TEAC CR-H700DAB Le manuel du propriétaire

CQX1A1 635Y

Z

CR-H700DAB

ENGLISH FRANÇAIS ESPAÑOL

DEUTSCH ITALIANO

DAB/AM/FM Stereo CD Receiver

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

2

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of uninsulated “dangerous voltage” within

the product’s enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

10) Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand,

tripod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

IMPORTANT SAFETY

INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

< Do not expose this apparatus to drips or splashes.

< Do not place any objects filled with liquids, such as

vases, on the apparatus.

< Do not install this apparatus in a confined space such

as a bookcase or similar unit.

< The apparatus draws nominal non-operating power

from the AC outlet with its POWER or STANDBY/ON

switch not in the ON position.

< The apparatus should be located close enough to the

AC outlet so that you can easily grasp the power cord

plug at any time.

< The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

< Products with Class Ι construction are equipped with a

power supply cord that has a 3-prong grounding plug.

The cord of such a product must be plugged into an

AC outlet that has a protective grounding connection.

< If the product uses batteries (including a battery pack

or installed batteries), they should not be exposed to

sunshine, fire or excessive heat.

< CAUTION for products that use replaceable lithium

batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace

only with the same or equivalent type.

< Caution should be taken when using earphones or

headphones with the product because excessive

sound pressure (volume) from earphones or

headphones can cause hearing loss.

3

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

Supply of this product does not convey a license nor imply

any right to distribute MPEG Layer-3 compliant content

created with this product in revenue-generating broadcast

systems (terrestrial, satellite, cable and/or other distribution

channels), streaming applications (via Internet, intranets and/

or other networks), other content distribution systems (pay-

audio or audio-on-demand applications and the like) or

on physical media (compact discs, digital versatile discs,

semiconductor chips, hard drives, memory cards and the like).

An independent license for such use is required. For details,

please visit http://mp3licensing.com.

Wi-Fi is a registered mark of the Wi-Fi Alliance.

The Wi-Fi CERTIFIED Logo is a certification mark of the

Wi-Fi Alliance.

This product is protected by certain intellectual property

rights of Microsoft. Use or distribution of such technology

outside of this product is prohibited without a license from

Microsoft.

Windows, Windows Vista, Windows 7 and Windows Media

are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean

that an electronic accessory has been designed to connect

specifically to iPod, iPhone, or iPad, respectively, and has

been certified by the developer to meet Apple performance

standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod, iPhone, or

iPad may affect wireless performance.

Apple, AirPlay, the AirPlay logo, iPad, iPhone, iPod, iPod classic,

iPod nano, iPod shuffle, iPod touch and iTunes are trademarks

of Apple Inc., registered in the U.S. and other countries.

Other company names, product names and logos in this

document are the trademarks or registered trademarks of

their respective owners.

Copyrights or licenses regarding open sources are shown at

the end of this manual.

CAUTION

< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS

TO EXPOSE THE ELECTRONICS. NO USER SERVICEABLE

PARTS ARE WITHIN!

< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS

PRODUCT, CONTACT TEAC FOR A SERVICE REFERRAL.

DO NOT USE THE PRODUCT UNTIL IT HAS BEEN

REPAIRED.

< USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

WARNING: TO PREVENT FIRE OR

SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

This product has been designed and manufactured

according to FDA regulations “title 21, CFR, chapter 1,

subchapter J, based on the Radiation Control for Health

and Safety Act of 1968“, and is classified as class 1 laser

product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted

inside of this product is completely confined in the

protective housings.

The label required in this regulation is shown as follows.

Optical pickup :

Type : EP-C101

Manufacturer : Ever Bright Technology and

Science Electronical Co.,Ltd

Laser output : Less than 1mW on the objective lens

Wavelength : 790±25nm

4

Before Use

Features of CR-H700DAB

< USB port for iPod/iPhone/USB devices

< Internet Radio (page 42)

< Airplay (page 45)

< Music Streaming (page 46)

Music Streaming is a function for using audio/visual

devices, computers, or other information home

appliances together in a network.

< Media Player (page 51)

CR-H700DAB offers you “Multi-room and Multi-Control-

Solution” by AirPlay, Music Streaming, and Media Player.

Read this before operations.

< When the unit is turned on, switching on the TV may

result in lines appearing on the TV screen, depending

on the condition of the electric waves of the TV

broadcast. This is not malfunction in the unit or the TV.

In this case, turn off the unit.

< As the unit may become warm during operation,

always leave sufficient space around the unit for

ventilation.

< The voltage supplied to the unit should match the

voltage as printed on the rear panel. If you are in any

doubt regarding this matter, consult an electrician.

< Choose the installation location of your unit carefully.

Avoid placing it in direct sunlight or close to a source

of heat. Also avoid locations subject to vibrations and

excessive dust, heat, cold or moisture.

< Do not place the unit on an amplifier/receiver.

< Do not open the cabinet as this might result in

damage to the circuitry or electrical shock. If a foreign

object should get into the set, contact your dealer or

service agency.

< When removing the power plug from the wall outlet,

always pull directly on the plug, never yank the cord.

< Do not attempt to clean the unit with chemical

solvents as this might damage the finish. Use a clean,

dry cloth.

< Keep this manual in a safe place for future reference.

< The operations are illustrated using the European

model for example in this manual.

DO NOT MOVE THE UNIT DURING PLAYBACK

During playback, the disc rotates at high speed. Do

NOT lift or move the unit during playback. Doing so

may damage the disc.

WHEN MOVING THIS UNIT

When changing places of installation or packing the

unit for moving, be sure to remove the disc and return

the disc table to its original position in the player.

Then, press the power switch to turn the power off,

and disconnect the power cord. Moving this unit with

the disc loaded may result in damage to this unit.

Contents

Thank you for choosing TEAC. Read this manual

carefully to get the best performance from this

unit.

Before Use .............................................4

Playable Discs/Files and iPod/iPhone/iPad Compatibility 5

Connecting Antennas (DAB) ............................7

Connecting Antennas (AM/FM) .........................8

Speaker Connections ...................................9

Connections ..........................................10

Part Names (main unit) ................................12

Part Names (remote control unit) ......................14

Remote Control Unit ..................................16

Basic Operation .......................................17

Disc Playback .........................................18

USB Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

General Playback (disc/USB) .......................... 20

Folder Search .........................................21

Programmed Playback ............................... 22

Shuffle Playback ......................................24

Repeat Playback ......................................24

Display .............................................. 25

Listening to iPod ..................................... 25

DAB Basic Operations ................................ 28

Using DAB Menu ..................................... 29

Changing Display Settings for DAB ................... 34

Listening to FM/AM ...................................35

Preset Tuning ........................................ 36

RDS .................................................. 38

PTY Search ............................................39

Initial Network Setup ..................................41

Listening to Internet Radio ............................42

Radio Portal ...........................................45

Using AirPlay ..........................................45

Using Music Streaming ...............................46

Setting up Media Player ...............................47

Listening to Media Player ..............................51

Network Configuration ................................52

Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Setting the Timer .................................... 54

Timer Operation ......................................55

Sleep Timer .......................................... 56

Listening to an External Source ....................... 56

Troubleshooting ......................................57

Specifications ........................................ 60

ENGLISH

5

Playable Discs:

M Conventional audio CDs bearing the COMPACT DISC

DIGITAL AUDIO logo on the label.

M Properly finalized CD-R and CD-RW discs

M MP3/WMA CDs

Note:

< Depending on the quality of the disc and/or the

condition of the recording, some CD-R/CD-RW discs

may not be playable.

< Copy-protected discs and other discs which do

not conform to the CD standard may not play back

correctly in this player. If you use such discs in this

unit, TEAC Corporation and its subsidiaries cannot be

responsible for any consequences or guarantee the

quality of reproduction. If you experience problems

with such non-standard discs, you should contact the

producers of the disc.

< Always place the disc on the disc tray with the label

side uppermost. (Compact discs can be played or

recorded only on one side.)

< To remove a disc from its storage case, press down on

the center of the case and lift the disc out, holding it

carefully by the edges.

< If the disc becomes dirty, wipe the surface radially

from the center hole outward towards the outer edge

with a soft and dry cloth.

< Never use such chemicals as record sprays, antistatic

sprays or fluid, or thinner to clean the discs. Such

chemicals will do irreparable damage to the disc’s

plastic surface.

< Discs should be returned to their cases after use to

avoid dust and scratches that could cause the laser

pickup to ”skip”.

< Do not expose discs to direct sunlight or high

humidity and temperature for extended periods. Long

exposure to high temperatures will warp the disc.

< Do not play any disc that is warped, deformed or

damaged. Playing such discs may cause irreparable

harm to the playing mechanisms.

< CD-R and CD-RW discs are more sensitive to the

effects of heat and ultraviolet rays than commercial

CDs. It is important that they are not stored in a

location where direct sunlight will fall on them, and

which is away from sources of heat such as radiators or

heat-generating electrical devices.

< While printable CD-R and CD-RW discs utilizing

modern printing technologies are generally

acceptable, older systems that use adhesives to

attach paper type labels to the disc surface are not

recommended.

< Do not stick papers or protective sheets on the discs

and do not use any protective coating spray.

< Use a soft oil-based felt-tipped pen to write the

information on the label side. Never use a ball-point

or hard-tipped pen, as this may cause damage to the

recorded side.

< Never use a stabilizer. Using commercially available CD

stabilizers with this unit will damage the mechanisms

and cause them to malfunction.

< Do not use irregular shape CDs (octagonal, heart

shaped, business card size, etc.). CDs of this sort can

damage the unit.

< If you are in any doubt as to the care and handling of a

CD-R/CD-RW disc, read the precautions supplied with

the disc, or contact the disc manufacturer directly.

Playable Discs/Files and iPod/iPhone/iPad Compatibility (1)

6

Playable Files:

< This unit can play various files recorded in various

external USB storage devices such as USB flash

memory, MP3 player or HDD.

USB storage devices must be formatted FAT 16 or FAT

32, but not NTFS.

< When more than 2000 files are recorded using the

USB memory, the unit might not be able to play them

correctly.

< File names should be alphanumeric characters. This

unit cannot display symbols and full-size or double-

byte characters (such as Japanese, Chinese, etc.)

correctly. Also, be sure to use the proper file extension.

< Audio encoded at 128 kbps should sound close to

regular audio CD quality. Although this player will play

lower bit-rate MP3 files, the sound quality becomes

noticeably worse at lower bit-rates.

The file formats that can be played back by each playback

source are as follows.

Format CD USB

Media Player

WiFi

Ethernet

cable

LPCM



– – –

WAV –

  

FLAC –

  

ALAC – –

 

MP3

  

OGG – –

 

WMA

  

AAC –

  

MP3

File extension: .mp3

Stream: MPEG-1/2 Layer III

Sampling Frequency: 8 to 48 kHz

Bit Rate: 8 to 320 kbps

LPCM (CD-DA)

Stream: LPCM

Sampling Frequency: 44.1 kHz

WAV

File extension: .wav

Stream: LPCM

Sampling Frequency: 8 to 48 kHz

ALAC

File extension: .m4a

Supported standard: Apple Lossless

Sampling Frequency: 44.1 kHz

FLAC

File extension: .flac

Stream: FLAC

Sampling Frequency: 8 to 48 kHz

Only 48kHz is supported with USB.

Ogg Vorbis

File extension: .ogg

Stream: Ogg

Sampling Frequency: 8 to 48 kHz

Bit Rate: 16 to 128 kbps

WMA

File extension: .asf/.wma

Stream: WMA2/7/8/9/10, WMA Pro, WMA Lossless

Sampling Frequency: 8 to 48 kHz

Bit Rate: 5 to 320 kbps

Note: WMA Pro and WMA Lossless formats are only

supported when the playback computer is using

Windows Media Player 12 or later. (Playback occurs

after transcoding.)

AAC

File ex tension: .m4a/. aac /.3gp/.3g2

Stream: MPEG-4 AAC/MPEG-4 HE AAC (AAC Plus v1/2)

Sampling Frequency: 32 to 96 kHz

Bit Rate: 16 to 320 kbps

iPod/iPhone/iPad Compatibility

This unit can be connected to and used with the

following iPod models.

iPod nano ( 2nd, 3rd, 4th, 5th, and 6th generation)

iPod touch (1st, 2nd, 3rd, and 4th generation)

iPhone 4, iPhone 3GS, iPhone 3G

iPad 2, iPad

< This unit cannot output video from a connected iPod/

iPhone/iPad.

< To connect an iPod/iPhone/iPad, use the USB cable

supplied with the iPod/iPhone/iPad.

Compatible iPod Software

In case your iPod will not work with the CR-H700DAB

or with the remote control unit, a software update

may solve the problem.

Visit the Apple website and download the latest iPod

software.

Playable Discs/Files and iPod/iPhone/iPad Compatibility (2)

ENGLISH

7

Connecting Antennas (DAB)

DAB Indoor Antenna

Connect the T-type DAB antenna to the DAB antenna

terminal. Extend the lead vertically and attach it to a

window frame or wall with thumbtacks or the like.

< You can adjust the antenna positioning for the best

reception by viewing the signal strength on the

display. See “Signal strength” in “Changing Display

Settings for DAB“ on page 34.

DAB Outdoor Antenna

In an area where DAB signals are weak, it will be

necessary to use an outdoor DAB antenna.

< It is possible to use a TV antenna or an FM antenna to

receive DAB signals. This may give a stronger signal

than a simple internal antenna.

You would need to change the plug on your TV/FM

antenna to an F type, and it may also be necessary to

use a signal booster to enhance the signal.

Multi-element

Dipole

8

FM Indoor Antenna

Connect the lead-type FM antenna to the FM 75Ω socket,

extend the lead and tune in your favourite station (see

page 35). Adjust the antenna in a suitable location like a

window frame or wall until the reception is best and then

affix the antenna in that position using thumb tacks, push

pins or any other suitable means.

FM Outdoor Antenna

In an area where FM signals are weak, it may be necessary

to use an FM outdoor antenna.

Generally, a 3-element antenna will be sufficient; if you

live in an area where the FM signals are particularly weak,

it may be necessary to use one with 5 or more elements.

< Disconnect the FM indoor antenna when using an

outdoor antenna.

AM Indoor Loop Antenna

The high-performance AM loop antenna provided with

this unit is sufficient for good reception in most areas.

To stand the loop antenna on a surface, fix the claw to

the slot in the antenna base.

Connect the loop antenna’s wires to the AM antenna

terminals.

Place the antenna on a shelf or hang it on a window

frame, etc., in the direction which gives the best

reception. Keep all other wires such as power cords,

speaker wires or interconnect wires as far away as

possible from the antenna.

< If the AM loop antenna provided does not deliver

sufficient reception (often due to being too far from

the transmitter or in a concrete building, etc.), it may

be necessary to use an AM outdoor antenna.

Use either a high quality commercially available AM

antenna or, if not available, an insulated wire more

than 5 m long. Strip one end, and connect this to the

terminal as shown.

The antenna wire should be fitted outdoors or indoors

near a window. For better reception, connect the GND

terminal to a reliable ground.

Note:

Even when using an AM outdoor antenna, do not

disconnect the AM loop antenna.

Connecting Antennas (AM/FM)

AM Outdoor

Antenna

Make sure to connect

the black wire to the

GND terminal.

ENGLISH

9

SUBWOOFER

SPEAKER

Speaker Connections

A

Speaker Connections

CR-H700DAB’s + (positive) terminals are red ( for the

right speaker) and white (for the left speaker.) The _

(negative) terminals are black.

The + side of the speaker cable is marked to make it

distinguishable from the negative side of the cable.

Connect this marked side to the red and white +

terminals and the unmarked side to the black _

terminals of CR-H700DAB and speakers.

CAUTION

< To avoid damaging the speakers with sudden high-

volume sound, be sure to switch the power off

before connecting the speakers.

< Check the impedance of your speakers. Connect

speakers with an impedance of 6 ohms or more.

< Prepare the speaker cables for connection by

stripping off approximately 10 mm (1/2 inch) or less

(no more as this could cause a short-circuit) of the

outer insulation. Twist the wires tightly together to

avoid tangles:

How to connect

1. Turn the terminal cap counter-clockwise to loosen it.

The speaker terminal caps cannot be fully removed

from the base.

2. Insert the wire into the terminal fully and turn the

terminal cap clockwise to securely connect it:

3. Make sure it is fastened firmly by pulling the cable

lightly.

For European customers

In accordance with European safety regulations, it

is not possible to connect banana plugs into the

speaker terminals on European models. The holes

into which banana plugs are inserted have been

covered with black caps. Connect the speakers

using spades or bare wires. If the black caps become

separated from the terminals, return them to their

original position.

B

SUBWOOFER OUT jack

Connect a commercially available powered

subwoofer.

B

A

LINE

IN

10

Connections

FE

D

A

LINE

OUT

LINE

IN

LRLR

B

C

Turntable

Cassette deck,

CD recorder, etc.

CAUTION

< Turn off the power of all the equipment before making connections.

< Read instructions of each component you intend to use with this unit.

< Be sure to insert each plug securely. To prevent hum and noise, do not bundle the connection cables with the power

cord or speaker cable.

ENGLISH

11

A

AC Power Cord

Plug this cord into an AC wall socket.

< Unplug the power cord when you are not going to

use the unit for long periods of time.

B

ETHERNET port

To use a wired Internet connection, connect the

ETHERNET port of this unit to the ethernet network

using a commercially available ethernet cable.

< If you connect or disconnect the ethernet cable

while the unit is turned on, turn the unit off and turn

it back on. See page 17 for how to turn the unit on or

off.

C

Wireless LAN antenna

If you can use a wireless LAN in your installation site,

the unit connects to the LAN using the wireless LAN

antenna. Stand the antenna up to use it.

D

AUX 1 jacks

These jacks transmit an analog 2-channel audio

signal. Connect the components using commercially

available RCA pin cables.

Make sure to connect the cables as follows:

white plug w white jack

(L: left channel)

red plug w red jack

(R:right channel)

White (L)

Red (R)

White (L)

Red (R)

If you want to use a recorder (ex. a cassette deck or

a CD recorder, etc.) with the CR-H700DAB, connect

the output jacks of the recorder to the AUX 1 IN jacks

of the CR-H700DAB, connect the input jacks of the

recorder to the AUX 1 OUT jacks of the CR-H700DAB.

< Be sure to insert each plug securely. To prevent

noise and humming, avoid bundling the signal

interconnection cables together with the AC power

cord or speaker cables.

E

PHONO jacks

Connect the turntable’s RCA pin cable to the PHONO

jacks.

Make sure to connect the cables as follows:

white plug w white jack

(L: left channel)

red plug w red jack

(R:right channel)

< Be sure to insert each plug securely. To prevent

noise and humming, avoid bundling the signal

interconnection cables together with the AC power

cord or speaker cables.

< Moving Magnet (MM) cartridges can be used with

this unit.

F

SIGNAL GND

Connect the ground lead of the turntable to this

terminal.

< This is not a safety earth.

< If the turntable’s ground lead is not connected to

this terminal, hum noise may be heard.

12

Part Names (main unit)

A

B

E

C

D

F G H I J NMK L

ENGLISH

13

A

MULTI JOG

In TUNER mode, use this knob to tune in stations or

select the preset stations.

In iPod mode, use this knob to scroll up and down the

menu.

In CD/USB mode, use this knob for the following

purposes:

- to skip tracks/files during playback

- CD only: in the stop/pause mode, to select a track/

file to play (press the y/J button to start playback)

- USB only: to select a folder or a file to play (press the

y/J button or ENTER button to start playback)

After pressing the TIME SET button, use this knob to

specify the time to turn on/off the unit or to select the

source to play.

After pressing the TONE button, use this knob to

adjust the bass or treble.

B

Remote sensor

When operating the remote control unit, point it

towards the remote sensor.

C

Display

D

VOLUME

Turn this knob to adjust the volume.

< The volume level is memorized even if the unit turns

off.

E

Standby/On ( )

Press this button to turn the unit on or off. The

standby indicator turns orange when the unit is on

standby. When the unit is turned on, the indicator

turns from orange to blue.

< When the unit has not received a signal for over 1

hour, it turns off automatically (Auto power off

function).

F

PHONES

For private listening, insert the headphones plug

into this jack, and adjust the volume by turning the

VOLUME knob.

G

AUX 2 IN

Connect equipment such as a portable audio player

using a 3.5 mm stereo mini plug cable.

H

USB port

Connect an iPod or external USB storage device.

I

SOURCE

Use this button to select a listening source.

J

MENU/FM MODE

Use this button to go back to a previous menu of your

iPod. This button is equivalent to the MENU button on

your iPod.

While listening to the Internet Radio or Media Player,

use this button to switch between the Internet

Radio/Media Player mode and the setup menu of the

network.

In FM mode, use this button to select stereo or

monaural.

In DAB mode, use this button to open menus.

K

Skip (.//)

In CD/USB mode, use these buttons for the following

purposes:

- to skip tracks/files during playback

- in the stop/pause mode, to select a track/file to play

(press the y/J button to start playback)

- in the pause mode, to start playing back a file (USB

only)

- to move to the folder in the next/previous layer

when a folder is selected (USB only)

In iPod mode, use these buttons to skip songs during

playback or in pause mode of the iPod.

When performing settings, use the .button to

return to the previous menu.

L

TUNING MODE, ENTER, Open/Close (L)

In FM or AM mode, use this button to select the

tuning mode.

Use this button to set the time while setting the timer

or the clock.

While listening to the Internet Radio or Media Player,

use this button to select a station, directory, or file to

play.

In iPod mode, use this button to confirm selection in

menus.

In USB mode, use this button to select a directory or

file to play.

In CD mode, use this button to open and close the

disc tray.

M

INFO/RDS, Stop (H)

In FM mode, use this button to select an RDS mode.

In DAB mode or while listening to the Internet Radio

or Media Player, use this button to change the

information on the second line of the display.

In USB/CD mode, use this button to stop playback.

N

BAND, Play/Pause (y/J)

Use this button to select FM, AM or DAB.

In USB/iPod mode, use this button to start or pause

playback of the iPod or USB.

In CD mode, use this button to start or pause playback

of the CD.

14

a

j

w

m

l

k

b

c

d

o

n

e

f

g

h

q

v

s

u

r

t

i

p

a

STANDBY/ON

Press this button to turn the unit on or standby.

When the unit is on standby, the Standby/On indicator

lights orange. When the unit is turned on, the

indicator turns from orange to blue.

b

TUNER, CD, iPod/USB, AUX 1/2, PHONO

Use these buttons to select a source.

c

TIME SET

Use this button to adjust the clock and to set a timer

(to specify the current time, the time to turn on/off the

unit, or to select the source to play).

d

TONE

Use this button to adjust the bass, treble, or sound

balance together with the scroll button. Use ˙ or ¥

to adjust the bass or treble and . or / to adjust

the sound balance.

e

TIMER

Use this button to select the timer function (“Timer

Daily”, “Timer Once”, or “Timer Off”).

f

FM MODE

In FM mode, use this button to select stereo or

monaural.

g

REPEAT 1/ALL

In USB/iPod mode, use this button to set the repeat

playback of the iPod or USB.

In CD mode, use this button to set the repeat playback

of the CD.

h

SHUFFLE

In USB/iPod mode, use this button to start shuffle

playback of the iPod or USB.

In CD mode, use this button to start shuffle playback

of the CD.

i

Stop (H)

In USB mode, use this button to stop playback of the

USB.

In CD mode, use this button to stop playback of the

CD.

Part Names (remote control unit)

ENGLISH

15

j

PROGRAM

In CD mode, use this button to enter the programme

mode of the CD.

In programme mode, use this button to enter the

selection.

In TUNER mode, use this button to preset stations.

k

Play/Pause (y/J)

In USB/iPod mode, use this button to start or pause

playback of the iPod or USB.

In CD mode, use this button to start or pause playback

of the CD.

l

MUTING

Use this button to mute the sound.

m

MENU

Use this button to go back to previous menu of iPod.

This button is equivalent to the MENU button on your

iPod.

While listening to the Internet Radio or Media Player,

use this button to switch between the Internet

Radio/Media Player mode and the setup menu of the

network.

n

ENTER

Use this button to set the time while setting the timer

or the clock.

While listening to the Internet Radio or Media Player,

use this button to select a station, directory, or file to

play.

o

Skip (.//)

In CD/USB mode, use these buttons for the following

purposes:

- to skip tracks/files during playback

- in the stop/pause mode, to select a track/file to play

(press the y/J button to start playback)

- in the pause mode, to start playing back a file (USB

only)

- to move to the folder in the next/previous layer

when a folder is selected (USB only)

In iPod mode, use these buttons to skip songs during

playback or in pause mode of the iPod.

Use these buttons to adjust the bass or treble.

p

Eject (L)

Use this button to open/close the disc tray.

q

DIMMER

Use this button to dim the display.

r

SLEEP

Use this button to set sleep timer.

s

INFO/RDS

In FM mode, use this button to select an RDS mode.

In DAB mode or while listening to the Internet Radio

or Media Player, use this button to change the

information on the second line of the display.

t

DISPLAY

Use this button to change what information is

displayed during CD/USB playback.

u

CLEAR

Use this button to clear tracks/files in programme

mode.

v

VOLUME

Use these buttons to adjust the volume level.

w

Scroll (˙/¥)

In USB/iPod mode, use these buttons to select a folder

or file of USB.

Or use these buttons to scroll the setup menu or the

menu of iPod.

After pressing the TONE button, these buttons are

used to adjust the bass or treble.

16

Remote Control Unit

The provided remote control unit allows the unit to be

operated from a distance.

When operating the remote control unit, point it towards

the remote sensor on the front panel of the unit.

< Even if the remote control unit is operated within the

effective range, remote control operation may be

impossible if there are any obstacles between the unit

and the remote control unit.

< If the remote control unit is operated near other

appliances which generate infrared rays, or if other

remote control devices using infrared rays are used

near the unit, it may operate incorrectly.

Conversely, the other appliances may operate

incorrectly.

Battery Installation

1. Remove the battery compartment cover.

2. Insert two “AAA” dry batteries. Make sure that the

batteries are inserted with their positive “+” and

negative “_” poles positioned correctly.

3. Close the cover.

Battery Replacement

If the distance required between the remote control unit

and main unit decreases, the batteries are exhausted. In

this case replace the batteries with new ones.

< For more information about collection of batteries,

please contact your local municipality, your waste

disposal service or the point of sale where you

purchased the items.

Precautions Concerning Batteries

< Be sure to insert the batteries with positive “+” and

negative “_” polarities positioned correctly.

< Use batteries of the same type. Never use different

types of batteries together.

< When the remote control unit is not to be used for a

long time (more than a month), remove the batteries

from the remote control unit to prevent them from

leaking.

< If the batteries leak, wipe away the liquid inside the

battery compartment and replace the batteries with

new ones.

< Do not use any other batteries not specified. Do not

mix new batteries with old ones or use different types

of batteries together.

< Do not heat or disassemble batteries and never throw

them in the fire or water.

< Do not carry or store batteries with other metallic

objects. The battery may short circuit, leak or explode.

< Never recharge a battery unless it is a verified

rechargeable type.

ENGLISH

17

Basic Operation (1)

A

B

C

A

How to turn the unit on or off

Press the button to turn the unit on or off.

The Standby/On indicator turns blue when the unit is

turned on.

< If no operation is done for more than an hour, the unit

turns off automatically (Auto Power Off).

However, when “On” is selected for “Network standby

setting” (page 53), this function is not available. (The

default setting is “Off”.)

< When you turn on the unit, the selected source is the

same as the one selected the last time the unit was

turned off.

In CD/iPod mode, when you turn off the unit during

playback of a track/file, the track/file will be played

back automatically when you next turn on the unit.

B

How to select source

Every time the SOURCE button is pressed, the mode is

changed as follows:

TUNER USB/iPod PHONO

CD AUX2 AUX1

Or press the TUNER, iPod/USB, PHONO, AUX 1/2 or CD

button on the remote control unit to select the source

directly.

When TUNER is selected as the source, pressing the

TUNER button on the remote control unit, or the

BAND button on the unit repeatedly changes the

mode as follows:

Internet Radio

AMFM

Media Player

DAB

C

Adjust the volume

To protect the speakers from a sudden high-volume

sound, gradually turn up the volume to the required

level with the VOLUME knob.

Muting

To mute the sound temporarily, press the MUTING

button. To cancel muting, press the MUTING button

again or change the volume setting.

Dimmer

Press the DIMMER button to dim the display.

Press the button again to cancel the dimmer function.

< This function will be cancelled when the unit is turned

off.

Standby/On indicator

18

Listening through headphones

Insert the headphone plug into the PHONES jack,

and adjust the volume. The sound from speakers and

subwoofer will be cut off.

How to adjust the bass/treble sound

and sound balance

You can change the bass and treble sound between

“-10” to “+10”. You can also change the sound balance

between the left/right speakers (The setting value is

between L (Left) +6 to R (Right) +6).

Press the TONE button repeatedly to select BASS,

TREBLE, or BALANCE CENTER. And then press the

scroll buttons (˙/¥) to adjust the bass or treble, or

press the skip/scan buttons (.//) to adjust the

balance within 3 seconds.

You can use the MULTI JOG knob to adjust the bass or

treble.

Playable disc/files of this unit are as follows:

Discs: CD-DA/CD-R/CD-RW

Files: MP3/WMA

1

Press the button to turn the unit on.

The Standby/On indicator turns from orange to blue.

2

Press SOURCE button to select “CD.”

“No Disc“ will be displayed if no disc has been inserted.

3

Press the open/close button (L).

Standby/On indicator

Disc Playback

1

2

6

3 5

4

Basic Operation (2)

ENGLISH

19

4

Place a disc on the tray with the printed label

facing up.

< The disc must be loaded centrally into the disc tray. If

the disc is not correctly loaded, it may not be possible

to open the tray again once it has closed.

< Never place more than one disc on the tray.

< Do not stick labels or tapes on the disc.

< Do not use irregularly-shaped discs.

5

Press the open/close button (L) to close the

tray.

< Keep fingers clear of moving tray to avoid trapping

them.

< It takes a few seconds for the unit to load a disc. No

buttons will work during loading. Wait until the total

number of the tracks/files and the total play time of

the disc are displayed.

< “No Disc” will be displayed if no disc has been inserted.

Audio CD

The total number of the tracks and total play time of

the disc are displayed.

CD/Stop

T016 72:00

MP3/WMA disc

The total number of files on the disc is displayed.

CD/Stop

Total File 010

6

Press the play/pause button (y/J ) to start

playback.

Disc playback starts from the first track/file.

Audio CD

MP3/WMA disc

< MP3/WMA files recorded outside of folders are

automatically put in the “ROOT“ folder, and playback

starts from the first file of the ROOT folder.

< If there are folders that have no MP3/WMA file, this

unit skips them.

< During playback of MP3/WMA file, “title_artist_album“

is scrolled across the display.

< The unit stops automatically when playback of all the

tracks/files has finished.

< If you load a disc, and then press the play/pause

button (y/J) (or the SHUFFLE button of the remote

control unit) without having first closed the disc tray,

the disc tray closes and playback starts.

CD/Play

T003 00:42 MP3

CD/Play

T003 00:42

current file number

current track number elapsed time of the current track

20

A

To stop playback

Press the stop button (H) to stop playback.

To start playback again, press the play/pause button

(y/J).

Playback starts from the first track/file.

B

To suspend playback temporarily (pause mode)

Press the play/pause button (y/J) during playback.

Playback stops at the current position.

To resume playback, press the play/pause button

(y/J).

C

To eject the disc

When the open/close button (L) is pressed, playback

stops and the tray will open.

After the disc is ejected, close the tray by pressing the

open/close button (L).

< When CD is selected as the source, you can eject the

disc.

1

3

You can play MP3/WMA files by connecting various

external USB storage devices such as USB flash memory.

For details on playable files, see “Playable Files” on page 6.

1

Press the SOURCE button repeatedly to select

“USB/iPod”.

“Not Connected” will be displayed if no USB device is

connected.

2

Connect the external USB storage device to the

unit.

When an HDD device is connected to this unit, it may

take several minutes to display the number of files.

3

Press the play/pause button (y/J).

AC B

D

USB Playback

General Playback (disc/USB)

La page charge ...

TEAC CR-H700DAB Le manuel du propriétaire

TEAC CR-H700DAB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents