Randell 9000-290/9000F-290 Manuel utilisateur

This manual provides information on installation, operating,

maintenance, trouble shooting & replacement parts for:

OPERATOR MANUAL

IMPORTANT INFORMATION, KEEP FOR OPERATOR

PART NUMBER PP MNL1710, REV C (10/17)

WORKTOPS/

UNDERCOUNTER SERIES:

9404F-290

9402F-290

9404F-32-290

9802F-290

9302F-290

9301F-290

• Freezer (-5ºF to 0ºF)

• Refrigerator (40ºF)

Information contained in this document is known to be current and accurate at the time

of printing/creation. Uniﬁed Brands recommends referencing our product line websites,

uniﬁedbrands.net, for the most updated product information and speciﬁcations.

1055 Mendell Davis Drive

Jackson, MS 39272

888-994-7636, fax 888-864-7636

uniﬁedbrands.net

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.

READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND

WARNINGS CONTAINED IN THIS MANUAL.

WARNING / FOR YOUR SAFETY

Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this or any other appliance.

WARNING

R290 flammable refrigerant in use. Improper installation,

adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read the installation,

operating and maintenance instructions thoroughly before

installing or servicing this equipment.

NOTIFY CARRIER OF DAMAGE AT ONCE

It is the responsibility of the consignee to inspect the container upon receipt of

same and to determine the possibility of any damage, including concealed dam-

age. Unified Brands suggests that if you are suspicious of damage to make a

notation on the delivery receipt. It will be the responsibility of the consignee to file

a claim with the carrier. We recommend that you do so at once.

Manufacture Service/Questions 888-994-7636.

9402-290

9404-290

9404-32-290

9404-32D-290

2 OM-WORK TOP/UNDERCOUNTER SERIES

Important Operator Notices ......................................................... page 3

Labeling ..................................................................................... page 4-5

Equipment Description .................................................................. page 6

Installation .................................................................................... page 7

Operation ................................................................................ page 8-9

Maintenance ................................................................................ page 10

Troubleshooting ........................................................................... page 11

Service ........................................................................................ page 12

Parts List ................................................................................ page 13-17

Electrical Schematic ............................................................. page 18-22

Service Log ............................................................................ page 23-24

Warranty Policies .................................................................. page 25-27

Table of Contents

OM-WORK TOP/UNDERCOUNTER SERIES 3

IMPORTANT - READ FIRST - IMPORTANT

Congratulations on your recent purchase of Uniﬁed Brands food service equipment, and welcome to the growing family of satisﬁed

Uniﬁed Brands customers.

Our reputation for superior products is the result of consistent quality craftsmanship. From the earliest stages of product design to

successive steps in fabrication and assembly, rigid standards of excellence are maintained by out staff of designers, engineers, and

skilled employees.

Only the ﬁnest heavy-duty materials and parts are used in the production of Uniﬁed Brands brand equipment. This means that each

unit, given proper maintenance will provide years of trouble free service to its owner.

In addition, all Uniﬁed Brands food service equipment is backed by some of the best warranties in the food service industry and by

our professional staff of service technicians.

Retain this manual for future reference.

NOTICE: DUE TO A CONTINUOUS PROGRAM OF PRODUCT IMPROVEMENT, UNIFIED BRANDS RESERVES THE RIGHT TO MAKE CHANGES IN

DESIGN AND SPECIFICATIONS WITHOUT PRIOR NOTICE.

NOTICE: PLEASE READ THE ENTIRE MANUAL CAREFULLY BEFORE INSTALLATION. IF CERTAIN RECOMMENDED PROCEDURES ARE NOT

FOLLOWED, WARRANTY CLAIMS WILL BE DENIED.

MODEL NUMBER _________________________

SERIAL NUMBER _________________________

INSTALLATION DATE ______________________

THE SERIAL NUMBER IS LOCATED IN THE CABINET LEFT SIDE UNDER THE DRAWER TRACK. AN EXAMPLE IS SHOWN BELOW.

SERIAL NUMBER XXXXXXXXX

MODEL NUMBER XXXXXXXXX

DESCRIPTION

4 OM-WORK TOP/UNDERCOUNTER SERIES

The following warning labels will be found on your equipment:

INTERIOR EVAPORATOR COVER

NEAR MACHINE COMPARTMENT AND NAMEPLATE

Labeling

OM-WORK TOP/UNDERCOUNTER SERIES 5

EXTERIOR OF UNIT

NEAR EXPOSED REFRIGERANT TUBING

Labeling

6 OM-WORK TOP/UNDERCOUNTER SERIES

Equipment Description

MODEL

LENGTH

DEPTH

HEIGHT

DOORS

STORAGE CU.

FT.

HP

VOLT

AMPS

NEMA

SHIP WT.

9404F-290 27” 30” 36” (1)27” 5.7 1/4 115/60/1 2.2 5-15P 185

9402F-290 27” 30” 36” (1)27” 5.7 1/4 115/60/1 2.2 5-15P 185

9404F-32-290 32” 32.5” 36” (1)32” 8.6 1/3 115/60/1 2.6 5-15P 252

9802F-290 36” 30” 36” (2)18” 7.87 1/3 115/60/1 2.6 5-15P 220

9301F-290 48” 30” 36” (2)24” 10.8 1/3 115/60/1 2.6 5-15P 265

9302F-290 48” 30” 36” (2)24” 10.8 1/3 115/60/1 2.6 5-15P 265

9402-290 27" 30" 36" (1)27” 5.7 1/4 115/60/1 2.4 5-15P 185

9404-290 27" 30" 36" (1)27” 5.7 1/4 115/60/1 2.4 5-15P 185

9404-32-290 32" 32.5" 36" (1)32” 8.6 1/4 115/60/1 2.4 5-15P 252

9404-32D-290 32" 32.5" 36" (2) DRAWERS 8.6 1/4 115/60/1 2.4 5-15P 252

OM-WORK TOP/UNDERCOUNTER SERIES 7

Installation

SELECTING A LOCATION FOR YOUR NEW UNIT

The following conditions should be considered when selecting a location for your unit:

1. Floor and Countertop Load: The area on which the unit will rest must be level, free

of vibration, and suitably strong enough to support the combined weights of the unit

plus the maximum product load weight.

2. Clearance: Clearance must be a combined total of at least 1” on back of unit and

open clearance at the top. Do not place any object that can block the ventilation

exhaust from the machine compartment register. Area of equipment must be free of

all combustible materials.

3. Ventilation: The air cooled self contained unit requires a sufﬁcient amount of cool

clean air. Avoid surrounding your unit around other heat generating equipment and

out of direct sunlight. Also, avoid locating in an unheated room or where the room

temperature may drop below 70°F or rise above 100°F.

INSTALLATION CHECKLIST

After the ﬁnal location has been determined, refer to the following checklist prior to

start-up:

1. Check all exposed refrigeration lines to ensure that they are not kinked, dented, or

rubbing together.

2. Check that the condenser and evaporator fans rotate freely without striking any

stationary members.

3. Unit must be properly leveled; check all legs or casters to ensure they all are in

contact with the ﬂoor while maintaining a level work surface. Adjusting bullet

feet heights or shimming casters may be necessary if the ﬂoor is not level. NOTE:

Damage to equipment may result if not followed. Uniﬁed Brands is not responsible

for damage to equipment if improperly installed.

4. Allow unit time to cool down to temperature. If temperature adjustments are required,

the control is located on the front panel. Conﬁrm that the unit is holding the desired

temperature.

5. Refer to the front of this manual for serial number location. Please record this

information in your manual on page 3 now. It will be necessary when ordering

replacement parts or requesting warranty service.

6. Before putting in food, allow your unit to operate for approximately two (2) hours so

that interior of the unit is cooled down to storage temperature.

7. Check drawer to ensure the drawer slides freely and fully extends along with seating

into the cabinet properly when closed.

ELECTRICAL SUPPLY

Any wiring should be done by a qualiﬁed electrician in accordance with all national and

local electrical codes. A properly wired and grounded outlet will assure proper operation.

Please consult the data tag attached to the compressor to ascertain the correct electrical

requirements. Supply voltage and amperage requirements are located on the serial

number tag (see page 3 for location).

CAUTION!

THIS UNIT CONTAINS R290 FLAMMABLE

REFRIGERANT. USE CAUTION WHEN

HANDLING MOVING AND USE OF THE

REFRIGERATOR OR FREEZER. AVOID

DAMAGING THE REFRIGERANT TUBING OR

INCREASE THE RISK OF A LEAK.

FAILURE TO FOLLOW INSTALLATION

GUIDELINES AND RECOMMENDATIONS MAY

VOID THE WARRANTY ON YOUR UNIT.

IT IS IMPORTANT THAT YOUR UNIT HAS

ITS OWN DEDICATED LINE. CONDENSING

UNITS ARE DESIGNED TO OPERATE WITH

A VOLTAGE FLUCTUATION OF PLUS OR

MINUS 10% OF THE VOLTAGE INDICATED

ON THE UNIT DATA TAG. BURN OUT OF A

CONDENSING UNIT DUE TO EXCEEDING

VOLTAGE LIMITS WILL VOID THE WARRANTY.

THE DANFOSS CONTROLLER HAS LOW

VOLTAGE PROTECTION AND WILL NOT

OUTPUT VOLTAGE TO THE COMPRESSOR IF

VOLTAGE IS LESS THAN 104V.

THIS UNIT IS INTENDED FOR USE IN

LABORATORIES IN COMMERCIAL,

INDUSTRIAL, OR INSTITUTIONAL

OCCUPANCIES AS DEFINED IN THE SAFETY

STANDARD FOR REFRIGERATION SYSTEMS,

ASHRAE 15.

8 OM-WORK TOP/UNDERCOUNTER SERIES

Operation

Allow unit to operate for approximately two (2) hours before placing in food.

AMBIENT CONDITIONS

Unit is designed for normal operating temperatures between 70-100°F. Operating

outside of those temperatures may cause premature product wear or failure.

Uniﬁed Brands has attempted to preset the temperature control to ensure that your

unit runs at an optimum temperature, but due to varying ambient conditions, including

elevation, food type and your type of operation, you may need to alter this temperature

using control adjustment until desired temperature is reached.

DANFOSS CONTROLLER OPERATION

LED FUNCTION

Compressor energized & Evaporator fan de-energized

Defrost in progress

Fans delay after defrost completion

Evaporator fan energize

An alarm is occurring

ºC / ºF Temperature unit

POWER ON / OFF: Press and hold the power button until LED display turns On / Off

MANUAL DEFROST: Press and hold “Defrost” Button

CHANGE SET POINT: To raise temperature

1. Press and hold “

” to access set point.

2. When set point start ﬂashing, Press “

” to adjust set point

3. After 30 seconds, the display automatically reverts to showing the current

temperature

CHANGE SET POINT: To lower temperature

1. Press and hold “v” to access set point

2. When set point start ﬂashing, Press “v” to adjust set point

3. After 30 seconds, the display automatically reverts to showing the current

temperature

POWER ON / OFF

MANUAL DEFROST

CHANGE SET POINT

OM-WORK TOP/UNDERCOUNTER SERIES 9

Operation

CHANGE FROM ºF /ºC :

1. Press the up/down buttons simultaneously for 5 seconds to access the menu.

2. Password is requested. Password is 000.

3. Press the bottom left button to OK the password.

4. Using the up/down buttons, navigate to the “diS” level. Press the bottom left button

to OK the selection.

5. Using the up/down buttons, navigate to the “CFu” level. Press the bottom left button

to OK the selection.

a. “-F” designates Fahrenheit.

b. “-C” designates Celsius.

6. Press the top left button repeatedly to return to exit and return to the home screen.

DRAWER / DOOR ALARM: Acknowledging Alarms – Visual Display Only

1. After 2 minutes the display will ﬂash the alarm message “dor”

2. Press any button to acknowledge alarm

DRAWER / DOOR ALARM: Door Alarm Activation – If audible alarm is wanted

1. Press the up/down buttons simultaneously for 5 seconds to access the menu.

2. Password is requested. Password is 000.

3. Press the bottom left button to OK the password.

4. Using the up/down buttons, navigate to the “ALA” level. Press the bottom left button

to OK the selection.

5. Using the up/down buttons, navigate to the “Abd” level. Press the bottom left button

to OK the selection.

a. “0” Disables the alarm.

b. Any other number is the number of minutes before the buzzer sounds after the

drawer is opened.

6. Press the top left button repeatedly to return to exit and return to the home screen.

10 OM-WORK TOP/UNDERCOUNTER SERIES

Maintenance

Uniﬁed Brands strongly suggests a preventive maintenance program which would include

the following Monthly procedures:

1. Clean fan blades on the condensing unit and evaporator assembly.

2. Clean all gaskets on a weekly if not daily basis with a solution of warm water and a

mild detergent to extend gasket life.

3. Lubricate door hinges with lithium grease.

RECOMMENDED CLEANERS FOR YOUR STAINLESS STEEL INCLUDE THE FOLLOWING:

JOB CLEANING AGENT COMMENTS

Routine cleaning

Soap, ammonia,

detergent Medallion

Apply with a sponge or cloth

Fingerprints and smears Arcal 20, Lac-O-Nu, Ecoshine Provides a barrier ﬁlm

Stubborn stains and

discoloration

Cameo, Talc, Zud,

First Impression

Rub in the direction of the

polish lines

Greasy and fatty acids, blood,

burnt-on foods

Easy-Off, Degrease It,

Oven Aid

Excellent removal on all

ﬁnishes

Grease and Oil

Any good commercial

detergent

Apply with a sponge or cloth

Restoration/Preservation Beneﬁt, Super Sheen Good idea monthly

Reference: Nickel Development Institute, Diversey Lever, Savin, Ecolab, NAFEM

Proper maintenance of equipment is the ultimate necessity in preventing costly repairs. By

evaluating each unit on a regular schedule, you can often catch and repair minor problems

before they completely disable the unit and become burdensome on your entire operation.

For more information on preventive maintenance, consult your local service

company or CFESA member. Most repair companies offer this service at very reasonable

rates to allow you the time you need to run your business along with the peace of mind

that all your equipment will last throughout its expected life. These services often offer

guarantees as well as the ﬂexibility in scheduling or maintenance for your convenience.

For a complete listing of current Uniﬁed Brands ASA please visit www.uniﬁedbrands.net.

Uniﬁed Brands believes strongly in the products it manufactures and backs those products

with one of the best warranties in the industry. We believe with the proper maintenance and

use, you will realize a proﬁtable return on your investment and years of satisﬁed service.

DO NOT USE SHARP UTENSILS AND/OR

OBJECTS.

CAUTION

DO NOT USE ABRASIVE CLEANING

SOLVENTS, AND NEVER USE HYDROCHLORIC

ACID (MURIATIC ACID) ON STAINLESS STEEL.

DO NOT USE STEEL PADS, WIRE BRUSHES,

SCRAPERS, OR CHLORIDE CLEANERS TO

CLEAN YOUR STAINLESS STEEL.

DO NOT PRESSURE WASH EQUIPMENT AS

DAMAGE TO ELECTRICAL COMPONENTS

MAY RESULT.

OM-WORK TOP/UNDERCOUNTER SERIES 11

Troubleshooting

This unit is designed to operate smoothly and efﬁciently if properly maintained. However, the following is a list of checks to make in

the event of a problem. Wiring diagrams are found at the end of this manual.

SYMPTOM POSSIBLE CAUSE PROCEDURE

Unit does not run

No power to unit Plug in unit

Control in OFF position Turn controller on

Faulty control Call for service at 888-994-7636

Unit too cold Incorrect set point Adjust control set point

Unit too warm

Door / drawer ajar Ensure door / drawer is fully closed

Gasket torn or out of place Inspect the gasket for wear and position

Incorrect set point Adjust control set point

Warm product introduced to cabinet Pre-chill product 37ºF or 3ºF degree for freezer

Ice on the coil Initiate manual defrost

Unit noisy Ice on the coil Initiate manual defrost

Unit does not defrost Excessive ice on the coil Initiate manual defrost

When in doubt, turn unit off and call for service at 888-994-7636.

12 OM-WORK TOP/UNDERCOUNTER SERIES

Service

This piece of equipment uses a R290 Refrigeration system. This equipment has been

clearly marked on the serial tag the type of refrigerant that is being used. There is also a

warning labels stating that the unit contains R290 refrigerant.

No smoking or open ﬂames when servicing this equipment. If needed, use a CO

2

or

dry=power type ﬁre extinguisher

Only authorized service technician, certiﬁed in R290 system should service this equipment.

MANIFOLD SET

A R134A manifold set can be used for servicing this equipment.

REFRIGERANT RECOVERY

Follow all national and local regulations for R-290 refrigerant recovery.

LEAKING CHECKING AND REPAIR

Leak check an R-290 system the same way you would an R-134a or R-404A system with

the following exceptions.

1. Do not use a Halid leak detector on a R290 system.

2. Electronic leak detector must be designated speciﬁcally for combustible gas.

Use of a bubble solution or an ultrasonic leak detector are acceptable.

When repairing a leak, it is recommended using oxygen free dry nitrogen with a trace gas

not exceeding 200PSI.

When accessing an R290 system, piercing valves are not to remain on the equipment in

a permanent manner. After charge is recovered, Schrader valves are to be installed on the

process stubs. Proper charge is to be weighed into the system and the system is to be

leak checked afterwards.

The R290 equipment must have red process tubes and other devices through which the

refrigerant is serviced, such as any service port. This color marking must remain on the

equipment. If marking is removed, it must be replace and extend at least 2.5 centimeters

(1”) from the compressor.

CHARGING

Follow the charge amount speciﬁed on the data tag. It is recommended to use the shortest

hoses possible to prevent undercharging.

• Ensure the system is sealed and leak checked

• Evacuate system to a minimum 500 micron

• Weigh in correct charge

• Leak check the system again

• Bleed the refrigerant from the high side hose to the low side hose

• Disconnect the hoses

• Remove line taps

CAUTION!

COMPONENT PARTS SHALL BE REPLACED

WITH LIKE COMPONENTS. SERVICE WORK

SHALL BE DONE BY FACTORY AUTHORIZED

SERVICE PERSONNEL, SO AS TO MINIMIZE

THE RISK OF POSSIBLE IGNITION DUE TO

INCORRECT PARTS OR IMPROPER SERVICE.

OM-WORK TOP/UNDERCOUNTER SERIES 13

Parts List

ITEM PART # DESCRIPTION 9404-290 9404-32-290 9404F-290 9404F-32-290 9802F-290 9302F-290

1 RP DOR101 DOOR - RIGHT - 18" - - - - X -

1 RP DOR103 DOOR - RIGHT - 24" - - - - - X

1 RP DOR102 DOOR - LEFT - 18" - - - - X -

1 RP DOR104 DOOR - LEFT - 24" - - - - - X

1 RP DOR105 DOOR - RIGHT - 27" X - X - - -

1 RP DOR106 DOOR - LEFT - 27" X - X - - -

1 RP DOR107 DOOR - RIGHT - 32" - X - X - -

1 RP DOR108 DOOR - LEFT - 32" - X - X - -

2 RP HNG026 HINGE, STRAP L BRACKET BOTTOM X X X X X X

3 RP HNG9901 HINGE ASSY, SELF CLOSING, RIGHT X X X X X X

3 RP HNG9902 HINGE ASSY, SELF CLOSING, LEFT X X X X X X

4 IN GSK1020 GASKET, PUSH-IN (LEFT/RIGHT DOORS) - - - - - X

4 IN GSK1025 GASKET, PUSH-IN (LEFT/RIGHT DOORS) - - - - X -

4 IN GSK1030 GASKET, PUSH-IN (LEFT/RIGHT DOORS) X - X - - -

4 IN GSK1032 GASKET, PUSH-IN (LEFT/RIGHT DOORS) - X - X - -

5 RP HDL037 DOOR HANDLE X X X X X X

6 HD BSH050 BUSHING, NYLON DOOR X X X X X X

7 RP HNG035 HINGE, TOP DOOR RH CHANNEL X X X X X X

8 RP HNG034 HINGE, TOP DOOR LH CHANNEL X X X X X X

14 OM-WORK TOP/UNDERCOUNTER SERIES

Parts List

ITEM PART # DESCRIPTION 9404-290 9404-32-290 9404F-290 9404F-32-290 9802F-290 9302F-290

1 RF CMP1604 COMPRESSOR, EMBRACO X X X - - -

1 RFCMP1701 COMPRESSOR, EMBRACO - - - X X X

1

RF CMP1604SC

COMPRESSOR, START PARTS X X X - - -

1 RFCMP1701SC COMPRESSOR, START PARTS - - - X X X

2 HD PIN0601 PIN, HAIR COTTER, WIRE X X X X X X

3 RF FLT9902 DRYER, 1/4 X .042 FILTER X X X X X X

4 RF FLT9902 WASHER, 5/16 FLAT X X X X X X

5 RF WRP1705 HEAT EXCHANGE - - - X X X

5 RF WRP1706 HEAT EXCHANGE - - X - - -

5 RF WRP1707 HEAT EXCHANGE (8-2017) - - - X X X

6 RP SHD1709 SHROUD, CONDENSOR X - X - - -

6 RP SHD1710 SHROUD, CONDENSOR - - - X X X

7 RF COI1604 COIL, CONDENSER X X X X X X

8 RP DIV1701 DIVIDER, AIR X - X X X X

8 RP DIV1702 DIVIDER, AIR (08-2017) - X - X X X

9 RF FAN1401 FAN X X X - - -

9 RF FAN1701 FAN - - - X X X

10 RF FAN0703 GUARD, FAN X X X X X X

11 PB ELB1002 ELBOW, BARB NYLON 1/2" X X X X X X

*

RP 4044002-290

REFRIGERATION PACKAGE, REPLACEMENT - - X - - -

*

RP 4044002-290A

REFRIGERATION PACKAGE, REPLACEMENT (08-2017)

- - - X X X

*

RP 4044000-290

REFRIGERATION PACKAGE, REPLACEMENT X X - - - -

OM-WORK TOP/UNDERCOUNTER SERIES 15

Parts List

ITEM PART # DESCRIPTION 9404-290 9404-32-290 9404F-290 9404F-32-290 9802F-290 9302F-290

1 RF FAN0703 GUARD, FAN X X X X X X

2 RP SHD1707 SHROUD, EVAPORATOR - - - X X X

2 RP SHD1708 SHROUD, EVAPORATOR X X X - - -

3 RF COI120B COIL, EVAPORATOR X X X X X X

4

EL WIR461-90

POWER CORD, 9’ X X X X X X

5 EL GRM300 GROMMET, 7/8” X X X X X X

6 RP CNT1706 CONTROL, DANFOSS, PREPROGRAMMED, 9404F-290 - - X - - -

6A RP CNT1710 CONTROL, DANFOSS, PREPROGRAMMED,

9800F,9300F,9404F-32-290

- - - X X X

6B

RP CNT17013

CONTROL, DANFOSS, PREPROGRAMMED, 9404-290 REF

X X - - - -

7 RF TRM0501 THERMODISC, 2 WIRE - - X X X X

8 RF FAN1401 FAN X X X - - -

8 RF FAN1701 FAN - - - X X X

9 EL WIR1401 COIL, HEATER DEFROST - - X X X X

16 OM-WORK TOP/UNDERCOUNTER SERIES

Parts List

ITEM PART # DESCRIPTION 9404-290 9404-32-290 9404F-290 9404F-32-290 9802F-290 9302F-290

1 RP DOR101 DOOR - RIGHT - 18" - - - - X -

1 RP DOR103 DOOR - RIGHT - 24" - - - - - X

1

RP DOR102

DOOR - LEFT - 18" - - - - X -

1 RP DOR104 DOOR - LEFT - 24" - - - - - X

1 RP DOR105 DOOR - RIGHT - 27" X - X - - -

1 RP DOR106 DOOR - LEFT - 27" X - X - - -

1 RP DOR107 DOOR - RIGHT - 32" - X - X - -

1 RP DOR108 DOOR - LEFT - 32" - X - X - -

2 RP TOP9404 TOP ASSY - REPLACEMENT - - X - - -

2 RP TOP9302 TOP ASSY - REPLACEMENT - - - - X -

2 RP TOP9802NS TOP ASSY - REPLACEMENT - - - - - X

3 HD CST060 CASTER X - X - X X

3 HD CST061 CASTER X - X - X X

3 HD CST025 CASTER - X - X - -

4 RP CPN1703 PAN, CONDENSATE - - - - X X

4 RP CPN1705 PAN, CONDENSATE X - X - - -

4 RP CPN1707 PAN, CONDENSATE (08-2017) - - - - X X

4 RP CPN1708 PAN, CONDENSATE (08-2017) - X - X - -

5 RP BRK1704 BRACKET, CONDENSATE PAN - - - - X X

5

RP BRK1705

BRACKET, CONDENSATE PAN - X - X - -

5

RP BRK1706

BRACKET, CONDENSATE PAN

X - X - - -

5

RP BRK1708

BRACKET, CONDENSATE PAN (08-2017) - - - - X X

6

FA SCW0904

THUMBSCREW - - X - - -

7

RP LVR9412

LOUVER, PANEL - X - X - -

8

RP WCK1701

WICKING, CONDENSATE PAN (08-2017) - - - X X X

*

HD SHL020

SHELF, WIRE - - - - X -

*

HD SHL030

SHELF, WIRE X - X - - -

*

HD SHL035

SHELF, WIRE - - - - X -

*

HD SHL040

SHELF, WIRE - - - - - X

*

HD SHL040A

SHELF, WIRE - - - - - X

*

HD SHL066

SHELF, WIRE - X - X - -

OM-WORK TOP/UNDERCOUNTER SERIES 17

Parts List

ITEM PART # DESCRIPTION 9404-290 9404-32-290 9404F-290 9404F-32-290 9802F-290 9302F-290

1 RP BCK1704 BACK PANEL, SS X - X - - -

1 RP BCK1705 BACK PANEL, SS - X - X - -

1 RP BCK1706 BACK PANEL, SS - - - - - X

1 RP BCK1707 BACK PANEL, SS - - - - X -

2

EL GRM1201

GROMMET, 3" BLACK X X X X X X

18 OM-WORK TOP/UNDERCOUNTER SERIES

Electrical Schematic

OM-WORK TOP/UNDERCOUNTER SERIES 19

Electrical Schematic

20 OM-WORK TOP/UNDERCOUNTER SERIES

Electrical Schematic

La page charge ...

Randell 9000-290/9000F-290 Manuel utilisateur

Randell 9000-290/9000F-290 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents