Extron electronics XPA Ultra Series Manuel utilisateur

Marque: Extron electronics

Modèle: XPA Ultra Series

Catégorie: Matériel musical

Taper: Manuel utilisateur

Ce manuel convient également à

User Guide

XPA U 1004 SB and

XPA U 2002 SB

XPA Ultra Series

Half-Rack Audio Power Ampliﬁers

68‑3579‑01 Rev. A

02 21

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on

the product, is intended to alert the user of the

presence of uninsulated dangerous voltage within

the product’s enclosure that may present a risk of

electric shock.

ATTENTION: This symbol, , when used on the

product, is intended to alert the user of important

operating and maintenance (servicing) instructions in

the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68‑290‑01, on the Extron website,

www.extron.com.

Sicherheitsanweisungen • Deutsch

WARUNG: Dieses Symbol auf demProdukt soll

den Benutzer darauf aufmerksam machen, dass im

Inneren des Gehäuses dieses Produktes gefährliche

Spannungen herrschen, die nicht isoliert sind und

die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll

dem Benutzer in der im Lieferumfang enthaltenen

Dokumentation besonders wichtige Hinweise zur

Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF‑Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den

Extron‑Richtlinien für Sicherheit und Handhabung (Artikelnummer

68‑290‑01) auf der Extron‑Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza

en el producto, avisa al usuario de la presencia

de voltaje peligroso sin aislar dentro del producto,

lo que puede representar un riesgo de descarga

eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza

en el producto, avisa al usuario de la presencia de

importantes instrucciones de uso y mantenimiento

estas estan incluidas en la documentación

proporcionada con el equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad de

Extron, referencia 68‑290‑01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il

est utilisé sur le produit, signale à l’utilisateur la

présence à l’intérieur du boîtier du produit d’une

tension électrique dangereuse susceptible de

provoquer un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il

est utilisé sur le produit, signale à l’utilisateur

des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation

fournie avec l’équipement.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation,

la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les

informations de sécurité et de conformité Extron, réf. 68‑290‑01, sur le site

Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto,

serve ad avvertire l’utente della presenza di tensione

non isolata pericolosa all’interno del contenitore del

prodotto che può costituire un rischio di scosse

elettriche.

ATTENTZIONE: Il simbolo, , se usato sul

prodotto, serve ad avvertire l’utente della presenza

di importanti istruzioni di funzionamento e

manutenzione nella documentazione fornita con

l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento alla Guida

alla conformità normativa e di sicurezza di Extron, cod. articolo 68‑290‑01, sul

sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego

napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji

(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej

zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron

bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01,

na stronie internetowej Extron, www.extron.com.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户, 该产品机壳内有暴露的危险

电压，有触电危险。

注意：产品上的这个标志意在提示用户, 设备随附的用户手册中有重

要的操作和维护(维修)说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使

用的特性等相关内容，

敬请访问 Extron 网站 , www.extron.com，参见 Extron 安全规范指南，产品编号

68-290-01。

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在未隔離的危險

電壓，可能會導致觸電之風險。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有重要

的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊，

請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手

冊》，準則編號 68-290-01。

안전 지침 • 한국어

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению электрическим

током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций по

эксплуатации и обслуживанию в руководстве, прилагаемом к

данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других вопросах

см. руководство по безопасности и соблюдению нормативных

требований Extron на сайте Extron: , www.extron.com,

номер по каталогу - 68-290-01.

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수 안내서, 68-

290-01 조항을 참조하십시오.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

), registered service marks (

), and trademarks (

) are the property of RGBSystems, Inc. or Extron (see the

current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, GlobalConfigurator,

GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NAV,

NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

SystemINTEGRATOR, TeamWork, TouchLink, V‑Lock, VideoLounge, VN‑Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu‑RATEFrameLock), ADSP(Advanced Digital Sync Processing), Auto‑Image, AVEdge, CableCover, CDRS(ClassD Ripple

Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator,

DSVP(Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti‑Torque,

PendantConnect, ProDSP, QS‑FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope‑Trigger, SIS, SimpleInstructionSet, Skew‑Free,

SpeedNav, Triple‑Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class B Notice

NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part15 of the FCC rules. These limits provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. There is no

guarantee that interference will not occur. If this equipment does cause interference to radio

or television reception, which can be determined by turning the equipment off and on, you

are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

In order to maintain compliance with FCC regulations, shielded cables must be used with

this equipment. Operation with non-approved equipment or unshielded cables is likely to

result in interference to radio and TV reception. The user is cautioned that changes and

modifications made to the equipment without the approval of the manufacturer could void

the user’s authority to operate this equipment.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics see the Extron Safety and Regulatory

Compliance Guide on the Extron website.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION: Risk of property damage.

Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

viXPA U 1004 SB and XPA U 2002 SB • Table of Contents

Contents

Introduction ................................................1

About this Guide .................................................. 1

Features .............................................................. 2

Installation .................................................. 4

Mounting the XPA Ultra Series Ampliﬁer ............... 4

Tabletop Use ................................................... 5

UL Rack Mounting Guidelines .......................... 6

Rack Mounting ................................................ 5

Rack Ear Mounting .......................................... 5

Bridge Plate Rack Mounting ............................ 6

Rack Shelf Mounting........................................ 7

Flexible Conduit Adapter Kit Installation ............... 8

Operation..................................................12

Front Panel Features .......................................... 12

Rear Panel Features .......................................... 13

Remote Standby Port ........................................ 17

Troubleshooting ........................................ 17

Ampliﬁer Fails to Exit Standby Mode Promptly ... 17

Ampliﬁer Enters Standby Mode Too Early .......... 19

Limiter/Protect LED Warning Indicators ............. 19

Over Temp Indicator LED ................................... 19

Extron Warranty ........................................20

XPA U 1004 SB and XPA U 2002 SB • Introduction 1

Introduction

This section gives an overview of the Extron XPA Ultra Series: XPA U 1004 SB and XPA U

2002 SB Half-Rack Four-Channel/Two-Channel audio power amplifiers. Topics include:

• About this Guide

• About the XPA U 1004 SB and XPA U 2002 SB

• Features

About this Guide

This guide describes the XPA U 1004 SB and XPA U 2002 SB Half Rack Four-Channel/Two-

Channel audio power amplifiers and discusses how to install, configure, and operate them.

In this guide, the terms “unit”, “amplifier”, and “power amplifier” refer to the

XPA U 1004 SB and XPA U 2002 SB.

About the XPA U 1004 SB and XPA U 2002 SB

The Extron XPA U 1004 SB and XPA U 2002 SB are ENERGY STAR qualified four- and

two-channel audio power amplifiers with flexible channel pairs that can drive 8 ohm, 4 ohm,

70volt, or 100 volt loads. The XPA U 1004 SB’s two individually bridgeable pairs can deliver

two 100 watt channels into low-impedance systems or one 200 watt channel into low- or

high-impedance systems. The XPA U 2002 SB’s bridgeable output pair can deliver two

200 watt channels into low-impedance systems or one 400 watt channel into low- or high-

impedance systems.

Output mode selection is made via a rear panel rotary switch for quick and easy setup.

The convection-cooled, plenum-rated enclosures of the XPA U 1004 SB and XPA U 2002

SB don’t require empty rack spaces for ventilation and include rack mount hardware. They

feature a highly efficient advanced Class D amplifier design with defeatable auto standby,

fast wake up from standby, and patented Extron CDRS (Class D Ripple Suppression)

technology. Remote volume and mute control is possible per channel pair from Extron VCM,

VC, and select MediaLink controllers.

XPA U 1004 SB and XPA U 2002 SB • Introduction 2

Features

• Selectable output modes per channel pair:

• XPA U 1004 SB

• Two 100 watt channels into 8 ohms or 4 ohms

• One 200 watt bridged channel into 70V or 100V, with or without HPF

• One 200 watt bridged channel into 8 ohms or 16 ohms

• — Allows this amplifier model to be used in a wide variety of system configurations

• XPA U 2002 SB

• Two 200 watt channels into 8 ohms or 4 ohms

• One 400 watt bridged channel into 70V or 100V, with or without HPF

• One 400 watt bridged channel into 8 ohms or 16 ohms

• — Allows this amplifier model to be used in a wide variety of system configurations

• ENERGY STAR

qualified amplifiers — The XPA U 1004 SB and the XPA U 2002 SB

are ENERGY STAR qualified and energy efficient amplifiers, conserving energy and reducing

costs.

• Extron Patented CDRS (Class D Ripple Suppression) Technology — CDRS is an

Extron pantented technology providing a smooth and clean audio waveform, and improving

signal fidelity over Class D amplifier designs.

• CDRS eliminates the high frequency switching ripple characteristics of Class D

amplifiers, a source of RF emissions which can interfere with sensitive AV equipment

like wireless mircophones.

• Convection cooled and fanless operation ‑ can be stacked without extra rack space for

• ventilation — The XPA U 1004 SB and the XPA U 2002 SB do not have internal fans or

vents for cooling, ensuring quiet reliable operation. The units generate substantially less

heat than conventional power amplifiers, making the XPA Ultra Series ideal for rack-mount

applications where space is limited.

• See Rack Mounting Ventilation Recommendations on page7.

• Defeatable auto-standby with fast wake up — The amplifiers meet ENERGY STAR

qualification requirements with an auto-standby feature that automatically places the

units into standby after 25 minutes of in activity; thereby dramatically reducing power

consumption. The XPA U 1004 SB and XPA U 2002 SB quickly return to full power in less

100 ms upon signal detection, with minimal inrush current. Auto-standby can be disabled if

required.

• UL 2043 Plenum rated when used with the optional Flexible Conduit Adapter Kit/

AV equipment — The XPA U 1004 SB and XPA U 2002 SB amplifiers meet UL 2043

when installed with the Flexible Conduit Adapter Kit, part # 70-228-02. The amplifiers must

meet this requirement for heat and smoke release for installation within a plenum airspace.

Above-the-ceiling placement conceals the amplifier to prevent theft, and it is convenient for

installing when space inside the room is limited.

• Remote volume and mute control per channel pair — With Extron VCM, VC, and

select MediaLink controllers.

• All rated watts are usable with all channels driven — With a XPA Ultra, designs can

utilize 100% of the rated power.

• Professional grade signal-to-noise and THD+N performance — The XPA U 1004 SB

and the XPA U 2002 SB both deliver professional grade performance, featuring 100 dB

signal-to-noise ratio and THD+N of less than 0.1%.

XPA U 1004 SB and XPA U 2002 SB • Introduction 3

• Ultra low inrush current at power up - no need for power sequencing — Allows

multiple XPA Ultra amplifier to be powered on simultaneously without overloading power

circuits. This eliminates the need for power sequencing.

• Power factor correction - removes harmonic content on AC line — The XPA U

1004 SB and XPA U 2002 SB features power factor correction technology that smooths

out the high peak currents of the amplifier’s current draw, minimizing the presence of

high frequency harmonics on the AC power line, preventing audible artifacts from being

transmitted to other audio equipment in the system.

• Rear panel recessed, detented level controls — Provides attenuation of input signal

for adjusting audio system gain staging. These controls are lcoated on the rear panel to

prevent tampering with the level adjustments. Laser etched markings provide enhanced

visibility of settings for ease of configuration.

• Remote standby port — Enables the XPA U 1004 SB and XPA U 2002 SB to be

remotely powered down when not in use, reducing operating cost.

• Automatic clip limiter — Detects actual onset of clipping. Gain is automatically

reduced without audible artifacts to prevent clipping distortion.

• Multiple protection circuits — Activate during output shorts, thermal overload, or DC

faults to prevent damage to the amplifier and speakers.

• 5 mm screw-lock captive screw speaker connectors — Enable simple, secure

connections with 22 to 12 AWG speaker cables.

• Front and rear-mounted signal and protection indication LEDs — Provide

convenient indication of input signal presence and protection circuit activation from both

sides of an equipment rack.

• Front panel over-temperature LED — Provides visual indication that the amplifier’s

temperature has exceeded the optimal value, well in advance of the onset of thermal

protection circuitry.

• Internal Extron Everlast

™

power supply — Provides worldwide power compatibility,

with high-demonstrated reliability and low power consumption for reduced operating

cost.

• Extron Everlast Power Supply is covered by a 7-year parts and labor warranty.

XPA U 1004 SB and XPA U 2002 SB • Installation 44

Installation

This section describes the installation and setup of the XPA U 1004 SB and XPA U 2002 SB.

Topics include:

• Mounting the XPA Ultra Series Amplifiers

• Flexible Conduit Adapter Kit Installation

Mounting the XPA Ultra Series Amplifiers

The XPA U 1004 SB and XPA U 2002 SB can be mounted in a rack using rack ears,

mounted on a rack shelf, set on a table, or mounted in the plenum space above a ceiling-

mounted projector. Also, two amplifiers can be connected using the bridging plate to create

a full rack-width unit.

This guide uses images of the XPA U 1004 SB to describe installation, but both amplifiers

are installed the same way.

Tabletop Use

Four self-adhesive rubber are included. Attach one foot at each corner on the bottom side

of the amplifier and place the unit in a desired location.

UL Rack Mounting Guidelines

The following Underwriters Laboratories (UL) guidelines pertain to the safe installation of the

equipment in a rack.

• Elevated operating ambient temperature — If the equipment is installed in a closed

or multi-unit rack assembly, the operating ambient temperature of the rack environment

may be greater than room ambient temperature. Therefore, install the equipment in an

environment compatible with the maximum ambient temperature (TMA = +32° F to

+122° F (0° C to +50° C)/ 10% to 90%, noncondensing) specified by Extron.

• Reduced air flow — Install the equipment in a rack so the amount of air flow required

for safe operation of the equipment is not compromised.

• Mechanical loading — When mounting the equipment in the rack, ensure uneven

mechanical loading does not cause a hazardous condition.

• Circuit overloading — When connecting the equipment to the supply circuit, consider

the effect circuit overloading might have on overcurrent protection and supply wiring.

Consider equipment nameplate ratings when addressing this concern.

• Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted

equipment. Pay particular attention to supply connections other than direct connections

to the branch circuit (for example, use of power strips).

XPA U 1004 SB and XPA U 2002 SB • Installation 5

Rack Mounting

The XPA U 1004 SB and XPA U 2002 SB can both be mounted onto a rack using one of

the following methods.

Rack Ear Mounting

The XPA U 1004 SB and XPA U 2002 SB ship with a set of rack ears, so that the half rack-

width amplifiers can be installed in a full rack-width space.

Mount the amplifier with the rack ears by doing the following:

1. Remove the rubber feet from the bottom of the amplifier if previously installed.

2. Attach the included rack ears to the sides of the amplifier with the four provided #6

machines screws (

XPA U

100

4 SB

1 2 3 4

TEMP

LIMITER/PROTECT

SIGNAL

POWER A

MPLIFIER

Figure 1. Installing XPA Ultra Rack Ears

3. Insert the amplifier into the rack and align the holes in the rack ear with the holes on the

rack.

4. Secure the amplifier to the rack using four provided 10-32 x 3/4” screws (see figure 2,

100

4 SB

1 2 3

OVER

TEMP

IMITER/PR

OTEC

SIGN

FIER

Figure 2. Secure XPA Ultra Amplifier to Rack

Bridge Plate Rack Mounting

The XPA U 1004 SB and XPA U 2002 SB ships with a bridge plate connector to allow two

amplifiers to be connected together and form a full rack-width unit.

Mount two XPA Ultra Series amplifiers by doing the following:

1. If the rubber feet are installed on the bottom of the amplifier, remove them.

2. Position two amplifiers upside down and next to each other.

3. Use the bridge plate connector and the four provided #4 machine screws to connect

the two amplifiers together (see figure 3,

4. Attach the two short rack ears to the amplifiers with four provided #6 machine screws

(

XPA U 1004 SB and XPA U 2002 SB • Installation 6

XPA U 1004 SB

1 2 3 4

OVER

TEMP

LIMITER/PROTECT

SIGNAL

POWER AMPLIFIERS

XPA U 1004 SB

1 2 3 4

OVER

TEMP

LIMITER/PROTECT

SIGNAL

POWER AMPLIFIERS

Mounting

screws (4)

Figure 3. Installing XPA Ultra Series Bridge Plate

5. Insert the amplifiers into the rack and align the holes in the rack ears with the holes in

the rack.

6. Secure the amplifiers to the rack using four provided 10-32 3/4” screws (see figure 4,

)

XPA U 1004 SB

1 2 3 4

OVER

TEMP

LIMITER/PROTECT

SIGNAL

POWER AMPLIFIERS

XPA U 1004 SB

1 2 3 4

OVER

TEMP

LIMITER/PROTECT

SIGNAL

POWER AMPLIFIERS

Figure 4. Secure Connected XPA Ultra Amplifiers to Rack

Rack Shelf Mounting

The XPA U 1004 SB and XPA U 2002 SB can both be mounted in a shelf using the optional

RSU 129 1U Universal Rack Shelf Kit.

Mount the amplifier with the shelf as follows:

1. If the rubber feet are installed on the bottom of the amplifier, remove them.

2. Place the amplifier on one half of the rack shelf.

3. Align the front of the amplifier with the front of the shelf, and align the threaded holes on

the bottom of the amplifier with the holes in the rack shelf.

4. Attach the amplifier to the rack shelf with the two provided 4-40 x 3/16” machine

screws. Fasten them into diagonally opposite corners by inserting the screws from the

underside of the shelf.

5. Either attach the false front panel, which is provided with the rack shelf, to the

unoccupied side of the rack, or install a second half rack-width device to that side.

Repeat steps 1 through 5 if a second device is being installed.

XPA U 1004 SB and XPA U 2002 SB • Installation 7

6. Attach the rack to the shelf by using the four 10-32 x 3/4” screws provided with the

shelf. Insert the screws through #10 beveled washers, then through the holes in the

rack (see Figure 5, below).

(2) 4-40 x 3/16"

Screws

RSU 129

1U Universal Rack Shelf

False faceplate

uses 2 screws.

Use 2 mounting holes

on opposite corners.

RIES

3 4

OVER

TEM

/PROTECT

SIG

OWE

Figure 5. Mounting the Ampliﬁer onto a Rack Shelf

ATTENTION:

• Using screws longer than 3/16” will damage the unit and void the warranty.

• L’utilisation de vis plus longues que 3/16” endommagera l’unité et annulera la

garantie.

Rack Mounting Ventilation Recommendations

Excessive heat decreases the optimal lifetime of the power amplifier. An Over Temp indicator

LED on the front panel of the amplifier lights red whenever the recommended operating

temperature has been exceeded.

The XPA Ultra amplifiers need to be arranged in a rack environment, so that the environment

around the amplifier does not reach or go beyond +122 °F (+50 °C). No more than four

amplifiers should be stacked vertically without an open space in between, as seen in figure

Vent Space

Figure 6. Vent Space Example

The XPA Ultra amplifiers can be arranged above or below another non-XPA Ultra device. The

environment around the amplifier should still not reach or go beyond +122 °F (+50 °C).

XPA U 1004 SB and XPA U 2002 SB • Installation 8

Flexible Conduit Adapter Kit Installation

WARNING :

AVERTISSEMENT :

• The circuit breaker used for this connection should be rated no lower than 20 amps and no

greater than 30 amps.

• Le disjoncteur utilisé pour cette connexion devrait avoir une cote comprise entre 20 et

30 amps.

• This unit must be installed in accordance with the National Electrical Code and with all

local codes.

• Cet appareil doit être installé conformément au National Electrical Code et à tous les

codes locaux.

• An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each

pole shall be incorporated in the electrical installation of the building, The installation

shall be carried out in accordance with all applicable installation rules.

• Un interrupteur omnipolaire avec une séparation contact d’au moins 3 mm dans

chaque pôle, devra être incorporée dans l’installation électrique du bâtiment.

L’installation doit être réalisée conformément à toutes les règles d’installation

applicables.

• Installation and service must be performed by a qualiﬁed electrician only.

• L’installation et l’entretien doivent être effectués uniquement par un électricien qualiﬁé.

• Make sure the source device and the XPA are turned off and disconnected from the

power source before you begin.

• Vériﬁez que l’appareil source et le périphérique source sont éteints et déconnectés de

la source d’alimentation avant de commencer.

• To reduce the risk of ﬁre or electric shock, do not expose this apparatus to rain or

moisture.

• Aﬁn de réduire les risques d’incendie ou de choc électrique, protégez cet appareil de

la pluie ou de l’humidité.

• The product is a Class I product, which must be connected only to a mains socket

outlet with a protective earthing (grounding) connection.

• Ce produit est un produit de Classe I, qui doit être connecté seulement à une prise

femelle secteur équipée d’une connexion de mise à la terre.

• The mains plug/appliance coupler is used as the disconnect device and shall remain

readily operable.

• La ﬁche secteur / le coupleur d’appareil est utilisé comme dispositif de déconnexion et

doit rester facilement utilisable.

ATTENTION:

• A UL-Listed electrical distribution box is recommended for the termination of

the conduit opposite the PS 124 power supply or the XPA ampliﬁer. See UL

Requirements below.

• Un boîtier de distribution électrique certifié UL est recommandé pour la terminaison du conduit à

l’opposé de l’alimentation PS 124 ou de l’amplificateur XPA. Voir “UL Requirements” on page

The optional Flexible Conduit Adapter Kit includes the following parts:

• One conduit adapter plate (pre-attached), for PS 124 and XPA Series amplifiers

• One conduit adapter plate for XPA Ultra Series and NetPA Ultra Series amplifiers

(not attached)

XPA U 1004 SB and XPA U 2002 SB • Installation 9

• One 6 foot long electrical conduit

• Three 7.5 foot, 18-gauge power wires with spade connectors

• Three auxiliary crimp-style spade connectors designed for 14- to 16-gauge wires

• One UL-rated zip tie wrap

The kit provides a way to replace the IEC power cord with a conduit, where required by

local codes.

NOTE: If needed, Extron recommends using a UL-rated crimp tool to terminate the spade

connectors. One recommended choice is the Molex crimp tool.

UL Requirements

The Underwriters Laboratories (UL) requirements listed below pertain to the installation

of the flexible conduit onto an XPA U 1004 SB and XPA U 2002 SB.

• This unit must not be used beyond its rated voltage range.

• This unit must be wired to a UL-Listed distribution box.

NOTE: The UL-approved electrical distribution box is not included with either the XPA

Ultra or the Flexible Conduit Adapter Kit. The installer is responsible for obtaining and

installing the box.

Installing the Flexible Conduit Adapter Kit

WARNING: Electrostatic discharge (ESD) can damage IC chips even though you cannot feel

it. You must be electrically grounded before touching anything inside the XPA. A grounding

wrist strap is recommended.

AVERTISSEMENT : Les décharges électrostatiques peuvent endommager les puces de circuit

même si vous ne pouvez pas les sentir. Vous devez être électriquement relié à la terre avant

de toucher un élément à l’intérieur du XPA. Un braceletde mise à la terreest recommandé.

Install the flexible conduit to the XPA Ultra Amplifier as follows:

1. Unplug the IEC power cord from the amplifier.

2. Remove the 8 screws from the top, sides, and bottom of the amplifier then slide and lift

the cover off.

(

)

100-240V

--A, 50-60 Hz

3 4

CLASS 2 WIRING

∞

GCV

STANDBY

SIGNAL

LIMITER/

PROTECT

LIMITER/

PROTECT

3 4

ATTENUATION

OUTPUT MODE

INPUTS

REMOTE OUTPUTS

XPA U 1004 SB

(

)

& 2

BRI DGED

MON O

70V

70V HPF OFF )

100 V

100 V (H PF O FF)

STE REO

& 4

8Ω/ 4Ω

8Ω

BRI DGED

MON O

70V

70V HPF OFF )

100 V

100 V (H PF O FF)

STE REO

8Ω/ 4Ω

8Ω

3&4

1&2

Remove (8)

screws

Slide cover forward and

lift straight up.

Figure 7. Removing the Cover

XPA U 1004 SB and XPA U 2002 SB • Installation 10

3. Remove the two screws holding the blue hot line and the brown neutral wires from the

terminal block on the PCB. Put the screws to the side to be used later (see figure 8 on

page10).

4. Remove the ground wire nut from the grounding stud located on the bottom of the

enclosure as shown in figure 8, below. Place the nut with the other screws to be used

later.

5. Remove the wires attached to the IEC connector from the body of the amplifier, and

slide the IEC connector and wire up and out of the amplifier’s enclosure (see figure 8,

below).

Disconnect cables

and r

emove IEC

connector

Blue Wire

Brown Wir

Remove nut

Figure 8. Removing the IEC Connector

6. Remove the washer at the end of the conduit (see Washer-B in figure 9), and remove

the conduit adapter plate that ships attached to the conduit.

Separate adapter plate

and washer from conduit

Washer-B

Washer-A

Conduit Adapter Plate

Figure 9. Removing the Existing Adapter Plate

7. Place the adapter plate that ships with the conduit kit on the conduit itself with the flat

side of the plate facing the hexgonal nut, and secure the new plate to the conduit with

the washer that was removed in step 6 (see figure 10).

Place the adapter plate

with the ﬂat side against

washer-A and secure with

washer-B.

Washer-B

Washer-A

NetPA Ultra Series Conduit

Adapter Plate

Figure 10. Secure XPA Ultra Series Adapter Plate to Conduit

8. Thread the blue, brown, and green 18-gauge power wires that are included with the

flexible conduit adapter kit through the length of the electrical conduit.

XPA U 1004 SB and XPA U 2002 SB • Installation 11

9. Install the conduit with the new conduit plate attached into the opening from where the

IEC connector removed in step 5 (see figure 11 on page11).

10. Connect the blue hot (line) and the brown neutral wires to the terminal block on the PCB

using the two screws removed back in step 3. Use the included zip tie wrap to secure

the two wires together close to the terminals (see figure 11 on page11).

WARNING: Ensure that you observe correct wire polarity. The following illustration

shows the location of the hot (line) and neutral terminals.

AVERTISSEMENT : Respecter la polarité correcte des câble. L’illustration suivante

indique l’emplacement des bornes de ligne et de neutre.

Slide IEC

connector

plate and

conduit into

enclosue.

50-60Hz

100-240V 1.3A

Blue Wire

Brown Wire

Tie Wrap

Grounding Nut

Figure 11. Install the Conduit Assembly

11. Connect the ground wire, as shown in figure 13 above, to the grounding stud located

on the bottom of the enclosure using the nut removed in step 4. Remove the ground

wire nut from the grounding stud located on the bottom of the enclosure as shown in

figure 11, above. Place the nut with the other screws to be used later.

12. Replace the cover of the XPA Ultra amplifier by reattaching the eight screws removed in

step 2. Remove the 8 screws from the top, sides, and bottom of the amplifier then slide

and lift the cover off.

XPA U 1004 SB and XPA U 2002 SB • Installation 1212

Operation

This section describes the installation and setup of the XPA U 1004 SB and XPA U 2002 SB.

Topics include:

• Front Panel Features

• Rear Panel Features

• Troubleshooting

Front Panel Features

XPA U 1004 SB

1234

OVER

TEMP

LIMITER/PROTECT

SIGNAL

POWER AMPLIFIERS

XPA U 2002 SB

OVER

TEMP

LIMITER/PROTECT

SIGNAL

POWER AMPLIFIERS

Power/Standby Indicator

Over Temp Indicator

Channel Status LEDs

Figure 12. XPA U 1004 SB and XPA U 2002 SB Front Panels

Power/Standby LED — A single LED that lights green when the unit is on and active,

and lights amber when:

• The unit is in standby mode, which turns off all outputs from the amplifier although

the amplifier still receives power.

• The unit will not come out of standby when DC voltage is detected. The amplifier

only comes out of standby mode by either resetting the device or powering it down.

NOTE: Power indicator LED may stay lit amber for a short time after removing the AC

Power Supply. This is normal.

Over Temp Indicator — A single LED that lights red when the amplifier has exceeded

the maximum recommended operating temperature. The amplifier recovers once the

unit has cooled down to below the maximum recommended operating temperature.

Power limiting may occur, but it depends on the unit’s temperature.

XPA U 1004 SB and XPA U 2002 SB • Operation 13

Channel Status LEDs — (see figure 12 on page12) Two rows of LEDs that

represent the amplifier’s channels.

• Limiter/Protect LED — The LEDs lights red when the channel is in protection

mode, which is triggered by any of the limiter protection circuits such as:

• When the clip limiter is activiated due to excessive clipping.

• When the output short circuits.

• Signal LED — The LEDs light green when the input signal is detected.

NOTE: The LEDs are also located on the rear panel.

Rear Panel Features

(

)

100-240V

--A, 50-60 Hz

CLASS 2 WIRING

∞

GCV

STANDBY

SIGNAL

LIMITER/

PROTECT

LIMITER/

PROTECT

ATTENUATION OUTPUT MODE

INPUTS

REMOTEOUTPUTS

XPA U 1004 SB

(

)

BRIDGED

MONO

70V

70V (HPF OFF)

100V

STEREO

4Ω

8Ω

16Ω

BRIDGED

MONO

70V

70V (HPF OFF)

100V

100V (HPF OFF)

STEREO

4Ω

8Ω

3&4

1&2

16Ω

100-240V

--A, 50-60 Hz

CLASS 2 WIRING

∞

GCV

STANDBY

SIGNAL

LIMITER/

PROTECT

ATTENUATION OUTPUT MODE

INPUTS

REMOTEOUTPUTS

XPA U 2002 SB

(

)

BRIDGED

MONO

70V

70V (HPF OFF)

100V

100V (HPF OFF)

STEREO

4Ω

8Ω

1&2

16Ω

Removable IEC

Power Receptacle

Channel Status

LEDs

Attenuators

Output Mode

Selector Switches

Line Input

Speaker Output

Connectors

Remote Ports

Figure 13. XPA U 1004 SB and XPA U 2002 SB Rear Panels

Removable IEC Power Receptacle — Connect the supplied IEC power cord here

for power input (100 VAC to 240 VAC, 50-60 Hz) to the internal power supply. The

connector can be replaced by a Flexible Conduit Adapter Kit (see Flexible Conduit

Adapter Kit Installation on page8).

Channel Status LEDs — The 1004 SB has four double-stacked LEDs, while the 2002

SB has two double-stacked LEDs.

The top red LEDs indicate limiter/protect status, and the bottom green LEDs indicate

signal status. These LEDs share the same function as the front panel LEDs.

Attenuators — Use a small screwdriver to adjust the gain structure for a corresponding

channel. Each channel has its own potentiometer, ranging from ∞ (full attenuation) to 0

dB (no attenuation)

To adjust the attenuation level on the amplifier, perform the following:

When volume is controlled at the source:

1. If connecting to a source device with volume control (variable output), ensure the

volume on the source device is set to its lowest point, then adjust the attenuation of

the amplifier fully counterclockwise.

La page charge ...

Extron electronics XPA Ultra Series Manuel utilisateur

Marque: Extron electronics

Modèle: XPA Ultra Series

Catégorie: Matériel musical

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Extron electronics XPA Ultra Series User manual

Extron electronics XPA Ultra Series Manuel utilisateur

Ce manuel convient également à

Extron electronics XPA Ultra Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents