Randell FX Series Manuel utilisateur

This manual provides information on installation, operating,

maintenance, trouble shooting & replacement parts for:

OPERATOR MANUAL

IMPORTANT INFORMATION, KEEP FOR OPERATOR

PART NUMBER PP MNL1701, REV E (08/17)

FX SERIES:

• 2N1-Two Cooling Systems in one:

- Refrigerator (40ºF)

- Freezer (-5º to 0ºF)

- Or anywhere in between (-5º to 40ºF)

Information contained in this document is known to be current and accurate at the time

of printing/creation. Unified Brands recommends referencing our product line websites,

unifiedbrands.net, for the most updated product information and specifications.

1055 Mendell Davis Drive

Jackson, MS 39272

888-994-7636, fax 888-864-7636

unifiedbrands.net

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.

READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND

WARNINGS CONTAINED IN THIS MANUAL.

WARNING / FOR YOUR SAFETY

Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this or any other appliance.

WARNING

R290 flammable refrigerant in use. Improper installation,

adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read the installation,

operating and maintenance instructions thoroughly before

installing or servicing this equipment.

NOTIFY CARRIER OF DAMAGE AT ONCE

It is the responsibility of the consignee to inspect the container upon receipt of

same and to determine the possibility of any damage, including concealed dam-

age. Unified Brands suggests that if you are suspicious of damage to make a

notation on the delivery receipt. It will be the responsibility of the consignee to file

a claim with the carrier. We recommend that you do so at once.

Manufacture Service/Questions 888-994-7636.

FX-2WS-290

FX-2WSA-290

FX-2WSRE-290

FX-2WSREA-290

FX-2UCB-290

FX-3SS-290

FX-1CS-290

FX-1CS-60-290

FX-2SC-290

FX-1CS-52-290

FX-1CSRE-290

FX-2CSRE-290

FX-1-290

FX-1A-290

FX-1UC-290

FX-1RE-290

FX-1REA-290

2 OM-FX SERIES

Important Operator Notices ......................................................... page 3

Labeling ...................................................................................... page 4-5

Equipment Description .................................................................. page 6

Installation .................................................................................... page 7

Operation ................................................................................ page 8-9

Maintenance ................................................................................ page 10

Troubleshooting ........................................................................... page 11

Service ........................................................................................ page 12

Parts List ................................................................................ page 13-16

Electrical Schematic ................................................................... page 17

Service Log ................................................................................. page 18

Warranty Policies ................................................................... page 19-21

Table of Contents

OM-FX SERIES 3

IMPORTANT - READ FIRST - IMPORTANT

Congratulations on your recent purchase of Unified Brands food service equipment, and welcome to the growing family of satisfied

Unified Brands customers.

Our reputation for superior products is the result of consistent quality craftsmanship. From the earliest stages of product design to

successive steps in fabrication and assembly, rigid standards of excellence are maintained by out staff of designers, engineers, and

skilled employees.

Only the finest heavy-duty materials and parts are used in the production of Unified Brands brand equipment. This means that each

unit, given proper maintenance will provide years of trouble free service to its owner.

In addition, all Unified Brands food service equipment is backed by some of the best warranties in the food service industry and by

our professional staff of service technicians.

Retain this manual for future reference.

NOTICE: DUE TO A CONTINUOUS PROGRAM OF PRODUCT IMPROVEMENT, UNIFIED BRANDS RESERVES THE RIGHT TO MAKE CHANGES IN

DESIGN AND SPECIFICATIONS WITHOUT PRIOR NOTICE.

NOTICE: PLEASE READ THE ENTIRE MANUAL CAREFULLY BEFORE INSTALLATION. IF CERTAIN RECOMMENDED PROCEDURES ARE NOT

FOLLOWED, WARRANTY CLAIMS WILL BE DENIED.

MODEL NUMBER _________________________

SERIAL NUMBER _________________________

INSTALLATION DATE ______________________

THE SERIAL NUMBER IS LOCATED IN THE CABINET LEFT SIDE UNDER THE DRAWER TRACK. AN EXAMPLE IS SHOWN BELOW.

4 OM-FX SERIES

The following warning labels will be found on your equipment:

INTERIOR EVAPORATOR COVER

NEAR MACHINE COMPARTMENT AND NAMEPLATE

Labeling

OM-FX SERIES 5

EXTERIOR OF UNIT

NEAR EXPOSED REFRIGERANT TUBING

Labeling

6 OM-FX SERIES

Equipment Description

FX-2WS-290

MODEL

LENGTH

DEPTH

HEIGHT

NO. OF DRAWERS

STORAGE

(CUBIC FEET)

REFRIG. POWER

USAGE (PER DAY)

FREEZER POWER

USAGE (PER DAY)

COMPRESSOR

VOLT

AMPS

NEMA

SHIP WT (LBS)

FX-1-290

43.3” 28”

36” 1 3.1 0.88 1.65 1/4(1) 115/60/1 1.7 5-15P(1)

225

FX-1A-290

43.3” 28”

14.7” 1 2.5 0.79 1.7 1/4(1) 115/60/1 1.7 5-15P(1)

245

FX-1UC-290

27” 29.5”

33.2” 1 2.83 0.75 1.83 1/4(1) 115/60/1 1.7 5-15P(1)

422

FX-1RE-290

35” 34.5”

16.3” 1 3.1 0.88 1.65 1/4(1) 115/60/1 1.7 5-15P(1)

245

FX-1REA-290

35” 34.5”

14.7” 1 2.5 0.79 1.7 1/4(1) 115/60/1 1.7 5-15P(1)

245

FX-2WS-290

43.3” 28”

36.2” 2 6.2 1.76 3.3 1/4(2) 115/60/1 3.4 5-15P(2)

635

FX-2WSA-290

43.3” 28”

36.2” 2 5 1.58 3.4 1/4(2) 115/60/1 3.4 5-15P(2)

635

FX-2WSRE-290

35” 34.5”

36.2” 2 6.2 1.76 3.3 1/4(2) 115/60/1 3.4 5-15P(2)

635

FX-2WSREA-290

35” 34.5”

33” 2 5 1.58 3.4 1/4(2) 115/60/1 3.4 5-15P(2)

635

FX-2UCB-290

54” 29.5”

43.5” 2 6.2 1.5 3.66 1/4(2) 115/60/1 3.4 5-15P(2)

900

FX-3SS-290

43.3” 28”

51.2” 3 9.3 2.64 4.95 1/4(3) 115/60/1 5 5-15P(3)

891

FX-1CS-290 48” 33” 23.3” 1 3 0.88 1.65 1/4(1) 115/60/1 1.7 5-15P(1) 385

FX-1CS-52-290 52” 33” 23.3” 1 3 0.88 1.65 1/4(1) 115/60/1 1.7 5-15P(1) 430

FX-1CS-60-290 60” 33” 23.3” 1 3 0.88 1.65 1/4(1) 115/60/1 1.7 5-15P(1) 470

FX-2CS-290 96” 33” 23.3” 2 6 1.76 3.3 1/4(2) 115/60/1 1.7 5-15P(2) 836

FX-1CSRE-290 38.65” 35.58” 23.2” 1 3 0.88 1.65 1/4(1) 115/60/1 1.7 5-15P(1) 407

FX-2CSRE-290 76” 35.58” 23.2” 2 6 1.76 3.3 1/4(2) 115/60/1 1.7 5-15P(2) 770

FX-1CS-290

OM-FX SERIES 7

Installation

SELECTING A LOCATION FOR YOUR NEW UNIT

The following conditions should be considered when selecting a location for your unit:

1. Floor and Countertop Load: The area on which the unit will rest must be level, free

of vibration, and suitably strong enough to support the combined weights of the unit

plus the maximum product load weight.

2. Clearance: Clearance must be a combined total of at least 1” on back of unit for FX-

1RE(A)-290. Do not place any object that can block the ventilation exhaust from the

machine compartment register. Area of equipment must be free of all combustible

materials.

3. Ventilation: The air cooled self contained unit requires a sufficient amount of cool

clean air. Avoid surrounding your FX unit around other heat generating equipment

and out of direct sunlight. Also, avoid locating in an unheated room or where the

room temperature may drop below 70° F or rise above 100° F.

INSTALLATION CHECKLIST

After the final location has been determined, refer to the following checklist prior to

start-up:

1. Check all exposed refrigeration lines to ensure that they are not kinked, dented, or

rubbing together.

2. Check that the condenser and evaporator fans rotate freely without striking any

stationary members.

3. Unit must be properly leveled; check all legs or casters to ensure they all are in

contact with the floor while maintaining a level work surface. Adjusting bullet

feet heights or shimming casters may be necessary if the floor is not level. NOTE:

Damage to equipment may result if not followed. Unified Brands is not responsible

for damage to equipment if improperly installed.

4. Allow unit time to cool down to temperature. If temperature adjustments are required,

the control is located on the front panel. Confirm that the unit is holding the desired

temperature.

5. Refer to the front of this manual for serial number location. Please record this

information in your manual on page 3 now. It will be necessary when ordering

replacement parts or requesting warranty service.

6. Before putting in food, allow your unit to operate for approximately two (2) hours so

that interior of the unit is cooled down to storage temperature.

7. Check drawer to ensure the drawer slides freely and fully extends along with seating

into the cabinet properly when closed.

ELECTRICAL SUPPLY

Any wiring should be done by a qualified electrician in accordance with all national and

local electrical codes. A properly wired and grounded outlet will assure proper operation.

Please consult the data tag attached to the compressor to ascertain the correct electrical

requirements. Supply voltage and amperage requirements are located on the serial

number tag (see page 3 for location).

CAUTION!

THIS UNIT CONTAINS R290 FLAMMABLE

REFRIGERANT. USE CAUTION WHEN

HANDLING MOVING AND USE OF THE

REFRIGERATOR OR FREEZER. AVOID

DAMAGING THE REFRIGERANT TUBING OR

INCREASE THE RISK OF A LEAK.

FAILURE TO FOLLOW INSTALLATION

GUIDELINES AND RECOMMENDATIONS MAY

VOID THE WARRANTY ON YOUR UNIT.

IT IS IMPORTANT THAT YOUR UNIT HAS

ITS OWN DEDICATED LINE. CONDENSING

UNITS ARE DESIGNED TO OPERATE WITH

A VOLTAGE FLUCTUATION OF PLUS OR

MINUS 10% OF THE VOLTAGE INDICATED

ON THE UNIT DATA TAG. BURN OUT OF A

CONDENSING UNIT DUE TO EXCEEDING

VOLTAGE LIMITS WILL VOID THE WARRANTY.

THE DANFOSS CONTROLLER HAS LOW

VOLTAGE PROTECTION AND WILL NOT

OUTPUT VOLTAGE TO THE COMPRESSOR IF

VOLTAGE IS LESS THAN 104V.

THIS UNIT IS INTENDED FOR USE IN

LABORATORIES IN COMMERCIAL,

INDUSTRIAL, OR INSTITUTIONAL

OCCUPANCIES AS DEFINED IN THE SAFETY

STANDARD FOR REFRIGERATION SYSTEMS,

ASHRAE 15.

8 OM-FX SERIES

Operation

THE FX-1 SERIES UNIT IS DESIGNED TO

OPERATE IN EITHER REFRIGERATOR OR

FREEZER. FACTORY DEFAULT SETTING IS

FOR FREEZER MODE AND SET AT -3ºF.

Allow unit to operate for approximately two (2) hours before placing in food.

AMBIENT CONDITIONS

Unit is designed for normal operating temperatures are between 70-100°F. Operating

outside of those temperatures may cause premature product wear or failure

Unified Brands has attempted to preset the temperature control to ensure that your

unit runs at an optimum temperature, but due to varying ambient conditions, including

elevation, food type and your type of operation, you may need to alter this temperature

using control adjustment until desired temperature is reached.

DANFOSS CONTROLLER OPERATION

LED FUNCTION

Compressor energized & Evaporator fan de-energized

Defrost in progress

Fans delay after defrost completion

Evaporator fan energize

An alarm is occurring

ºC / ºF Temperature unit

POWER ON / OFF: Press and hold the power button until LED display turns On / Off

MANUAL DEFROST: Press and hold “Defrost” Button

CHANGE SET POINT: To raise temperature

1. Press and hold “

” to access set point.

2. When set point start flashing, Press “

” to adjust set point

3. After 30 seconds, the display automatically reverts to showing the current

temperature

CHANGE SET POINT: To lower temperature

1. Press and hold “v” to access set point

2. When set point start flashing, Press “v” to adjust set point

3. After 30 seconds, the display automatically reverts to showing the current

temperature

POWER ON / OFF

MANUAL DEFROST

CHANGE SET POINT

OM-FX SERIES 9

Operation

CHANGE FROM ºF /ºC :

1. Press the up/down buttons simultaneously for 5 seconds to access the menu.

2. Password is requested. Password is 000.

3. Press the bottom left button to OK the password.

4. Using the up/down buttons, navigate to the “diS” level. Press the bottom left button

to OK the selection.

5. Using the up/down buttons, navigate to the “CFu” level. Press the bottom left button

to OK the selection.

a. “-F” designates Fahrenheit.

b. “-C” designates Celsius.

6. Press the top left button repeatedly to return to exit and return to the home screen.

DRAWER / DOOR ALARM: Acknowledging Alarms – Visual Display Only

1. After 2 minutes the display will flash the alarm message “dor”

2. Press any button to acknowledge alarm

DRAWER / DOOR ALARM: Door Alarm Activation – If audible alarm is wanted

1. Press the up/down buttons simultaneously for 5 seconds to access the menu.

2. Password is requested. Password is 000.

3. Press the bottom left button to OK the password.

4. Using the up/down buttons, navigate to the “ALA” level. Press the bottom left button

to OK the selection.

5. Using the up/down buttons, navigate to the “Abd” level. Press the bottom left button

to OK the selection.

a. “0” Disables the alarm.

b. Any other number is the number of minutes before the buzzer sounds after the

drawer is opened.

6. Press the top left button repeatedly to return to exit and return to the home screen.

10 OM-FX SERIES

Maintenance

Unified Brands strongly suggests a preventive maintenance program which would include

the following Monthly procedures:

1. Clean fan blades on the condensing unit and evaporator assembly.

2. Clean all gaskets on a weekly if not daily basis with a solution of warm water and a

mild detergent to extend gasket life.

3. Lubricate door hinges with lithium grease. Modify for FX drawer slides and verify with

engineering

RECOMMENDED CLEANERS FOR YOUR STAINLESS STEEL INCLUDE THE FOLLOWING:

JOB CLEANING AGENT COMMENTS

Routine cleaning

Soap, ammonia,

detergent Medallion

Apply with a sponge or cloth

Fingerprints and smears Arcal 20, Lac-O-Nu, Ecoshine Provides a barrier film

Stubborn stains and

discoloration

Cameo, Talc, Zud,

First Impression

Rub in the direction of the

polish lines

Greasy and fatty acids, blood,

burnt-on foods

Easy-Off, Degrease It,

Oven Aid

Excellent removal on all

finishes

Grease and Oil

Any good commercial

detergent

Apply with a sponge or cloth

Restoration/Preservation Benefit, Super Sheen Good idea monthly

Reference: Nickel Development Institute, Diversey Lever, Savin, Ecolab, NAFEM

Proper maintenance of equipment is the ultimate necessity in preventing costly repairs. By

evaluating each unit on a regular schedule, you can often catch and repair minor problems

before they completely disable the unit and become burdensome on your entire operation.

For more information on preventive maintenance, consult your local service

company or CFESA member. Most repair companies offer this service at very reasonable

rates to allow you the time you need to run your business along with the peace of mind

that all your equipment will last throughout its expected life. These services often offer

guarantees as well as the flexibility in scheduling or maintenance for your convenience.

For a complete listing of current Unified Brands ASA please visit www.unifiedbrands.net.

Unified Brands believes strongly in the products it manufactures and backs those products

with one of the best warranties in the industry. We believe with the proper maintenance and

use, you will realize a profitable return on your investment and years of satisfied service.

DO NOT USE SHARP UTENSILS AND/OR

OBJECTS.

CAUTION

DO NOT USE ABRASIVE CLEANING

SOLVENTS, AND NEVER USE HYDROCHLORIC

ACID (MURIATIC ACID) ON STAINLESS STEEL.

DO NOT USE STEEL PADS, WIRE BRUSHES,

SCRAPERS, OR CHLORIDE CLEANERS TO

CLEAN YOUR STAINLESS STEEL.

DO NOT PRESSURE WASH EQUIPMENT AS

DAMAGE TO ELECTRICAL COMPONENTS

MAY RESULT.

OM-FX SERIES 11

Troubleshooting

This unit is designed to operate smoothly and efficiently if properly maintained. However, the following is a list of checks to make in

the event of a problem. Wiring diagrams are found at the end of this manual.

SYMPTOM POSSIBLE CAUSE PROCEDURE

Unit does not run

No power to unit Plug in unit

Control in OFF position Turn controller on

Faulty control Call for service at 888-994-7636

Unit too cold Incorrect set point Adjust control set point

Unit too warm

Door / drawer ajar Ensure door / drawer is fully closed

Gasket torn or out of place Inspect the gasket for wear and position

Incorrect set point Adjust control set point

Warm product introduced to cabinet Pre-chill product 37ºF or 3ºF degree for freezer

Ice on the coil Initiate manual defrost

Unit noisy Ice on the coil Initiate manual defrost

Unit does not defrost Excessive ice on the coil Initiate manual defrost

When in doubt, turn unit off and call for service at 888-994-7636.

12 OM-FX SERIES

Service

This piece of equipment uses a R290 Refrigeration system. This equipment has been

clearly marked on the serial tag the type of refrigerant that is being used. There is also a

warning labels stating that the unit contains R290 refrigerant.

No smoking or open flames when servicing this equipment. If needed, use a CO

2

or

dry=power type fire extinguisher

Only authorized service technician, certified in R290 system should service this equipment.

MANIFOLD SET

A R134A manifold set can be used for servicing this equipment.

REFRIGERANT RECOVERY

Follow all national and local regulations for R-290 refrigerant recovery.

LEAKING CHECKING AND REPAIR

Leak check an R-290 system the same way you would an R-134a or R-404A system with

the following exceptions.

1. Do not use a Halid leak detector on a R290 system.

2. Electronic leak detector must be designated specifically for combustible gas.

Use of a bubble solution or an ultrasonic leak detector are acceptable.

When repairing a leak, it is recommended using oxygen free dry nitrogen with a trace gas

not exceeding 200PSI.

When accessing an R290 system, piercing valves are not to remain on the equipment in

a permanent manner. After charge is recovered, Schrader valves are to be installed on the

process stubs. Proper charge is to be weighed into the system and the system is to be

leak checked afterwards.

The R290 equipment must have red process tubes and other devices through which the

refrigerant is serviced, such as any service port. This color marking must remain on the

equipment. If marking is removed, it must be replace and extend at least 2.5 centimeters

(1”) from the compressor.

CHARGING

Follow the charge amount specified on the data tag. It is recommended to use the shortest

hoses possible to prevent undercharging.

• Ensure the system is sealed and leak checked

• Evacuate system to a minimum 500 micron

• Weigh in correct charge

• Leak check the system again

• Bleed the refrigerant from the high side hose to the low side hose

• Disconnect the hoses

• Remove line taps

CAUTION!

COMPONENT PARTS SHALL BE REPLACED

WITH LIKE COMPONENTS. SERVICE WORK

SHALL BE DONE BY FACTORY AUTHORIZED

SERVICE PERSONNEL, SO AS TO MINIMIZE

THE RISK OF POSSIBLE IGNITION DUE TO

INCORRECT PARTS OR IMPROPER SERVICE.

OM-FX SERIES 13

Parts List

ITEM PART NUMBER DESCRIPTION

1 RF FAN0601 FAN. AXIAL, 127 X 38MM 120 CFM,115V CONDENSER

2 FA BLT0349 BOLT, 6-32x1/2 T/H/P 18-8 SS 08BC PHILLIPS TRUSS SS

3 FA NUT0312 RIVNUT, 6-32 THD

4 RF CMP1604 COMPRESSOR, 3/8 HP, LO, 404, 115V, DANFOSS

4a RF CMP1604SC COMPRESSOR START COMPONENTS

5 RF FLT9902 DRYER, 1/4x.042 FILTER EKP-032 SC DBL INL CAP TUBE N

6 RP WRP1701 CAP TUBE HEAT EXCHANGER ASSY

7 RF COI1606 COIL, 3.46" X 9.00" X 5.90"CONDENSER

7A RF COI1608 COIL, 3.46" X 9.00" X 5.90"CONDENSER (FX-1RE(A) - 290)

14 OM-FX SERIES

Parts List

ITEM PART NUMBER DESCRIPTION

1 HD CST9801 2.5" SWIVEL CASTER (NO LOCK)--HD CST9801

1A HD CST200 2.5” SWIVEL CASTER (NO LOCK)--HD CST200

2 HD CST9802 2.5" SWIVEL CASTER (WITH LOCK)--HD CST9802

2A HD CST201 2.5” SWIVEL CASTER (WITH LOCK)--HD CST201

3 RP PNL1702 PANEL BACK MACHINE COMP

4 RP END1701 SIDE, EXTERIOR, S/S, RIGHT

5 RP END1702 SIDE, EXTERIOR, S/S, LEFT

6 RP BCK1701 BACK, EXTERIOR

7 HD TRK1101_BASE TRACK, DWR SLIDE L/H 2-1/8 X 28 BAYONET MNT

8 HD TRK1102_BASE TRACK, DWR SLIDE R/H 2-1/8 X 26 (650MM) BAYONET MNT

9 RP CPN0601 PAN CONDENSATE DRAIN

10 EL SWT1604 SWITCH, MAGNETIC

11 RP PNL1701 PANEL ACCESS BACK

12 RP CLP1701 CLIP COUNTER WEIGHT BOTTOM

13 RP LVR1702 LOUVER, S/S, FX-1

13A RP LVR0907 LOUVER, FX-1UC

14 RP TOP1501 TOP, 1100MM X 712MM

14A FOR CHEF STAND TOPS CONSULT FACTORY

15 EL WIR461-90 POWER CORD, 9' 16/3-9O

16 HD WCK1401 CF-SE2001 CONDENSATE 7.00IN X3.00IN X 1/16 IN

OM-FX SERIES 15

Parts List

ITEM PART NUMBER DESCRIPTION

1 RP PAN0705 INSULATED DRAWER TUB FOR FX-1, FX-1RE

1A RP PAN0706 INSULATED DRAWER TUB FOR FX-1A, FX-REA

1B RP PAN0801 INSULATED DRAWER TUB FOR FX-1UC

2 RP GSK0604 GASKET, MAGNETIC, SLIDE SEAL, PF, 765 X 614mm

3 RP DWR1603 DRAWER CARRAIGE ASSY W/FRONT, FX-1, FX-1RE

3A RP DWR1504 DRAWER CARRIAGE ASSY W/FRONT, FX-1UC

4 RP PNL1703 PANEL, FRONT, S/S, FX-1

5 RP FRT1701 FRONT, DRAWER, S/S, FX-1, FX-1RE

5A RP FRT1601 FRONT, DRAWER FX-1UC

6 HD HDL130 CHROME SCULPTURED HANDLE

16 OM-FX SERIES

Parts List

ITEM PART NUMBER DESCRITPION

1 RP DRP0602 EVAPORATOR DRAINING DRAIN PAN W/DEFROST ELEMENT

2 PB ELB0313 ELBOW, 1/2" ID X 3/8" ID 90 CU CXC

3 EL PAD1101 PAD, FLEXIBLE HEATING FOIL 6.9" X 15.75" 150W 120V

4 RF COI0603 COIL, 1.00" X 7.00" X 15.7" STAGED FIN EVAPORATOR

5 RP BRK0704 BRACKET FOR HI-LIMIT

6 RF TRM0501 THERMODISC 2-WIRE, OPEN:70 CLOSE:50 SEO-70-T17

7 RP GSK0604 GASKET, MAGNETIC, SLIDE SEAL, PF, 765 X 614mm

8 RF DIF0601 DIFFUSER, LID FOR FX-1, FX-1A, FX-1RE, FX-1REA

8A RF DIF0801 DIFFUSER, LID FOR FX-1UC

9 RF FAN0602 FAN. AXIAL, 40 X 20MM 10.8 CFM,12VDC EVAPORATOR

10 HD HSE0601 HOSE, .375" ID X 1/2" OD POLYETHYLENE FLEXIBLE TUBE

11 PB ELB0701 ELBOW, BARB NYLON 3/8 X 3/8

12 EL CLM550 CLAMP, 1/2" CABLE CLAMP 3308 N*

13 RF CNT1602 THERMISTER, QT COIL SENSOR, BLUE 10'

14 RF CNT1603 THERMISTER, QTI AIR SENSOR, BLACK 10'

OM-FX SERIES 17

Electrical Schematic

18 OM-FX SERIES

Service Log

Model No: Purchased From:

Serial No: Location:

Date Purchased: Date Installed:

Purchase Order No: For Service Call:

Date Maintenance Performed Performed By

OM-FX SERIES 19

Congratulations on your purchase of a Unified Brands Brand piece of equipment. Unified Brands believes strongly in the products it

builds and backs them with the best warranty in the industry. Standard with every unit is the peace of mind that this unit has been

thoroughly engineered, properly tested and manufactured to excruciating tolerances, by a manufacturer with over 30 years of industry

presence. On top of that front end commitment, Unified Brands has a dedicated staff of certified technicians that monitor our own

technical service hotline at 1-888-994-7636 to assist you with any questions or concerns that may arise after delivery of your new

Unified Brands equipment.

PARTS WARRANTY

1. One year parts replacement of any and all parts that are found defective in material or workmanship. Unified Brands warrants all

component parts of manufactured new equipment to be free of defects in material or workmanship, and that the equipment meets

or exceeds reasonable industry standards of performance for a period of one year from the date of shipment from any Unified

Brands factory, assembly plant or warehouse facility.

NOTE: warranties are effective from date of shipment, with a thirty day window to allow for shipment, installation and set-up. In

the event equipment was shipped to a site other than the final installation site, Unified Brands will warranty for a period of three

months following installation, with proof of starting date, up to a maximum of fifteen months from the date of purchase.

2. Free ground freight of customer specified location for all in warranty parts within continental U.S. Component part warranty does

not cover glass breakage or gasket replacement. Unified Brands covers all shipping cost related to component part warranty sent

at regular ground rates (UPS, USPS). Freight or postage incurred for any express or specialty methods of shipping are the

responsibility of the customer.

LABOR COVERAGE

In the unlikely event a Unified Brands manufactured unit fails due to defects in materials or workmanship within the first ninety days,

Unified Brands agrees to pay the contracted labor rate performed by an Authorized Service Agent (ASA). Any work performed by a

non-ASA will not be honored by Unified Brands. Please consult Unified Brands Technical Support (888-994-7636) for a complete listing

of ASAs or visit the service page of our website: www.unifiedbrands.net. Warranties are effective from date of shipment, with a thirty

day window to allow for shipment, installation and setup. Where equipment is shipped to any site other than final installation, Unified

Brands will honor the labor warranty for a period of ninety days following installation with proof of starting date, up to a maximum of

six months from date of purchase.

Temperature adjustments are not covered under warranty, due to the wide range of ambient conditions.

To request a warranty approval number, call our Field Service Department at: 1-888-994-7636

WHEN OPTIONAL 5 YEAR COMPRESSOR WARRANTY APPLIES

1. Provide reimbursement to an ASA for the cost of locally obtained replacement compressor in exchange for the return of the defective

compressor sent back freight prepaid. NOTE: Unified Brands does limit amount of reimbursement allowed and does require bill

from local supply house where compressor was obtained (customer should not pay servicing agent up front for compressor).

2. Provide repair at the manufacturing facility by requiring that the defective unit be sent back to Unified Brands freight prepaid.

Perform repair at the expense of Unified Brands and ship the item back to the customer freight collect.

3. Furnish a replacement compressor freight collect in exchange for the return of the defective compressor sent back freight prepaid.

4. Furnish complete condensing unit freight collect in exchange for the return of the defective condensing unit sent back freight

prepaid. (Decisions on whether or not to send complete condensing units will be made by Unified Brands in-house service

technician).

Warranty Policies

20 OM-FX SERIES

Warranty Policies

WHEN OPTIONAL LABOR EXTENSION POLICY APPLIES

Unified Brands will provide reimbursement of labor to an ASA for any customer that has an optional labor extension of our standard

warranty. (Contracted rates do apply) Unified Brands offers both 1 and 2 year extensions. Labor extensions begin at the end of our

standard warranty and extend out 9 months to 1 calendar year or 21 months to 2 calendar years from date of purchase. Please contact

Unified Brands technical service hotline at 1-888-994-7636 for details and any question on Authorized Service Agents (ASA).

WHEN EXPORT WARRANTIES APPLY

1. Unified Brands covers all non-electrical components under the same guidelines as our standard domestic policy.

2. All electrical components operated on 60Hz are covered under our standard domestic policy.

3. All electrical components operated on 50Hz are covered for 90 days from shipment only.

4. Service labor is covered for the first ninety days with authorization from the factory prior to service being performed.

5. Inbound costs on factory supplied items to be responsibility of the customer.

6. Extended warranty options are not available for parts, labor, or compressors from the factory.

ITEMS NOT COVERED UNDER WARRANTY

1. Maintenance type of repairs such as condenser cleaning, temperature adjustments, clogged drains, unit leveling and re-application

of silicone.

2. Unified Brands does not cover gaskets under warranty. Gaskets are a maintenance type component that are subject to daily wear and

tear and are the responsibility of the owner of the equipment. Because of the unlimited number of customer related circumstances

that can cause gasket failure all gasket replacement issues are considered non-warranty. Unified Brands recommends thorough

cleaning of gaskets on a weekly basis with a mild dish soap and warm water. With proper care Unified Brands gaskets can last up

to two years, at which time we recommend replacement of all gaskets on the equipment for the best possible performance.

NOTICE: FOOD LOSS IS NOT COVERED UNDER WARRANTY

3. Repairs caused by abuse such as broken glass, freight damage, or scratches and dents.

4. Electrical component failure due to water damage from cleaning procedures.

5. Improper installation of equipment.

6. Repairs performed outside of Unified Brands’ Authorized Service Agent network.

QUOTATIONS

Verbal quotations are provided for customer convenience only and are considered invalid in the absence of a written quotation. Written

quotations from Unified Brands are valid for 30 days from quote date unless otherwise specified. Unified Brands assumes no liability

for dealer quotations to end-users.

SPECIFICATION & PRODUCT DESIGN

Due to continued product improvement, specification and product design may change without notice.

La page est en cours de chargement...

Randell FX Series Manuel utilisateur

Randell FX Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents