Winmate 7'' S-Series Guide de démarrage rapide

Please read these instructions carefully before using this product, and save this manual for future use

15” S-Series HMI

R15IB3S-PCC3-PoE

Quick Start Guide

V1.0

For more information on this and

other Winmate products, please

visit our website at:

www.winmate.com

Document Part Number: 9152111I100T

- 2 -

FCC Statement

This device complies with part 15 FCC rules.

Operation is subject to the following two

conditions:

 This device may not cause harmful

interference.

 This device must accept any interference

received including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the

limits for a class "B" digital device, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at him

own expense.

- 3 -

European Union

Electromagnetic Compatibility Directive

(2014/30/EU)

 EN55024: 2010/ A1: 2015

o IEC61000-4-2: 2009

o IEC61000-4-3: 2006+A1: 2007+A2: 2010

o IEC61000-4-4: 2012

o IEC61000-4-5: 2014

o IEC61000-4-6: 2014

o IEC61000-4-8: 2010

o IEC61000-4-11: 2004

 EN55032: 2012/AC:2013

 EN61000-3-2:2014

 EN61000-3-3:2013

Low Voltage Directive (2014/35/EU)

 EN 60950-1:2006/A11:2009/A1:2010/A12:2011/

A2:2013

This equipment is in conformity with the requirement of the

following EU legislations and harmonized standards. Product also

complies with the Council directions.

- 4 -

Copyright Notice

No part of this document may be reproduced, copied, translated, or

transmitted in any form or by any means, electronic or mechanical, for

any purpose, without the prior written permission of the original

manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of

their respective owners.

Disclaimer

Winmate Inc. reserve the right to make changes, without notice, to

any product, including circuits and/or software described or contained

in this manual in order to improve design and/or performance. We

assume no responsibility or liability for the use of the described

product(s) conveys no license or title under any patent, copyright, or

masks work rights to these products, and make no representations or

warranties that these products are free from patent, copyright, or

mask work right infringement, unless otherwise specified. Applications

that are described in this manual are for illustration purposes only. We

make no representation or guarantee that such application will be

suitable for the specified use without further testing or modification.

Warranty

Winmate Inc. warranty guarantees that each of its products will be

free from material and workmanship defects for a period of one year

from the invoice date. If the customer discovers a defect, we will, at

his/her option, repair or replace the defective product at no charge to

the customer, provide it is returned during the warranty period of one

year, with transportation charges prepaid. The returned product must

be properly packaged in its original packaging to obtain warranty

service. If the serial number and the product shipping data differ by

over 30 days, the in-warranty service will be made according to the

shipping date. In the serial numbers the third and fourth two digits

give the year of manufacture, and the fifth digit means the month (e.

g., with A for October, B for November and C for December).

For example, the serial number 1W16Axxxxxxxx means October of

year 2016.

- 5 -

Customer Service

We provide a service guide for any problem by the following steps:

First, visit the website of our distributor to find the update information

about the product. Second, contact with your distributor, sales

representative, or our customer service center for technical support if

you need additional assistance.

You may need the following information ready before you call:

 Product serial number

 Software (OS, version, application software, etc.)

 Description of complete problem

 The exact wording of any error messages

In addition, free technical support is available from our engineers

every business day. We are always ready to give advice on

application requirements or specific information on the installation and

operation of any of our products.

- 6 -

Safety Information

WARNING! / AVERTISSEMENT!

Always completely disconnect the power cord from your

chassis whenever you work with the hardware. Do not

make connections while the power is on. Sensitive

electronic components can be damaged by sudden power

surges. Only experienced electronics personnel should

open the PC chassis.

Toujours débrancher le cordon d’alimentation du chassis

lorsque vous travaillez sur celui-ci. Ne pas brancher de

connections lorsque l’alimentation est présente. Des

composantes électroniques sensibles peuvent être

endommagées par des sauts d’alimentation. Seulement

du personnel expérimenté devrait ouvrir ces chassis.

CAUTION/ATTENTION

Always ground yourself to remove any static charge

before touching the CPU card. Modern electronic devices

are very sensitive to static electric charges. As a safety

precaution, use a grounding wrist strap at all times. Place

all electronic components in a static-dissipative surface

or static-shielded bag when they are not in the chassis.

Toujours verifier votre mise à la terre afin d’éliminer toute

charge statique avant de toucher la carte CPU. Les

équipements électroniques moderns sont très sensibles

aux décharges d’électricité statique. Toujours utiliser un

bracelet de mise à la terre comme précaution. Placer

toutes les composantes électroniques sur une surface

conçue pour dissiper les charge, ou dans un sac anti-

statique lorsqu’elles ne sont pas dans le chassis.

- 7 -

CONTENTS

INTRODUCTION - 8 -

Features - 8 -

Package Contents - 9 -

Product Overview - 11 -

GETTING STARTED - 12 -

Turning On Your Device - 12 -

Connecting to Other Devices - 13 -

How to Enable Watchdog - 20 -

Turning Off Your Device - 22 -

INSTALLATION - 23 -

Wiring Requirements - 23 -

Mounting - 24 -

SPECIFICATIONS - 30 -

APPENDIX - 33 -

Appendix A: Cleaning the Monitor - 33 -

Appendix B: Winmate Software Development Kit - 34 -

- 8 -

INTRODUCTION

Congratulations on purchasing Winmate® 15” S-Series HMI.

Interactive and smart automation systems of intelligent buildings are

in a fast growing phase. Winmate® multi-touch S-Series HMI is

suitable for home automation and room management systems. Flat

surface is easy-to-clean and delivers aesthetically pleasing look for

any interior. The device provides real time update for booking status

and available schedule, or performs as a synchronous display in

meetings.

S-Series HMI runs on 1.83GHz Intel® Celeron® N2930 processor

and support Windows 10 IoT, Windows Embedded 8.1 Industry Pro,

Windows Embedded 8 Standard, and Windows Embedded Standard

7 – WS7P. The HMI features P-Cap touch-screen with 1024 x 768

pixel resolution. These models sealed with front IP 66 dust and water

proof, and full IP22.

The hardware installation becomes easier with PoE onboard which

combines data and power connections in a single cable. The

technology reduces the number of cables needed for the connection

of various devices. PoE infrastructure allows to centralized power

management, therefore it is a cost-effective solution for access

control, home and industrial automation.

Features

Winmate® 15” S-Series HMI features:

 15'' 1024 x 768 with Projected Capacitive Multi-Touch (P-CAP)

 Intel® Celeron® N2930 1.83GHz

 PoE standard IEEE 802.3at (25 W)

 Fanless cooling system and ultra-low power consumption

 Front IP65 water and dust proof

 Optional HF RFID Reader

 Optional RGBO LED Status Light Bar indicators on both sides

 0°C to +50°C

 Stylish design for room booking, access control and room

information applications

- 9 -

Package Contents

Carefully remove the box and unpack your device. Please check if all

the items listed below are inside your package. If any of these items

are missing or damaged contact us immediately.

Standard factory shipment list:

15” HMI Device

Quick Start Guide

(Hardcopy)

Driver CD & User

Manual

Varies by product

specifications

9152111I100T

IB32:

9171111I101Y

AC Adapter

(12V/ 50W)

Power Cord

Terminal Block 3

922D050W12VA

Varies by country

94J602G030K0

- 10 -

Package may include optional accessories based on your order:

VESA Desk Stand

LA-100

VESA Wall Mount

Bracket

LA-106

Front Side

Wall Mount Kit

PCFW-V2

9B0000000128

9B0000000412

99K000A00006.

- 11 -

Product Overview

Unit: mm

№

Description

№

Description

①

RJ-45 (LAN)

⑥

Digital I/O (Optional)

②

USB 3.0 x 1 , USB 2.0 x 1

⑦

HF RFID Reader

(Optional)

③

RS232/422/485

⑧

LED Status Light Bar

(Optional)

④

12V DC Terminal Block

⑨

1 Watt Speaker x 2

⑤

RJ-45 (LAN/ PoE)

- 12 -

GETTING STARTED

Turning On Your Device

Follow the following steps to turn on your device:

1. Connect HMI device to a thermal block (3-pin).

2. Connect the other side of the thermal block to the AC adapter.

3. Connect the AC adapter to the power cord.

4. Plug in the power cord to a working AC wall outlet. The device

will boot automatically.

CAUTION

Use only the AC adapter included in your package.

Using other AC adapters may damage the device.

ALTERNATING CURRENT

This product must be grounded. Use only a grounded

AC outlet. Install the additional PE ground wire if the

local installation regulations require it.

- 13 -

Connecting to Other Devices

This section explains how to connect external interfaces to the HMI

device.

Power Connector

DC power source input is a 3 pin terminal block connector.

Serial Port Connector

Use COM1 serial port connector to connect your HMI to external

devices such as mouse, modem or printer. You can configure serial

port setting via jumpers located on the motherboard. You need to

open the housing in order to access the jumpers.

CAUTION/ ATTENTION

It is recommended to use factory jumper settings.

Opening the housing when it is sealed may damage the

device and its parts.

Refer to User Manual for instructions on how to configure serial port

setting.

Voltage

Minimum Voltage 11.4V

Maximum Voltage 12.6V

Maximum Current 4.2A

Pin №

RS-232

(Default)

RS-422

RS-485

1

DCD

TxD-

D-

2

RXD

TxD+

D+

3

TXD

RxD+

NC

4

DTR

RxD-

NC

5

GND

6

DSR

NC

7

RTS

NC

8

CTS

NC

9

RI

NC

- 14 -

RJ45 Connector

The 15” S-Series HMI has two RJ45 connectors that support

10/100/1000 Mbps Ethernet interface for connecting to the internet.

Notice that only one RJ45 connector supports PoE function.

IMPORTANT:

Power Device (PD): follows IEEE 802.3at (25 Watt)

USB 2.0 and USB 3.0 Connector

Use USB 2.0 and USB 3.0 connector to connect your HMI device to

other USB 2.0/ USB 3.0 compatible devices.

USB2.0 and USB 3.0

Pin №

Signal Name

Pin №

Signal

Name

1

TX1+

2

TX1-

3

TX2+

4

TX2-

5

TX3+

6

TX3-

7

TX4+

8

TX4-

Pin №

Signal Name

Pin №

Signal Name

1

+5V

2

USB_D-

3

USB_D+

4

GND

5

STDA_SSRX-

6

STDA_SSRX+

7

GND_DRAIN

8

STDA_SSTX-

9

STDA_SSTX+

10

+5V

11

USB_D-

12

USB_D+

13

GND

- 15 -

Digital I/O Connector

Notice that Digital I/O is an optional connector and may not be

present in your model.

Pin №

Signal Name

Pin №

Signal Name

1

GND

2

DI0

3

DI1

4

DI2

5

DI3

6

DO0

7

DO1

8

DO2

9

DO3

10

VCC

- 16 -

Using HF RFID Reader

Notice that HF RFID Reader is an optional feature for 10.1” S-Series

HMI and may not be present in your device.

HF RFID is commonly used for ticketing, payment, and data transfer

applications.

The RFID Reader is located on the bottom right front side of the HMI

device.

The COM Port setting in RFID Reader is “COM 14”

1. Double-click the RFID icon on the Windows desktop.

2. Reader menu appears on the screen as shown below.

Note:

The picture below of Reader Demo Version 1.4 is for

illustration purposes only. Your Reader version may differ

from the picture below.

- 17 -

Reader Demo Version 1.04

Reading Mode

Select the default RFID Reader COM14or press Search on the upper

left corner of the screen. The system will automatically find RFID

COM port, show the Version.

Item №

Key button

Function

1

E1- Version

Displays the current version of RFID

Reader system

2

E2- Reset

Reset all settings

- 18 -

UID0 Menu

The system will read the data once the card will be near. You can

select different reader modes. Each mode is described below.

Item №

Key button

Function

3

A0- Continuous

Read (default)

The RFID Reader will perform a

series of multiple scanning

operations

4

A1- Once Read

The RFID Reader will perform a

single scanning operation during the

card is near

5

A9- Type Read

The RFID Reader will perform a

scanning operation of IC type tag

To scan the card, bring it close to the right bottom front side of

device with RFID icon.

Item №

Data 32

Function

6

XXXXABCDEF

Display the information written in the

card

- 19 -

Writing Mode

Refer to the RFID Porting Guide SDK to configure Write Mode

parameters.

- 20 -

How to Enable Watchdog

To enable Watchdog, you need to download Winmate Watchdog

utility. Find more information on Watchdog in “Watchdog Guide” that

you can download from Winmate Download Center or File Share.

Refer to the User Manual for more details.

To enable watchdog in Watchdog AP follow the instructions below:

1. On the right bottom side of the desktop screen, click triangle

button to show hidden icons.

2. Click icon to open Watchdog utility.

3. In Watchdog utility window set countdown time and periodically

feed time, or disable watchdog.

La page charge ...

Winmate 7'' S-Series Guide de démarrage rapide

Ce manuel convient également à

Winmate 7'' S-Series Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents