Simplicity 020248-0 Manuel utilisateur

Marque: Simplicity

Modèle: 020248-0

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

PRESSURE WASHER

3.75 HORSEPOWER

2,000 PSI

2.0 GPM

PRESSURE WASHER

CUSTOMER HELPLINE

1-800-222-3136

Model No. 580.676640

HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)

Part No. 196284GS Draft 0 (02/21/2005)

Sears Canada, Inc.

Visit our Craftsman website: www.sears.ca

Owner’s Manual

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Français

ATTENTION

Avant d’utiliser ce produit, veuillez lire

le manuel et suivre toutes les directives

relatives à la sécurité et à l’utilisation.

CAUTION

Before using this product, read this

manual and follow all Safety Rules and

Operating Instructions.

Read this manual carefully and become

familiar with your pressure washer. Know its

applications, its limitations, and any hazards

involved.

The safety alert symbol ( ) is used with a signal

word (DANGER, CAUTION, WARNING), a pictorial

and/or a safety message to alert you to hazards.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury. WARNING indicates a

hazard which, if not avoided, could result in death or

serious injury. CAUTION indicates a hazard which, if

not avoided, might result in minor or moderate injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in equipment

damage. Follow safety messages to avoid or reduce

the risk of injury or death.

Hazard Symbols and Meanings

TABLE OF CONTENTS

WARRANTY

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN PRESSURE WASHER

For one year from the date of purchase, when this CRAFTSMAN® Pressure Washer is maintained and operated

according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and

workmanship.

If this pressure washer is used for commercial purposes, this warranty applies for only 90 days from the date of

purchase.

If this pressure washer is used for rental purposes, this warranty applies for only 30 days after date of purchase.

This warranty does not cover:

• Expendable items such as spark plugs and air filters, which become worn during normal use.

• Repairs necessary because of operator abuse or negligence, including damage resulting from no water being

supplied to pump or failure to maintain the equipment according to the instructions contained in the owner's

manual.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE PRESSURE WASHER TO THE NEAREST

SEARS SERVICE CENTER OR DEALER IN CANADA.

This warranty gives you specific legal rights and you may also have other rights, which vary from province to

province.

Sears Canada, Inc.

SAFETY RULES

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

FEATURES & CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . 5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

HOW TO ORDER PARTS. . . . . . . . . . . . . . . . . . . . . . . . . 21

REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . 22-27

EMISSION CONTROL WARRANTY . . . . . . . . . . . . . . 28-29

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-52

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate pressure washer inside any building or

enclosure.

• Use a respirator or mask whenever there is a chance

that vapors may be inhaled.

• Read all instructions packed with mask so you are certain

mask will provide necessary protection against inhaling

harmful vapors.

Running engine gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause

nausea, fainting or death.

Some chemicals or detergents may be

harmful if inhaled or ingested, causing

severe nausea, fainting or poisoning.

WARNING

• Keep spray nozzle between 8 to 24 inches away from

cleaning surface.

• Operate this unit on a stable surface.

• Cleaning area should have adequate slopes and

drainage to reduce possibility of falls due to slippery

surfaces.

• Be extremely careful if you must use pressure washer

from a ladder, scaffolding or any other relatively unstable

location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

Use of pressure washer can create puddles

and slippery surfaces.

High pressure spray could cause you to fall

if you are too close to the cleaning surface.

WARNING

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap and air cleaner are

in place.

• DO NOT crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which causes

fuel to spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• NEVER aim spray gun at people, animals or plants.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any

kind. Replace o-ring or seal.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• Squeeze trigger on spray gun to relieve trapped

pressure, every time you stop engine. Engage trigger

lock on spray gun.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury

and possible amputation.

Spray gun retains high pressure when

pressure washer is shut down, which can

cause injury.

WARNING

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze

trigger on spray gun.

Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster

than you can let go.

Broken bones, fractures, bruises or sprains

could result.

WARNING

• If you have questions about intended use, ask dealer or

contact Sears.

• NEVER operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by–pass any safety device on this machine.

• Before starting pressure washer in cold weather, check

all parts of the equipment to be sure ice has not formed

there.

• NEVER move machine by pulling on high pressure hose.

Use handle provided on unit.

• Check fuel system for leaks or signs of deterioration,

such as chafed or spongy hose, loose or missing

clamps, or damaged tank or cap. Correct all defects

before operating pressure washer.

• This equipment is designed to be used with Sears

authorized parts ONLY. If equipment is used with parts

that DO NOT comply with minimum specifications, user

assumes all risks and liabilities.

Improper treatment of pressure washer can

damage it and shorten its life.

CAUTION

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running.

• NEVER use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories

are correctly attached.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

• DO NOT point spray gun at glass when in jet spray mode.

• NEVER aim spray gun at plants.

High pressure spray may damage fragile items

including glass.

CAUTION

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

Excessively high or low operating speeds increase

risk of injury and damage to pressure washer.

CAUTION

• DO NOT wear loose clothing, jewelry or anything that

may be caught in starter or other rotating parts.

• Tie up long hair and remove jewelry.

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

WARNING

• Always wear eye protection when using equipment or when

in vicinity of equipment in use.

High pressure spray can cause paint chips

or other particles to become airborne.

WARNING

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials.

• Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

Running engines produce heat.

Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, etc. can catch fire.

WARNING

• Keep water spray away from electric wiring or fatal

electric shock may result.

Spray contact with electrical wiring can

result in electrocution.

WARNING

KNOW YOUR PRESSURE WASHER

Read the owner’s manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

FEATURES AND CONTROLS

Detergent Pick–Up

Tube and Filter

Recoil Starter

Oil Fill Cap and Dipstick

Air Filter

Fuel Cap

High Pressure Outlet

Water Inlet

Pump equipped with

Automatic Cool Down System

Throttle Control

Lever

Adjustable Nozzle (not shown) – Adjust for high or

low pressure; narrow or fan spray.

Air Filter — Protects engine by filtering dust and

debris out of intake air.

Automatic Cool Down System — Cycles water

through pump when water reaches 125°-155°F. Warm

water will discharge from pump onto ground. This

system prevents internal pump damage.

Detergent Pick–Up Tube and Filter – Used to siphon

detergent from chemical bottle to the low pressure

water stream.

Fuel Cap – Fill fuel tank with regular unleaded fuel

here.

High Pressure Hose (not shown) – Connect one end

to the spray gun and other end to the high pressure

outlet.

High Pressure Outlet — Connection for high

pressure hose.

Nozzle Extension (not shown) — Attach to spray

gun to use adjustable nozzle.

Oil Fill Cap and Dipstick – Check and fill engine with

oil here. See page 7 for oil recommendations and

filling instructions.

Primer Bulb — Prepares a cold engine for starting.

Pump — Develops high water pressure.

Recoil Starter — Used for starting the engine

manually.

Spray Gun (not shown) – Controls the application of

water onto cleaning surface with trigger device.

Includes trigger lock.

Throttle Control Lever – Sets engine in starting

mode for recoil starter and stops running engine.

Water Inlet — Connection for garden hose.

Primer Bulb

Your pressure washer requires some assembly and is

ready for use only after it has been properly serviced

with the recommended oil and fuel.

If you have any problems with the assembly of

your pressure washer, please call the pressure

washer helpline at 1-800-222-3136.

IMPORTANT: Any attempt to run the engine before it

has been serviced with the recommended oil will result

in an engine failure.

REMOVE PRESSURE WASHER

FROM CARTON

• Open carton and slice two corners from top to

bottom so the panel can be folded down flat.

• Remove fillers, accessories and parts bag shipped

with your pressure washer.

• Remove the pressure washer out the open end of

the carton.

• Check carton for additional loose parts.

CARTON CONTENTS

Check all contents. If any parts are missing or damaged,

call the pressure washer helpline at 1-800-222-3136.

• The main unit

• Handle

• High pressure hose

• Spray gun

• Nozzle extension with adjustable nozzle

• Turbo nozzle

• Wheel kit

• Safety goggles

• Engine oil

• Parts bag (which includes items listed below)

Owner’s manual

Become familiar with each piece before assembling

the pressure washer. Compare contents against the

view on page 5. If any parts are missing or damaged,

call the pressure washer helpline at 1-800-222-3136.

ASSEMBLING YOUR PRESSURE

WASHER

Your Craftsman pressure washer was mostly

assembled at the factory. However, you will need to

perform these tasks before you can operate your

pressure washer:

1. Attach handle to main unit.

2. Install wheel kit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

Attach Handle

1. Place plastic adapters in hinges on handle

extension as shown.

NOTE: Make sure lip on plastic adapters is facing up

in hinges.

2. Clamp handle extension onto pressure washer

handle and insert T-bolts into holes of clamp.

Tighten by hand.

Install Wheel Kit

The wheel kit is designed to greatly improve the

portability of your pressure washer.

NOTE: Wheel kit is not intended for over-the-road use.

Install the wheel kit as follows:

1. Place the bottom of the pressure washer frame on a

flat, even surface, such as blocks to ease assembly.

2. Spread axle brackets apart and place over front

vibration mounts on the pressure washer frame as

shown.

3. Squeeze axle brackets back to original shape.

ASSEMBLY

4. Slide axle through holes in both axle brackets, as

shown.

5. With raised hub inward, slide wheels over axle on

each side of pressure washer frame.

6. Install retaining clips into grooves on axle to retain

wheels.

7. Remove the temporary blocks.

Add Engine Oil

IMPORTANT: Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine failure.

NOTE: When adding oil to the engine crankcase, use

only high quality detergent oil rated with API service

classification SF, SG, SH, SJ or higher. DO NOT use

special additives.

1. Choose a viscosity according to the following table.

* The use of multi-viscosity oils (5W-30, 10W-30, etc.)

in temperatures above 40°F (4°C) will result in higher

than normal oil consumption. When using a multi-

viscosity oil, check oil more frequently.

** If using SAE 30 oil in temperatures below 40°F

(4°C), it will result in hard starting and possible

engine bore damage due to inadequate lubrication.

2. Place pressure washer on a level surface and

clean area around oil fill.

3. Remove dipstick and wipe clean with cloth.

4. Replace and tighten dipstick.Remove and check

oil level.

5. Slowly pour oil into oil fill opening. Pause to permit

oil to settle. Fill to “Full” mark on dipstick. DO NOT

OVERFILL. Remove dipstick and check oil level.

NOTE: You may not need to use all the supplied oil.

6. Replace dipstick and tighten securely.

NOTE: Check oil often during engine break–in.

Add Fuel

NOTE: This engine is certified to operate on gasoline.

Exhaust Emission Control System: EM (Engine

Modifications).

1. Use clean, fresh, regular UNLEADED fuel with a

minimum of 77 octane with equipment. DO NOT

use fuel which contains Methanol. DO NOT mix oil

with fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be

careful not to overfill. Allow about 1.5" of tank

space for fuel expansion, as shown here.

4. Install fuel cap and wipe up any spilled fuel.

CAUTION! Alcohol-blended fuels (called gasohol,

ethanol or methanol) can attract moisture, which leads

to separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine

while in storage.

To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer. Drain the

fuel tank, start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next season.

See “Storage” on pages 18-19 for additional information.

NEVER use engine or carburetor cleaner products in

the fuel tank as permanent damage may occur.

Synthetic 5W-30, 10W-30

5W-30, 10W-30

°F -20 0 20 32 40 60 80 100

°C -30 -20 -10 0 10 20 30 40

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

Fuel

Tank

1.5” Air Space

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must

assemble the nozzle extension to the spray gun and

attach all hoses before you start the engine.

1. Uncoil high pressure hose and attach one end of

hose to base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high

pressure outlet on pump. Tighten by hand.

3. Before connecting garden hose to water inlet,

inspect inlet screen. Clean screen if it contains

debris or have it replaced if damaged. Refer to

section “O-Ring Maintenance” if inlet screen is

damaged. DO NOT run pressure washer if inlet

screen is damaged.

4. Run water through garden hose for 30 seconds to

flush it of debris. Turn off water.

IMPORTANT: DO NOT siphon standing water for the

water supply. Use ONLY cold water (less than 100°F).

5. Connect garden hose (not to exceed 50 feet in

length) to water inlet. Tighten by hand.

6. Turn ON water and squeeze trigger on gun to

purge pump system of air and impurities.

CHECKLIST BEFORE STARTING

ENGINE

Review the unit to ensure you have performed all of

the following:

1. Check that oil has been added to proper level in

engine crankcase.

2. Add proper fuel to fuel tank.

3. Check for properly tightened hose connections

(high pressure and water supply) and there are no

kinks, cuts, or damage to high pressure hose.

4. Provide proper water supply (not to exceed 100°F).

5. Be sure to read “Safety Rules” and “Operation”

sections before using pressure washer.

6. If starting unit after storage, see “Storage” section

on pages 18-19.

Inspect inlet

screen. DO

NOT use if

damaged;

clean if dirty.

CAUTION

• Damage to equipment resulting from failure to follow

this instruction will void warranty.

There MUST be at least ten feet of unrestricted garden

hose between the pressure washer inlet and any flow

shut off device, such as a ‘Y’ shut-off connector or

other convenience-type water shut-off valve.

• Always wear eye protection when using this equipment

or in vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are

wearing adequate eye protection.

High pressure spray can cause paint chips

or other particles to become airborne.

WARNING

HOW TO USE YOUR PRESSURE

WASHER

If you have any problems operating your pressure

washer, please call the pressure washer helpline at

1-800-222-3136.

Pressure Washer Location

Pressure Washer Clearance

The pressure washer must be at least 5 ft. (152 cm)

from structures having combustible walls and/or other

combustible materials. Leave at least 3 ft. (92 cm) all

around pressure washer including overhead, for

adequate cooling, maintenance and servicing.

Place pressure washer in a well ventilated area, which

will allow for removal of deadly exhaust gas. DO NOT

place pressure washer where exhaust gas could

accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is

kept away from any windows, doors, ventilation

intakes or other openings that can allow exhaust gas

to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when

positioning pressure washer.

To Start Your Pressure Washer

To start your engine-powered pressure washer for the

first time, follow these instructions step-by-step. This

starting information also applies whenever you start

the engine after you have let the pressure washer sit

idle for at least a day.

1. Place pressure washer near an outside water

source capable of supplying water at a flow rate

greater than 3.0 gallons per minute and no less than

20 PSI at pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected

to spray gun and pump. See “Assembling Your

Pressure Washer” for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump. Turn ON water.

5. Squeeze trigger on gun to purge pump system of

air and impurities.

6. Attach nozzle extension to spray gun. Tighten by

hand.

7. Position nozzle in low pressure mode (slide nozzle

forward) and squeeze trigger on spray gun to

relieve pressure caused by turning ON water.

Water will flow out of gun in a thin stream.

Continue to hold trigger until there is a steady

stream of water and no air remains in system.

Release trigger.

8. Engage safety latch to spray gun trigger.

Safety Latch

OPERATION

CAUTION

• Damage to equipment will result from failure to follow

this instruction.

DO NOT run the pump without the water supply

connected and turned on.

Exhaust Port

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate pressure washer inside any building or

enclosure.

Running engine gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause

nausea, fainting or death.

WARNING

Typical Pressure

Washer Shown

9. Move throttle lever to “Fast” position, shown here

as a rabbit.

NOTE: For a warm engine, be sure the throttle lever is

in the “Fast” position.

To start the engine for the very first time:

10. Make sure throttle lever is in “Fast” position

(indicated on the engine as a rabbit).

11. Push primer bulb firmly 5 times, waiting 2 seconds

between each push.

To start engine thereafter:

10. Make sure throttle lever is in “Fast” position

(indicated on the engine as a rabbit).

11. Press primer bulb firmly 3 times, waiting

2 seconds between each push. For a warm

engine, DO NOT press primer bulb.

12. Grasp starter grip handle and pull slowly until you

feel some resistance. Then pull rapidly to start

engine.

13. Return starter grip handle slowly. DO NOT let rope

“snap back” against starter.

NOTE: Always keep the throttle lever in the “Fast”

position when operating the pressure washer.

How to Stop Your Pressure Washer

1. Let engine idle for two minutes.

2. Move throttle lever on engine to “Stop” position.

3. Squeeze trigger on spray gun to relieve

trapped pressure in hose to avoid injury.

NOTE: A small amount of water will squirt out when

pressure is released.

4. Engage trigger lock on spray gun when not in use.

How To Use the Adjustable Nozzle

You now should know how to START your pressure

washer and how to STOP it. The information in this

section will tell you how to adjust the spray pattern

and apply detergent or other cleaning chemicals.

On the end of your spray gun is a nozzle handle that

can adjust the spray pressure and the spray pattern.

• NEVER adjust spray pattern when spraying.

• NEVER put hands in front of nozzle to adjust spray pattern.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

Throttle

Lever in

STOP

position

Stop

Fast

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze

trigger on spray gun.

Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster

than you can let go.

Broken bones, fractures, bruises or sprains

could result.

WARNING

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials.

• Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

Running engines produce heat.

Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, etc. can catch fire.

WARNING

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• Squeeze trigger on spray gun to relieve trapped

pressure, every time you stop engine. Engage trigger

lock on spray gun.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury

and possible amputation.

Spray gun retains high pressure when

pressure washer is shut down, which can

cause injury.

WARNING

1. Sliding nozzle forward and back adjusts spray

pressure.

2. Point nozzle toward ground, disengage safety

latch, and press trigger to test pattern.

3. Rotating nozzle adjusts spray pattern from a

narrow pattern to a fan pattern.

4. For most effective cleaning, keep spray nozzle

between 8 to 24 inches away from cleaning

surface.

5. If you get spray nozzle too close, especially using

high pressure mode, you may damage the surface

being cleaned.

6. DO NOT get closer than 6 inches when cleaning

tires.

Using the Turbo Nozzle

The turbo nozzle rotates the high pressure stream in a

rapid circular pattern. The high pressure spray is most

effective when the tip of the nozzle extension is held

between 8 to 24 inches from the surface being cleaned.

To attach the turbo nozzle to the spray gun:

1. Engage safety latch to spray gun trigger.

2. Remove the nozzle extension from the spray gun,

if attached.

3. Attach the turbo nozzle extension to spray gun.

Tighten by hand.

4. Disengage safety latch to spray gun trigger.

5. Always start the turbo nozzle at a distance,

gradually getting closer to the surface until you get

the cleaning force you want.

NOTE: Detergent cannot be applied with turbo nozzle.

Applying Detergent with Adjustable Nozzle

IMPORTANT: Use chemicals designed specifically for

pressure washers. Household detergents could

damage the pump.

Twist nozzle counter-

clockwise for fan pattern.

Twist nozzle clockwise for

narrow spray pattern.

Slide nozzle backward for

high pressure mode.

Slide nozzle forward for low

pressure mode and

detergent application.

CAUTION

• Starting the engine without all the hoses connected and

without the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

You must attach all hoses before you start the engine.

CAUTION

• Always make sure the surface you will clean will not be

damaged by the high pressure spray by testing in a

hidden area.

The turbo nozzle produces an extremely high

pressure spray which is capable of removing paint

and cutting holes through surfaces if held too close.

To apply detergent, follow these steps:

1. Review use of adjustable nozzle.

2. Prepare detergent solution as required by job.

3. Place filter end of detergent siphoning tube into

detergent container.

4. Slide adjustable nozzle forward to low pressure

mode. Detergent cannot be applied with nozzle in

high pressure position.

5. Make sure garden hose is connected to water

inlet. Check that high pressure hose is connected

to spray gun and pump. Start engine.

6. Apply detergent to a dry surface, starting from

bottom and working up.

7. Allow detergent to “soak in” for 3-5 minutes before

rinsing. Reapply as needed to prevent surface

from drying.

8. For washing, start at lower portion of area to be

washed and work upward, using long, even,

overlapping strokes.

IMPORTANT: You must flush the chemical injection

system after each use by placing the filter into a clean

bucket of water and running the pressure washer in

low pressure for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1. Slide nozzle backward to high pressure, press

trigger and wait for detergent to clear.

NOTE: You can also stop detergent flow by removing

detergent siphoning tube from container.

2. Keep spray gun a safe distance from area you

plan to spray.

3. Apply a high pressure spray to a small area, then

check surface for damage. If no damage is found,

it is okay to continue cleaning.

4. Start at top of area to be rinsed, working down

with same overlapping strokes as you used for

washing and applying detergent.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must

flush it with clean water before stopping the engine.

1. Place chemical injection siphon/filter in a bucket

full of clean water.

2. Slide adjustable nozzle forward to low pressure

position.

3. Flush for 1-2 minutes.

4. Shut off engine.

IMPORTANT: Simply shutting OFF engine will not

release pressure in the system. When the engine has

shut down, squeeze the trigger on the spray gun

to relieve the pressure in the hose.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray

gun, circulating water in the pump can reach

temperatures above 125°F (51°C). The system

engages to cool the pump by discharging the warm

water onto the ground.

• Keep spray nozzle between 8 to 24 inches away from

cleaning surface.

• Operate this unit on a stable surface.

• Be extremely careful if you must use the pressure

washer from a ladder, scaffolding or any other relatively

unstable location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

High pressure spray could cause you to fall

if you are too close to the cleaning surface.

WARNING

CAUTION

• When inserting the filter into a detergent solution bottle,

route the tube so as to keep it from inadvertently

contacting the hot muffler.

Keep the chemical injection tube from coming in

contact with the hot muffler.

ENGINE TECHNICAL INFORMATION

This is a single cylinder, L-head, air cooled engine. It

is a low emissions engine.

In the State of California, Model Series

100000 engines are certified by the California Air

Resources Board to meet emissions standards for

125 hours. Such certification does not grant the

purchaser, owner or operator of this engine any

additional warranties with respect to the performance

or operational life of this engine. The engine is

warranted solely according to the product and

emissions warranties stated elsewhere in this manual.

Power Ratings

The power ratings for an individual engine model are

initially developed by starting with SAE (Society of

Automotive Engineers) code J1940 (Small Engine

Power & Torque Rating Procedure) (Revision 2002-

05). Given both the wide array of products on which

our engines are placed, and the variety of

environmental issues applicable to operating the

equipment, it may be that the engine you have

purchased will not develop the rated horsepower when

used in a piece of power equipment (actual “on-site”

power). This difference is due to a variety of factors

including, but not limited to, the following: differences

in altitude, temperature, barometric pressure, humidity,

fuel, engine lubrication, maximum governed engine

speed, individual engine to engine variability, design of

the particular piece of power equipment, the manner in

which the engine is operated, engine run-in to reduce

friction and clean out of combustion chambers,

adjustments to the valves and carburetor, and other

factors. The power ratings may also be adjusted

based on comparisons to other similar engines utilized

in similar applications, and will therefore not

necessarily match the values derived using the

foregoing codes.

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

Pressure . . . . . . . . . . . . . . . . . . 2,000 PSI

Flow Rate . . . . . . . . . . . . . . . . . 2.0 GPM

Chemical Mix. . . . . . . . . . . . . . . Use as directed

Water Supply Temperature. . . . Not to exceed 100°F

Shipping Weight . . . . . . . . . . . . 48 lbs.

Engine Specifications

Rated Horsepower . . . . . . . . . . . . 3.75 at 3600 rpm

Bore . . . . . . . . . . . . . . . . . . . . . . . 2.562 in. (65.09 mm)

Stroke . . . . . . . . . . . . . . . . . . . . . . 1.875 in. (47.63 mm)

Displacement . . . . . . . . . . . . . . . . 9.67 in. (158.6 cc)

Spark Plug

Type: . . . . . . . . . . . . . . . . . . . . . Champion RJ-19LM or

Equivalent

Set Gap To: . . . . . . . . . . . . . . . 0.030inch (0.76mm)

Armature Air Gap: . . . . . . . . . . . . 0.006-0.010 in.

(0.15-0.25mm)

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

Intake . . . . . . . . . . . . . . . . . . . . . . 0.005-0.007 in.

(0.13-0.18 mm)

Exhaust . . . . . . . . . . . . . . . . . . . . 0.007-0.009 in.

(0.18-0.23 mm)

Fuel Capacity . . . . . . . . . . . . . . . . 1.0 Quarts

Oil Type:

Above 40° F . . . . . . . . . . . . . . . SAE 30

Below 40° F . . . . . . . . . . . . . . . SAE 5W-30 or 10W-30

NOTE: For practical operation, the horsepower

loading should not exceed 85% of rated horsepower.

Engine power will decrease 3-1/2% for each

1,000 feet (300 meters) above sea level and 1% for

each 10° F (5.6° C) above 77° F (25° C). It will

operate satisfactorily at an angle up to 15°.

SPECIFICATIONS

GENERAL RECOMMENDATIONS

Regular maintenance will improve the performance

and extend the life of the pressure washer. See any

authorized Sears dealer for service.

The pressure washer warranty does not cover items

that have been subjected to operator abuse or

negligence. To receive full value from the warranty,

the operator must maintain pressure washer as

instructed in this manual including proper storage as

detailed in “Storage” on pages 18-19.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least

once each season. Follow the requirements in the

“Maintenance Schedule” chart above.

NOTE: Once a year you should clean or replace the

spark plug and replace the air filter. A new spark plug

and clean air filter assure proper fuel-air mixture and

help your engine run better and last longer.

EMISSION CONTROL

Maintenance, replacement or repair of the emission

control devices and systems may be performed by any

non-road engine repair establishment or individual.

BEFORE EACH USE

1. Check engine oil level.

2. Check water inlet screen for damage.

3. Check in-line filter for debris.

4. Check high pressure hose for leaks.

5. Check chemical filters for damage.

6. Check gun and nozzle extension assembly for

leaks.

7. Purge pump of air and contaminants.

PRESSURE WASHER

MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from

pressure washer. Keep linkage, spring and controls

clean. Keep area around and behind muffler free from

any combustible debris.

MAINTENANCE

OWNER’S RESPONSIBILITIES

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse conditions noted below.

¹ Clean if clogged. Replace if perforated or torn.

² Change oil after the first (5) operating hours and every 50 hours or yearly thereafter.

Change sooner when operating under dirty or dusty conditions.

³ Replace more often under dirty or dusty conditions.

MAINTENANCE SCHEDULE

FILL IN DATES AS YOU

COMPLETE REGULAR SERVICE

OPERATING INTERVALS

SERVICE DATES

MAINTENANCE TASK

Before

Each Use

Every 25

Hours or

Yearly

Every 50

Hours or

Yearly

Every 100

Hours or

Yearly

100-300

Hours

PRESSURE WASHER

Check/clean water inlet screen

X¹

Check high pressure hose X

Check detergent hose X

Check spray gun and assembly for leaks X

Purge pump of air and contaminants X

Change pump oil X

Prepare pump for storage below 32°F See Storage on pages 18-19.

ENGINE

Check oil level

Clean debris X

Change engine oil X²

Service air cleaner X³

Service spark plug X

Service spark arrester X

Clean cooling system X²

Clean combustion chamber X

Prepare for storage If unit is to remain idle for longer than 30 days.

Pressure washer parts should be kept clean to reduce the

risk of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt, oil,

etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Use low pressure air (not to exceed 25 psi) to blow

away dirt. Inspect cooling air slots and openings on

the pressure washer. These openings must be kept

clean and unobstructed.

Check and Clean Inlet Screen

Examine garden hose inlet screen. Clean if it is

clogged or replace if it is torn.

Check High Pressure Hose

High pressure hoses can develop leaks from wear,

kinking, or abuse. Inspect hose before each use.

Check for cuts, leaks, abrasions, bulging of cover, or

damage or movement of couplings. If any of these

conditions exist, replace hose immediately.

Check Gun and Nozzle Extension

Examine hose connection to gun and make sure it is

secure. Test trigger by pressing it and making sure it

springs back into place when you release it. Engage

safety latch and test trigger. You should not be able to

press trigger. Replace gun immediately if it fails any of

these tests.

Check In-Line Filter

Refer to the illustration and service the in-line filter if it

becomes clogged, as follows:

1. Detach nozzle extension from gun and remove

o-ring and screen from nozzle extension. Flush

screen, gun, and nozzle extension with clean water

to clear debris.

2. Place in-line filter screen into threaded end of

nozzle extension. Direction does not matter. Push

screen in with eraser end of pencil until it rests flat

at bottom of opening. Take care not to bend

screen.

3. Place o-ring into recess. Push o-ring snugly against

in-line filter screen.

4. Assemble nozzle extension to spray gun, as

described earlier in manual.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure.

The principal cause of excessive pump pressure is a

nozzle clogged or restricted with foreign materials,

such as dirt, etc. To correct the problem, immediately

clean the nozzle following these instructions:

1. Shut off engine and turn off water supply.

2. Remove nozzle from end of nozzle extension.

Separate nozzle extension from spray gun. Twist

nozzle clockwise to stream position. Using a 2mm

(5/64) allen wrench, remove orifice from end of

nozzle extension.

3. Remove in-line filter from other end of nozzle

extension.

4. Use a small paper clip to free any foreign material

clogging or restricting orifice.

5. Using a garden hose, remove additional debris by

back flushing water through nozzle extension. Back

flush between 30 to 60 seconds. Turn adjustable

nozzle extension to stream spray and move nozzle

from low to high while flushing.

6. Reinstall orifice and in-line filter into nozzle

extension. DO NOT overtighten orifice with allen

wrench.

7. Reconnect nozzle extension to spray gun.

8. Reconnect water supply, turn on water, and start

engine.

9. Test pressure washer by operating nozzle in high

and low positions.

Nozzle extension

In-line Filter

O-ring

Insert wire into orifice and turn back

and forth to clear obstruction.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum

pressure rating of unit.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury

and possible amputation.

WARNING

• DO NOT insert any objects through cooling slots.

Improper treatment of pressure washer can

damage it and shorten its life.

CAUTION

O–Ring Maintenance

Purchase an O–Ring Repair Kit, item number

191922GS, at your local Sears sevice center. It is not

included with the pressure washer. This kit includes

replacement o-rings, rubber washer and water inlet filter.

Refer to the instruction sheet provided in the kit to

service your unit’s o-rings.

Pump Maintenance

Changing Pump Oil

Change oil every 50 hours or once yearly, whichever

occurs first.

NOTE: You must purchase a premeasured bottle of

pump oil, item number 190586GS at your local Sears

sevice center.

Change pump oil as follows:

1. Drain engine oil and fuel from pressure washer.

2. Use a 8mm allen wrench to remove black pump

oil cap between high pressure outlet and garden

hose inlet.

3. Tilt pressure washer to drain oil into an approved

container until it drips slowly from pump.

4. Tilt pressure washer in opposite direction and

empty premeasured pump oil bottle into same

opening (a small funnel may be helpful).

5. Install black pump oil cap and tighten firmly.

6. Set pressure washer in upright position. Add fuel

and engine oil.

ENGINE MAINTENANCE

Checking Oil Level

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

Changing Oil

Change engine oil after the first 5 hours and every

50 hours thereafter. If you are using your pressure

washer under extremely dirty or dusty conditions, or in

extremely hot weather, change oil more often.

KEEP OUT OF REACH OF CHILDREN.

DON'T POLLUTE. CONSERVE

RESOURCES. RETURN USED OIL TO

COLLECTION CENTERS.

Change oil while engine is still warm from running,

as follows:

1. Drain fuel tank by running pressure washer until

fuel tank is empty.

2. Disconnect spark plug wire and keep it away from

spark plug.

3. Clean area around oil fill, remove oil fill

cap/dipstick. Wipe dipstick clean.

4. Tip your pressure washer to drain oil from oil fill

into a suitable container making sure you tip your

unit away from spark plug and air cleaner. When

crankcase is empty, return pressure washer to

upright position.

5. Wipe dipstick clean, insert it into oil fill hole and

tighten securely, remove dipstick. Add

recommended oil up to “Full” mark on dipstick.

Pour slowly. Wipe dipstick clean each time oil

level is checked. DO NOT overfill.

6. Install oil fill plug and dipstick, tighten securely.

7. Wipe up any remaining oil.

8. Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be

damaged if you run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of

operation or once each year, whichever comes first.

Service more often if operating under dirty or dusty

conditions. Replacements are available at your local

Sears service center.

To service the air cleaner, follow these steps:

1. Remove screw.

Oil Cap

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

• NEVER repair leaking connections with sealant of any

kind. Replace o-ring or seal.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury

and possible amputation.

WARNING

2. Carefully remove air cleaner assembly to prevent

debris from falling into carburetor.

3. Take air cleaner assembly apart and clean all

parts. Wash foam air cleaner in liquid detergent

and water. Squeeze dry in a clean cloth.

4. SATURATE foam air cleaner in engine oil and

squeeze in a clean cloth to remove excess oil.

5. Reinstall clean or new foam air cleaner in body.

6. Install air cleaner securely on carburetor with

screw.

Service Spark Plug

Service the spark plug every 100 hours of operation or

yearly, whichever occurs first.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug with recommended plug if

electrodes are worn or if insulator is cracked or

chipped.

4. Check electrode gap with wire feeler gauge and

set gap at 0.030 inches (0.76mm), if necessary.

5. Install spark plug, tighten securely.

Spark Arrester Service

Your engine is not factory-equipped with a spark

arrester. In some areas, it is illegal to operate an

engine without a spark arrester. Check local laws and

regulations. A spark arrester is available from your

nearest Sears service center. If you need to order a

spark arrester, contact your local Sears service center.

The spark arrester must be serviced every 50 hours to

keep it functioning as designed.

If the engine has been running, the muffler will be very

hot. Allow the muffler to cool before servicing spark

arrester.

• Remove spark arrester screen for cleaning and

inspection.

• Replace if screen is damaged.

Air Cooling System

Over time debris may accumulate in cylinder cooling

fins and cannot be observed without partial engine

disassembly. For this reason, we recommend you have

an authorized Sears service dealer clean the cooling

system per recommended intervals (see “Maintenance

Schedule” on page 14). Equally important is to keep top

of engine free from debris. See “Clean Debris”.

Clean Combustion Chamber

We recommend you have an authorized Sears service

dealer remove combustion deposits from the cylinder,

cylinder head, top of piston and around valves per

recommended intervals (see “Maintenance Schedule”

on page 14).

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials.

• Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

Running engines produce heat.

Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, etc. can catch fire.

WARNING

Keep areas within heavy line clear of debris.

AFTER EACH USE

Water should not remain in the unit for long periods of

time. Sediments or minerals can deposit on pump

parts and “freeze” pump action. Follow these

procedures after every use:

1. Flush detergent siphoning tube by placing the filter

into a pail of clean water while running pressure

washer in low pressure mode. Flush for one to two

minutes.

2. Shut off engine, let it cool, then remove all hoses.

3. Disconnect spark plug wire from spark plug.

4. Empty pump of all liquids by pulling recoil handle

about 6 times. This should remove most liquid in

pump.

5. If storing for more than 30 days see “Long Term

Storage” on next page.

6. Coil high pressure hose and inspect it for damage.

Cuts in hose or fraying could result in leaks and

loss of pressure. Should any damage be found,

replace hose. DO NOT attempt to repair a

damaged hose. Replace hose with genuine Sears

part.

7. Disconnect hose from spray gun and high

pressure outlet on pump. Drain water from hose,

gun, and nozzle extension. Use a rag to wipe off

hose.

8. Reconnect spark plug wire to spark plug.

9. Store unit in a clean, dry area.

WINTER STORAGE

To protect the unit from freezing temperatures:

1. Flush detergent siphoning tube by placing filter

into a pail of clean water while running pressure

washer in low pressure mode. Flush for one to two

minutes.

2. Empty pump of all pumped liquids by pulling recoil

handle about 6 times. This should remove most

liquid in pump.

3. Use pump saver, available at a local Sears service

center, to treat pump. This minimizes freeze

damage and lubricates pistons and seals.

4. If pump saver is not available, connect a 3-foot

section of garden hose to water inlet adapter. Pour

RV–antifreeze (antifreeze without alcohol) into

hose. Pull recoil handle twice. Disconnect 3-foot

hose.

STORAGE

CAUTION

• Failure to do so will permanently damage your pump

and render your unit inoperable.

• Freeze damage is not covered under warranty.

You must protect your unit from freezing temperatures.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

WHEN DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Drain fuel tank outdoors.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

LONG TERM STORAGE

If you do not plan to use the pressure washer for more

than 30 days, you must prepare the engine and pump

for long term storage.

It is important to prevent gum deposits from forming in

essential fuel system parts such as the carburetor, fuel

filter, fuel hose or tank during storage. Also,

experience indicates that alcohol-blended fuels (called

gasohol, ethanol or methanol) can attract moisture,

which leads to separation and formation of acids

during storage. Acidic gas can damage the fuel

system of an engine while in storage.

Protect Fuel System

Fuel Additive:

If adding a fuel additive, fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote

fuel deterioration during storage. Engine and fuel can

be stored up to 24 months with additive.

• Add fuel additive following manufacturer’s

instructions.

• Make sure you have water supply to pump inlet

connected and turned ON.

• Run the engine outdoors for 10 minutes to be sure

that treated fuel has replaced the untreated fuel in

the carburetor.

If fuel additive is not used, remove all fuel from tank

and run engine until it stops from lack of fuel.

Change Oil

While engine is still warm, drain oil from crankcase.

Refill with recommended grade. See “Changing Oil”

on page 16.

Oil Cylinder Bore

• Remove spark plug. Squirt about 1/2 oz. of clean

engine oil into the cylinder. Cover spark plug hole

with rag. Pull recoil handle slowly to distribute oil.

Avoid spray from spark plug hole.

• Install spark plug. DO NOT connect spark plug

wire.

Protect Pump

To protect the pump use Sears pump saver to prevent

freeze damage and lubricate pistons and seals.

NOTE: Sears pump saver is available as an optional

accessory. It is not included with the pressure washer.

To use the pump saver:

1. Attach hose on pump saver can to pump inlet.

2. Push in can top to dispense pump saver.

3. When pump saver fluid begins to exit pump outlet,

the pump is protected.

4. Remove pump saver from pump inlet.

OTHER

• DO NOT store fuel from one season to another.

• If possible, store your unit indoors and cover it to

give protection from dust and dirt. BE SURE TO

EMPTY THE FUEL TANK.

CAUTION

• Failure to do so will permanently damage your pump

and render your unit inoperable.

• Freeze damage is not covered under warranty.

You must protect your unit from freezing temperatures.

• Always wear eye protection when using PumpSaver.

Read and follow all cautions and warnings on the

PumpSaver can label.

CAUTION

• DO NOT place a storage cover over a hot pressure

washer.

• Let equipment cool for a sufficient time before placing

the cover on the equipment.

Storage covers can be flammable.

WARNING

TROUBLESHOOTING

Problem Cause Correction

Pump has following problems:

failure to produce pressure,

erratic pressure, chattering, loss

of pressure, low water volume.

1. Nozzle in low pressure mode.

2. Water inlet is blocked.

3. Inadequate water supply.

4. Inlet hose is kinked or leaking.

5. Clogged inlet hose strainer.

6. Water supply is over 100°F.

7. High pressure hose is blocked

or leaks.

8. Gun leaks.

9. Nozzle is obstructed.

10. Pump is faulty.

1. Pull nozzle backward for high

pressure mode.

2. Clear inlet.

3. Provide adequate water flow.

4. Straighten inlet hose, patch

leak.

5. Check and clean inlet hose

strainer.

6. Provide cooler water supply.

7. Clear blocks in outlet hose.

8. Replace gun.

9. Clean nozzle.

10. Contact Sears service facility.

Detergent fails to mix with spray.

1. Detergent siphoning tube is not

submerged.

2. Chemical filter is clogged.

3. Dirty in-line filter.

4. Nozzle is in high pressure

mode.

1. Insert detergent siphoning tube

into detergent.

2. Clean or replace filter/detergent

siphoning tube.

3. See "Check In-Line Filter".

4. Push nozzle forward for low

pressure mode.

Engine runs good at no-load but

"bogs" when load is added.

Engine speed is too slow. Move throttle control to FAST

position. If engine still "bogs down",

contact Sears service facility.

Engine will not start; or starts

and runs rough.

1. Dirty air cleaner.

2. Out of fuel.

3. Stale fuel.

4. Spark plug wire not connected

to spark plug.

5. Bad spark plug.

6. Water in fuel.

7. Excessively rich fuel mixture.

8. Intake valve stuck open or

closed.

9. Engine has lost compression.

1. Clean or replace air cleaner.

2. Fill fuel tank.

3. Drain gas tank; fill with fresh

fuel.

4. Connect wire to spark plug.

5. Replace spark plug.

6. Drain gas tank; fill with fresh

fuel.

7. Contact Sears service facility.

8. Contact Sears service facility.

9. Contact Sears service facility.

Engine shuts down during

operation.

Out of fuel. Fill fuel tank.

Engine lacks power. Dirty air filter. Replace air filter.

La page charge ...

Simplicity 020248-0 Manuel utilisateur

Marque: Simplicity

Modèle: 020248-0

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020248-0 User manual

Simplicity 020248-0 Manuel utilisateur

Simplicity 020248-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents