Alpine CDE-122 Le manuel du propriétaire

Marque: Alpine

Modèle: CDE-122

Catégorie: Lecteurs MP3 / MP4

Taper: Le manuel du propriétaire

Ce manuel convient également à

68-16909Z42-B

• OWNER’S MANUAL

Please read before using this equipment.

• MODE D’EMPLOI

Veuillez lire avant d’utiliser cet appareil.

• MANUAL DE OPERACIÓN

Léalo antes de utilizar este equipo.

ALPINE ELECTRONICS MARKETING, INC.

1-1-8 Nishi Gotanda,

Shinagawa-ku,

Tokyo 141-0031, Japan

Phone 03-5496-8231

ALPINE ELECTRONICS OF AMERICA, INC.

19145 Gramercy Place, Torrance,

California 90501, U.S.A.

Phone 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF CANADA, INC.

777 Supertest Road, Toronto,

Ontario M3J 2M9, Canada

Phone 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.

161-165 Princes Highway, Hallam

Victoria 3803, Australia

Phone 03-8787-1200

ALPINE ELECTRONICS GmbH

Wilhelm-Wagenfeld-Str. 1-3, 80807 München, Germany

Phone 089-32 42 640

ALPINE ELECTRONICS OF U.K. LTD.

Alpine House

Fletchamstead Highway, Coventry CV4 9TW, U.K.

Phone 0870-33 33 763

ALPINE ELECTRONICS FRANCE S.A.R.L.

(RCS PONTOISE B 338 101 280)

98, Rue de la Belle Etoile, Z.I. Paris Nord Il,

B.P. 50016, 95945 Roissy Charles de Gaulle

Cedex, France

Phone 01-48638989

ALPINE ITALIA S.p.A.

Viale C. Colombo 8, 20090 Trezzano

Sul Naviglio (MI), Italy

Phone 02-484781

ALPINE ELECTRONICS DE ESPAÑA, S.A.

Portal de Gamarra 36, Pabellón, 32

01013 Vitoria (Alava)-APDO 133, Spain

Phone 945-283588

ALPINE ELECTRONICS (BENELUX) GmbH

Leuvensesteenweg 510-B6,

1930 Zaventem, Belgium

Phone 02-725-13 15

CD Receiver

CDE-124SXM/CDE-123/CDE-122

3-EN

Contents

ENGLISH

Operating Instructions

WARNING

WARNING....................................................... 6

CAUTION........................................................ 6

PRECAUTIONS ............................................... 6

Getting Started

Accessory List ...............................................................9

Turning Power On and Off.......................................9

Source Selection..........................................................9

Detaching and Attaching the Front Panel .........9

Detaching ..................................................................9

Attaching ...................................................................9

Initial System Start-Up............................................ 10

Adjusting Volume .................................................... 10

Setting the Time....................................................... 10

Radio

Listening to Radio.................................................... 11

Presetting Stations Manually............................... 11

Presetting Stations Automatically...................... 11

Tuning to Preset Stations ...................................... 11

Frequency Search Function.................................. 11

CD/MP3/WMA/AAC

Playback ...................................................................... 12

Repeat Play................................................................. 12

M.I.X. (Random Play) ............................................... 12

Searching for CD Text ............................................. 12

Folder/File Name Search

(concerning MP3/WMA/AAC).............................. 12

Folder Name Search mode............................... 12

File Name Search mode..................................... 13

Quick Search .............................................................. 13

About MP3/WMA/AAC........................................... 13

Terminology........................................................... 14

Sound Setting

Adjusting Subwoofer Level/Bass Level/Mid

Level/Treble Level/Balance (Between Left and

Right)/Fader (Between Front and Rear)/

Loudness/Defeat.......................................................14

Sound Setting ............................................................15

Equalizer Presets (FACTORY EQ)......................15

Adjusting the Parametric Equalizer Curve

(3BAND EQ).............................................................15

Setting the Bass Control ..........................................15

Setting the Mid Control ...........................................15

Setting the Treble Control.......................................16

Adjusting the High Pass Filter ..........................16

Turning Subwoofer ON/OFF.............................16

Adjusting the Low Pass Filter ...........................16

Setting the Subwoofer Phase...........................16

Setting the Subwoofer System........................16

Other Functions

Displaying the Text...................................................17

About the indication display............................17

About “Text” ...........................................................17

Using the Front AUX Input Terminal..................17

Set your favorite source to the FAV button

(FAV SETUP).................................................................18

Set your favorite source .....................................18

Recall your favorite source ...............................18

SETUP

Setting ..........................................................................18

BLUETOOTH Setting (CDE-123 only)..............19

Setting the BLUETOOTH Connection..................19

General Setting .....................................................19

Set your favorite source to the FAV button

(FAV SETUP) ..................................................................19

Playing MP3/WMA/AAC Data (PLAY MODE).....19

Turning Mute Mode On/Off (INT MUTE) ............19

Setting the AUX REAR Setup Mode

(AUX-R SET) (CDE-123 only)....................................19

Setting the AUX SETUP Mode................................20

Setting the AUX Level (AUX GAIN) .......................20

Setting the AUX REAR Level (AUX-R GAIN)

(CDE-123 only).............................................................20

Connecting to an External Amplifier

(POWER IC)....................................................................20

Demonstration ............................................................20

Display Setting ......................................................21

Dimmer Control ..........................................................21

Scroll Type Setting .....................................................21

Scroll Setting (TEXT SCR) .........................................21

4-EN

Contents

ENGLISH

SiriusXM (SXM) Satellite Radio Setting

(CDE-124SXM/CDE-123 only) (Only when

a SiriusXM Tuner is connected and the

current source is Satellite Radio

(SIRIUSXM))............................................................. 21

Managing Artist and Song Alerts .........................21

Setting the Favorite Sports Team Alerts ............21

Setting the Parental Control...................................22

Confirming the strength of the SiriusXM

signal...............................................................................22

iPod/iPhone and USB Setting ......................... 22

Setting the USB Search Mode................................22

Setting the USB Skip function ...............................22

Setting the Pandora Source....................................22

Setting the Pandora Volume..................................22

Flash Memory/Portable audio player

(optional)

Connecting the Flash Memory (optional)....... 23

When connect Flash Memory to Front USB

Connection Terminal .......................................... 23

Remove Flash Memory from Front USB

Connection Terminal .......................................... 23

Using the Flash Memory/Portable audio

player Banking Function ....................................... 23

Playback ...................................................................... 24

Searching for a desired Song............................... 24

Searching by Tag information ......................... 24

Searching by artist name.........................................24

Searching by Explorer (FILE NAME) mode

(Flash Memory only) ........................................... 25

Repeat Play................................................................. 25

M.I.X. (Random Play) ............................................... 25

Select Playlist/Artist/Album/Genre/

Composer/Folder ..................................................... 26

Alphabet Skip Function

(Tag search mode only) ......................................... 26

Quick Search ............................................................. 26

Search Position Memory ....................................... 26

iPod/iPhone (optional)

Connecting an iPod/iPhone..................................26

Setting the iPod Control ........................................27

Playback .......................................................................27

Searching for a desired Song ...............................27

Direct Search Function ...........................................28

Select Playlist/Artist/Album/Genre/

Composer/Episode ..................................................28

Alphabet Skip Function..........................................28

Search Position Memory ........................................28

Random Play Shuffle (M.I.X.).................................28

Repeat Play .................................................................29

Displaying the Text...................................................29

Pandora Radio (iPhone) (Optional)

Listening to Pandora ...............................................29

“Thumbs” Feedback.................................................30

Searching for a Desired Station ...........................30

QuickMix ......................................................................30

Bookmarking a Desired Song or Artist .............30

Creating a New Station...........................................30

Search Position Memory ........................................31

Changing the Display..............................................31

SiriusXM Satellite Radio Operation

(CDE-124SXM, supplied; CDE-123,

optional)

Receiving Channels with the SiriusXM Tuner

(CDE-124SXM, supplied; CDE-123,

optional).......................................................................31

Checking the SiriusXM Radio ID Number ........32

Storing Channel Presets .........................................32

Tuning Channels using Presets............................32

Category Browsing...................................................32

Storing the desired Artist/Song...........................32

Receiving and Tuning to an Alert .......................33

Search Function ........................................................33

Using Jump Memory and Jump Recall

function........................................................................33

Instant Replay Function..........................................33

Using iTunes tagging ..............................................33

Changing the Display..............................................34

5-EN

Contents

ENGLISH

Information

In Case of Difficulty.................................................. 34

Basic.......................................................................... 34

Radio......................................................................... 34

CD .............................................................................. 34

MP3/WMA/AAC .................................................... 35

Audio........................................................................ 35

iPod ........................................................................... 35

Indication for CD Player..................................... 35

Indication for Flash Memory/Portable audio

player........................................................................ 35

Indication for iPod Mode................................... 36

Indication for Pandora Radio Mode .............. 36

SiriusXM Advisory Messages

(CDE-124SXM/CDE-123 only) .......................... 36

Specifications ............................................................ 38

Installation and Connections

WARNING..................................................... 39

CAUTION......................................................39

PRECAUTIONS ............................................. 39

Installation.................................................................. 40

Removal................................................................... 40

iPod/iPhone Connection

(sold separately) ................................................... 41

When connect to Front USB Connection

Terminal.........................................................................41

When connect to Rear USB Connector

(CDE-123 only).............................................................41

Remove the iPod/iPhone.........................................41

Rear Flash Memory Connection

(CDE-123 only) (sold separately) .................... 41

Connect Flash Memory............................................41

Remove Flash Memory.............................................41

Connections............................................................... 42

LIMITED WARRANTY

6-EN

Operating Instructions

WARNING

This symbol means important instructions. Failure

to heed them can result in serious injury or death.

DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY

FROM SAFELY DRIVING YOUR VEHICLE.

Any function that requires your prolonged attention should only be

performed after coming to a complete stop. Always stop the vehicle

in a safe location before performing these functions. Failure to do so

may result in an accident.

KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE

NOISES WHILE DRIVING.

Excessive volume levels that obscure sounds such as emergency

vehicle sirens or road warning signals (train crossings, etc.) can be

dangerous and may result in an accident. LISTENING AT LOUD

VOLUME LEVELS IN A CAR MAY ALSO CAUSE HEARING

DAMAGE.

DO NOT DISASSEMBLE OR ALTER.

Doing so may result in an accident, fire or electric shock.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may

result in fire, etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF

CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult

a physician immediately.

USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.

Failure to do so may result in fire or electric shock.

DO NOT BLOCK VENTS OR RADIATOR PANELS.

Doing so may cause heat to build up inside and may result in fire.

USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.

Use for other than its designed application may result in fire,

electric shock or other injury.

DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION

SLOTS OR GAPS.

Doing so may result in personal injury or damage to the product.

CAUTION

This symbol means important instructions. Failure

to heed them can result in injury or material

property damage.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS.

Failure to do so may cause personal injury or damage to the

product. Return it to your authorized Alpine dealer or the nearest

Alpine Service Center for repairing.

PRECAUTIONS

Product Cleaning

Use a soft dry cloth for periodic cleaning of the product. For more

severe stains, please dampen the cloth with water only. Anything

else has the chance of dissolving the paint or damaging the plastic.

Temperature

Be sure the temperature inside the vehicle is between +60°C

(+140°F) and −10°C (+14°F) before turning your unit on.

Moisture Condensation

You may notice the CD playback sound wavering due to

condensation. If this happens, remove the disc from the player and

wait about an hour for the moisture to evaporate.

Damaged Disc

Do not attempt to play cracked, warped, or damaged discs. Playing

a bad disc could severely damage the playback mechanism.

Maintenance

If you have problems, do not attempt to repair the unit yourself.

Return it to your Alpine dealer or the nearest Alpine Service Station

for servicing.

Never Attempt the Following

Do not grip or pull out the disc while it is being pulled back into the

player by the automatic reloading mechanism.

Do not attempt to insert a disc into the unit when the unit power is

off.

Inserting Discs

Your player accepts only one disc at a time for playback. Do not

attempt to load more than one disc.

Make sure the label side is facing up when you insert the disc.

“ERROR” will be displayed on your player if you insert a disc

incorrectly. If “ERROR” continues to be displayed even though the

disc has been inserted correctly, push the RESET switch with a

pointed object such as a ballpoint pen.

Playing a disc while driving on a very bumpy road may result in

skips, but this will not scratch the disc or damage the player.

WARNING

7-EN

New Discs

To prevent the CD from jamming, “ERROR” is displayed if discs

with irregular surfaces are inserted or if discs are inserted

incorrectly. When a new disc is ejected immediately after initial

loading, use your finger to feel around the inside of the center hole

and outside edge of the disc. If you feel any small bumps or

irregularities, this could inhibit proper loading of the disc. To

remove the bumps, rub the inside edge of the hole and outside edge

of the disc with a ballpoint pen or other such instrument, then

insert the disc again.

Irregular Shaped Discs

Be sure to use round shape discs only for this unit and never use any

special shape discs.

Use of special shape discs may cause damage to the mechanism.

Installation Location

Make sure this unit will not be installed in a location subjected to:

•Direct sun and heat

• High humidity and water

• Excessive dust

•Excessive vibrations

Correct Handling

Do not drop the disc while handling. Hold the disc so you will not

leave fingerprints on the surface. Do not affix tape, paper, or

gummed labels to the disc. Do not write on the disc.

Disc Cleaning

Fingerprints, dust, or soil on the surface of the disc could cause the

CD player to skip. For routine cleaning, wipe the playing surface

with a clean, soft cloth from the center of the disc to the outer edge.

If the surface is heavily soiled, dampen a clean, soft cloth in a

solution of mild neutral detergent before cleaning the disc.

Disc Accessories

There are various accessories available on the market for protecting

the disc surface and improving sound quality. However, most of

them will influence the thickness and/or diameter of the disc. Using

such accessories can cause the disc to be out of standard

specifications and may create operational problems. We

recommend not using these accessories on discs played in Alpine

CD players.

On handling Compact Discs (CD/CD-R/CD-RW)

• Do not touch the surface.

• Do not expose the disc to direct sunlight.

• Do not affix stickers or labels.

• Clean the disc when it is dusty.

• Make sure that there are no bumps around the disc.

• Do not use commercially available disc accessories.

Do not leave the disc in the car or the unit for a long time. Never

expose the disc to direct sunlight. Heat and humidity may damage

the CD and you may not be able to play it again.

To c ustom ers using C D-R/ CD-RW

• If a CD-R/CD-RW cannot be played back, make sure the last

recording session was closed (finalized).

• Finalize the CD-R/CD-RW if necessary, and attempt playback again.

About media that can be played

The following table shows which discs can be played on which

models.

Use only compact discs with the label side showing the CD logo

marks below.

If you use non-standard compact discs, correct performance cannot

be guaranteed.

You can play CD-Rs (CD-Recordables)/CD-RWs

(CD-ReWritables) which have been recorded only on audio devices.

You can also play CD-Rs/CD-RWs containing MP3 formatted

audio files.

• Some of the following CDs may not play on this unit:

Flawed CDs, CDs with fingerprints, CDs exposed to extreme

temperatures or sunlight (e.g., left in the car or this unit), CDs

recorded under unstable conditions, CDs on which a recording failed

Center Hole

New Disc

Outside

(Bumps)

Bumps

CORRECT

INCORRECT CORRECT

CD CD-TEXT MP3 WMA AAC

CDE-124SXM

/CDE-122



CDE-123 

Transparent Sheet Disc Stabilizer

8-EN

or a re-recording was attempted, copy-protected CDs which do not

conform to the audio CD industry standard.

• Use discs with compressed audio files written in a format compatible

with this unit. For details, refer to “About MP3/WMA/AAC” on

page 13.

• Data files, other than audio, on the disc are ignored and are not

played back.

Protecting the USB Connection Terminal

• Only USB Flash Memory devices, Portable audio player or iPod/

iPhone can be connected to the USB connection terminal on this

unit. Correct performance using other USB products cannot be

guaranteed. A USB hub is not supported.

• Do not connect Flash Memory over 20 mm wide to front USB

terminal.

Also, avoid connecting Flash Memory to the front USB terminal and

connecting Front Aux at the same time.

• If a USB device is inserted in the unit, it projects out and may be a

danger while driving.

Use a commercially available USB extension cable, and connect it in a

safe way.

• Depending on the connected Flash Memory device, the unit may not

function or some functions may not be performed.

• The audio file format that can be played back on the unit is MP3/

WMA/AAC.

• Artist/song name, etc., can be displayed, however characters may not

be correctly displayed.

On Handling USB Flash Memory

CAUTION

Alpine accepts no responsibility for lost data, etc., even if data,

etc., is lost while using this product.

• To prevent malfunction or damage, note the following points.

Read the Flash Memory Owner’s Manual thoroughly.

• Fix the Flash Memory in a location where driver operation will not be

hindered.

• Flash Memory may not function correctly at high or low temperature.

• Use only certified USB Flash Memory Devices. Please pay attention

that even certified Flash Memory, may not function correctly

depending on its type or state.

• Flash Memory function is not guaranteed. Use Flash Memory

according to the terms of agreement.

• Depending on the settings of the Flash Memory type, memory state

or encoding software, the unit may not play back or display properly.

• A file that is copy-protected (copyright protection) cannot be played

back.

• Flash Memory may take time to start playback. If there is a particular

file other than audio in the Flash Memory, it may take considerable

time before the file is played back or searched.

• The unit can play back “mp3”, “wma” or “m4a” file extensions.

• Do not add the above extensions to a file other than audio data. This

non-audio data will not be recognized. The resulting playback may

contain noise that can damage speakers and/or amplifiers.

• It is recommended to back up important data on a personal

computer.

• Do not remove the USB device while playback is in progress. Change

SOURCE to something other than USB, then remove the USB device

to prevent possible damage to its memory.

On Handling Portable audio player

• The unit can control a Portable audio player with the USB interface.

Playable audio file formats are MP3 and WMA.

• Portable audio player function is not guaranteed. Use Portable audio

player according to the terms of agreement. Read the Portable audio

player Owner’s Manual thoroughly.

• Fix the Portable audio player in a location where driver operation will

not be hindered.

• Portable audio player may not function correctly at high or low

temperature.

• Depending on the settings of the Portable audio player type, memory

state or encoding software, the unit may not play back or display

properly.

• If the Portable audio player has an MSC/MTP setting, set to MTP.

• A Portable audio player in which data is stored by USB Mass Storage

may not be playable on the unit.

• Depending on the Portable audio player settings, USB Mass Storage

may be supported. For setting, refer to the Owner’s Manual of the

player.

• The unit can play back MP3/WMA files synchronized by Windows

Media Player (Ver. 7, 8, 9), and are then forwarded to the player. The

“mp3” or “wma” extensions are playable.

• If data is not synchronized by Windows Media Player and is

forwarded in another way, the unit may not be able to correctly play

back the files.

• A file that is copy-protected (copyright protection) cannot be played

back.

• It is recommended to back up important data on a personal

computer.

• Do not remove the USB device while playback is in progress. Change

SOURCE to something other than USB, then remove the USB device

to prevent possible damage to its memory.

• When Nokia is used as a Portable audio player:

Not all the Nokia mobile phones can be used as Portable audio

players.

If the Nokia mobile phone fails to work as a Portable audio player

while connected, set it to Mass Storage mode and reconnect to this

unit. For details, refer to Owner’s Manual of the Nokia mobile phone.

• Windows Media, and the Windows logo are trademarks, or

registered trademarks of Microsoft Corporation in the United States

and/or other countries.

• iPhone, iPod, iPod classic, iPod nano, iPod touch, and iTunes are

trademarks of Apple Inc., registered in the U.S. and other countries.

• “Made for iPod,” and “Made for iPhone,” mean that an electronic

accessory has been designed to connect specifically to iPod, or

iPhone, respectively, and has been certified by the developer to meet

Apple performance standards. Apple is not responsible for the

operation of this device or its compliance with safety and regulatory

standards.

• Pandora and the Pandora logo are registered trademarks of Pandora

Due to music licensing restrictions, the Pandora radio service is only

available in the United States.

This device will control Pandora when connected to a compatible

iPhone.

• SiriusXM and all related marks and logos are trademarks of

•The BLUETOOTH

word mark and logos are registered

trademarks owned by the Bluetooth SIG, Inc. and any use of such

marks by Alpine Electronics, Inc. is under license.

• “MPEG Layer-3 audio coding technology licensed from Fraunhofer

IIS and Thomson.”

• “Supply of this product only conveys a licence for private,

non-commercial use and does not convey a license nor imply any

right to use this product in any commercial (i.e. revenue-generation)

real time broadcasting (terrestrial, satellite, cable and/or any other

media), broadcasting/streaming via internet, intranets and/or other

networks or in other electronic content distribution systems, such as

pay-audio or audio-on-demand applications. An independent

license for such use is required. For details, please visit http://

www.mp3licensing.com”

9-EN

* The illustration is for CDE-123.

Accessory List

• Head Unit ..................................................................................1

• Power Cable ..............................................................................1

• USB Cable (CDE-123 only)........................................................1

• Interface cable for iPod (CDE-123 only) .................................1

• SiriusXM Tuner (CDE-124SXM only)........................................1

• Mounting Sleeve ......................................................................1

• Carrying Case............................................................................1

• Bracket key ...............................................................................2

• Screw (M5 × 8) ..........................................................................4

• Owner’s Manual..................................................................1 set

Turning Power On and Off

Press SOURCE to turn on the unit.

Note

• The unit can be turned on by pressing any other button except  and

e (Release).

Press and hold SOURCE for at least 2 seconds to turn

off the unit.

Note

• The first time power is turned on, the volume will start from level 12.

Source Selection

Press SOURCE to change the source.

TUNER  SIRIUSXM

 DISC  USB FRONT

/iPod FRONT



PANDOR A F

 BT AUDIO

 AUXILIARY

 TUNER

*1 Displayed only when a SiriusXM Tuner is connected.

(CDE-124SXM/CDE-123 only)

*2 Displayed only when no iPod/iPhone is connected. For

CDE-123, during USB FRONT source, you can switch to USB

REAR source by pressing BAND/F/R; for CDE-124SXM/

CDE-122, the source name is USB AUDIO.

*3 Displayed only when the iPod/iPhone is connected. For

CDE-123, during iPod FRONT source, you can switch to iPod

REAR source by pressing BAND/F/R; for CDE-124SXM/

CDE-122, the source name is iPod.

*4 The Pandora source can be displayed only when PANDORA is

set to ON. For details, refer to “Setting the Pandora Source” on

page 22. For CDE-123, during PANDORA F source, you can

switch to PANDORA R source by pressing BAND/F/R; for

CDE-124SXM/CDE-122, the source name is PANDORA.

*5 Displayed only when BT IN is set to HFP+AUDIO, refer to

“Setting the BLUETOOTH Connection” on page 19. (CDE-123

only)

*6 Refer to “Using the Front AUX Input Terminal” on page 17.

For CDE-123, during AUX source, you can switch to AUX

REAR source by pressing BAND/F/R when ON is set in “Setting

the AUX REAR Setup Mode (AUX-R SET)” (refer to “Setting the

AUX REAR Setup Mode (AUX-R SET) (CDE-123 only)” on

page 19).

Note

• You can recall your favorite source by pressing FAV directly. For details,

refer to “Set your favorite source to the FAV button (FAV SETUP)” on

page 18.

Detaching and Attaching the Front Panel

Turn off the unit power.

Press e (Release) at the lower left side until the front

panel pops out.

Grasp the left side of the front panel and pull it out.

Notes

• The front panel may become hot in normal usage (especially the

connector terminals on the back of the front panel). This is not a

malfunction.

• To protect the front panel, place it in the supplied carrying case.

• When detaching the front panel, do not apply excessive force as it may

result in malfunction.

Insert the right side of the front panel into the main unit.

Align the groove on the front panel with the projections

on the main unit.

Push the left side of the front panel until it locks firmly into

the main unit.

Getting Started

Rotary encoder/ /ENTER

SOURCE/

AUDIO/SETUP



FUNC./VIEW

BAND/ F/R

FAV





Detaching

Attaching

10-EN

Notes

• Before attaching the front panel, make sure that there is no dirt or dust

on the connector terminals and no foreign object between the front

panel and the main unit.

• Attach the front panel carefully, holding the sides of the front panel to

avoid pushing buttons by mistake.

Initial System Start-Up

Be sure to press the RESET switch when using the unit for the first time,

after changing the car battery, etc.

Turn off the unit power.

Remove the detachable front panel.

Press RESET with a ballpoint pen or similar pointed object.

Adjusting Volume

Turn the Rotary encoder until the desired sound is

obtained.

Setting the Time

Press and hold AUDIO/SETUP for at least 2 seconds to

activate the SETUP mode.

Turn the Rotary encoder to select the GENERAL mode,

and then press ENTER.

BLUETOOTH

 GENERAL  AUDIO  DISPLAY  SXM SETUP

 iPod & USB

*1 Displayed only when INT MUTE is set to OFF, and the mode is

set to other than BT AUDIO. (CDE-123 only)

*2 Displayed only when a SiriusXM Tuner is connected and the

current source is Satellite Radio (SIRIUSXM). (CDE-124SXM/

CDE-123 only)

Turn the Rotary encoder to select CLOCK ADJ, and then

press ENTER.

The time indication will blink.

Turn the Rotary encoder to adjust the hours while the

time indication is blinking, and then press ENTER.

Turn the Rotary encoder to adjust the minutes while the

time indication is blinking.

Press and hold AUDIO/SETUP for at least 2 seconds to

return to normal mode.

Notes

• To synchronize the clock to another clock/watch or radio time

announcement, press and hold ENTER for at least 2 seconds after

setting the “hour”. Minutes will reset to “00”. If the display shows over

“30” minutes when you do this, the time will advance one hour.

•Press  to return to the previous mode.

• If no operation is performed for 60 seconds, the unit will return to

normal mode automatically.

RESET switch

Controllable with Remote Control

This unit can be controlled with an optional Alpine remote control.

For details, consult your Alpine dealer.

Point the optional remote control transmitter at the remote control

sensor.

Connectable to Steering Remote Control Interface Box (CDE-123

only)

You can operate this unit from the vehicle’s control unit when an

Alpine Steering Remote Control Interface Box (optional) is

connected. For details, contact your Alpine dealer.

Remote control sensor

11-EN

* The illustration is for CDE-123.

Listening to Radio

Press SOURCE to select TUNER mode.

Press BAND repeatedly until the desired radio band is

displayed.

F1 (FM1)  F2 (FM2)  AM  F1 (FM1)

Press TUNEA.ME to select the tuning mode.

DX SEEK (Distance mode)  SEEK (Local mode)  OFF (Manual

mode)  DX SEEK

Note

• The initial mode is Distance mode.

Distance mode:

Both strong and weak stations will be automatically tuned in

(Automatic Seek Tuning).

Local mode:

Only strong stations will be automatically tuned in (Automatic

Seek Tuning).

Manual mode:

The frequency is manually tuned in steps (Manual tuning).

Press  or  to tune in the desired station.

Holding down  or  will change the frequency

continuously.

Presetting Stations Manually

While receiving the station that you want to store, press

and hold, for at least 2 seconds, any one of the preset

buttons (1 through 6) into which you wish to store the

station.

The display shows the band, preset number and station

frequency memorized.

Notes

• A total of 18 stations can be stored in the preset memory (6 stations for

each band; FM1, FM2 and AM).

• If you store a station in a preset memory which already has a station,

the current station will be cleared and replaced with the new station.

Presetting Stations Automatically

Press BAND repeatedly until the desired radio band is

displayed.

Press and hold TUNEA.ME for at least 2 seconds.

The frequency on the display continues to change while the

automatic memory is in progress. The tuner will automatically

seek and store 6 strong stations in the selected band. They will

be stored into preset buttons 1 to 6 in order of signal strength.

When the automatic memory has been completed, the tuner

goes to the station stored in preset location No.1.

Note

• If no stations are stored, the tuner will return to the original station you

were listening to before the auto memory procedure began.

Tuning to Preset Stations

Select the band, and then press any one of the station

preset buttons (1 through 6) that has your desired radio

station in memory.

The display shows the band, preset number and frequency of

the station selected.

Frequency Search Function

You can search for a radio station by its frequency.

Press and hold ENTER for at least 2 seconds in Radio

mode to activate Frequency search mode.

Turn the Rotary encoder to select the desired frequency.

Press ENTER to receive the selected frequency.

Note

•Press  in the search mode to cancel. Or, the search mode will be

canceled if no operation is performed for 10 seconds.

Radio

Rotary encoder//ENTER

SOURCE/

BAND

TUNE/A.ME





Preset buttons

(1 through 6)



12-EN

* The illustration is for CDE-123.

Playback

The following table shows which discs can be played on which models.

Insert a disc with the label side facing up.

The disc will be pulled into the unit automatically.

Note

• When a disc is already inserted, press SOURCE to switch to the

DISC mode.

While playing back MP3/WMA/AAC, press  or  to select

the desired folder.

Press  or  to select the desired track (file).

Pressing and holding  or  will fast backward/fast

forward track continuously.

To pause playback, press .

Pressing  again will resume playback.

To eject the disc, press .

Notes

• Do not remove a CD during its eject cycle. Do not load more than one

disc at a time. A malfunction may result from doing either.

•The “” indicator lights up when a disc is inserted.

• Three-inch (8 cm) CDs can not be used.

• WMA format files that are protected by DRM (Digital Rights

Management), AAC format files that have been purchased from the

iTunes Store and files that are copy-protected (copyright protection)

cannot be played back on this unit.

• The track display for MP3/WMA/AAC data playback is the file

numbers recorded on the disc.

• The playback time may not be correctly displayed when a VBR

(Variable Bit Rate) recorded file is played back.

Repeat Play

Press a 4.

The song is played back repeatedly.

 a

 (off)  a

*1 Only a track is repeatedly played back.

*2 Only files in a folder are repeatedly played back. (MP3/WMA/

AAC mode only)

To cancel repeat play, select (off) with the above

procedure.

M.I.X. (Random Play)

Press 5s.

The songs are played back in random sequence.

s

 s ALL

 (off)  s

*1 Only files in a folder are played back in random sequence.

(MP3/WMA/AAC mode only)

*2 The tracks/files are played back in random sequence.

To cancel M.I.X. play, select (off) with the above procedure.

Searching for CD Text

On discs utilizing CD Text, songs can be searched and played by using

their recorded titles. For discs without CD Text, searches are made using

the track numbers associated with each song.

Press ENTER during play.

This will set the search mode, and the “” indicator lights up.

Turn the Rotary encoder to select the desired track, and

then press ENTER.

This will play the selected track.

Notes

•Press  in the search mode to cancel. Or, the search mode is canceled

if no operation is performed for 60 seconds.

• When CD Text Search is made during M.I.X. play, the M.I.X. play

mode will be canceled.

Folder/File Name Search (concerning MP3/

WMA/AAC)

Folder and file names may be searched and displayed during playback.

During MP3/WMA/AAC playback, press ENTER to

activate the search mode.

The “” indicator lights up.

Turn the Rotary encoder to select Folder Name Search

mode, and then press ENTER.

CD/MP3/WMA/AAC

CD CD-TEXT MP3 WMA AAC

CDE-124SXM

/CDE-122



CDE-123 

Rotary encoder/ /ENTER

SOURCE/















Folder Name Search mode

13-EN

Turn the Rotary encoder to select the desired folder.

Press and hold ENTER for at least 2 seconds to play

back the first file in the selected folder.

Notes

•Press and hold  for at least 2 seconds in the search mode to cancel.

Or, the search mode is canceled if no operation is performed for

60 seconds.

• To search for files in the Folder Name Search mode, press ENTER.

Files in the folder may be searched.

•Press  to exit Folder Name Search mode in step 3 in order to select

File Name Search mode.

• The root folder is displayed as “\ROOT”.

• When Folder Name Search is made during M.I.X. play, the M.I.X. play

mode will be canceled.

During MP3/WMA/AAC playback, press ENTER to

activate the search mode.

The “” indicator lights up.

Turn the Rotary encoder to select File Name Search mode,

and then press ENTER.

Select the desired file by turning the Rotary encoder.

Press ENTER to play back the selected file.

Notes

•Press and hold  for at least 2 seconds in the search mode to cancel.

Or, the search mode is canceled if no operation is performed for

60 seconds.

•Press  in the search mode to return to the previous mode.

• When File Name Search is made during M.I.X. play, the M.I.X. play

mode will be canceled.

Quick Search

You can search for tracks (files).

Press and hold ENTER for at least 2 seconds in the CD/

MP3/WMA/AAC mode to activate Quick Search mode.

The “” indicator lights up.

Turn the Rotary encoder to select a desired track (file),

and then press ENTER.

The selected track is played back immediately.

Note

•Press  in the search mode to cancel. Or, the search mode is canceled

if no operation is performed for 10 seconds.

About MP3/WMA/AAC

CAUTION

Except for private use, duplicating audio data (including MP3/

WMA/AAC data) or distributing, transferring, or copying it,

whether for free or for a fee, without permission of the copyright

holder is strictly prohibited by the Copyright Act and by

international treaty.

What is MP3?

MP3, whose official name is “MPEG-1 Audio Layer 3,” is a compression

standard prescribed by the ISO, the International Standardization

Organization and MPEG which is a joint activity institution of the IEC.

MP3 files contain compressed audio data. MP3 encoding is capable of

compressing audio data at extremely high ratios, reducing the size of

music files to as much as one-tenth their original size. This is achieved

while still maintaining near CD quality. The MP3 format realizes such

high compression ratios by eliminating the sounds that are either

inaudible to the human ear or masked by other sounds.

What is WMA?

WMA, or “Windows Media™ Audio,” is compressed audio data.

WMA is similar to MP3 audio data and can achieve CD quality sound

with small file sizes.

What is AAC?

AAC is the abbreviation for “Advanced Audio Coding,” and is a basic

format of audio compression used by MPEG2 or MPEG4.

Method for creating MP3/WMA/AAC files

Audio data is compressed using software with MP3/WMA/AAC codecs.

For details on creating MP3/WMA/AAC files, refer to the user’s manual

for that software.

MP3/WMA/AAC files that are playable on this device have the file

extensions “mp3” / “wma” / “m4a”. Files with no extension cannot be

played back (WMA ver. 7.1, 8 and 9 are supported). Protected files are

not supported, neither are raw AAC files (using the “.aac” extension).

There are many different versions of the AAC format. Confirm that the

software being used conforms to the acceptable formats listed above.

It’s possible that the format may be unplayable even though the

extension is valid.

Playback of AAC files encoded by iTunes is supported.

Supported playback sampling rates and bit rates

MP3

WMA

AAC

This device may not play back correctly depending on sampling rates.

ID3 tags/WMA tags

This device supports ID3 tag v1 and v2, and WMA tag.

If tag data is in an MP3/WMA/AAC file, this device can display the title

(track title), artist name, and album name ID3 tag/WMA tag data.

This device can only display single-byte alphanumeric characters (up to

30 for ID3 tags and up to 15 for WMA tags) and the underscore. For

non-supported characters, “NO SUPPORT” is displayed.

If information contains characters other than ID3 tag information, the

audio file may not be played back.

The tag information may not be correctly displayed, depending on the

contents.

Producing MP3/WMA/AAC discs

MP3/WMA/AAC files are prepared, then written to a CD-R or CD-RW

using CD-R writing software. A disc can hold up to 510 files/folders

(including Root Folders), and the maximum number of folders is 255.

Playback may not be performed if a disc exceeds the limitations

described above.

Media supported

The media that this device can play back are CD-ROMs, CD-Rs, and

CD-RWs.

Corresponding File Systems

This device supports discs formatted with ISO9660 Level 1 or Level 2.

Under the ISO9660 standard, there are some restrictions to remember.

File Name Search mode

Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz, 16 kHz,

12 kHz, 11.025 kHz, 8 kHz

Bit rates: 8 - 320 kbps

Sampling rates: 48 kHz, 44.1 kHz, 32 kHz

Bit rates: 48 - 192 kbps

Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz, 16 kHz,

12 kHz, 11.025 kHz, 8 kHz

Bit rates: 16 - 320 kbps

14-EN

The maximum nested folder depth is 8 (including the root directory).

The number of characters for a folder/file name is limited.

Valid characters for folder/file names are letters A-Z (all caps), numbers

0-9, and ‘_’ (underscore).

This device also can play back discs in Joliet, Romeo, etc., and other

standards that conform to ISO9660. However, sometimes the file

names, folder names, etc., are not displayed correctly.

Formats supported

This device supports CD-ROW XA, Mixed Mode CD, Enhanced CD

(CD-Extra) and Multi-Session.

This device cannot correctly play back discs recorded with Track At

Once or packet writing.

Order of files

Files are played back in the order that the writing software writes them

to the disc. Therefore, the playback order may not be what is expected.

Verify the writing order in the software’s documentation. The playback

order of the folders and files is as follows.

* The folder No./ folder Name will not be displayed if no file is contained

in the folder.

Bit rate

This is the “sound” compression rate specified for encoding. The higher

the bit rate, the higher the sound quality, but also the larger the files.

Sampling rate

This value shows how many times per second the data is sampled

(recorded). For example, music CDs use a sampling rate of 44.1 kHz, so

the sound is sampled (recorded) 44,100 times per second. The higher

the sampling rate, the higher the sound quality, but also the larger the

volume of data.

Encoding

Converting music CDs, WAVE (AIFF) files, and other sound files into the

specified audio compression format.

Ta g

Song information such as track titles, artist names, album names, etc.,

written into MP3/WMA/AAC files.

Root folder

The root folder (or root directory) is found at the top of the file system.

The root folder contains all folders and files. It is created automatically

for all burned discs.

* The illustration is for CDE-123.

Adjusting Subwoofer Level/Bass Level/Mid

Level/Treble Level/Balance (Between Left

and Right)/Fader (Between Front and Rear)/

Loudness/Defeat

Press AUDIO repeatedly to choose the desired mode.

Each press changes the mode as follows:

SUBW

 BASS

 MID

 TREBLE

 BAL  FAD  LOUD

 DEFEAT  VOLUME  SUBW

*1 When the subwoofer mode is set to OFF, its level cannot be

adjusted, refer to “Turning Subwoofer ON/OFF” on page 16.

*2 Adjustable only when DEFEAT is OFF.

Notes

• If no operation is performed for 5 seconds, the unit automatically

returns to normal mode.

• Loudness introduces a special low- and high-frequency emphasis at low

listening levels. This compensates for the ear’s decreased sensitivity to

bass and treble sound.

Turn the Rotary encoder until the desired sound is

obtained in each mode.

By setting DEFEAT ON, previously adjusted level settings of

BASS, MID, and TREBLE will return to the factory defaults.

Terminology

Root folder

Folder MP3/WMA/AAC File

Sound Setting

Subwoofer 0 ~ +15

Bass level -7 ~ +7

Mid level -7 ~ +7

Treble level -7 ~ +7

Balance L15 ~ R15

Fader R15 ~ F15

Loudness ON/OFF

Defeat ON/OFF

Volume 0 ~ 35

Rotary encoder/ /ENTER

AUDIO/SETUP



15-EN

Sound Setting

You can flexibly customize the unit to suit your own preference and

usage. From the AUDIO SETUP menu, Audio Setting can be modified.

Press and hold AUDIOSETUP for at least 2 seconds to

activate the SETUP mode.

Turn the Rotary encoder to select AUDIO, and then press

ENTER.

BLUETOOTH

 GENERAL  AUDIO  DISPLAY  SXM SETUP

 iPod & USB

*1 Displayed only when INT MUTE is set to OFF, and the mode is

set to other than BT AUDIO. (CDE-123 only)

*2 Displayed only when a SiriusXM Tuner is connected and the

current source is Satellite Radio (SIRIUSXM). (CDE-124SXM/

CDE-123 only)

Turn the Rotary encoder to select the desired sound

setting menu, and then press ENTER.

FAC TORY EQ

*3/*4

 3BAND EQ

*3/*5

 HPF

 SUBWOOFER 

SUBW LPF

 SUBW PHASE

 SUBW SYS

*3 Adjustment cannot be performed when DEFEAT is set to ON.

*4 The FACTORY EQ’s setting value and 3BAND EQ’s setting

value are linkage.

*5 The FACTORY EQ’s setting value and 3BAND EQ’s setting

value are linkage. In step 3, three sound adjustment items (Bass,

Mid and Treble) can be selected in 3BAND EQ mode, turn the

Rotary encoder to select the desired item, and then press

ENTER to continue to step 4.

*6 These functions are inoperable when Subwoofer is set to OFF.

Turn the Rotary encoder to change the setting, and then

press ENTER.

(e.g. Select SUBWOOFER ON or SUBWOOFER OFF)

Press and hold AUDIOSETUP for at least 2 seconds to

return to normal mode.

Notes

• Pressing  returns to the previous Sound menu mode.

• If no operation is performed for 60 seconds, Sound menu mode is

canceled.

10 typical equalizer settings are preset at the factory for a variety of

musical source material.

USER  FLAT  POPS  ROCK  NEWS  JAZZ  ELEC

DANCE  HIP HOP  EASY LIS  COUNTRY  CLASSICAL

You can modify the Equalizer settings to create a response curve more

appealing to your personal taste. The setting of Bass, Mid and Treble can

be adjusted in this mode.

Setting the Bass Control

After selecting BASS from the 3BAND EQ adjustment

mode, turn the Rotary encoder to select the desired Bass

setting item, and then press ENTER.

WIDTH (Q)  CENTER FRQ  LEVEL

Turn the Rotary encoder to select the desired setting

value, and then press ENTER.

Press  to return to the previous step.

 Setting the Bass Bandwidth (WIDTH (Q))

Turn the Rotary encoder to select the desired bass

bandwidth.

WIDE 0.50  MEDIUM 1.00  MEDIUM 1.50  NARROW 2.00

Changes the boosted bass bandwidth to wide or narrow. A wider setting

will boost a wide range of frequencies above and below the center

frequency. A narrower setting will boost only frequencies near the

center frequency.

 Setting the Bass Center Frequency (CENTER FRQ)

Turn the Rotary encoder to select the desired bass center

frequency.

60 (Hz)  80 (Hz) (Initial setting)  100 (Hz)  120 (Hz)

Emphasizes the displayed bass frequency ranges.

 Setting the Bass Level

Turn the Rotary encoder to select the desired bass level

(-7~+7)

You can emphasize or weaken the bass level.

* The adjustment can also be made by pressing AUDIO. Refer to

“Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and

Rear)/Loudness/Defeat” on page 14.

Setting the Mid Control

After selecting MID from the 3BAND EQ adjustment mode,

turn the Rotary encoder to select the desired Mediant

setting item, and then press ENTER.

WIDTH (Q)  CENTER FRQ  LEVEL

Turn the Rotary encoder to select the desired setting

value, and then press ENTER.

Press  to return to the previous step.

 Setting the Mid Bandwidth (WIDTH (Q))

Turn the Rotary encoder to select the desired Mid

bandwidth.

WIDE 0.75  MEDIUM 1.00  MEDIUM 1.25  NARROW 1.50

 Setting the Mid Center Frequency (CENTER FRQ)

Turn the Rotary encoder to select the desired Mid center

frequency.

500 (Hz)  1.0k (Hz) (Initial setting)  1.5k (Hz)  2.5k (Hz)

Use steps 1 to 5 to select one of the setting modes to modify.

See the applicable section below for details about the

selected setting item.

Equalizer Presets (FACTORY EQ)

Adjusting the Parametric Equalizer Curve

(3BAND EQ)

16-EN

 Setting the Mid Level

Turn the Rotary encoder to select the desired Mid level (-7

~ +7)

You can emphasize or weaken the Mid level.

* The adjustment can also be made by pressing AUDIO. Refer to

“Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and

Rear)/Loudness/Defeat” on page 14.

Setting the Treble Control

After selecting TREBLE from the 3BAND EQ adjustment

mode, turn the Rotary encoder to select the desired

Treble setting item, and then press ENTER.

WIDTH (Q)  CENTER FRQ  LEVEL

Turn the Rotary encoder to select the desired setting

value, and then press ENTER.

Press  to return to the previous step.

 Setting the Treble Bandwidth (WIDTH (Q))

Turn the Rotary encoder to select the desired treble

bandwidth.

WIDE 0.75  NARROW 1.25

 Setting the Treble Center Frequency (CENTER FRQ)

Turn the Rotary encoder to select the desired treble

center frequency.

7.5K (Hz)  10.0K (Hz) (Initial setting)  12.5K (Hz)  15.0K (Hz)

 Setting the Treble Level

Turn the Rotary encoder to select the desired treble level

(-7~+7)

You can emphasize or weaken the treble level.

* The adjustment can also be made by pressing AUDIO. Refer to

“Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and

Rear)/Loudness/Defeat” on page 14.

The High Pass Filter on this unit can be adjusted to suit your personal

taste.

 Setting item: HPF

Setting contents:

OFF (Initial setting) / 60 (Hz) / 80 (Hz) / 120 (Hz) / 160 (Hz)

All frequencies above the selected cutoff are output.

When the subwoofer is on, you can adjust the subwoofer output level

(refer to “Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and Rear)/

Loudness/Defeat” on page 14).

 Setting item: SUBWOOFER

Setting contents:

ON (Initial setting) / OFF

ON:

The subwoofer signal is output from the Subwoofer RCA

Connectors (refer to “Connections” on page 42).

OFF:

No subwoofer signal is output from the Subwoofer RCA

Connectors (refer to “Connections” on page 42).

The Low Pass Filter on this unit can be adjusted to suit your personal

taste.

 Setting item: SUBW LPF

Setting contents:

OFF (Initial setting) / LPF 60 (Hz) / LPF 80 (Hz) / LPF 120 (Hz) /

LPF 160 (Hz)

All frequencies lower than the selected cutoff are output.

The subwoofer output phase is toggled SUBWOOFER NORMAL (0°) or

SUBWOOFER REVERSE (180°). To adjust the level, turn the Rotary

encoder.

 Setting item: SUBW PHASE

Setting contents:

NORMAL (Initial setting) / REVERSE

When the subwoofer is on, you can select either SYS 1 or SYS 2 for the

desired subwoofer effect.

 Setting item: SUBW SYS

Setting contents:

SUBW SYS 1 (Initial setting) / SUBW SYS 2

SUBW SYS 1:

Subwoofer level changes according to the main volume setting.

SUBW SYS 2:

Subwoofer level change is different from the main volume setting.

For example, even at low volume settings, the subwoofer is still

audible.

Adjusting the High Pass Filter

Turning Subwoofer ON/OFF

Adjusting the Low Pass Filter

Setting the Subwoofer Phase

Setting the Subwoofer System

17-EN

* The illustration is for CDE-123.

Displaying the Text

Text information, such as the disc name and the track name, will be

displayed if playing a CD text compatible disc. It is also possible to

display the folder name, the file name and the tag, etc., while playing

MP3/WMA/AAC files.

Press VIEW.

The display will change every time the button is pressed.

Note

• When the TEXT SCR is set to SCR MANUAL, press and hold  for at

least 2 seconds, the current text will be scrolled one time (except Radio

mode).

The display in Radio mode:

FREQUENCY  CLOCK  FREQUENCY

The display in CD mode:

TRACK NO./ELAPSED TIME  TRACK NO./CLOCK  TEXT (DISC

NAME)

 TEXT (TRACK NAME)

 TRACK NO./ELAPSED TIME

The display in MP3/WMA/AAC mode:

FILE NO./ELAPSED TIME  (FOLDER NO./FILE NO.)

 FILE NO./

CLOCK  FOLDER NAME  FILE NAME  ARTIST NAME



ALBUM NAME

 SONG NAME

 FILE NO./ELAPSED TIME

*1 Displayed during playback of a disc with CD text.

*2 Only for MP3/WMA/AAC disc mode.

*3 ID3 tag/WMA tag

If an MP3/WMA/AAC file contains ID3 tag/WMA tag

information, the ID3 tag/WMA tag information is displayed

(e.g., song name, artist name, and album name). All other

tag data is ignored.

When displaying Text, the following indicators are lit according to the

mode.

*1 Tag information:

If there is no tag information, “ARTIST”/“ALBUM”/“SONG” is

displayed.

*2 The root folder is displayed as “\ROOT”.

*3 If there is no Text (Disc Name or Track Name), “DISC TEXT”/

“TRACK TEXT” is displayed.

*4 If there is no text information, nothing will be displayed.

Text compatible CDs contain text information such as the disc name and

track name. Such text information is referred to as “text”.

Notes

• Some characters may not be displayed correctly with this device,

depending on the character type.

• “NO SUPPORT” is displayed when the desired text information cannot

be displayed on this unit.

• The text or tag information may not be correctly displayed, depending

on the contents.

Using the Front AUX Input Terminal

Connect a portable music player, etc. by simply connecting it to the

input on the front panel. An optional adapter cable is required (standard

RCA to 3.5ø mini-phono plug or 3.5ø to 3.5ø mini phono plug).

Other Functions

SOURCE/

VIEW

BAND/ F/R



About the indication display

Indica-

tor/

Mode

CD Mode

MP3/WMA/

AAC/USB

AUDIO

Mode

iPod/

iPhone

Mode

Satellite

Radio

mode

 —

Folder

Name

being dis-

played

——

 —

Artist

Name

being dis-

played

Artist

Name

being dis-

played

Artist

Name

being dis-

played



Text (Disc

Name

)

being dis-

played

Album

Name

being dis-

played

Album

Name

being dis-

played

Content

info.

being dis-

played



Text ( Track

Name

)

being dis-

played

Song

Name

File Name

being dis-

played

Song

Name

being dis-

played

Song Title

being dis-

played

 ———

Alpine CDE-122 Le manuel du propriétaire

Marque: Alpine

Modèle: CDE-122

Catégorie: Lecteurs MP3 / MP4

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Alpine CDE-122 Owner's manual

Alpine CDE-122 Le manuel du propriétaire

Ce manuel convient également à

Alpine CDE-122 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents