 33

Using the Surround Modes ..........................

34

Reproducing Theater Ambience ................................................ 34

Introducing the Surround Modes ............................................. 34

Surround Modes Applicable to the Various Software .............. 36

Activating the Surround Modes ............................................... 37

7 Activating the EX/ES setting ................................................ 37

7 Activating the Surroung modes ............................................ 37

Using the DSP Modes ................................ 38

Reproducing the Sound Field ................................................... 38

Introducing the DSP Modes ..................................................... 38

Activating the DSP Modes ....................................................... 39

Using the DVD MULTI Playback Mode .......... 40

Activating the DVD MULTI Playback Mode .......................... 40

COMPU LINK Remote Control System ......... 41

AV COMPU LINK Remote Control System .... 42

Operating JVC’s Audio/Video Components ... 44

Operating Audio Components .................................................. 44

Operating Video Components .................................................. 46

Operating Other Manufacturers’ Video

Equipment ............................................ 47

Troubleshooting ......................................... 50

Specifications............................................ 51

Introduction ................................................ 2

Features ...................................................................................... 2

Precautions ................................................................................. 2

Parts Identification ...................................... 3

Remote Control .......................................................................... 3

Front Panel ................................................................................. 4

Rear Panel .................................................................................. 6

Getting Started ........................................... 8

Before Installation ...................................................................... 8

Checking the Supplied Accessories ........................................... 8

Putting Batteries in the Remote Control .................................... 8

Connecting the FM and AM Antennas ....................................... 8

Connecting the Speakers ............................................................ 9

Connecting Audio/Video Components ..................................... 11

7 Analog Connections ............................................................. 11

7 Digital Connections .............................................................. 16

Connecting the Power Cord ..................................................... 16

Basic Operations ....................................... 17

Daily Operational Procedure .................................................... 17

Turning On the Power .............................................................. 17

Selecting the Source to Play ..................................................... 17

Adjusting the Volume ............................................................... 18

Selecting the Front Speakers .................................................... 19

Activating and Adjusting the Subwoofer Sound ...................... 19

Selecting the Analog or Digital Input Mode ............................ 19

Setting the Dynamic Range ...................................................... 20

Attenuating the Input Signal .................................................... 20

Turning Analog Direct On and Off .......................................... 21

Making Sounds Natural............................................................ 21

Changing the Source Name ...................................................... 21

Reinforcing the Bass ................................................................ 22

Muting the Sound ..................................................................... 22

Changing the Display Brightness ............................................. 22

Using the Sleep Timer .............................................................. 22

Receiving Radio Broadcasts ........................ 23

Tuning in to Stations Manually ................................................ 23

Using Preset Tuning ................................................................. 23

Selecting the FM Reception Mode ........................................... 24

This mark indicates that ONLY the remote control

CAN be used for the operation explained.

This mark indicates that the remote control

CANNOT be used for the operation explained.

Use the buttons on the front panel.

Features with this mark are provided only for

RX-8030VBK.

Features with this mark are provided only for

RX-7030VBK.

RX-8030V

ONLY

RX-7030V

ONLY

Remote

NOT

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM1

2

English

Introduction

We would like to thank you for purchasing one of our JVC products.

Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance

from your unit, and retain this manual for future reference.

Features

CC (Compensative Compression) converter

—ONLY for RX-8030VBK

CC Converter eliminates jitter and ripples, achieving a drastic

reduction in digital distortion by processing the digital music data

in 24 bit–quantization and by expanding the sampling frequency

to 128 kHz (for fs 32 kHz signals)/176.4 kHz (for fs 44.1 kHz

signals)/192 kHz (for fs 48 kHz signals). By using the CC

Converter, you can obtain a natural sound field from any source.

(See page 21 for details.)

K2 technology—ONLY for RX-8030VBK

K2 technology has been designed to enable natural audio

reproduction, achieving a drastic reduction in digital distortion

and creating original sound ambience with high precision.

Compatible with various audio formats including

DTS 96/24

RX-8030VBK and RX-7030VBK allow you to enjoy a newly

introduced audio format such as Dolby Digital EX, Dolby Pro

Logic II, DTS-ES, DTS Neo:6, and DTS 96/24.

• This unit is also compatible with Dual Mono signals recorded in

Dolby Digital and DTS discs.

DAP (Digital Acoustic Processor)

Sound field simulation technology allows precise ambience

recreation of existing theaters and halls. Thanks to the high-

performance DSP (Digital Signal Processor) and high-capacity

memory, you can enjoy multi-channel surround sound by playing

2-channel or multi-channel software according to the speaker

setting.

Multi-channel headphone virtual surround

sound—3D HEADPHONE Mode

The built-in headphone virtual surround system is compatible with

Multi-channel software like Dolby Digital, DTS Surround, etc.

Thanks to the new signal processing algorithms used by the high-

performance DSP, you can enjoy a natural surround sound through

the headphones.

COMPU LINK/AV COMPU LINK remote control

systems

These COMPU LINK remote control systems allow you to

operate other JVC’s audio/video components from this receiver.

Precautions

Power sources

• When unplugging the receiver from the wall outlet, always pull

the plug, not the AC power cord.

• Do not handle the AC power cord with wet hands.

• If you are not going to operate the receiver for an extended period

of time, unplug the AC power cord from the wall outlet.

Ventilation

High power amplifiers built in this receiver will generate heat inside

the cabinet. For safety, observe the following carefully.

• Make sure there is good ventilation around the receiver. Poor

ventilation could overheat and damage the receiver.

• Do not block the ventilation openings or holes. (If the ventilation

openings or holes are blocked by a newspaper or cloth, etc., the

heat may not be able to get out.)

Others

• Should any metallic object or liquid fall onto the unit, unplug the

unit and consult your dealer before operating any further.

• Do not expose this apparatus to rain, moisture, dripping or

splashing and that no objects filled with liquids, such as vases

shall be placed on the apparatus.

• Do not disassemble the unit since there are no user serviceable

parts inside.

If anything goes wrong, unplug the AC power cord and consult your

JVC dealer.

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM2

3

English

Parts Identification

1 Only for RX-8030VBK: Display window

• When the remote operation mode changes, it is shown on

this display.

• Signal transmission indicator (A) lights up when

transmitting signals.

2

buttons (17, 46 – 48)

• For RX-8030VBK:

CATV/DBS , VCR 1 , TV , AUDIO

• For RX-7030VBK:

CATV/DBS , VCR , TV , AUDIO

3 Source selection buttons (17, 18, 19, 23, 24, 37, 40)

• For RX-8030VBK:

DVD MULTI, DVD, CD*, FM/AM*, VCR 1, VCR 2,

CDR*, TAPE/MD*, TV/DBS, VIDEO, PHONO*

• For RX-7030VBK:

DVD MULTI, DVD, CD*, FM/AM*, TV/DBS, VCR,

TAPE/CDR*

* When you press one on these source selection buttons on the

remote control, the receiver automatically turns on.

4 • SURROUND button (37)

• DSP button (39)

• SURR (surround)/DSP OFF button (37, 39)

• EX/ES button (37)

5 • For RX-8030VBK: CC CONVERTER button (21)

• For RX-7030VBK: CD DISC button (45)

6 MIDNIGHT MODE button (20)

7 SOUND button (22, 32, 33)

8 CATV/DBS CONTROL button (47)

9 TV/VIDEO button (46, 47)

p • For RX-8030VBK: CONTROL button (44 – 46)

• For RX-7030VBK: VCR CONTROL button (46)

q REC PAUSE button (45, 46, 48)

w SLEEP button (22)

e ANALOG/DIGITAL INPUT button (20)

r ANALOG DIRECT button (21)

t • 10 keys for operating the tuner (24)

• 10 keys for adjusting sound (32, 33)

• 10 keys for operating audio/video components (44 – 48)

y • CH (channel) +/– buttons (46 – 48)

• *LEVEL +/– buttons (32, 33, 44)

The LEVEL +/– buttons function only after pressing SOUND

then 10 keys which are marked with an asterisk (*) on the

remote control.

u VOLUME +/– buttons (18)

i TV VOL (volume) +/– buttons (46, 47)

o MUTING button (22)

; • TUNING UP/DOWN buttons (23)

• Operating buttons for audio/video components (44 – 46, 48)

3, 8, 7, 4/REW, FF/¢

a DIMMER button (22)

å Only for RX-7030VBK: TAPE/CDR CONTROL button (45)

Remote Control

RX-8030VBK RX-7030VBK

+

−

+

−

+

−

231

564

89

7/P

0

+10

MENU

ENTER

BASS BOOST

TEST

∗

CENTER

∗

SUB WOOFER

∗

DIGITAL EQ

∗

SURR BACK

CH/

∗

LEVEL

TV VOL

/REW

DOWN — TUNING — UP

FF/

MUTING

DIMMER

VOLUME

CATV/DBS

CONTROL

TV/VIDEO

REC PAUSE

SLEEP

RETURN FM MODE 100

+

CONTROL

REMOTE CONTROL

RM-SRX8030J

CATV/DBS VCR 1 TV AUDIO

DSP

OFF

DVD MULTI

CD

CDR

TAPE/MD

TV/DBS VIDEO PHONO

FM/AM

VCR 1 VCR 2

SURROUND

EX/ES

CC CONVERTER

SURR/DSP

ANALOG/DIGITAL

A/V CONTROL RECEIVER

INPUT

MIDNIGHT

MODE

DIRECT

ANALOG

DVD

u

i

1

3

4

9

p

q

w

t

;

a

10/0

y

2

SOUND

8

6

5

7

o

r

e

A

+

−

+

−

+

−

231

564

89

7/P

0

+10

MENU

ENTER

TESTCD DISC

∗

CENTER

∗

SUB WOOFER

∗

DIGITAL EQ

∗

SURR BACK

CH/

∗

LEVEL

TV VOL

/REW

DOWN — TUNING — UP

FF/

MUTING

DIMMER

VOLUME

CATV/DBS

CONTROL

VCR

CONTROL

TAPE/CDR

CONTROL

TV/VIDEO

REC PAUSE

SLEEP

RETURN FM MODE 100

+

REMOTE CONTROL

RM-SRX7030J

CATV/DBS VCR TV AUDIO

DSP

OFF

DVD MULTI

CD

TAPE/CDR

ANALOG/DIGITAL

FM/AM

TV/DBS VCR

SURROUND

EX/ES

SURR/DSP

A/V CONTROL RECEIVER

INPUT

MIDNIGHT

MODE

DIRECT

ANALOG

DVD

u

i

3

4

9

p

q

w

t

;

a

10/0

y

2

SOUND

8

6

5

7

o

r

e

s

BASS BOOST

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM3

4

English

Display Window

Front Panel

Press down on PUSH OPEN.

How to open the front door

SUBWOOFER OUT ON/OFF

SPEAKERS ON/OFF

PHONES

1

STANDBY

ANALOG DIRECT

2

STANDBY/ON

TUNER CONTROL

SETTING ADJUST

QUICK SPEAKER

SETUP

EXIT

MIDNIGHT

MODEEX / ES

INPUT ATT

INPUT

ANALOG

INPUT

DIGITAL

FM/AM TUNING FM/AM PRESET FM MODE MEMORY

SURROUND

DSP

SURROUND/ DSP

OFF

VIDEO

L—AUDIO—RDIGITAL S-VIDEO VIDEO

PUSH SET

MULTI JOG

MASTER VOLUME

1

2

;

s

i

a

4 5 7

u o

p

9

3

PUSH OPEN

CC CONVERTER

BASS BOOST

8

RX-8030VBK

RX-7030VBK

Only for RX-8030VBK

Inside the front door

TUNER CONTROL

MIDNIGHT

MODEEX / ES

INPUT ATT

INPUT

ANALOG

INPUT

DIGITAL

FM/AM TUNING FM/AM PRESET FM MODE MEMORY

VIDEO

L—AUDIO—RDIGITAL S-VIDEO VIDEO

r

eq

w

y

t

6

TV SOUND

/DBS

VIDEOVCR 2VCR 1

DVDDVD MULTI AMFMTAPE/MDCDRCDPHONO

TV SOUND/DBSVCR

DVDDVD MULTI AMFMTAPE/CDRCD

RX-8030VBK

RX-7030VBK

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM4

5

English

Front Panel

1 STANDBY/ON button and STANDBY lamp (17)

2 • SPEAKERS ON/OFF 1 button (19)

• SPEAKERS ON/OFF 2 button (19)

3 • SURROUND button (37)

• DSP button (39)

• SURROUND/DSP OFF button (37, 39)

4 Remote sensor

5 Display window (17)

6 • For RX-8030VBK: Source selection buttons and lamps

(17, 18, 19, 21, 23, 24, 37, 40)

DVD MULTI, DVD, VCR 1, VCR 2, VIDEO,

TV SOUND/DBS, PHONO, CD, CDR, TAPE/MD, FM, AM

(The lamp above the button for selected source lights up.)

• For RX-7030VBK: Source selection buttons

(17, 18, 19, 21, 23, 24, 37, 40)

DVD MULTI, DVD, VCR , TV SOUND/DBS, CD,

TAPE/CDR, FM, AM

7 MASTER VOLUME control (18)

8 • For RX-8030VBK: CC CONVERTER button and lamp (21)

• For RX-7030VBK: BASS BOOST button and lamp (22)

9 SUBWOOFER OUT ON/OFF button (19)

p PHONES jack (19)

q EX/ES button (37)

Display Window

1 DUAL indicator (35)

2 ANALOG indicator (20)

3 DIGITAL AUTO indicator (20)

4 96/24 indicator (35)

5 MULTI indicator (40)

6 •

PRO LOGIC indicator (34)

• PRO LOGIC II indicator (35)

7 TUNED indicator (23)

8 STEREO indicator (23, 24)

9 NEO:6 indicator (35)

0 AUTO MUTING indicator (24)

- VIRTUAL SB (Surround Back) indicator (34, 35)

= ONE TOUCH OPERATION indicator (30)

w • INPUT ANALOG button (20)

• INPUT ATT button (20)

e MIDNIGHT MODE button (20)

r INPUT DIGITAL button (20)

t TUNER CONTROL buttons

• FM/AM TUNING 5 / ∞ buttons (23)

• FM/AM PRESET 5 / ∞ buttons (23, 24)

• FM MODE button (24)

• MEMORY button (23)

y Only for RX-8030VBK: VIDEO input jacks (13)

DIGITAL optical terminal, S-VIDEO jack, VIDEO jack,

AUDIO—L/R jacks

u SETTING button (27)

i QUICK SPEAKER SETUP button (25)

o • MULTI JOG control (25, 27, 31)

• PUSH SET button (25, 27, 31)

; EXIT button (27, 31)

a ADJUST button (31)

s ANALOG DIRECT button and lamp (21)

~ SLEEP indicator (22)

! MIDNIGHT MODE indicator (20)

@ DIGITAL EQ (equalization) indicator (32)

# Speaker and signal indicators (18)

$ Digital signal format indicators (20)

% Main Display (17)

^ DSP indicator (19, 38)

& 3D-PHONIC indicator (38)

* HEADPHONE indicator (19, 38)

( SPEAKERS 1/2 indicators (19)

) INPUT ATT (attenuator) indicator (20)

_ VOLUME level indicator (17, 22)

+ BASS BOOST indicator (22)

Display Window

DIGITAL EQ

INPUT ATT

SLEEP

VOLUME

ONE TOUCH OPERATION

3D - PHONIC

NEO:6

VIRTUAL SB

MIDNIGHT MODE

AUTO MUTING

TUNED STEREO

LINEAR PCM

DIGITAL

L

SUBWFR

LS RS

CR

S

LFE

DUAL DIGITAL

AUTO

ANALOG 96/24 MULTI

PRO LOGIC

DSP

HEADPHONE SPEAKERS 1 2

BASS BOOST

SB

# $ %

_

1 2

3

4

5

6

7 8 0

9

-

= ~

+

^ & *

@

!

(

)

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM5

6

English

Rear Panel

RX-8030VBK

RX-7030VBK

VIDEO

RIGHT LEFT

L

R

L

R

S-VIDEO

VIDEO

SURR BACK

SURR CENTER

FRONT

AUDIO

DIGITAL IN

DIGITAL 1 (DVD)

DIGITAL 2 (CD)

DIGITAL 3 (TV)

DIGITAL 4 (CDR)

PCM/ DOLBY DIGITAL

/ DTS

DIGITAL OUT

FM 75

COAXIAL

AM

EXT

AM

LOOP

RIGHT

LEFT

+

–

+

–

12

CENTER

SPEAKER

SURROUND SPEAKERS

816

CAUTION : SPEAKER IMPEDANCE

MONITOR

OUT

SUBWOOFER CENTER

DVD

IN

OUT

(REC)

TAPE

MD

IN

(PLAY)

OUT

(REC)

CDR

IN

(PLAY)

PHONO

IN

FRONT

TV SOUND

DBS

IN

VCR 2

VCR 1

IN

(PLAY)

IN

(PLAY)

OUT

(REC)

OUT

(REC)

CD

IN

RIGHT LEFT

DVD

IN

ANTENNA

SUBWOOFER

COMPONENT VIDEO

MONITOR

OUT

DBS

IN

DVD

IN

Y

PB

PR

COMPU LINK-4

(SYNCHRO)

AV

COMPULINK-

SURROUND BACK SPEAKERS

FRONT SPEAKERS

RIGHT

LEFT

RIGHT

LEFT

RIGHT

LEFT

CAUTION : SPEAKER IMPEDANCE

SINGLE USE

See Instruction

Manual For

Connection

1

OR

2 :

8

16

1

AND

2 :

16

32

PREOUT

SURR

(REAR)

12

3456789

trewq

p

y

VIDEO

RIGHT LEFT

S-VIDEO

VIDEO

AUDIO

DIGITAL IN

DIGITAL 1 (DVD)

DIGITAL 2 (CD)

DIGITAL 3 (TV)

DIGITAL 4 (CDR)

PCM/ DOLBY DIGITAL

/ DTS

DIGITAL OUT

FM 75

COAXIAL

AM

EXT

AM

LOOP

RIGHT

LEFT

+

–

+

–

12

CENTER

SPEAKER

SURROUND SPEAKERS

816

CAUTION : SPEAKER IMPEDANCE

MONITOR

OUT

SUBWOOFER CENTER

DVD

IN

SURR

(REAR)

TAPE

CDR

FRONT

TV SOUND

DBS

IN

VCR

IN

(PLAY)

IN

(PLAY)

OUT

(REC)

OUT

(REC)

CD

IN

RIGHT LEFT

DVD

IN

ANTENNA

COMPONENT VIDEO

MONITOR

OUT

DBS

IN

DVD

IN

Y

P

B

P

R

COMPU LINK-4

(SYNCHRO)

AV

COMPULINK-

SURROUND BACK SPEAKERS

RIGHT

LEFT

RIGHT

LEFT

RIGHT

LEFT

CAUTION : SPEAKER IMPEDANCE

SINGLE USE

See Instruction

Manual For

Connection

1

OR

2 :

8

16

1

AND

2 :

16

32

SUBWOOFER

OUT

+ +

– –

123456789

reqp w

FRONT SPEAKERS

t

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM6

7

English

Rear Panel

RX-8030VBK

1 DIGITAL IN terminals (16)

• Coaxial: DIGITAL 1 (DVD)

• Optical: DIGITAL 2 (CD), DIGITAL 3 (TV),

DIGITAL 4 (CDR)

2 AUDIO input/output jacks (11 – 15)

• Input: DVD IN—FRONT, CENTER, SUBWOOFER,

SURR (REAR), TV SOUND/DBS IN,

VCR 1 IN (PLAY), VCR 2 IN (PLAY), CD IN,

TAPE/MD IN (PLAY), CDR IN (PLAY),

PHONO IN

• Output: VCR 1 OUT (REC), VCR 2 OUT (REC),

TAPE/MD OUT (REC), CDR OUT (REC)

3 S-VIDEO and composite VIDEO input/output jacks (14, 15)

• Input: DVD IN, TV SOUND/DBS IN, VCR1 IN (PLAY),

VCR 2 IN (PLAY)

• Output: VCR 1 OUT (REC), VCR 2 OUT (REC),

MONITOR OUT

4 FM/AM ANTENNA terminals (8)

5 PREOUT jacks (10, 11)

• FRONT, CENTER, SUBWOOFER, SURR, SURR BACK

6 COMPONENT VIDEO input/output jacks (14, 15)

• Input: DVD IN, DBS IN

• Output: MONITOR OUT

7 COMPU LINK-4 (SYNCHRO) terminals (41)

8 AV COMPULINK-III terminals (42)

9 AC power cord (16)

p DIGITAL OUT terminal (16)

q SURROUND BACK SPEAKERS terminal (10)

w SURROUND SPEAKERS terminal (10)

e CENTER SPEAKER terminal (10)

r FRONT SPEAKERS 1 terminals (10)

t FRONT SPEAKERS 2 terminals (10)

Ô Earth (ground) terminal (11)

RX-7030VBK

1 DIGITAL IN terminals (16)

• Coaxial: DIGITAL 1 (DVD)

• Optical: DIGITAL 2 (CD), DIGITAL 3 (TV),

DIGITAL 4 (CDR)

2 AUDIO input/output jacks (12 – 15)

• Input: DVD IN—FRONT, CENTER, SUBWOOFER,

SURR (REAR), TV SOUND/DBS IN,

VCR IN (PLAY), TAPE/CDR IN (PLAY), CD IN

• Output: VCR OUT (REC), TAPE/CDR OUT (REC)

3 S-VIDEO and composite VIDEO input/output jacks (14, 15)

• Input: DVD IN, TV SOUND/DBS IN, VCR IN (PLAY)

• Output: VCR OUT (REC), MONITOR OUT

4 FM/AM ANTENNA terminals (8)

5 SUBWOOFER OUT jack (10)

6 COMPONENT VIDEO input/output jacks (14, 15)

• Input: DVD IN, DBS IN

• Output: MONITOR OUT

7 COMPU LINK-4 (SYNCHRO) terminals (41)

8 AV COMPULINK-III terminals (42)

9 AC power cord (16)

p DIGITAL OUT terminal (16)

q SURROUND BACK SPEAKERS terminal (10)

w SURROUND SPEAKERS terminal (10)

e CENTER SPEAKER terminal (10)

r FRONT SPEAKERS 1 terminals (10)

t FRONT SPEAKERS 2 terminals (10)

RX-8030VBK

RX-7030VBK

PREOUT jacks

嘷

⳯

Video jacks (input/output)

Composite video (4/3)

S-video (4/3)

Component video (2/1)

Composite video (3/2)

S-video (3/2)

Component video (2/1)

CC Converter

嘷

⳯

Selectable source

DVD MULTI, DVD, VCR 1, VCR 2, VIDEO,

TV SOUND/DBS, PHONO, CD, CDR, TAPE/MD,

FM, AM

DVD MULTI, DVD, VCR,

TV SOUND/DBS, CD, TAPE/CDR, FM, AM

嘷: Supplied ⳯: Not supplied

Differences between RX-8030VBK and RX-7030VBK

Remote Control

RM-SRX8030J

RM-SRX7030J

Color

Black

Display Window

嘷

⳯

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM7

8

English

FM 75

COAXIAL

AM

EXT

AM

LOOP

ANTENNA

FM 75

COAXIAL

ANTENNA

FM 75

COAXIAL

ANTENNA

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the

power supply.

Before Installation

General Precautions

• Be sure your hands are dry.

• Turn the power off to all components.

• Read the manuals supplied with the components you are going to

connect.

Locations

• Install the receiver in a location that is level and protected from

moisture.

• The temperature around the receiver must be between –5˚C and

35˚C (23˚F and 95˚F ).

• Make sure there is good ventilation around the receiver. Poor

ventilation could cause overheating and damage the receiver.

Handling the receiver

• Do not insert any metal object into the receiver.

• Do not disassemble the receiver or remove screws, covers, or

cabinet.

• Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are

supplied with the receiver.

The number in the parentheses indicates quantity of the pieces

supplied.

• Remote Control (1)

• Batteries (2)

• AM Loop Antenna (1)

• FM Antenna (1)

If anything is missing, contact your dealer immediately.

Putting Batteries in the Remote Control

Before using the remote control, insert the two supplied batteries

first.

1. Press and slide the battery cover on the back of

the remote control.

2. Insert the batteries.

• Make sure to match the polarity: (+) to (+) and (–) to (–).

3. Replace the cover.

B

FM Antenna (supplied)

Outdoor FM Antenna Cable

(not supplied)

Extend the supplied FM antenna

horizontally.

A

If the remote control cannot transmit signals or operate the receiver

correctly, replace the batteries. Use two R6P(SUM-3)/AA(15F) type

dry-cell batteries.

Notes:

• Supplied batteries are for the initial setup. Replace for continued

use.

• After replacing the batteries, set the manufacturers’ codes again

(see pages from 47 to 49).

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

• Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

• Use the correct type of batteries. Batteries that look similar may

differ in voltage.

• Always replace both batteries at the same time.

• Do not expose batteries to heat or flame.

Connecting the FM and AM Antennas

FM Antenna Connections

A. Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75 Ω

COAXIAL terminal as temporary measure.

B. Using the Standard Type Connector (Not Supplied)

A standard type connector should be connected to the FM 75 Ω

COAXIAL terminal.

Note:

If reception is poor, connect the outdoor FM antenna (not supplied).

Before attaching a 75

Ω

coaxial cable with a connector (the kind with

a round wire going to an outdoor antenna), disconnect the supplied

FM antenna.

1

2

R6P(SUM-3)/

AA(15F)

3

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM8

9

English

RIGHT

LEFT

RIGHT

LEFT

RIGHT

LEFT

+

–

RIGHT

LEFT

AM Antenna Connections

Turn the loop until you have the

best reception.

AM Loop Antenna

(supplied)

Snap the tabs on the loop into the slots

of the base to assemble the AM loop.

Outdoor single vinyl-covered wire (not supplied)

Notes:

• If the AM loop antenna wire is covered with vinyl, remove

the vinyl by twisting it as illustrated.

• Make sure the antenna conductors do not touch any

other terminals, connecting cords and power cord. This

could cause poor reception.

• If reception is poor, connect an outdoor single vinyl-covered wire

(not supplied) to the AM EXT terminal. (Keep the AM loop antenna

connected.)

Connecting the Speakers

You can connect the following speakers:

• Two pairs of front speakers to produce normal stereo sound.

• One pair of surround speakers to enjoy the surround effect.

• One surround back speaker or one pair of surround back speakers

to enjoy to produce more effective surround effect.

• One center speaker to emphasize human voices.

• One subwoofer to enhance the bass.

CAUTION:

Use only the speakers of the SPEAKER IMPEDANCE indicated by

the speaker terminals.

• When connecting to both of the FRONT SPEAKERS 1 and 2

terminals, use speakers with an impedance of 16 Ω to 32 Ω.

• When connecting to either the FRONT SPEAKERS 1 or 2

terminals, use speakers with an impedance of 8 Ω to 16 Ω.

Basic connecting procedure

1 Twist and remove the insulation at

the end of each speaker signal cable

(not supplied).

2 Open the speaker terminal.

RX-7030VBK

(For FRONT SPEAKERS 2 terminals)

3 Insert the speaker signal cable.

4 Close the speaker terminal.

For each speaker (except for a subwoofer), connect the (+) and

(–) terminals on the rear panel to the (+) and (–) terminals

marked on the speakers.

Subwoofer

Speaker layout

Ideal speaker layout varies depending on the conditions of your

listening room. The diagram below is a recommended typical

example.

Left front speaker(s)

(L)

Right front speaker(s)

(R)

Center speaker

(C)

Surround back speakers (LSB/RSB)

Left surround

speaker (LS)

Right surround

speaker (RS)

+

–

RIGHT

LEFT

FM 75

COAXIAL

AM

EXT

AM

LOOP

ANTENNA

2

3

1

+

–

RIGHT

LEFT

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM9

10

English

Placing speakers

Front speakers and center speaker

• Place these speakers (position of the mid-range speaker units) at the same

height from the floor.

• Point these speakers aiming at the listener’s ears.

Surround and surround back speakers

• Place these speakers at a position which is 1 meter higher than the listener’s

ears.

• Point these speakers down aiming at the listener’s ears.

Subwoofer

• You can place it wherever you like since bass sound is non-directional.

Normally place it in front of you.

Note:

Ideal speaker layout requires that all speakers be placed at the same distance

from the listener. However, since in some places it may be difficult to fulfil this

requirement, this unit can adjust the delay time so that the sounds through all the

speakers reach the listener with the same timing. (See page 28.)

Subwoofer

IMPORTANT:

After connecting the speakers, set the speaker

installation information properly. You can use Quick

Speaker Setup for easy speaker installation information

setting (see page 25).

• To obtain the best possible Surround/DSP effect, see

“Setting the Speakers” on page 27.

Front speakers 1

Right / Left

Surround back speakers*

Right / Left

Front speakers 2

Right / Left

Center speaker

*

When using only one

surround back speaker,

connect the

ª

cord to the

RIGHT

ª

terminal and the

·

cord to the LEFT

·

terminal.

Surround speakers

Right / Left

RIGHT

LEFT

+

–

+

–

CENTER

SPEAKER

SURROUNDSPEAKERS

816

CAUTION : SPEAKER IMPEDANCE

SURROUND BACK SPEAKERS

FRONT SPEAKERS

RIGHT

LEFT

RIGHT

LEFT

RIGHT

LEFT

CAUTION : SPEAKER IMPEDANCE

SINGLE USE

See Instruction

Manual For

Connection

1

OR

2 :

8

16

1

AND

2 :

16

32

1

2

Connecting the subwoofer speaker

You can enhance the bass by connecting a subwoofer.

Connect the input jack of a powered subwoofer to the rear panel, using a cable with RCA

pin plugs (not supplied).

L

R

L

R

SURR BACK

SURR CENTER

FRONT

SUBWOOFER

PREOUT

SUBWOOFER

OUT

RX-7030VBK

RX-8030VBK

RIGHT

LEFT

+

–

SU

8

CAUTION : SPEAKER IMPEDANCE

SURROUND BACK SPEAKERS

SINGLE USE

See Instruction

Manual For

Connection

C

LR

LS RS

LSB

RSB

SB*

* When one surround back speaker is

connected.

• Rear terminals of RX-8030VBK are used for explanation.

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM10

11

English

PHONO

IN

RIGHT LEFT

R

L

RX-8030VBK

L

R

L

R

SURR BACK

SURR CENTER

FRONT

SUBWOOFER

PREOUT

R

L

R

L

Connecting Audio/Video Components

When connecting individual components, refer also to the manuals

supplied with them.

Analog Connections

If your audio components have digital audio output terminal,

connecting them using the digital cords explained in “Digital

Connections” (see page 16) will give you better sound quality.

Audio component connections

Use the cables with RCA pin plugs (not supplied).

• Connect the white plug to the audio left jack, and the red plug to

the audio right jack.

If your audio components have a COMPU LINK jack

See also page 41 for detailed information about the connection

and the COMPU LINK remote control system.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer

between the source components and this receiver, the sound output

through this receiver may be distorted.

Turntable

To listen to the sound after connection, press PHONO.

If a ground cable is

provided for your turntable,

connect the cable to the

screw marked (H) on the

rear.

Note:

This connection is for the turntable with an MM (moving-magnet) type

cartridge.

Any turntables incorporating a small-output cartridge such as an MC

(moving-coil) type must be connected to this receiver through a

commercial head amplifier or step-up transformer. Direct connection

may result in insufficient volume.

Power amplifier

Right front speaker

Power amplifier

Right surround

speaker

Left surround

speaker

Power amplifier

Center speaker

Enhancing your audio system

—Only for RX-8030VBK

You can use this receiver as the pre-amplifier (control amplifier)

when you connect power amplifiers to the PREOUT jacks on the

rear using cables with RCA pin plugs (not supplied).

• Connect the white plug to the audio left jack, and the red plug to

the audio right jack.

Note:

If you connect one surround back speaker, connect the surround back

speaker to the left surround back PREOUT jack (SURR BACK L).

To audio output

Turntable

RX-8030V

ONLY

RX-8030V

ONLY

Surround back speakers

Left / Right

Left front speaker

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM11

12

English

CD player

To listen to the sound after connection, press CD.

Cassette deck

To listen to the sound after connection, press TAPE/MD (for RX-

8030VBK) or TAPE/CDR (for RX-7030VBK).

For RX-8030VBK

You can connect either a cassette deck or an MD recorder to the

TAPE/MD jacks. When connecting an MD recorder, see page 13.

For RX-7030VBK

You can connect either a cassette deck or a CD recorder to the

TAPE/CDR jacks. When connecting an CD recorder to the TAPE/

CDR jacks, see the right column.

CD

IN

R

L

RX-8030VBK/RX-7030VBK

OUT

(REC)

TAPE

MD

IN

(PLAY)

RX-8030VBK

R

L

R

L

CD recorder

To listen to the sound after connection, press CDR (for

RX-8030VBK) or TAPE/CDR (for RX-7030VBK).

For RX-8030VBK

For RX-7030VBK

You can connect either a CD recorder or a cassette deck to the

TAPE/CDR jacks. When connecting a cassette deck to the TAPE/

CDR jacks, see the left column.

Note:

For RX-7030VBK: When connecting a CD recorder to the TAPE/CDR

jacks, change the source name to “CDR,” which will be shown on the

display when it is selected as the source. See page 21 for details.

To audio output

To audio input

Cassette deck

To audio output

To audio input

Cassette deck

RX-7030VBK

TAPE

CDR

IN

(PLAY)

OUT

(REC)

R

L

R

L

RX-8030VBK

OUT

(REC)

CDR

IN

(PLAY)

R

L

R

L

To audio output

To audio input

CD recorder

To audio output

To audio input

CD recorder

To audio

output

CD player

TAPE

CDR

IN

(PLAY)

OUT

(REC)

RX-7030VBK

R

L

R

L

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM12

13

English

MD recorder

To listen to the sound after connection, press TAPE/MD (for RX-

8030VBK) or TAPE/CDR (for RX-7030VBK).

For RX-8030VBK

You can connect either an MD recorder or a cassette deck to the

TAPE/MD jacks. When connecting a cassette deck, see page 12.

Note:

When connecting an MD recorder to the TAPE/MD jacks, change the

source name to “MD,” which will be shown on the display when it is

selected as the source. See page 21 for details.

For RX-7030VBK

You can connect an MD recorder to the TAPE/CDR jacks if they are

not used for connecting another component such as a cassette deck

or CD recorder. When connecting an MD recorder to the TAPE/

CDR jacks, see page 12.

• Though your MD recorder is one of JVC products with the

COMPU LINK remote control system, you cannot use the

COMPU LINK remote control system to operate the connected

MD recorder.

OUT

(REC)

TAPE

MD

IN

(PLAY)

RX-8030VBK

R

L

R

L

To audio output

To audio input

MD recorder

Video component connections

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, the red plug to the

audio right jack, and the yellow plug to the video jack.

• If your video components have S-video (Y/C-separation) and/or

component video (Y, P

B, PR) terminals, connect them using an S-

video cable (not supplied) and/or component video cable (not

supplied). By using these jacks, you can get better picture quality

in the order—Component video > S-video > Composite video.

If your video components have an AV COMPULINK jack

See also page 42 for detailed information about the connection

and the AV COMPU LINK remote control system.

IMPORTANT:

This receiver is equipped with the following video jacks—composite

video, S-video and component video jacks. You can use any of the

three to connect a video component.

However, the video signals from one type of these input jacks are

transmitted only through the video output jacks of the same

type.

Therefore, if a recording video component and a playing video

component are connected to the receiver through the video jacks of

different type, you cannot record the picture. In addition, if the TV and

a playing video component are connected to the receiver through the

video jacks of different type, you cannot view the playback picture on

the TV.

Video camera

To listen to the sound after connection, press VIDEO.

The VIDEO input jacks on the front panel (inside the front door) are

convenient when connecting and disconnecting the component

frequently.

S-VIDEODIGITAL

VIDEO L—AUDIO—R

VIDEO

R

L

To composite video

output

To S-video output

To optical digital output

To audio output

Video camera

When using the digital input terminal

Select the digital input mode correctly.

For details, see “Selecting the Analog or Digital Input Mode” on

page 19.

RX-8030V

ONLY

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM13

14

English

VCR(s)

To listen to the sound after connection, press VCR 1 or VCR 2 (for

RX-8030VBK) or VCR (for RX-7030VBK).

For RX-8030VBK

You can connect two VCRs—one to the VCR 1 jacks and the other

to the VCR 2 jacks.

• If your VCR has an AV COMPU LINK jack, connect it to the

VCR 1 jack so that you can use the AV COMPU LINK remote

control system.

Å To audio input

ı To audio output

Ç To S-video output

Î To composite video output

‰ To S-video input

Ï To composite video input

For RX-7030VBK

Å To audio input

ı To audio output

Ç To S-video output

Î To composite video output

‰ To S-video input

Ï To composite video input

RX-8030VBK

VCR 2

VCR 1

IN

(PLAY)

IN

(PLAY)

OUT

(REC)

OUT

(REC)

A B

DC E F

R

L

R

L

RX-7030VBK

VCR

IN

(PLAY)

OUT

(REC)

A B

DC E F

R

L

R

L

TV and/or DBS tuner

To listen to the sound after connection, press TV SOUND/DBS (or

TV/DBS on the remote control).

TV

DBS tuner

Å To audio output

ı To component video input

Ç To S-video input

Î To composite video input

When connecting

the TV to the

AUDIO jacks (TV

SOUND/DBS IN),

DO NOT connect

the TV’s video

output to these

video input jacks.

Å To audio output

ı To component video output

Ç To S-video output

Î To composite video output

Notes:

• When connecting a DBS tuner to the TV SOUND/DBS IN jacks,

change the source name to “DBS,” which will be shown on the

display when selected as the source. Otherwise you cannot view

any picture from DBS tuner. See page 21 for details.

• When connecting a DBS tuner to either one of the component input

jacks, make the component video input setting correctly for AV

CONPU LINK. See page 30 for details.

MONITOR

OUT

TV SOUND

DBS

IN

MONITOR

OUT

Y

P

B

P

R

A

B

C

D

R

L

RX-8030VBK/RX-7030VBK

Connect the TV to appropriate MONITOR OUT jacks to view

the playback picture from any other connected video

components.

TV SOUND

DBS

IN

DBS

IN

A

B

C

D

R

L

DBS

RX-8030VBK/RX-7030VBK

VCR

TV

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM14

15

English

DVD player

• When you connect a DVD player with stereo output jacks:

To listen to the sound after connection, press DVD.

Å To component video output

ı To S-video output

Ç To composite video output

Î To left/right front channel audio output (or to audio-

mixed output if necessary)

Note:

When connecting a DVD player to the component video input jacks,

make the component video input setting correctly for AV COMPU

LINK. See page 30 for details.

DVD player

DVD

VIDEO

RIGHT LEFT

S-VIDEO

VIDEO

AUDIO

SUBWOOFER CENTER

DVD

IN

FRONT

DVD

IN

COMPONENT VIDEO

DVD

IN

SURR

(REAR)

R

L

A

B

C

D

RX-8030VBK/RX-7030VBK

• When you connect a DVD player with its analog discrete

output (5.1-channel reproduction) jacks:

To listen to the sound after connection, press DVD MULTI.

Å To component video output

ı To subwoofer output

Ç To center channel audio output

Î To S-video output

‰ To composite video output

Ï To left/right front channel audio output

Ì To left/right surround channel audio output

Note:

When connecting a DVD player to the component video input jacks,

make the component video input setting correctly for AV COMPU

LINK. See page 30 for details.

DVD

VIDEO

RIGHT LEFT

S-VIDEO

VIDEO

AUDIO

SUBWOOFER CENTER

DVD

IN

FRONT

DVD

IN

COMPONENT VIDEO

DVD

IN

SURR

(REAR)

R

L

R

L

A

B

C

D

E F G

RX-8030VBK/RX-7030VBK

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM15

16

English

DIGITAL IN

DIGITAL 1 (DVD)

DIGITAL 2 (CD)

DIGITAL 3 (TV)

DIGITAL 4 (CDR)

PCM/ DOLBY DIGITAL

/ DTS

DIGITAL OUT

Digital Connections

This receiver is equipped with four DIGITAL IN terminals—one

digital coaxial terminal and three digital optical terminals—and one

DIGITAL OUT (optical) terminal on the rear.

• For RX-8030VBK: Another digital optical input terminal is

located on the front panel (see page 13).

IMPORTANT:

• When connecting a DVD player, digital TV broadcast tuner or DBS

tuner using the digital terminals, you also need to connect it to the

video jacks on the rear. Without connecting it to the video jacks, you

can view no playback picture.

• After connecting the components using the DIGITAL IN terminals,

set the following correctly if necessary.

– Set the digital input (DIGITAL IN) terminal setting correctly. For

details, see “Setting the Digital Input Terminals” on page 29.

– Select the digital input mode correctly. For details, see “Selecting

the Analog or Digital Input Mode” on page 19.

Notes:

• When shipped from the factory, the DIGITAL IN terminals have

been set for use with the following components:

– DIGITAL 1 (coaxial): For DVD player

– DIGITAL 2 (optical): For CD player

– DIGITAL 3 (optical): For digital TV broadcast tuner

– DIGITAL 4 (optical): For CD recorder

• When you want to operate the CD player or CD recorder, (or MD

recorder: only for RX-8030VBK) using the COMPU LINK remote

control system, connect the target component also as described in

“Analog Connections” (see pages 12 and 13).

• When you want to operate a DVD player using the AV COMPU

LINK remote control system (see page 42), connect the DVD

player also as described in “Analog Connections” (see page 15).

Digital input terminals

You can connect any digital components having coaxial or optical

digital output terminal.

Digital output terminal

You can connect any digital components which have an optical

digital input terminal.

Digital coaxial cable (not supplied)

between digital coaxial terminals

Digital optical cable (not supplied)

between digital optical terminals

Before connecting a digital

optical cable, unplug the

protective plug.

When the component has a digital

optical output terminal, connect it to the

DIGITAL 2 (CD), DIGITAL 3 (TV) or

DIGITAL 4 (CDR) terminal, using a

digital optical cable (not supplied).

When the component has a digital

coaxial output terminal, connect it to

the DIGITAL 1 (DVD) terminal, using a

digital coaxial cable (not supplied).

When the digital recording

equipment such as an MD recorder

and CD recorder has a digital

optical input terminal, connecting it

to the DIGITAL OUT terminal

enables you to perform digital-to-

digital recording.

Digital optical cable (not supplied)

between digital optical terminals

Note:

The digital signal format transmitted through the DIGITAL OUT

terminal is the same as that of the input signal. This means that when

the DTS Digital Surround signals are input, the DTS Digital Surround

signals are transmitted.

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all

connections have been made.

Plug the power cord into an AC outlet.

Keep the power cord away from the

connecting cables and the antenna. The

power cord may cause noise or screen interference.

Note:

The preset settings such as preset channels and sound adjustment

may be erased in a few days in the following cases:

– When you unplug the power cord.

– When a power failure occurs.

CAUTIONS:

• Do not touch the power cord with wet hands.

• Do not pull on the power cord to unplug the cord. When unplugging

the cord, always grasp the plug so as not to damage the cord.

01-16_8030&7030[C]7.pm6 03.2.13, 2:51 PM16

La page charge ...

JVC RX-7030VBK Instructions For Use Manual

Ce manuel convient également à

JVC RX-7030VBK Instructions For Use Manual

dans d''autres langues

Documents connexes

Autres documents