RIDGID Outil de sertissage RP 240 Manuel utilisateur

RP 240/RP 241

Press Tools

• Français – 15

• Castellano – pág. 31

RP 240/RP 241 Manual

ii 999-995-106.10_REV. F

RP 240/RP 241 Press Tools

Table of Contents

Safety Symbols ....................................................................................................................2

General Safety Rules

Work Area Safety ..............................................................................................................2

Electrical Safety.................................................................................................................2

Personal Safety .................................................................................................................2

Power Tool Use and Care .................................................................................................3

Battery Tool Use and Care................................................................................................3

Service ..............................................................................................................................4

Specific Safety Information

Press Tool Safety ..............................................................................................................4

RIDGID Contact Information ...............................................................................................4

Description ...........................................................................................................................5

Specifications.......................................................................................................................7

Standard Equipment..........................................................................................................7

Pre-Operation Inspection ....................................................................................................7

Set-Up and Operating Instructions.....................................................................................8

Removing/Installing Attachment........................................................................................8

Preparing Connection........................................................................................................8

Pressing A Fitting With Typical Scissor Jaws....................................................................8

Pressing A Fitting With Typical Actuator And Press Ring Set...........................................9

Inspecting The Pressed Connection ...............................................................................10

Bluetooth Functions (Wireless Data Transfer) ................................................................10

Cold Weather Operation..................................................................................................10

Storage................................................................................................................................11

Maintenance Instructions..................................................................................................11

Cleaning And Lubrication ................................................................................................11

Troubleshooting...............................................................................................................11

Required Maintenance By RIDGID Independent Service Center....................................11

Service And Repair .........................................................................................................12

Optional Equipment ...........................................................................................................12

Disposal ..............................................................................................................................12

Electromagnetic Compatibility (EMC) ..............................................................................12

FCC/ISED Statement ..........................................................................................................12

EC Declaration of Conformity..................................................................Inside Back Cover

*Original Instructions - English

RP 240/RP 241

Press Tools

RP 240/RP 241

RP 240/RP 241 Press Tools

Record Serial Number below and retain product serial number which is located on nameplate.

Serial

No.

WARNING!

Read this Operator’s Man ual

carefully before using this

tool. Failure to understand

and follow the contents of this

manual may result in electri-

cal shock, fire and/or serious

person al injury.

Safety Symbols

In this operator’s manual and on the product, safety symbols and signal words are used

to communicate important safety information. This section is provided to improve under-

standing of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor

or moderate injury.

NOTICE indicates information that relates to the protection of property.

This symbol means read the operator’s

manual carefully before using the equip-

ment. The operator’s manual contains im-

portant information on the safe and proper

operation of the equipment.

This symbol means always wear safety

glasses with side shields or goggles when

handling or using this equipment to re-

duce the risk of eye injury.

This symbol indicates the risk of hands,

fingers or other body parts being crushed.

This symbol indicates the risk of electrical

shock.

plugs and matching outlets will reduce risk

of electric shock.

• Avoid body contact with earthed or

ground ed surfaces such as pipes, ra-

diators, ranges and refrigerators. There

is an increased risk of electrical shock if

your body is earthed or grounded.

• Do not expose power tools to rain or

wet conditions. Water en tering a power

tool will increase the risk of electrical shock.

• Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

• When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric shock.

• If operating a power tool in a damp lo-

cation is unavoidable, use a ground

fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk

of electric shock.

Personal Safety

• Stay alert, watch what you are doing

and use common sense when operat-

2999-995-106.10_REV. F

RP 240/RP 241 Press Tools

General Safety Rules*

WARNING

Read all safety warnings and instruc-

tions. Failure to follow the warnings and

instructions may result in electric shock,

fire and/or serious injury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTURE REFERENCE!

Work Area Safety

• Keep your work area clean and well lit.

Cluttered or dark areas invite accidents.

• Do not operate power tools in explosive

atmospheres, such as in the presence

of flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

• Keep children and by-standers a way

while operating a power tool. Distrac -

tions can cause you to lose control.

Electrical Safety

• Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified

NOTICE

DANGER

WARNING

CAUTION

* The text used in the General Safety Rules section of this manual is verbatim, as required, from the applicable UL/CSA

62841-1 standard. This section contains general safety practices for many different types of power tools. Not every

precaution applies to every tool, and some do not apply to these tools.

• Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool before

making any adjustments, changing ac-

cessories, or storing power tools. Such

preventive safety measures reduce the risk

of starting the power tool accidentally.

• Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

• Maintain power tools and accessories.

Check for misalignment or binding of

moving parts, breakage of parts and

any other condition that may affect the

power tool’s operation. If damaged,

have the power tool repaired before

use. Many accidents are caused by poorly

maintained power tools.

• Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

• Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for op-

erations different from those intended could

result in a hazardous situation.

• Keep handles and grasping surfaces

dry, clean and free from oil and grease.

Slippery handles and grasping surfaces

do not allow for safe handling and control

of the tool in unexpected situations.

Battery Tool Use And Care

• Recharge only with the charger speci-

fied by the manufacturer. A charger that

is suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

• Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

• When a battery pack is not in use, keep

it away from other metal objects, like

paper clips, coins, keys, nails, screws

or other small metal objects that can

make a connection from one terminal

to another. Shorting the battery terminals

together may cause burns or a fire.

ing a power tool. Do not use a power

tool while you are tired or under the

influence of drugs, alcohol, or medica-

tion. A moment of inattention while oper-

ating power tools may result in serious

personal injury.

• Use personal protective equipment. Al -

ways wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will

reduce personal injuries.

• Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energizing power tools

that have the switch ON invites accidents.

• Remove any adjusting key or wrench

before turning the power tool ON. A

wrench or a key left attached to a rotating

part of the power tool may result in per-

sonal injury.

• Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unex-

pected situations.

• Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing, and gloves away from moving

parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

• If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collection

can reduce dust-related hazards.

• Do not let familiarity gained from fre-

quent use of tools allow you to become

complacent and ignore tool safety prin-

ciples. A careless action can cause severe

injury within a fraction of a second.

Power Tool Use and Care

• Do not force power tool. Use the correct

power tool for your application. The

correct power tool will do the job better

and safer at the rate for which it is de-

signed.

• Do not use power tool if the switch does

not turn it ON and OFF. Any power tool

that cannot be controlled with the switch

is dangerous and must be repaired.

3

999-995-106.10_REV. F

RP 240/RP 241 Press Tools

Press Tool Safety

• Keep your fingers and hands away from

pressing attachments during press cy -

cle. Your fingers or hands can be crushed,

fractured or amputated if they become

caught between the attachment or between

these components and any other object.

• Never attempt to repair damaged press-

ing attachments (jaws, press ring, ac-

tuator, etc.). Discard the entire damaged

attachment. An attachment that has been

welded, ground, drilled or modified in any

manner can shatter during pressing re-

sulting in serious injury. Failure to replace

the entire pressing attachment may result

in component failure and serious injury.

• Large forces are generated during prod-

uct use that can break or throw parts

and cause injury. Stand clear during use

and wear appropriate protective equip-

ment, including eye protection.

• Only use RIDGID Press Tools with ap-

propriate RIDGID pressing attachments

(jaws, press ring, actuator, etc.). Other

uses or modifying the Press Tools for other

applications may damage the press tool,

damage the attachments and/or cause per-

sonal injury.

• Use proper tool, attachment and fitting

combinations. Improper combinations

can result in an incomplete joint, which

increase the risk of leaks, equipment dam-

age and injury.

• Before operating RIDGID® Press Tool,

read and understand:

– This operator’s manual,

– The attachment instructions,

– The battery/charger manual,

– The fitting manufacturer’s installation in-

structions,

– The instructions for any other equipment

used with this tool,

Failure to follow all instructions and warn-

ings may result in property damage and/or

serious injury.

RIDGID Contact

Information

If you have any question concerning this

RIDGID® product:

– Contact your local RIDGID distributor.

– Visit RIDGID.com to find your local

RIDGID contact point.

• Under abusive conditions, liquid may

be ejected from the battery; avoid con-

tact. If contact accidentally occurs, flush

with water. If liquid contacts eyes, addi-

tionally seek medical help. Liquid ejected

from the battery may cause irritation or

burns.

• Do not use a battery pack or tool that

is damaged or modified. Damaged or

modified batteries may exhibit unpredictable

behavior resulting in fire, explosion or risk

of injury.

• Do not expose a battery pack or tool to

fire or excessive temperature. Exposure

to fire or temperature above 265°F (130°C)

may cause explosion.

• Follow all charging instructions and do

not charge the battery pack or tool out-

side the temperature range specified in

the instructions. Charging improperly or

at temperatures outside the specified range

may damage the battery and increase the

risk of fire.

Service

• Have your power tool serviced by a

qual i fied repair person using on ly iden-

tical replacement parts. This will ensure

that the safety of the power tool is main-

tained.

• Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or author-

ized service providers.

Specific Safety

Information

WARNING

This section contains important safety

information that is specific to these tools.

Read these precautions carefully before

using the press tools to reduce the risk

of electrical shock or other serious in-

jury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTURE REFERENCE!

A compartment in the tool carrying case is

included to keep this manual with the tool

for use by the operator.

4999-995-106.10_REV. F

RP 240/RP 241 Press Tools

5 seconds. Once the cycle begins to deform

a fitting, it will automatically continue until

completion, even if the run switch is released.

The Tool Status Lights indicate things such

as improper temperature, low battery, or main-

tenance required. A work light turns on when

the run switch is depressed to illuminate the

work area. The head can be rotated for better

access in tight spaces.

The tools are supplied with a fabric loop that

can be used with appropriate attachments

such as shoulder straps or tie off lines.

The press tools include Bluetooth® wireless

technology to allow connection to smart

phones and tablets. See “Bluetooth Functions

(Wireless Data Transfer)” section for details.

– Contact Ridge Tool Technical Service

De part ment at ProToolsTechService@-

Emerson.com, or in the U.S. and Canada

call 844-789-8665.

Description

The RIDGID® RP 240 and RP 241 Press

Tools, when used with appropriate attach-

ments, are designed to mechanically press

fittings onto tubing to create a water-tight and

permanent seal, such as for plumbing and

heating applications. Attachments are also

available for other uses.

When the run switch on the press tool is de-

pressed, an internal electric motor powers a

hydraulic pump which sends fluid into the

cylinder of the tool, moving the ram forward

and applying force to the attachment, pressing

the fitting. The press cycle takes approximately

5

999-995-106.10_REV. F

RP 240/RP 241 Press Tools

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks

by Emerson Electric Co. is under license. Other trademarks and trade names are those of their respective owners.

Figure 1 – RIDGID RP 240 Press Tool and Compact Series Jaw

Figure 2 – RIDGID RP 241 Press Tool and Compact Series Jaw

# Description

1 Scissor Style Jaw Set

2 Attachment Mounting Pin

3 Tool Status Lights

4 ON/OFF Button

5 Warning Label

(RP 241 Underside)

6 Fabric Loop

7 Pressure Release Button

(RP 240 Far Side)

8 Handle

9 Battery

10 Run Switch

11 LED Work Light

12 Jaw Sideplate

2

135

6

4

7

9

10

11

8

12

1

3

5

4

9

6

8

11

12

7

10

2

5

6999-995-106.10_REV. F

RP 240/RP 241 Press Tools

Control Marking Description

Main tool power switch (I = ON, O = OFF).

ON/OFF Button ON: Press button until light turns on, See Figure 5 – Tool Status Lights

OFF: Press button until light turns off

Tool will automatically turn OFF if left unused for ten (10) minutes.

Run Switch

—

Depress to start press cycle, release when tool locks on. Releasing the

switch will not stop the tool once it has locked on. This assures consistent,

repeatable press joint integrity.

Pressure Allows tool to be released without completing press. If used, press connection

Release Button is not complete and must be repeated

Attachment — Holds attachment to tool. Must be fully inserted for tool to operate.

Mounting Pin

Figure 4 – Controls Chart

Icon

Solid Light Blinking Light

Description

Green Press completed. Light on for 10 s or until

Run Switch is pressed again.

Blue Bluetooth wireless is connected.

See Bluetooth Functions section.

Yellow

Indicates service interval approaching. Starts

2,000 cycles prior to service interval (30,000

cycles).

Tool is usable, but tool will lock after service

interval (32,000).

Yellow

Tool is locked. Tool has completed service in-

terval (32,000 cycles) and requires service.

Tool has malfunctioned. Remove and rein-

sert battery. If still ON, have tool serviced.

Red Attachment mounting pin is not fully inserted.

Red

Tool and/or battery out of Specification tem-

perature range. Bring the tool and battery to

correct operating temperature range.

Green Tool ON, ready to use.

Red Battery low. Tool will not operate. Recharge

battery/Insert fully charged battery

Figure 5 – Tool Status Lights

Green/Blue

Yellow

Red

Figure 3 – Machine Serial Number - Circled digits indicate the year and month of the manufacture.

(YY = year, MM = month).

ON\OFF Switch

IP32

XX YY MM XXX

risk of serious injury from electric shock,

crushing injures, attachment failure and

other causes, and prevent tool damage.

1. Remove battery from tool.

2. Clean any oil, grease or dirt from the

equipment, especially the handles and

controls. This aids inspection and helps

to prevent the tool or controls from slipping

from your grip.

3. Inspect the press tool for:

• Proper assembly, maintenance and com -

pleteness.

• Any broken, worn, missing, misaligned

or binding parts. Confirm fabric loop is

in good condition.

• Smooth movement of attachment mount-

ing pin between the fully open and fully

closed position. Pin should lock into each

position. Confirm that the run switch

moves freely and does not bind or stick.

• Presence and readability of warning la-

bels. See Figure 1.

• Any other condition which may prevent

safe and normal operation.

Standard Equipment

Refer to the RIDGID catalog for details on

equipment supplied with specific tool catalog

numbers.

Selection of appropriate materials

and joining methods is the responsibility of the

system designer and/or installer. Before any

installation is attempted, careful evaluation of

the specific service environment, including

chemical environment and service temperature,

should be completed. Consult Press Fitting

System manufacturer for selection information.

Pre-Operation

Inspection

WARNING

Daily before use, inspect your press tool

and correct any problems to reduce the

7

999-995-106.10_REV. F

RP 240/RP 241 Press Tools

Specifications

RP 240 Pistol Press Tool RP 241 Inline Press Tool

Attachments ..................RIDGID® Compact Series RIDGID® Compact Series

Motor:

Voltage ........................10.8 V d.c.

Amperage ...................24.1 A

Power ..........................260 W

Ram Force ....................5,400 lbs. (24 kN) 5,400 lbs. (24 kN)

Head Rotation ...............180° 180°

Duty Cycle.....................3 Press /min. 3 Press /min

Battery...........................12 V Li-Ion Rechargeable Battery Pack (RIDGID RB-1200 Series)

Bluetooth Range ...........33 ft. (10 m)

Ingress Protection.........IP32

Permissible Humidity ....80% maximum

Operating

Temperature .................15°F to 122°F (-10°C to 50°C)

Weight ...........................4.87 lbs. (2.21 kg) 4.72 lbs. (2.14 kg)

(No battery/attachment)

Dimensions ...................10.6" x 2.9" x 8.7" 13.4" x 3.4" x 4.4"

270 mm x 74 mm x 221 mm 340 mm x 86 mm x 112 mm

Sound Pressure (LPA)*.....<67.8 dB(A), K=1.5 dB(A) <65.2 dB(A), K=1.5 dB(A)

Vibration* .....................<0.72 m/s2, K=1.5 <0.65 m/s2, K=1.5

* Sound and Vibration measurements are measured in accordance with a standardized test per Standard EN 62481-1.

- Vibration levels may be used for comparison with other tools and for preliminary assessment of exposure.

- Sound and vibration emissions may vary due to your location and specific use of these tools.

- Daily exposure levels for sound and vibration need to be evaluated for each application and appropriate safety

measures taken when needed. Evaluation of exposure levels should consider the time a tool is switched OFF and

not in use. This may significantly reduce the exposure level over the total working period.

NOTICE

Do not use the press tool until any prob-

lems have been repaired.

4. Inspect and maintain tool attachments

per their instructions. Remove attachment

from the tool. Confirm that attachments

are in good condition and clearly marked

as to use.

5. Inspect and maintain any other equip-

ment being used per its instructions to

make sure it is functioning properly.

Set-Up and Operating

Instructions

WARNING

Keep your fingers and hands away from

the tool attachment during the press

cycle. Your fingers or hands can be

crushed, fractured or amputated in the

attachment or tool or between the at-

tachment, work piece and other objects.

Large forces are generated during prod-

uct use that can break or throw parts

and cause injury. Stand clear during use

and wear appropriate protective equip-

ment, including eye protection.

Use proper tool, attachment and fitting

combinations. Improper combinations

can result in an incomplete joint, which

increase the risk of leaks, equipment

damage and injury.

Follow setup and operation instructions

to reduce the risk of injury from crushing

and other causes and to prevent tool

damage.

1. Confirm have appropriate work area (See

General Safety Rules). Operate in clear,

level, stable, dry location. Do not use

tool while standing in water.

2. Inspect work to be done and determine

correct RIDGID tool and attachment for

the application per their specifications.

Using incorrect equipment for an appli-

cation can cause injury, damage the tool

and make incomplete connections.

3. Confirm all equipment has been inspected

and set up as directed in their instruc-

tions.

RP 240/RP 241 Press Tools

999-995-106.10_REV. F

8

Removing/Installing

Attachment

1. Remove battery from tool.

2. Fully open the attachment mounting pin.

Remove/insert the appropriate attachment

(Figure 6).

3. Fully close the attachment mounting pin.

The pin must be fully closed to prevent

tool damage during use.

Figure 6 – Attachment Mounting Pin

Preparing Connection

These instructions are generalized

practices for several types of press tool at-

tachments. Always follow the specific instruc-

tions for the press tool attachment being used

and the fitting manufacturers’ specific instal-

lation instructions to reduce the risk of improper

press connections and extensive property

damage.

1. Prepare the connection according to the

fitting manufacturers’ instructions.

2. With dry hands, insert a fully charged bat-

tery into tool. Depress ON/OFF button

one time to turn tool ON. Green light at

ON/OFF button should come on indicating

that the tool is ready to use. See Figure

5 – Tool Status Lights for any other lights.

NOTE: Tool will automatically turn OFF

if left unused for ten (10) minutes.

Pressing A Fitting With

Typical Scissor Jaws

1. Squeeze jaw arms to open jaws.

2. Place open jaws around fitting (Figure

7). Properly align jaw press profile with

contour of the fitting as specified in Fitting

Manufacturer's Installation Instructions.

Release jaw arms to close jaws around

fitting. Do not hang jaw set from fitting.

NOTICE

Tool could unexpectedly drop and cause

serious injury or death.

Figure 7 – Placing Scissor-Style Jaws Around

Fitting

Figure 8 – Jaws Square to Fitting

3. Confirm jaw is appropriately placed and

square to fitting. Keep fingers and hands

away from the jaws to avoid crushing

injuries in jaws or between jaws and sur-

roundings.

Depress the run switch (Figure 1/2). Once

the tool cycle begins and the rollers con-

tact the jaw arms, the tool will lock-on

and automatically complete the cycle.

Releasing the switch will not stop the tool

once it has locked on. This assures con-

sistent, repeatable press joint integrity.

If tool must be removed before a con-

nection is completed, depress the pres-

sure release button (Figure 1/2). Any

time release button is depressed, press

is NOT complete and the connection

must be pressed again to ensure com-

pletion. If the tool malfunctions during

operation, use this procedure.

RP 240/RP 241 Press Tools

999-995-106.10_REV. F 9

4. Release the run switch.

5. Squeeze jaw arms to open jaws.

6. Remove jaw from fitting. Avoid sharp

edges that may have formed on fitting

during pressing operation.

7. When operation is complete, depress

On/Off button one time to turn tool OFF.

Remove battery from tool.

Pressing A Fitting With

Typical Actuator And Press

Ring Set

1. Open ring and place around fitting. Pro -

perly align ring press profile with contour

of the fitting as specified in Fitting Manu -

fact urer's Installation Instructions. Release

ring to close around fitting.

2. Confirm appropriate actuator is installed

in tool. Squeeze actuator arms to open

the actuator tips. Align actuator tips with

ring pockets. Release actuator arms and

fully engage actuator tips into ring pock-

ets. Misaligning actuator tip to ring pocket

can damage the ring or actuator during

pressing. Do not hang tool and actuator

from press ring. Tool could unexpectedly

drop and cause serious injury or death.

3. Confirm ring is appropriately placed and

square to fitting. Keep fingers and hands

away from the actuator and ring to avoid

crushing injuries in attachment or be-

tween attachment and surroundings.

Depress the run switch. Once the tool

cycle begins and the rollers contact the

jaw arms, the tool will lock-on and auto-

matically complete the cycle. Releasing

the switch will not stop the tool once it

has locked on. This assures consistent,

repeatable press joint integrity.

If tool must be removed before a con-

nection is completed, depress the release

button (Figure 1/2). Any time release but-

ton is depressed, press is NOT complete

and the connection must be pressed

again to ensure completion. If the tool

malfunctions during operation, use this

procedure.

Figure 9 – Installing Press Ring onto Fitting

Figure 10 – Attaching Actuator to Press Ring

4. Release the run switch.

5. Squeeze actuator arms to open actuator.

Remove actuator from fitting.

6. Remove ring from fitting. Avoid sharp

edges that may have formed on fitting

during pressing operation.

7. When operation is complete, depress

On/Off button one time to turn tool OFF.

Remove battery from tool.

Inspecting The Pressed

Connection

1. Inspect the pressed fitting for:

• Full insertion of tube into fitting.

• Excessive misalignment of the tubes.

A slight amount of misalignment at a

pressed connection is considered nor-

mal.

• Incorrect attachment alignment with the

fitting contour. Distorted or deformed

fitting.

• Any other issues per the fitting manu-

RP 240/RP 241 Press Tools

999-995-106.10_REV. F

10

facturer. This could include the removal

of a control ring or decal (used to indi-

cate the connection has not yet been

pressed).

If any issues are found, remove fitting

and install a new connection.

2. Test connection in accordance with con-

nector manufacturer instructions, normal

practice and applicable codes.

Bluetooth Functions (Wireless

Data Transfer)

The RIDGID® RP 240 and RP 241 Press

Tools include Bluetooth® wireless technology

allowing wireless data transfer to properly

equipped smartphones or tablets (“devices”)

running iOS or Android operating systems.

1. Download the appropriate RIDGID® app

to your device by going to RIDGID.com/-

apps or by going to the Google Play Store

or Apple App Store.

2. When the tool is ON, a Bluetooth wireless

technology equipped device can find and

pair with the press tool.

3. In the Bluetooth settings of your device,

select desired RIDGID tool. Refer to your

device instructions for specific information

on how to connect via Bluetooth wireless

technology. Once connected, the blue

tool status light will be solid.

After the initial pairing, most devices will

automatically connect to the Tools when

the Bluetooth wireless technology is ac-

tive and in range. Press tools should be

less than 33 ft. (10 m) from the device

to be detected. Any obstacle between

the tool and device can reduce the op-

erational range.

4. Follow the app instructions for proper

use. Among other things, the app allows

monitoring of tool cycles.

5. The wireless data transfer turns OFF

when the press tool is switched OFF.

Turn Bluetooth wireless device OFF to

reduce device battery drain.

Cold Weather Operation

As temperature drops, hydraulic fluid thickens

and battery performance degrades. To reduce

the risk of improper operation, the RP 240

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks

by Emerson Electric Co. is under license. Other trademarks and trade names are those of their respective owners.

iOS is registered trademark of Apple Inc.

Android and the Android logo are trademarks of Google Inc.

RP 240/RP 241 Press Tools

999-995-106.10_REV. F 11

and RP 241 will not operate outside of the

specification temperature range as indicated

by the tool status lights (Figure 5).

When ambient conditions are outside the spec-

ification temperature range, keep the tool and

batteries in a conditioned space until ready

to use.

Storage

Remove battery from tool. Store press tool

and battery in case. Avoid storing in extreme

heat or cold. The tool will not turn ON if the

tool is outside the specification range. This

will be indicated by the tool status lights (see

Figure 5).

Store tool in a dry, secured,

locked area that is out of reach of children

and people unfamiliar with the Press Tools.

The tool is dangerous in the hands of un-

trained users.

Maintenance

WARNING

Make sure battery is removed from tool

before performing maintenance or mak-

ing any adjustment.

Cleaning And Lubrication

1. Wipe the tool clean daily with a clean dry

cloth.

2. Inspect the attachment mounting pin and

lubricate the pin with silicone lubricant as

needed.

3. Check return springs in attachments with

each use. Attachments should open and

close freely with only moderate finger ef-

fort required.

Required Maintenance By

RIDGID Independent Service

Center

The RP 240 and RP 241 Press Tools must

be serviced at set intervals by a RIDGID Inde -

pendent Service Center to ensure proper op-

eration. This will be indicated by a tool status

light (See Figure 5).

WARNING

SYMPTOM POSSIBLE REASON SOLUTION

Tool will not turn ON

when ON/OFF button

is pressed.

Attachment is locked

onto fitting.

The pressed connec-

tions produced are not

complete.

Oil leaks from tool.

Motor runs but tool will

not complete a cycle.

Tool stops during op-

eration.

Troubleshooting

Battery is completely discharged or

battery has failed.

Battery not properly inserted into han-

dle of tool.

Press was not successfully completed.

Used wrong jaws for the tube size or

material.

The tool was not square to the tube.

Attachment press contour was not a -

ligned with the fitting contour.

Tool is in need of repair.

Seal or mechanical problems.

Oil level low.

Insert fully charged battery/recharge

battery.

Check to assure battery is fully inserted.

Push pressure release button to remove

jaws from fitting. Inspect and repress

fitting.

Install the correct attachment.

Redo the joint with new fitting and new

tube. Make sure that the tool is square

to the tube.

Redo the joint with new tube and new

fitting. Make sure the attachment press

contour is aligned with the fitting con-

tour.

See Contact Information for nearest

RIDGID Independent Service center.

See Contact Information for nearest

RIDGID Independent Service center.

See Figure 5 for Tool Status Lights.

Service And Repair

WARNING

Improper service or repair can make the

machine unsafe to operate.

Service and repair on the RP 240 and RP 241

Press Tools must be performed by a RIDGID

Independent Press Tool Service Center.

For information on your nearest RIDGID Auth-

orized Inde pendent Service Center or any

service or repair questions, see Contact

Information section in this manual.

Optional Equipment

WARNING

To reduce the risk of serious injury, only

use equipment specifically designed and

recommended for use with the RIDGID

RP 240 and RP 241 Press Tools, such

as listed below.

RP 240/RP 241 Press Tools

999-995-106.10_REV. F

12

Ridge Tool Company provides Compact series

press attachments designed specifically for

use with RIDGID Compact Press Tools. Only

use attachments that are specifically designed

to press the fitting system you are installing.

For a complete listing of RIDGID equipment

available for these tools, see the Ridge Tool

Catalog online at RIDGID.com or see Contact

Information.

Disposal

Parts of these tools contain valuable materials

and can be recycled. There are companies

that specialize in recycling that may be found

locally. Dispose of the components in com-

pliance with all applicable regulations. Contact

your local waste management authority for

more information.

For EC Countries: Do not dispose

of elec trical equipment with house-

hold waste!

According to the European Guide -

line 2012/ 19/EU for Waste Elec -

trical and Electronic Equipment and

its imple men tation into national legislation,

electrical equipment that is no longer usable

must be collected separately and disposed

of in an environmentally correct manner.

Electromagnetic

Compatibility (EMC)

The term electromagnetic compatibility is

taken to mean the capability of the product

to function smoothly in an environment where

electromagnetic radiation and electrostatic

discharges are present and without causing

electromagnet interference to other equip-

ment.

These tools conform to all applica-

ble EMC standards. However, the possibility

of it causing interference in other devices

cannot be precluded. All EMC related stan-

dards that have been tested are called out

in the tool’s technical document.

FCC/ISED Statement

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

1. This device may not cause harmful in-

terference.

NOTICE

Catalog

No. Description

57418 RP 240 Battery Press Tool, Tool Only

57423 Carry Case, RP 240

RP 240 Press Tool

Catalog

No. Description

57288 RP 241 Battery Press Tool, Tool Only

57393 Carry Case, RP 241

RP 241 Press Tool

Catalog

No. Model Capacity

55183 RB-1225 12V 2.5Ah Li-Ion

Battery Packs

Battery will work with any catalog number RBC-121 Battery

Charger.

Catalog Plug

No. Region Type

55193 Charger USA, Canada and Mexico A

55198 Charger Europe C

55203 Charger China A

55208 Charger Australia & Latin America I

55213 Charger Japan A

55218 Charger United Kingdom G

44798 Charger Cord North America A

44808 Charger Cord Europe C

44803 Charger Cord China A

44813 Charger Cord Australia & LA I

44818 Charger Cord Japan A

44828 Charger Cord United Kingdom G

RBC-121 Chargers and Cords

RP 240/RP 241 Press Tools

999-995-106.10_REV. F 13

2. This device must accept any interference

received, including interference that may

cause undesired operation.

Modifications not expressly approved by this

company could void the user's authority to

operate the equipment.

This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reason-

able protection against harmful interference

in a residential installation.

This equipment generates, uses, and can ra-

diate radio frequency energy and, if not in-

stalled and used in accordance with the in-

structions, may cause harmful interference

to radio communications.

However, there is no guarantee that interfer-

ence will not occur in a particular installation.

If this equipment does cause harmful inter-

ference to radio or television reception, which

can be determined by turning the equipment

off and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving an-

tenna (radio/TV device).

• Increase the separation between the

equipment and receiver.

• Consult the dealer or an experienced

radio/TV technician for help.

This product complies with the Canadian

ICES-003 Class A specifications.

See Declaration label on tool.

RP 240/RP 241 Press Tools

999-995-106.10_REV. F

14

Sertisseuses

RP 240 et RP 241

Sertisseuses RP 240 et RP 241

Enregistrez ci-dessous pour future référence le numéro de série de l’appareil indiqué sur sa

plaque signalétique.

N° de

série

AVERTISSEMENT

Familiarisez-vous avec le manuel ci-

présent avant d’utiliser l’appareil. Tout

écart aux consignes données dans

celui-ci augmenterait les risques de

choc électrique, d’incendie et/ou de

grave blessure corporelle.

Sertisseuses RP 240 et RP 241

999-995-106.10_REV. F

16

Table des matières

Symboles de sécurité ........................................................................................................17

Consignes générales de sécurité

Sécurité des lieux ............................................................................................................17

Sécurité électrique...........................................................................................................17

Sécurité individuelle ........................................................................................................18

Utilisation et entretien des appareils électriques .............................................................18

Utilisation et entretien des appareils à piles ....................................................................19

Service après-vente ........................................................................................................19

Consignes de sécurité spécifiques

Sécurité de la sertisseuse ...............................................................................................19

Coordonnées RIDGID ........................................................................................................20

Description .........................................................................................................................20

Caractéristiques techniques .............................................................................................22

Equipements de série......................................................................................................23

Inspection de l’appareil .....................................................................................................23

Préparation et utilisation ...................................................................................................24

Retrait et montage des têtes de sertissage.....................................................................24

Préparation des raccordements ......................................................................................24

Sertissage des raccords à l’aide de mâchoires à cisaille typiques..................................25

Sertissage des raccords à l’aide d’actionneurs et jeux de bagues de sertissage typiques...25

Examen des raccords sertis ............................................................................................26

Fonctions Bluetooth (transfert de données à distance)...................................................26

Fonctionnement par temps froid (vérifications) ...............................................................27

Dépannage......................................................................................................................27

Stockage .............................................................................................................................28

Entretien..............................................................................................................................28

Nettoyage et lubrification de l’appareil ............................................................................28

Révisions obligatoires effectuées par un réparateur RIDGID agréé ...............................28

Révisions et réparations..................................................................................................28

Accessoires ........................................................................................................................28

Recyclage de l’appareil .....................................................................................................29

Compatibilité électromagnétique (EMC) ..........................................................................29

Déclaration FCC .................................................................................................................29

Déclaration de conformité CE......................................................recto de la page de garde

*Traduction de la notice originale

17

999-995-106.10_REV. F

Sertisseuses RP 240 et RP 241

Symboles de sécurité

Les symboles et mots clés utilisés à la fois dans ce mode d’emploi et sur l’appareil lui-

même servent à signaler d’importants risques de sécurité. Ce qui suit permettra de mieux

comprendre la signification de ces mots clés et symboles.

Ce symbole sert à vous avertir de risques d’accident potentiels. Le respect des consignes

qui le suivent vous permettra d’éviter les risques d’accident grave ou potentiellement mortel.

Le terme DANGER signifie une situation dangereuse qui, faute d’être évitée, provo-

querait la mort ou de graves blessures corporelles.

Le terme AVERTISSEMENT signifie une situation dangereuse potentielle

qui, faute d’être évitée, serait susceptible d’entraîner la mort ou de graves

blessures corporelles.

Le terme ATTENTION signifie une situation dangereuse potentielle qui, faute

d’être évitée, serait susceptible d’entraîner des blessures corporelles légères ou

Le terme AVIS IMPORTANT indique des informations concernant la protection

des biens.

Ce symbole indique la nécessité de bien

se familiariser avec la notice d’emploi avant

d’utiliser ce matériel. La notice d’emploi

renferme d’importantes consignes de sécu-

rité et d’utilisation du matériel.

Ce symbole indique la nécessité de

porter des lunettes de sécurité à œillères

ou des lunettes fermées lors de la ma-

nipulation ou utilisation de cet appareil

afin de limiter les risques de lésion ocu-

Ce symbole signale un risque d’écrase-

ment des doigts, des mains ou autres

membres.

Ce symbole signale un risque de choc

électrique.

• Eloignez les enfants et les curieux du-

rant l’utilisation des appareils élec-

triques. Les distractions risquent de vous

faire perdre le contrôle de l’appareil.

Sécurité électrique

• La fiche de l’appareil doit correspondre

à la prise de courant utilisée. Ne jamais

tenter de modifier la fiche d’une manière

quelconque. Ne jamais utiliser d’adap-

tateur de prise sur les appareils équipés

d’une fiche avec terre. Cela limitera les

risques de choc électrique.

• Evitez tout contact physique avec des

objets reliés à la terre tels que canali-

sations, radiateurs, cuisinières et réfri-

gérateurs. Tout contact avec la terre aug-

men terait les risques de choc électrique.

• N’exposez pas les appareils électriques

à la pluie ou aux intempéries. Toute

pénétration d’eau à l’intérieur de l’appareil

augmenterait les risques de choc élec-

trique.

• Ne maltraitez pas le cordon d’alimen-

tation de l’appareil. Ne jamais utiliser

le cordon pour porter, tirer ou déb-

Consignes générales de

sécurité*

AVERTISSEMENT

Familiarisez-vous avec l’ensemble des

consignes de sécurité et d’utilisation ci-

présentes afin d’éviter les risques de choc

électrique, d’incendie et/ou de grave

blessure corporelle.

Conservez l’ensemble de ces

consignes et instructions pour

future référence !

Sécurité des lieux

• Assurez-vous de la propreté et du bon

éclairage des lieux. Les chantiers en-

combrés ou mal éclairés sont une invitation

aux accidents.

• N’utilisez pas d’appareils électriques

en présence de substances volatiles

telles que liquides, gaz ou poussières

combustibles. Ce type de matériel risque

de produire des étincelles susceptibles

d’enflammer les poussières et émanations

combustibles.

AVIS IMPORTANT

DANGER

AVERTISSEMENT

ATTENTION

* Le texte utilisé dans les consignes de sécurité générales ci-présentes est tiré verbatim de la section de la norme UL/CSA

62841-1 applicable, comme l’impose la réglementation. Lesdites consignes de sécurité générales sont sensé couvrir de

nombreux types d’appareils électriques. Certaines d’entre-elles ne sont pas applicables à l’ensemble de ces appareils,

et certaines ne sont pas applicables à celui-ci.

Sertisseuses RP 240 et RP 241

Ne portez ni accessoires, ni bijoux.

Eloignez vos cheveux, vos vêtements

et vos gants des mécanismes lorsque

l’appareil fonctionne. Les foulards, les

bijoux et les cheveux longs risquent d’être

entraînés par les mécanismes en rotation.

• Vérifiez le bon raccordement et fonc-

tionnement des aspirateurs de pous-

sière éventuels. De tels aspirateurs peu-

vent limiter les risques associés à la dis-

persion des poussières.

• Ne permettez pas la familiarité issue

d’une utilisation fréquente de l’appareil

vous rendre complaisant au point d’ig-

norer les principes de sécurité applic-

ables. La moindre inattention peut engen-

drer de graves blessures corporelles dans

une fraction de seconde.

Utilisation et entretien des

appareils électriques

• Ne forcez pas l’appareil. Prévoyez l’ap-

pareil le mieux adapté aux travaux en-

visagés. Un appareil adapté produira de

meilleurs résultats et un meilleur niveau

de sécurité lorsqu’il fonctionne au régime

prévu.

• N’utilisez pas d’appareil dont l’interrup-

teur marche/arrêt ne fonctionne pas

correctement. Tout appareil qui ne peut

pas être contrôlé par son interrupteur est

considéré dangereux et doit être réparé.

• Débranchez l’appareil ou retirez son

bloc-piles avant tout réglage, remplace-

ment d’outils ou stockage. De telles

mesures préventives aideront à limiter les

risques de démarrage accidentel de l’ap-

pareil.

• Rangez les appareils électriques non

utilisés hors de la portée des enfants.

L’utilisation de cet appareil doit être

exclusivement réservé à du personnel

compétent. Tout appareil électrique peut

devenir dangereux entre les mains d’un

novice.

• Assurez l’entretien régulier des appa -

reils électriques et de leurs accessoires.

Assurez-vous de l’absence d’éléments

grippés ou endommagés, voire toute

autre anomalie susceptible de nuire au

bon fonctionnement et à la sécurité de

l’appareil. Faites réparer tout appareil

endommagé avant de le réutiliser. De

nombreux accidents sont le résultat d’ap-

pareils mal entretenus.

rancher l’appareil. Eloignez le cordon

de la cha leur, des matières grasses,

des objets tranchants et des mécan-

ismes. Les cordons d’alimentation endom-

magés ou entortillés augmentent les

risques de choc électrique.

• Lors de l’utilisation de l’appareil à l’ex-

térieur, prévoyez une rallonge électrique

homologuée pour ce type d’emploi. Cela

limitera les risques de choc électrique.

• S’il est inévitable d’utiliser l’appareil

dans des endroits humides, prévoyez

une source d’alimentation protégée par

disjoncteur différentiel. La présence d’un

disjoncteur différentiel limitera les risques

de choc électrique.

Sécurité individuelle

• Soyez attentif, restez concentré et faites

preuve de bon sens lors de l’utilisation

de ce type d’appareil. Ne jamais utiliser

ce matériel lorsque vous êtes fatigué

ou sous l’influence de drogues, de l’al-

cool ou de médicaments. Lors de l’utili-

sation d’un appareil électrique, un instant

d’inattention risque d’entraîner de graves

lésions corporelles.

• Prévoyez les équipements de protec-

tion individuelle appropriés. Portez sys-

tématiquement une protection oculaire.

Selon le cas, le port d’un masque à pous-

sière, de chaussures de sécurité antidéra-

pantes, du casque ou d’une protection au-

riculaire peut aider à limiter les risques de

lésion corporelle.

• Evitez les démarrages accidentels. As-

surez-vous que son interrupteur est

éteint avant de brancher l’appareil, y

introduire un bloc-piles, le soulever ou

le transporter. Porter un appareil électrique

avec son doigt sur l’interrupteur, voire le

brancher lorsque son interrupteur est en

position « Marche » est une invitation aux

accidents.

• Retirez toute clé ou dispositif de réglage

éventuel avant de mettre l’appareil en

marche. Une clé ou tout autre dispositif

de réglage engagé sur un élément mé-

canique pourrait provoquer un accident.

• Ne vous mettez pas en porte-à-faux.

Maintenez une bonne assiette et un bon

équilibre à tout moment. Cela assurera

un meilleur contrôle de l’appareil en cas

d’imprévu.

• Habillez-vous de manière appropriée.

999-995-106.10_REV. F

18

La page charge ...

RIDGID Outil de sertissage RP 240 Manuel utilisateur

Ce manuel convient également à

RIDGID Outil de sertissage RP 240 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents