Smooth Fitness 835BT Manuel utilisateur

USER’S MANUAL

8.35BT MOTORIZED TREADMILL

USER WEIGHT LIMITATION: 400lbs (183kgs).

SERIAL NUMBER (found on frame):

REV2013

2

835BT TREADMILL

PRECAUTIONS

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions

and information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are

adequately informed of all warnings and precautions.

 Use the treadmill only as described in this manual.

 Place on a level surface, with 6 feet 2 X1m of clearance behind it. Do not place the treadmill on any surface that blocks air

openings. To protect the floor or carpet from damage, place a mat under the treadmill.

 When choosing a location for the treadmill be sure that the location and position permit access to a plug.

 Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near

water.

 Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

 Keep children under the age of 12 and pets away from the treadmill at all times.

 The treadmill should not be used by persons weighing more than 400LBS (183 Kgs).

 Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill.

Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both

men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in

sandals.

 When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same

circuit.

 Always straddle the belt and allow it to start moving before stepping onto the belt.

 Always examine your treadmill before using to ensure all parts are in working order.

 Allow the belt to fully stop before dismounting.

 Never insert any object or body parts into any opening.

 Follow the safety information in regards to plugging in your treadmill.

 Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not

operate the treadmill with a damaged or frayed power cord.

 Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an

authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these

instructions will void the treadmill warranty.

 Never leave the treadmill unattended while it is running.

 Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.

 Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from

children.

www.smoothfitness.com

3

PRECAUTIONS

Pour réparations futures ou questions connexes :

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Précautions:

AVERTISSEMENT : Pour réduire les risques de brûlures, d’incendie, de choc électrique ou de blessures aux personnes, lire les

précautions importantes et l’information suivantes avant de se servir du tapis roulant. Il revient au propriétaire de s’assurer que tous

les utilisateurs de ce tapis ont bien été informés de tous les avertissements et précautions.

 Utiliser le tapis seulement comme il est décrit dans ce manuel.

 Le placer sur une surface plane, en laissant 2X1m d’espace libre en arrière. Ne pas placer le tapis roulant sur une surface

qui bloque les ouvertures d’air.

 Pour protéger le plancher ou un tapis de dommages, placer un petit tapis sous le tapis roulant.

 Choisir pour le tapis roulant un emplacement et une position qui permettent d’avoir accès à une prise murale.

 Garder le tapis roulant à l’intérieur, à un endroit sans humidité ni poussière. Ne pas mettre le tapis roulant dans un garage,

sur une terrasse couverte ou près de l’eau.

 Ne pas faire fonctionner le tapis roulant pendant la vaporisation de produits aérosol ou l’administration d’oxygène.

 Ne pas laisser les enfants de moins de 12 ans et les animaux s’approcher du tapis roulant.

 Le tapis roulant ne doit pas être utilisé par des personnes pesant plus de 183 kg (400 lb).

 Il ne doit jamais y avoir plus d’une personne sur le tapis à la fois. Porter des vêtements d’exercice appropriés pour utiliser

le tapis roulant. Ne pas porter de vêtements lâches qui pourraient être pris dans le tapis roulant. Les vêtements de soutien

athlétiques sont recommandés tant pour les hommes que pour les femmes. Porter toujours des chaussures d’athlétisme.

Ne pas être pieds nus, ou porter seulement des chaussettes ou des sandales lors de l’utilisation du tapis roulant.

 Brancher le cordon d’alimentation dans un circuit avec mise à la terre. Aucun autre appareil ne doit être sur le même

circuit.

 Toujours enjamber le tapis et le laisser commencer à rouler avant de monter dessus.

 Toujours examiner votre tapis roulant avant de l’utiliser pour s’assurer que toutes les pièces fonctionnent correctement.

 Laisser le tapis s’arrêter complètement avant de descendre.

 Ne jamais insérer d’objets ou de parties du corps dans une ouverture.

 Suivre les directives de sécurité en ce qui concerne le branchement de votre tapis roulant.

 Garder le cordon d’alimentation éloigné des roues inclinées et ne pas faire passer le cordon d’alimentation sous votre

tapis roulant. Ne pas faire fonctionner le tapis roulant si le cordon d’alimentation est endommagé ou effiloché.

 Débrancher toujours le tapis roulant avant de le nettoyer ou de le réparer.

 Toute réparation au tapis doit être effectuée par un réparateur agréé, à moins d’autorisation ou de directives contraires du

fabricant. Le non-respect de ces instructions annulera la garantie du tapis roulant.

 Ne jamais laisser le tapis roulant sans surveillance lorsque la clé de sécurité est insérée.

 Utiliser la « clé de sécurité » pour faire fonctionner le tapis roulant et s’assurer qu’elle est accrochée aux vêtements des

utilisateurs.

 Retirer la « clé de sécurité » et la ranger dans un endroit sûr lorsque le tapis roulant n’est pas en fonction. Garder la « clé

de sécurité » hors de la portée des enfants.

4

835BT TREADMILL

POWER REQUIREMENTS

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE

PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT

THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and

noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of

treadmill damage, always use a surge protector (not included) with your treadmill.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a

UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an

electrical rating 120VAC, 15 amps.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric

current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding

conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing

below.

GFCI outlets and GFCI / AFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI / AFCI

Circuit Breakers may cause this equipment to function improperly.

www.smoothfitness.com

5

POWER REQUIREMENTS

Alimentation :

UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L’ÉQUIPEMENT POURRAIT PROVOQUER UN

CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SAVOIR

SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI

ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN

PROFESSIONNEL.

Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique.

Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des

pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un

limiteur de surtension (non inclus) avec votre tapis roulant.

Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de

surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de

400 V ou moins et une tension électrique de 110 V C.A., 15 A.

Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre

résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon

électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un

limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre

conformément à tous les codes locaux et ordonnances.

Ce produit doit être utilisé avec un circuit nominal de 110 volts et à une fiche de mise à la terre qui ressemble à celle illustrée ci-

dessous.

Prises GFCI électriques et disjoncteurs GFCI / AFCI ne sont pas recommandées pour une utilisation sur ce produit. Prises GFCI

électriques et disjoncteurs GFCI / AFCI peut causer cet équipement de fonctionner correctement.

6

835BT TREADMILL

BEFORE YOU BEGIN

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes and Supplied Hardware lists on

page 7 for a full count of the parts included. If you are missing any parts or have any questions contact us directly

at 888-800-1167

Gather your tools:

Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit

properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is

free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a

comfortable amount of free area around the unit for unobstructed operation.

Invite a friend:

Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product. If you weigh more than 400LBS (Approx. 183 Kgs). It is

not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown

here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:

The safety level can be maintained only if it is examined for damage and wear.

Replace any defective components immediately and stop all use of the equipment until repaired.

Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.

Dismount from the equipment only after all parts have stopped.

Always check the wear and tear components like pulley, belts, etc.…To prevent injury.

There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately

by actuating the emergency stop for emergency dismount.

www.smoothfitness.com

7

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

Millimeters

Allen socket head half thread screw

（M8*55*20） 6pcs

Phillips Screwdriver /

Wrench 1pcs

T Allen wrench( S6) 1pcs

Allen socket head full thread screw

（M8*15） 2pcs

Phillips head self-tapping

screw ST4*20 4pcs

Allen socket head full thread

screw (M8*50*20) 4pcs

Phillips head screw M3*28 4pcs

Treadmill Base

Silicon bottler

Manual

Hardware pack

Safety key

Base frame cover

Console

Upright Posts

Handlebars

8

835BT TREADMILL

COMPLETE PARTS LIST

Item No.

Description

Qty.

835BT-1

Base frame

1

835BT-2

Platform frame

1

835BT-3

Incline frame

1

835BT-4

Motor base frame

1

835BT-5

Upright post (left)

1

835BT-6

Upright post (right)

1

835BT-7

Console base frame

1

835BT-8

Pedal base frame

1

835BT-9

Foldable plate (left)

1

835BT-10

Foldable plate (right)

1

835BT-11

Wheel connector plate

2

835BT-12

Bushing for limited space

1

835BT-13

Allen C.K.S. half thread screw M10×55×20

2

835BT-14

Allen C.K.S. half thread screw M10×35×20

1

835BT-15

Allen C.K.S. full thread screw M10×60×20

1

835BT-16

Allen C.K.S .half thread screw M8×80×20

1

835BT-17

Allen C.K.S. half thread screw M8×55×20

6

835BT-18

Allen C.K.S. half thread screw M8×60×20

2

835BT-19

Allen C.K.S. half thread screw M8×50×20

5

835BT-20

Allen C.K.S. half thread screw M8×30×20

4

835BT-21

Allen socket full thread screw M8×10

14

835BT-22

Allen socket full thread screw M8×75

2

835BT-23

Allen socket full thread screw M8×65

1

835BT-24

Allen socket full thread screw M8×15

2

835BT-25

Allen socket full thread screw M8×20

6

835BT-26

Hex full thread screw M8×75

1

835BT-27

Philips full thread screw M8×25

2

835BT-28

Philips full thread screw M6×25

4

835BT-29

Philips C.K.S.screw M5×20

9

835BT-30

Philips C.K.S. full thread screw M4×20

4

835BT-31

Philips C.K.S. full thread screw M4×10

13

835BT-32

Philips C.K.S.self-tapping screw ST4×15

40

835BT-33

Philips C.K.S. full thread screw M5×10

8

835BT-34

Base frame cover (left)

1

835BT-35

Philips self-tapping screw ST4×15

8

835BT-36

Philips self-tapping screw ST3×10

2

835BT-37

Flat washer Φ8.2×Φ25×t2.0

4

835BT-38

Flat washer Φ10

3

835BT-39

Flat washer Φ8

20

835BT-40

Flat washer Φ6×Φ20×t2.0

6

www.smoothfitness.com

9

COMPLETE PARTS LIST

Item No.

Description

Qty.

835BT-41

Washer Φ5

1

835BT-42

Self-locking nut M10

3

835BT-43

Self-locking nut M8

8

835BT-44

Ferrite bushing Φ17*Φ10*31

2

835BT-45

Fan fix base

1

835BT-46

Running belt

1

835BT-47

Console housing

1

835BT-48

Back cover for the console

1

835BT-49

Safety key

1

835BT-50

PU grip

2

835BT-51

Motor cover (left)

1

835BT-52

Motor cover (middle)

1

835BT-53

Motor cover (right)

1

835BT-54

Main overlay

1

835BT-55

Wire coater

1

835BT-56

Spring

1

835BT-57

Back cover for the console

1

835BT-58

Cable ring

1

835BT-59

Washer limited the space

2

835BT-60

End cap

2

835BT-61

Transmission belt

1

835BT-62

Side rail

2

835BT-63

Rear cover (left)

1

835BT-64

Rear cover (right)

1

835BT-65

Foot cover

2

835BT-66

Handle pulse with easy button (incline)

1

835BT-67

Base frame cover (right)

1

835BT-68

Wheel (1) Φ62*Φ12.5*T22

2

835BT-69

Wheel (2) Φ46*Φ8*T18.5

4

835BT-70

rubber

2

835BT-71

Motor base frame gasket

4

835BT-72

Shock absorber (1)

4

835BT-73

Shock absorber (2)

2

835BT-74

Cable guider

1

835BT-75

Foam grip

2

835BT-76

Binder

1

835BT-77

Switch

1

835BT-78

Fuse

1

835BT-79

Controller

1

835BT-80

Power cord

1

10

835BT TREADMILL

COMPLETE PARTS LIST

Item No.

Description

Qty.

835BT-81

Filter

1

835BT-82

Choke

1

835BT-83

Transformer

1

835BT-84

Motor

1

835BT-85

Incline motor

1

835BT-86

Ferret bushing∮33X∮14X33

2

835BT-87

Ferret bushing ∮20X∮9X32

4

835BT-88

Hydraulic

2

835BT-89

running deck

1

835BT-90

Front roller

1

835BT-91

rear roller

1

835BT-92

Main cable

1

835BT-93

Controller cable

1

835BT-94

Allen C.K.S.full thread screw M8×15

4

835BT-95

Bolt welding M8×65

1

835BT-96

Fan

2

835BT-97

Plastic bushing

2

835BT-98

Central side rail

2

835BT-99

Wire binder

1

835BT-100

vent hole (right)

1

835BT-101

vent hole (left)

1

835BT-102

Wire

1

835BT-103

Philips C.K.S. self-tapping screw M4*40

2

835BT-104

Philips C.K.S. full thread screw M3*28

4

835BT-105

Spring washer

2

835BT-106

Philips full thread screw M5*15

2

835BT-107

Philips full thread screw ST4×12

14

835BT-108

speaker

2

835BT-109

Speed sensor

1

www.smoothfitness.com

11

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED

12

835BT TREADMILL

ASSEMBLY – PLEASE READ ALL STEPS BEFORE BEGINNING YOUR WORK.

Caution- Do not pick up the treadmill from the front. There are rotating frame

parts that may pinch your hands or feet.

STEP1: Remove the treadmill and its components from the packaging

NOTE: Make sure all wires are recessed into the frame. DO NOT trap or

Pinch the wires. Keep hands clear of all moving components.

CAUTION: WHEN UNPACKING THE TREADMILL

THE FRAME MAY ROTATE. DO NOT PICK UP THE

UNIT FROM THE FRONT. HANDS MAY BE PINCHED

BETWEEN THE FRAME.

www.smoothfitness.com

13

ASSEMBLY – PLEASE READ ALL STEPS BEFORE BEGINNING YOUR WORK.

STEP 2: Attach the Left and Right Uprights to the Base Frame

NOTE: Do not fully tighten the bolts at this time.

1). Locate the data cable. Connect the lower data cable( located in the treadmill

base frame) to the middle data cable (located in the right upright)

2). Slide the right upright on to the base frame. Secure the right upright to the base

frame by using 2 x M8*15mm Allen Head bolts, to the front side of the upright and

3x M8*55mm*20mm Allen Head bolts to the side of upright.

3). Repeat the above process for the left side.

M8*15mm

4

M8*55mm*20mm

6

Caution Pinch point! Do not pinch wires between the frame when placing the upright on to the base frame.

ONLY HAND TIGHTEN THE BOLTS

!!Pinch Points!!

14

835BT TREADMILL

ASSEMBLY

STEP 3: Attach the Computer Console

Caution: Pinch point

1). Connect the middle data cable from the right upright to the upper data cable

from the console.

2). Place the console on to the right and left uprights. Secure the console to the

uprights by using 4 x M8*50*20mm bolts

4). Completely tighten all bolts from step 2 and 3 now.

M8*50*20mm

X4

Caution Pinch point! Do not pinch wires between the frame during console assembly.

Tighten all bolts and fasteners

now

!!Pinch Points!!

www.smoothfitness.com

15

ASSEMBLY

Step4: Attach the Base Frame Covers

1). Place the left base frame cover over the left upright and slide it downward

towards the floor.

2). Align the 2 holes in the base frame covers with the two screw holes in the base

frame.

3). Secure the cover by using 2 x ST4*20mm Screw through the base frame cover

and thread into the base frame.

4). Repeat the process for the right side.

5). Tighten all fasteners now.

ST4*20mm

X4

16

835BT TREADMILL

ASSEMBLY

STEP 5: Attach the Handlebar Covers to the Computer Console

1). Place the two handle bar covers on to the left and right handlebars.

2). Secure the cover tot the handle bars by using 4 x M3*28mm screws

3). Fully tighten all hardware now

M3*28mm

X4

www.smoothfitness.com

17

ASSEMBLY

STEP 6:

Insert Safety Key (209) into Bottom Center of Console prior to operation. Your

treadmill will not Function without the safety key.

X1

Safety Key Pad

If the safety key is not present the treadmill will not function

18

835BT TREADMILL

LEVELING AND MOVING

How to fold and unfold the treadmill:

Your treadmill can be folded up and unfold for space saving storage. To do this follow the instructions here:

Fold Up

1. To fold the deck you first need to bring the treadmill

to the lowest incline level and then remove the

power cord

2. Lift the deck up from the rear of the treadmill and

fold up until it locks in place. TO PREVENT INJURY

BE SURE YOU HAVE A FIRM HOLD WHEN

RAISING THE DECK.

3. You will hear a “click” sound as the lock engages.

Unfold

You can unfold the treadmill from the upright position:

1. Begin by standing behind and supporting the deck

with your hands. Next release the lock with your foot

by stepping on the release lever. TO PREVENT

INJURY BE SURE YOU HAVE A FIRM HOLD ON

THE DECK BEFORE RELEASING THE LOCK.

2. While supporting the treadmill deck, slowly lower the

deck until the deck starts to lower on its own. The

deck will lower slowly until it rests on the ground.

DO NOT STAND UNDER THE DECK AS IT

LOWERS. KEEP ALL OBJECTS CLEAR AS THE

TREADMIL IS BEING LOWERED.

Horizontal Adjustment

An uneven floor or improper stabilizer level can cause

the treadmill to wobble during use as well as the incline

adjustment to function incorrectly. Please follow the

procedure described below to make sure the treadmill

stabilizer is adjusted correctly prior to use. You may

need the assistance of another person to perform this

adjustment.

First locate the two adjustable stabilizers under the

base frame. Then simply rotate them in or out to

adjust the level of the treadmill. When properly

adjusted the treadmill should sit firmly on both

stabilizers and all cushions.

www.smoothfitness.com

19

MAINTAINENCE

HOW TO MAINTAIN YOUR TREADMILL:

Proper maintenance is very important to ensure your treadmill is always in top working condition. Improper maintenance could

cause damage or shorten the life of your treadmill and void the LIMITED WARRANTY coverage.

 Important: DO NOT use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids

away and keep it out of direct sunlight.

 Inspect and tighten all parts of the treadmill regularly. Replace any damaged or worn parts immediately.

BELT ADJUSTMENT:

The running belt has been properly adjusted at the factory. However transportation, uneven flooring or other

unpredicted reasons could cause the belt to shift off center resulting in the belt rubbing with the plastic side rail or end

caps and possibly causing damage. To adjust the belt back to its proper position please follow the directions below:

1. If your belt tends to walk to the right, rotate the right tension bolt clockwise. We recommend adjustments of

1/4 turn at a time, and follow with a test. If your belt continues to walk to the right, simply adjust the left belt

tension bolt by turning it 1/4 turn counterclockwise, and follow with a test.

2. If your belt tends to walk to the left, rotate the left tension bolt clockwise 1/4 turns at a time, and follow with a

test. If the belt continues to walk to the left, simply adjust the right tension bolt counterclockwise.

3. If your belt appears to be loose, simply tighten both bolts evenly 1/4 turn. If it appears tight, simply loosen

both bolts evenly 1/4 turn.

Right and left tension bolts are located at the rear of the treadmill.

DECK LUBRICATION:

The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be

checked periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be

lubricated usually within 3 months.

Smooth Fitness recommends lubricating the walking deck a minimum of twice a year for light use (2 days a week) and

four times a year for heavier use(3 times a week multiple users)

Please visit www.smoothfitness.com for approved maintenance supplies

20

835BT TREADMILL

MAINTAINENCE

To apply lubricant under the walking belt:

1. Position the walking belt so that the seam is located on top and in center of the walking board.

2. Insert the nozzle of the lubricant container under the belt

3. While lifting the side of the walking belt, position the nozzle between the walking belt and the board

approximately 15 cm (6 inches) from the front of the treadmill. Apply the silicone lubricant to the walking

board, moving from the front of the treadmill to the rear. Repeat this on the other side of the belt. Note: it is

important to get the lubricant as far to the center of the walking board as possible.

4. Allow the silicone to "set" for 1 minute before using the treadmill.

Apply lubricant from front to back.

CLEANING:

Routine cleaning of your treadmill will extend the product's life.

 Warning: To prevent electrical shock, be sure the power to the treadmill is OFF and the power cord is

unplugged from the wall electrical outlet before attempting any cleaning or maintenance.

 Important: DO NOT use abrasives or solvents to clean the treadmill. To prevent damage to the computer,

keep liquids away and keep it out of direct sunlight.

 After each workout: Wipe off the console and other treadmill surfaces with a clean, water dampened soft

cloth to remove excess perspiration.

 Weekly: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt

and eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.

Note: when lubricating the belt, make sure the treadmill is located on a surface that can

be easily cleaned. After lubricating your treadmill running belt, clean any excess silicone

off the belt and frame.

La page charge ...

Smooth Fitness 835BT Manuel utilisateur

Smooth Fitness 835BT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents