Tripp Lite OMNIX350HG Le manuel du propriétaire

1

Owner’s Manual

SMX & OMNIX

Medical Grade UPS Systems

Models:

Important Safety Instructions 2

Package Contents 5

Quick Installation 6

Basic Operation 8

Guidance and Manufacturer’s Declaration 14

Storage & Service 16

Regulatory Compliance 17

Español 18

Français 35

Deutsch 52

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

OMNIX350HG

(Series Number: AGOM6832)

SMX700HG

(Series Number: AGSM6833)

SMX1200XLHG

(Series Number: AGSM6834)

18-09-528-9333A2.indb 1 10/16/2018 10:33:26 AM

2

Important Safety Instructions

Statement of Intended Use

Tripp Lite Medical-Grade UPS Systems are intended to support and protect non-medical computer

equipment and medical devices that require leakage current reduction, surge protection, voltage

regulation, line noise ﬁltering and battery backup during power outages and generator testing, both

inside and outside patient care areas. Tripp Lite’s Medical-Grade UPS Systems come with hospital-

grade plugs and receptacles that reduce leakage to below 100μA.

Product Information

OMNIX350HG SMX700HG SMX1200XLHG

AC Input Voltage 230V 230V 230V

Input Amp(s) 1.78 4 5

Output Amp(s) 1.5 2 3.3

Rated Power (VA/Watts) 350VA, 225W 700VA, 450W 1000VA, 750W

Frequency 50/60 Hz 50/60 Hz 50/60 Hz

No. of Phases Single Single Single

Class Type Class I Class I Class I

Plug/Connector Type Inlet C14 with dongle Inlet C14 with dongle Inlet C14 with dongle

Operation Continuous Continuous Continuous

AC Input Protection (Qty/type/rating) Input breaker (2 x 3A)

thermal

Input breaker (2 x 5A)

thermal

Input breaker (2 x 6A)

thermal

Max Leakage Current (uA) Less than 100uA Less than 100uA Less than 100uA

Weight 11.5 kg 19.1 kg 20.6 kg

Known Contraindication None None None

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation,

operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings may affect

your warranty.

Note: Your UPS incorporates overcurrent protection in both the L1 and L2 input conductors.

UPS Location Warnings

Relevant Symbols

Denotes that information in the manual should be reviewed before use.

Used to signal as a warning that a statement is particularly important and could pose a safety

risk.

Warning-Dangerous Voltage No sitting

Denotes general warning sign No stepping on surface

Refer to Instruction Manual/Booklet No pushing

18-09-528-9333A2.indb 2 10/16/2018 10:33:26 AM

3

Important Safety Instructions

• Do not use this equipment within oxygen-enriched atmospheres, or within 0.3 m of a point at

which an oxygen-enriched atmosphere is intentionally vented.

• Use caution when lifting UPS. Because of the considerable weight of all UPS systems, at least

two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the UPS should be used in a location that meets the following conditions:

Temperature: 0 to 40° C; Humidity: 0 to 95% (non-condensing);

Elevation: <2,000 m above sea level; Pressure: >95kPa

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its vents

or fan openings.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner

will seriously inhibit the unit’s internal cooling, eventually causing product damage not covered

under warranty.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even when

the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug in a

way that would eliminate the UPS’s connection to ground. Do not use adapters that eliminate the

UPS’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must provide

ﬁltered, frequency-regulated output. Connecting your UPS to a generator will void its Ultimate

Lifetime Insurance.

• To remove the UPS from the supply mains, the appliance inlet serves as a disconnect device.

• Once connected, do not limit access to the input plug. The plug must be accessible to be used as

a means of disconnection.

CAUTION: Do not remove cover for 5 minutes after disconnecting all sources of

supply. Risk of electric shock—hazardous live parts inside. Do not remove cover.

No user serviceable parts inside. Refer servicing to qualiﬁed service personnel.

This UPS receives power from more DC sources; disconnection of the AC and DC

source is required to de-energize the unit before servicing.

CAUTION: To ensure proper grounding with supply mains power, the input cord must

be connected with an approved country-speciﬁc plug with a protective earth ground

connection.

CAUTION: If this product is operated on battery (not connected to mains power),

adequate safeguards should be employed to protect against accidental contact

with AC power conductors.

CAUTION: Do not exceed total rated output.

WARNING: No modiﬁcation of this equipment is allowed.

18-09-528-9333A2.indb 3 10/16/2018 10:33:26 AM

4

Important Safety Instructions

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or failure of

a Tripp Lite UPS System could cause failure or signiﬁcantly alter the performance of a life-support

device.

• The AC output cord length should not exceed 33 ft. (10 m).

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

CAUTION: The unit is for exclusive interconnection with IEC 60601-1 certiﬁed

equipment in the patient environment and IEC 60950-1 certiﬁed equipment outside

of the patient environment. Do not contact SIP/SOP (such as the USB port, RS232

port, etc.) and the patient at the same time.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a ﬁre. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Battery replacement should be performed only by authorized

service personnel using the same number and type of batteries (sealed Lead-Acid). The batteries

are recyclable. Refer to your local codes for disposal requirements. Tripp Lite offers a complete

line of UPS System Replacement Battery Cartridges (R.B.C.). Visit Tripp Lite on the Web at

www.tripplite.com to locate the speciﬁc replacement battery for your UPS.

• During hot-swap battery replacement, the UPS will not provide backup power in the event of a

blackout or other power interruptions.

• Do not operate UPS without batteries.

• If your UPS is equipped with an external battery connector, only connect Tripp Lite external battery

packs of the appropriate voltage.

• If your UPS is not equipped with an external battery connector, do not attempt to add external

batteries.

Replacement Battery

MODEL

BATTERY

AND QUANTITY

NOMINAL VOLTAGE

OF BATTERY STRING BATTERY PACK NO.

OMNIX350HG (AGOM6832) LEAD-ACID

6V, 2 PCS

12V, 12AH RBC52

SMX700HG (AGSM6833) LEAD-ACID

12V, 3 PCS

36V, 9AH RBC53

SMX1200XLHG (AGSM6834) LEAD-ACID

12V, 3 PCS

36V, 9AH RBC53

Maintenance:

• Other than battery replacement, the UPS does not require maintenance. There are no user

serviceable parts inside. Battery replacement should only be performed by qualiﬁed service

personnel.

Cleaning/Disinfecting:

• Before cleaning or disinfecting, the UPS should be turned off and unplugged.

• For cleaning the UPS, only a damp cloth should be used.

• For disinfecting the USP, a damp cloth wetted with isopropyl alcohol may be used. No other

cleaning agent should be used.

18-09-528-9333A2.indb 4 10/16/2018 10:33:26 AM

5

Important Safety Instructions

Package Contents

UPS and Battery Disposal

• Always comply with local ordinances for proper methods of recycling and disposal of electronic

equipment.

• When purchasing a new UPS from Tripp Lite, you may send an old UPS back for recycling on a

one-for-one, like-for-like basis. The new equipment should also be sent back to Tripp Lite when it

ultimately becomes waste.

• Batteries can present risk of electric shock, burn and ﬁre if not disposed of properly.

SMX1200XLHG

• 1.8 m USB Cable

• 1.8 m DB9 Cable

• Owner’s Manual

SMX700HG

• 1.8 m USB Cable

• 1.8 m DB9 Cable

• Owner’s Manual

OMNIX350HG

• 1.8 m USB Cable

• 1.8 m RJ11 Cable

• Owner’s Manual

18-09-528-9333A2.indb 5 10/16/2018 10:33:26 AM

6

Quick Installation

1

For All Models—Plug your UPS into a

3-wire grounded, 230V AC 50/60 Hz utility

outlet.

For SMX Models Only:

After you plug the UPS into a live AC outlet, the UPS will

automatically charge its batteries, but will not supply power

to its outlets until it is turned ON (see Step 3 below). The

BATTERY CHARGE LED will be the only LED illuminated.

For OMNIX Models Only:

Your UPS will run a self-test after it is plugged in. See Basic

Operation to understand the results of its self-test.

2

For All Models—Plug your equipment into

the UPS.*

* You will overload the UPS if the total VA ratings for all the

equipment you connect exceeds the UPS’s Output Capacity (see

Speciﬁcations). To ﬁnd your equipment’s VA ratings, look on their

nameplates. If the equipment is listed in amps, multiply the number

of amps by 230 to determine VA. (Example: 1 amp × 230 V = 230

VA). If you are unsure if you have overloaded the UPS’s outlets, see

“OUTPUT LOAD LEVEL” LED description.

Note: UPS system will function properly upon initial startup; however,

maximum runtime for the unit’s battery will only be accessible after it

has been charged for 24 hours.

3

For SMX Models Only—Turn the UPS ON.

Press and hold the “POWER” button for one second. The

alarm will beep once brieﬂy after one second has passed.

Release the button.

For OMNIX Models Only—Select UPS

Operating Mode.*

Press the UPS/STANDBY button to toggle your UPS between

the UPS (“POWER” LED lit) and the STANDBY (“POWER” LED

ﬂashing) modes. Choose the operating mode based on your

location:

Western Europe:

• Leave the UPS in the UPS mode at all times.

All Other Countries:

• Put the UPS in the STANDBY mode when you are not

using connected equipment.

(WARNING! When set to “STANDBY,” the UPS will not

provide battery backup during a blackout or brownout.)

• Put the UPS in the UPS mode when you are using

connected equipment.

* See Basic Operation section for a complete explanation of each mode.

NORM DELAY

1

2

3

18-09-528-9333A2.indb 6 10/16/2018 10:33:27 AM

7

Quick Installation

NORM DELAY

1

2

3

4

These connections are optional. Your UPS will function properly without these connections.

1

Serial Communications

(Select models only)

If your UPS has a DB9 port, you can connect it to the DB9

port of a computer with the included cable. Use with

Tripp Lite’s PowerAlert Software for automatic ﬁle saves

and safe shutdown in case of power failure. (See Basic

Operation Section.)

2

USB Communications

Connect the USB port of your UPS to the USB port of a

computer with the included cable. Use with Tripp Lite’s

PowerAlert Software for automatic ﬁle saves and safe

shutdown in case of power failure. (See Basic Operation

Section.)

3

Tel/DSL Protection

(Select Models Only)

Using telephone cords, connect your wall jack to the UPS

jack marked “LINE” (or “IN”) and your equipment to the

UPS jack marked “EQUIP” (or “OUT”). This will protect your

equipment from surges over the phone line, but you should

make sure that your equipment is also protected against

surges on the AC line.

4

External Batteries

(Select Models Only)

External batteries are only needed to extend runtime. Adding

external batteries will increase recharge time as well as

runtime. Complete installation and mounting instructions

for your battery pack appear in the battery pack’s owner’s

manual. Make sure that cables are fully inserted into

their connectors. Small sparks may result during battery

connection; this is normal.

18-09-528-9333A2.indb 7 10/16/2018 10:33:28 AM

8

Basic Operation

Buttons

For SMX Models Only—“POWER” Button:

• To turn the UPS ON: With the UPS plugged into a live AC wall outlet,* press

and hold the POWER button for one second.** Release the button. If utility

power is absent, you can “cold-start” the UPS (i.e.: turn it ON and supply

power for a limited time from its batteries***) by pressing and holding the

POWER button for about two seconds.**

• To turn the UPS OFF: With the UPS ON and receiving utility power, press and

hold the POWER button for one second.** Then unplug the UPS from the wall

outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS will automatically charge its batteries,

but will not supply power to its outlets until it is turned ON. ** The alarm will beep once

brieﬂy after the indicated interval has passed. *** Fully charged batteries are recommended.

For OMNIX Models Only—“UPS/STANDBY” Button:

Use the UPS/STANDBY button to do three things:

Switch your UPS’s Operating Mode: While your UPS is plugged into a live AC

outlet, press the UPS/STANDBY button and hold it until you hear a beep (about

2 seconds) to toggle between the following operating modes. Choose your

UPS’s operating mode based on the regional guidelines in Step 3 of the Quick

Installation section.

• UPS Mode: ENABLES battery backup. UPS Conditions: While receiving

adequate utility line power, the UPS supplies power to its AC receptacles and

charges its batteries; its “POWER” indicator light will be lit. If the utility line

power fails or becomes inadequate, the UPS will supply inverted AC power

to its receptacles if its batteries are sufﬁciently charged. Setting Advantages:

Provides battery backup during blackouts or brownouts.

• STANDBY Mode: DISABLES battery backup. UPS Conditions: While receiving

adequate utility line power, the UPS supplies power to its AC receptacles and

charges its batteries; the “POWER” indicator light will be ﬂashing. Setting

Advantages: Continues to charge the battery when power is present while

turning OFF the inverter to prevent battery depletion during power outages

when equipment is not in use.

Cold-Start Your UPS: You may “cold start” your UPS and use it as a stand-alone

power source when utility power is not present, providing that the UPS battery

is charged. To “cold start” your UPS, press and hold the UPS/STANDBY button

until you hear a beep (about 2 seconds), then release it. The “BATTERY CHARGE/

BATTERY POWER” indicator light will illuminate and AC power inverted from stored

battery power will be provided at the UPS receptacles.

Shut Down Your UPS: Press and hold the UPS/STANDBY button when AC

line power is absent (i.e. during a blackout, or when the UPS is unplugged) to

deactivate your UPS.

18-09-528-9333A2.indb 8 10/16/2018 10:33:28 AM

9

Basic Operation

For All Models—“MUTE/TEST” Button:

To Silence (or “Mute”) UPS Alarms: brieﬂy press and release the MUTE/TEST

button.*

To Run a Self-Test: With your UPS plugged in and turned ON, press and hold

the MUTE/TEST button for two seconds.* The alarm will beep once. Release the

button, and the UPS will perform a self-test. See “Results of a Self-Test” below.

Note: you can leave connected equipment on during a self-test. Your UPS, however, will not

perform a self-test if it is not turned ON (see “POWER” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove

safe electrical grounding and may introduce a damaging surge into your

network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and battery charge.** If the

“OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues to sound

after the test, the UPS’s outlets are overloaded. To clear the overload, unplug

some of your equipment and run the self-test repeatedly until the “OUTPUT

LOAD LEVEL” LED is no longer lit red and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease

supplying output power in the event of a blackout or severe brownout.

If the “BATTERY WARNING” LED remains lit and the alarm continues to sound

after the test, the UPS batteries need to be recharged or replaced. Allow the

UPS to recharge continuously for 12 hours, and repeat the self-test. If the

LED remains lit, contact Tripp Lite for service. If your UPS requires battery

replacement, visit www.tripplite.com/products/battery-ﬁnder to locate the

speciﬁc Tripp Lite replacement battery for your UPS.

* The alarm will beep once brieﬂy after the indicated interval has passed. ** SMX models’

operation during the self-test: the “POWER” LED will be ﬂashing and the “OUTPUT LOAD

LEVEL” and “BATTERY CHARGE” LEDs will be lit and the UPS alarm will sound. OMNIX

models’ operation during the self-test: all LEDs will be lit and the UPS alarm will sound.

For SMX Models Only—“MUTE/TEST” Button:

The UPS is shipped with the audible alarms muted by default. To re-enable the

audible alarms, press and hold the MUTE/TEST button until you hear a short

beep followed by a continuous beep; then release the button. To disable the

audible alarms, press and hold the MUTE/TEST button until you hear a short beep

followed by another short beep; then release the button.

18-09-528-9333A2.indb 9 10/16/2018 10:33:28 AM

10

Basic Operation

Indicator Lights

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

“POWER” LED

For SMX Models Only: This green LED lights continuously when the UPS is ON

and supplying connected equipment with AC power from a utility source. The LED

ﬂashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe brownout.

If the blackout or severe brownout is prolonged, you should save ﬁles and shut

down your equipment since internal battery power will eventually be depleted.

See “BATTERY CHARGE” LED description below.

For OMNIX Models Only: This green light will turn ON whenever your UPS is

receiving normal AC line power. It will ﬂash while the UPS is in CHARGE ONLY

mode to indicate that the UPS will not provide battery backup during a blackout

or brownout.

“VOLTAGE CORRECTION” LED (SMX Models Only): This green LED lights

continuously whenever the UPS is automatically correcting high or low AC voltage

on the utility line without the assistance of battery power. The UPS will also emit

a slight clicking noise. These are normal, automatic operations of the UPS. No

action is required on your part.

“OUTPUT LOAD LEVEL” LED:

For SMX Models Only: This multicolored LED indicates the approximate

electrical load of equipment connected to the UPS’s AC outlets. It will turn from

green (light load) to yellow (medium load) to red (overload). If the LED is red

(either illuminated continuously or ﬂashing), clear the overload immediately by

unplugging some of your equipment from the outlets until the LED changes from

red to yellow (or green) and the alarm is no longer sounding. CAUTION! Any

overload that is not corrected by the user immediately may cause the UPS

to shut down and cease supplying output power in the event of a blackout

or severe brownout.

For OMNIX Models Only: This red light will turn ON continuously when the UPS

is providing power from battery or after the UPS runs a self-test to indicate that

the UPS’s inverter is overloaded. If it lights up, immediately remove some of the

equipment connected to the UPS and run a self-test. CAUTION! Any overload

that is not corrected by the user immediately may cause the UPS to shut

down and cease supplying output power in the event of a blackout or

severe brownout.

18-09-528-9333A2.indb 10 10/16/2018 10:33:28 AM

11

Basic Operation

“BATTERY CHARGE / BATTERY POWER” LED:

For SMX Models Only: When the UPS is operating from utility power, this

multicolored LED indicates the approximate charge state of the UPS’s internal

batteries: red indicates the batteries are beginning to charge; yellow indicates

the batteries are roughly midway through charging; and green indicates the

batteries are fully charged. When the UPS is operating from battery power during

a blackout or severe brownout, this LED indicates the approximate amount of

energy (ultimately affecting runtime) that the UPS’s batteries will provide: red

indicates a low level of energy; yellow indicates a medium level of energy; and

green indicates a high level of energy. Since the runtime performance of all UPS

batteries will gradually deplete over time, it is recommended that you periodically

perform a self-test (see “MUTE/TEST” Button description) to determine the energy

level of your UPS batteries BEFORE a blackout or severe brownout occurs. During

a prolonged blackout or severe brownout, you should save ﬁles and shut down

your equipment since battery power will eventually be depleted. When the LED

turns red and an alarm sounds continuously, it indicates the UPS’s batteries are

nearly out of power and UPS shut down is imminent.

For OMNIX Models Only: This yellow LED will illuminate when your UPS is

providing your equipment with battery backup power.

“BATTERY WARNING” LED: This LED lights red and an alarm sounds

intermittently after you initiate a self-test (See “MUTE/TEST” Button description)

to indicate the UPS batteries need to be recharged or replaced. Allow the UPS to

recharge continuously for 12 hours, and repeat the self-test. If the LED continues

to light, contact Tripp Lite for service. If your UPS requires battery replacement,

visit www.tripplite.com/products/battery-ﬁnder to locate the speciﬁc Tripp Lite

replacement battery for your UPS.

18-09-528-9333A2.indb 11 10/16/2018 10:33:29 AM

12

Basic Operation

Other UPS Features

AC Receptacles: The receptacles provide your connected equipment with AC

line power during normal operation and battery power during blackouts and

brownouts. They also protect your equipment against damaging surges and line

noise.

Tel/DSL Protection Jacks (Select Models Only): These jacks protect connected

equipment against surges travelling over the modem/fax or telephone line.

Connecting your equipment to these jacks is optional. Your UPS will still work

properly without this connection.

USB or DB9 Communication Port: These ports can connect your UPS to any

computer for automatic ﬁle saves and unattended shutdown in the event of a

power failure. Use with Tripp Lite’s PowerAlert Software and appropriate USB

or DB9 cable. A PowerAlert CD and USB or DB9 cable may be included with

your UPS; if so, insert the CD into the CD tray of your computer and follow the

installation instructions. If PowerAlert Software and the appropriate cable did

not come with your UPS, you can obtain the software FREE via the Web at

www.tripplite.com. Any user-supplied DB9 pass-through or USB cable may then

be used to connect your UPS to your computer.

Note: This connection is optional. The UPS will work properly without this connection.

Battery Replacement Door: Under normal conditions, the original battery in

your UPS will last several years. Battery replacement should be performed only

by qualiﬁed service personnel. Refer to “Battery Warnings” in the Safety section.

Should your UPS require battery replacement, visit Tripp Lite on the Web at

www.tripplite.com/products/battery-ﬁnder to locate the speciﬁc replacement

battery for your UPS.

External Battery Connector (Select Models Only): Use to connect one or

more Tripp Lite battery packs for additional runtime. Refer to Speciﬁcations and/

or the label next to the connector to determine the appropriate variety of battery

pack to use. Refer to the battery pack instruction manual for complete installation

information and important safety warnings.

Input Breakers: Protects your electrical circuit from overcurrent draw from the

UPS load. If breaker trips, remove some of the load, then reset it by pressing the

breaker in.

Equipotential Connection: Use this to connect any equipment that requires a

chassis ground.

18-09-528-9333A2.indb 12 10/16/2018 10:33:30 AM

13

Basic Operation

NORM DELAY

Power Sensitivity Adjustment: This dial is normally set fully counterclockwise,

which enables the UPS to protect against waveform distortions in its AC input.

When such distortion occurs, the UPS will normally switch to providing PWM

sine wave power from its battery reserves for as long as the distortion is present.

In areas with poor utility power or where the UPS’s input power comes from a

backup generator, chronic waveform distortion could cause the UPS to switch

to battery too frequently, draining its battery reserves. You may be able to

reduce how often your UPS switches to battery due to waveform distortion by

experimenting with different settings for this dial. As the dial is turned clockwise,

the UPS becomes more tolerant of variations in its input power’s AC waveform.

Note: The further the dial is adjusted clockwise, the greater the degree of waveform

distortion the UPS will allow to pass to connected equipment. When experimenting with

different settings for this dial, operate connected equipment in a safe test mode so that the

effect on the equipment of any waveform distortions in the UPS’s output can be evaluated

without disrupting critical operations.

18-09-528-9333A2.indb 13 10/16/2018 10:33:30 AM

14

Guidance and Manufacturer’s Declaration

This equipment is suitable for hospitals except for near active HF SURGICAL EQUIPMENT and the RF

shielded room of an ME SYSTEM.

WARNING: Use of this equipment adjacent to or stacked with other equipment should

be avoided because it could result in improper operation. If such use is necessary, this

equipment and the other equipment should be observed to verify that they are operating

normally.

WARNING: Use of accessories, transducers and cables other than those speciﬁed or

provided by the manufacturer of this equipment could result in increased electromagnetic

emissions or decreased electromagnetic immunity of this equipment and result in improper

operation.

Guidance and Manufacturer’s Declaration—Electromagnetic Emissions

This Medical-Grade UPS is intended for use in the electromagnetic environment speciﬁed below. The customer

or the user of this Medical-Grade UPS should assure that it is used in such an environment.

Standard Description Test Level/Limit Guidance

EN 55011:

2009+A1:2010

Radiated

Emissions

Models:

SMX700HG,

SMX1200XLHG

Class A Group 1,

30 - 1000 MHz

See notes 1 and 2

Model:

OMNIX350HG

Class B Group 1,

30 - 1000 MHz

See notes 1 and 3

EN 55011:

2009+A1:2010

Conducted

Emissions

Models:

SMX700HG,

SMX1200XLHG

Class A Group 1,

150 kHz – 30 MHz

See notes 1 and 2

Model:

OMNIX350HG

Class B Group 1,

150 kHz – 30 MHz

See notes 1 and 3

Notes:

1. Group 1: The Medical-Grade UPS uses RF energy only for its internal function. Therefore, its RF emissions are

very low and unlikely to cause any interference in nearby electronic equipment.

2. Class A: The Medical-Grade UPS is suitable for use in all establishments other than domestic and those

directly connected to the public low-voltage power supply network that supplies buildings used for domestic

purposes.

NOTE The EMISSIONS characteristics of this equipment make it suitable for use in industrial areas and

hospitals (CISPR 11 class A). If it is used in a residential environment (for which CISPR 11 class B is normally

required) this equipment might not offer adequate protection to radio-frequency communication services. The

user might need to take mitigation measures, such as relocating or re-orienting the equipment.

3. Class B: The Medical-Grade UPS is suitable for use in all establishments, including domestic and those

directly connected to the public low-voltage power supply network that supplies buildings used for domestic

purposes.

18-09-528-9333A2.indb 14 10/16/2018 10:33:30 AM

15

Guidance and Manufacturer’s Declaration

Guidance and Manufacturer’s Declaration—Electromagnetic Immunity

This Medical-Grade UPS is intended for use in the electromagnetic environment speciﬁed below. The customer

or the user of this Medical-Grade UPS should assure that it is used in such an environment.

Standard Description Test Level/Limit Guidance

EN 61000-4-2:2009 Electrostatic

Discharge

Immunity

±15 kV Air Discharge

±8 kV Contact Discharge, VCP, HCP

Floors should be wood,

concrete or ceramic tile.

If colors are covered with

synthetic material, the relative

humidity should be at least

30%.

EN 61000-4-3: 2006

+A1:2008+A2:2010

Radiated

Electromagnetic

Immunity

10V/m, 80 - 1000 Mhz

3V/m, 1 to 2.7 GHz at 80% 1kHz AM

Modulation

Mains power quality should be

that of a typical commercial or

hospital environment.

Radiated

Electromagnetic

and Proximity

Fields Immunity

RF wireless communication ﬁelds

on Spot Frequencies from Table 9 at

50%, Square wave Modulation 9 to

28 V/m,

EN 61000-3-2:2014 Power

Harmonics

230V, 50/60Hz

Class A Mains power quality should be

that of a typical commercial or

hospital environment.

EN 61000-3-3:2013 Voltage

Fluctuation 230V,

50Hz

Pst ≤ 1, dc ≤ 3.3%, dmax ≤ 6%,

d(t) ≤ 3.3% for 500ms

Mains power quality should be

that of a typical commercial or

hospital environment.

EN 61000-4-4:2012 Electrical Fast

Transient/Burst

Immunity

±2kV on AC Mains

±1 kV on SIP/SOP Ports

Mains power quality should be

that of a typical commercial or

hospital environment.

EN 61000-4-5:2006 Surge Immunity ±0.5 kV, ±1 kV, ±2kV CM Line-Gnd

±0.5 kV, ±1 kV, DM Line-Line

NA on SIP/SOP Ports

Mains power quality should be

that of a typical commercial or

hospital environment.

EN 61000-4-6:2013 Conducted

Immunity

6V rms, on ISM and Amateur bands,

3V rms, 0.15 - 80 MHz, AC Mains

and SIP/SOP Ports

Mains power quality should be

that of a typical commercial or

hospital environment.

EN 61000-4-8:2010 Power Frequency

Magnetic Field

Immunity

30A/m @ 50 Hz or 60 Hz

3 orthogonal orientations

Power frequency magnetic

ﬁelds should be at levels

characteristic of a typical

location in a typical

commercial or hospital

environment.

EN 61000-4-11:2004 Voltage

Dips, Short

Interruptions

and Voltage

Variations

Immunity

0%, 0.5 Cycles, 0%, 1 Cycle

70%, 30 Cycles, 0%, 300 Cycles

Mains power quality should be

that of a typical commercial or

hospital environment.

EN 61000-2-2:2004 Power Line

Harmonics and

Inter-Harmonics

Single sinusoidal source of 10V rms,

slowly varied from 140 to 360 Hz.

Mains power quality should be

that of a typical commercial or

hospital environment.

18-09-528-9333A2.indb 15 10/16/2018 10:33:30 AM

16

Storage & Service

Storage

For SMX Models Only: Before storing your UPS, turn it completely OFF: with the UPS ON and

receiving utility power, press and hold the POWER button for one second (an alarm will beep once

brieﬂy after the interval has passed); then, unplug the UPS from the wall outlet. CAUTION! Your

UPS has an internal power source. Its outlets may still deliver current, even after the UPS

is unplugged, until the UPS is completely turned OFF (deactivated). If you store your UPS for

an extended period of time, recharge the UPS batteries once every three months: plug the UPS into

a wall outlet; allow it to charge for 12 hours; and then unplug it and place it back in storage. Note:

after you plug the UPS in, it will automatically begin charging its batteries; however, it will not supply

power to its outlets (see Quick Installation section). If you leave your UPS batteries discharged for

an extended period of time, they will suffer a permanent loss of capacity.

For OMNIX Models Only: All connected equipment should be turned off, then disconnected from

the UPS to avoid battery drain. Unplug your UPS from its AC receptacle. CAUTION: Your UPS has

an internal power source. Its outlets may still deliver current after it is unplugged, until the

UPS is deactivated. To deactivate the UPS, press and hold its UPS/STANDBY button. Your UPS is

now ready for storage. If you plan on storing your UPS for an extended period of time, fully recharge

the UPS batteries once every three months by plugging the UPS into a live AC outlet and letting the

UPS charge for 12 hours. If you leave your UPS batteries discharged for an extended period of time,

they will suffer a permanent loss of capacity.

Permissible Storage and Transportation Conditions

Humidity 0-95% Non-Condensing

Temperature -15°C to 45°C

Elevation 0 to 15,240 m

Atmospheric Pressure >95 kPa

Service

A variety of Extended Warranty and On-Site Service Programs are available from Tripp Lite. For more

information on service, visit www.tripplite.com/support. Before returning your product for service,

follow these steps:

1. Review the installation and operation procedures in this manual to insure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product Returns link.

From here you can request a Returned Material Authorization (RMA) number, which is required

for service. This simple on-line form will ask for your unit’s model and serial numbers, along with

other general purchaser information. The RMA number, along with shipping instructions will be

emailed to you. Any damages (direct, indirect, special or consequential) to the product incurred

during shipment to Tripp Lite or an authorized Tripp Lite service center are not covered under

warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must have

transportation charges prepaid. Mark the RMA number on the outside of the package. If the

product is within its warranty period, enclose a copy of your sales receipt. Return the product for

service using an insured carrier to the address given to you when you request the RMA.

18-09-528-9333A2.indb 16 10/16/2018 10:33:30 AM

17

Regulatory Compliance

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been

assigned a unique series number. The series number can be found on the product nameplate label, along with

all required approval markings and information. When requesting compliance information for this product, always

refer to the series number. The series number should not be confused with the marking name or model number of

the product.

FCC RADIO/TV INTERFERENCE NOTICE: (FOR CLASS A MODELS)

Note: The equipment has been tested and found to comply with the limits for a class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when operated in a commercial environment. This equipment generates, uses and radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense. The user must use shielded cables and connectors

with this product. Any changes or modiﬁcations to this product not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

FCC RADIO/TV INTERFERENCE NOTICE: (FOR CLASS B MODELS)

Note: The equipment has been tested and found to comply with the limits for a class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connection the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced raido/TV technician for help.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when

customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis

(this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are sealed Lead-

Acid batteries. These batteries are highly recyclable. Please refer to your local codes for disposal

requirements.

Tripp Lite has a policy of continuous improvement. Product speciﬁcations are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-09-528-9333A2.indb 17 10/16/2018 10:33:30 AM

18

Manual de operación

SMX & OMNIX

Sistemas UPS de Grado Médico

Modelos:

OMNIX350HG

(Número de Serie: AGOM6832)

SMX700HG

(Número de Serie: AGSM6833)

SMX1200XLHG

(Número de Serie: AGSM6834)

Importantes instrucciones de seguridad 19

Contenido del Empaque 22

Instalación rápida 23

Operación básica 25

Orientación y Declaración del Fabricante 31

Almacenamiento y servicio 33

Declaraciones Regulatorias y de Seguridad 34

English 1

Français 35

Deutsch 52

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-09-528-9333A2.indb 18 10/16/2018 10:33:30 AM

19

Importantes instrucciones de seguridad

Declaración de Uso Indicado

Los Sistemas UPS de Grado Médico de Tripp Lite están diseñados para soportar y proteger equipo

de computación no médico y dispositivos médicos que requieran reducción de fuga de corriente,

protección contra sobretensiones, regulación de voltaje, ﬁltrado de ruido en la línea y respaldo por

batería durante interrupción en el servicio eléctrico y prueba del generador, ambos dentro y fuera de

áreas de atención a pacientes. Los Sistemas UPS de Grado Médico de Tripp Lite vienen con clavijas

y tomacorrientes de grado hospital que reducen la fuga a menos de 100µA.

Información del Producto

OMNIX350HG SMX700HG SMX1200XLHG

Voltaje de Entrada de CA 230V 230V 230V

Amperes de Entrada 1.78 4 5

Amperes de Salida 1.5 2 3.3

Potencia Especiﬁcada (VA/Watts) 350VA, 225W 700VA, 450W 1000VA, 750W

Frecuencia 50/60 Hz 50/60 Hz 50/60 Hz

No. de Fases Mono Mono Mono

Tipo de Clase Clase I Clase I Clase I

Tipo de Clavija/Conector Entrada C14 con llave

electrónica

Entrada C14 con llave

electrónica

Entrada C14 con llave

electrónica

Operación Continua Continua Continua

Protección de Entrada de CA

(Cant./Tipo/Especif.)

breaker térmico de

entrada (2 x 3A)

breaker térmico de

entrada (2 x 5A)

breaker térmico de

entrada (2 x 6A)

Corriente Máx de Fuga (µA) Menos de 100 µA Menos de 100 µA Menos de 100 µA

Peso 11,5 kg 19,1 kg 20,6 kg

Contraindicación Conocida Ninguna Ninguna Ninguna

CONSERVE ESTAS INSTRUCCIONES

Este manual contiene instrucciones importantes que deben seguirse durante la instalación,

operación y almacenamiento de todos los Sistemas UPS de Tripp Lite. La falta de observar estas

advertencias podría afectar su garantía.

Nota: Su UPS tiene incorporada protección contra sobrecorriente en las tomas de alimentación L1 y L2.

Advertencias de Ubicación del UPS

Símbolos Importantes

Signiﬁca que debe revisarse la información en el manual antes de usarlo.

Se usa para indicar como advertencia que un párrafo es particularmente importante y puede

representar un riesgo a la seguridad.

Advertencia-Voltaje Peligroso No sentarse

Denota un signo de advertencia general No pararse sobre la superﬁcie

Consulte el Manual / Folleto de Instrucciones No Empujar

18-09-528-9333A2.indb 19 10/16/2018 10:33:30 AM

20

Importantes instrucciones de seguridad continuación

• No use este equipo en atmósferas enriquecidas con oxígeno o a distancias inferiores a 0.3 m de

un punto en que se ventile deliberadamente una atmósfera enriquecida con oxígeno.

• Tenga cuidado al levantar el UPS. Debido al peso considerable de todos los sistemas UPS, deben

ayudar al menos dos personas para levantarlos e instalarlos.

• Instale su UPS en interiores, alejado de humedad o calor excesivos, polvo o luz solar directa.

• Para mejor desempeño, el UPS debe usarse en una ubicación que cumpla con las siguientes

condiciones: Temperatura: 0 a 40° C; Humedad: 0 a 95% (sin condensación);

Elevación: <2 000 m sobre el nivel del mar; Presión: >95kPa

• Deje espacio adecuado alrededor del UPS para una ventilación apropiada. No obstruya las

ventilaciones o aberturas de ventiladores.

• No instale la unidad con su panel frontal o posterior viendo hacia abajo (en cualquier ángulo).

El instalar de esta manera inhibirá seriamente el enfriamiento interno de la unidad, causando

eventualmente daño al producto no cubierto por la garantía.

Advertencias para la Conexión del UPS

• El UPS contiene su propia fuente de energía (batería). Las terminales de salida pueden estar

energizadas, aún cuando el UPS no esté conectado a una alimentación de CA.

• Conecte su UPS a un tomacorriente de CA conectado correctamente a tierra. No modiﬁque

la clavija del UPS en modo alguno que pueda eliminar la conexión a tierra del UPS. No use

adaptadores que eliminen la conexión a tierra del UPS.

• No enchufe su UPS en sí mismo; esto dañará al UPS y anulará su garantía.

• Si está conectando su UPS a un generador de CA activado por motor, el generador de

proporcionar una salida ﬁltrada y con frecuencia regulada. Conectar su UPS a un generador

anulará el Seguro Máximo de por Vida.

• Para retirar el UPS de la alimentación general, la alimentación del dispositivo sirve como

dispositivo de desconexión.

• Una vez conectado, no limite el acceso a la clavija de entrada. La clavija debe estar accesible

para usarla como medio de desconexión.

PRECAUCIÓN: No retire la cubierta durante 5 minutos después de desconectar

todas las fuentes de alimentación. Riesgo de electrocución—partes energizadas

peligrosas en el interior. No retire la cubierta. No hay en el interior partes a las que

el usuario pueda dar servicio. Remita el servicio a personal de servicio caliﬁcado.

Este UPS recibe energía de más fuentes de CD; se requiere la desconexión de la

fuente de CA y CD para desenergizar la unidad antes de darle serviicio.

PRECAUCIÓN: Para garantizar la correcta conexión a tierra con la alimentación

de energía de la red pública, el cable de entrada debe conectarse con una clavija

especíﬁca autorizada para el país con una conexión de protección a tierra.

PRECAUCIÓN: Si este producto está operado en respaldo por batería (no está

conectado a la energía de la red pública), deben emplearse las salvaguardas

adecuadas para protegerse contra un contacto accidental con conductores de

energía de CA.

PRECAUCIÓN: No exceda la salida total especiﬁcada.

ADVERTENCIA: No se permite ninguna modiﬁcación de este equipo.

18-09-528-9333A2.indb 20 10/16/2018 10:33:30 AM

La page est en cours de chargement...

Tripp Lite OMNIX350HG Le manuel du propriétaire

Ce manuel convient également à

Tripp Lite OMNIX350HG Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents